Low Temperature Resistant

Shower Plug Penetrating Sealer 220mL Stop leaks without removing tiles. Shower Plug penetrates into masonry surfaces and forms a water repellent barrier that fixes and prevents leaks in showers, balconies and other masonry areas. One application lasts 10 years. Penetrates grout, tile and masonry to block water at the source No tile removal required Indoor and outdoor use, friction and UV resistant Does not change surface appearance or make it slippery Makes surfaces easier to clean and helps prevent mould Breathable seal allows trapped moisture below tiles to escape Seals gaps up to 1 mm. For wider cracks, repair with grout or silicone first Why Shower Plug Released in 1992, Shower Plug is the original Australian penetrating sealer technology for leaking shower repair. It delivers cost and time efficiency with proven longevity and reliability. Fixing a leaking shower, methods compared Item Tile and membrane removal and replacement Shower Plug 220mL Typical cost > $1000 $55 Time required > 5 days 30 minute application, ready to use in 12 hours Skill level Trade DIY Effective lifespan Average 5 years 10 years minimum Coverage Approx. 7 m² per pack (about 75 ft²), depending on porosity. Where to use Grout Tiles including ceramic, porcelain, marble, glazed or unglazed, terrazzo, slate, terracotta and more Concrete and masonry Bare plaster. If painting later, use a solvent primer undercoat after treatment Showers, balconies, other tiled or masonry wet areas Not suitable for Plastics and polymers such as polyurethane and polycarbonate Glass Metal Wood Painted surfaces How to apply Ensure the surface is clean and dry. Using a natural bristle brush, apply the first coat evenly. After 5 minutes, apply a second coat. Five minutes after the second coat, wipe away any remaining excess from the surface. Allow to cure. Area is ready to use in 12 hours. Important: Wipe the final coat off within 5 minutes. If left to dry on the surface, a white residue may appear. Remove any residue with turpentine. Good to know Gives off a mild solvent type odour during application and cure. This fades by the end of curing. Does not affect clothing under normal use. Safer to handle than household paint when used as directed. Always use protective gear and ventilation. Specifications SKU SP220ML Category Shower Plug Pack size 220 mL Coverage Up to 7 m² per pack Weight 0.25 kg Dimensions 7.5 cm x 7.5 cm x 8 cm Finish Invisible. No change to surface look or feel Use areas Showers, balconies, tiled and masonry wet areas Lifespan 10 years Directions recap Two coats applied 5 minutes apart. Wipe off excess 5 minutes after second coat. Ready to use in 12 hours. What you get Shower Plug 220 mL bottle Simple step by step instructions Shower Plug gives you the solution.

Read more less

Selleys Auto Fix Auto Sealant Translucent 100 mL Keep water out and vibrations at bay with a clear automotive sealant that bonds fast and stays flexible. Selleys Auto Fix Auto Sealant is a 100 percent neutral cure silicone designed for cars, caravans, and general automotive sealing where a durable waterproof finish is essential. Why you will like it 100 percent neutral cure silicone Versatile general purpose sealant for automotive use Waterproof seal that resists vibration and temperature extremes UV and weather resistant for long lasting performance Skins in 5 minutes, set to touch in 30 minutes, full cure in 24 hours Where to use it Adheres to most auto and caravan materials, including: Glass and painted surfaces Fiberglass and most plastics Trim components Most rubbers Typical applications Sealing around lights, windows, and trim Gasket style sealing where a flexible waterproof joint is required General leak prevention and small gap sealing in automotive and caravan fittings Directions Preparation: Clean surfaces so they are free of dust, oil, and moisture. Wipe with mineral turpentine and allow to dry. Cut and load: Remove cap, unscrew nozzle, remove seal. Refit nozzle and cut at a 45 degree angle to the desired bead size. Apply: Squeeze the tube with steady pressure to lay a continuous bead. Smooth with a gloved finger before the sealant skins. Clean up: Before cure, clean tools and excess with mineral turpentine. Once cured, remove by cutting or scraping. After use: Replace cap. Let cured material in the nozzle be removed before next use. Handy tips Mask edges for neat joints. Remove tape before skin forms. Work within the skin time to achieve a smooth finish. Limitations Not recommended for Natural rubber, NBR, or Chloroprene Neoprene Technical details Technology 100 percent neutral cure silicone Colour Translucent Packaging Tube 100 mL Density 1.02 g per mL Application temperature -20°C to 50°C Skin time 5 minutes Shore A hardness 25 Elongation at break 370 percent Movement capability 25 percent Service temperature -40°C to 180°C VOC 26 g per L Clean up and storage Clean uncured sealant with mineral turpentine Store below 30°C in a cool dry place Use within 24 months from date of production Safety: Refer to the product SDS for handling and first aid information. Use in a well ventilated area and keep out of reach of children.

Read more less

Improve energy efficiency and protect your pipes with K-Flex Self Adhesive Pipe Insulation Tape. Designed to prevent heat loss and condensation, this high quality insulation tape provides a secure, long lasting seal around hot and cold water pipes, air conditioning lines, and refrigeration systems. The self adhesive backing makes installation quick and mess free, ensuring a tight bond without the need for extra adhesives or fasteners. Key Features Reduces heat loss in hot water and heating pipes Prevents condensation and moisture build up on cold pipes Self adhesive for easy and fast installation Durable closed cell elastomeric foam construction Excellent thermal insulation and flexibility Suitable for copper, steel, and plastic pipes Resistant to mould, mildew, and environmental wear Best For Insulating hot and cold water lines Preventing energy loss in heating systems Air conditioning and refrigeration pipework Reducing condensation on exposed pipe surfaces Improving system efficiency in residential and commercial buildings Product Specifications Brand K-Flex Product Self Adhesive Pipe Insulation Tape Material Elastomeric foam Adhesive Type Pressure sensitive acrylic adhesive Colour Black Temperature Range -40°C to +85°C Applications Thermal insulation, condensation control, energy saving Water Absorption Low, closed cell structure resists moisture How To Use Ensure the pipe surface is clean, dry, and free from dust or oil. Peel away a section of the backing paper to expose the adhesive. Wrap the tape tightly around the pipe, overlapping each layer by at least 10 mm. Press firmly to ensure full adhesion and an airtight seal. Trim any excess tape with a sharp blade for a clean finish. Tips For maximum efficiency, insulate all exposed pipe joints and fittings. Use in conjunction with K-Flex insulation tubing for full coverage. Store in a cool, dry place when not in use.  

Read more less

DETA Flame Retardant PVC Insulation Tape is a 600V-rated electrical tape for domestic and industrial wiring jobs, supplied here as a value 10-pack of assorted colour rolls. Each roll is 18mm wide and 20m long, so you can colour-code and insulate across a whole job without running short.About the tapeA soft, flexible PVC film with a pressure-sensitive adhesive, made for dependable adhesion and electrical insulation. The tape is flame retardant, lead free, RoHS approved and UL listed. It is only 0.18mm thick, which keeps wrapped joints neat, and it handles cold conditions and UV exposure, so it holds up both inside and out.Where to use itIndoors: insulating and bundling wiring in switchboards, light fittings and appliances, and colour-coding conductors and circuits.Outdoors: protecting and insulating cable joints exposed to sun, weather and cooler conditions.Suited to wrapping over cable insulation, conductors and wiring harness joints for electrical insulation, identification and general protection. Moisture sealing is part of the tape's rated performance.How to use itIsolate the power before you start. Make sure the area to be wrapped is clean and dry. Start the wrap a little beyond the section to be covered, then apply the tape with a slight stretch. Overlap each turn by about half the tape width for even coverage, and finish a little past the end of the joint. Press the end down firmly so it stays in place, then cut the tape rather than tearing it.Important notesThis is an insulating tape rated to 600V. Do not use it above that voltage, and do not rely on it as a replacement for approved connectors or fittings. Electrical work should be carried out by a licensed electrician where the law requires it. DETA lists its PVC tape range as suitable up to 80°C. Keep the tape away from sources of heat that exceed this rating.Specifications Brand DETA Product Flame Retardant PVC Insulation Tape Pack 10 rolls, assorted colours Roll size 18mm wide x 20m long Thickness 0.18mm Material PVC Maximum voltage 600V Flame retardant Yes Standards and approvals UL listed, RoHS approved Resistance Cold and UV resistant Moisture sealing Yes Use Indoor and outdoor SafetyAlways switch off and isolate power before taping any wiring. Store the rolls in a cool, dry place out of direct sun, and keep them out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

The DETA Black Flame Retardant PVC Tape is a general-purpose electrical insulation tape for tidying, insulating and protecting wiring, supplied here as a single 18mm x 20m roll. It suits both household and industrial electrical jobs, and the flame retardant grade gives extra peace of mind on cable work around the home, workshop or site.About the tapeA black PVC film tape with a 0.18mm thickness, designed to grip well and insulate electrical connections up to 600V. It is lead free, UL listed and RoHS approved, and it is built to handle weather exposure, with resistance to UV and cold for reliable performance outdoors. The flame retardant formulation sets it apart from DETA's standard insulation tape, and it also helps seal out moisture.Where to use itIndoors: insulating and wrapping wire joins, bundling and colour-coding cable runs, and protecting wiring in switchboards, appliances and workshops.Outdoors: wrapping and protecting cable connections exposed to sun, rain and cooler conditions, such as garden lighting, outdoor fittings and site wiring.Designed for use on electrical wire and cable. Always follow local electrical regulations, and have licensed work carried out by a qualified electrician where required.How to use itMake sure the wire or cable surface is clean and dry, and that the power is isolated before you start. Begin the wrap slightly beyond the area to be covered, then apply the tape with light tension and overlap each turn so there are no gaps. Finish by pressing the end down firmly so it stays in place.Important notesRated for electrical insulation up to 600V. Do not use it beyond its rated voltage. It is intended as insulation and protection for wiring and is not a substitute for approved connectors or fittings where those are required. Flame retardant does not mean fireproof.Specifications Brand DETA Product Black Flame Retardant PVC Tape Pack 1 roll, 18mm x 20m Colour Black Material PVC Thickness 0.18mm Maximum voltage 600V Flame retardant Yes Moisture sealing Yes Approvals UL listed, RoHS approved, lead free Use Indoor and outdoor SafetyAlways isolate the power before working on electrical wiring and follow local electrical regulations. Keep out of reach of children and store the roll in a cool, dry place away from direct heat. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

DETA Insulation PVC Tape is a general-purpose electrical tape for domestic and industrial wiring jobs, supplied here as a handy 5 pack of assorted colour rolls, each 18mm wide and 20m long. The mixed colours make it easy to tidy up, identify and insulate separate runs, and the soft PVC film conforms well around cables and joins.About the formulaA PVC film tape with a pressure-sensitive adhesive, designed to grip well and insulate electrical connections up to 600V. It is lead free, RoHS approved and UL listed, and the film is only 0.18mm thick, so it wraps neatly. It resists cold and UV exposure, seals out moisture and holds up well in the weather. Note that this is a standard insulation tape and is not flame retardant.Where to use itIndoors: insulating and bundling low voltage and mains-rated wiring joins, tidying cable runs, and general repairs around the home, workshop or site.Outdoors: protecting and insulating exposed cable joins and connections, where its cold and UV resistance and moisture sealing help it cope with the elements.Suited to wrapping over PVC and other cable insulation, bare conductor joins (once connected and made safe) and common electrical fittings. For fixed wiring, always follow local regulations and use a licensed electrician where required.How to use itMake sure the circuit is isolated and the surface is clean, dry and free of oil, grease and dust. Start the tape on the cable, then stretch it lightly as you wrap, overlapping each turn so the join is fully covered and the end sits flat. Press the tail down firmly. Cut the tape rather than tearing it so the end does not lift.Important notesRated for electrical insulation up to 600V only. Not a flame retardant tape, so choose a flame retardant product where one is specified. Do not use it as a substitute for correct connectors, enclosures or approved repairs on damaged cable. Colours in the pack are assorted, so the mix may vary.Specifications Brand DETA Product Insulation PVC Tape, Assorted Pack 5 rolls Roll size 18mm x 20m Thickness 0.18mm Colour Assorted Material PVC Maximum voltage 600V Flame retardant No Moisture sealing Yes Approvals UL listed, RoHS approved Use Indoor and outdoor SafetyAlways isolate and de-energise circuits before taping, and keep the work area dry. Keep the tape out of reach of children and store it in a cool, dry place away from direct sunlight and heat. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

DETA Insulation PVC Tape in white is a general-purpose electrical tape for household and industrial wiring jobs, supplied here as a handy five-roll pack. Each roll is 18mm wide and 20m long, so there is plenty on hand for repairs, cable bundling and colour-coding whether you are working at home or on site.About the tapeA soft, flexible PVC film tape with a self-adhesive backing, designed to grip well and provide electrical insulation up to 600V. At 0.18mm thick, it is made to cope with cold conditions and sunlight exposure, and it is lead free, RoHS approved and UL listed.Where to use itIndoors: insulating and protecting wire joins, bundling and tidying cable runs, and marking or colour-coding circuits in switchboards, appliances and general wiring.Outdoors: wrapping and protecting wiring exposed to weather, as the tape resists UV and cold and seals out moisture.Suitable for general electrical insulation and cable identification on wires, cables and connections. White is useful where a visible, distinct colour code is needed.How to use itMake sure the wire or joint is clean and dry, and that the power is isolated before you start. Begin wrapping slightly beyond the area to be covered, overlap each turn as you go and apply light, even tension so the tape conforms to the shape. Finish past the end of the joint and press the tail down firmly. Cut the tape cleanly rather than tearing it.Important notesThis tape is not flame retardant, so choose a flame-retardant tape if your job requires one. It is rated for electrical insulation up to 600V, so do not use it where higher voltages are involved. Always isolate power and follow local electrical regulations, and have a licensed electrician carry out any work that legally requires one.Specifications Brand DETA Product Insulation PVC Tape Pack 5 rolls Roll size 18mm wide x 20m long Thickness 0.18mm Colour White Material PVC Maximum voltage 600V Flame retardant No Moisture sealing Yes Compliance UL listed, RoHS approved, lead free Use Indoor and outdoor SafetyIsolate and test that circuits are dead before wrapping any electrical connection. Keep out of reach of children and store the rolls in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

DETA Black Insulation PVC Tape is a dependable general-purpose electrical tape for insulating, protecting and tidying wiring, supplied here as a handy five-roll pack so you always have a spare on the toolbelt. Each roll is 18mm wide and 20m long, a standard size that suits household repairs and everyday trade work.About the tapeA soft, flexible PVC tape with a good grip on clean surfaces and a thickness of 0.18mm. It provides electrical insulation up to 600V and is lead free, UL listed and RoHS approved. The manufacturer also describes it as cold and UV resistant with good weatherability, and it is moisture sealing once wrapped.Where to use itIndoors: insulating and joining wire connections, bundling and tidying cable runs, and making general electrical repairs around the home, workshop or site.Outdoors: covering and protecting wiring that is exposed to sunlight, cold and damp, thanks to its UV and cold resistance and moisture sealing.Suitable for use on electrical wiring and cable insulation in domestic and industrial settings. Black is a neat, discreet choice for most cable work.How to use itIsolate the power and make sure the wiring is safe to work on. Wipe the surface clean and dry, then start wrapping with the tape lightly stretched. Overlap each turn so there are no gaps, and finish by pressing the end down firmly so it sits flat. Cut the tape rather than tearing it for a cleaner finish.Important notesThis tape is not flame retardant, so choose a flame retardant tape where that is required. It is rated for electrical insulation up to 600V, so do not use it beyond that rating. Always follow local electrical rules and have fixed wiring work completed by a licensed electrician where required.Specifications Brand DETA Product Insulation PVC Tape Pack 5 rolls Roll size 18mm wide x 20m long Thickness 0.18mm Colour Black Material PVC Maximum voltage 600V Flame retardant No Moisture sealing Yes Approvals UL listed, RoHS approved Use Indoor and outdoor SafetyAlways isolate the power before working on wiring and keep the tape away from heat sources and open flame. Keep out of reach of children and store the rolls in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

DETA Insulation PVC Tape in red is a 600V-rated electrical insulation tape in an 18mm x 20m roll, suited to domestic and industrial wiring work. It is a general-purpose PVC tape for insulating and protecting connections, and the red colour also makes it handy for identifying and colour-coding conductors and cables.About the tapeA soft, flexible PVC film with a pressure-sensitive adhesive backing, made to grip well and keep its hold in changing weather. It is 0.18mm thick, resists cold and UV, and seals out moisture. It is lead free, RoHS approved and UL listed. This is the standard (non flame retardant) version, so choose a flame retardant tape if your job calls for one.Where to use itIndoors: insulating and tidying wire joins, terminations and cable runs in domestic and commercial electrical work, and colour-coding wiring.Outdoors: protecting taped connections that are exposed to sun, cold and damp, thanks to its UV and cold resistance and moisture sealing.Suitable for wrapping around insulated and bare conductors, cable joins and wiring harnesses, and for general electrical insulation tasks within its 600V rating.How to use itIsolate the circuit before starting. Make sure the cable or joint is clean, dry and free of oil and dust. Start the tape on a sound area, then wrap it around the joint with a slight stretch and an overlap on each turn so there are no gaps. Carry on past the end of the join onto the cable insulation, then finish with a firm press down of the tail so it sits flat. Cut the tape rather than tearing it so the end does not stretch and lift.Important notesElectrical work should be carried out by a licensed electrician. The tape is rated for use up to 600V and should not be used above that. It is not flame retardant. Keep the tape clear of sharp edges and cable ties that may cut into it. Check the finished wrap and re-wrap if the tape has lifted or been stretched too thin.Specifications Brand DETA Product Insulation PVC Tape Size 18mm wide x 20m long Thickness 0.18mm Pack Single roll Colour Red Material PVC Maximum voltage 600V Flame retardant No Moisture sealing Yes Approvals UL listed, RoHS approved Use Indoor and outdoor SafetyAlways isolate the power before working on any electrical connection, and use the tape within its voltage rating. Keep out of reach of children and store the roll in a cool, dry place away from direct sun and heat. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

DETA Insulation PVC Tape in yellow is a general-purpose electrical tape for insulating, colour-coding and protecting wiring, supplied as a single 20m roll that is 18mm wide. It suits both household and industrial wiring jobs and is rated for use indoors and outdoors.About the tapeA flexible PVC tape with a self-adhesive backing that grips well and gives dependable electrical insulation up to 600V. The film is 0.18mm thick, resists UV and cold, and seals out moisture, so it holds up when exposed to the weather. It is UL listed, RoHS approved and made lead free. This is the standard version, so it is not flame retardant.Where to use itIndoors: insulating and bundling wire joins, colour-coding cables and phases, and covering minor abrasions on wire insulation.Outdoors: protecting cable connections and joins that are exposed to sunlight, cooler temperatures and damp conditions.Suitable for wrapping around wire and cable insulation, terminals and connectors. Yellow makes it handy for marking and identifying circuits or cables.How to use itMake sure the power is isolated first. Wipe the cable or connection so it is clean and dry. Start wrapping slightly past the joint and keep an even tension as you go. Overlap each turn by about half the tape width, then finish a little past the end of the joint and press the tail down firmly. Check that the wrap is snug with no gaps or lifted edges.Important notesThis tape is a standard (non-flame-retardant) grade, so choose a flame-retardant tape if your job calls for one. Electrical work should be carried out by a licensed person where the law requires it. The tape is intended for insulation up to 600V.Specifications Brand DETA Product Insulation PVC Tape Model number 69004B Pack 1 roll Length 20m Width 18mm Thickness 0.18mm Colour Yellow Material PVC Maximum voltage 600V Flame retardant No Moisture sealing Yes Approvals UL listed, RoHS approved Use Indoor and outdoor SafetyUse with normal care and always isolate power before working on wiring. Keep the tape out of reach of children and store it in a cool, dry place away from direct heat and sunlight. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

The DETA White Insulation PVC Tape is a general-purpose electrical tape for insulating, wrapping and colour-marking wiring, supplied here as a single 18mm x 20m roll. It suits both household and industrial jobs, and its UV and cold resistance means it can be used inside or out.About the tapeA soft, flexible PVC film with a self-adhesive backing, 0.18mm thick. It is rated for electrical insulation up to 600V and is UL listed and RoHS approved, so it is lead free. It seals out moisture and is designed to hold its grip and weather well over time. This is the standard (non flame retardant) version, and white is handy for phase marking and tidy colour coding.Where to use itIndoors: insulating and bundling wires, protecting splices and terminations, and colour-coding cables in switchboards, appliances and general wiring.Outdoors: wrapping and protecting connections exposed to sun, damp and cooler conditions, such as garden lighting, sheds and outbuildings.It works well on PVC-insulated conductors and cables, and it is also handy for general harnessing and identification tasks.How to use itIsolate the power first. Clean and dry the surface so it is free of dust, oil and moisture. Start the tape slightly past the area you want to cover, then wrap it in overlapping turns with light, even tension so it conforms to the shape. Finish a little beyond the end of the joint and press the tail down firmly. Use more layers where extra protection is needed. Electrical work should be carried out by a licensed electrician where the law requires it.Important notesThis is a standard PVC insulation tape and is not flame retardant. It is not a substitute for a rated connector or enclosure where one is required. Store rolls in a cool, dry place out of direct sun so the adhesive stays in good condition.Specifications Brand DETA Product Insulation PVC Tape Pack 1 roll Colour White Material PVC Width 18mm Length 20m Thickness 0.18mm Maximum voltage 600V Temperature rating Up to 80°C Flame retardant No Moisture sealing Yes Approvals UL listed, RoHS approved Use Indoor and outdoor SafetyAlways switch off and isolate the power before working on any wiring, and make sure the work is suitable for the circuit you are dealing with. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

DETA Blue Insulation PVC Tape is a general-purpose electrical insulating tape in an 18mm x 20m roll, suited to household and industrial wiring jobs. It grips well, wraps neatly and holds up indoors or outdoors, and the blue colour is handy for identifying or colour-coding cables and connections.About the tapeA flexible PVC film tape with a pressure-sensitive adhesive. It is rated for electrical insulation up to 600V and is listed to UL and RoHS approved. It is also lead free. The film is 0.18mm thick, and it resists cold and UV exposure and seals out moisture, so it keeps performing when exposed to the weather. This is a standard insulation tape, not a flame retardant one.Where to use itIndoors: insulating and bundling wire joins, taping cable ends, colour-coding circuits and general repairs to wiring and leads.Outdoors: protecting and insulating connections and cable runs exposed to sun, cold and moisture.Suited to wiring, cables and connections in domestic, workshop and industrial settings. Always follow the electrical rules that apply to your job, and have licensed electricians carry out any work that the law requires them to do.How to use itMake sure the wire or connection is clean and dry, and isolate the power before you start. Start the wrap a little past the join. Stretch the tape gently as you wind it and overlap each turn so the whole area is covered. Press the end down firmly so it does not lift. Cut the tape rather than tearing it so the edge stays neat.Important notesThis tape is not flame retardant. It is rated to 600V maximum, so do not use it on higher-voltage applications. Check that the tape suits the conditions and the job before relying on it for a critical or permanent repair.Specifications Brand DETA Product Insulation PVC Tape (Model 69001B) Pack Single roll Size 18mm wide x 20m long Thickness 0.18mm Colour Blue Material PVC Maximum voltage 600V Standards UL listed, RoHS approved Flame retardant No Moisture sealing Yes Use Indoor and outdoor SafetySwitch off and isolate power before taping any wiring, and only work on circuits you are qualified and permitted to handle. Keep out of reach of children and store the roll in a cool, dry place away from direct heat. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

DETA Electrical Insulation PVC Tape in yellow / green is a general-purpose 600V rated vinyl insulating tape for wrapping, insulating and colour-marking electrical connections, supplied as a single 20m roll. It suits both household and industrial wiring jobs and is made to hold up in indoor and outdoor settings.About the formulaA flexible PVC film tape with a conformable adhesive layer that grips well and wraps neatly around cables and joints. DETA lists it as UL listed, RoHS approved and lead free, with good resistance to cold and UV exposure and reliable weatherability. The tape is not flame retardant, so choose a flame retardant grade if your job calls for one.Where to use itIndoors: insulating and tidying wire joins, bundling and protecting cables, and colour-coding conductors in switchboards, appliances and general wiring work.Outdoors: protecting and marking connections exposed to the weather, thanks to its moisture sealing and UV and cold resistance. The yellow / green colouring is a handy match for earth conductor identification.Suitable for wrapping over cable insulation, wire joins and conductors in low-voltage and 600V rated applications.How to use itMake sure the cable or joint is clean, dry and free of oil, grease and dust. Start wrapping slightly beyond the area you want to cover, stretch the tape lightly as you go and overlap each turn so there are no gaps. Finish by pressing the end down firmly so it sits flat. Electrical work should always be carried out by a licensed electrician where required by law.Important notesRated for electrical insulation up to 600V. Not flame retardant. Not intended as a replacement for proper connectors, heat shrink or other approved insulation where those are required by the installation. Always switch off and isolate power before working on any wiring.Specifications Brand DETA Product Insulation PVC Tape Pack 1 roll Size 18mm wide x 20m long Thickness 0.18mm Colour Yellow / green Material PVC Maximum voltage 600V Flame retardant No Moisture sealing Yes Approvals UL listed, RoHS approved, lead free Use Indoor and outdoor SafetyAlways isolate and switch off power before wrapping any electrical connection, and use the tape only within its rated voltage. Keep out of reach of children and store the roll in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

DETA Green Insulation PVC Tape is a general-purpose electrical tape for insulating, protecting and colour-coding wiring, supplied as a single 18mm x 20m roll. It suits household and industrial jobs, and its green colour makes it handy for marking or identifying conductors.About the tapeA flexible PVC tape with an adhesive layer that grips well and wraps neatly around joins and cable runs. It is 0.18mm thick, is rated for electrical insulation up to 600V, and is listed to UL and RoHS compliant. The manufacturer describes it as lead free, with good resistance to cold and UV exposure and reliable weatherability. It also seals out moisture.Where to use itIndoors: insulating and bundling wiring, covering splices and terminations, and colour-coding cables in switchboards, workshops and around the home.Outdoors: wrapping connections and cable runs that are exposed to sun, cold and the weather, where the tape's UV and cold resistance help it stay in place.Suitable for wrapping over cable sheathing, wire insulation and common connectors. It is designed as a wrapping tape for wiring, not as a structural adhesive.How to use itMake sure the power is isolated first, then clean and dry the surface so it is free of dust, oil and moisture. Start the wrap slightly past the area you want to cover, then wind the tape with a light stretch and a generous overlap on each turn. Finish a little beyond the other end, press the tail down firmly and cut the tape with scissors rather than tearing it.Important notesThis green tape is not flame retardant. If you need a flame retardant tape, choose a product that is specifically marked as flame retardant. Wiring work must be done to local rules and, where required, by a licensed electrician. For permanent or high-demand joins, always follow the relevant wiring standards.Specifications Brand DETA Product Insulation PVC Tape Size 18mm wide x 20m long Thickness 0.18mm Pack Single roll Colour Green Material PVC Maximum voltage 600V Approvals UL listed, RoHS compliant Flame retardant No Moisture sealing Yes Use Interior and exterior SafetyIsolate the power and confirm circuits are dead before wrapping any electrical connection. Use sharp scissors or a blade with care when cutting the tape. Keep out of reach of children and store the roll in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Boston Premium PTFE Plumbers Pink Thread Seal Tape is a trade-focused thread sealing tape for water pipe fittings, supplied here as a bulk pack of 10 rolls for plumbers who get through plenty of tape. Each roll is 12mm wide and 10m long, and the pink colouring makes it easy to tell apart from other tapes on the truck or in the toolbox.About the formulaThis is a PTFE (polytetrafluoroethylene) film tape that fills the gap in tapered pipe threads to help prevent leaks at threaded joints. It was developed in Australia for professional plumbers, and it is WaterMark approved to WMTS 014:2016 (licence WMK26374). The tape has a density of 0.8g/cm³ and handles a wide temperature range, from -190°C to +310°C, so it suits both hot and cold water lines.Where to use itIndoors: threaded fittings on domestic and commercial water lines, such as taps, valves, unions and connectors.Outdoors: threaded water connections on garden and irrigation lines and other exposed pipework.Suitable for the threaded joints of water pipe fittings. Pink tape is intended for water use, so choose a tape that is rated for gas on any gas fitting.How to use itMake sure the male thread is clean and dry, and free of old tape, oil and debris. Hold the end of the tape on the thread and wrap it around the thread in the direction the fitting will tighten, so the tape does not unwind when the joint is made up. Overlap each turn slightly, keep the tape pulled snug so it presses into the thread grooves, and leave the first thread clear. Tear off the tape, press the end down, then assemble the joint and tighten as normal.Important notesDo not over-tighten, as this can damage fittings. If a joint leaks after assembly, undo it, remove the old tape and rewrap with fresh tape rather than adding more on top. Follow your local plumbing regulations and the fitting manufacturer's instructions for the job.Specifications Brand Boston Product Premium PTFE Plumbers Pink Thread Seal Tape Pack 10 rolls, each 12mm x 10m Colour Pink Material PTFE Density 0.8g/cm³ Temperature range -190°C to +310°C Application Hand wrapped onto threads Standards WaterMark approved, WMTS 014:2016, WMK26374 Use Hot and cold water pipe threads SafetyUse with normal care and keep the work area tidy so loose tape offcuts do not end up in pipework. Keep out of reach of children and store the rolls in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Ametalin Reinforced Insulation / Ducting Tape is a scrim-reinforced foil tape made for joining and sealing reflective insulation and closing up ductwork, supplied here as a single 48mm x 50m roll. It is built to be tougher and more flexible than a standard foil tape, and the manufacturer says it grips with more adhesion and tack than traditional cloth duct tapes.About the formulaThe tape is a 0.178 mm construction made up of aluminium foil, a polyethylene (PE) scrim for reinforcement, and a cold-weather acrylic pressure-sensitive adhesive, supplied on a silicone-coated paper liner. It is vapour sealing and designed to complement Ametalin's reflective membranes. It is UV resistant, fire tested, hand tearable and stands up to humid conditions. The manufacturer rates it for use from minus 30°C to plus 120°C, and says it will not delaminate with age.Where to use itIndoors: sealing joins in foil insulation and wall wraps, taping floor insulation, and closing up HVAC and air-conditioning ductwork.Outdoors and in roof spaces: joining tile and metal roof sarking and sealing laps in wall wraps.Designed for use with reflective foil and foam insulation, roof sarking, wall wraps, floor insulation and ducting. Always test the tape on your own materials before committing to a whole job.How to use itMake sure the surfaces are clean, dry and free of oil and other contaminants. Centre the tape over the join, then press it down firmly with a plastic squeegee so it follows every contour and makes full contact. The tape tears by hand, so you do not need scissors or a knife.Important notesThe manufacturer recommends testing for suitability in your particular application. Store the roll in a clean, dry place out of direct sunlight. For thicker foam-core insulation products, the reinforced tape is the one Ametalin recommends over its standard foil tape.Specifications Brand Ametalin Product Reinforced Insulation / Ducting Tape Pack 1 roll, 48mm wide x 50m long Colour Silver (foil face) Construction Aluminium foil, PE scrim, acrylic pressure-sensitive adhesive, silicone-coated paper liner Total thickness 0.178 mm Adhesive Cold-weather acrylic Temperature range Minus 30°C to plus 120°C Application Hand applied, hand tearable Origin Manufactured in Australia with globally sourced materials SafetyUse with normal care. Wear gloves if you are handling the foil edges or working in a tight roof space, and make sure the area is well lit and ventilated. Keep out of reach of children and store the roll in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

FrogTape Pro Grade Deck and Joist Flashing Tape is a linerless, black waterproofing tape made to shield the timber parts of a deck from moisture, supplied here as a 96mm wide x 15.2m roll. It suits deck joists, stair stringers, posts and ledger boards, adding a protective layer over the surfaces most exposed to water, and it is a practical choice for both builders and capable DIYers.About the formulaThe tape pairs a solventless acrylic adhesive (ShurGRIP) with a conformable black polyolefin film backing. The adhesive is made using a UV curing process, is free of volatile organic compounds (VOCs) and is designed not to react with common caulks and sealants. The film bends easily around edges, corners and other transitions, and the tape self-heals around nails, screws and other fasteners to keep a waterproof seal. It is self-wound, so there is no release liner to peel and dispose of, and no primer is needed.Where to use itOutdoors: the tops and sides of deck joists, stair stringers, posts and ledger boards in residential deck construction, where the tape helps keep water away from framing timber.Installation temperature: it can be applied in a wide range, from -18°C to 65°C, and once installed it is designed to keep performing from -40°C to 115°C. It is rated for all-weather performance, including cold and damp conditions, and has 12-month UV resistance while exposed.Suitable surfaces include pressure-treated timber, OSB, concrete and other common building materials. The adhesive is initially repositionable, so you can adjust placement before pressing it down firmly.How to use itMake sure the surface is clean, dry and free of grease, oil and other contaminants. Unroll the tape along the joist, stringer, post or ledger, position it, then press it down firmly so the adhesive makes full contact. Work the tape around edges and corners, and press it into the surface around fasteners. Wider widths wrap further down the sides of a joist, so choose the width that best matches your framing. The same tape is also made in 48mm, 152mm and 304mm widths.Important notesThe manufacturer states the tape meets the AAMA 711-22 flashing tape test protocol. The 12-month UV resistance applies to the tape while it is exposed, so cover it with your decking or cladding in good time. As with any building product, check that it suits your surface and method of application before starting a larger job.Specifications Brand FrogTape Product Pro Grade Deck and Joist Flashing Tape (FSW 058) Size 96mm x 15.2m roll (1 roll) Colour Black Thickness 0.33mm Backing Black polyolefin film Adhesive Solventless acrylic Liner None (self-wound) Application temperature -18°C to 65°C Service temperature after install -40°C to 115°C UV resistance 12 months Standard AAMA 711-22 Use Exterior, above ground deck framing SafetyUse with normal care and keep the roll away from heat and open flame. Wear gloves when handling the tape on site to protect your hands from sharp edges and fasteners. Keep out of reach of children and store the roll in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Sika Sikasil Auto is a neutral-cure, one-component silicone adhesive sealant made for vehicle repair and trim work, supplied here in a handy 75g tube. It forms a permanent, flexible bond or seal on a wide range of automotive materials, and the cured rubber copes with sunlight, salt spray, temperature swings, vibration and regular car-wash products without hardening, shrinking or cracking.About the formulaA moisture-curing, one-component silicone with a neutral cure, so it does not give off the acidic smell of acetic silicones and is described by the manufacturer as non-corrosive. It cures by reacting with moisture in the air, starting at the surface and working into the core of the joint. Cure speed depends on humidity and temperature, and it cures more slowly in cold conditions. Once cured it is a soft, stretchy rubber with strong thermal, UV, weathering and vibration resistance, and it stays serviceable from -50°C up to 250°C.Where to use itIndoors: bonding small interior components and trim, sealing joints, and cutting down noise and vibration inside the vehicle.Outdoors: sealing and bonding small exterior parts and joints on cars and other vehicles where weather, UV and salt spray are a concern.Suitable materials include fibreglass, metals, most plastics, glass and painted surfaces. Always test on the actual substrates and under your real conditions first to confirm adhesion and material compatibility.How to use itApply at ambient temperatures between 5°C and 45°C onto clean, dry surfaces that are free of oil, grease and dust. Run the sealant into the joint or onto the part and assemble or tool it before it skins over. At 23°C and 50% relative humidity it skins in about 10 minutes and is tack free in about 20 minutes. Excess uncured sealant can be wiped off with Sika Remover-208 or a similar product. Cured sealant has to be trimmed or scraped away mechanically. If you get it on your skin, wash straight away with SikaCleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin.Important notesSikasil Auto cannot be overpainted, so complete any painting before sealing or mask the area. It cures to a depth of about 3 mm in 24 hours, so deeper joints and thicker beads take longer. Check the manufacturer's data sheet for any surfaces or applications where the product is not recommended. This product is designed for vehicle applications. Test first on a small area before committing to the full job.Specifications Brand Sika Product Sikasil Auto Multipurpose Automotive Adhesive Sealant Pack 75g tube Colour Translucent Chemical base 1-component silicone, neutral cure, moisture-curing Application Tube, applied by hand Application temperature 5 to 45°C ambient Skin time About 10 minutes (23°C, 50% r.h.) Tack free time About 20 minutes (23°C, 50% r.h.) Cure speed About 24 hours to a 3 mm depth Density (uncured) 1.0 kg/L Shore A hardness 30 Tensile strength 1.0 N/mm² Elongation at break 600% Service temperature -50 to 250°C Shelf life 18 months when stored below 25°C Use Vehicle interior and exterior SafetyFollow normal good practice for silicone sealants: work in a well-ventilated area, wear gloves and eye protection, and keep out of reach of children. Wash skin promptly after contact using an industrial hand cleaner and water, and do not use solvents on skin. Store in the original sealed tube below 25°C. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

The Deks Dektite Premium #7 is a red silicone roof flashing for sealing larger pipe, flue and vent penetrations through metal roofing, supplied here as a single unit that suits pipes from 150mm to 300mm. A flexible silicone cone fits snugly around the pipe, and a formable aluminium edge lets the large square base follow the shape of your roof sheeting. It is built for the heat, UV and weather swings of Australian roofs.About the productThe cone is moulded from red silicone polymer. Deks rates it for constant temperatures at the roofline from -50°C up to 200°C, so it also suits hot flues and exhausts as well as cold pipes. The cone is designed to hold firm contact against the pipe wall for a watertight seal. The malleable aluminium edge bends to match corrugated and ribbed profiles. The wide 456mm square base gives you a more forgiving fit over a larger or slightly untidy opening. Deks lists UV testing, BAL 29 and other certifications for the range on its product page.Where to use itIndoors: not applicable, this is a roof-top flashing. It is fitted from the outside where the pipe leaves the building.Outdoors: single pipe, flue, vent, exhaust or similar round penetrations on metal roofs, including hot-flue applications that suit the temperature range above.Suitable for a single round penetration with an outside diameter of 150mm to 300mm on metal roof profiles. Check the pipe size before you order, as the cone is trimmed to fit and cannot be made larger.How to use itMeasure the outside diameter of the pipe and trim the silicone cone with sharp shears at the matching point so it grips the pipe snugly. Slide the flashing down over the pipe and bend the aluminium edge to match the roof profile. Fix the base to the roof with suitable screws and seal as recommended by the manufacturer. Check that the cone sits tight against the pipe and that the base follows the sheeting with no gaps.Important notesAlways follow the Deks installation instructions for your roof profile and pipe. Wear gloves when handling the aluminium edge, as trimmed and formed edges can be sharp. This product is a flashing, not a sealant, and the base should be fixed and sealed with fasteners and sealants suited to your roof. If you are unsure about fitting to hot flues or in bushfire-prone areas, check the relevant requirements or ask a licensed roofer or plumber.Specifications Brand Deks Product Dektite Premium #7 Red Silicone Roof Flashing Pack 1 flashing Pipe outside diameter 150mm to 300mm Base size 456mm x 456mm (square) Overall height About 99mm Colour Red Material Silicone cone with formable aluminium base Temperature range at roofline -50°C to 200°C (constant) Roof pitch 0 to 45 degrees Use Exterior, metal roofs SafetyTake normal care when working at heights and use fall protection where required. Wear gloves and eye protection when cutting the silicone cone or bending the aluminium edge. Keep offcuts away from children and pets. Refer to the manufacturer for any safety information supplied with the product. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Boston Silicone Self-Fusing Tape in black is a 3 metre roll of stretchy repair tape made for quick fixes on leaking pipes and hoses. It fuses to itself as you wrap it, so there is no glue involved. It forms a watertight and airtight wrap, which makes it a handy emergency item for the plumbing kit, the toolbox or the shed.About the formulaThis is a silicone tape with no adhesive coating. It bonds only to itself, which means it does not leave sticky residue and can be removed cleanly when the job is done. The tape stretches well beyond three times its length, and that stretch is what lets it pull tight around pipes, hoses and fittings. It is rated for a very wide temperature range, from -55°C to +260°C. The black colour hides dirt and grime and blends in with black fittings.Where to use itIndoors: temporary sealing of weeping pipes, hose joins and fittings around the laundry, bathroom, kitchen or workshop; adding a comfortable, slip-resistant grip to tool handles.Outdoors: emergency repairs on garden hoses and tubing, and general fast fixes around the home, garden or workshop.The tape is designed for wrapping around pipes, hoses, fittings and tool handles. It is a multipurpose repair tape, so it also suits many other small wrap-and-seal jobs.How to use itMake sure the area you are repairing is clean and free of dirt and grease. Peel back the end of the tape and begin wrapping straight over the leak. Stretch the tape as you wind it on and overlap each turn, extending past the damaged spot on both sides. Press the finished wrap firmly so the layers fuse into one continuous seal. To fit a tool grip, wrap the tape around the handle in the same way. Cut the tape to length with scissors or a knife.Important notesBoston positions this tape for emergency and quick repairs. If a pipe or hose is badly damaged, plan to replace the affected section. Because the tape fuses only to itself, it will not stick to a surface if simply laid flat, so always wrap it back over itself. Keep the unused roll in a cool, dry place out of direct sun. Please follow the instructions that come with the pack.Specifications Brand Boston Product Silicone Self-Fusing Tape Pack 1 roll, 3m length Colour Black Material Silicone Application Hand wrapped, fuses to itself (no adhesive) Stretch Over 300% Temperature range -55°C to +260°C Use Pipe and hose leak repair, tool grips SafetyAs a general precaution, keep the tape out of reach of small children. Do not rely on it as a permanent fix for pressurised or safety-critical plumbing. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Kinetic Heavy Duty Thread Seal Tape is a pink PTFE plumber's tape for sealing threaded pipe and fitting connections, supplied here as a handy pack of five 12mm x 10m rolls. It gives a clean, positive seal on screwed joints and helps stop leaks at plumbing and heating connections, with a wide working temperature range for hot and cold duty.About the formulaThis is a PTFE (polytetrafluoroethylene) film tape in a heavy duty grade, coloured pink for easy identification on the job. PTFE is naturally corrosion resistant, so the tape will not rust or degrade the way some paste-type sealants can. It is rated for a working temperature of -100°C to 250°C. The tape is not an adhesive: it works by filling the small gaps between mating threads as the joint is tightened.Where to use itPlumbing: threaded water pipe connections and screwed brass fittings, which is the primary application listed for this pack.Heating: threaded joints in heating pipework and similar screwed connections.Suitable pipe and fitting materials include plastic, brass, copper, aluminium, galvanised steel and iron.How to use itMake sure the threads are clean and free of oil, dust and old sealant. Wrap the tape onto the male thread in the same direction the thread turns, so the tape does not unwind when the fitting is tightened. Keep light tension on the tape so it moulds into the thread form. Use several overlapping wraps (typically about four for small threads, with more for larger sizes), then screw the fitting together and tighten as normal. Test the joint under pressure before putting the system into service.Important notesWrapping against the direction of the thread can cause the tape to bunch up and unwind. Do not over-wrap, as too much tape can make fittings hard to assemble or crack plastic female fittings. Check that the tape is approved for your specific application, such as potable water or gas, before use, as approval details for this exact pack are not confirmed here. Keep away from open flames and do not use beyond the stated temperature range.Specifications Brand Kinetic Product Heavy Duty Thread Seal Tape Pack 5 rolls Roll size 12mm wide x 10m long Thickness 0.1mm Colour Pink Material PTFE Working temperature -100°C to 250°C Corrosion resistant Yes Application Hand wrapped onto male threads Packaging Blister pack SafetyAs general precautions, keep out of reach of children, keep away from open flames, store in a cool, dry place and wash hands after handling. Always follow the manufacturer's instructions and local plumbing regulations. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Rust-Oleum LeakSeal Self-Fusing Silicone Tape is a no-adhesive repair tape for stopping leaks on pipes and hoses and for wrapping damaged wiring insulation, supplied here as a clear 25.4mm x 3.04m roll. It stretches and wraps around awkward shapes, then fuses to itself to form a tight, water-resistant seal that suits quick home fixes as well as automotive and workshop repairs.About the formulaThis is a silicone rubber tape that bonds to itself rather than to the surface underneath. That is why it peels away cleanly later without leaving a sticky residue. The manufacturer rates it excellent for moisture resistance, electrical insulation, UV and ozone resistance and corrosion prevention, and good for flame, abrasion, tear and solvent resistance. It is also rated good to fair for acid and oil resistance. It meets UL 510 and is claimed to insulate up to 8,000 volts.Where to use itIndoors: weeping or leaking pipes and joints, hoses on appliances, and frayed or worn cable insulation (see the electrical safety note below).Outdoors: garden and irrigation hoses, exposed pipework, and vehicle or equipment hoses and fittings exposed to sun and weather.Suited to wrapping around pipes, hoses, fittings and cables made from common materials such as metal and rubber. As the tape fuses to itself rather than relying on adhesion, it conforms to irregular shapes well. Test a small area first on delicate surfaces.How to use itDry the area to be repaired first. Hold the end of the tape firmly on the problem spot, then stretch the tape under tension as you wrap it around the object. Overlap each layer by about 13mm and keep wrapping so the tape lies over itself and fuses. Cover the whole problem area, cut the tape when finished and press the end down firmly. To remove it, simply unwrap or cut it off.Important notesThe tape needs to be stretched while wrapping, with each turn overlapping the last, to fuse properly. Loose or single-layer wraps will not seal. Treat it as an effective repair or emergency fix, and replace damaged pipes, hoses or cables where a permanent solution is needed. The manufacturer lists continuous operating temperatures from -45°C to 200°C and intermittent exposure from -65°C to 260°C, so keep it away from conditions above these limits. Do not rely on it to repair mains-voltage wiring: isolate the power first and have electrical work carried out by a licensed electrician. Avoid contact with strong oxidising agents, strong acids and strong alkalis.Specifications Brand Rust-Oleum Product LeakSeal Self-Fusing Silicone Tape Size 25.4mm x 3.04m roll (1 roll) Colour Clear Material Self-fusing silicone rubber tape Application Hand wrapped under tension, no adhesive or tools Continuous operating temperature -45°C to 200°C Intermittent operating temperature -65°C to 260°C Tensile strength 700 psi minimum Elongation 300% minimum Hardness Shore A 55 (+/- 5) after 24 hours Electrical insulation Up to 8,000 volts (manufacturer claim) Standard Meets UL 510 Use Interior and exterior SafetyWash your hands thoroughly with soap and water before eating, drinking or smoking after handling. If it gets in the eyes, rinse with water and remove contact lenses if present and easy to do. If heated to decomposition, silicone can give off acrid smoke and irritating fumes, so avoid excess heat and ensure good ventilation. Store the roll in a cool, dry place away from strong oxidisers, acids and alkalis. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Rust-Oleum LeakSeal Self-Fusing Silicone Tape is a stretch-and-wrap repair tape for stopping leaks on pipes and hoses and for insulating damaged electrical wires, supplied here as a single black 25.4mm x 3.04m roll. It has no adhesive layer. Instead, each wrap fuses to the layer beneath it, so it forms a tight, sealed sleeve around the repair and can be cut off later without leaving sticky residue behind.About the formulaThis is a silicone rubber tape that bonds to itself rather than to the surface underneath. Rust-Oleum describes it as a moisture and chemical resistant barrier that also helps protect against corrosion. Its technical data sheet rates it Excellent for moisture resistance, electrical insulation, UV and ozone resistance and corrosion prevention. It rates solvent, abrasion and tear resistance as Good. Acid, oil and hydrocarbon resistance is rated Good to Fair. The tape has a minimum tensile strength of 700 psi, a minimum elongation of 300% and a Shore A hardness of 55 (plus or minus 5) once cured for 24 hours. It meets UL 510. Rust-Oleum states it insulates up to 8,000 volts.Where to use itIndoors: temporary or emergency repairs on leaking pipes, fittings and hoses, and insulating or protecting frayed electrical wires and cable joins.Outdoors: wrapping hoses, fittings and exposed connections that face moisture and sunlight, including automotive and general workshop repairs.Because it fuses to itself, it works best on pipes, hoses, cables and other tubular or irregular shapes that you can wrap fully around.How to use itDry the surface before you start. Press the end of the tape onto the problem area, hold it firmly, then stretch the tape with tension as you wrap it around the object. Overlap each layer by about 13mm (the manufacturer gives 1.2 to 1.4cm) and wrap the tape over itself so it fuses. Cover the whole problem area, cut the tape and press the end firmly into place. To remove, cut the tape carefully with scissors or a knife.Important notesThe tape fuses to itself, so wrap it all the way around the item with each layer overlapping the last. The 700 psi figure on the TDS is a tensile strength rating, so do not treat it as a working pressure rating for pipes. Keep pressurised, hot or critical repairs in line with the system's own requirements and replace them with a proper repair where needed. The TDS gives a continuous operating range of -45°C to 200°C and an intermittent range of -65°C to 260°C. Flame resistance is rated Good, so do not treat the tape as fireproof. For electrical repairs, make sure the circuit is isolated and have any permanent work done by a licensed electrician.Specifications Brand Rust-Oleum Product LeakSeal Self-Fusing Silicone Tape Model number 279241 Size 25.4mm wide x 3.04m long roll (single roll) Colour Black Base Self-fusing silicone rubber Application Hand applied, stretch and wrap Continuous operating temperature -45°C to 200°C Intermittent operating temperature -65°C to 260°C Tensile strength 700 psi minimum Elongation 300% minimum Hardness Shore A 55 (plus or minus 5), cured 24 hours Electrical insulation Up to 8,000 volts (manufacturer rating) Standard Meets UL 510 Use Interior and exterior SafetyIf it gets in your eyes, flush with plenty of water for at least 15 minutes, keep the eyelids open, remove contact lenses if easy to do and keep rinsing. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Selleys Auto Fix Windscreen Sealant 100 mL - Black Stop leaks fast around windscreens and windows with a durable, weather resistant silicone seal. Selleys Auto Fix Windscreen Sealant forms a waterproof barrier that resists vibration, UV and temperature extremes, keeping water, dust and drafts out. Why choose this sealant 100 percent neutral cure silicone for reliable sealing Forms a waterproof seal to stop leaks quickly UV and weather resistant for long term performance Skins in 5 minutes and is touch dry in about 30 minutes Handles joint movement up to 25 percent Suitable surfaces Glass and windscreens Rubber surrounds and trims Painted surfaces and most plastics Metal frames and channels Typical applications Sealing between windscreen glass and rubber Sealing between rubber and metal frames Stopping minor water ingress around vehicle windows General sealing where a flexible, black silicone finish is desired Key specifications Technology Neutral cure silicone Colour Black Movement capability Up to 25 percent Skin time About 5 minutes Set time About 30 minutes Full cure Approximately 24 hours Service temperature -40°C to 180°C Application temperature -20°C to 50°C VOC 26 g/L Pack size 100 mL tube Directions Remove any dirt or moisture between the rubber and glass, or rubber and metal. Clean with mineral turpentine and allow to dry. Remove cap, unscrew nozzle, pierce inner seal, refit nozzle, then cut the tip at a 45 degree angle. Insert the nozzle between the rubber and glass or rubber and metal where possible. Squeeze the tube with steady pressure to push sealant into the joint. Smooth off with a gloved finger. If additional smoothing is needed, do it before the sealant skins. Clean up uncured sealant with mineral turpentine. Cured material must be cut or scraped away. Replace the cap after use. Allow sealant in the nozzle to cure, then remove before next use. Handy tips For neat lines, mask both sides of the joint and remove tape before the sealant skins. Best results occur when the joint is clean, dry and free of loose material. Limitations Not recommended on natural rubber, NBR or chloroprene neoprene due to poor adhesion. Clean up and storage Clean uncured sealant with mineral turpentine. Remove cured sealant by cutting or scraping. Store in a cool, dry place below 30°C. Use within 24 months of production. What you get 1 x Selleys Auto Fix Windscreen Sealant 100 mL - Black

Read more less

Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®

Read more less

High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. SafetyTips Uncured product may irritate eyes. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Refer to the Safety Data Sheet (SDS) for full details.Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.

Read more less