Aerosol Can

Gorilla Spray Adhesive is heavy duty, multi-purpose and easy to use. Gorilla Spray Adhesive forms a clear, permanent bond that is moisture resistant and can be used on projects both indoors and out. This spray adhesive is also photo safe. Its wide pad nozzle and controlled, fine mist spray provide an even application on the project you are working on. PRODUCT FEATURES HEAVY DUTY: Dries Permanent EASY TO USE: Repositionable CLEAR COLOR: Non-Yellowing* INDOOR & OUTDOOR: Moisture Resistant CONTROLLED SPRAY: Even Application WIDE PAD NOZZLE PHOTO SAFE All surfaces should be clean and free of dirt, grease and oil. Protect surrounding areas from overspray to avoid residual adhesive. Shake can well before using. Hold the can 15 to 20cm from surfaces to be bonded and spray an even coat of adhesive. For Maximum Bond Strength: Spray both surface to be joined. Allow to dry to tack (approximately 1 minute) and press surfaces firmly together. For Repositionable Bonds: Spray a light even coat on one surface. Allow to dry 1-3 minutes before joining. Repositionable up to 10 minutes depending on surface type, then bond becomes permanent. To remove, gently peel from corner. Tip: To avoid possible clogging, turn can away from body, turn upside down and spray a short jet of clear gas after completing the job. *Not recommended for use on vinyl materials, automotive headliners, polypropylene, polyethylene or similar materials. Do not use for bonding weighted materials. APPLICATION TEMPERATURE – 10°C to 32.2°C OUTDOOR – Yes MOISTURE RESISTANT – Yes PAINTABLE –Yes SANDABLE – Yes STAINABLE – No CURED COLOR – Clear PHOTO SAFE – Yes How do I remove Gorilla Spray Adhesive from my surface? To clean surface while adhesive is still wet/uncured, wipe adhesive off the project with a dry cloth.  Isopropyl alcohol (IPA) may be used according to manufacturer’s instructions. Once cured, Gorilla Spray Adhesive may be removed using mechanical means by gently scraping surface, being careful not to damage the surface underneath. How do I remove Gorilla Spray Adhesive from body/skin? While still wet, Gorilla Spray Adhesive can be removed by wiping adhesive with a dry cloth, and then washing the area with soap and water.  Once cured, rinse well with water. Is Gorilla Spray Adhesive food safe? Gorilla Spray Adhesive is not recommended for direct or indirect food contact and should not be considered food safe. What surfaces will Gorilla Spray Adhesive bond to? Gorilla Spray Adhesive is a multi-purpose product that will bond a wide variety of surfaces including fabric, paper, wood, plastic*, cardboard, foam, metal and more! NOTE: Not recommended for use on polypropylene (PP) or polyethylene (PE) plastics, vinyl, or any type of rubber with high oil or plasticizer content.  Not for use on food contact surfaces. Will Gorilla Spray Adhesive bond vinyl/acrylic/rubber? Gorilla Spray Adhesive will work well on many types of plastic; however, we do not recommend for use on polypropylene (PP) or polyethylene (PE) plastics, vinyl, or any type of rubber with high oil or plasticizer content.

Read more less

Glitz Furniture Polish Deep Wood Shine Formula 250ml revives tired timber and leaves a rich protective sheen that resists fingerprints and everyday dust. Ideal for routine care or quick touch ups, this easy to use polish helps nourish the surface so your furniture looks clean, smooth and beautifully refreshed. Why you will love it Deep wood shine that enhances natural grain and color Helps hide light swirl marks and minor dullness Protective layer that resists dust and fingerprints Quick wipe on, buff off application with no sticky residue Fresh, clean finish suitable for regular maintenance Best for Sealed timber furniture including tables, chairs, dressers and shelves Veneers and lacquered or polyurethane sealed wood surfaces Interior use around the home and office How to use Dust the surface thoroughly. Shake bottle well. Apply a small amount to a clean, soft cloth. Work in light, even sections, following the grain. Allow a brief haze to form, then buff with a dry cloth to a high shine. Repeat on dull patches as needed. A little goes a long way. Care tips Test on a small inconspicuous area before first use. Use gentle pressure to avoid swirl marks. Always buff with a clean cloth. For heavy grime, clean the surface first, allow to dry, then polish. Maintain regularly for the best long term appearance. Good to know Not suitable for raw, oiled or waxed timber, unsealed wood, floors or food preparation surfaces. Avoid use on high gloss piano finishes unless the manufacturer approves polishing. Keep off fabric, carpets and porous materials. Safety and storage Use in a well ventilated area. Keep out of reach of children and pets. Avoid contact with eyes. If splashed, rinse with water. Store upright in a cool, dry place. Replace cap after use. Frequently asked questions Will this leave a greasy filmWhen applied sparingly and buffed as directed, it leaves a clean sheen with no greasy residue. Can I use it on laminateYes on sealed laminate furniture. Do not use on flooring laminate. How often should I polishLightly every 2 to 4 weeks or whenever surfaces look dull. Specifications Product Furniture polish Finish Rich sheen Use Indoor, sealed wood and furniture surfaces Size 250 ml Application Cloth apply and buff What is in the pack 1 x Glitz Furniture Polish Deep Wood Shine Formula 250ml

Read more less

Introducing Selleys Water Shield, your go-to solution for making your fabrics water, snow, and ice-repellent without compromising comfort and breathability. Ideal for active individuals and outdoor enthusiasts, this product is designed to keep you dry while ensuring maximum comfort. Key Features Water, Snow, and Ice Repellent: Provides an effective barrier against moisture and cold elements. Breathable: Does not impair the comfort and breathability of the material, making it ideal for sportswear. Where to Use Sportswear, such as ski parkas, gloves, etc. Athletic shoes, including sandshoes and jogging shoes. Camping gear, like tents and sleeping bags. Cloth and canvas bags. Umbrellas. Outdoor furniture, e.g., canvas chairs. Paper maps and plans. Suitable for the Following Materials: Fabric Canvas Nylon How to Use Preparation: Ensure that the item to be treated is clean and dry. Application: Hold the aerosol can upright, approximately 100-150mm (4-6 inches) away from the surface. Spray: Use a sweeping motion to spray until the surface is moist. Dry: Allow approximately 3 hours for drying before using the item. Limitations Not suitable for leather or suede articles. Avoid use on fabric already treated with water repellents like DRW or waterproof materials like Gore-tex® or Driza-bone®. Do not apply to areas that don't require protection (e.g., soles of shoes). Handy Tips Test for colorfastness in an inconspicuous area before full application. Start spraying light-colored areas first, followed by darker areas. Launder or dry-clean soiled articles as usual and reapply the Water Shield. Specifications Size: 200g Aerosol Can Color: Colourless Technology: Silicone-Based Use: Suitable for both interior and exterior applications Keep your gear and clothing dry and comfortable. Experience the protection and convenience of Selleys Water Shield today!

Read more less

Selleys KwikGrip Spray 150g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces Adhesive Mastery: Quick, Clear & Heat Resistant Discover the power of Selleys KwikGrip Spray 150g, a versatile adhesive spray that bonds instantly on contact. Ideal for both absorbent and non-absorbent surfaces, it offers a quick-drying and heat-resistant solution for a multitude of projects. Key Features: Versatile adhesive spray Durable bond Fast drying and dries clear Heat resistance up to 70°C Common Applications: Car upholstery repairs Fixing laminate on tables and bench tops Patching vinyl flooring Art and craft projects And many more... Compatible Materials: Laminated plastics Timber Craft foam Aluminium Leather Canvas Rubber Most plastics* How to Use: USE ONLY IN A WELL VENTILATED AREA. Shake the can well. Ensure surfaces are clean and dry. Hold the can 20cm away and spray surfaces evenly. For a permanent bond, spray both surfaces and wait until touch dry before pressing together. Clamp overnight for a firm bond. For a temporary bond, spray one surface and press together while still tacky. Limitations: Not suitable for bonding rough, ill-fitting surfaces or certain plastics like polyethylene or polypropylene. Refer to the guidelines for alternative solutions. Handy Tips: After use, clean the nozzle by inverting the can and spraying until clear

Read more less

Selleys Kwik Grip High Temp Spray: Heat & Water Resistant Adhesive for Extreme Conditions Bond Like a Pro: From Marine Carpets to Car Interiors Presenting Selleys Kwik Grip High Temp Spray, a premium adhesive formulated to withstand extreme heat up to 90 degrees and resist salt water. Ideal for tasks requiring high-grade adhesion, from car headlining repairs to marine carpet installations. Key Features: Heat resistant up to 90 degrees Water and salt water resistant Fast drying High grab Applications Include: Repairing headlining in cars Adhering marine carpets in boats Suitable Materials: Wood Metal Aluminium Fabric Polyurethane foam Laminate Leather Felt Cork How to Use: Clean and dry the surface before application. Shake the can well and hold it 20cm away from the surface. Spray both surfaces liberally. Wait for up to 5-10 minutes for the adhesive to become touch dry. Align and press the surfaces together, applying

Read more less

Speeds the cure of Loxeal anaerobic products, including: Threadlockers 55-03 and 83-54, thread sealants 55-14 and 85-86, retaining compounds 53-11 and 82-21, and gasketing 58-14, 58-31 and 59-10. Loxeal Activator 11 Anaerobic Accelerator Spray 200ml Loxeal Activator 11 cleans, degreases and dramatically accelerates the cure of anaerobic adhesives and sealants – threadlockers, threadsealants, retaining compounds and gasketing products. It is the answer when anaerobic products cure slowly or unreliably: on passive surfaces (such as stainless steel, plated finishes and many alloys), at low temperatures, or across larger gaps. Spray one surface, let the solvent flash off for a few seconds, and fixture is typically achieved in 20–120 seconds. Supplied as a 200ml aerosol for fast, even coverage. Why choose Loxeal Activator 11? Speeds anaerobic fixture time to 20–120 seconds depending on adhesive, gap and temperature Cleans and degreases the joint in the same step Reliable curing in tough conditions – passive metals, cold workshops, larger gaps Long-lasting activation – treated parts remain active for up to three months when protected from dust and weathering Suitable for both threaded and flange joints Convenient 200ml aerosol spray application Typical applications Pre-treating stainless steel, zinc-plated and other passive fasteners before threadlocking or threadsealing Accelerating retaining compounds on bearings, bushes and cylindrical assemblies Speeding gasket and flange sealant cure in cold conditions or production settings How to use Spray Activator 11 onto one of the surfaces to be joined. Allow the solvent to evaporate for a few seconds until the surface is dry. Apply the anaerobic adhesive or sealant to the other surface. Assemble the parts; fixture typically occurs within 20–120 seconds. Specifications Composition Organic activating agents in solvent carrier Appearance Green liquid Viscosity (+25°C) 1–2 mPa·s Specific weight (+25°C) 0.8 g/ml Flash point (COC/DIN/ISO 2592) +21°C Cure acceleration Fixture in 20–120 seconds (adhesive, gap and temperature dependent) On-part activation life 24 hours; up to 3 months if parts are protected from dust and atmospheric agents Breakaway torque (ISO 10964, ref. 83-54) >5 Nm after 5 minutes Pack size 200ml aerosol spray Shelf life 1 year unopened at +25°C Important notes Use of an activator may reduce the final mechanical strength of the anaerobic bond Wait for the solvent to fully evaporate before assembling parts Flammable – keep away from ignition sources and use with good ventilation Store in a cool, dry place at no more than +25°C; do not refill containers with used product Safety Consult the Safety Data Sheet (SDS) before use. Flammable aerosol: keep away from heat, sparks and open flames, use in a well-ventilated area and avoid inhaling vapours. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

The recommended surface prep for Loxeal adhesives and sealants: Use before threadlockers, retaining compounds, gasketing, epoxies, structural acrylics and instant adhesives for maximum bond strength. Often paired with Activator 11 for anaerobics or Activator 9 for super glues. Loxeal Cleaner 10 Degreaser Spray 400ml Loxeal Cleaner 10 is a non-CFC, solvent-based cleaner and degreaser for preparing surfaces before bonding or sealing with adhesives and sealants. This 400ml aerosol puts fast, controlled surface prep straight in your hand: spray, wipe, and the solvent flashes off in around 60 seconds leaving a clean, dry, non-corroded surface ready for adhesive. Cleaner 10 has no effect on the cure speed or final strength of Loxeal adhesives and sealants – but a dirty joint certainly will. Why choose Loxeal Cleaner 10 spray? Convenient aerosol application – even coverage on parts, threads and hard-to-reach areas Fast flash-off – dries in about 60 seconds at room temperature Non-corrosive and residue-free on metals Does not interfere with adhesive cure speed or bond strength Ideal partner for threadlockers, retainers, epoxies, structural acrylics and instant adhesives Non-CFC solvent formulation Typical applications Spray-degreasing fasteners, threads and machined parts before threadlocking or retaining Cleaning oil- and grease-contaminated surfaces in maintenance and assembly work Preparing treated, coated or plastic substrates prior to bonding (check compatibility first) How to use Spray Cleaner 10 directly onto the surfaces to be bonded. While still wet, wipe with a clean cloth to remove heavy contamination. Allow the solvent to evaporate until the surface is completely dry (about 60 seconds). Apply the adhesive or sealant immediately after drying and assemble the joint. Specifications Formulation Non-CFC solvent blend Appearance Colourless liquid Boiling range +92°C to +102°C Flash point (COC/DIN/ISO 2592) -1°C (highly flammable) Density (+25°C, DIN 51757) 0.70 g/ml Drying time (+25°C) Approx. 60 seconds Water solubility Not soluble Corrosivity None Pack size 400ml aerosol spray Shelf life 12 months at +5°C to +25°C Important notes The solvent can affect certain plastics and coatings – check compatibility on a hidden area first Unclean or partially cleaned surfaces can significantly reduce adhesive performance Pressurised container – protect from sunlight and do not expose to temperatures above +50°C Store between +5°C and +25°C in a cool, dry place Safety Consult the Safety Data Sheet (SDS) before use. Highly flammable aerosol: keep away from naked flames, sparks and non-flameproof electrical equipment, use only in well-ventilated areas, avoid prolonged skin contact and do not smoke near the product. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

Give your home a crisp eucalyptus lift with this antibacterial air and surface freshener from Glitz. It tackles everyday odours, leaves a clean eucalyptus scent, and is suitable for quick freshen ups in bathrooms, kitchens, bins, pet areas, and cars. Why you'll like it Antibacterial formula for hygienic freshening of hard, non porous surfaces Clean eucalyptus fragrance that smells fresh without being overpowering Fast acting spray ideal for busy households and shared spaces Versatile use in bathrooms, toilets, bins, shoes, gym bags, and vehicles Convenient 200 g aerosol that fits easily in cupboards and glove boxes Where to use Air freshening in bathrooms, laundries, living rooms, and entryways Hard, non porous surfaces such as benches, sinks, tiles, bins, door handles Cars, caravans, and small spaces that need a quick refresh How to use Shake can well before each use. For air freshening: hold can upright and spray into the center of the room for a few seconds. Allow mist to disperse. For surfaces: spray from 20 to 25 cm away onto hard, non porous surfaces until lightly covered. Spread with a clean cloth and allow to air dry. For food contact areas rinse with potable water after use. Repeat as needed. Always test on a small inconspicuous area first. Good to know Do not use on fabrics, leather, or polished wood Not for personal hygiene or use on skin Use only as directed in a well ventilated area Specifications Brand Glitz Product Antibacterial Eucalyptus Spray Fresh Air Cleaner Net Weight 200 g Format Aerosol spray Fragrance Eucalyptus Suitable Surfaces Hard, non porous household surfaces Country of Use Australia Safety Flammable aerosol. Pressurised container. Keep away from heat, hot surfaces, sparks, open flames, and ignition sources. No smoking. Refer to the Safety Data Sheet (SDS) for full details. Frequently asked questions Can I use it on fabric or carpetsIt is designed for air freshening and hard, non porous surfaces. For fabrics test a hidden area first. Prolonged wetting may mark textiles. Does it remove strong bin and pet odoursYes, it helps neutralise common household odours and leaves a fresh eucalyptus scent. For persistent odours clean the source before spraying. Is it safe for kitchensYou can use it on hard kitchen surfaces. Rinse food contact areas with potable water after treatment. Shipping and returns Ships Australia wide from our Victorian warehouse Aerosols travel by road only. Express options may be limited Change of mind returns accepted within our store policy when unopened and in resalable condition Tip: Pair with bin liners and cleaning vinegar for a simple fresh home routine.

Read more less

Selleys Ezy Glide: The Dry Lubricant Solution for Any Surface, Anywhere No More Squeaks, No More Sticking: All-Surface Dry Lubricant Introducing Selleys Ezy Glide, a dry, non-oily lubricant that offers long-lasting lubrication while avoiding dirt and dust accumulation. Designed for a multitude of surfaces, it's your go-to for making things glide effortlessly. Key Features: Contains a dry lubricant (PTFE) Dries clear Long-lasting lubrication Does not attract dirt and dust Non-oily lubricant Applications Include: Windows Drawers Zipper Doors Locks Indoor/Outdoor Furniture Roller Door Tracks Curtain Tracks Sailboat Runners Children's Toys Sliding Glass Doors and Mirrors Suitable Materials: Wood Metal Leather Other Absorbent Surfaces How to Use: Shake the 150g aerosol can well. Hold the can approximately 80-100 mm (3-4") from the surface and spray lightly. Allow a few minutes for drying. Limitations & Tips: Ezy Glide may not be compatible with some materials like plastics, and it produces a slippery coating. Test in an inconspicuous area first and avoid over-spraying onto floors. Use the extension tube for hard-to-reach areas. Ezy Glide does not contain silicone. Avoid overspraying on fabric as it may mark the material.

Read more less

Betta Tilecare Tile & Grout Sealer waterproofs porous tiles and grout without leaving a slippery film coating, making it perfect for kitchens, bathrooms, and other tiled areas. Drying Time: Recoat: 15 minutes Full Dry: 24 hours Coverage: 1L covers 5-10m² Available Sizes: 1L, 4L, 300g Aerosol, 500ml Wheel Applicator, 750ml Trigger Application Method & Cleanup: Tools: Paint brush, roller, or pump spray Features: Water-based formula Clear penetrating finish Invisible, moisture-repellent coating Easy to use Proven technology Non-slip finish Preparation: Remove any silicone sealant strips and soap build-up. Clean mould off tiles and grout using Betta Tilecare Mould Rid™ or bleach. Rinse thoroughly with water after cleaning. Remove and patch all loose or missing tile grout. For improved results, add Bondall HydroCrete to the grout mix. Ensure the application area is dry for 12-24 hours before applying the sealer. For porous surfaces or after high-pressure washing, allow 3-4 days drying time before sealing. Application: Start from the top of the wall, applying Tile & Grout Sealer liberally over tiles and grout. Finish by applying the sealer to the shower base or floor. Ensure even coverage across all surfaces. Drying: Wait at least 15 minutes for the first application to react before reapplying. After the second application, wait another 15 minutes, then use a dry cloth to remove any excess from the tile surface. Allow 24 hours before using the sealed area. Tips & FAQs: Not for Water Holding Vessels: This product is not intended for waterproofing items like ponds or fish tanks. Test Before Use: Always test on a small, inconspicuous area to ensure it provides the desired result. Avoid Over-application: If the sealer runs or pools, wipe down with a clean, dry, low-lint cloth. Apply Evenly: Take care to apply evenly, especially on pitted surfaces. Pre-treat Stains & Mould: Ensure stains, moss, and mould are treated prior to sealing. Avoid Pooling: Do not allow the product to pool or over-apply on surfaces. Betta Tilecare Tile & Grout Sealer is a reliable and easy-to-use product for waterproofing and protecting your tiles and grout, providing long-lasting protection without altering the natural appearance of your surfaces.

Read more less

Glitz Furniture and Surface Polish Protective Shine 250g Bring dull furniture back to life with Glitz Furniture and Surface Polish. This quick spray-on polish lifts dust, reduces fingerprints, and leaves a smooth, protective shine that helps repel everyday grime. Ideal for busy homes and workspaces that want clean surfaces with a polished finish in minutes. Why you will love it Fast clean and shine: wipe away dust and light marks while restoring a bright finish. Protective layer: helps resist smears and fingerprints for surfaces that stay cleaner for longer. Versatile use: suitable for sealed timber furniture, laminates, vinyl, stainless steel, chrome, and sealed stone benchtops. Streak smart: designed to buff off clean so the surface looks fresh, not oily. Fresh finish: leaves a pleasant just cleaned feel. Best for Coffee tables, dining tables, sideboards, entertainment units Cabinet doors, shelves, desks, office furniture Appliance exteriors like stainless steel fridges and dishwashers Sealed stone and laminate benchtops How to use Shake well before use. Spray lightly onto the surface from about 20 to 25 cm, or spray onto a clean soft cloth. Wipe evenly to lift dust and light soil. Buff with a dry microfiber cloth to reveal a smooth, protective shine. Pro tips Test on a small hidden area first, especially on delicate or unusual finishes. For heavily soiled areas, clean first with a suitable surface cleaner, then polish. Use a dedicated microfiber cloth for polishing to avoid streaks. What to avoid Do not use on unsealed or raw timber. Do not use on floors, glass, fabrics, or screens. Avoid overspray near slippery walkways. Product details Brand Glitz Product Furniture and Surface Polish Protective Shine Format Aerosol spray Size 250 g Finish Smooth polished sheen Suitable Surfaces Sealed timber, laminate, vinyl, stainless steel, chrome, sealed stone benchtops Country of Use Australia Safety and storage Use in a well ventilated area and keep away from heat and open flames. Keep out of reach of children and pets. Store upright in a cool dry place. Frequently asked questions Will it make surfaces slippery It is not for floors. When used on furniture and benchtops as directed, buff to a dry finish to avoid slick residue. Can I use it on raw timber No. Seal or finish the timber first, then polish. Does it remove heavy stains It is a maintenance polish. For heavy grime, clean with an appropriate cleaner first, then apply this polish for protection and shine. Good to pair with Microfiber cleaning cloths for lint free buffing Everyday surface cleaner for pre clean on sticky or greasy areas Glues Australia keeps Australia together with trusted cleaning and care essentials. Order today for fast dispatch.

Read more less

Glitz Sugar Spray Soap Paint Prep and Surface Cleaner 450g Get surfaces paint ready with a fast acting sugar soap spray that cuts through everyday grime, grease, and fingerprints. Glitz Sugar Spray Soap makes prep quick and consistent so your paint, sealant, or wallpaper has a clean base for better adhesion and a smooth finish. Why you will love it Ready to use spray for quick coverage on walls, doors, trims, and tiles Lifts grease and grime to help paint stick and level more evenly Low streak formula wipes off clean and rinses easily Great for general household cleaning between projects Convenient 450 g can for easy storage in the toolkit or under the sink Ideal surfaces Painted plasterboard and brick Doors, skirting, window frames Tiles, laminate, vinyl, benches sealed against moisture Outdoor furniture and exterior trims that are sound and sealed Not recommended on Unsealed or raw timber Natural stone that is unsealed Waxed, oiled, or polished finishes Delicate plastics or lacquered metals that may mark How to use for paint prep Shake well. Protect floors and nearby furnishings. Spray a light, even coat on the area to be cleaned. Allow 1 to 2 minutes to penetrate built up grime. Wipe with a clean damp cloth or non scratch pad. Rinse the surface with clean water and allow to dry fully before sanding or painting. Tip: Always test on a small hidden spot first to confirm compatibility. General cleaning For everyday mess, spray, wipe, and rinse. For stubborn marks, repeat as needed. Product details Brand Glitz Product Sugar Spray Soap Paint Prep and Surface Cleaner Pack size 450 g Format Ready to use spray Appearance Clear liquid cleaner Suitable for Interior and exterior cleaning prior to painting Clean up Wipe and rinse with water Safety Wear gloves for extended use. Avoid contact with eyes and skin. Use in a well ventilated area. Do not inhale spray. Keep out of reach of children and pets. Do not mix with other cleaners or chemicals. Storage and disposal Store upright in a cool, dry place away from direct sunlight. Dispose of empty container in accordance with local regulations. Frequently asked questions Do I still need to rinse before paintingYes. Rinsing removes any remaining residue and helps paint adhere better. Can I use it on glossy trimsYes, but rinse well and allow to dry, then lightly sand if your paint system recommends it. Will it remove mould stainsIt removes general grime. For mould staining, clean first with a dedicated mould remover, then prep with this spray, rinse, and dry fully. Good to know Perfect as the first step in any repainting job Helps reduce fisheyes and adhesion issues caused by hidden grease Glues Australia ships fast Australia wide. Order today to get your prep done right.

Read more less

Dunlop Ready-To-Go Vinyl Flooring Spray Adhesive is a fast and tidy spray-on adhesive for installing vinyl sheet, vinyl tiles, and vinyl planks with vinyl backing over concrete, underlayment grade plywood, metal, and fibreglass. It delivers an even spray pattern, strong bond, and immediate traffic readiness once rolled. Why choose this adhesive Quick, clean spray application that saves time High initial grab for reliable placement Dry to touch in about 10 to 40 minutes Up to 3 hours open time once tacky Ready for immediate foot traffic after rolling Heat weld flooring 1 hour after installation Suitable with underfloor heating systems Water based acrylic blend with very low odour Suitable substrates Concrete, underlayment grade plywood, metal, and fibreglass. Use on vinyl-backed sheet, tiles, and planks. Not suitable for Cushion-backed flooring products. Surface preparation Ensure the substrate is flat, dry, and free from dust, oil, paint, old adhesive, wax, curing compounds, sealers, and hardeners. Lightly damp-mop concrete to remove fine dust before application. Correct surface imperfections before installation to avoid telegraphing. How to use Ventilate and mask the area to protect adjacent surfaces from overspray. Shake the can well and remove the blue safety tab. Hold the can upright 50 to 76 cm above the substrate and spray in smooth, even passes to achieve a uniform frosted look. Avoid heavy patches and overspray. Lightly re-spray missed areas if needed. Allow to dry until no adhesive transfers to the fingertips. Lay the vinyl and roll firmly within 1 hour using a suitable heavy roller to ensure full contact. The floor is ready for immediate use once rolled. Heat welding can commence after 1 hour. Key technical data Chemical type: water based acrylic blend Dry to touch: approximately 10 to 40 minutes Open time after tack: up to 3 hours Traffic allowance: immediate after rolling Underfloor heating: compatible Appearance when sprayed: milky white frost Storage and safety Store between 10°C and 50°C. Avoid freezing and direct sunlight. Pressurised dispenser. Do not pierce or burn the can, even when empty. Use in a well ventilated area and avoid contact with eyes and skin. Tip: Wipe any overspray from adjacent surfaces with a damp cloth before it dries.

Read more less

Dy-Mark MetalPro Rust Converter is a tannic acid based rust converter in a 350g aerosol, made for treating rusted steel and iron without stripping back to bare metal. One coat reacts with the rust and leaves a black, moisture-sealing layer that can sit under most paint systems.About the formulaThe tannic acid formula chemically reacts with the rust. It turns it into a black compound that bonds to the surface and helps keep moisture out, which slows further corrosion. It is phosphoric acid free. The spray can makes it quick to apply over fences, gates and other awkward shapes, and the result is a black finish.Where to use itIndoors: rusted machinery, equipment and metal furniture that you plan to repaint.Outdoors: rusted gutters, roofs, garden furniture, fencing, gates, trailers and other machinery and equipment.Suitable surfaces are rusted steel and iron (ferrous metals). It is not intended for clean, rust-free metal.How to use itWire brush, scrape or sand off loose rust, flaking paint, dirt, oil and grease so the surface is clean and dry. Work outdoors or in a well-ventilated area, and keep the surface cool and out of wind and direct heat. Shake the can well, then spray light, even coats over the rust until it is covered. For the best protection, overcoat within 3 months of treating the surface. Use Dy-Mark Primer first, then a Dy-Mark MetalPro Quick Dry topcoat colour. After use, invert the can and spray until only clear gas comes out, then wipe the nozzle tip clean. Follow the directions on the can.Important notesApply to rusted surfaces only, not as a rust-preventative coat on clean metal. It may not stop further rusting if applied over heavy, thick rust scale, so remove loose scale first. It is not recommended for permanent immersion in fresh or salt water. Do not apply zinc-rich primers or cold galvanising coatings over the converted surface. Test a small area first if you are unsure how it will suit your project.Specifications Brand Dy-Mark Product MetalPro Rust Converter (primer and sealer) Manufacturer part number 23803501 Size 350g aerosol can Colour Black finish Base / chemistry Tannic acid based, phosphoric acid free Application Aerosol spray Recommended overcoat window Within 3 months, with Dy-Mark Primer then MetalPro Quick Dry topcoat Use Interior and exterior rusted ferrous metal SafetyThis is a pressurised aerosol containing flammable solvents and propellant. Keep it away from heat, sparks, open flames and other ignition sources, and do not smoke while using it. Do not pierce or burn the can, even when empty. Use only outdoors or in a well-ventilated area, avoid breathing the spray, and wear gloves and eye protection. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Rust-Oleum LeakSeal Flexible Rubber Coating Spray in white is a ready-to-spray rubberised coating for sealing leaks and cracks around the home, supplied here as a single 340g aerosol can. It lays down a firm but flexible, watertight layer that helps keep out water, air and moisture, and it also protects the coated surface from rust. It suits quick repairs on gutters, roofing, flashing and ductwork without mixing, brushing or special tools.About the formulaA solvent-borne, hydrocarbon resin coating that sprays on and builds up to fill small gaps and cracks (the manufacturer lists gaps and cracks up to 6.35mm). It dries to a semi-smooth, firm finish that stays flexible and is designed not to sag or drip, so it holds its shape on sloped and vertical surfaces. Once cured it can be top-coated with latex or oil-based paints, which makes it easy to blend repairs into the surrounding colour scheme.Where to use itIndoors: sealing cracks and leaks in ductwork, pipework surrounds and other protected areas, with good ventilation while you spray.Outdoors: patching gutters, flashing, metal roofing, downpipes, masonry and concrete surfaces that need a flexible waterproof barrier.Suitable materials include metal, aluminium, galvanised metal, PVC, concrete, masonry, asphalt roofing materials, vinyl siding and fibreglass. Do a small test spray first if you are unsure about a surface.How to use it Prepare the surface by washing it with a detergent and water solution, rinsing well and letting it dry fully. Lightly sand glossy surfaces and wipe off the dust. Mask off nearby areas to protect against overspray. Spray outdoors or in a well-ventilated space, ideally when the temperature is between 10 and 32 degrees Celsius and humidity is below 65%. Avoid very windy or dusty conditions, and allow more drying time in cooler weather. Shake the can vigorously for about one minute once the mixing ball starts to rattle, and shake it often while you work. Do a test spray on cardboard to get a feel for the spray pattern, then hold the can 20 to 45cm from the surface and spray in short, even strokes. Apply a light first coat, then a second heavier coat for full coverage. Moving the can closer builds a thicker film. Some foaming or bubbling at first is normal and settles as the coating dries. After use, turn the can upside down and press the nozzle until only clear propellant sprays out. If the valve clogs, remove the spray tip and rinse it in mineral turpentine. Never push an object into the valve opening. Clean wet or dry coating with mineral turpentine or xylene. Important notesNot recommended for rubber surfaces or for surfaces that sit in continuous water immersion. Under the manufacturer's data, touch dry is about 2 hours at 21 to 27 degrees Celsius and 50% humidity, further coats can go on after 15 to 30 minutes, and you should allow 24 hours for a full cure and before top-coating. Cooler or more humid conditions will slow drying. This is not a fire or high-heat resistant coating. Shelf life is listed as 5 years.Specifications Brand Rust-Oleum Product LeakSeal Flexible Rubber Coating Spray Pack 1 x 340g aerosol can Colour White Base Solvent-borne, hydrocarbon resin Application Aerosol spray Gap and crack fill Up to 6.35mm Touch dry About 2 hours (21 to 27°C, 50% RH) Recoat 15 to 30 minutes Handle 2 to 3 hours Full cure / topcoat 24 hours Practical coverage About 0.37 to 0.46 m² per can at a thick 125 micron film, or about 0.74 to 0.93 m² per can at 62.5 microns (manufacturer figures allowing for 15% material loss) Paintable Yes, with latex or oil-based paints Use Interior and exterior SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Do not spray onto a flame. Contents are under pressure, so do not pierce or burn the can, even when empty. Use only outdoors or in a well-ventilated area, and avoid breathing the spray, mist or vapour. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Rust-Oleum LeakSeal Flexible Rubber Coating Spray in Black is a ready-to-use aerosol sealer for stopping leaks and sealing cracks around the home, workshop and site, supplied here as a single 340g can. It sprays on as a rubberised coating that builds a flexible, water-tight barrier over a wide range of common building surfaces, which makes it a quick fix for hard-to-reach or awkward spots where a caulking gun is difficult to use.About the formulaA solvent-based, hydrocarbon resin rubber coating that sprays on as a high-build film. It dries to a firm, semi-smooth black finish that stays flexible and is formulated not to sag or drip. The cured coating helps block moisture and protects against rust and corrosion, and it can be top-coated with acrylic (latex) or oil-based paints once cured.Where to use itIndoors: ductwork, pipes, air conditioner drip pans, vents and other protected areas where a flexible waterproof seal is needed (use only with good ventilation).Outdoors: gutters, downpipes, roof sheeting, flashing, skylight surrounds, metal sheds and buildings, and concrete or masonry surfaces where cracks or small holes let water in.Suitable surfaces include metal, aluminium, galvanised metal, PVC, concrete, masonry, asphalt roofing materials, vinyl siding and fibreglass. Always do a small test spray on an inconspicuous area first, particularly on plastics.How to use itPrepare the surface so it is clean, dry and free of loose material, dirt, grease and flaking paint. Do a test spray on a piece of cardboard first to get a feel for the spray pattern, then apply the coating over the leak or crack using even passes, following the directions on the can. Additional coats can be applied after 15 to 30 minutes if a heavier build is needed. Once cured, the surface can be top-coated with acrylic or oil-based paint. Use outdoors or in a well-ventilated area.Important notesThe coating is touch dry in about 2 hours, can be recoated with itself after 15 to 30 minutes, and can be top-coated after 24 hours (times based on roughly 21 to 27°C and 50% relative humidity, so allow longer in cool or humid conditions). It is not intended for surfaces under continuous water immersion. It is not rated as fire or high-heat resistant, and it is not a mould or mildew-resistant coating. Coverage depends on the film thickness applied: about 0.74 square metres per can at a thin film (62.5 microns) or about 0.37 square metres per can at a thicker film (125 microns), allowing for typical material loss. Shelf life is around 2 to 3 years.Specifications Brand Rust-Oleum Product LeakSeal Flexible Rubber Coating Spray Pack 1 x 340g aerosol can Colour Black Finish Semi-smooth, firm, flexible Base Solvent-based, hydrocarbon resin Application Aerosol spray Touch dry About 2 hours Recoat (with itself) 15 to 30 minutes Top-coat with paint After 24 hours Full cure About 24 hours Coverage per can About 0.74 m² at 62.5 micron, or 0.37 m² at 125 micron Paintable Yes, acrylic (latex) or oil-based paints Use Interior and exterior SafetyUse only outdoors or in a well-ventilated area, keep away from heat, sparks, flame and other ignition sources, and wear protective gloves, protective clothing, and eye and face protection. Store the can away from heat and do not store above 49°C. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Rust-Oleum LeakSeal Clear is a rubberised spray-on sealant that stops leaks and seals cracks in one easy aerosol, supplied here as a single 312g can. It lays down a flexible, water-tight coating over gutters, roofing, flashings, ducting and more, and the clear finish lets the original surface show through. It suits homeowners and maintenance tradies who need a quick, no-fuss repair.About the formulaA solvent-based, rubberised coating built on a hydrocarbon resin, delivered by a flammable propellant. It sprays on as a firm but flexible film that fills small gaps, cracks and holes (the manufacturer rates it for gaps up to about 6mm) and forms a barrier against water, air and moisture. It dries to a semi-smooth finish that does not sag or drip, helps protect the surface from rust, and can be topcoated with latex or oil-based paint once cured.Where to use itIndoors: ductwork, vents, pipes and other surfaces that need a flexible moisture seal.Outdoors: gutters, downpipes, roof flashings, metal roofing, sheds, vents and cracked masonry or concrete.Suitable materials include metal, aluminium, galvanised metal, PVC, concrete, masonry, asphalt roofing materials, vinyl siding and fibreglass. Test a small hidden area first on any surface you are unsure about.How to use itRemove all dirt and debris from the repair area. The manufacturer's technical data also advises washing with detergent and water, rinsing and letting the surface dry thoroughly, removing loose paint or old coatings, and lightly sanding glossy surfaces. Mask off surrounding areas to protect them from overspray.Apply outdoors or in a well-ventilated space, ideally between 10 and 32°C with humidity below 65%. Avoid very windy or dusty conditions.Shake the can vigorously for one minute after the mixing ball starts to rattle, and shake often during use. Do a test spray on cardboard to get a feel for the pattern.Hold the can about 20 to 45cm from the surface and spray in short, even strokes. Apply a light first coat, then a heavier second coat for full coverage. Moving closer to the surface builds a thicker film.Once the coating has fully cured, it can be painted with latex or oil-based paint if you want it to match the surroundings.Important notesDry to touch in about 30 minutes, with full cure in about 24 hours. Not recommended for rubber surfaces or for surfaces under continuous water immersion. It is not fire or high-heat resistant and is not rated as mould or mildew resistant. Coverage varies with surface porosity and how thick you apply it. Do not apply to hot surfaces.Specifications Brand Rust-Oleum Product LeakSeal Flexible Rubber Coating Spray Pack 1 x 312g aerosol can Colour Clear Base Solvent-based, hydrocarbon resin Application Aerosol spray Dry to touch About 30 minutes Full cure About 24 hours Maximum gap or crack size Up to about 6mm Application temperature 10 to 32°C Paintable Yes, with latex or oil-based paint Flexibility Remains flexible Use Interior and exterior SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Do not spray onto a flame. The can is pressurised: do not pierce or burn it, even when empty, and do not expose it to temperatures above 50°C. Use outdoors or with good cross-ventilation. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Soudal Genius Gun Gap Filling Expanding Foam is a one-handed, ready-to-use polyurethane foam for filling gaps, holes and joints while adding thermal and acoustic insulation, supplied here as a single 500ml can. The applicator trigger is built into the can, so there is no need to buy a separate foam gun, and the can can be put away part-used and picked up again on the next job.About the formulaA one-component, moisture-curing polyurethane foam with a stable, thixotropic body that stays where you put it. A built-in trigger and straw let you control the amount you dispense, and the resealable applicator keeps the can usable for up to 6 weeks after first use. Once cured it is light, sound-reducing and chemically inert, with minimal shrinkage and very little post-expansion. Manufacturer data lists a free-foamed density of about 25 kg/m³, sound insulation of 58 dB and thermal conductivity of 0.037 W/m.K. One 500ml can yields roughly 19 litres of free foam, or about 17 metres of joint fill. The foam is champagne in colour and is not UV resistant, so exposed foam needs a protective finish.Where to use itIndoors: filling gaps around door and window frames, sealing pipe and cable penetrations, closing holes and cavities in walls and ceilings, cutting down draughts and thermal bridges, and adding a sound-deadening layer.Outdoors: sealing gaps and openings in roof constructions and around frames and penetrations. Cover the cured foam with paint, plaster or sealant to protect it from UV light.Suitable materials include brick, concrete, masonry, timber, metals and most plastics, as well as most other common building materials. It does not bond to polyethylene (PE), polypropylene (PP) or PTFE. Run a quick adhesion test on unusual substrates first.How to use it Make sure surfaces are clean, dry and free of dust and grease, then lightly mist them with water to help the foam cure. Shake the can hard for at least 20 seconds, then open the cover and fold the tube out horizontally. Turn the can over and squeeze the trigger to dispense. Fill holes and cavities only about one third full, as the foam expands a lot as it cures. Shake the can again every so often while you work. For deep voids, build up in layers and moisten between each layer. When you finish, detach the bung, plug the nozzle with it, close the cap and store the can upright. Once fully cured, trim the foam with a sharp knife, then sand, paint, plaster or cover with sealant as needed. Important notesWipe off uncured foam straight away with Soudal Gun and Foam Cleaner or acetone, and test the cleaner on plastics, lacquer and paint first as they can be affected. Cured foam can only be removed mechanically or with a PU foam remover, and it must never be burned off. Use the product between roughly +5°C and +30°C. Skin forms in about 7 minutes and the foam can be cut after about 25 minutes (manufacturer figures, measured under standard test conditions, so real-world times vary with temperature, humidity and bead size). Cured foam is not UV resistant. Do not use it near electrical boxes or light fittings without checking the clearance guidance. Unopened cans keep for at least 12 months when stored upright in a cool, dry place at +5°C to +25°C.Specifications Brand Soudal Product Genius Gun Gap Filling Expanding Foam Manufacturer code 132272 Pack 1 x 500ml aerosol can Colour Champagne Base One-component polyurethane, moisture curing Application Built-in Genius Gun trigger applicator, one-handed Reusable Up to 6 weeks after first use Skin formation About 7 minutes Cutting time About 25 minutes Yield (500ml) About 19 L of free foam, about 17 m of joint fill Shrinkage after curing Under 3% Expansion after curing Under 1% Temperature resistance (cured) -40°C to +90°C, up to 120°C for a maximum of 1 hour Can size 65 x 65 x 315mm Use Interior and exterior (protect from UV) SafetyThis is a pressurised aerosol with flammable propellant and contains isocyanates. Keep it away from heat, sparks, flames and other ignition sources, do not smoke while using it, and never pierce or burn the can, even when empty. Wear gloves, safety glasses and protective clothing, and use only in well-ventilated areas. People already sensitised to isocyanates, or with asthma, eczema or skin problems, should avoid contact with the product. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Bostik Fill It Expanda Foam is a one-component, multipurpose polyurethane expanding foam for sealing, filling, bonding and insulating in a single step, supplied here in a 500ml aerosol can with a straw applicator. It expands to take up gaps and cavities of many sizes, then cures into an airtight, moisture-resistant seal that is designed not to shrink away from the surrounding surface.About the formulaA moisture-curing polyurethane foam that is ozone safe and has a mostly closed-cell structure, so it insulates against both heat and cold. Once cured it can be cut, sanded, plastered or painted to a neat finish. The included straw applicator lets you place foam into tight or awkward spots and apply it at any angle. The foam is not UV stable, so cured foam left exposed to sunlight should be painted.Where to use itIndoors: filling gaps and cavities around window and door frames, insulating around pipes, cutting down draughts, dust and noise, and adding a sound-absorbing layer or acoustic baffle.Outdoors: sealing openings in roof construction, filling larger holes and gaps in exterior walls, and helping to keep out insects and rodents (paint exposed cured foam).Suitable materials include concrete, brick, stone, plaster, timber and metal, as well as many plastics such as EPS, XPS, rigid PU foam and uPVC. It is not suitable for polyethylene (PE), polypropylene (PP), polycarbonate (PC), PMMA, PTFE, soft plastics, neoprene or bituminous surfaces.How to use itMake sure surfaces are clean, dry and free of dust, grease and loose material. Apply within the temperature range given on the can (+5°C to +35°C). Fit the straw applicator, shake the can well as directed on the label, and fill gaps only part-way, because the foam expands as it cures. Follow the label and Safety Data Sheet for cleaning up uncured foam. Once cured, trim any excess by cutting or sanding, then paint, plaster or finish as required.Important notesDo not use where the foam will sit under a permanent water load, or in cavities that are too dry to supply the moisture needed for curing. The foam is moisture-curing, so cure time varies with temperature, humidity and the surface. Typical values at 20°C and 60% relative humidity are a skin time of about 8 to 12 minutes and a cure of around 1 hour for a 30mm bead. Uncured foam can stick firmly to skin and clothing, so keep it off both while working.Specifications Brand Bostik Product Fill It Expanda Foam Multipurpose Polyurethane Expanding Foam Pack 500ml aerosol can with straw applicator Colour Off-white Base One-component, moisture-curing polyurethane foam Application Aerosol can with straw applicator Application temperature +5°C to +35°C Skin time About 8 to 12 minutes at 20°C and 60% RH Cure rate About 1 hour for a 30mm bead at 20°C and 60% RH Temperature resistance (cured) -40°C to +90°C continuous Use Interior and exterior SafetyUse in a well-ventilated area, keep away from heat, sparks and open flames, and do not pierce or burn the can, even when empty. Wear gloves, eye protection and protective clothing, and avoid breathing vapour or aerosol. If skin or hair is contaminated, remove affected clothing and flush with running water. Store in a well-ventilated place away from heat and dispose of the can through an approved waste facility. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Parfix Foam Fill Triple Expanding Filler is a polyurethane foam in a 750g aerosol can, made for packing out large gaps, cracks and cavities in and around the home. It expands well beyond its sprayed volume to fill irregular voids, then cures to a durable, water resistant foam that bonds to most common building surfaces.About the formulaA one-part polyurethane foam based on an isocyanate (MDI) prepolymer, supplied in a pressurised can. Once cured it is a firm, shrink resistant foam that can be cut, sanded and painted. Cured foam is not UV resistant, so exposed outdoor areas should be painted or covered.Where to use itIndoors: gaps around pipes and cable penetrations, cracks and holes in walls, and cavities around frames and fittings.Outdoors: holes and gaps in brickwork and other building surfaces, protected from direct sunlight once cured.Suitable for most building surfaces, including timber, metal, brick, stone and other masonry. Test on a small hidden area first if you are unsure about a particular material.How to use itWear gloves and safety glasses and work in a well ventilated area. Make sure surfaces are clean and free of loose material, dust and grease. Follow the directions printed on the can for shaking, nozzle attachment and application. Because this foam expands strongly, fill the gap only partly and allow room for growth rather than over-filling. Once fully cured, trim any excess with a knife or saw, then sand or paint as required. Uncured foam is best wiped off straight away with a suitable cleaner as directed on the can. Cured foam must be cut or sanded off.Important notesNot UV resistant, so paint or coat any foam that will be exposed to sunlight. Take care not to over-fill, as expanding foam can distort thin frames, door jambs and window casings. Keep the can away from heat, flames and sources of ignition. Check the can label for temperature range, cure times and further directions, as these are not covered in the product data we hold.Specifications Brand Parfix Product Foam Fill Triple Expanding Filler Pack 750g aerosol can Colour Off white / yellow Base Polyurethane (isocyanate-based) Application Aerosol can Finishing Can be cut, sanded and painted Shrink resistant Yes UV resistant No Use Interior and exterior SafetyUse only in well ventilated areas, wear gloves and eye protection, avoid breathing vapour and wash hands after use. People with asthma or sensitivity to isocyanates should take particular care. Do not puncture or burn the can, and keep it away from heat and ignition sources. Store upright in a cool, secure place away from children and check periodically for leaks. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Boyle Clear Spray Adhesive is a handy aerosol glue for bonding and mounting lightweight materials around the home, office and craft table, supplied here as a single 350g can. It goes on as an even spray and dries clear, so it suits neat jobs where you don't want visible glue lines.About the formulaA solvent-based spray adhesive. The supplied product data lists a light aliphatic petroleum solvent, dichloromethane and a hydrocarbon propellant. The nozzle spray gives broad, even coverage, and the adhesive is quick drying. Once cured it is clear, moisture resistant, UV/sunlight resistant and drillable. It is not solvent resistant and cannot be sanded.Where to use itIndoors: mounting prints, photos and artwork, laminating paper and card, and general craft, scrapbooking and office projects.Around the workshop: light bonding and mounting jobs on timber, metal, glass and fabric where a clear, even bond is wanted.Suitable materials include cardboard, cork, wood, paper, fabric, glass, prints and photographs, and metal. Plastics and foams are not listed by the manufacturer, so test a small hidden area first.How to use itShake the can well before use. Hold it roughly 20 to 25cm from the surface and spray an even coat. For a temporary bond, spray one surface only, let it dry, then press the surfaces together. For a permanent bond, spray both surfaces, wait until they turn tacky, then press them together firmly. Always test on an offcut or sample before coating the full surface. Work in a well-ventilated area and keep the nozzle clear of ignition sources.Important notesThis adhesive is designed for lightweight materials, not heavy or structural loads. It is not solvent resistant and not sandable. Solvent-based sprays can mark or soften some foams and plastics, so a test patch is a must. Full cure times are not published by the manufacturer, so allow plenty of time before putting the bond under stress.Specifications Brand Boyle Product Clear Spray Adhesive Size 350g aerosol can (single) Colour Clear Base Solvent-based (petroleum solvent, dichloromethane, hydrocarbon propellant) Application Aerosol nozzle spray Recommended use Bonding and mounting Dries clear Yes Moisture resistant Yes UV/sunlight resistant Yes Drillable Yes Solvent resistant No Sandable No SafetyUse only outdoors or in a well-ventilated area, and do not breathe the spray or mist. Wear protective gloves and eye protection, and wash hands and exposed skin after handling. Keep away from heat, sparks, open flames and hot surfaces, and don't spray near an ignition source. Do not pierce or burn the can, even when empty. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Crommelin Sprayable Exterior Grade Waterproofing is a rubberised, shake-and-spray waterproofing coating in a 400ml aerosol, made for outdoor areas that cop regular water and UV exposure. It is designed to seep into and seal leaks, cracks and small gaps, leaving a flexible, watertight film that suits quick repairs on roofs, gutters and similar exterior surfaces. This pack is the grey finish.About the formulaA rubberised coating delivered from a pressurised can, so there is no brush, roller or mixing involved. The manufacturer describes it as UV stable, weather resistant (it does not fade or yellow), permanently flexible and fast drying. It also helps protect the coated surface from corrosion and stops moisture getting through. Once cured it can be overcoated with most water-based (acrylic) paints.Where to use itIndoors: not intended for interior use. This is an exterior grade product.Outdoors: roofs and gutters, chimneys, skylights, block and brickwork, hoses, air conditioner drip pans and ductwork.Suitable surfaces listed by the manufacturer include metal (steel and aluminium), concrete and masonry, roofing materials, timber and particle board, PVC piping and fibreglass. The product has not been tested for use in potable water systems.How to use itSurfaces must be clean, sound and dry, and free of dust, grease, release agents, loose particles and other contaminants. Shake the can vigorously for one minute, and do a test spray on cardboard to get a feel for the spray pattern. Hold the can roughly 8 to 18cm from the surface and apply a thin first coat, which acts as a primer, then let it dry. Follow with a heavier coat, moving the nozzle a little closer to build a thicker film. For longer-lasting protection apply three to four coats, and for wider cracks and gaps keep adding coats until the cavity is filled. Apply to the positive side only (the side where water enters the substrate). Recoat once touch dry, which is about 20 to 30 minutes depending on thickness, weather and site conditions, and allow good airflow to help it cure.Important notesApply in temperatures of about 10 to 30 degrees C and avoid applying when humidity is high (the recommended maximum is 85% during application and cure). Avoid spraying in high wind or dusty conditions. Cold temperatures and poor airflow will lengthen cure times. It can be painted over after 24 hours. Full cure takes 48 hours, and the coating should not be exposed to water until then. Coverage depends on the shape and condition of the surface. Always do a small test area first.Specifications Brand Crommelin Product Sprayable Exterior Grade Waterproofing Pack 400ml aerosol can Colour Grey Type Rubberised waterproofing coating Application Aerosol spray (shake and spray) Recoat time About 20 to 30 minutes (touch dry) Paint over After 24 hours Full cure 48 hours Application temperature 10 to 30 degrees C Overcoating Most water-based (acrylic) paints Use Exterior SafetyKeep away from heat, sparks, flames and hot surfaces, do not spray onto a flame or ignition source, and do not pierce or burn the can, even when empty. Use in a well-ventilated area, avoid contact with skin, eyes and clothing, and wash hands before eating, drinking or smoking. Store out of direct sunlight and keep below 50 degrees C. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Crommelin Sprayable Exterior Grade Waterproofing is a ready-to-spray rubberised coating for sealing leaks and cracks on outdoor surfaces, supplied here as a 400ml aerosol can in white. It is made for spots that cop regular rain and sun, and it dries to a flexible, watertight layer that can be painted over with most acrylic paints.About the formulaA rubberised waterproofing coating in a pressurised can, so there is no brush, roller or mixing involved. The spray works its way into small holes and cracks to stop water getting through, helps block moisture penetration, and gives metal surfaces a barrier against corrosion. The manufacturer describes it as UV stable, weather resistant (it does not fade or yellow), fast drying and permanently flexible. The white finish suits light-coloured roofing and masonry.Where to use itIndoors: not intended for interior use, as this is an exterior grade product.Outdoors: roofs and gutters, chimneys, skylights, block and brickwork, and hoses, air conditioner drip pans and ductwork.Suitable materials include metal (steel and aluminium), concrete and masonry, roofing materials, timber and particleboard, PVC piping and fibreglass.How to use itMake sure the surface is clean, sound and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and any other contaminants. Crommelin recommends its Water Rinsable Degreaser for removing grease and oils. Shake the can well, then spray the area to be sealed following the directions on the can. Once the coating has dried it can be over-painted with most acrylic paints. Full application instructions are available on the Crommelin website.Important notesThis product has not been tested for use in potable water systems, so do not use it on drinking water tanks or pipework. It is an exterior grade coating and is not designed as an under-tile or interior wet area membrane. Check the can and the manufacturer's data sheet for drying and recoating times and for surface or ambient temperature limits before starting.Specifications Brand Crommelin Product Sprayable Exterior Grade Waterproofing Pack 1 x 400ml aerosol can Colour White Type Rubberised waterproofing coating Application Aerosol spray (shake and spray) Overcoating Can be painted over with most acrylic paints Use Exterior Pack dimensions Approx. 64 x 64 x 197 mm SafetyThe can may burst if heated. Use only in well-ventilated areas, avoid breathing the spray, and keep away from heat, sparks, flames and other ignition sources. Wear gloves and eye protection, and remove any contaminated clothing and splashes from skin straight away. Store in a cool, dry place out of direct sunlight, do not expose to temperatures above 50°C, and keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Designed to be used with Loxeal super glues: Speeds the cure of Istant 23 Fluid, Istant 25 Medium, Istant 27 High Viscosity and Istant 43 Speciale. Loxeal Activator 9 Cyanoacrylate Accelerator Spray 200ml Loxeal Activator 9 is an accelerator spray for cyanoacrylate super glues that cleans and degreases parts while slashing setting times. Sprayed onto one surface before assembly, it triggers cure in just 1–4 seconds – even on slow, dry or hard-to-activate substrates – and a treated surface stays active for up to 8 hours. It can also be misted over squeezed-out adhesive after assembly to fix the excess instantly. Supplied as a 200ml aerosol for fast, even coverage. Why choose Loxeal Activator 9? Cure in 1–4 seconds – turns slow joints into instant ones Cleans as it works – degreases parts in the same step 8-hour activation window – pre-treat parts ahead of assembly Fixes surplus glue – instantly sets excess adhesive outside the joint Convenient aerosol – quick, even application on parts of any shape Typical applications Speeding up cyanoacrylate cure on wood, porous and acidic surfaces Production assembly where consistent, rapid fixture times matter Cold or low-humidity conditions where super glue sets slowly Instantly curing glue fillets and squeeze-out for a tidy finish How to use Spray a light coat of Activator 9 onto one of the surfaces to be bonded. Allow it to dry for 20–30 seconds. Apply cyanoacrylate adhesive to the other surface and assemble the parts – cure takes effect in 1–4 seconds. To set surplus adhesive after assembly, mist it lightly with Activator 9. Usage notes Exact curing effect depends on the adhesive type, gap between parts and surface composition. Treated surfaces remain active for around 8 hours, so parts can be prepared in advance. Note that heavy over-application of activator can reduce ultimate bond strength on some joints. Specifications Chemistry Organic chemicals in solvent composition Appearance Colourless Viscosity (+25°C) 1–2 mPa·s Drying time (+25°C) 20–30 seconds Cure effect 1–4 seconds, adhesive and gap dependent Activation life on surface 8 hours Shelf life 12 months in original unopened packaging Pack size 200ml aerosol spray Important notes Solvent based aerosol – use in a well-ventilated area away from heat and ignition sources. Store in a cool, dry place below +20°C and do not refill containers with used product. Pair with Loxeal Istant cyanoacrylate adhesives for best results. Safety Consult the Safety Data Sheet (SDS) before use. Pressurised container – protect from sunlight and do not expose to temperatures exceeding +50°C. This information is provided as a general guide only. Always test on your specific materials and refer to the manufacturer's technical documentation before use.

Read more less

SikaBond High-Strength Foam Construction Adhesive 750 mL is a reliable one component foam construction adhesive dispensed from a can chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 750 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Sika High-Strength for your next project Everyday jobs often involve mixed materials and imperfect surfaces. SikaBond High-Strength Foam Construction Adhesive 750 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Fixing studs, battens, and sheets Filling small gaps while bonding Fast installation where speed saves labour Suitable surfaces The adhesive works well on the following surface types when properly prepared: Timber and masonry Concrete and fibre cement Many building materials except PE and PP Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of assemble parts within the open time to ensure a strong bond. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Expands slightly to fill gaps, then cures to a firm, high strength foam. Provides excellent initial grab and reduces the need for nails in many applications. Temperature and environmental performance Apply within the can's specified temperature range. Humidity supports foam curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured foam with the prescribed cleaner. Once cured, cut back mechanically. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store cans upright. Do not expose to heat. Observe transport and disposal rules for pressurised containers. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.

Read more less

Get fast and reliable adhesion with Bostik Quick Glu Instant Fix Bond Spray. This 25g spray adhesive provides a strong, clear and lasting bond suitable for a wide range of materials used in craft, home and office projects. Key Features Instant bonding for quick and easy use Dries clear for a neat and professional finish Acid free formula that resists yellowing over time Works on wood, metal, ceramic, leather, paper and many plastics (not suitable for polyethylene or polypropylene) Compact 25g size ideal for small jobs and easy storage How to Use Ensure surfaces are clean, dry and free from grease or dust. Shake the can well before each use. Hold the can 15 to 20 cm from the surface and apply a light, even coat. Wait a few seconds until tacky before joining the surfaces. Press firmly together and hold for a few seconds for best results. After use, clear the nozzle by spraying briefly while holding the can upside down. Recommended Applications Arts and crafts projects DIY home repairs Paper, cardboard, leather and wood bonding Quick fixes requiring a clear and clean finish Safety and Storage Use only in well ventilated areas and avoid inhaling vapours. Keep away from heat, sparks and open flames as the product is flammable. Store in a cool, dry place away from direct sunlight. Keep out of reach of children. Bostik Quick Glu Instant Fix Bond Spray delivers a convenient and efficient solution for fast bonding on a wide variety of materials.

Read more less

Bostik Spray Adhesive is a clear, fast-tack, multi purpose aerosol glue designed for quick and easy bonding of lightweight materials. Ideal for craft, school, office, and general household repairs where a neat, even spray is preferred. Why you’ll love it Fast tack with strong initial grab Clear, low-mess spray pattern for even coverage Adjustable bond: reposition briefly, then press firm Non-staining on most materials Great for large areas and edge-to-edge laminations Suitable materials Paper, cardboard, photos, craft foam, felt, fabric, foil, leather, cork, many plastics, wood, and light laminates. Always test on delicate or coated surfaces. Typical uses Mounting posters, photos, and presentations Craft projects and scrapbooking Attaching fabric or felt to displays Temporary positioning before stitching or stapling How to use Ensure surfaces are clean, dry, and free of dust or oil. Shake the can well before and during use. Hold 15–20 cm from the surface and spray a light, even coat. For temporary bonds, spray one surface only and join after 10–30 seconds tack time. For stronger bonds, spray both surfaces, allow to go tacky, then press together with firm, even pressure. Drying and cure Tack time: typically 10–60 seconds depending on coat weight and conditions Handling strength: a few minutes Full bond development: 24 hours Clean up While wet, wipe overspray from hard surfaces with a suitable adhesive remover or mineral turpentine, then wash with warm soapy water. Test cleaners on an inconspicuous area first. Good to know Clear finish when dry Best at room temperature with good ventilation Not recommended for high heat, heavy structural loads, or polyethylene and polypropylene unless tested Storage and safety Store upright in a cool, dry place away from heat and flame. Use only in well ventilated areas. Avoid inhalation and contact with eyes or skin. Keep out of reach of children. Press nozzle briefly upside down after use to clear. Specifications Format: Aerosol spray Colour: Clear Size: 350 g

Read more less

BBQ Tough Clean Grease & Grime Spray 400 g Bring your grill back to spotless condition with BBQ Tough Clean. This powerful, non-caustic formula is specially designed to lift away grease, fat, and charred food from BBQ plates, grills, and racks, giving you a cleaner and healthier cooking surface without harsh fumes. Key Benefits: Powerful cleaning: Penetrates and dissolves stubborn grease and grime. Spotless results: Leaves BBQ surfaces residue-free for safer cooking. Non-caustic & low fume: Safer to use around your outdoor cooking area. Cold application: Designed to work when the BBQ is cool (before use). Perfect For: Stainless steel and cast iron BBQ plates, grills, and racks Removing built-up food, grease, carbon deposits Deep cleaning before a big barbecue or regular maintenance How to Use: Make sure your BBQ is cold. Remove the racks, grills and plates if possible. Scrape off excess debris and wipe loose grease. Shake the can well and spray liberally onto the surface from upright position. Allow to sit at least 10 minutes (for tough grime, up to 2 hours), then wipe with a damp cloth or scouring pad. Rinse thoroughly with water and dry with a clean cloth. Optional: apply a light coat of cooking oil to surfaces to protect against corrosion. Important Safety & Usage Notes: Do not use on hot BBQs  Avoid spraying on painted, plastic or aluminum surfaces. If overspray lands on unintended areas, wipe off immediately and rinse. Not intended for use on exterior, non-cooking surfaces (use an exterior BBQ cleaner for those parts). Keep out of reach of children and pets. Use protective gloves and avoid inhaling fumes.

Read more less

SikaBond® SprayFix: The Ultimate Aerosol Spray Adhesive for Multipurpose Use High-Performance, Fast-Drying, & Repositionable Adhesive SikaBond® SprayFix is your go-to aerosol spray adhesive for both temporary and permanent bonding. With its high performance, low odour, and fast-drying time, it's designed for your convenience. Key Advantages: Easy to use Low odour Dries clear Fast drying time (approximately 2-4 minutes) High initial strength Contains no chlorinated solvents - suitable for indoor use Repositionable for 1-2 minutes Applications Include: Upholstery Floor Repairs Furniture Lamination Art and Crafts (e.g., mounting prints) Suitable Substrates: Felts and Fabrics Metals Foams Cork Most Plastics Rubber Gaskets Fibreglass Wood (e.g., plywood, particle board) How to Use: Ensure the surface is clean, dry, and free of dust and grease. Shake the can well before use. Hold the can approximately 80-100 mm from the surface and spray lightly. Allow a few minutes for drying. Packaging: Available in 150g and 350g aerosol cans. Color: White when applied, clear when dry. Cleaning of Equipment: After use, invert the can and press the tip until clear propellant comes out for cleaning. Uncured overspray can be removed with Sika® Colma Cleaner or another suitable solvent.

Read more less

Selleys KwikGrip Spray 350g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces Adhesive Mastery: Quick, Clear & Heat Resistant Discover the power of Selleys KwikGrip Spray 350g, a versatile adhesive spray that bonds instantly on contact. Ideal for both absorbent and non-absorbent surfaces, it offers a quick-drying and heat-resistant solution for a multitude of projects. Key Features: Versatile adhesive spray Durable bond Fast drying and dries clear Heat resistance up to 70°C Common Applications: Car upholstery repairs Fixing laminate on tables and bench tops Patching vinyl flooring Art and craft projects And many more... Compatible Materials: Laminated plastics Timber Craft foam Aluminium Leather Canvas Rubber Most plastics* How to Use: USE ONLY IN A WELL VENTILATED AREA. Shake the can well. Ensure surfaces are clean and dry. Hold the can 20cm away and spray surfaces evenly. For a permanent bond, spray both surfaces and wait until touch dry before pressing together. Clamp overnight for a firm bond. For a temporary bond, spray one surface and press together while still tacky. Limitations: Not suitable for bonding rough, ill-fitting surfaces or certain plastics like polyethylene or polypropylene. Refer to the guidelines for alternative solutions. Handy Tips: After use, clean the nozzle by inverting the can and spraying until clear

Read more less