A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength after 3 days.

Features
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Very Strong, durable bonding
Very high water resistance (e.g. OK for fixing tiles around the pool, but not below the water line. For this use Selleys Knead it Aqua)
Forms a rigid, durable bond
Can be used for gap filling (surfaces need not mate closely)
Good chemical resistance
Heat Resistant
Clamping is recommended to achieve a stronger bond
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 80°C but strength is regained when temperature drops

Appearance
Translucent

Where can this product be used?
Load bearing repairs
Gluing the head back on your hammer
Fixing a loose table or chair legs.
Bonding solid pieces of Aluminium sheeting
Bonding timber on your boat
Repairing splits and cracks in Cricket bats
Bonding fibreglass sheets
Repairing Ski’s
Fixing Dynabolts and metal rods into concrete

What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics
Crystal
Leather

How to use this product
Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
All traces of grease, rust paint, etc. should be removed.
For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bonding sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately.
When using tubes, Ensure correct caps are replaced on each tube or they will harden

Handy tips
For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
To extend product life replace caps immediately after use. Ensure you wipe excess from the nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the cap.
When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
Wipe off any uncured Araldite with acetone or nail polish remover.
To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquefy slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Clamping recommended for a stronger bond.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.

Safety tips
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Do not use solvents near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non-toxic when set. For further information refer to the Material Safety Data Sheet (MSDS).

Storage and re-use
Ensure caps are replaced and product stored in a cool dry place.