Works on: Plastics (PP & PT)

A rapid dual-action adhesive system is specially designed to work on plastic to form resilient, invisible bonds in seconds. Recommended on: Plastic, Porcelain, Metal, Rubber, Leather, Wood, Paper. Properties: Bonds even difficult to bond plastics such as polyethylene (PE) and polypropylene (PP) Bonds in seconds Dries transparent Easy to open, self-piercing and anti-clog cap Suitable for use on most surfaces* Solvent-free * Except Styropor®, car glass and synthetic fibres. Use: Ensure surfaces to be joined are clean, completely dry and close fitting. Using the Surface Activator like a pen apply it to both surfaces and wait 60 seconds to dry. Twist the glue cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.

Read more less

Easy to use, fast setting adhesive system to repair ALL plastics. Features -Bonds ALL Plastics, including Polyethylene (PE) and Polypropylene (PP) -Easy to Apply -Dries clear for clean, neat results -Fast Bond: 2-30 seconds -No clamping necessary -No mixing required -self-piercing, clog-free cap on adhesive -Also bonds plastic to other surfaces: Metal, timber, china, rubber, leather Where can this product be used? -For interior projects and repairs -For fast & easy repair of household items made from plastic -Repair Toys & Games -Fix Car accessories -Repair Kitchen plastics and utensils -Repair Office items -Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet -Best results for Nylon items (e.g. car parts) are achieved without initial priming. Contact Selleys consumer advice if unsure of plastic type. -Not suitable for use on glass – we recommend Selleys Araldite Ultra Clear. What materials is this product suitable for? -ALL Plastics -Adhering Plastic to Metals China Rubber Leather How to use this product -Ensure the surfaces to be joined are close fitting, clean, dry and free of dust. -Using the primer pen, liberally coat plastic surface/s that are to be bonded. -Pierce seal at end of the adhesive tube by attaching nozzle and cap and turning clockwise. -Remove cap and apply a very small amount of glue to one surface only. Bring surfaces together and apply slight pressure. -The adhesive will grab within 2-30 seconds, depending on environmental conditions and materials being bonded. -Allow at least 30 minutes for sufficient bond strength for practical use. -Wipe tip of the tube, replace the cap and store upright in a dry cool place. Handy tips -If using on leather test on an inconspicuous area first as adhesive may cause leather to discolour or harden. -Not suitable to repair items that will contain hot liquids. -Best results for nylon items are achieved without Initial priming (e.g car parts). Contact Selleys Consumer Advice if unsure of plastic type. -Will also bond plastic to non-plastic surfaces (Metals, Timber, China, Rubber, Leather). Do not use primer on non-plastic surfaces. -After use, wipe excess product from the adhesive nozzle with a tissue dipped in nail polish remover. -For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. -In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in the hot soapy water. -Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use. Safetytips -Keep Out of reach of Children -Avoid contact with skin and eyes and avoid breathing in the vapour. -Bonds on contact. Should fingers stick together apply a solvent such as acetone (nail polish remover) to contact areas then wash with water. -Do not use solvents near eyes or open wounds. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use -Ensure caps are replaced and store in a cool dry place.

Read more less

For best performance, pair with this Loxeal product: Loxeal Cleaner 10 Degreaser: clean and degrease the plastics first for a stronger bond (no primer required). Loxeal Superlox Polyolefin Bonder 25ml Bi-Syringe (Single) Loxeal Superlox is a two-part acrylic adhesive developed to bond polyolefins, polypropylene (PP), polyethylene (PE), HDPE and LDPE, and other notoriously difficult low-surface-energy plastics, without primers, flame treatment or other expensive surface pre-treatments. This listing is for a single 25ml bi-syringe supplied with a mixing nozzle, dispensing the two components at a simple 1:1 ratio, so you can buy just what one job needs. It joins polyolefins to each other and to other plastics such as ABS and PVC, and to metals, producing structural joints with high shear and peel strength. Why choose Loxeal Superlox? Bonds the "unbondable", PP, PE, HDPE and LDPE plus other low-surface-energy plastics No primer or surface pre-treatment required, clean, apply, assemble Single 25ml bi-syringe with mixing nozzle, fresh adhesive for the job at hand Simple 1:1 mixing ratio through the supplied static mixing nozzle Structural performance, high shear and peel strength on plastics and mixed-material joints Also bonds polyolefins to other plastics (ABS, PVC) and to metals Typical applications Repairing and fabricating PP and PE components: tanks, housings, containers, piping and trim Joining polyolefin parts to dissimilar plastics or metal brackets and fittings Manufacturing and maintenance work on low-surface-energy plastic assemblies How to use Clean the surfaces to remove dust, oil and grease (for example with Loxeal Cleaner 10) and allow to dry. Fit the static mixing nozzle to the bi-syringe and discard the first few centimetres of extruded adhesive. Apply the mixed adhesive to one surface. Assemble the parts promptly and hold or clamp them without movement while the adhesive sets. Leave the joint undisturbed until fully cured before applying load. Cure times Fast curing at room temperature, parts typically fixture within minutes of assembly Allow 24 hours for full strength before placing joints under working load Refer to the Technical Data Sheet for precise fixture and cure data for your conditions Specifications Chemistry Two-part structural acrylic, polyolefin bonder Mixing ratio 1:1 by volume via static mixing nozzle Key substrates PP, PE, HDPE, LDPE and other low-surface-energy plastics; also ABS, PVC and metals Surface preparation No primer or pre-treatment required, clean and dry surfaces only Strength profile High shear and peel strength Pack size 1 x 25ml bi-syringe with mixing nozzle Buying more than one? If you use Superlox regularly, the Superlox trade pack of 10 x 25ml bi-syringes works out cheaper per syringe. Important notes Work at room temperature; low temperatures slow the cure Use each mixing nozzle for one continuous application, fit a fresh nozzle if work is interrupted Cured adhesive can only be removed mechanically Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and avoid skin and eye contact. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

A specially formulated adhesive and primer system that delivers a strong and shock-resistant bond on all plastics*, even polyethylene, polypropylene & ABS. Features Strong bond on all plastics*, even difficult rigid plastics like polyethylene, polypropylene & ABS Shock resistant, giving you a longer-lasting fix Fast setting in 30 seconds Also bonds plastic to non-plastic materials such as metals, timber, china, rubber, leather, and paper *Does not work on PTFE (Teflon) Where can this product be used? To repair plastic items made of PP, PE and ABS, e.g. plastic toys, office items, remote control What materials is this product suitable for? ALL plastics* including polyethylene, polypropylene and ABS Metals Timber China Rubber Leather Paper How to Use Use the primer pen to apply one coat on each plastic surface to be bonded. Primer pen will appear clear on the surface. Pierce seal at end of the adhesive tube by attaching nozzle & cap and turning clockwise. Remove cap and apply a small amount of glue to one surface only. Limitations: Not suitable for glass or foam, use Selleys Araldite Ultra Clear for glass or Selleys Power Grip Original for polystyrene foam.  Product only works on some rubbers and will not work on PTFE.  May cause leather to harden or discolour, test on an inconspicuous area first.

Read more less

Overview LOCTITE Super Glue All Plastics is a rapid dual-action adhesive kit featuring a precision super glue and a surface activator pen. Engineered to bond difficult plastics such as polyethylene (PE), polypropylene (PP) and PTFE, it forms clear, resilient bonds in seconds and resists water, most household chemicals and freezing temperatures. Ideal for repairs on toys, cameras, small automotive parts, wiper blades, rubber seals, figurines and other plastic components. Advanced bonding system: activator primes the surface; glue delivers high strength. Fuses hard-to-bond plastics: effective on PE, PP, PTFE and more. Fast & clear: sets in seconds, dries transparent for nearly invisible repairs. Durable: water-resistant and suitable for cold conditions. Surface Preparation Ensure both surfaces are clean, dry and close-fitting. Remove grease, oil, dust or loose particles. For best adhesion on very smooth plastics, lightly roughen with fine-grade sandpaper and wipe clean. Avoid use on soft foams, expanded polystyrene or highly porous materials. Always test on a small, inconspicuous area if unsure about compatibility. Application Instructions Prime with activator: Apply one or two thin coats to both bonding surfaces, ensuring full coverage. Re-cap the activator pen immediately. Allow to dry/react for 1–2 minutes. Apply adhesive: Place a minimal drop of glue on one surface only. Bring parts together immediately and hold firm pressure for at least 1 minute. Avoid shifting once contact is made. Cure: Leave undisturbed for 10 minutes. Full bond strength develops after 12–24 hours at room temperature. Coverage & Performance Only a thin film is required—one drop bonds most small mating areas. Initial handling strength is typically achieved within 5–30 seconds depending on substrates and conditions. Drying & Setting Time Initial set: 5–30 seconds* Handling time: ~1 minute Full cure: 12–24 hours Recommended conditions: 15–30 °C and ≥30% relative humidity *Setting and cure times vary with substrate, joint fit, temperature and humidity. Clean-Up & Storage Wipe nozzle to remove excess adhesive and replace caps immediately after use. Store upright in a cool, dry place away from sunlight and moisture. Do not refrigerate. Shelf life (unopened and properly stored): up to 18 months. Limitations Not recommended for glass, very flexible materials, soft foams or highly porous substrates. Not suitable for continuous water immersion or high-heat applications. For indoor use or dry environments; test before critical repairs. Safety & Handling Contains cyanoacrylate. Bonds skin and eyes in seconds . Avoid contact. Use in a well-ventilated area; consider gloves and eye protection. Refer to the Safety Data Sheet (SDS) for full details. Technical Data Product Type Two-part system: Activator + Cyanoacrylate Adhesive Substrates PE, PP, PTFE, many rigid plastics, rubber, selected metals Appearance Clear (dries transparent) Packaging Size 2 g adhesive + 4 ml activator Initial Set 5–30 seconds (substrate dependent) Full Cure 12–24 hours at ambient conditions Temperature Range Approx. −50 °C to +80 °C (typical for cured cyanoacrylates) Cleanup Mechanical removal once cured; avoid solvents on sensitive plastics What’s Included LOCTITE Super Glue (2 g) Surface Activator Pen (4 ml) Always follow on-pack directions. Performance will vary with materials, joint design and environmental conditions.

Read more less

Bostik Hard Plastics Glue is a clear, fast-setting adhesive designed for rigid plastic repairs around the home, garage, and workshop. It forms a strong, durable bond that resists impacts and everyday handling while drying clear for a neat finish. Best for ABS, PVC, acrylic, polycarbonate, polystyrene Household repairs, toys, car trim, appliance covers Small craft fixes and model making Not suitable for Polyethylene or polypropylene PTFE or silicone surfaces Surfaces that are oily, dusty, or wet Key features Clear finish that blends with most plastics Fast initial grab with strong final cure Impact and vibration resistant Precision nozzle for controlled application Surface preparation Ensure surfaces are clean, dry, and free from dust, grease, or release agents. Lightly roughen glossy plastic with fine sandpaper to improve adhesion, then wipe clean. How to use Test on a small hidden area first. Apply a thin, even layer to one surface. Avoid excess. Join parts immediately and hold firmly for 30 to 60 seconds. Allow to set undisturbed. Handling strength is typically reached within minutes. Full cure develops over 12 to 24 hours depending on temperature and humidity. Tips For tight fitting parts, less is more. A thin film gives the strongest bond. Use clamps or tape to maintain alignment while the adhesive sets. Cleanup Wipe fresh adhesive immediately with a suitable solvent on a cloth. Cured residue may need careful mechanical removal. Storage and safety Replace cap after use and store upright in a cool, dry place. Use in a well ventilated area. Avoid skin and eye contact. Keep out of reach of children.

Read more less

Gorilla Tough & Clear Mounting Tape is a clear double-sided tape that mounts in an instant, for a long-lasting, weatherproof bond. The crystal clear adhesive tape won’t yellow over time, and holds up to 6.8kg! (15 pounds) Gorilla Tough & Clear Mounting Tape is perfect for indoor and outdoor projects and sticks to smooth and rough surfaces. Completing DIY projects is easy with this tough, double-sided tape. Mount, build, and repair for a perfect finish, every time. Features 6.8KG Strong Hold - Sticks to smooth and rough surfaces.* Weatherproof - For indoor and outdoor use. Crystal Clear Adhesive - Won't yellow over time. Double Sided Tape - coated with adhesive on both sides for easy hanging. Bonds - Plastic, Metal, Wood, Glass, Brick, Ceramic, Stone & More! *weight limits may vary depending on surface texture, porosity and flatness of surface. Both surfaces must be completely flat to make full contact with adhesive. Is Gorilla Mounting Tape permanent? Yes. Once Gorilla Mounting Tape is used to mount an object, it is meant to be held in place permanently, and not be removed. How much weight will Gorilla Mounting Tape hold? Gorilla Black Mounting Tape will hold up to 30 (13.6KG) pounds per project. How do I remove Gorilla Mounting Tape’s liner? Once Gorilla Mounting Tape is pressed onto the surface of the object to be held, remove the liner by peeling it from a corner of the tape. This can be done by using a fingernail or similar object to separate the liner from the tape. How do I remove Gorilla Mounting Tape? Gorilla Mounting Tape is a permanent tape. Once applied, it can be difficult to remove, and can damage surfaces if the objects are pulled away from the surface.  If Gorilla Mounting Tape isn’t exposed and cannot be reached by hand between the mounted object and the surface, a prying motion on the object from one corner can sometimes remove it from the surface. Please note that damage to the surface can occur.  If Gorilla Mounting Tape is exposed and within reach between the mounted object and the surface, pull the tape parallel to the surface (or vertically downwards) to remove it from the object. How much Gorilla Mounting Tape should I use on my project? Use four inches of Gorilla Heavy Duty Mounting Tape per pound of weight being held.

Read more less

Use before bonding polyolefins with a Loxeal super glue: Prime the surface, then bond with Istant 23, Istant 25, Istant 27 or Istant 43. Loxeal Primer 7 Polyolefin Primer 20ml Loxeal Primer 7 is a solvent-based surface primer that makes the “unglueable” plastics glueable. Applied before a cyanoacrylate super glue, it raises the surface energy of polyethylene (PE), polypropylene (PP), thermoplastic rubbers, EPDM, PTFE and silicones, transforming bond strength on these notoriously low-energy materials. It dries in seconds, is fluorescent under blue light so coverage can be checked, and is recommended for use with Loxeal Istant 34 and other ethyl cyanoacrylate adhesives. Supplied in a 20ml bottle. Why choose Loxeal Primer 7? Unlocks polyolefins – makes PP, PE, PTFE, EPDM and silicone bondable with standard super glues Fast and simple – brush on a thin coat, wait a few seconds, then glue as normal Verifiable coverage – fluoresces under a blue lamp for quality control Long working window – primed surfaces stay active for up to one hour Ultra-thin, fluid consistency – roughly 1.5 mPa·s for even wetting of the surface Typical applications Bonding polypropylene and polyethylene parts, containers and housings PTFE, silicone rubber and EPDM components that resist ordinary adhesives Thermoplastic rubber grips, seals and trims Production and repair work on low surface energy plastics How to use Ensure surfaces are clean and dry. Brush a thin coat of Primer 7 onto the surfaces to be bonded and let it dry for a few seconds. Apply your cyanoacrylate adhesive and press the parts together – handling strength develops within seconds. Bond within one hour of priming for best results; reapply primer if more than eight hours pass. Reseal the bottle immediately after use. Usage notes Primer 7 is intended only for difficult, low surface energy materials – do not use it on substrates that bond readily without priming. Best adhesion is achieved when parts are joined within an hour of application. Specifications Chemistry Aliphatic amine in organic solvent Appearance Colourless; fluorescent under blue light Viscosity (+25°C) 1.5 mPa·s Specific weight (+25°C) 0.7 g/ml On-part life Bond within 1 hour; reapply after 8 hours Shelf life 1 year in original unopened packaging at +25°C Pack size 20ml bottle Important notes Solvent based – use in a well-ventilated area away from ignition sources. Store in a cool, dry place below +20°C and do not refill containers with used product. Seal the bottle immediately after each use to preserve the contents. Safety Consult the Safety Data Sheet (SDS) before use and wear suitable protection when handling. This information is provided as a general guide only. Always test on your specific materials and refer to the manufacturer's technical documentation before use.

Read more less

One On One Heavy Duty Double Sided Sealing Tape from CAgroup (Consolidated Alloys) is a butyl rubber tape that sticks and seals in a single step, supplied here as a 48mm x 5m roll. It is aimed at builders, roofers and DIYers who need a tacky, water-resistant seal between building materials, membranes and sheeting without mixing, gunning or waiting for anything to cure.About the formulaThe tape is a highly water-resistant butyl rubber sealant supplied on a siliconised kraft paper release liner, which peels away cleanly so the tape is easy to handle and position. The soft butyl adhesive conforms to rough and textured surfaces, so it can follow uneven substrates and fill small surface irregularities as it is pressed into place. It is described by the manufacturer as suitable for joining, sealing, waterproofing and absorbing vibration.Where to use itIndoors: joining and sealing builders film, polythene sheeting and sisalation foil, and damping vibration or noise on audio parts and similar fittings.Outdoors: sealing joints for waterproofing in construction and joining and sealing membranes on building sites.Suitable materials include glass, metal, wood, rendered concrete and plastics, including both high and low energy surfaces. Always test a small area first on unfamiliar plastics or coated surfaces.How to use itMake sure the surfaces are clean, dry and free of dust, oil, grease and loose material. Measure and cut the tape to length, peel back the kraft liner as you go, and position the tape without stretching it. Press the tape down firmly along its full length, then bring the second surface or membrane into place and apply even pressure so the butyl makes full contact. If the substrate is very rough, press harder or work the tape in so it can conform to the texture.Important notesButyl tape is a soft, pressure-sensitive sealant, not a structural adhesive, so do not rely on it alone to carry heavy loads. Butyl rubber can be softened by some solvents, so keep it away from solvent-based products unless you have checked compatibility. The manufacturer has not supplied application temperature limits, service temperature range, thickness or standards compliance figures for this size, so none are stated here. If you need compliance with a specific standard or approval (for example for damp-proof courses), confirm it with CAgroup before use.Specifications Brand CAgroup (Consolidated Alloys) Product One On One Heavy Duty Double Sided Sealing Tape Size 48mm wide x 5m long roll Pack Single roll Base Butyl rubber Format Double sided tape with siliconised kraft paper release liner Application Hand applied, press into place Use Joining, sealing, waterproofing and vibration absorption SafetyAs general good practice, keep the tape away from heat and open flame, avoid prolonged skin contact with the adhesive, wash your hands after handling, and store the roll in a cool, dry place out of direct sunlight and away from children. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Gorilla Ultimate Tape is the brand's toughest cloth tape, supplied here as a single black 48mm x 18.2m roll for hauling, strapping, patching, bundling and lifting jobs around the home, workshop and site. Gorilla rates it at five times the tensile strength of its original Gorilla Tape. It is designed for heavy loads rather than everyday taping.About the formulaThe tape combines a weather-resistant outer shell, a high tensile cloth layer and a double-thick, rubber-based adhesive. The thick adhesive layer bites into smooth, rough and uneven surfaces. The reinforced cloth is strong enough that you cut it with a utility knife or scissors instead of tearing it by hand. Gorilla states that a single loop of tape can hold more than 360kg. That figure comes from independent tensile testing in a controlled environment with specific preparation, so allow a generous safety margin on real jobs.Where to use itIndoors: bundling pipes, cables, timber and offcuts, patching and reinforcing packaging or equipment, and strapping loads in the workshop or garage.Outdoors: hauling and lifting loops, securing tarps and covers, and patching or holding items in damp or changeable weather, thanks to the moisture-resistant, weather-resistant shell.Suitable materials include wood, stone, stucco, brick, metal and vinyl. The manufacturer also states the adhesive sticks to most plastics, including polyethylene and polypropylene. It is not recommended on materials with a high oil or plasticiser content, such as EPDM rubber or PVC. Test a small area first on any surface you are unsure about.How to use itMake sure the surface is clean, dry and free of dust, oil and grease. Cut the tape to length with a utility knife or scissors. Apply it carefully and smooth out any air pockets or ridges as you go. For lifting, hauling or bundling loops, keep the tape free of creases and folds, because these can reduce its strength. Use extra wraps or additional tape for heavier loads. Apply at room temperature where possible. Store the roll in a cool, dry place out of direct sunlight.Important notesThis is not a hand-tear tape, so keep a knife or scissors handy. Take care when handling heavy loads, because serious injury can occur if a load or loop fails. Do not use it as a substitute for rated lifting or rigging equipment where safety depends on the load rating. Do not use it on PVC or EPDM rubber, as the adhesive is not suited to these. Gorilla's published guidance for the Ultimate tape is for application between about 4°C and 49°C, with continuous service up to about 65°C.Specifications Brand Gorilla Product Ultimate Tape Pack 1 roll Size 48mm wide x 18.2m long Colour Black Construction Weather-resistant shell, high tensile cloth, double-thick adhesive Adhesive Rubber-based Application Hand applied, cut with a utility knife or scissors Roll size (approx.) 130mm diameter Moisture resistant Yes Use Interior and exterior SafetyKeep it away from children and animals. Use caution when cutting with a knife and when handling heavy loads. Store it in a cool, dry place out of direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.

Read more less