Holds up to 13.6Kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$11.55
Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistantRecommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$12.95
Features Resists intense heat Sets hard Water clean up Where can this product be used? Repairing bricks in fireplaces and chimneys Sealing flues in pot-belly stoves Filling cracks in ironworks and bricks What materials is this product suitable for? Brick Metal Concrete How to Use: Remove all dust, grease and loose debris before applying material. Dampen the cavities on porous surfaces for better adhesion. Apply Fireproof Cement firmly into holes and cracks with a damp knife or spatula. Allow Fireproof Cement to dry a minimum of 48 hours before exposure to heat. If Fireproof Cement is stiff slacken with a little water. Limitations: Fireproof Cement is not an adhesive - it is a filling compound. Not recommended for external use e.g. BBQ's, incinerators etc. Fireproof Cement is not suitable for use in kilns. Fireproof Cement is not recommended for moving joints such as expansion joints as it sets rigidly Hardened material cannot be resoftened with water.
$49.46
LOCTITE® SI 598™ cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. This product resists aging, weathering and thermal cycling without hardening, shrinking or cracking. Typical applications include oil pans, transmission pans, valve covers, valves and guides, timing gear covers, and differential covers. This product is typically used in applications with an operating range of -54 °C to 260 °C. Metallic black, 1-part, thixotropic, room temperature vulcanizing oxime silicone paste sealant. LOCTITE® SI 598 is a metallic black, 1-part, thixotropic, room temperature vulcanizing oxime silicone paste sealant. It cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. It resists ageing, weathering and thermal cycling without hardening, shrinking or cracking. This product is typically used in applications with an operating range of -54 to +260°C. Excellent resistance to automotive motor oils Enhances load bearing & shock absorbing characteristics of the bond area Typical applications include oil pans, transmission pans, valve covers, valves and guides, timing gear covers, and differential covers Technical Information Color Black Fixture Time 30 Fixture Time Temperature 30 °C Physical Form Paste Technology Silicone TYPICAL ENVIRONMENTAL RESISTANCE The product retains effective properties in contact with automotive fluids, such as motor oil, transmission fluids, alcohol and antifreeze solutions. NOTE: Not recommended for parts in contact with gasoline. Directions for use: 1. For best performance bond surfaces should be clean and free from grease. 2. Full performance properties will develop over 72 hours. 3. Moisture curing begins immediately after the product is exposed to the atmosphere, therefore parts to be assembled should be mated within a few minutes after the product is dispensed. 4. Excess material can be easily wiped away with non-polar solvents. NOTE: LOCTITE® SI 598™ is not recommended for use as a cylinder head gasket or head gasket sealant. 5. For full automatic applications a volumetric dispensing system is recommended.
$15.52
Loctite Pre Mixed Epoxy 60 seconds is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 60 seconds and reaches handling strength in 5 to 10 minutes. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. octite Pre Mixed Epoxy 60 seconds does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on Great for crafting projects Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fiberglass, concrete and stone Can be combined with fiberglass cloth for a durable patch Properties High impact resistance: won’t crack when drilled Can be tinted to match surrounding materials Water resistant and can be used outdoors Does not shrink Convenient instant mix syringe Consistently dispenses equal, uniformly mixed amounts of each component Sets in 40 to 60 seconds Quick completion of project HOW TO USE: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from center of plunger. Turn nozzle end up and pull plunger back slightly allowing air bubbles to rise to top. Snap off and discard end of syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$7.91
Loctite Epoxy Instant Mix 5 Minute is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 5 minutes and reaches handling strength in 1 hour. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. Loctite Epoxy Instant Mix 5 Minute does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on: Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fibreglass, concrete and stone Can be combined with fibreglass cloth for a durable patch Great for crafting projects Properties Will not crack when drilled Can be tinted to match surrounding materials Water resistant: can be used outdoors Does not shrink One-time application Convenient instant mix syringe Consistently dispenses equal, uniformly mixed amounts of each component Sets in 5 minutes Quick completion of the project How to Use: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from the centre of the plunger. Turn nozzle end up and pull the plunger back slightly allowing air bubbles to rise to the top. Snap off and discard end of the syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto the surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$9.23
DUNLOP®WALL TILE ADHESIVE is a ready-mixed indoor wall tile adhesive. Ideal for all types of ceramic wall tiles and dimensional stones such as marble and granite, it can be used on a number of surfaces which include compressed fibre-cement sheets, plasterboard, cement render and adequately prepared painted surfaces (oil-based paint only). DUNLOP®WALL TILE ADHESIVE has superior flexibility and high grab to support even the heaviest of wall tiles. SURFACE PREPARATION Surfaces must be consistently flat and firmly fixed. Clean off dust, oil, grease and all loose contaminating materials or coatings. Ensure surfaces are dry, with no residue or permanent dampness. Prime porous surfaces (e.g. fibre- cement sheets, cement render) with DUNLOP®PRIMER & ADDITIVE beforehand and allow to dry. Cement Render Allow to cure for at least 7 days. Render should have a wood float finish. Plasterboard There is no need to prime the cardboard surface. However, where sheets are joined, DUNLOP®PRIMER & ADDITIVE must be used over the base jointing compound. Do not use the topping compound in areas which are to be tiled. Compressed Fibre-Cement Sheets Remove surface dust with a damp sponge and prime with DUNLOP®PRIMER & ADDITIVE and allow to dry before tiling. Painted Surfaces Oil-based paint should be roughened mechanically and loose flaking paint should be removed. Ensure the paint is suitable for tiling over. Thoroughly remove water-based paints. Do not use paint stripper or solvents. Allow surface to dry after cleaning. MIXING No mixing required. APPLICATION As a general guide use a 6mm notch trowel to spread adhesive achieving a minimum 1mm bed thickness. Do not wet tiles before fixing. If backs of tiles are dusty clean with a damp sponge. Spread the adhesive with the notches running horizontally across the wall. Spread only one square metre at a time and ensure a skin has not developed on the adhesive before bedding tiles. Press and slide the tile into position ensuring the whole of the back of the tile is in good contact with the adhesive. Use tile spacers if desired to ensure even spacing. Remove any surplus adhesive on face of tile or between joints before it sets. Adjustment of tiles should be carried out within 60 minutes of laying (at 23°C and 50% humidity). COVERAGE DUNLOP®WALL TILE ADHESIVE will cover approximately 0.5m2per kg. Coverage will vary depending on the condition of the surface being tiled and application technique. DRYING TIME DUNLOP®WALL TILE ADHESIVE will dry in approximately 24 hours depending on ambient temperature, porosity of surface and tiles. MOVEMENT JOINTS Incorporate movement joints at 3.5m intervals and at internal corners. Any structural movement joints must be carried through to the face of the tiling, at junctions between different background material and at fixtures interrupting the tile surface. These joints should be about 6mm wide and and kept free from adhesive. They should be filled with a high quality flexible material e.g. DUNLOP®COLOURED SILICONE. GROUTING Wait until adhesive has set. This takes approximately 24 hours. Remove tile spacers and use DUNLOP®GROUT adding DUNLOP®PRIMER AND ADDITIVE to enhance colour, impart a degree of flexibility and reduce porosity and staining. For easier maintenance seal with DUNLOP®GROUT SEALER. CLEAN UP While it is still fresh, DUNLOP®WALL TILE ADHESIVE can be cleaned off with a damp sponge. Tools, hands and material soiled with adhesive can be easily cleaned with water as long as the adhesive is still fresh. CAUTION Do not use DUNLOP®WALL TILE ADHESIVE to fix green marble. Do not use DUNLOP®WALL TILE ADHESIVE in continuous immersion applications e.g. swimming pools, tanks etc.. Do not use DUNLOP®WALL TILE ADHESIVE over non- absorbent substrates and waterproofing membranes due to prolonged drying times. DUNLOP GUARANTEE Product is guaranteed for 10 years when installed to manufacturers instructions. Manufactured under a quality system certified as complying with ISO 9001 by an accredited certification body. Material Safety Data Sheets are available TECHNICAL DATA Characteristics of product: Colour: White Viscosity: 790 000 cps S.G: 1.47g/cm3 pH: 9.1 Form: Viscous paste Application Properties: (@23°C and 50% relative humidity) Open Time: 80 mins Adjustability Time: 60 mins Mechanical Properties: Fundamental Characteristics Shear adhesion strength: Shear adhesion strength after aging: 2.5 Mpa (AS 4992.1) Minimum requirements 1.0Mpa (D1) 3.5 Mpa 1.0Mpa (D1) SAFETY Keep out of the reach of children. If skin contact occurs wash skin thoroughly with running water. If swallowed, give a glass of water and contact Poisons Information Centre. In case of contact with eyes, rinse with plenty of water and contact a Doctor. MSDS available on request.
$66.83
High-Performance Ready-Mixed Ceramic Tile Adhesive This high-grab adhesive is designed to support even the heaviest wall tiles, providing superior flexibility for interior applications, particularly in kitchens and bathrooms. Key Features: Ready-mixed adhesive High grab for heavy wall tiles Superior flexibility Tile Types: Ceramic wall tiles Granite Marble (excluding moisture-sensitive stone) Suitable Surfaces: Cement render Fibre-cement sheets Painted surfaces (properly prepared) Plasterboard Application Areas: Indoor walls Coverage: 0.5m² per kg
$19.86
Davco® Sanitized Glue Grout A Pre-mixed, Ready-to-Use Wall Tile Adhesive and Grout Davco® Sanitized Glue Grout is a flexible, white, pre-mixed adhesive and grout for internal wall tile applications. Ideal for thin bed fixing of porous-backed ceramic tiles, it’s suitable for domestic areas like bathrooms, kitchens, and laundries. Key Features: White appearance Pre-mixed and ready for immediate use Dual-purpose: serves as both adhesive and grout Ideal for fixing lifted or popped tiles No wastage Usage: Surfaces: Cement renders Rendered brickwork and blockwork Plasterboard Fibre-cement wall sheets Tiles: Suitable for thin-bed fixing of most porous-backed ceramic tiles Areas: Interior applications, including domestic walls, bathrooms, kitchens, and laundries Advantages: Ready to use, no mixing required Suitable for adhesive and grout in one product Convenient for quick repairs or installations No product wastage Packaging & Colour: Packaging: 500g pail Colour: White paste Application Information: Adjustability Time: 20-30 minutes (depending on climate and substrate porosity) Ready for Use: 24 hours Note: Drying time may vary based on climate, substrate, and tile porosity. Coverage: A 500ml tub of Davco® Sanitized Glue Grout covers approximately 0.5m² when applied with a 6mm notched trowel as an adhesive. Application Steps: Surface Preparation: Ensure all surfaces are structurally sound, dry, clean, and free of contaminants like oil, grease, or loose material. Deeply contaminated surfaces should be abraded to expose at least 80% of the original substrate. Follow these preparation guidelines: Substrate Specific Requirement Primer Rendered brick/blockwork Cured minimum 7 days, sound Davco PrimeX or Ultraprime Fibre-cement sheet/plasterboard Correctly and firmly fixed Davco PrimeX or Ultraprime Previously painted surfaces Sand back to expose 80% of surface Davco PrimeX or Ultraprime Mixing: No mixing required. Davco® Sanitized Glue Grout is ready to use straight from the pail.
$24.79
Davco Grey One Pot Premixed Tile Adhesive is a high-performance, ready-to-use acrylic-based adhesive, perfect for interior wall and floor tiling. Its premixed formula eliminates the need for onsite preparation, providing excellent adhesion and ease of application for both professionals and DIYers. Surface Preparation: Ensure all surfaces are sound, dry, and free from dust, oil, grease, or any other contaminants. Painted or glossy surfaces should be roughened and cleaned. For porous surfaces, priming may be required to ensure maximum adhesion. Application Instructions: Stir the adhesive thoroughly before use. Using a notched trowel, apply the adhesive to the substrate. Only spread as much adhesive as can be tiled within 20 minutes. Firmly press tiles into the adhesive, ensuring full coverage on the tile back. Adjust tiles within 20 minutes of placing them. Allow adhesive to set for 24 hours before grouting. Coverage: Approximately 0.75–1.25 m² per litre using a 6mm notched trowel. Coverage may vary depending on substrate and trowel size. Drying Time: Allow 24 hours before grouting. Full cure achieved within 7 days under normal conditions. Clean Up: Clean tools and excess adhesive with water immediately after use. Once dried, adhesive is more difficult to remove. Technical Data: Appearance: Grey paste Base: Acrylic Open Time: 20 minutes Adjustment Time: 20 minutes Application Temperature: 5°C to 35°C Ready for Grouting: After 24 hours
$30.24
These non-yellowing dots are easy to use, acid and lignin free, making them ideal for use in the home, office and school as an alternative to drawing pins, staples or tape. They are solvent-free and non-toxic. Bostik Glu Dots are also available in an extra strength version, for permanent applications. Key Features Repositionable Transparent, non-visible Solvent-free and non-toxic Acid and lingin free, suitable for photographs Description Bostik Removable Glu Dots are little circles of double-sided, clear adhesive which stick almost anything including paper, wood, plastic, metal, glass and painted surfaces. These non-yellowing dots are easy to use, acid and lignin free, making them ideal for use in the home, office and school as an alternative to drawing pins, staples or tape. They are solvent free and non-toxic. Bostik Glu Dots are also available in an EXTRA STRENGTH version, for permanent applications. APPLICATIONS - Holding up posters, cards, certificates, notices, maps, menus, calendars, messages, timetables, learning aids, children paintings, decorations, etc. - Keeping in place telephones, mouse pads, pens, candles, figurines, vases, calculators, ornaments, etc. - Keeping picture frames straight. - Sticking photos in an album. - Ideal for school projects, scrapbooking, art and craft projects. ADHESION Bostik Removable Glu Dots sticks extremely well to non-porous surfaces such as metal, glass, plastics, vinyl coated and painted surfaces and porous surfaces such as paper, boards, cloth, and wood. LIMITATIONS - Not suitable for highly absorbent, damp or dusty surfaces. - Not suitable for holding up heavy objects. - May damage delicate papers on removal. Safety Instructions: Bostik Removable Glu Dots is non-toxic. The product poses a choking hazard if ingested. In the event of ingestion, the mouth should be washed with water. Seek medical assistance if irritation or discomfort persists. Refer to our Safety Data Sheet for further toxicological information and comprehensive handling instructions. Surface Preparation: Ensure that surfaces are clean, dry and free of any dust, grease and loose materials. How to Use: 1. Tear along the perforations. 2. Peel off the paper backing. 3. Press the dot firmly onto the first surface. 4. Remove the clear film. 5. Press the second surface firmly onto the dot. 6. Reposition if necessary Cleaning Remove dots carefully by rubbing and rolling them off. Use mineral turpentine to remove any remaining residue. Storage The shelf life of the product is indefinite if stored at room temperature. Packaging 64 Glu Dots in a wallet
$9.95
These non-yellowing dots are easy to use, acid and lignin free, making them ideal for use in the home, office and school as an alternative to drawing pins, staples or tape. They are solvent-free and non-toxic. Bostik Glu Dots are also available in an extra strength version, for permanent applications. Ket Features: -Repositionable -Transparent, non-visible -Solvent-free and non-toxic -Acid and lingin free, suitable for photographs Description Bostik Extra Strength Glu Dots are little circles of double-sided, clear adhesive which exhibit high tack, offering secure bonds to almost anything including paper, wood, plastic, metal, glass and painted surfaces. These non-yellowing dots are designed to provide a permanent hold and the bond strength will increase over time. They are easy to use, acid and lignin free, making them ideal for use in the home, office and school as an alternative to drawing pins, staples or tape. They are solvent free and non-toxic. Bostik Glu Dots are also available in a REMOVABLE version, for non-permanent applications. Applications - Holding up posters, cards, certificates, notices, maps, menus, calendars, messages, timetables, learning aids, children paintings, decorations, etc. - Keeping in place telephones, mouse pads, pens, candles, figurines, vases, calculators, ornaments, etc. - Keeping picture frames straight. - Sticking photos in an album. - Ideal for school projects, scrapbooking, art and craft projects. Adhesion Bostik Extra Strength Glu Dots Stick extremely well to non-porous surfaces such as metal, glass, plastics, vinyl coated and painted surfaces and porous surfaces such as paper, boards, cloth, and wood. Limitations - Not suitable for highly absorbent, damp or dusty surfaces. - Not suitable for holding up heavy objects. - May damage delicate papers on removal. Safety Instructions Bostik Extra Strength Glu Dots is non-toxic. The product poses a choking hazard if ingested. In the event of ingestion, the mouth should be washed with water. Seek medical assistance if irritation or discomfort persists. Refer to our Safety Data Sheet for further toxicological information and comprehensive handling instructions. Surface Preparation Ensure that surfaces are clean, dry and free of any dust, grease and loose materials. How to use 1. Tear along the perforations. 2. Peel off the paper backing. 3. Press the dot firmly onto the first surface. 4. Remove the clear film. 5. Press the second surface firmly onto the dot.
$9.95
Ready-to-use or single-sachet formats for clean, consistent application with minimal setup. Ideal where accurate dosing and quick turnaround are key. Check re-sealability and working time once opened. Use filters to refine by chemistry, cure speed and clean-up. Always review the product page and TDS/SDS.
