🌍 Worldwide Shipping Available | Fast & Secure Delivery ✈️

Works on: Leather

124 products

  • Loctite Super Glue Professional Water Resistant 20g Loctite Super Glue Professional Water Resistant 20g

    Loctite Loctite Super Glue Professional Water Resistant 20g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $23.00

  • Un-Du Adhesive & Sticker Remover Acid-Free Formula Un-Du Adhesive & Sticker Remover Acid-Free Formula

    Timbermate Un-Du Adhesive & Sticker Remover Acid-Free Formula

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Say Goodbye to Stubborn, Sticky Messes! Tired of wrestling with stubborn price tags that tear and leave a papery, sticky mess? Frustrated by gummy residue left behind by tape on new appliances or furniture? We've all been there, risking our fingernails and damaging surfaces trying to scrape and scrub away unwanted adhesives. It’s time to stop the struggle. Introducing Un-Du® Adhesive Remover, the ultimate solution from Glues Australia that works like magic. This isn't just another solvent; it's a revolutionary removal system. Unlike harsh chemicals that dissolve glue and ruin your items, the Un-Du® formula cleverly works by temporarily neutralizing the adhesive. A few drops are all it takes to seep under the label or sticker, breaking the bond with the surface. Simply lift it off cleanly and effortlessly with the handy included scraper tool. The best part? Once the fast-evaporating Un-Du® formula disappears, the stickiness on the sticker returns, allowing you to reuse it somewhere else! It’s the perfect tool for repositioning labels, photos, and more. An Essential Tool for Every Australian Home From the kitchen to the garage, you'll find hundreds of uses for Un-Du®. It’s the one tool that’s more versatile than duct tape, designed to solve all those sticky problems that pop up in daily life. Keep a bottle handy and you'll always be prepared. Gift Giving Made Easy: Effortlessly removes price stickers from delicate gifts like crystal vases, books, and photo frames without leaving a trace. Clean Up Your Car: Finally get rid of that old bumper sticker from your ute or the remnants of a parking permit on your windscreen without damaging the paint or glass. Appliance & Furniture Rescue: Safely removes warranty stickers, energy rating labels, and masking tape from new fridges, TVs, and fine wood furniture. Household Accidents: Lifts chewing gum from carpet, tar from floors, and crayon marks from walls with remarkable ease. The Ultimate Office & Warehouse Productivity Hack Streamline your workflow and maintain a clean, professional workspace. Un-Du® is an indispensable asset for any office, mailroom, or warehouse environment, saving you time, money, and frustration. Package & Mail Management: Open self-sealing envelopes and padded mailers without tearing them, perfect for retrieving contents or reusing packaging. File & Asset Organisation: Easily remove and replace labels on files, shelves, computer disks, and office equipment without leaving a sticky, dirt-collecting residue. Mistake Correction: Quickly lifts correction fluid (White Out) from documents without smudging or tearing the paper. Workspace Maintenance: Removes old tape marks from desks, partitions, and windows, keeping your office looking pristine. A Must-Have for Crafters and Memory Keepers Your precious memories and delicate projects deserve the best care. The Un-Du® formula is completely acid-free and photo-safe, making it the trusted choice for hobbyists, scrapbookers, and archivists who demand perfection and preservation. Scrapbooking Perfection: Safely lift and reposition photos in albums and scrapbooks without causing fading, yellowing, or damage. Model Making: Remove masking tape from delicate models without lifting paint or leaving residue. Paper Crafts: Adjust stickers and embellishments on acid-free and lignin-free papers with total confidence. Stop struggling and start un-sticking the clean, simple, and safe way. Add Un-Du® Adhesive & Sticker Remover to your cart today and discover a world free from sticky situations! Product Specifications Brand: Un-Du® Product Name: Adhesive & Sticker Remover Formula: Acid-Free, Photo-Safe, Quick-Evaporating Solvent Key Feature: Temporarily neutralizes adhesives, allowing for the reuse of most stickers and labels after evaporation. Residue: Leaves no oily, greasy, or sticky residue behind. Tool: Comes with an attached, non-scratching, integrated scraper tool for easy lifting. Common Applications: Sticker & Label Removal Tape & Decal Removal Price Tag Removal Gum & Tar Cleaning Correction Fluid (White Out) Lifting Opening Sealed Envelopes Safe For Use On Surfaces Including: Glass & Plastics Fine Wood Furniture Metals Carpets & Upholstery Delicate Fabrics Photos Acid & Lignin-Free Papers Painted Surfaces & Wallpaper And much more!

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $19.00

  • Araldite 5 Minute Epoxy Adhesive Holds 75Kg For Everyday Use Dries Clear 35ml Araldite 5 Minute Epoxy Adhesive Holds 75Kg For Everyday Use Dries Clear 35ml

    Selleys Araldite 5 Minute Epoxy Adhesive Holds 75Kg For Everyday Use Dries Clear 35ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $18.00

  • Sale -12% Loctite Super Glue Gel Power Flex Rubber Infused Formula Extra Strong and Flexible 3g Loctite Super Glue Gel Power Flex Rubber Infused Formula Extra Strong and Flexible 3g

    Loctite Loctite Super Glue Gel Power Flex Rubber Infused Formula Extra Strong and Flexible 3g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    The unique rubber-infused gel formula allows powerful bonds that are extremely precise even on flexible materials. Ideal for porous and vertical surfaces, and strong enough to withstand extreme conditions. The gel’s high strength non-drip formula then dries transparent to form invisible bonds that give a long lasting durability that is both weather and shock-resistant. For intricate, hard to reach spots, Loctite Power Flex Gel Control features an easy grip squeeze bottle and nozzle for precise applications. Recommended on: Rubber, Leather, Wood, Metal, Porcelain, Paper, Plastic. Properties: -Rubber infused gel formula for extra strong and flexible bonds -Ideal for porous and vertical surfaces -Water resistant -Bonds in seconds -Withstands heavy loads -Dries transparent -Easy to open, self-piercing and anti-clog cap -Choice of applicators: convenient tube or easy grip control with a longer nozzle -Suitable for use on most surfaces* -Solvent-free -* Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Step by Step Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $12.50 $10.95

  • Selleys All Plastics Glue - Strong and fast bond Perfect For Broken Toys (Glue + Primer) 3ml Selleys All Plastics Glue - Strong and fast bond Perfect For Broken Toys (Glue + Primer) 3ml

    Selleys Selleys All Plastics Glue - Strong and fast bond Perfect For Broken Toys (Glue + Primer) 3ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Easy to use, fast setting adhesive system to repair ALL plastics. Features -Bonds ALL Plastics, including Polyethylene (PE) and Polypropylene (PP) -Easy to Apply -Dries clear for clean, neat results -Fast Bond: 2-30 seconds -No clamping necessary -No mixing required -self-piercing, clog-free cap on adhesive -Also bonds plastic to other surfaces: Metal, timber, china, rubber, leather Where can this product be used? -For interior projects and repairs -For fast & easy repair of household items made from plastic -Repair Toys & Games -Fix Car accessories -Repair Kitchen plastics and utensils -Repair Office items -Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet -Best results for Nylon items (e.g. car parts) are achieved without initial priming. Contact Selleys consumer advice if unsure of plastic type. -Not suitable for use on glass – we recommend Selleys Araldite Ultra Clear. What materials is this product suitable for? -ALL Plastics -Adhering Plastic to Metals China Rubber Leather How to use this product -Ensure the surfaces to be joined are close fitting, clean, dry and free of dust. -Using the primer pen, liberally coat plastic surface/s that are to be bonded. -Pierce seal at end of the adhesive tube by attaching nozzle and cap and turning clockwise. -Remove cap and apply a very small amount of glue to one surface only. Bring surfaces together and apply slight pressure. -The adhesive will grab within 2-30 seconds, depending on environmental conditions and materials being bonded. -Allow at least 30 minutes for sufficient bond strength for practical use. -Wipe tip of the tube, replace the cap and store upright in a dry cool place. Handy tips -If using on leather test on an inconspicuous area first as adhesive may cause leather to discolour or harden. -Not suitable to repair items that will contain hot liquids. -Best results for nylon items are achieved without Initial priming (e.g car parts). Contact Selleys Consumer Advice if unsure of plastic type. -Will also bond plastic to non-plastic surfaces (Metals, Timber, China, Rubber, Leather). Do not use primer on non-plastic surfaces. -After use, wipe excess product from the adhesive nozzle with a tissue dipped in nail polish remover. -For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. -In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in the hot soapy water. -Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use. Safety tips -Keep Out of reach of Children -Avoid contact with skin and eyes and avoid breathing in the vapour. -Bonds on contact. Should fingers stick together apply a solvent such as acetone (nail polish remover) to contact areas then wash with water. -Do not use solvents near eyes or open wounds. -Highly Flammable, keep away from sources of ignition. -Contents of the pen may cause lung damage if swallowed. -This product is hazardous according to the criteria of NOHSC and HSNO. For frequent hobby or occupational use, please refer to the Material Safety Data Sheet. -For Advice, contact a Poisons Information Centre (phone Aust. 131 126, NZ 0800 764 766) or a doctor. -In case of eye contact immediately flush with water for at least 15 minutes and seek medical attention. Storage and re-use -Ensure caps are replaced and store in a cool dry place.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $8.51

  • Boyle Clear Craft Glue Quick Drying Ideal For Crafts 500ml Boyle Clear Craft Glue Quick Drying Ideal For Crafts 500ml

    Boyle Boyle Clear Craft Glue Quick Drying Ideal For Crafts 500ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Clear Boyle Craft Glue Boyle Craft Glue (Clear) is a versatile, water-based adhesive designed for everyday making and detailed craft work. It dries clear and odourless, making it perfect for neat, mess-free results on paper projects, school assignments, scrapbooking, model making, décor builds and more. Why You’ll Love It Dries crystal clear for a clean, professional finish. Water-based & odourless for a low-fuss, indoor craft experience. Heat & light resistant—ideal for display pieces exposed to room lighting/sunlit interiors. Easy-squeeze bottle gives smooth, controlled bead lines and spot application. Cleans up with water—simply wipe while wet for quick tidy-ups. Suitable Materials Formulated for strong, reliable bonds on: Paper, cardboard & posters Wood, balsa & craft sticks Plastics* Glass & ceramics Metal embellishments Fabrics & felt Yarns, beads & sequins Leather and more *Always test first—some low-energy plastics may require light surface prep. Great For School projects & classroom crafts Cardmaking, scrapbooks & photo boards DIY décor, event styling & mood boards Miniatures, models & hobby builds Textile embellishment on felt and fabric (non-washwear items) How to Use Prep: Ensure surfaces are clean, dry and free of dust or oils. Lightly roughen very smooth surfaces for best grab. Apply: Squeeze a thin, even layer to one surface. For porous materials (paper, cardboard, wood), a little goes a long way. Assemble: Press parts together. Use light pressure, clips or tape if needed to hold while setting. Dry: Allow to dry thoroughly. Dry time varies with bead thickness, temperature and humidity. Clean-up: Wipe excess immediately with a damp cloth. Wash tools in water while glue is still wet. Good to Know Indoor use: Formulated for indoor crafting and display. Clear finish: Dries transparent to help hide glue lines and squeeze-out. Heat & light resistance: Helps projects maintain appearance under typical indoor conditions. Washes out with water: Clean hands, tools and fresh spills while wet. Specifications Base Water-based Appearance (dry) Clear Odour Odourless Cleanup Water (while wet) Use Indoor Tips & Testing For non-porous surfaces (glass, metal, some plastics), apply a thin coat to each surface, wait briefly, then join for better grab. Always perform a small test on off-cuts or an inconspicuous area to confirm compatibility and finish. Avoid heavy, load-bearing or structural applications—this is a craft-grade adhesive. FAQs Does it dry clear?Yes—Boyle Craft Glue dries clear for a neat finish. Can I wash it out?Yes—while wet, it washes out with water. Once fully dry/cured, removal may be more difficult. Is it suitable outdoors?It’s designed for indoor craft projects. For outdoor or constantly wet environments, choose a weather-rated adhesive.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $14.89

  • Tarzan's Grip General Purpose Glue Clear Flexible Water Resistant 30ml Tarzan's Grip General Purpose Glue Clear Flexible Water Resistant 30ml

    Tarzan's Grip Tarzan's Grip General Purpose Glue Clear Flexible Water Resistant 30ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Tarzan’s Grip new formulation is a clear, flexible, general purpose solvent-based adhesive for household and hobby uses. An all-purpose glue which bonds almost everything Grabs in minutes - the exact "grab time" depends on the surfaces to be joined Fast drying Water resistant

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $4.89

  • Selleys KwikGrip Spray 150g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces

    Selleys Selleys KwikGrip Spray 150g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys KwikGrip Spray 150g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces Adhesive Mastery: Quick, Clear & Heat Resistant Discover the power of Selleys KwikGrip Spray 150g, a versatile adhesive spray that bonds instantly on contact. Ideal for both absorbent and non-absorbent surfaces, it offers a quick-drying and heat-resistant solution for a multitude of projects. Key Features: Versatile adhesive spray Durable bond Fast drying and dries clear Heat resistance up to 70°C Common Applications: Car upholstery repairs Fixing laminate on tables and bench tops Patching vinyl flooring Art and craft projects And many more... Compatible Materials: Laminated plastics Timber Craft foam Aluminium Leather Canvas Rubber Most plastics* How to Use: USE ONLY IN A WELL VENTILATED AREA. Shake the can well. Ensure surfaces are clean and dry. Hold the can 20cm away and spray surfaces evenly. For a permanent bond, spray both surfaces and wait until touch dry before pressing together. Clamp overnight for a firm bond. For a temporary bond, spray one surface and press together while still tacky. Limitations: Not suitable for bonding rough, ill-fitting surfaces or certain plastics like polyethylene or polypropylene. Refer to the guidelines for alternative solutions. Handy Tips: After use, clean the nozzle by inverting the can and spraying until clear

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $11.00

  • QuickFix Control Bottle Supa Glue High Precision Nozzle 3g

    Selleys QuickFix Control Bottle Supa Glue High Precision Nozzle 3g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Fast setting supa glue in a convenient bottle that allows easy, controlled and precise application. Features Easy, controlled application Non-drip glue saver nozzle, reduces waste and mess. Long fine nozzle for precise application Bonds a variety of surfaces Extremely fast setting Dries Clear for clean, neat results Water resistant No clamping necessary No mixing required Maximum strength achieved in 12 hours Only takes 45 seconds to achieve initial bond Non-clog cap Forms a rigid bond Upright self-standing bottle Comfortable to hold Where can this product be used? Ideal for small repair jobs or when immediate results are required. Water resistant not water proof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene. Leather may become hardened or discoloured For interior use only Not suitable for repairing items that are in direct contact with hot liquids Will not permanently bond glass or materials containing alkaline elements. Has no gap filling properties therefore surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Bonds a variety of porous and non-porous surfaces Metals China Rubber Leather Some plastics Wood How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Hold bottle in an upright position. Pierce seal by attaching nozzle and cap and turning clockwise. Remove cap and squeeze gently to apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. (30 seconds). The product grabs within 5-30 seconds, depending on environmental conditions and substrates to be bonded. Allow 30 minutes for sufficient bond strength for practical use. Maximum bond strength reached after 12 hours. Handy tips Cyanoacrylate adhesives can create a white residue on the surface of a substrate if the area is not well ventilated. Clean the affected area with acetone to remove residue. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. Excellent when used with other adhesives, as the temporary tack For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. Acetone (nail polish remover) or Olive oil can also be used to remove Quick Fix from skin. While superglue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Super glues cure more slowly when large amounts are used. For faster cure use sparingly. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Reseal cap in a clockwise direction. Tap bottle lightly on a flat surface to clear excess product from nozzle. To remove excess from substrates, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using thias method. Ensure cap is replaced and store in a cool dry place. Cyanoacrylate based adhesives polymerise in the presence of moisture. Store Upright. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $6.00

  • QuickFix 10 Second Supa Glue Mini Tubes 5ml - 5 Packs x 1ml

    Selleys QuickFix 10 Second Supa Glue Mini Tubes 5ml - 5 Packs x 1ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Single Shot, no mess just throw away Self piercing tube Bonds in 10 seconds Where can this product be used? Ideal for small repair jobs or when immediate results are required For interior projects and repairs Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or materials containing alkaline elements Has no gap filling properties, therefore, surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Metals China Rubber Leather Some plastics

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $6.00

  • Last stock! Prep Multi-Use Adhesive Superseeds PVA Non Toxic Dries Clear 1L

    Prep Prep Multi-Use Adhesive Superseeds PVA Non Toxic Dries Clear 1L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro.  Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $22.98

  • Loctite Super Glue Creative Pen – Precision Application, Fast Bonding for DIY, Craft, and Repairs Loctite Super Glue Creative Pen – Precision Application, Fast Bonding for DIY, Craft, and Repairs

    Loctite Loctite Super Glue Creative Pen – Precision Application, Fast Bonding for DIY, Craft, and Repairs

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    The Loctite Super Glue Creative Pen offers the ultimate solution for precise, fast, and reliable bonding. Its ergonomic pen design ensures a controlled application, perfect for intricate tasks like crafting, DIY projects, or quick household repairs. The pen tip provides pinpoint accuracy, so you can apply just the right amount of glue, reducing mess and waste. Loctite’s fast-drying formula creates a strong bond on materials such as wood, plastic, metal, ceramic, and leather, making it versatile for any project. Whether you're fixing a broken ornament, assembling models, or working on craft projects with the kids, Loctite Super Glue Creative Pen guarantees a professional finish every time. LOCTITE® Super Glue Creative Pen Precision bonding on wood, metal, plastic, rubber, and more. Waterproof, weather-resistant, and shock-resistant. Equipped with a long nozzle and easy-grip squeeze bottle for fast and accurate application. Characteristics: LOCTITE® Super Glue Creative Pen is a one-part instant gel adhesive in a convenient dispenser, perfect for home use. It forms strong bonds between a wide range of common materials, including plastics, rubbers, metals, wood, ceramics, leather, fabrics, cardboard, and paper. Its non-drip formula allows for use on vertical or overhead surfaces. The ergonomic pack design ensures precise application, ideal for bonding smaller items. Bonding Speed: Initial adhesion in 5 to 30 seconds, depending on the substrate. Bond Strength (ISO 4587): 10 to 20 N/mm² (tensile shear) in 12 to 24 hours, depending on the substrate. Water-resistant to EN204-D3 standard. Ceramic bonds can withstand over 50 dishwasher cycles under controlled laboratory conditions. Instructions for Use: Ensure all surfaces to be bonded are clean, dry, and fit closely. Twist the cap clockwise onto the pack until you hear a clicking sound. Do not overtighten; a three-quarter turn is sufficient. Avoid skin contact with the glue. Gently squeeze the rubber panels and apply a minimal amount of adhesive to one surface. Press parts together immediately and hold with hand pressure for at least 1 minute. Allow the bond to set undisturbed for 10 minutes, or preferably overnight, to achieve full bond strength. Protect work surfaces and avoid spills. Remove cured glue with LOCTITE® Glue Remover. For best results, apply at room temperature (15-30°C) with at least 30% relative humidity. After use, wipe the nozzle clean with a tissue, replace the cap, and store in a cool, dry place. Technical Data: Composition: Ethyl cyanoacrylate Appearance: Clear gel Density: 1.1 g/cm³ @ 20°C Viscosity: Gel Safety: Refer to SDS 2669372 Shelf Life: 30 months unopened (stored at 2-8°C) Limitations: Do not use on dusty, dirty, or wet surfaces. Not suitable for bonding polypropylene, polyethylene, PTFE, silicone rubber, glass, glazed surfaces, very soft leather, or foams. Do not use for bonding items exposed to hot liquids or high temperatures for extended periods. Optimum performance is achieved in dry conditions. Storage: Store in a cool, dry place, out of reach of children.   Why choose Glues Australia? We provide premium-quality adhesives like Loctite, backed by our exceptional customer service. With fast, reliable delivery across Australia, you’ll get the products you need when you need them. Shop confidently with Glues Australia, your trusted adhesive supplier!

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $11.57

  • Loctite Super Glue ALL PLASTICS 4ml Loctite Super Glue ALL PLASTICS 4ml

    Loctite Loctite Super Glue ALL PLASTICS 4ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A rapid dual-action adhesive system is specially designed to work on plastic to form resilient, invisible bonds in seconds. Recommended on: Plastic, Porcelain, Metal, Rubber, Leather, Wood, Paper. Properties: Bonds even difficult to bond plastics such as polyethylene (PE) and polypropylene (PP) Bonds in seconds Dries transparent Easy to open, self-piercing and anti-clog cap Suitable for use on most surfaces* Solvent-free * Except Styropor®, car glass and synthetic fibres. Use: Ensure surfaces to be joined are clean, completely dry and close fitting. Using the Surface Activator like a pen apply it to both surfaces and wait 60 seconds to dry. Twist the glue cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $10.67

  • Loctite Easy Repair Pre-mixed Epoxy no mess 5 minute setting 14ml Loctite Easy Repair Pre-mixed Epoxy no mess 5 minute setting 14ml

    Loctite Loctite Easy Repair Pre-mixed Epoxy no mess 5 minute setting 14ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Loctite Epoxy Instant Mix 5 Minute is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 5 minutes and reaches handling strength in 1 hour. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. Loctite Epoxy Instant Mix 5 Minute does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on: Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fibreglass, concrete and stone Can be combined with fibreglass cloth for a durable patch Great for crafting projects Properties Will not crack when drilled Can be tinted to match surrounding materials Water resistant: can be used outdoors Does not shrink   One-time application Convenient instant mix syringe  Consistently dispenses equal, uniformly mixed amounts of each component Sets in 5 minutes  Quick completion of the project How to Use: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from the centre of the plunger. Turn nozzle end up and pull the plunger back slightly allowing air bubbles to rise to the top. Snap off and discard end of the syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto the surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $9.23

  • Araldite 5 Minute Epoxy Adhesive With Self Mixing Nozzle 14ml

    Selleys Araldite 5 Minute Epoxy Adhesive With Self Mixing Nozzle 14ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance   Appearance: Clear with a slight yellow tinge   Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops   What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather   How to use this product: General Use -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick.   Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $8.00

  • Packshot of Ryobi ONE+ 18V Dual Temperature Glue Gun Tool Only

    Ryobi Ryobi ONE+ 18V Dual Temperature Glue Gun Tool Only

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Ryobi ONE+ 18V Dual Temperature Hot Glue Gun – Tool Only delivers precise and consistent adhesive application for DIY, craft, and repair projects. Designed for versatility, it features dual temperature control and cordless convenience, making it ideal for home and professional use. Key Features Dual temperature settings: Choose between 120°C for delicate materials and 160°C for stronger bonding applications. Fast heat-up time: Ready to use in approximately 3 minutes for quick, efficient work. Long nozzle design: Provides greater reach and precision when gluing hard-to-access areas. Drip tray and ergonomic handle: Keeps your workspace clean and provides comfort during extended use. LED indicator: Red light shows warming up, green light indicates ready-to-use. Part of the Ryobi ONE+ system: Compatible with all Ryobi 18V ONE+ batteries (sold separately). Specifications Voltage: 18V High Temperature Mode: 160°C Low Temperature Mode: 120°C Glue Stick Diameter: 11–12 mm Nozzle Hole: 3.0 mm Heat-Up Time: Approx. 3 minutes Weight (without battery): 0.4 kg Included Ryobi ONE+ 18V Dual Temperature Glue Gun (Tool Only) User Manual Compatible Batteries (Sold Separately) RB18L13, RB18L15, RB18L20, RB18L25, RB18L40, RB18L50, RB18L60A, RB18L90A, and more from the Ryobi ONE+ range. Safety and Maintenance Use only original accessories and spare parts. Avoid contact with hot surfaces. Do not immerse the tool or battery in liquid. Clean using a dry cloth and store with batteries removed when not in use for extended periods. Imported by Techtronic Industries Australia Pty Ltd, Mount Waverley VIC 3149.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $103.95

  • Packshot of Ozito PXC 18V Cordless Glue Gun 11mm Skin Only

    Ozito Ozito PXC 18V Cordless Glue Gun 11mm Skin Only

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Make fast, tidy bonds on timber, plastics, ceramics and more with the Ozito Power X Change 18V Cordless Glue Gun. It heats up in about 120 seconds and uses standard 11 mm glue sticks, so you can tackle DIY fixes, craft projects and light repairs without cords getting in the way. Why you will love it Cordless convenience for indoor and outdoor jobs Quick heat up in about 120 seconds for less waiting Consistent flow control trigger for neat, accurate beads and dots Interchangeable nozzles round and precision tips included for detail work LED worklight helps you see the glue line clearly Auto shut off after inactivity to help conserve battery Part of Ozito PXC one battery system across tools and garden gear What is in the box Ozito PXC Cordless Glue Gun (skin only) 5 x 11 mm glue sticks Round nozzle and precision nozzle 13 mm hex spanner Ideal for Timber trims, skirting, craft and hobby builds Quick fixes on ceramics and some plastics Cardboard, fabric trims and school projects Key specifications Battery platform Ozito Power X Change 18V Pre heating time Approx. 120 seconds Max heating temperature 170°C Glue stick size 11 mm diameter Weight 0.4 kg Auto power off Yes, after inactivity Battery and charger sold separately. How to use Insert a charged PXC 18V battery and press the on or off button. Wait until the status light indicates ready, about 2 minutes. Feed an 11 mm glue stick and squeeze the trigger to apply glue. Press surfaces together straight away and hold for about 30 seconds. Stand the tool upright on the battery between uses and let it cool before storage. Good to know Use the precision nozzle for fine detail and the round nozzle for general bonding. Work on clean, dry surfaces for the best adhesion. Wear eye protection, take care around hot glue and hot nozzle areas. Warranty Tool is covered by a 5 year replacement warranty for DIY use. PXC lithium batteries and chargers are covered by a 36 month warranty. Keep your proof of purchase.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $52.48

  • Packshot of Stanley 12mm 240V Corded Hot Glue Gun 25W

    Stanley Stanley 12mm 240V Corded Hot Glue Gun 25W

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Stanley 12mm 240V Corded Hot Glue Gun 25W Get clean, reliable bonds for crafts, quick household fixes, packaging, and light DIY with the Stanley 12mm Corded Hot Glue Gun. Its 25W heating element warms up efficiently for steady glue flow, while the compact body and ergonomic trigger deliver comfortable, controlled application on a wide range of surfaces. Why choose this glue gun Trusted Stanley build for everyday projects and repairs Consistent glue output for neat, repeatable results Easy to handle for beginners and experienced makers Key features 12 mm glue sticks for great coverage and fewer reloads 25W heating element for steady melt and controlled flow Ergonomic trigger that reduces hand fatigue on longer runs Built in stand and nozzle shroud to help keep benches tidy 240V corded power for uninterrupted operation Great for Cardboard, paper, fabric, felt, foam, ribbons, and craft materials Wood trims, light plastics, small fixtures, and packaging General household touch ups and temporary jigs How to use Insert a 12 mm glue stick into the feed port. Plug into a 240V outlet and allow the tool to preheat. A few minutes is typical. Gently squeeze the trigger to dispense glue. Apply in small beads or dots. Press parts together while the adhesive is hot. Hold until initial grab occurs. Rest the tool on the built in stand when not dispensing. Unplug after use. Compatibility Uses standard 12 mm hot melt glue sticks. Works with multi purpose, high tack, wood, and craft grade sticks. For heat sensitive substrates such as very thin plastics or delicate fabrics, test on a small area first. Specifications Power 25W Voltage 240V AC Glue stick size 12 mm diameter Nozzle Precision tip with protective shroud Stand Integrated flip down stand Cord Mains corded Typical applications Crafts, packaging, light repairs What is in the box Stanley 25W 12 mm Hot Glue Gun User guide Glue sticks sold separately Helpful tips Keep the nozzle clean by wiping away stringing while warm using a scrap of cardboard. For porous materials like fabric or raw timber, apply a slightly thicker bead. For smoother finishes on visible joints, apply small dots and press evenly. Safety and care Hot melt adhesive and nozzle become very hot. Avoid contact with skin. Use on a stable, heat resistant surface. Keep out of reach of children. Unplug after use and allow to cool before storage. FAQ Q: Can I use smaller mini sticks? A: This tool is designed for 12 mm sticks. Using other sizes can cause feed issues. Q: How long do I have to position parts? A: Open time varies by stick type and temperature. Work quickly and test first on your material. Note: Always test bond strength and heat suitability on an offcut before full application.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $44.10

  • Packshot of Selleys Araldite Extra Time Epoxy Adhesive 200ml

    Selleys Selleys Araldite Extra Time Epoxy Adhesive 200ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Araldite Extra Time Epoxy Adhesive 200ml Araldite Extra Time is a strong two part epoxy that gives you an extended working time of up to 60 minutes. It is ideal for complex or multi piece assemblies where accurate positioning matters. Once cured it forms a tough, durable bond that dries translucent. Why you will love it Extended working time of 60 minutes for precise assembly Holds up to 150 kg per cm² when fully cured on clean, abraded steel Dries translucent for a neat finish Versatile bonding across common materials Suitable materials Wood, metal, masonry, china, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. Pre test on leather and rubber for suitability. Typical uses Furniture repairs and assemblies Fixing metal or timber components General household, hobby, and craft bonding Repairs on masonry, ceramics, and glass where a clear finish is preferred Directions Surface prep: abrade, clean, and dry both surfaces. Pierce each tube using the spike in the cap. Dispense equal parts onto a clean disposable surface. Mix thoroughly. Leave for 5 minutes, then mix again before applying. Mixed glue is usable for about 1 hour at 20°C. Do not use the plastic blister to mix. Apply to both surfaces and join. Support if needed to prevent movement. Avoid strain for 6 to 8 hours. Full strength develops after 24 to 72 hours depending on conditions. Replace caps on the correct tubes to avoid cross contamination. Clean up Wipe away uncured adhesive with acetone. Once cured, mechanical removal is required. Key specs Technology Two part epoxy Working time Up to 60 minutes Initial handling 6 to 8 hours Full cure 24 to 72 hours Bond strength Up to 150 kg per cm² on abraded steel when fully cured Appearance Dries translucent Temperature resistance Up to 80°C. Bond may soften above this but strength returns when temperature normalises. Pack size 200 ml Good to know Allow longer bonding times in colder weather. Product may discolor with UV exposure. Store in a cool dry place.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $66.48

  • Packshot of Selleys Araldite Rapid Epoxy Adhesive 14mL

    Selleys Selleys Araldite Rapid Epoxy Adhesive 14mL

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Araldite Rapid Epoxy Adhesive 14 mL Fast-setting, two-part epoxy for quick, durable repairs at home, in the workshop, or on site. The self-mixing syringe makes application clean and precise, setting in about 90 seconds and reaching handling strength soon after. Dries translucent for a neat finish. Key benefits Sets in approximately 90 seconds for rapid fixes High strength bond up to 75 kg/cm² when fully cured Dries translucent for low-visibility repairs Self-mixing nozzle for easy, accurate application Versatile bonding across common materials Best for Everyday repairs and small assemblies Fixing chipped ceramics and china Metal, glass, leather, rubber, and many plastics Suitable materials China, metal, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. How to use Prep Abrade, clean, and dry both surfaces. Attach nozzle Remove cap, fit and lock the self-mixing nozzle, then purge a small amount until evenly mixed. Apply Spread adhesive on both surfaces and join within 1 minute. Hold Support the bond for about 10 minutes to prevent movement. Cure Maximum strength develops after about 16 hours. Allow longer in cold conditions. Clean up Wipe away uncured adhesive with acetone. Remove and dispose of the used mixing nozzle before the adhesive sets in the tip. Technical details Technology Two-part epoxy Set time About 90 seconds Handling time Approximately 10 minutes Full cure About 16 hours Colour when dry Translucent Temperature resistance Up to 60 °C Pack size 14 mL self-mixing syringe Good to know Bond may soften above 60 °C and regains strength when cooled. Pre-test on leather and rubber to confirm suitability. May discolor with prolonged UV exposure. Store in a cool, dry place. Replace cap after removing the used nozzle. Safety Follow the safety directions on the packaging. Use in a well-ventilated area and avoid skin contact. Keep out of reach of children.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $16.89

  • Packshot of Tarzan’s Grip Multi-Purpose General Adhesive 250 g

    Selleys Tarzan’s Grip Multi-Purpose General Adhesive 250 g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Tarzan’s Grip Multi-Purpose General Adhesive 250 g is a reliable versatile contact style adhesive for crafts and household fixes chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 250 g pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Tarzan's Grip Grip for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Multi-Purpose General Adhesive 250 g has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bonding fabric, leather, and rubber General craft builds Light repairs around the home Suitable surfaces The adhesive works well on the following surface types when properly prepared: Leather and canvas Rubber trim Timber and some plastics Card and foam board Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of allow adhesive to tack before assembly as directed on pack. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Forms a tough, flexible bond after solvent evaporation and cure. Press parts together firmly for best adhesion. Temperature and environmental performance Keep away from flames and high heat during application. Once cured, it resists typical temperatures. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Use appropriate solvent on uncured adhesive, working in a ventilated space. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Replace cap after each use to reduce skinning. Store below 30 C. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $13.64

  • Bostik Quick Glu Instant Fix Bond Spray 25 g Bostik Quick Glu Instant Fix Bond Spray 25 g

    Bostik Bostik Quick Glu Instant Fix Bond Spray 25 g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Get fast and reliable adhesion with Bostik Quick Glu Instant Fix Bond Spray. This 25g spray adhesive provides a strong, clear and lasting bond suitable for a wide range of materials used in craft, home and office projects. Key Features Instant bonding for quick and easy use Dries clear for a neat and professional finish Acid free formula that resists yellowing over time Works on wood, metal, ceramic, leather, paper and many plastics (not suitable for polyethylene or polypropylene) Compact 25g size ideal for small jobs and easy storage How to Use Ensure surfaces are clean, dry and free from grease or dust. Shake the can well before each use. Hold the can 15 to 20 cm from the surface and apply a light, even coat. Wait a few seconds until tacky before joining the surfaces. Press firmly together and hold for a few seconds for best results. After use, clear the nozzle by spraying briefly while holding the can upside down. Recommended Applications Arts and crafts projects DIY home repairs Paper, cardboard, leather and wood bonding Quick fixes requiring a clear and clean finish Safety and Storage Use only in well ventilated areas and avoid inhaling vapours. Keep away from heat, sparks and open flames as the product is flammable. Store in a cool, dry place away from direct sunlight. Keep out of reach of children. Bostik Quick Glu Instant Fix Bond Spray delivers a convenient and efficient solution for fast bonding on a wide variety of materials.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $8.50

  • Bostik Multi Purpose Spray Adhesive 350g

    Bostik Bostik Multi Purpose Spray Adhesive 350g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Bostik Spray Adhesive is a clear, fast-tack, multi purpose aerosol glue designed for quick and easy bonding of lightweight materials. Ideal for craft, school, office, and general household repairs where a neat, even spray is preferred. Why you’ll love it Fast tack with strong initial grab Clear, low-mess spray pattern for even coverage Adjustable bond: reposition briefly, then press firm Non-staining on most materials Great for large areas and edge-to-edge laminations Suitable materials Paper, cardboard, photos, craft foam, felt, fabric, foil, leather, cork, many plastics, wood, and light laminates. Always test on delicate or coated surfaces. Typical uses Mounting posters, photos, and presentations Craft projects and scrapbooking Attaching fabric or felt to displays Temporary positioning before stitching or stapling How to use Ensure surfaces are clean, dry, and free of dust or oil. Shake the can well before and during use. Hold 15–20 cm from the surface and spray a light, even coat. For temporary bonds, spray one surface only and join after 10–30 seconds tack time. For stronger bonds, spray both surfaces, allow to go tacky, then press together with firm, even pressure. Drying and cure Tack time: typically 10–60 seconds depending on coat weight and conditions Handling strength: a few minutes Full bond development: 24 hours Clean up While wet, wipe overspray from hard surfaces with a suitable adhesive remover or mineral turpentine, then wash with warm soapy water. Test cleaners on an inconspicuous area first. Good to know Clear finish when dry Best at room temperature with good ventilation Not recommended for high heat, heavy structural loads, or polyethylene and polypropylene unless tested Storage and safety Store upright in a cool, dry place away from heat and flame. Use only in well ventilated areas. Avoid inhalation and contact with eyes or skin. Keep out of reach of children. Press nozzle briefly upside down after use to clear. Specifications Format: Aerosol spray Colour: Clear Size: 350 g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $35.00

  • Last stock! Bostik Super Glue Gel Precision Bond 3g

    Bostik Bostik Super Glue Gel Precision Bond 3g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Bostik Super Glue Gel is a fast setting, non drip adhesive that stays where you put it for precise, clean bonds. The thixotropic gel formula is ideal for vertical surfaces and small gap filling, delivering reliable results on everyday repairs and crafts. Key features Fast setting gel for controlled application Non drip formula for vertical and overhead surfaces Small gap filling for close fitting parts Strong bond on many common materials Clear finish for neat repairs Ideal for Metal, rubber, most hard plastics, wood, ceramics, porcelain Small household repairs, models, craft and DIY fixes Precision bonding where liquid super glue may run Not suitable for Polyethylene, polypropylene, PTFE Very flexible materials or items regularly exposed to water immersion Food contact surfaces or aquarium use Directions Ensure surfaces are clean, dry and close fitting. Lightly roughen smooth surfaces if possible. Remove cap and apply a small bead of gel to one surface. A little goes a long way. Join parts immediately and hold firmly until set. Avoid moving the bond during curing. Allow the repair to rest for several minutes before light handling and longer for full strength. Handy tips Test on an inconspicuous area first. Use sparingly. Excess adhesive can slow cure. For porous materials, a second application may improve the bond. Clean up Wipe fresh squeeze out immediately. Once cured, carefully remove excess with a sharp blade. Adhesive may whiten on some surfaces if excess is left to cure. Storage and safety Close cap tightly after use and store upright in a cool, dry place. Bonds skin in seconds. Wear care when handling. If skin bonding occurs, do not pull apart. Soak in warm soapy water and gently roll apart. Use in a well ventilated area and keep out of reach of children.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $6.47

  • Bostik Repair All Multi-Purpose Adhesive 20ml Bostik Repair All Multi-Purpose Adhesive 20ml

    Bostik Bostik Repair All Multi-Purpose Adhesive 20ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Bostik Repair All is a clear, multi-purpose adhesive for quick, durable repairs around the home, garage, and workshop. It bonds strongly, remains slightly flexible, and is water resistant once cured, making it suitable for everyday fixes and craft projects. Why you will love it Strong, long lasting bond Dries clear for a neat finish Water resistant once fully cured Flexible bond helps absorb vibration Suitable for indoor and outdoor use Works on Metal, wood, ceramics, glass, most rigid plastics, rubber, leather, fabric, and more. Always test on delicate or unknown materials first. Ideal for Household repairs and DIY Craft, hobbies, and school projects Fixing ornaments, toys, trims, and fittings Directions Ensure surfaces are clean, dry, and free of dust or grease. Lightly roughen smooth surfaces. Apply a thin even layer to one surface. Join parts together and press firmly. Support or clamp if needed. Wipe away any squeeze out immediately with a cloth dampened with solvent suitable for the substrate. Allow to set undisturbed. Handling strength is typically reached within hours. Full cure is usually achieved after 24 hours depending on bead size, temperature, and humidity. Clean up Uncured adhesive can be removed with a suitable solvent. Cured adhesive is best removed mechanically by trimming or carefully scraping. Good to know Not recommended for polyethylene, polypropylene, PTFE, or surfaces that will be in constant water immersion. Avoid contact with food or drinking water surfaces. Store upright in a cool dry place with cap tightly closed. Key details Brand Bostik Product Repair All Appearance Clear when dry Finish Flexible Water Resistance Yes, once cured Pack Size 20ml Always read the label and follow safety instructions. Keep out of reach of children.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $14.50

  • Bostik Leather Repair Glue Ultra-Clear Flexible Bond 20 mL Bostik Leather Repair Glue Ultra-Clear Flexible Bond 20 mL

    Bostik Bostik Leather Repair Glue Ultra-Clear Flexible Bond 20 mL

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Bring Your Leather Items Back to Life Restore your favourite leather goods such as shoes, belts, bags, and upholstery with confidence using Bostik Leather Repair Glue. This precision adhesive delivers a strong, flexible, and water-resistant bond that dries crystal clear. Key Features Ultra strong and long lasting bond for real and imitation leather Flexible and clear finish with no visible residue Resistant to water and heat up to approximately 60 °C Precision application through fine nozzle squeeze tube Multi material versatility suitable for leather, PVC, felt, canvas, some plastics, wood, and metal How to Use Ensure surfaces are clean, dry, and free from dust, oil, or old adhesive residue. For leather surfaces, avoid applying to the shiny side to prevent marks. Apply a thin film of glue to one surface. For non porous materials, apply to both surfaces. Press the surfaces together firmly. The bond sets almost instantly and reaches full strength in about 24 hours. Replace the cap immediately after use to prevent the tube from drying out. Tips and Care For best adhesion, lightly roughen smooth or shiny surfaces with fine sandpaper before gluing. Avoid stressing the repair before full cure. To remove unwanted glue, use acetone or nail polish remover on a small hidden area first. Technical Specs and Safety Form: Clear solvent based polyurethane adhesive Heat resistance: up to approximately 60 °C Highly flammable. Keep away from heat, sparks, and flame. Always follow manufacturer instructions and safety guidance. Use in a well ventilated area, wear protective gloves, and avoid contact with skin or eyes. Packaging Size: 20 mL tube

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $9.79

  • LOCTITE Super Glue All Plastics Clear – 2 g + 4 ml Kit LOCTITE Super Glue All Plastics Clear – 2 g + 4 ml Kit

    Loctite LOCTITE Super Glue All Plastics Clear – 2 g + 4 ml Kit

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Overview LOCTITE Super Glue All Plastics is a rapid dual-action adhesive kit featuring a precision super glue and a surface activator pen. Engineered to bond difficult plastics such as polyethylene (PE), polypropylene (PP) and PTFE, it forms clear, resilient bonds in seconds and resists water, most household chemicals and freezing temperatures. Ideal for repairs on toys, cameras, small automotive parts, wiper blades, rubber seals, figurines and other plastic components. Advanced bonding system: activator primes the surface; glue delivers high strength. Fuses hard-to-bond plastics: effective on PE, PP, PTFE and more. Fast & clear: sets in seconds, dries transparent for nearly invisible repairs. Durable: water-resistant and suitable for cold conditions. Surface Preparation Ensure both surfaces are clean, dry and close-fitting. Remove grease, oil, dust or loose particles. For best adhesion on very smooth plastics, lightly roughen with fine-grade sandpaper and wipe clean. Avoid use on soft foams, expanded polystyrene or highly porous materials. Always test on a small, inconspicuous area if unsure about compatibility. Application Instructions Prime with activator: Apply one or two thin coats to both bonding surfaces, ensuring full coverage. Re-cap the activator pen immediately. Allow to dry/react for 1–2 minutes. Apply adhesive: Place a minimal drop of glue on one surface only. Bring parts together immediately and hold firm pressure for at least 1 minute. Avoid shifting once contact is made. Cure: Leave undisturbed for 10 minutes. Full bond strength develops after 12–24 hours at room temperature. Coverage & Performance Only a thin film is required—one drop bonds most small mating areas. Initial handling strength is typically achieved within 5–30 seconds depending on substrates and conditions. Drying & Setting Time Initial set: 5–30 seconds* Handling time: ~1 minute Full cure: 12–24 hours Recommended conditions: 15–30 °C and ≥30% relative humidity *Setting and cure times vary with substrate, joint fit, temperature and humidity. Clean-Up & Storage Wipe nozzle to remove excess adhesive and replace caps immediately after use. Store upright in a cool, dry place away from sunlight and moisture. Do not refrigerate. Shelf life (unopened and properly stored): up to 18 months. Limitations Not recommended for glass, very flexible materials, soft foams or highly porous substrates. Not suitable for continuous water immersion or high-heat applications. For indoor use or dry environments; test before critical repairs. Safety & Handling Contains cyanoacrylate. Bonds skin and eyes in seconds. Avoid contact. Use in a well-ventilated area; consider gloves and eye protection. If skin is bonded, do not pull apart—soak in warm, soapy water and gently roll/separate. Acetone may assist on non-sensitive skin; avoid on plastics. If in eyes, rinse cautiously with water and seek medical attention immediately. Keep out of reach of children. Technical Data Product Type Two-part system: Activator + Cyanoacrylate Adhesive Substrates PE, PP, PTFE, many rigid plastics, rubber, selected metals Appearance Clear (dries transparent) Packaging Size 2 g adhesive + 4 ml activator Initial Set 5–30 seconds (substrate dependent) Full Cure 12–24 hours at ambient conditions Temperature Range Approx. −50 °C to +80 °C (typical for cured cyanoacrylates) Cleanup Mechanical removal once cured; avoid solvents on sensitive plastics What’s Included LOCTITE Super Glue (2 g) Surface Activator Pen (4 ml) Always follow on-pack directions. Performance will vary with materials, joint design and environmental conditions.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $9.64

  • Last stock! Bostik Fabric Glue 20ml - Clear Flexible Permanent, Washable, Heat-Resistant Craft Adhesive for Clothing Repairs, Hems, Badges & Soft Furnishings Bostik Fabric Glue 20ml - Clear Flexible Permanent, Washable, Heat-Resistant Craft Adhesive for Clothing Repairs, Hems, Badges & Soft Furnishings

    Bostik Bostik Fabric Glue 20ml - Clear Flexible Permanent, Washable, Heat-Resistant Craft Adhesive for Clothing Repairs, Hems, Badges & Soft Furnishings

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Clear Flexible Fabric Glue A versatile, water-based fabric adhesive designed for clothing repairs, craft projects, and soft furnishings. It forms a strong, long-lasting, flexible bond on most porous fabrics and dries clear in thin films for a neat, professional finish. Once fully cured, the bond is machine washable, can be tumble dried, and is safe to iron. Key Features Permanent, flexible bond for clothing and crafts Water-based, low odour formula Dries clear in thin applications Machine washable and tumble-dry compatible after full cure Heat resistant—safe to iron over the bonded area Easy squeeze application; cleans up with warm soapy water while wet Ideal Uses Hems, trouser turn-ups, and pocket repairs Attaching cloth labels, badges, and patches Securing frayed lace ends and trims Curtain hems and decorative soft furnishing accents General fabric repairs on cotton, denim, linen, felt, leather and similar porous textiles Directions Preparation: Ensure surfaces are clean, dry, and free from dust or grease. At least one surface must be porous. Test first: Trial on an off-cut or hidden area, especially with light or open-weave fabrics. Apply: Spread a thin, even layer to the non-visible side or back of the fabric. Join parts and press for several seconds. Initial handling: Light handling is typically possible after about 1 minute; avoid stressing the bond. Optional set boost: For improved bonding, gently iron-press ~5 minutes after gluing (use a pressing cloth). Full cure: Reaches full effective strength after 24 hours. After curing, the item may be machine washed, tumble dried, and ironed. Clean-Up While wet: Wipe away with warm, soapy water; repeat if needed, rinse and dry. When dry on smooth, non-porous surfaces: Gently rub off or use warm, soapy water. When dry on fabrics: Difficult to remove—prevent excess and work carefully. Compatibility & Notes Best on porous textiles: cotton, denim, linen, felt, leather, and similar materials. Not suitable for non-porous materials or 100% nylon/polyester fabrics. Avoid heavy application or excessive pressure on light or open-weave fabrics to minimise show-through or darkening. Specifications Chemistry Acrylic copolymer (water-based) Appearance Milky white liquid; dries clear in thin films Density 1.07 ± 0.02 g/cm³ Solids Content 61–63% Viscosity Up to ~1,000 cps pH 4–6 Initial Handling Time ~1 minute (varies with material, temperature, humidity) Full Cure / Maximum Strength ~24 hours Washability & Heat Machine washable; tumble dry and iron once fully cured Clean-Up (Wet) Warm soapy water Pack Size 20 mL (blister) Storage Cool, dry place around 20 °C; keep container tightly closed; protect from moisture Shelf Life Up to 18 months from manufacturing date (unopened, stored as directed) Not Suitable For 100% nylon, 100% polyester, non-porous materials, very fine/delicate fabrics (e.g., some silks, wools, linens)

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $13.98

  • Loctite Super Glue XXL for frequent usage Multi material 20g Loctite Super Glue XXL for frequent usage Multi material 20g

    Loctite Loctite Super Glue XXL for frequent usage Multi material 20g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $23.00

  • Uni-Pro Large Snap Blade Knife

    Uni-Pro Uni-Pro Large Snap Blade Knife

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    The UNi-PRO snap blade knife is the perfect tool for all your tasks. From opening packages to cutting string, this durable and convenient multi-purpose knife will make life easier!

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $6.50

  • Last stock! UHU Super Strong & Safe - No immediate finger bonding 7g UHU Super Strong & Safe - No immediate finger bonding 7g

    UHU UHU Super Strong & Safe - No immediate finger bonding 7g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    UHU All Purpose Adhesives Super Strong & Safe, the super strong and super fast adhesive, which is adjustable - no instant finger bonding. Suitable for virtually all flexible, solid, porous and non-porous materials. Formula patented. Withstands vibrations and tremors. Moisture and heat resistant from -50°C to +100°C. Materials Universal - glues porcelain, ceramic, many plastic materials, metal, wood, glass, leather, rubber, Styrofoam®, paper, cardboard. Not suitable for leather clothing, textiles, PE and PP. Use and Handling Instructions Surfaces to be stuck together must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. Press parts together. Glue joint remains correctable for approx. 20 seconds. The thinner the film of adhesive, the stronger the bond.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $10.74

  • Last stock! UHU Super Glue Ultra Fast Gel 3ml UHU Super Glue Ultra Fast Gel 3ml

    UHU UHU Super Glue Ultra Fast Gel 3ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    PROPERTIES Extra strong Fast but temporarily adjustable Does not drip Ideal for porous materials and vertical surfaces Dishwasher proof and water resistant APPLICATION SUITABLE FOR: Ideal for small-area bonds. Glues almost all solid and flexible materials like ceramics, leather, rubber, many plastics (such as rigid PVC, ABS, PS, Plexiglas®, polycarbonate (Makrolon®), and phenolic resins (Bakelite®)), porcelain, metal, wood, cork, felt, and cloth (check suitability first). Only partly suitable for glass (over a certain period of time the bond becomes brittle, causing it to weaken). Ideal for porous materials. NOT SUITABLE FOR: Not suitable for PE, PP, silicone resins, PTFE, Styrofoam®, fabrics and leather clothing. BEFORE USE: Working conditions Do not use at temperatures below +10 °C. The glue responds best to an air humidity level of 50-70 %. Surface requirements Surfaces to be glued must be clean, dry, and free of dust and grease, and must fit exactly. Preliminary surface treatment Any dust, oil, grease, wax or separating agent should be thoroughly removed from the surfaces to be stuck together. The best way to achieve this is to rub the parts a number of times with appropriate solvents, such as acetone (if suitable for the material – check first!). For metals and metal alloys it is usually sufficient to roughen the surface using emery paper or by grinding or brushing. DURING USE: Directions for use 1. To pierce the membrane, turn the cap clockwise firmly onto the tube. Tip: do not press the tube while piercing. 2. Unscrew the cap to reveal the applicator. Apply the adhesive directly from the tube, using the nozzle, as thinly as possible onto one side (too much glue slows down the curing process significantly). Press parts together immediately. After use, clean nozzle with a dry tissue and replace cap. Advice When glueing at low humidity, curing time can be shortened by briefly breathing onto one of the parts to be assembled. The best glueing results are reached at room temperature. Points of attention Contains cyanoacrylate. Bonds skin and eyelids together in seconds. If product comes into contact with the eyes, rinse immediately with plenty of water and seek medical advice. In case of contact with skin, glue can be dissolved by soaking in warm soapy water. Then apply a skin cream. May cause respiratory irritation. Avoid breathing vapours. Keep out of the reach of children. AFTER USE: Stains/residue Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue but very slowly (check suitability first). Storage conditions Store in a dry, cool, frost-free place. Storage below +5 °C (in refrigerator) ensures maximum shelf life.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $7.00

  • UHU All Plastics Strong Water Resistant transparent Adhesive 30g

    UHU UHU All Plastics Strong Water Resistant transparent Adhesive 30g

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Powerful universal adhesive for most plastics. Cold welding technology for a perfect bond. Ideal for multi-purpose domestic applications, handicraft work, repairs and model building. The hard but flexible adhesive film remains transparent. Water and temperature resistant. Toluene free. YOU CAN FIX IT! Glues most usual plastic materials (ABS, Plexiglas®, hard PVC...), also in combination with wood, metal, glass and ceramics. *Not suitable for PE, PP and Styrofoam.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $12.77

  • The Original Super Glue Super Glue Gel x 3 Tubes of 2g each Fast curing non drips 6g The Original Super Glue Super Glue Gel x 3 Tubes of 2g each Fast curing non drips 6g

    The Original Super Glue The Original Super Glue Super Glue Gel x 3 Tubes of 2g each Fast curing non drips 6g

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Super Glue gel's thick viscosity is perfect for clean, vertical, porous (wood, hard leather and porcelain) surfaces. Gels allow for a more accurate application as they do not drip or run. Works best on:  Leather Metal Vinyl Rubber Most plastics Aluminum Ceramics Hard & Soft Wood China Pottery Jewelry   NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rear view mirrors or parts that are subjected to great shock or continuous immersion in water. Properties: Initial color: Clear, transparent Final color: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820C) Use: NOTE: For best results, surfaces should be clean and dry and items should fit together well. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Carefully follow tube-opening directions on package. Unscrew cap while keeping tube pointed away from the face. 2. Apply to one surface, using 1 drop per square inch of surface. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe the top of nozzle if the adhesive has accumulated before recapping tube securely after use. Storage: Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN. 

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $18.00

  • The Original Super Glue High Performance Future Glue 5g Brush On Bonds Instantly Multiple Surfaces 5g The Original Super Glue High Performance Future Glue 5g Brush On Bonds Instantly Multiple Surfaces 5g

    The Original Super Glue The Original Super Glue High Performance Future Glue 5g Brush On Bonds Instantly Multiple Surfaces 5g

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    High Performance Future Glue® Brush-On evenly and safely coats most surfaces while eliminating skin contact. Perfect for small and large surfaces needing a thorough coat of Future Glue®. Its instant bonding power can be used for almost all porous and non-porous materials. Its powerful adhesive formula works on dirty, greasy surfaces, and resists high and low temperatures as well as most chemicals. Pacer Technology Super Glue’s Future Glue Brush-On (14204, 15099, 15111) is a quick-setting adhesive that works on oily & dirty surfaces to bond materials, such as: Jewelry Metal Leather Ceramic Most Plastics Rubber Aluminum China Porcelain Hard & soft wood Pottery NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rear view mirrors or parts that are subjected to great shock or continuous immersion in water. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650  to 1800F  (-540  to 820 C) Use: For best results, surfaces should be clean and dry. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Carefully follow tube-opening directions on package. Unscrew cap while keeping tube pointed away from the face. 2. Apply to one surface, using 1 drop per square inch of surface. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe the top of nozzle if the adhesive has accumulated before recapping tube securely after use. STORAGE AND SHELF LIFE: Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause a burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN. 

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $29.95

  • The Original Super Glue Gel Super Glue with Accutool precision applicator 5g The Original Super Glue Gel Super Glue with Accutool precision applicator 5g

    The Original Super Glue The Original Super Glue Gel Super Glue with Accutool precision applicator 5g

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    This new, innovative dispensing system allows for accurate control while utilizing an advanced formula of the Super Glue Corporation's signature product cyanoacrylate (Super Glue GEL). The easy to hold applicator design allows for either continuous stream or single drop control. No more sticky fingers! This glue works great when adhering to porous or vertical surfaces. It will not drip or run! Works best on: Aluminum Ceramic China Hard & Soft Wood Jewelry Metal Most Plastics Pottery Rubber Vinyl Pacer Technology AccuTool Gel (19026) is a quick-setting, non-sagging gel adhesive that fills gaps & works best on: Leather Metal Vinyl Rubber Most plastics Aluminium Ceramics Hard & Soft Wood China Pottery Jewellery Fingernails NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rearview mirrors or parts that are subjected to great shock or continuous immersion in water. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650  to 1800 F (-540 to 820C) Use: For best results, items should fit closely together. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Refer to package for special opening instructions – has Self Piercing “Ratchet” Opener. After opening, remove the outer cap for use. 2. Apply sparingly to one surface using 1 drop per square inch. Assemble parts and hold together with pressure for 15 seconds or until set. 3. After use, wipe tip before replacing cap to prevent sticking and close bottle securely. Storage and Shelf Life: Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause a burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN. 

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $9.95

  • The Original Super Glue Fix-All Adhesive Water Resistant 18.4ml The Original Super Glue Fix-All Adhesive Water Resistant 18.4ml

    The Original Super Glue The Original Super Glue Fix-All Adhesive Water Resistant 18.4ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Fix-All Adhesive is a great all-purpose solvent glue and sealer. It seals and repairs almost any surface easily and quickly. A great product for gluing wood, fabric, brick, canvas, and concrete. Also repairs tears and helps fill cracks and holes. Pacer Technology Super Glue Fix-All Adhesive (T-FA) is a single component adhesive that glues, seals and repairs and is best used for: • Metal • Plastics • Ceramics • Wood • Glass • Rubber • Fabrics • Brick • Leather • Canvas • Concrete • China • Vinyl • Porous materials • Non-Porous materials Properties: Initial colour: Clear Final colour: Clear to light yellow Open Time: 10 minutes Dry Time: 30 minutes Handling Time: 3 hours Full Strength: 24 hours Operating Temperature Range: -200 to 1500F (-290 to 660C) Instructions: Use in a well-ventilated area. Protect work surfaces. As a glue: Apply to both surfaces and let dry 10 minutes. Press parts together. Full cure in 24 hours. For rough, uneven or very porous surfaces, apply a thick layer to both surfaces and wait 30 minutes before joining parts. As a sealer: Fill crack or hole with extra amounts of Fix-All and allow to dry. Add additional adhesive as needed. For repair: To repair vinyl, rubber or fabric tears, apply Fix-All with a spatula behind, through and above the tear. Hold sides together using a strong piece of tape across the tear to hold it tightly. Remove tape after 3 hours. Remove excess with a rubber eraser. Note: when thick layers are required it is better to apply a number of thin coats. Allow curing for 3 hours before handling. Full cure in 24 hours. Notes: Solvents may evaporate from bottle or tube if left open for prolonged periods. Not recommended for Teflon, Polyethylene or Polypropylene bonding. Avoid constant submergence in water and exposure to extremely high temperatures after cure. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains xylene, naphtha and ethylbenzene. DANGER: liquid adhesive is Extremely Flammable. Harmful or fatal if swallowed. Vapour harmful. Avoid breathing vapours. Use and store in a well-ventilated area away from heat, sparks or flame. May cause eye/skin irritation. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN. 

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $25.00

  • The Original Super Glue Contact Cement Flexible Contact Adhesive 29.5ml The Original Super Glue Contact Cement Flexible Contact Adhesive 29.5ml

    The Original Super Glue The Original Super Glue Contact Cement Flexible Contact Adhesive 29.5ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Contact Cement is a flexible acrylic contact adhesive used to bond tile, rubber, wood, metal, formica, most plastics and much more. Pacer Technology Super Glue Contact Cement (T-CC) is a single component flexible acrylic contact adhesive that remains flexible after cure and is best used for: • Tile • Rubber • Wood • Metal • Masonite • Particle Board • Plywood • Leather • Formica • Plastic • Laminates PROPERTIES: Initial Color: Amber Dry Time: 30 minutes Final Color: Amber Full Strength: 24 hours Open Time: 10 minutes Operating Temperature Range: 15° to 150°F -9° to 66°C Instructions: Use in a well-ventilated area. 1. Surfaces should be clean and dry. For best results, use fine sandpaper to roughen the surface. 2. Apply Contact Cement to both surfaces and wait 10 minutes. 3. Press parts together. Clamp heavier parts together. Allow 30 minutes for drying time. 4. For optimum strength in all applications, wait 24 hours before using the repaired object. 5. Clean off tube or bottle top and tightly cap adhesive. Store upright and away from heat sources. Note: Solvents may evaporate from bottle or tube if left open for prolonged periods. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains methyl ethyl ketone, hexane and ethyl acetate. Warning – liquid adhesive is extremely flammable. Harmful or fatal if swallowed. Injurious to eyes with direct contact. Avoid prolonged breathing of vapours and prolonged skin contact. Wear suitable protective clothing and gloves. Use and store in a well-ventilated area away from heat, sparks or flame. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $7.95

  • Tarzan's Grip Super Glue The King Of Strenght Sets in Seconds 2ml Tarzan's Grip Super Glue The King Of Strenght Sets in Seconds 2ml

    Tarzan's Grip Tarzan's Grip Super Glue The King Of Strenght Sets in Seconds 2ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Tarzan’s Grip Super Glue is a fast-setting cyanoacrylic acid ester based adhesive. Tarzan's Grip Super Glue dries colourless. Special multi-purpose formula allows product to bond to a variety of surfaces Quick-setting Dries clear, therefore no mess

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $6.06

  • Tarzan's Grip Shockproof Super Glue High Temperature Resistant 20g

    Tarzan's Grip Tarzan's Grip Shockproof Super Glue High Temperature Resistant 20g

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Tarzan's Grip Shockproof Super Glue is a high strength, rubber toughened adhesive that dries clear for a multitude of applications. In addition to offering a superior bond on metals, it is ideal for use with wood, rubber, leather, china, paper and most plastics. It resists extreme temperatures of up to 150C. Sets in around 2 to 3 minutes Impact resistant Heat resistant Superior bond on metals

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $10.44

  • Tarzan's Grip High Strength Glue Bottle 250ml

    Tarzan's Grip Tarzan's Grip High Strength Glue Bottle 250ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance.  Incredible bond strength Waterproof Superior strength Adheres to even visibly damp surfaces Longer work time (10 minutes)

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $23.70

  • SikaBond F40 SuperGlue for absorbent substrates with brush precise applicator 5g SikaBond F40 SuperGlue for absorbent substrates with brush precise applicator 5g

    Sika SikaBond F40 SuperGlue for absorbent substrates with brush precise applicator 5g

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Instant set, low viscosity, multipurpose super glue Suitable for bonding substrates with very smooth surfaces Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals Controlled dosage applicator nozzle Use: As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, leather, wood and other materials. It is especially suitable for bonding pieces with very smooth surfaces. Small repairs to glasses, shoe soles, picture frames, ceramics, toys and small electronic equipment, etc. Characteristics and advantages: One Component Easy to apply, low viscosity Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, leather Low consumption adhesive Versatile allows adhesion between different materials Colourless Durable COLOUR Clear Storage 12 months from date of production if stored in unopened and undamaged, original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +5ºC and +25ºC. Refrigeration to +5ºC gives optimum storage stability. 

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $28.00

  • SikaBond F100 Superglue with Anticlog Cap 3g SikaBond F100 Superglue with Anticlog Cap 3g

    Sika SikaBond F100 Superglue with Anticlog Cap 3g

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Medium viscosity, ethyl cyanoacrylate based instant setting adhesive where very fast cure speed is required.  Features: -Instant set, medium viscosity, multipurpose super glue -Suitable for bonding substrates with smooth surfaces -Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals -Controlled dosage applicator nozzle Use: -As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, leather, wood, paper and other materials. It is especially suitable for bonding pieces with very smooth surfaces. -Small repairs to glasses, shoe soles, picture frames, ceramics, toys and small electronic equipment, etc. Characteristics and Advantages -One Component -Easy to apply, middle viscosity -Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, paper -Low consumption adhesive -Versatile allows adhesion between different materials -Colourless -Durable   Colour: Clear Shelf-Life: 12 months from the date of production if stored in unopened and undamaged, original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +5°C and +25°C. Refrigeration to +5°C gives optimum storage stability. 

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $12.00

  • Last stock! Sikabond F Gel Superglue Non Drip for porous substrates with Anti clog cap 3g

    Sika Sikabond F Gel Superglue Non Drip for porous substrates with Anti clog cap 3g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Instant set, high viscosity, multipurpose super glue Suitable for bonding substrates with irregular surfaces and in vertical applications Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals Controlled dosage applicator nozzle Use: As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, fabrics, wood, paper and other materials Can be used on porous substrates such as porcelain and china Small repairs to glasses, bonded shoe soles, picture frames, ceramics, toys and small electronic equipment, etc. Surfaces with small irregularities max. 0.5 mm On vertical surfaces Characteristics and Advantages One Component Easy to apply, non-sag, gel consistency Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, paper, card Low consumption adhesive Versatile, allows adhesion between different materials Colourless Durable Packaging 3 g Tube

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $12.00

  • Selleys Water Shield Silicone Water repellent for Clothes, shoes, camping

    Selleys Selleys Water Shield Silicone Water repellent for Clothes, shoes, camping

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Introducing Selleys Water Shield, your go-to solution for making your fabrics water, snow, and ice-repellent without compromising comfort and breathability. Ideal for active individuals and outdoor enthusiasts, this product is designed to keep you dry while ensuring maximum comfort. Key Features Water, Snow, and Ice Repellent: Provides an effective barrier against moisture and cold elements. Breathable: Does not impair the comfort and breathability of the material, making it ideal for sportswear. Where to Use Sportswear, such as ski parkas, gloves, etc. Athletic shoes, including sandshoes and jogging shoes. Camping gear, like tents and sleeping bags. Cloth and canvas bags. Umbrellas. Outdoor furniture, e.g., canvas chairs. Paper maps and plans. Suitable for the Following Materials: Fabric Canvas Nylon How to Use Preparation: Ensure that the item to be treated is clean and dry. Application: Hold the aerosol can upright, approximately 100-150mm (4-6 inches) away from the surface. Spray: Use a sweeping motion to spray until the surface is moist. Dry: Allow approximately 3 hours for drying before using the item. Limitations Not suitable for leather or suede articles. Avoid use on fabric already treated with water repellents like DRW or waterproof materials like Gore-tex® or Driza-bone®. Do not apply to areas that don't require protection (e.g., soles of shoes). Handy Tips Test for colorfastness in an inconspicuous area before full application. Start spraying light-colored areas first, followed by darker areas. Launder or dry-clean soiled articles as usual and reapply the Water Shield. Specifications Size: 200g Aerosol Can Color: Colourless Technology: Silicone-Based Use: Suitable for both interior and exterior applications Keep your gear and clothing dry and comfortable. Experience the protection and convenience of Selleys Water Shield today!

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $21.00

  • Selleys Urethane Bond Weather and shock proof - Fix Garden Tools, Car Covers, Sports Equipment 30ml Selleys Urethane Bond Weather and shock proof - Fix Garden Tools, Car Covers, Sports Equipment 30ml

    Selleys Selleys Urethane Bond Weather and shock proof - Fix Garden Tools, Car Covers, Sports Equipment 30ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Urethane Bond Is a high strength shock proof, water and chemical resistant polyurethane adhesive. Features High strength Achieves maximum bond in 48 hours Shockproof Flexible, shatterproof and impact resistant so it can take knocks Durable Lasts a long time Chemical resistant Wont break down by temporary exposure to most chemicals i.e. solvents Waterproof and weatherproof Good for bonds exposed to the elements When curing, Urethane Bond expands, filling voids and strengthening the bond Easy to use Requires no mixing, ready to use straight from the pack Only need to apply adhesive to one surface Versatile Can be used inside or outside Sandable and paintable after dries

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $25.00

  • Selleys SoleGrip Anti Slip Adds Grip to Shoes Soles 85g

    Selleys Selleys SoleGrip Anti Slip Adds Grip to Shoes Soles 85g

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sole Grip is an easy-to-apply compound to repair and protect most shoe soles. Use it to coat the soles of shoes and protect from general wear and tear, extending the life of your shoes. Features: Easy to use Long wearing May be applied to both new and old shoe soles, as a repair or non-slip surface Appearance Dark brown tacky paste. Where can this product be used? Apply to new shoes to extend their sole life Building up worn soles of shoes to extend their life Creating an anti-slip surface on smooth soles of shoes Creating an anti-slip surface on the bottom of furniture legs and castor holders Creating an anti-slip base on fabric items such as dollies or placemats Sole Fix is not an adhesive May not adhere to some plastic/rubber soles Will not bridge gaps where no backing exists What materials is this product suitable for? Leather Rubber Synthetic Plastic How to use this product Roughen soles with the scraper provided. Clean the surface with Selleys Solvent Acetone. Do not use Turpentine or Kerosene. (Note: Slow drying solvents such as Mineral Turps may interfere with adhesion). Squeeze sufficient material for a thin layer about 1.5mm thick. Spread evenly over sole Leave for 30 minutes before further applications. If required, apply 2 or 3 layers on average soles. On worn soles apply to suit. Leave for 24 hours before wearing. Edges may be sandpapered or cut back and trimmed with a knife. Handy tips For best results, new shoes should be worn for several days before applying SoleGrip Clean up excess with Mineral Turpentine prior to cure Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Avoid skin contact and avoid breathing vapours.  If eye contact occurs, flush eyes with water for 15 minutes. Obtain medical attention. If skin contact occurs, remove contaminated clothing and wash skin thoroughly with soap and water. If swallowed, DO NOT induce vomiting. Give a glass of water and seek medical advice. Intentional misuse by deliberately inhaling vapours of this product can be harmful or fatal.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $18.69

  • Selleys Shoefix Repair Clear Adhesive Flexible Bond 50ml

    Selleys Selleys Shoefix Repair Clear Adhesive Flexible Bond 50ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A strong, weather and impact resistant adhesive that is ideal for most shoe repairs. Features Easy to use Strong Flexible Bond Weather resistant Impact resistant Appearance Dries yellowish/beige Where can this product be used? Sole Tongue Strap Inner sole Attach beads, jewels, decorative items Will not bond Polyethylene or Polypropylene plastics. For these we recommend Selleys Plastics Glue. May not adhere to some plastic / rubber soles. What materials is this product suitable for? Leather Canvas Fabric Rubber Cork Most Plastics EVA foam (e.g Desert boots sole) How to use this product Ensure surfaces are clean, dry and free from dirt or grease. Remove cap and carefully pierce seal. For larger area repairs such as shoe soles, we recommend you use the contact bond method: For quick and even bonding, apply to one surface only, press together and pull apart. Keep apart until the adhesive film is almost dry (approx. 10 – 20 minutes). Carefully line up surfaces to be joined and press surfaces firmly together. Bonds immediately on contact. Clamping may be necessary in some applications. For smaller areas, either use the contact method as above, or join with a wet bond: Apply Shoe Glue to one surface only and immediately press together. Lightly clamp or hold until dry. Allow adhesive to achieve maximum bond strength (24 hours) before wearing your repaired shoe/s. Wipe nozzle clean and replace cap immediately after use. Clean up application tools and excess adhesive with turps before it dries. Handy tips A piece of plastic from a takeaway container makes a good applicator for shoe soles. Bulldog clips are handy to use for clamping straps and other small areas. Pack includes a removable nozzle for easy application.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $6.00


You have seen 48 out of 124 products

Works on: Leather

Find products tagged for use on leather. This collection includes adhesives, sealants, tapes and accessories chosen for typical repairs and installs on leather surfaces. Compare cure speed, flexibility, clarity and temperature ratings to match your project. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.

Login

Forgot your password?

Don't have an account yet?
Create account