Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Also available in easy tube format. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces How to Use Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$12.50
A versatile hand kneadable, fast setting, non-rusting co-extruded epoxy repair system that can be used for repairing ferrous and aluminium metal items. It comes in a handy roll form, with the black hardener encapsulated in the grey resin part. The product hardens in 5-10 minutes, after mixing, to a black metal-like material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under water (but dry surfaces for application are best and recommended). Rapid Set (less than 10 minutes). Can be used for fuel resistant repairs. Appearance Dries Dark Grey/Charcoal Where can this product be used? Rebuilding engine parts and rusted metal etc Repairing a hole in a fuel tank Repair of iron pipes, tools and equipment Repair stripped threads Forming of nuts and bolts in place Attaching fixtures and signs Fixing radiators Repairing holes in cars and boats Patching ducts and tanks Making prototypes Thread locking Repair of down pipes and gutters Anchoring of bolts Repairing your metal outdoor furniture Set time increases at temperatures below 20°C Not recommended for plastic fuel tanks Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Not tested for drinking water contact to AS/NZ 4020:2005 What materials is this product suitable for? Steel Wide range of terrous metal and aluminium items Most plastics (pre-test required) Glass How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning Cut off required amount. Replace disc on remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to uniform colour. If mixing is difficult, warm to room temperature. Apply with pressure to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Steel will harden and begin to form a strong bond. After 60 minutes Knead-It Steel may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour, and feel a mild heat radiating from thre knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Store in a cool place for maximum shelf life Use Knead-It Multi Purpous for applications in contact with drinking water. Use Knead-It Aqua for applications in wet/submerged areas. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Steel. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$32.40
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$13.66
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$32.40
Features Resists intense heat Sets hard Water clean up Where can this product be used? Repairing bricks in fireplaces and chimneys Sealing flues in pot-belly stoves Filling cracks in ironworks and bricks What materials is this product suitable for? Brick Metal Concrete How to Use: Remove all dust, grease and loose debris before applying material. Dampen the cavities on porous surfaces for better adhesion. Apply Fireproof Cement firmly into holes and cracks with a damp knife or spatula. Allow Fireproof Cement to dry a minimum of 48 hours before exposure to heat. If Fireproof Cement is stiff slacken with a little water. Limitations: Fireproof Cement is not an adhesive - it is a filling compound. Not recommended for external use e.g. BBQ's, incinerators etc. Fireproof Cement is not suitable for use in kilns. Fireproof Cement is not recommended for moving joints such as expansion joints as it sets rigidly Hardened material cannot be resoftened with water.
$48.00
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications. Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried. Environmentally friendly Dries white Dries fast Very high weather resistance Unique properties make this product easy to shape and sand Ideal for schools and craft classes or just having fun!
$9.35
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$28.90
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$4.43
Polyfilla Rapid 30 140g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces Quick, Reliable, and Versatile Filler for All Surface Types If speed is of the essence, Polyfilla Rapid 30 140g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces. Key Features: Extremely easy to sand Sets to a hard finish Highly crack-resistant Fills up to 50mm deep holes Dries in as fast as 30 minutes* Suitable for multiple surfaces: plasterboard, brick, timber, and concrete How to Use: Clean and dry the surface, ensuring no loose or powdery material. Press the filler firmly into dents and holes, feathering edges to minimize sanding. Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications. For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat. Limitations & Tips: Use Poly Gap filler where joint movement occurs. Do not fill more than 50mm deep. Clean up with water before the filler dries. For quick paint-over solutions, consider using Poly Quick Dry. *Drying time is based on a 2mm application. With Polyfilla Rapid 30 140g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
$21.59
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. Filling blade included For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White Application • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the attached filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries FAQ's Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$38.10
A ready-mixed filler that dries hard to a durable finish for deep and wide cracks in mortar, concrete, cement render and brick. Water, weather, UV, algae and mould resistant Can be tooled to a render texture or sanded to a smooth finish. For use on: Bricks, concrete, bare or painted cement render & other masonry surfaces (EXTERIOR & INTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Available in: 500g and 2.2kg Colour: Cement grey in colour but can be painted over with both oil and water based paints • Ensure surfaces are clean and free from dust, grease, mould/algae and flaking/powdery paint or material. If necessary wash with Poly Sugar Soap. • Rinse thoroughly and allow surface to dry. • Use flexible filling blade to press filler into hole, or trowel to spread a thin layer over surface, and tool to a feathered edge. • Allow to dry (2–3 hours in thin 2–3mm applications, depending on temperature and humidity) before sanding and painting. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather. • For deeper jobs apply in 10mm layers, allowing each layer to dry before applying the rest. • Protect from rain until dry. If required, paint with a quality exterior coating. • For a render texture smooth out with trowel or filling blade when applying the product and do not sand. For a smoother texture sand surface after drying. • For best results, apply undercoat before applying water or oil based top coat. • Where joint movement occurs, use a flexible Poly sealant. • Clean up with water before filler dries.
$22.91
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink. For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR) Fill depth: Dependent on mix ratio Dries in: 2-3 hours Ready to use: NO (mix with water) Available in: 500g, 1kg, 2kg & 6kg Colour: Off-white • Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key. • Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate. • Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge. • Leave for 2-3 hours before sanding and decorating. • For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area. • Clean up with water before filler dries
$46.15
![Poly Gap Filler Sealant Multipurpose [White]](http://gluesaustralia.com.au/cdn/shop/files/9311531000683_aaee7eb0-0b5d-4d11-8699-1eea1db48c2c.png?v=1754712208&width=645)
A flexible multipurpose gap filler, to fill gaps around cornice, wall joints, skirting board, window and door frames where where movement causes ordinary fillers to crack or fall out. For use on: Wood, brick, aluminium, glass, plasterboard, ceramic tiles and painted surfaces (INTERIOR & EXTERIOR) Coverage: 30m/3mm bead. Dry time: Skins in 30 minutes at 25°C. Full cure in 7days. Ready to use: YES Available in: 475g Colour: White NOTE: Not for fine joints between tongue and groove boards or weatherboard overlaps. • Ensure surfaces are clean, dry and free from oil, dust, grease, flaking paint and old sealant. • Using caulking gun, push sealant ahead of nozzle forcing it onto the surface and into the joint. Ensure the sealant is touching both sides of the gap. • Smooth with wet finger or knife and remove excess sealant immediately with a damp cloth. • Allow sealant to skin approx 30 min before painting with water-based paints. • Allow to set for 48 hours if using oil based paint or if joint is large. • Some water-based undercoats and flat paints may crack on drying. Test a small section of sealant. Paint cracking may be reduced by using a vinyl/ acrylic semi glossed paint or oil based undercoats first, or by allowing the sealant to cure thoroughly before painting. • Do not use outside if rain is imminent, not for contantly damp areas. • Painting improves exterior durability. • Use Poly silicone sealants for a watertight seal or where movement is excessive. • Water clean up Q. How do I fill gaps between my wooden window frames and inside wall? A. You're dealing with two different materials here, plaster and wood. To allow for differential movement between them, use Polyfilla Gap Filler, wiping off any excess with a damp cloth. Q. I painted over the areas where I used Polyfilla Gap Filler and now cracks have appeared. Why has this happened? A. If the gap filler was not cured sufficiently before it was painted over, cracks can occur as the gap filler shrinks. To prevent this, allow 48 hours drying time when you are filling large gaps or painting with oil-based paints. Also, some water based undercoats and paints shrink during drying and as Polyfilla Gap Filler is flexible, it won't stop cracks appearing in the shrinking paint on its surface. Test the paint on a small section of gap filler and if this is a problem you can reduce cracking by allowing the filler to cure thoroughly or by first coating it with a vinyl/acrylic semi-gloss or oil-based undercoat. Q. Why does my gap filler keeps cracking? A. It is important to remember that the width of a gap affects how much the product can move. Fine cracks less than 2mm allow the gap filler to move only very tiny amounts before it may crack again. It is best to ensure that you have at least 3mm worth of product so you can maximise the movement capability of your joint.
$5.00
PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.
$16.17
Sandable Paintable Ready mixed Weather resistant Parfix multipurpose filler is a versatile, ready mixed filler ideal for filling cracks, holes and gaps inside and outside the home. Sandable and paintable, it enables a smooth finish.
$14.41
![Parfix Gap Filler Flexible Paintable Interior [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697115812_e966678a-f2ee-4e79-abc6-2f960851c302.png?v=1754712264&width=645)
Paintable Flexible Durable Parfix Gap Filler is a multi-purpose flexible filler that is suitable for interior applications such as skirting and architraves, door and window frames.
$3.65
![Monarch Mini Gap Filler [Brown]](http://gluesaustralia.com.au/cdn/shop/files/9320090030574_91b63521-91d4-427c-ba6f-c5f54343a9c6.jpg?v=1754712314&width=645)
$6.02
Get pro level finishes without the fuss. Gyprock CSR Less Mess Joint Compound is a pre mixed, easy sanding compound that helps you achieve smooth, paint ready walls with less splatter and minimal clean up. The handy 2.25kg tub is perfect for repairs, patching, jointing, and touch ups around the home or on site. Why you will love it Pre mixed convenience that is ready to use straight from the tub Less mess formula that helps reduce splatter and clean up time Easy to apply, easy to feather, and easy to sand smooth Low shrinkage for fewer repeat passes Paintable finish that accepts most interior paints Great for joints, screw head covering, corner repairs, and small patches Best suited for Interior plasterboard joints and repairs Skim coating small areas to blend texture Covering fasteners and minor cracks DIY touch ups and trade maintenance work How to use Surface prep: Ensure the area is clean, dry, dust free, and sound. Remove loose material and lightly scuff glossy paint. Application: Stir gently. Apply with a broad knife or trowel in thin, even coats. Feather edges well. Drying: Allow each coat to dry fully before recoating. Dry time varies with film thickness, temperature, and humidity. Sanding: Sand lightly with fine paper for a smooth finish. Remove dust before painting. Paint: Seal with a suitable primer then finish with your chosen interior paint. Tips for a flawless finish Work in thin passes rather than one heavy fill Keep your knife clean and slightly flexible for smooth feathering Use a dry sanding block or pole sander and avoid over sanding For deeper holes, build up in multiple coats Frequently asked questions Is it sandable and paintable? Yes. Once fully dry, sand lightly and prime before painting. Can I use it on previously painted walls? Yes, provided the paint is sound, clean, and lightly keyed. Is it suitable for wet areas? Use in dry interior spaces. For wet areas, follow local building guidelines and use appropriate systems. Specifications Brand Gyprock CSR Product Less Mess Joint Compound Pack size 2.25kg tub Colour Off white Use Interior plasterboard jointing and patching Cleanup Water while wet Finish Sandable and paintable Storage Reseal tightly. Store cool and dry. Do not allow to freeze. Good to know Coverage varies with joint size, substrate, and application method Dry times depend on thickness, temperature, and humidity Always test on a small area when working over sensitive or unknown coatings Safety Use in a well ventilated area Avoid breathing sanding dust. Wear a suitable mask and eye protection Keep out of reach of children Why buy from Glues Australia Fast dispatch Australia wide Careful packaging to protect your order Local support when you need advice
$35.43 $26.02
Strengthen joints, seams, and repairs with this tough fibreglass mesh tape. It helps prevent hairline cracks, improves bond strength, and delivers a smooth base for top coats on plasterboard and cement sheet surfaces. Why you will like it Reinforces joints to reduce cracking around seams and patches Open mesh allows compound to key through for a strong bond Clean edges for easy alignment along butt and tapered joins 50mm width suits standard plasterboard seams and corner work 20m roll is great for rooms, small renos, and ongoing touch ups Great for Plasterboard joins and butt joints Repairs around door and window openings Ceiling crack reinforcement Patching holes and dents before finishing Use with base coat and top coat compounds How to use Ensure the surface is clean, dry, and free of dust. Lay the tape centered over the joint or crack, pressing to seat it flat. Apply a generous first coat of compound through the mesh and let it dry. Feather additional coats wider than the last until flush with the surface. Sand lightly once dry, then prime and paint. Specifications Brand: Builders Edge Type: Fibreglass joint reinforcement tape Width: 50 mm Length: 20 m Material: Fibreglass mesh Colour: White Tips For best results, keep the tape flat with no bubbles before coating. Use a wider knife on each subsequent coat to blend the repair. Allow full dry time between coats to avoid shrinkage lines. Glues Australia helps Australians fix, build, and finish with confidence.
$13.21 $9.32
Achieve smooth, long lasting plasterboard joints with Gyprock CSR FibaFuse Joint Tape. This premium paperless tape bonds beautifully with both setting and drying compounds to reinforce seams, reduce the risk of cracks, and deliver a professional finish on walls and ceilings. Why choose FibaFuse Stronger joints thanks to an open fiber structure that integrates with joint compound for excellent reinforcement. Smooth finishing with feathered edges that sand and paint cleanly. No bubbling when properly embedded in compound for a flat, reliable seam. Works with most compounds including setting type and ready mixed formulas. Ideal for pros and DIY on new installs, repairs, and patchwork. Best for Joining plasterboard sheets on walls and ceilings Butt and tapered edge joints Repairs to cracked or previously patched seams High traffic areas that need extra durability How to use Prep Ensure surfaces are clean, dry, and free of dust. Lightly bevel cut edges if required. Bed coat Apply an even layer of joint compound over the seam at least the width of the tape. Embed Place the FibaFuse tape into the wet compound and press firmly with a taping knife to remove air pockets. Cover Apply a thin coat over the tape to fully conceal the mesh. Allow to dry or set as per the compound directions. Build Apply one or two wider coats, feathering the edges for a flat transition. Let each coat dry before the next. Finish Lightly sand, prime, and paint. Pro tips Keep knife pressure firm during embedding to avoid bubbles. Use a wider knife for second and third coats to reduce sanding. Prime before painting for a consistent sheen across joints and boards. Product details Brand Gyprock CSR Type Paperless joint tape for plasterboard seams Compatibility Setting and ready mixed joint compounds Applications Walls, ceilings, butt joints, tapered edges, repairs Frequently asked questions Do I need to pre soak the tapeNo. Embed the tape directly into wet compound. Can I use it with ready mixed compoundYes. It works with ready mixed and with setting type compounds. Follow the compound instructions for drying or set times. Will it show through paintNot when properly covered with compound, sanded smooth, and primed before painting. Good to know Store flat and dry to maintain tape integrity. Always wear appropriate PPE when sanding joint compound. Glues Australia helps you get a strong, professional finish without the fuss. Why buy new when you can fix
$21.78 $15.70
Dunlop Roof Repair Waterproofing Adhesive 310ml Seal, stick and stop leaks on the spot. This highly flexible, silane modified adhesive and sealant bonds and seals even in wet conditions, making it a smart fix for urgent roof, gutter and pond repairs. Why you will love it Works in the wet and can be applied underwater for minor repairs Flexible waterproof seal for joints, cracks and patches Strong adhesive grab for quick spot fixes Paintable once cured to match surrounding surfaces Low mess clean up while wet Ideal surfaces Concrete, wall panels, timber, waterproofing membranes, ceramic tiles, aluminium, plastics, metal, polystyrene foam, glass and glazed tiles. Typical uses Emergency roof and gutter leak sealing Sealing laps, flashings and penetrations Pond edge and minor underwater touch ups General crack and joint sealing around the home Spot fixing where fast, reliable adhesion is needed Directions Prep: Ensure the surface is firm and free of dust, oil and loose residues. Slightly damp surfaces are acceptable. Load: Remove the aluminium seal, pierce the nozzle membrane, fit and trim the nozzle, then place the cartridge in a caulking gun. Apply as a sealant: Gun a continuous bead over the joint or crack and allow to cure. Apply as an adhesive: Gun bead lines or spots, then press parts together within 7 to 10 minutes at 23°C, before skinning starts. For spot fixing, keep glue points 25 to 30 cm apart. Clean up: Wipe away any excess while wet with a clean cloth. Good to know Application temperature: 5°C to 35°C Dry and cure times vary with substrate and climate. Higher humidity shortens open time, lower humidity extends it. Colour: Grey. Can be over painted once dry. Always test paint compatibility on a small area first. Shelf life: 12 months in unopened packaging stored in a cool, dry place Packaging: 310 ml cartridge Safety Wear gloves and eye protection. Avoid inhaling vapours and ensure good ventilation. If in eyes, rinse with running water and seek medical advice. Keep out of reach of children. Warranty Backed by a 10 year product guarantee when used as directed. This is in addition to your rights under the Australian Consumer Law. Notes Do a trial application for underwater or constantly wet repairs, as long term stability depends on the specific situation. Not for chemical resistant applications. Remove any skinned layer in the nozzle before reusing an opened cartridge.
$21.97
Earl’s MulTflex® Exterior Flexible Filler is a unique, single-pack, ready-to-use flexible filler and adhesive formulated for lasting repairs on timber and masonry. It delivers a durable, non-shrinking, non-sinking finish that won’t crack with vibration and won’t fall out, making it ideal for exterior maintenance where movement and weather can defeat ordinary fillers. Paintable when dry and formulated with no volatile organic compounds (No VOCs), it’s a dependable, low-odour solution for professional results at home or on site. Proudly 100% Australian made and owned. Why you’ll love it Exterior-grade flexibility: absorbs movement and vibration without cracking. Non-shrink & non-sink: holds profile and edge detail after cure. Won’t fall out: engineered adhesion for long-term durability. Ready to use: straight from the tub — no mixing, no mess, no waste. Paintable: achieves a seamless, colour-matched finish once dry. No VOCs: low odour, solvent-free formula. Interior / Exterior: versatile enough for both. Proudly Australian: made and owned in Australia. Where it works Use Earl’s MulTflex® to repair and rebuild on a wide range of common building substrates: Timber: decks, window frames, trims, fascia, general carpentry repairs. Masonry: brick, block, render and patching mortar-like defects. Plasterboard: exterior-exposed linings under cover and general patching. Metals & gutters: non-structural filling and profiling (clean, sound, free of rust). Around pipes & penetrations: neat, gap-free finishing before painting. Glass & surrounds: edge repairs and feathering prior to topcoating. Ideal projects Rebuilding weathered or rotten timber edges before repainting. Filling cracks and surface imperfections in rendered walls. Profiling and feathering joints and transitions for a paint-ready finish. General exterior maintenance where a flexible, paintable filler is essential. Directions Surface Preparation Remove loose or flaking material, dirt, dust, oil, grease and chalky paint. Substrates must be sound. Ensure surfaces are dry and free from visible moisture. Treat rust and stabilize friable areas as required. For best mechanical key, lightly abrade glossy surfaces and remove dust. Application Open the tub and use directly. If the surface of the product begins to dry, add a few drops of water and re-mix gently. Keep the container tightly sealed when not in use. Apply with a filling knife or trowel, pressing firmly to ensure full contact with the substrate. Build up in thin layers for deep repairs, allowing each layer to firm before adding the next. For a satin-smooth finish, tool the final pass with a wet knife or brush to reduce post-work finishing. Finishing & Painting Allow to dry fully. Dry time varies with film thickness, temperature and humidity. Once dry, apply a suitable primer/undercoat if required by your paint system, then topcoat. Use quality exterior paints for weather-exposed areas. Clean-Up & Storage Clean tools and splashes with water while wet. Reseal immediately after use to minimise skinning and reduce waste. Store upright with lid sealed. Do not allow contents to dry out. Good to know Formulation is unaffected by normal temperature swings and resists cracking with vibration. Designed for exterior flexibility yet also suitable for interior touch-ups. For best results on deep voids, fill in multiple light applications rather than one heavy pass. Specifications Brand Earl’s Product MulTflex® Exterior Flexible Filler Type Single-pack, ready-to-use flexible filler & adhesive Use Interior / Exterior Paintable Yes, once fully dry VOC Content No VOCs (as supplied) Shrink / Sink Non-shrinking, non-sinking Flexibility Resists cracking with vibration and movement Clean-Up Water (while wet) Substrates Timber, masonry, render, plasterboard, metals, gutters, around pipes, glass Finish Satin-smooth when tooled with a wet knife or brush Packaging Ready-to-use tub Country of Origin 100% Australian made & owned Limitations Do not apply to unsound, dusty or actively corroding surfaces without proper preparation. Dry and cure times depend on depth and conditions; confirm dryness before painting. Not intended for structural repairs. Pro Tips Feather edges wide for invisible paint blending on weathered timber and render. Keep a small cup of clean water nearby to maintain a smooth final pass. Deep cavities: bridge with successive thin layers for the most stable result.
$22.00 - $28.00
Overview This high-quality general-purpose silicone sealant is a versatile solution for a wide range of sealing and bonding applications. Engineered with neutral cure technology, it is designed to provide a durable, flexible, and weather-resistant seal that remains reliable even in demanding environments. Once cured, the sealant forms a strong rubber-like finish that is permanently elastic, ensuring long-lasting performance both indoors and outdoors. Key Features Neutral Cure Technology: Low-odor curing system suitable for sensitive applications. Permanently Flexible: Retains elasticity over time without cracking or shrinking. Waterproof Protection: Provides a watertight seal, protecting against leaks and moisture ingress. Interior & Exterior Use: Unaffected by rain, snow, extreme temperatures, or prolonged UV exposure. Excellent Adhesion: Bonds strongly to most common building materials without primer. Easy Application: Smooth flow from the tube, easy to tool and clean before curing. Applications This sealant is designed for general-purpose use across a variety of materials and environments. Its flexibility and adhesion make it suitable for: Sealing around window and door frames. Lap joints in metal guttering and roofing sheets. Bonding panels such as wood, plasterboard, insulation board, and drywall. Fixing masonry joints including sills, brickwork, and decorative trims. Gap filling around pipes, conduits, and penetration surfaces. General sealing in kitchens, bathrooms, and living areas where flexibility is required. Limitations Not suitable for permanent water immersion (e.g., underwater joints or continuous water load). Not recommended for use on polyethylene (PE), polypropylene (PP), polycarbonate (PC), polymethyl methacrylate (PMMA), PTFE, neoprene, bituminous surfaces, or very soft plastics. Not intended for deep cavity filling without adequate moisture for curing. Surface Preparation To ensure maximum performance, surfaces must be clean, dry, and free from dust, grease, or loose particles. Non-porous surfaces should be wiped with solvent and dried with a clean cloth. Porous surfaces should be lightly abraded or brushed to remove contaminants and improve adhesion. Complete any painting work before applying the sealant. Application Instructions Remove the cap and pierce the nozzle seal. Apply steadily along the joint or surface, ensuring continuous contact. Smooth or tool the bead before skin formation occurs. If masking tape is used, remove immediately after tooling to avoid tearing the cured seal. Curing At room temperature (23°C), the sealant will skin over within 15 minutes and achieve full cure within 24 hours, depending on humidity and joint depth. Once cured, it provides a permanently flexible and weatherproof joint. Cleaning & Maintenance Excess uncured sealant can be cleaned using a cloth dampened with mineral turpentine. Fully cured material should be trimmed away carefully with a sharp blade. Store unused tubes in a cool, dry place below 25°C and away from direct sunlight. Shelf life is up to 12 months from the date of manufacture. Health & Safety Use in a well-ventilated area. Avoid contact with eyes and mucous membranes, as uncured sealant may cause irritation. In case of contact with eyes, flush thoroughly with water and seek medical advice. Keep out of reach of children. Always follow safety instructions and refer to the product’s safety data for detailed guidance. Why Choose This General Purpose Silicone Sealant? This sealant is a trusted choice for tradespeople, DIY enthusiasts, and homeowners seeking a reliable solution for everyday sealing needs. Its combination of flexibility, adhesion, and weather resistance ensures that once applied, it continues to protect and bond effectively for years to come. Whether you are fixing a leaking gutter, sealing around windows, or bonding decorative trims, this product provides professional results with minimal effort. Technical Specifications Technology Neutral Cure Silicone Appearance Clear Paste Working Time Up to 15 minutes Tack-Free Time Approximately 15 minutes Full Cure at 23°C 24 hours Flexibility Permanently elastic after curing Weather Resistance Unaffected by rain, snow, UV, and temperature variations Applications Windows, doors, guttering, masonry, panels, pipes, decorative elements Storage Below 25°C, out of direct sunlight Shelf Life 12 months from manufacturing date
$9.98
Skimming wall board top coat. Smooth ready to paint surface. Fine cracks, imperfections and feathering. Uni-Pro Smooth Coat Filler is the perfect final filler for skimming wallboard and plaster, giving a smooth, ready to paint surface. After base fillers have been applied, Smooth Coat's super fine, creamy texture makes filling fine cracks or surface imperfections easy and skims to a perfect feathered edge. Only a light sanding is required before painting.
$14.10
Skimming wall board top coat. Smooth ready to paint surface. Fine cracks, imperfections and feathering. Uni-Pro Smooth Coat Filler is the perfect final filler for skimming wallboard and plaster, giving a smooth, ready to paint surface. After base fillers have been applied, Smooth Coat's super fine, creamy texture makes filling fine cracks or surface imperfections easy and skims to a perfect feathered edge. Only a light sanding is required before painting.
$27.87
Casting, modelling, moulding, sculpting, carving. Fine quality to hold detail. Sands smooth.
$16.64
Casting, modelling, moulding, sculpting, carving. Fine quality to hold detail. Sands smooth.
$8.50
Ready to use, hard drying acrylic putty filler Ideal for repairing cracked, broken or uneven surfaces 30 minute fast drying time Includes bonus applicator Suitable for fibrous cement, brick, plaster and wood surface repairs available in 500gm/1.5kg Not suitable for wet areas or where structural movement occurs
$19.15
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/040074023437N_e5aad737-db85-4e62-bf16-291c599f76e3.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/04007_dddd7c02-55b5-4bc6-ae35-61e0db1a57f7.jpg?v=1754716410&width=645)
$33.09
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [White x 3m]](http://gluesaustralia.com.au/cdn/shop/files/9315284530329_412e3d45-40a8-4eca-9ed6-191f389472d4.jpg?v=1754716380&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [White x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_0ee281c8-0366-40a5-bb6c-b1a12d613ac2.png?v=1754716380&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$23.24
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Red x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1002_13c9931e-09ce-4d00-a35f-0df6977453aa.jpg?v=1754716370&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Red x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_54ba8b96-b758-4a94-8ba2-6b524d94e6ea.png?v=1754716370&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Clear x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1003_d0705a81-d0df-43a8-b8d2-cd06f5c78769.jpg?v=1754716354&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Clear x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_733528b0-7c24-46e0-889e-87698aafcb17.png?v=1754716354&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](http://gluesaustralia.com.au/cdn/shop/files/9315284530305_0485e2cc-4f7e-46c2-94ae-dee297210481.jpg?v=1754716346&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_50821584-e9cf-45b6-9528-1e997cfe48d7.png?v=1754716346&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$23.24
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](http://gluesaustralia.com.au/cdn/shop/files/9315284530374_556be8c2-fd79-4d44-bfb3-029f3b567466.jpg?v=1754716329&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](http://gluesaustralia.com.au/cdn/shop/files/93152845.png?v=1754716329&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$12.94
SIKA® FILLER-101 | FINE SURFACE FILLER Premium, fine surface filler Very fine consistency for fine surface filling Application thickness up to 3mm per layer Fast drying and easy to sand USE Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc. Smooth finish CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying COLOUR: White Appearance / Colour White paste Packaging 500 ml plastic tube Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion. Density ~ 1.100 kg/l Solid Content ~ 55% Grading Dmax : 0.12 mm Layer Thickness 3 mm max. Application Details Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-101 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-101 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: ~ 2 hours Paintability: ~ 4 hours Value Base All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
$94.64
SIKA® FILLER 107 | PLASTER FILLER Premium, wet area, fine surface filler Fine surface filler that will not rehydrate in humid conditions such as kitchens and bathrooms Application thickness up to 4mm per layer Suitable for use in exterior situations when overpainted USE Sika® Filler 107 is suitable for interior surface filling work on plaster, woven fabrics, old wallpapers, etc. in wet environments such as kitchens and bathrooms etc. CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying Not sensitive to moisture Appearance / Colours Grey / blue, grey paste Packaging 500 ml plastic tube 5 l and 10 l plastic pail Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion Density ~ 1.050 kg/l Solid Content ~ 62% Grading Dmax : 0.15 mm Layer Thickness 4 mm max. Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-107 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-107 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-107 can be applied with a spatula in layer thicknesses from 0 - 4 mm. When filling deep holes or cracks above 4 mm the filler should be applied in several layers and must be allowed to almost dry before each subsequent layer is applied. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: 2 to 4 hours (thicker applications might require longer time) Paintability: Approx. 12 hours
$21.53
SIKA® FILLER 107 | PLASTER FILLER Premium, wet area, fine surface filler Fine surface filler that will not rehydrate in humid conditions such as kitchens and bathrooms Application thickness up to 4mm per layer Suitable for use in exterior situations when overpainted USE Sika® Filler 107 is suitable for interior surface filling work on plaster, woven fabrics, old wallpapers, etc. in wet environments such as kitchens and bathrooms etc. CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying Not sensitive to moisture Appearance / Colours Grey / blue, grey paste Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion Density ~ 1.050 kg/l Solid Content ~ 62% Grading Dmax : 0.15 mm Layer Thickness 4 mm max. Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-107 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-107 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-107 can be applied with a spatula in layer thicknesses from 0 - 4 mm. When filling deep holes or cracks above 4 mm the filler should be applied in several layers and must be allowed to almost dry before each subsequent layer is applied. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: 2 to 4 hours (thicker applications might require longer time) Paintability: Approx. 12 hours
$16.43
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$20.57
Selleys Spakfilla Rapid is a ready-mixed lightweight filler that is fast drying, virtually non-shrinking, non-cracking & needs only one application. Features Fill cracks and holes in a single application Pre-mixed and ready to use Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water-based, so can be cleaned up with water Paintable with oil and water-based paints Where can this product be used? Filling cracks and holes on surfaces where no structural movement occurs Filling cracks in walls, ceilings, doors, windows Repairing holes in walls, ceilings, doors and windows What materials is this product suitable for? Wallboard Wood Masonry Plaster Primed nail heads Plasterboard Colours White Technology Water Based Use Interior Exterior (when painted) How To Use Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. Lightly sand back any excess filler from the surface after product dries (30 minutes in thin applications). Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting. Limitations: Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water. Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall. Nailing this product is not recommended. Avoid using below 5°C or in wet conditions. Handy Tips Painting with oil-based paints is not recommended until 24 hours after filler has been applied. Water based paints may be used immediately after filler has set. If filler is found to have stiffened prior to use, stir product. Product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency. Application tools may be cleaned with water. Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen. In exterior applications, protect from rain until dry and painted over with 2 coats of paint. Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry. For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times. Keep container closed when not in use. Clean Up Uncured product may be removed with water. Cured product can be removed by scraping or sanding.
$23.77
Key Features Fill cracks and holes in a single application Pre-mixed and ready to use Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water based, so can be cleaned up with water Paintable with oil and water based paints
$19.14
Selleys Spakfilla Coloursmart is a ready-mixed, lightweight filler which contains a dry time indicator that goes on pink and dries off-white, taking the guesswork out of knowing when to sand & paint! Features Fills cracks and holes in a single application Pre-mixed and ready to use Goes on pink and dries off-white when ready to sand Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water based, so can be cleaned up with water Paintable with oil and water based paints Where can this product be used? Filling cracks and holes on surfaces where no structural movement occurs Filling cracks in walls, ceilings, doors, windows Repairing holes in walls, ceilings, doors and windows What materials is this product suitable for? Plaster Wallboard Wood Plasterboard Masonry Fibrous cement Primed nail heads Size 180g Tub Colours Pink, dries off white Technology Water Based Use Interior Exterior Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. Lightly sand back any excess filler from the surface after product turns off-white (2 hours for holes up to 2mm deep). If more than 2mm deep, or in cold and humid conditions, expect longer drying times. Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting. Limitations: Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water. Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall. Nailing this product is not recommended. Avoid using below 5°C or in wet conditions.
$18.00
Selleys Paint Over Sealant is a permanently paintable sealant. Features Paintable Smooth flawless finish. Easy to use and can be used on damp surfaces. Superior adhesion to most building materials. Low odour so can be used in any environment without discomfort. Weather resistant by forming a durable seal which remains flexible, not drying or cracking Superior flexibility +/- 25% movement capability & up to 800% elongation or stretch. Temperature resistance – approximately -40°C +93°C Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. May be discoloured by contact with alloys containing brass, copper or zinc. Do not allow unused product to freeze. Where can this product be used? 10879.Window frames that need painting 102879.Capstones Masonry walls that need painting Perfect for use on or around: Bricks and concrete Windows frames Tiled and wooden fixtures Areas where a sealant is needed and where you want to paint it Not suitable for use in below waterline applications. Not suitable for use on oily woods such as cypress, teak or cedar. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Fibre Cement Painted Surfaces Ceramics Masonry Most metals Most plastics Wood How to use this product Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of sealant. Remove the tape before the sealant skins. For a better finish use a spatula dipped in detergent and water to tool off the sealant. Allow the surfaces to skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water based under coats & flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. To improve the paint finish, wipe the sealant with detergent solution immediately before painting. Avoid smearing sealant on the surrounding surfaces as this may effects its paintability. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin. Avoid breathing in vapours. Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use keep the nozzle on the cartridge Silicone is a reactive product and is designed to cure once exposed to air. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$25.00
Selleys No More Gaps Interior Colours is a flexible gap filler available in a range of modern colours, to fill those unsightly gaps and cracks around the home and take away the need to paint. Features Available in a great colour range, so no need to paint. Paintable if required. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for long. Has greater than 350% elongation/stretch and up to +/- 20% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage Can be painted over with both water and oil-based paints, after the surface has skinned. (Approximately 30 minutes after application). Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack Is formulated for long term resistance to cracking and crumbling. Is water-based, so can be cleaned up with water. Will not stain building materials. Has good resistance to weathering. Mould and mildew resistance. Where can this product be used? Between window and door frames and the wall. Along skirting boards. Around cornices. Between benchtops and tiles which are not exposed to water. In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm. What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Bare or painted surfaces Colorbond Many other building materials How To Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut the seal and nozzle and fit to the top of the cartridge. Insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun. Hold the caulking gun at a 45° angle and apply, forcing product into gap Smooth with a wet finger or spatula Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow surface to skin thoroughly prior to painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured. Avoid water contact until fully cured- 72 hours or longer in cold weather. Limitations: Not recommended for foot traffic areas, gaps between tongue and groove boards or weatherboard overlaps. Use Selleys(R) No More Gaps(R) Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards. Use Selleys(R) No More Gaps(R) Exterior & Weatherboard Gap Filler for weatherboard overlaps. Not suitable for areas in prolonged contact with water eg. showers, pools & spas. Where significant joint movement occurs, or for areas of frequent water immersion, use the appropriate Selleys(R) Silicone Sealant. Do not apply or store below 5°C. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying the product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. Allow the surfaces to the skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water-based undercoats and flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. Keep a pack of Selleys Sugar Soap Wipe handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$15.00
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$11.00
![Selleys No More Gaps Coloured Caulk Sealant 450g [Tranquil Retreat]](http://gluesaustralia.com.au/cdn/shop/files/18cfd18e466f43bab8a6fd2d1eaf4bfd.jpg?v=1757753110&width=645)
$15.00
![Selleys No More Gaps Coloured Caulk Sealant 450g [Timeless Grey]](http://gluesaustralia.com.au/cdn/shop/files/047808da6e434754b1b4b492e02434e9.jpg?v=1757753116&width=645)
$15.00
![Selleys No More Gaps Bricks Mortar [Medium Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697130327_41339ef1-92ff-417a-bab1-8529f0ee07f6.png?v=1754711845&width=645)
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C. Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$22.93
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$13.00
You have seen 96 out of 149 products
Targeted solutions for hairline and wider cracks in wood, plaster, masonry and more. Pick flexible sealants for moving substrates, or rigid fillers/epoxies for structural areas. Use filters to refine by substrate and set speed. Always review the product page and TDS/SDS.
