PC-11® thrives in wet environments. It is resistant to water whether it is fresh or salt. Thick consistency like PC-7® and long open time (30 min). Work horizontal or vertical, indoor or outdoor. Wet, dry or under water. Whether you are working on an area where you just can’t remove water and moisture or you want the white colour for your repair, PC-11® is your choice. Choose PC-11® for ceramic repairs, pools and spas, fibreglass boats, tubs and sinks, stock tanks and thousands of other repairs. It has excellent adhesive properties bonding metals, fibreglass, wood, tile and some plastics such as ABS and rigid PVC. Ample open time allows tooling or positioning in order to tackle larger and challenging jobs. When mixed, the epoxy, part A (white) and the hardener part B (lt. blue) react to form a bond of tremendous strength and flexibility. The PC-11® formulation is slow curing, but slow can be a good thing especially for large tasks. WORKING TIME: 30 MINUTES CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE) PC-11® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Not quite as thick as peanut butter. Here are just a few specific uses (there are hundreds of other uses): Reattach missing swimming pool tiles. Patch a hole in a fibreglass canoe or the fibreglass keel of a fishing boat. Repair cracked or damage swimming pool or hot tub skimmer. Waterproof and Seal cracked fibreglass. Seal screw holes to hatch lids or seating. Attach fish locators to transom. Repair stock tanks. Repair broken refrigerator door shelf fixtures. Repair broken pottery. Repair shower basin or antique bath tub. Seal leaking air conditioner drip pan. Seal underground conduit. How to prepare a surface for bonding with PC-11® Epoxy Paste Remove contaminants such as dust, dirt, oil, barnacles and grime with a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. For a wet or underwater surface; clean contaminants as best as you can. Solvents will not help you in this situation. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-11® Epoxy Paste application Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-11® cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. Can PC-11® be used in Aquariums? There is the potential for PC-11® part A and part B to harm sea life but properly measured and mixed PC-11® has been used safely in fresh and saltwater aquariums. It is important that part A and B are thoroughly and completely mixed. What plastics does PC-11® stick to? PC-11® has good adhesion to Rigid PVC and CPVC, polyester and fiberglass, polyurethane, ABS and Bakelite. What plastics does PC-11® not stick to? PC-11® does not stick to polyethylene, polypropylene, HDPE, polystyrene, nylon, acrylic, Teflon, and polycarbonate. What rubbers does PC-11® stick to? PC-11® sticks to SBR, Buna, and polyurethane rubbers and does not stick to EPDM, vinyl and neoprene rubbers. What temperatures can PC-11® be applied? PC-11® cures very slowly at temperatures below 50°F (10°C). At or below freezing temperatures the PC-11® will stop curing. In hot conditions, above 95°F (35°C), PC-11® will cure rapidly reducing the working or application time. Can gel coat be applied to PC-11®? Gel coat will not cure properly in direct contact with PC-11®. It is important that repairs made with PC-11® be sealed with a suitable primer/sealer before applying a gel coat. Can PC-11® be painted? Yes. It is good practice to apply a premium stain sealing primer to repairs made with PC-11® prior to the finish coat. Will PC-11® yellow in direct sunlight? Yes, PC-11® yellows in direct sunlight. PC-11® resists ultraviolet light but will still gradually change colour. Prime and paint if the colour is important. Can PC-11® be thinned with solvent? PC-11® does not contain solvents. Acetone and denatured alcohol (ethanol) are compatible but will extend the cure time and decrease the hardness. Other solvents such as mineral spirits, paint thinner and turpentine are not compatible. PC-11® is a simple one to one mix, but how accurately does the measurement need to be? The volume of part A to part B should be close to equal. A slight excess of part A is preferable to an excess of part B. Excess of part B will not accelerate the curing and it may make it softer.
$21.95
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$7.50
Glitz Caustic Soda for Drains and Heavy Duty Cleaning 500g Cut through the toughest grime with Glitz Caustic Soda. These high strength crystals are ideal for clearing slow or blocked drains and tackling heavy duty cleaning tasks in workshops, garages, and outdoor areas. Designed for fast action on built up fats, oils, soap scum, and organic matter, it is a must have for serious cleaning jobs. Key benefits Unblocks and deodorises kitchen, bathroom, and laundry drains Heavy duty degreasing power for floors, bins, and exterior concrete Crystalline form for controlled use and minimal waste Effective on fats, oils, grease, and soap build up Convenient 500 g jar suitable for home and trade users Where it works Kitchen sinks and traps Bathroom basins, showers, and laundry tubs Outdoor drains and gullies Greasy hard surfaces like concrete and pavers What to know before you start Always wear chemical resistant gloves, eye protection, and long sleeves Use in a well ventilated area and avoid breathing dust Do not mix with acids, bleach, or other chemicals Add crystals to water, never water to crystals Not suitable for aluminium, zinc, tin, or painted and delicate surfaces How to use Remove as much standing water and debris as possible from the drain or surface. Carefully dissolve the required amount of crystals in cold water. Stir gently until dissolved. Pour the solution slowly into the drain or apply to the surface. Avoid splashing. Allow time to work, then flush drains thoroughly with plenty of water or rinse surfaces well. Repeat if necessary for heavy build up, following all safety directions. Good practice tips For maintenance, treat problem drains periodically to prevent build up Keep children and pets away from the work area until rinsed and dry Store tightly closed in a cool, dry place away from moisture Product details Brand Glitz Product Caustic Soda Chemistry Sodium hydroxide Form Crystals Size 500 g Suitable for Drains, heavy duty degreasing on hard, non reactive surfaces Not for use on Aluminium, zinc, tin, painted surfaces, natural stone, fiberglass, anodised finishes Safety and first aid Corrosive. Avoid contact with skin and eyes. Do not ingest. In case of contact, flush with water for at least 15 minutes and remove contaminated clothing. Refer to the Safety Data Sheet (SDS) for full details. Frequently asked questions Will it damage my pipes Glitz Caustic Soda is suitable for most household drains when used as directed. Avoid use on systems with aluminium components and always flush thoroughly. Is it safe for septic systems Generally suitable when used as directed and in moderation. Avoid repeated heavy dosing. If unsure, consult a licensed plumber. Can I use it on painted or decorative surfaces No. It can strip or dull finishes. Use only on compatible, non reactive hard surfaces. You may also need Heavy duty chemical resistant gloves Protective eyewear Plastic drain auger for physical blockage removal Always follow the directions on the packaging. Test on a small, inconspicuous area for surface compatibility.
$6.16 $5.00
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$9.70
Selleys Spakfilla Rapid is a ready-mixed, lightweight filler designed for fast and easy repairs. It dries quickly, resists cracking and shrinking, and usually requires only one application—making it ideal for quick patching jobs around the home or office. Features Fills cracks and holes in a single application Pre-mixed and ready to use straight from the tub Minimal shrinkage – no need to overfill Fast drying – sand and paint within a short time Includes a convenient filling spatula Water-based formula – easy clean-up with water Paintable with both oil-based and water-based paints Where to Use Cracks and holes on stable, non-moving surfaces Walls, ceilings, doors, and window frames Small repairs in plaster, timber, and masonry surfaces Suitable Materials Wallboard and plasterboard Wood and timber surfaces Masonry and plaster Primed nail heads Product Details Colour: White Technology: Water-based Use: Interior, or exterior when painted How to Use Ensure surfaces are clean, dry, and free of dust or loose material. Using the provided spatula, press filler firmly into the crack or hole and smooth the surface. No need to overfill. Allow to dry (approximately 30 minutes for thin applications), then lightly sand for a smooth finish. Remove dust and paint as desired. For oil-based paints, allow 24 hours before painting. Limitations Not suitable for use on plastic, metal, or exterior timber exposed to moisture. Not flexible – avoid using between surfaces subject to structural movement (use Selleys No More Gaps Coloured Caulk 450g instead). Not designed for load-bearing areas or surfaces under compression (e.g. behind doors). Do not nail through filler. Avoid use below 5°C or in wet conditions. Handy Tips Wait 24 hours before painting with oil-based paints. Water-based paints can be applied once the filler has set. If filler thickens, stir before use. If too dry, add a small amount of water and mix. Clean tools with water after use. Before painting, clean with Selleys Sugar Soap Cleaner Concentrate 1L or Selleys Sugar Soap Wipes x25. For outdoor applications, protect from rain until dry and painted with two coats. Deeper repairs (over 2mm) may require longer drying times. Recommended Accessories For masking before painting: Bear Masking Tape Painter Edge Pro 48mm x 50m For reinforcing plaster joints: Eazy Tape Plasterboard Joint Tape 90m Clean Up Remove uncured product with water. Once cured, remove by scraping or sanding.
$15.56
Tarzan’s Grip Multi-Purpose General Adhesive 250 g is a reliable versatile contact style adhesive for crafts and household fixes chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 250 g pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Tarzan's Grip Grip for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Multi-Purpose General Adhesive 250 g has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bonding fabric, leather, and rubber General craft builds Light repairs around the home Suitable surfaces The adhesive works well on the following surface types when properly prepared: Leather and canvas Rubber trim Timber and some plastics Card and foam board Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of allow adhesive to tack before assembly as directed on pack. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Forms a tough, flexible bond after solvent evaporation and cure. Press parts together firmly for best adhesion. Temperature and environmental performance Keep away from flames and high heat during application. Once cured, it resists typical temperatures. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Use appropriate solvent on uncured adhesive, working in a ventilated space. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Replace cap after each use to reduce skinning. Store below 30 C. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$15.59
Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result. Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco Ideal for over-head applications (non-slump formula) Excellent adhesion to all cementitious surfaces Suitable for interior and exterior applications Not suitable for use on damp surfaces Tools Needed: Filling Knife Properties: Ready to use Will not shrink or sag Easy to sand Accepts nails and screws Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint Sandable after 24 hours Accepts oil-based paints after 48 hours Maximum layer thickness: 5 cm Maximum depth: 10 cm Colour: Light Grey How to Apply: Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix well before use. Product can be used directly from the pot. Apply the product firmly in to the hole with a filling knife. For a super smooth result, finish with a damp filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. Replace cover sheet after use and ensure lid is properly closed. Once dry sand to a smooth nish. Clean tools with warm water immediately after use. Do not store or use under 5°C.
$22.66
Davco® Sanitized Tile & Grout Sealer is a solvent-based sealer that provides excellent protection against stains, soiling, discolouration, and efflorescence. It’s an easy-to-apply, clear solution that cures to form an invisible, water-repellent coating. Key Benefits: Clear solution that cures to an invisible, water-repellent coating Easy to apply Usage: Surfaces: Only suitable for cement-based grouts Can be applied over most unglazed porous ceramic tiles Areas: Suitable for both interior and exterior applications Ideal for commercial and domestic wall and floor grout joints Advantages: Protects against stains, soiling, and discolouration Provides an invisible protective layer that repels water Perfect for enhancing the durability of grout in high-traffic areas
$20.98
Selleys Spakfilla Rapid is a ready-mixed lightweight filler that is fast drying, virtually non-shrinking, non-cracking & needs only one application. Features Fill cracks and holes in a single application Pre-mixed and ready to use Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water-based, so can be cleaned up with water Paintable with oil and water-based paints Where can this product be used? Filling cracks and holes on surfaces where no structural movement occurs Filling cracks in walls, ceilings, doors, windows Repairing holes in walls, ceilings, doors and windows What materials is this product suitable for? Wallboard Wood Masonry Plaster Primed nail heads Plasterboard Colours White Technology Water Based Use Interior Exterior (when painted) How To Use Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. Lightly sand back any excess filler from the surface after product dries (30 minutes in thin applications). Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting. Limitations: Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water. Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall. Nailing this product is not recommended. Avoid using below 5°C or in wet conditions. Handy Tips Painting with oil-based paints is not recommended until 24 hours after filler has been applied. Water based paints may be used immediately after filler has set. If filler is found to have stiffened prior to use, stir product. Product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency. Application tools may be cleaned with water. Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen. In exterior applications, protect from rain until dry and painted over with 2 coats of paint. Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry. For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times. Keep container closed when not in use. Clean Up Uncured product may be removed with water. Cured product can be removed by scraping or sanding.
$25.02
Polishes internal furniture & joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items. Also suitable for sealing and polishing slate, terracotta and stucco Coverage: Up to 40 m2 Number of Coats: 2 Recoat: 24hrs Sheen Level: Pale Satin
$15.95
A high grade linseed oil putty with excellent adhesion for repairing and glazing wood and metal frames. For use on: Wood & metal (EXTERIOR & INTERIOR) Dries in: Skins over in 2-3 days depending on weather conditions. Ready to use: YES Colour: Light brown Ensure all surfaces are clean, sound and dry. Remove all old putty, dust off loose and crumbling material. • Bare timber should be primed with an oil-based primer before applying putty. • Knead putty thoroughly for smooth, even consistency in application. • Apply putty to working area with either a thumb or putty knife. When evenly applied, smooth off. • Always allow several days for putty to skin before applying an oil-based undercoat. Can be painted with either water or oil-based topcoat. Q. I used Polyfilla Putty on a window frame and have noticed some wrinkling on the surface. Is something wrong with the product? A. No. When this product is used on metal window frames exposed to heat, some surface wrinkling can occur. This will not affect the performance of the putty in any way.
$13.53
A vinyl reinforced cement-based filler that is water and weather resistant. Matches cement grey when set and easily sands whilst maintaining the strength of cement. Can be nailed and screwed without splitting or breaking. Will not shrink when used in accordance with directions, making it suitable for use in patching steps, paths, paving etc. For use on: Bricks, cement, stone and other masonry surfaces (EXTERIOR). May be used in interior wet areas and as ceramic floor tile cement. Fill depth: Dependent on mix ratio Dries in: 5-6 hours for sanding. Allow 24 hours before painting. Ready to use: NO (mix with water) Available in: 500g & 2kg Colour: Grey and can be tinted by adding cement colorants to the mixing water. Application tips: • Surface to be filled should be clean and dry with no loose or powdery material. Do not wet or prime surfaces before filling. • Coat nail heads with oil based paint prior to filling to prevent rust staining. • Add 4 parts Polyfilla Exterior Powder Filler to 1 part water in a clean container and mix thoroughly into a smooth paste. Use mix within 30 minutes and do not add water to extend working time. • For deeper cracks and holes and on very absorbent surfaces it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Press in the mixed filler with a filling knife or trowel and finish with a slightly rounded surface. Where a smooth surface is required, slightly overfill the surface, allow to dry (approx. 5-6 hours), then sand smooth with medium grade sandpaper. • Leave for 24 hours, and then apply a suitable primer/undercoat before painting. • When applying in thin layers, do not over trowel. • Clean up with water before filler dries
$21.60
Parfix Fast Grip is a solvent-based contact adhesive that is heat and water-resistant, making it suitable for use in kitchens and bathrooms. Immediate strong bond Heat and water resistant Brush application
$21.22
Give everyday cleaning a simple, natural boost with Glitz Bi-Carb Cleaner. This all purpose powder uses the gentle abrasive action and deodorising properties of sodium bicarbonate to lift grime, cut through kitchen film, and freshen household surfaces without added fragrances or dyes. Why you will love it Versatile cleaner for kitchens, bathrooms, laundry, and outdoor touch ups Deodorises fridges, bins, shoes, and pet areas Gentle abrasive action helps remove tea stains, soap scum, and cooked on residue Eco minded choice with a simple, trusted mineral based formula Food area friendly when used as directed, then rinsed well Value size 1kg pack is ideal for regular household cleaning Where to use Benchtops, sinks, stovetops, splashbacks Microwaves, fridges, lunch boxes, drinkware Showers, tiles, grout, basins Bins, pet bowls, outdoor furniture Laundry pre soak for odours in sportswear and towels Car interiors and coolers How to use General cleaning: Sprinkle a small amount onto a damp cloth or sponge. Wipe the surface, then rinse and dry. Stubborn marks: Make a paste with a little water. Apply to the stain, leave for 5 to 10 minutes, then scrub lightly and rinse. Deodorising: Sprinkle directly onto the source of odour, leave for 15 minutes, then vacuum or rinse away. Drains and sinks: Add half a cup followed by hot water to help freshen and reduce build up. Good to know Non scratch on most hard surfaces when used with a soft cloth No added fragrance or dyes Septic safe when used as directed Ingredients Sodium Bicarbonate. Care and safety Test on an inconspicuous area first, especially on delicate finishes and natural stone. Do not use on aluminium, lacquered or highly polished surfaces. Avoid contact with eyes. Keep out of reach of children and pets. Store tightly closed in a cool, dry place. Pack information Brand Glitz Product Bi-Carb Cleaner Natural Eco All Purpose Powder Net weight 1kg Format Fine cleaning powder Country of use Australia Simple tips Refresh chopping boards by applying a paste, scrubbing lightly, then rinsing with warm water. Neutralise fridge odours by placing an open dish in the fridge and replacing monthly. Lift tea and coffee stains in mugs by soaking with a warm water paste for 20 minutes before washing. What customers ask Is it safe on stainless steelYes, use a soft cloth, rub with the grain, then rinse and dry. Can it be used on natural stoneTest first. Rinse thoroughly and dry to protect sealed finishes.
$12.40 $11.03
Dulux Precision Maximum Strength Adhesion Primer Get a tough, reliable bond on hard to paint surfaces with Dulux Precision Maximum Strength Adhesion Primer. This water based, low odour primer works as a primer, sealer and undercoat, creating a strong foundation for acrylic or oil based topcoats on both interior and exterior projects. Why choose this primer Water based with low odour Excellent adhesion on glossy and hard to coat surfaces Suitable as primer, sealer and undercoat Interior and exterior use Fast drying: touch dry in 30 minutes, recoat in 1 to 2 hours Topcoat within 30 days for best results Ideal surfaces Tiles, high gloss enamels, varnished timber, uPVC, fiberglass, aluminium, galvanised steel, Colorbond, glass, glazed brick, laminates and previously painted glossy finishes. Key specs Finish Flat Colour White Coverage Up to 10 m² per litre per coat, depending on surface Dry time Touch dry 30 minutes Recoat time 1 to 2 hours Full strength 7 days after application VOC 30.4 g/L Application temperature Between 10°C and 32°C Clean up Water Pack sizes 1 L and 4 L How to use Prepare the surface so it is clean, dry and free of grease, wax, dust, loose paint and rust. Wash if needed and allow to dry. Stir thoroughly before and during use. Apply 1 even coat with a high quality brush, roller or spray. For very smooth surfaces 1 coat is usually sufficient. Allow 1 to 2 hours before recoating or applying the topcoat. Topcoat within 30 days. Application tips Do not tint for difficult surfaces. Thin only if necessary with a small amount of water. When using solvent based enamel topcoats, lightly sand the primer before applying the enamel. If using under products with strong solvents, let the primer dry 24 hours and test compatibility on a small area first. Where not to use Floors, benchtops or surfaces subject to standing water Below 10°C surface temperature or if conditions may drop below 10°C during drying Clean up and safety Clean tools with water and a mild detergent, then rinse. Ensure good ventilation during use. Wear eye protection and avoid skin and eye contact. Always follow label directions.
$49.88
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour. Features Easy to use. Can be applied by hand or with a putty knife Product has exceptional keeping qualities Available in a natural colour Superior grade putty Where can this putty be used? A wood sash putty that is excellent for glazing wooden windows and doors Bedding glass beads Not recommended for use with heat absorbing glass If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes Not recommended for use where structural movement may occur Not recommended for use in metal framed windows. What materials is this putty suitable for? Wood Timber How to use this product Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing. Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used. Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass. Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing. Paint should be carried out 2mm above the top line of the putty. Handy tips Do not use kerosene, turps or other material to aid in working the putty Allow putty to skin before applying paint Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it. Putty must be painted in exterior applications. High humidity, cold weather and use in interior applications can extend skinning times. Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil. Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen. Safety tips Low hazard material For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
$41.00
Selleys Spakfilla Heavy Duty is a multi-purpose, tough and durable, light grey ready-mixed filler. Features Suitable for interior and exterior applications Good adhesions to most surfaces Water and weather resistant Fill cracks and holes in a single application Pre-mixed and ready to use Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water-based, so can be cleaned up with water Paintable with oil and water-based paints Where can this product be used? Filling holes, dents, cracks or chips in interior and exterior applications where no structural movement occurs What materials is this product suitable for? Mortar Masonry Concrete Wood Stone Primed metal surfaces Brick Plaster Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. For deeper cracks, apply in 6mm layers allowing each layer to dry before applying the next. Lightly sand back any excess filler from the surface after product dries (2-3 hours for 2mm applications). Dust off any loose dust before applying undercoat and painting with water-based paints or oil-based paints. Limitations: Product is not flexible so not suitable for use between surfaces that are subject to the structural movement - use Selleys No More Gaps. Avoid using below 5°C or in wet conditions. Painting with oil-based paints is not recommended until 24 hours after the filler has been applied. Water-based paints may be used immediately after the filler has set. If the filler is found to have stiffened prior to use, stir product. The product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency. Application tools may be cleaned with water. Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen. In exterior applications, protect from rain until dry and painted over with 2 coats of paint. Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry. For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times. Keep container closed when not in use.
$22.66
Selleys N Mastic is a non-hardening, waterproof sealing putty designed for a wide range of applications where long-lasting flexibility is crucial. Ideal for sealing joints, gaps around windows, and roofing, it ensures that structures remain protected from water ingress. The unique formula remains pliable, making it perfect for environments where movement and expansion are expected. Whether you're sealing an outdoor roof gutter, securing window frames, or filling gaps in an air conditioning system, Selleys N Mastic provides a professional-grade finish with no cracking or crumbling. The product is also suitable for metal, glass, concrete, and brick, making it a versatile solution for residential, commercial, and industrial projects. N-Mastic is a non-skinning polybutene-based compound. It will remain permanently soft and paste-like. Uses N-Mastic is suitable for sealing concealed lap joints between plastics, metals, timber, glass, masonry, and expanded foam panels. It may be used in the installation of cool rooms, prefabricated construction and gasket sealed windscreens to exclude draughts and water penetration through joints in materials. Technical Features Non-hardening – remains permanently flexible to provide a lasting seal Good adhesion – adheres well to most substrates Moisture resistance – provides an excellent barrier to moisture vapour Microbe resistance – resists microbial attack Low shrinkage – avoids the risk of sealant pulling away from joint surfaces Wide service temperatures – withstands –40oC to +80oC service conditions Application Tips Due to the non-skinning, non-hardening nature of the sealant, N-Mastic should not be used in exposed joints where dirt pick-up or hand contact can be a problem. As N-Mastic is not elastomeric, it should not be used in areas subject to considerable dynamic stress. Although N-Mastic is resistant to static pressures, a curing sealant is recommended where this is a critical factor. N-Mastic is not recommended for sealing lap joints in mobile homes, truck bodies, etc., as significant vibration and flexing occur during travel. Technical Details and Performance Indicative information only, not to be used for setting specifications. Colour Off White Specific Gravity 1.4g/mL Consistency Non-sag Slump (MIL-S-8802, @ 32oC ) 2.5mm maximum Viscosity (Brookfield HAF 7/2 @ 25oC ) 10,000 – 14,000 Poise Flash Point 85oC Storage Life (25oC ) Indefinite Packaging Plastic cartridge (410g) Performance Properties Shrinkage (% maximum) 5 Service Temperature –40oC to +80oC Life Expectancy Up to 20 years Clean Up Sealant may be removed with a cloth dampened with kerosene or mineral spirits
$19.11
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$4.43
Polishes internal furniture & joinery that has been previously waxed or oiled Suitable for Timber, concrete, slate, terracotta and stucco All-natural ingredients Apply with a lint-free cloth Polishes internal furniture and joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items. Uses: Also suitable for sealing and polishing slate, terracotta and stucco Coverage: Up to 40m² Apply with: Lint-free cloth Number of coats: 2 Sheen level: Pale Satin
$32.95
A blend of nut and citrus oils specially formulated to create a drying oil to maintain and rejuvenate wooden items that come into regular contact with food or water which can cause the timber to swell and dry out. Simple wipe on and wipe off application to make timber look & feel nourished. Maintain wood items that come in contact with food & water. Ideal for wooden chopping boards, serving bowls and utensils. 250mL Simple wipe on and wipe off with a rag
$16.88
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink. For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR) Fill depth: Dependent on mix ratio Dries in: 2-3 hours Ready to use: NO (mix with water) Available in: 500g, 1kg, 2kg & 6kg Colour: Off-white • Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key. • Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate. • Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge. • Leave for 2-3 hours before sanding and decorating. • For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area. • Clean up with water before filler dries
$46.15
Feast Watson Outdoor Furniture Oil in Clear is a penetrating timber oil made to protect outdoor furniture while keeping the natural look of the wood, supplied here in a 1L can. It soaks into the surface rather than sitting on top, so it leaves a natural matt finish that lets the grain and texture show through.About the formulaAn oil-based, one-component formula enriched with eucalyptus oil. It is designed to resist mould and to give excellent water resistance, and the film is penetrating, so it is not expected to crack or flake. The Clear colour keeps the timber's own tone. It is not recommended for direct sunlight or extreme conditions. If you want a higher level of UV protection, choose one of the tinted colours in the range (Hardwood, Jarrah, Teak or Weathered Grey).Where to use itIndoors: not the intended use, as this oil is made for outdoor timber.Outdoors: timber outdoor furniture such as chairs, tables and benches, plus timber BBQ trolleys.Suitable for exterior timber furniture. Test a small, hidden area first if you are unsure how your timber will look.How to use itClean the furniture first with Feast Watson Woodclean to remove dirt, oil, wax and grease, then let it dry fully. Stir the oil thoroughly before and during use so the colour stays even. If you need more than one can, combine them in a larger container first. Apply the first coat with a quality brush, working in sections along the grain and fully coating edges and end grain. A roller or applicator pad can also be used. Let the oil soak in, then wipe off any excess with a brush or clean cloth. Leave it for 12 hours before applying a second coat. For chairs and benches, start on the inside of the legs, then move up to the seat and finish with the back. Clean brushes and tools with mineral turpentine.Important notesAllow about 12 hours between coats. Touch dry time is around 6 hours at 25°C and 50% humidity, and cooler or more humid conditions will take longer. Do not apply below 10°C, in very hot weather, or when rain or heavy dew is expected while the coating dries. Two coats are recommended, and the manufacturer lists a spread rate of about 6m² per litre, which varies with the timber. Over time, watch for colour loss, dryness and weathering. When that happens, clean with Woodclean and apply one maintenance coat. Soak used rags and cloths in water before disposing of them.Specifications Brand Feast Watson Product Outdoor Furniture Oil Size 1L Colour Clear Base Oil-based, with eucalyptus oil Finish Matt Application Brush, roller or applicator pad Coats 2 Recoat time 12 hours Spread rate About 6m² per litre Minimum application temperature 10°C Clean up Mineral turpentine Use Exterior timber furniture, BBQ trolleys and benches SafetyUse in a well-ventilated area and keep away from heat, sparks and open flame. Avoid contact with skin and eyes, and wear gloves and safety glasses while working. Keep out of reach of children and store the sealed can in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$74.61
Sika Colma Cleaner is a grease-free, solvent-based cleaner made for wiping down bond faces before bonding or sealing, and for cleaning tools and equipment, supplied here as a 1L can. It is a quick, easy-to-use surface prep step that helps strip away oily and industrial residues so primers, activators, adhesives and sealants have a clean surface to work on.About the formulaA one-component, solvent-based liquid that is clear and very thin, so it wets a surface quickly and flashes off without leaving a greasy film. Sika designed it to lift traces of mould release oils and other industrial contaminants from non-porous surfaces. It can also be used to clean tools and equipment.Where to use itIndoors: workshop and factory pre-cleaning of metal bond faces, and cleaning down tools and application equipment, as long as there is good ventilation and no ignition sources.Outdoors: on-site pre-cleaning of metal substrates before applying primers, adhesives or sealants, in suitable weather (see temperature range below).Suitable materials include light metals and alloys, steel and stainless steel.How to use itSoak a clean rag or lint-free paper towel with the cleaner and wipe the bonding areas to remove surface contamination. Work with clean cloths so you lift the contamination off rather than spread it around. After a flash-off time of at least 15 minutes, apply the primer or activator specified for your bonding or sealing system, and allow the flash-off time for that product. Reseal the container tightly straight after each use. Use at ambient and substrate temperatures between +5 °C and +40 °C, and at least 3 °C above the dew point. Allow roughly 50 ml per square metre as a guide.Important notesDo not use on porous substrates. On painted, plastic or other sensitive surfaces, test a small hidden area first or choose a more suitable cleaner. The flash-off time is a minimum of 15 minutes and a maximum of 8 hours, so apply the next product within that window. Unopened product has a shelf life of 24 months from production when stored in the original sealed container, dry, out of direct sunlight, at +5 °C to +25 °C.Specifications Brand Sika Product Colma Cleaner Size 1L can Colour Transparent Base One-component, solvent-based cleaner Application Wipe on with a clean rag or lint-free paper towel Flash-off time Minimum 15 minutes, maximum 8 hours Consumption Approx. 50 ml/m² Density Approx. 0.85 kg/L Flash point Approx. 14 °C Application temperature +5 °C to +40 °C (air and substrate) Shelf life 24 months in sealed original packaging Use Pre-cleaning of non-porous bond faces, tools and equipment SafetyThis is a highly flammable solvent. Keep it away from heat, sparks, open flames and other ignition sources, and do not smoke while using it. Use only outdoors or in a well-ventilated area, avoid breathing vapours, and wear protective gloves, eye protection and suitable protective clothing. Take steps to prevent static discharge and keep the container tightly closed. Refer to the Safety Data Sheet (SDS) for full details.
$33.48
Turbo Metal Builders Bog is a two part, aluminium and glass fibre reinforced polyester filler for rusted metal, dents, cracks, holes and tears, supplied here as a 500ml can. It is aimed at panel beaters, builders and DIYers who want a hard, workable repair that can go over or under ordinary body filler for extra strength, and which also works on fibreglass, wood, stone, concrete and aluminium.About the formulaThe filler is a paste based on unsaturated polyester resin in styrene, loaded with aluminium so you can repair metal with a metal-filled compound, and with glass fibre strands that help bridge holes and gaps. Once catalysed with a separate peroxide-based hardener, the mix gels to a cheese-like consistency that can be cut, shaped or pared, then cures hard. Changing the amount of hardener lets you speed up or slow down the set to suit the job and the weather. Turbo describes it as having minimal shrinkage, good stress resistance and flexibility, water resistance and rust-inhibiting properties.Where to use itIndoors: repairing holes, cracks and damaged areas in fibreglass, wood, stone and concrete, and filling larger voids where a standard filler would sag or shrink.Outdoors: rusted-out panels, dents and holes in metal, vehicle bodywork and similar repairs, plus cracked or broken concrete, masonry and aluminium items exposed to weather.Suitable materials include steel and other metals, aluminium, fibreglass, wood, stone, concrete and masonry. It can be used instead of, or underneath, regular plastic body filler.How to use itStart with a clean, dry, sound surface, free of loose rust, paint, oil, grease and dust, and roughen smooth surfaces for a better key. Work out how much filler you need and mix it with the hardener following the directions on the can, stirring until the colour is completely uniform. Because cure speed depends on temperature and the amount of hardener, try a small batch first. Press the mix firmly into the repair, building up and shaping it while it is still soft. Once it has gelled you can trim it, then sand, file, drill, machine and paint it after it has cured hard.Important notesThis is a two part system and will not cure without the hardener, so check the hardener is on hand before you start. More hardener or warmer conditions will shorten the working time, and less hardener will lengthen it. Full cure is typically within about 30 to 60 minutes, and the repair can be painted within the hour, though times vary with temperature and mix. The cured filler is paintable but not stainable. For large structural repairs on metal, make sure the underlying area is sound.Specifications Brand Turbo Product Metal Builders Bog (metallised repairer) Size 500ml can Colour Grey Base Unsaturated polyester resin filler with aluminium and glass fibre Application Hand applied after mixing with hardener Set and cure Gels to a cheese-like consistency, full cure typically about 30 to 60 minutes (varies with hardener and temperature) Paintable Yes, within the hour Sandable Yes Stainable No Shrink resistant Yes UV resistant Yes Use Interior and exterior SafetyKeep away from heat, sparks, open flames and hot surfaces, and do not smoke. Use outdoors or in a well-ventilated area, avoid breathing vapours, and avoid contact with eyes, skin and clothing. Wear suitable gloves and eye protection. Wash exposed skin thoroughly after handling and remove contaminated clothing. Refer to the Safety Data Sheet (SDS) for full details.
$32.41
Parfix Foam Fill Triple Expanding Filler is a polyurethane foam in a 750g aerosol can, made for packing out large gaps, cracks and cavities in and around the home. It expands well beyond its sprayed volume to fill irregular voids, then cures to a durable, water resistant foam that bonds to most common building surfaces.About the formulaA one-part polyurethane foam based on an isocyanate (MDI) prepolymer, supplied in a pressurised can. Once cured it is a firm, shrink resistant foam that can be cut, sanded and painted. Cured foam is not UV resistant, so exposed outdoor areas should be painted or covered.Where to use itIndoors: gaps around pipes and cable penetrations, cracks and holes in walls, and cavities around frames and fittings.Outdoors: holes and gaps in brickwork and other building surfaces, protected from direct sunlight once cured.Suitable for most building surfaces, including timber, metal, brick, stone and other masonry. Test on a small hidden area first if you are unsure about a particular material.How to use itWear gloves and safety glasses and work in a well ventilated area. Make sure surfaces are clean and free of loose material, dust and grease. Follow the directions printed on the can for shaking, nozzle attachment and application. Because this foam expands strongly, fill the gap only partly and allow room for growth rather than over-filling. Once fully cured, trim any excess with a knife or saw, then sand or paint as required. Uncured foam is best wiped off straight away with a suitable cleaner as directed on the can. Cured foam must be cut or sanded off.Important notesNot UV resistant, so paint or coat any foam that will be exposed to sunlight. Take care not to over-fill, as expanding foam can distort thin frames, door jambs and window casings. Keep the can away from heat, flames and sources of ignition. Check the can label for temperature range, cure times and further directions, as these are not covered in the product data we hold.Specifications Brand Parfix Product Foam Fill Triple Expanding Filler Pack 750g aerosol can Colour Off white / yellow Base Polyurethane (isocyanate-based) Application Aerosol can Finishing Can be cut, sanded and painted Shrink resistant Yes UV resistant No Use Interior and exterior SafetyUse only in well ventilated areas, wear gloves and eye protection, avoid breathing vapour and wash hands after use. People with asthma or sensitivity to isocyanates should take particular care. Do not puncture or burn the can, and keep it away from heat and ignition sources. Store upright in a cool, secure place away from children and check periodically for leaks. Refer to the Safety Data Sheet (SDS) for full details.
$19.76
Goof Off Professional Strength Remover is a fast-acting solvent remover for sticky, gummy and stubborn mess, supplied here in a handy 177ml can for the garage, workshop or toolbox. It is built to break down stuck-on adhesive residue and marks that ordinary household cleaners struggle to shift, so you can rescue tools, hard surfaces and finished work instead of replacing them.About the formulaA ready-to-use, thin, clear liquid based on a strong solvent blend that includes acetone and xylene. It is poured or wiped on with a cloth rather than sprayed, which gives you control when you are working on small marks or tight spots. Expect a strong solvent smell, so good ventilation matters.Where to use itIndoors: tackling sticker and label residue, tape and glue marks, crayon, pen and marker, chewing gum, candle wax, lipstick and scuff marks on sturdy hard surfaces around the home.Outdoors and in the garage: cleaning up adhesive, tar, asphalt and similar grime from hand tools, and removing dried latex paint drips and caulk smears from suitable hard surfaces.Suitable materials include metal, glass, brick, wood, concrete, grout, fibreglass, hand tools and most automotive surfaces, as well as fully cured varnished or oil-painted surfaces. It is also promoted for marks on carpet and clothing, but test those first.How to use itWear eye protection and gloves and work in a well-ventilated area, away from any ignition source. Test on a hidden spot first, because every surface reacts differently. Apply a small amount to a clean cloth, then blot or lightly rub the mess until it lifts. Thick or layered residue may need a second pass. Wipe the area clean, let the vapours disperse, and reseal the can straight away.Important notesDo not use on plastics, worn vinyl flooring, some automotive paints or some carpets, as solvents can soften, dull or discolour them. Avoid large areas and spot test dyed fabrics and carpet before treating a visible mark. Keep out of reach of children. Always follow the directions on the can.Specifications Brand Goof Off Product Professional Strength Remover (Adhesive Remover) Size 177ml can Form Ready-to-use liquid Colour Clear Base Solvent-based Application Applied with a cloth, blot or rub lightly Use Indoor and outdoor hard surfaces Pack dimensions 55 x 32 x 135 mm SafetyKeep away from heat, sparks, open flames and hot surfaces, and do not smoke. Use only with plenty of fresh air, wear safety glasses and chemical-resistant gloves, and stop work and move to fresh air if you feel dizzy or get a headache. If it contacts skin, remove contaminated clothing and rinse the skin with water. In case of fire use carbon dioxide, dry chemical, foam or water fog. Refer to the Safety Data Sheet (SDS) for full details.
$17.37
Protite Fibreglass Resin is a low styrene emission (LSE) polyester resin for repairing cracks, dents, holes and worn patches on boats, caravans, cars, trailers, gutters and more, supplied here in a 500g size. Mixed with catalyst hardener and used with fibreglass matting or cloth, it gives DIYers and tradies a strong, workable repair material with good adhesion and a consistent wet-out.About the formulaA polyester LSE resin designed for general repair work. Once catalysed it cures to a hard, sandable and paintable finish that resists shrinkage and UV exposure. The resin is a viscous liquid and contains styrene, so it has a strong aromatic odour while you work. It does not cure on its own: you need to add a catalyst hardener (sold separately). Protite also offers a repair kit that bundles the resin with catalyst, matting and application accessories.Where to use itIndoors: repairs to fibreglass, timber, metal and plastic items, models and workshop projects, provided you have good ventilation.Outdoors: caravans, boats, trailers, bikes and cars, plus downpipes, leaky gutters, metal roofs and rusted panels, as well as fibreglass surfboards, pools and tanks.Suitable materials include fibreglass, steel, iron, aluminium, timber, masonry, PVC and smooth polyester surfaces. Test an inconspicuous area first when working on other plastics.How to use itClean the damaged area and remove loose material, grease and dust. Sand the surface so the resin has a key to grip. Pour only the amount of resin you can use in one session into a clean mixing container, then stir in the catalyst hardener. The catalyst manufacturer's guide is 2.5 to 3ml per 100ml of resin on a cold day, or 1.5 to 2ml per 100ml on a hot day. Mix thoroughly with a flat stirring stick until the colour is even. Work the resin into the repair (with matting or cloth if needed) by dabbing or rolling it out slowly to avoid trapping air bubbles. Allow it to cure, then sand and paint as required. Weather, humidity, depth of resin and draughts all change the amount of catalyst you need.Important notesUncatalysed resin will not harden, and too little catalyst or a very thin application can leave the resin tacky or uncured. Too much catalyst makes it gel sooner than expected. The manufacturer indicates the mix starts to gel after about 30 minutes at 25°C, and heat or extra catalyst shortens this while cold or less catalyst lengthens it. Take care when using polyester resin over epoxy surfaces and check compatibility first. Cure times depend on temperature and the amount of catalyst used. Clean tools before the resin cures.Specifications Brand Protite Product Fibreglass Resin (LSE) Size 500g Model number PF-FR0500 Base Polyester resin, low styrene emission Catalyst Required, sold separately Application Hand applied after mixing with catalyst, dabbed or rolled out Finish Sandable and paintable Resistance UV and shrink resistant Use Interior and exterior SafetyUse outdoors or in a well-ventilated area. Wear suitable gloves, eye protection and protective clothing, and avoid breathing vapours. Keep away from heat, sparks and open flames. Store in a cool, dry, well-ventilated place out of direct sunlight and away from ignition sources and incompatible materials, with the lid closed and out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$26.18
Selleys Kwik Grip Horizontal is a flexible, solvent-based contact adhesive that grips the moment two coated surfaces meet, supplied here in a 500ml can for larger bonding jobs. It suits both porous and non-porous materials and has a thicker body that is easy to spread on flat work, making it a handy choice for laminates, rubber, leather, cork and timber around the home, workshop or job site.About the formulaThis is a polychloroprene contact adhesive in a solvent carrier, light amber in colour. The thicker consistency helps it spread without running or stringing, and it is designed for bonding without clamping once the surfaces are joined. The cured bond is flexible, heat resistant up to 130°C, water resistant and holds up against dilute acids and alkalis.Where to use itIndoors: fixing laminate sheet to benchtops and cabinetry, bonding cork, felt and rubber, repairing leather and canvas items, and general workshop or furniture jobs.Outdoors: repairing tents, car covers and other outdoor canvas equipment, and refitting rubber seals, as the cured bond is rated for exterior use.Suitable materials include laminated plastics (such as Laminex and Formica), rubber, leather, canvas, felt, timber, hardboard and compressed board, cork, metals including aluminium, and fibre cement sheeting. Test any other plastic on an offcut first.How to use it Make sure both surfaces are clean, dry and free of dust, grease and loose material. Apply an even coat to both surfaces using a brush or spreader. Leave the surfaces apart until the adhesive is touch dry. This takes about 20 minutes and should not exceed 40 minutes. Line the surfaces up carefully before they meet, using spacers such as dowels on large panels, because the bond grabs immediately on contact. Press the surfaces together firmly, working from one edge, then roll or press with a padded block to bring the whole area into contact. For small porous areas, you can apply to one surface only, join while wet and clamp until dry. Wipe away wet excess with mineral turpentine. Important notesFull bond strength develops in about 24 hours. Do not use on polyethylene or polypropylene. Some plastics, including vinyl sheeting and polystyrene, can be attacked by solvent-based contact adhesives, so test first. Warped or curved surfaces may need clamping. Use only in a well-ventilated area and keep away from heat, sparks and open flames.Specifications Brand Selleys Product Kwik Grip Horizontal Contact Adhesive Pack 500ml can Colour Light amber Base Solvent-based polychloroprene Application Brush or spreader, applied to both surfaces Open time Touch dry in about 20 minutes (maximum 40 minutes) Full strength About 24 hours Heat resistance Up to 130°C Use Interior and exterior SafetyWear protective gloves, protective clothing and eye protection, and use a suitable respirator if there is an inhalation risk. Use outdoors or in a well-ventilated area, keep away from ignition sources and do not smoke. Keep the container tightly closed and store it in a cool, well-ventilated place away from heat. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$28.34
Selleys Kwik Grip Gel Vertical Contact Adhesive is a thick, non-drip contact adhesive made for bonding upright and overhead surfaces, supplied here in a 400g can. The gel body stays put where a runny contact cement would sag, so it suits wall-mounted laminates, panels and other large flat pieces that need to grip the moment they meet.About the formulaA solvent-based polychloroprene contact adhesive in a light amber gel. It works on both absorbent and non-absorbent surfaces. The gel consistency spreads easily with a brush and resists running and stringing. You coat both surfaces, let them become touch-dry, then press them together and the bond grips straight away. Once cured, the bond is water resistant and handles heat up to 130°C. Selleys also notes that the cured adhesive resists dilute acids and alkalis.Where to use itIndoors: laminate and veneer onto vertical panels and cabinetry, cork and felt onto walls or boards, rubber and leather trims, canvas and upholstery-type repairs.Outdoors: weather-exposed fixings on suitable substrates, where a heat and water resistant contact bond is needed.Suitable materials include cork, rubber, felt, canvas, leather, metals, timber, laminated plastics (such as Laminex and Formica), hardboard and compressed board. Do not use it on polyethylene or polypropylene plastics.How to use itMake sure both surfaces are clean and dry before you start. Work in temperatures between 10°C and 35°C. Brush an even coat onto both surfaces, then wait until the adhesive is almost dry to the touch. Press the surfaces together firmly and accurately, because contact adhesives grip on contact and cannot be repositioned afterwards. No clamping is needed. Reseal the can tightly after use.Important notesThe bond grips immediately but reaches full strength after about 24 hours. Do not apply below 10°C. This adhesive is not suitable for polyethylene or polypropylene. Test a small hidden area first on any sensitive or unusual material, such as foam or soft plastics, as the solvents can affect them.Specifications Brand Selleys Product Kwik Grip Gel Vertical Contact Adhesive Pack 400g can Colour Light amber Base Solvent-based polychloroprene Form Non-drip gel Application Brush, to both surfaces Application temperature 10°C to 35°C Set Immediate grip on contact Full cure 24 hours Heat resistance Up to 130°C Use Interior and exterior Can size (approx.) 87 x 87 x 116 mm SafetyKeep it away from heat, sparks, open flames and other ignition sources, and do not smoke while using it. Use it in a well-ventilated area. Vapour may cause drowsiness or dizziness, and the product can irritate skin and eyes. Wear protective gloves and eye protection. Refer to the Safety Data Sheet (SDS) for full details.
$31.83
SikaBond-105 ContactFix is a premium, high strength contact adhesive from Sika, supplied here in a 500mL can for laminate fabrication, upholstery and general sheet bonding. It is a one-component adhesive that dries quickly and gives a strong bond that stands up to heat and moisture, which makes it a practical pick for workshop and trade jobs.About the formulaA one-component polychloroprene (synthetic rubber) contact adhesive. It has a short flash-off time, high initial strength and good resistance to ageing, with a broad adhesion range across common sheet and covering materials. The manufacturer lists a tack-free time of roughly 5 to 8 minutes and heat resistance up to 90°C.Where to use itIndoors: fixing plastic laminates to timber, MDF or particleboard, and covering furniture and joinery with fabric, vinyl or foam.Vehicles and upholstery: Sika lists room-temperature contact bonding of covering materials such as PUR foams and textiles, plus steps, wheel arches, seat brackets and side walls. It also suits cover trims and edging profiles that spring back strongly, and auto and furniture upholstery.Suitable materials include timber, rubber sheets, plastic laminates, fabric, cloth-backed and polyester-backed vinyl, MDF, particleboard, concrete, glass and metal sheets. Test on your actual materials and conditions first to confirm adhesion and compatibility.How to use it Make sure both surfaces are sound, clean, dry and free of dirt, oil, grease, loose coatings and friable material. Apply an even coat to both surfaces. Earlier Sika data sheets list a roller coater, tooth comb, brush or spray gun as suitable methods. Let the adhesive dry until it is tack free (about 5 to 8 minutes, depending on conditions), then bring the surfaces together firmly with strong, even pressure. Take care with positioning, because contact adhesives bond on first contact. Clean tools and equipment while the adhesive is still uncured, using Sika Remover-208, Sika Colma Cleaner or another suitable solvent. Important notesDo not use in temperatures below +10°C or in condensing conditions. For best results, apply at ambient, material and adhesive temperatures within the range stated on the Sika data sheet. Store unopened in the original packaging, dry and out of direct sunlight, between +5°C and +25°C. Shelf life is 12 months from the date of production. Always test compatibility on the real substrates before committing to a full job.Specifications Brand Sika Product SikaBond-105 ContactFix High Strength Premium Contact Adhesive Pack 500mL can Colour Light amber (per current Sika data sheet) Base One-component polychloroprene Density 0.81 kg/L Solids content About 17% by mass Viscosity 350 mPa.s Tack-free time About 5 to 8 minutes Consumption 6 to 8 m² per litre Temperature resistance Up to 90°C Shelf life 12 months from production Clean up Sika Remover-208, Sika Colma Cleaner or other suitable solvent SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Use only outdoors or in a well-ventilated area, avoid breathing vapours, and wear protective gloves, protective clothing and eye or face protection. If it gets on skin, remove contaminated clothing and rinse with water. For fires use alcohol-resistant foam, carbon dioxide or dry chemical, not water. Refer to the Safety Data Sheet (SDS) for full details.
$28.77
Selleys Plastic Wood is a fast-setting, solvent-based wood filling cement for repairing holes, dents and chips in interior timber, supplied here in a 230g maple-coloured tin. It is a simple fix for furniture, skirting, architraves and other indoor joinery, and once set it can be worked much like the timber around it.About the formulaA solvent-based paste containing natural wood fibres, finished in a maple (tan) colour. It dries quickly to a hard finish that holds up to sanding, nailing and planing. Once dry it can be stained, varnished, painted or lacquered, so the repair can be finished in the same way as the surrounding wood. It is a rigid filler, so it is not designed for joints that move.Where to use itIndoors: filling nail holes, dents, chips and small cracks in furniture, doors, window frames, skirting boards, architraves and other interior woodwork.Outdoors: not recommended. The manufacturer rates this product for interior use only.Suitable materials include natural timber and wood veneer.How to use itStir the product thoroughly before use. Make sure the surface is clean, dry and free of loose material. Press the filler in with a putty knife and slightly overfill deeper holes so there is room to sand back flush. Do not fill deeper than 6mm in a single application. Let it dry fully before sanding, staining, painting or lacquering. Wipe the putty knife clean with methylated spirits. Press the lid on firmly after use and store the tin somewhere cool.Important notesNot suitable for exterior use. Not recommended where structural movement may occur, so use a flexible product for joints and gaps between surfaces. Work in a well-ventilated area. Colour is maple only, so test a small area first if you need to match a different timber tone, or plan to stain or paint over the repair.Specifications Brand Selleys Product Plastic Wood Filler Cement Size 230g tin Colour Maple Base Solvent-based, with natural wood fibres Application Putty knife Maximum fill depth 6mm per application Set speed Fast setting Clean up Methylated spirits Use Interior only SafetyThis is a highly flammable solvent-based product. Keep it away from heat, sparks, flames and other ignition sources, and avoid static discharge. It can irritate skin and eyes, and the vapours may cause drowsiness or dizziness. Use only in a well-ventilated area and avoid breathing vapours. Refer to the Safety Data Sheet (SDS) for full details.
$38.42
Turbo Builder's Bog is a trade quality, two part polyester filler for repairing damaged and rotted timber, supplied here in a 500ml can for builders, painters and capable DIYers. It sets to a hard, wood-like finish that you can sand, drill and paint, so it suits window sills, door frames and other jobs where replacing the timber is not practical.About the formulaA polyester-based filler paste that cures by a chemical reaction when mixed with the red hardener paste, rather than by drying out. Because of this, it shows no obvious shrinkage. You choose the working time by adjusting how much hardener you add within the range printed on the can, and the mix also sets faster in warm weather. As it sets it passes through a soft, cheese-like stage where it can be trimmed with a blade or a surform file. Shaping at this point saves a lot of sanding. It spreads smoothly, holds its shape on large fills without slumping, and bonds firmly to timber.Where to use itIndoors: filling holes, gaps and dents in architraves, skirtings, door frames and other timber trims before painting.Outdoors: repairing window sills, sashes, fascias, decks and door frames, including areas where the timber is partly rotten, once the soft material has been cleared back to sound wood.Suitable material is timber. It is designed as a timber repair filler and can be painted over once cured. Test first before using on other surfaces.How to use itMake sure the timber is clean, dry, unpainted, roughened and free of rot. Remove any soft or crumbling material first. Place the amount of filler you need on a clean, flat, non-absorbent surface, such as the plastic over-cap. Add the red hardener in the proportion given on the can, then mix thoroughly until the colour is completely even with no red or white streaks. As a guide from the manufacturer's mixing chart, 100g of filler with 2.5g of hardener gels in about 7 minutes at 22°C. Use less hardener if you need longer working time, particularly in warm weather. Press the mix into the repair with a putty knife or spatula, overfilling slightly. When it reaches the cheese-like stage, trim it to shape with a blade or surform. Allow about 30 to 60 minutes for a full cure, then sand and paint. Mix a small test batch first, because temperature and thickness change the set time.Important notesAlways follow the mix ratio on the can, because too little or too much hardener can affect the cure. Thick fills set faster than thin ones. Timber will still expand and contract with moisture changes, so good woodworking practice should still be followed around the repair. Mixed material generates heat as it cures. Do not leave mixed product in a pile or sealed container. Close the can tightly after use. Check the can and the supplied instructions for full details.Specifications Brand Turbo Product Builder's Bog timber repair filler Size 500ml can Colour Beige / buff paste Base Two part unsaturated polyester filler (cured with red hardener paste) Application Hand applied with a putty knife or spatula Gel time Adjustable by hardener amount; about 7 minutes in the 100g to 2.5g example at 22°C Full cure About 30 to 60 minutes Finishing Sandable, drillable and paintable Use Interior and exterior Country of manufacture New Zealand SafetyIt has a characteristic styrene odour. Use outdoors or in a well-ventilated area, avoid breathing vapours, and keep away from heat, sparks, open flames and other ignition sources. Keep the container tightly closed, out of reach of children, and stored in a dry place. Refer to the Safety Data Sheet (SDS) for full details.
$27.63
![Selleys Plasti-Bond Heavy Duty Bog Two Part Polyester Filler 400g [Off White]](http://gluesaustralia.com.au/cdn/shop/files/Plasti-BondHeavyDutyBog400g_b2b227b8-96d0-4b9a-9dfa-7d64e62b31f5.png?v=1785218520&width=645)
Selleys Plasti-Bond Heavy Duty is a two part polyester filler built for repairs that have to carry load, not simply look tidy. Once the hardener is stirred through, it firms up to a dense, rigid mass in about twenty minutes without the shrinking or cracking that catches out lightweight patching compounds, and it holds its shape well enough to be drilled, tapped and fixed into after curing. The 400g can covers the middle ground jobs that a small pack runs short on. What it is The pack contains an off white polyester putty base and a separate hardener that is mixed in immediately before use. Working time is short, around five minutes at normal room temperature, so the product is mixed in batches rather than all at once. Cured Plasti-Bond can be sawn, drilled, filed, sanded and painted, and the base can be tinted with cement oxides or paint tinters before the hardener goes in if a coloured finish is wanted. Where to use it Indoors: filling holes, cracks and splits in walls, ceilings, floors and doors; rebuilding worn areas around hinges, locks and door handles; making good chipped tiles and ceramics; anchoring bolts and fixtures into masonry; stopping countersunk fastener heads flush in almost any material. Outdoors: patching chipped concrete steps and paths, repairing galvanised guttering and downpipes, and restoring fibreglass, timber and metal on furniture, sporting gear, cars, caravans and boats above the water line. Outdoor repairs should be painted, since the cured filler can discolour if left bare in sunlight. How to use it Prepare the surface so it is clean, dry, unpainted and free of grease or oil. On steel or aluminium panel work that will see vibration, punch or drill the area first to give the filler a positive key. Stir the base thoroughly, then blend in the hardener, working the mix from side to side until the colour is completely uniform. Extra hardener speeds the set in cold weather; less hardener buys time across several separate fills. Apply with a putty knife or spatula, pressing firmly into the repair and slightly overfilling to leave material for sanding. Feather the edges as you go. Take off most of the excess with a Surform or file between roughly twenty and thirty minutes, while it is firm but not yet rock hard. Once fully hard, finish with ordinary files or sandpaper. Paint with water based or oil based paint. Clean tools with mineral turps before the product cures. Important notes Not suitable for continuous immersion or for joints that need to stay flexible. May not adhere to polyethylene, polypropylene or PTFE. Can discolour if left unpainted outdoors. Mix only what you can apply inside the working time; cured material cannot be re-softened. Replace the lid firmly after use and store the can in a cool place. Specifications Brand Selleys Product Plasti-Bond Heavy Duty Bog Pack size 400g Technology Two part polyester putty Appearance Off white paste Working time Approximately 5 minutes at 23 degrees C Cure time Approximately 20 minutes Suitable substrates Metal, timber, brick, fibre cement, fibreglass, concrete, plaster, tiles, ceramics and many plastics Paintable Yes, once cured Clean up Mineral turps before curing Use Indoor and outdoor Safety Polyester fillers and their hardeners are flammable and give off solvent vapour while curing. Work in a well ventilated area, keep the product away from sparks, flames and other heat sources, and wear gloves and eye protection when mixing and applying. Avoid prolonged skin contact and wash any splashes off promptly. Keep out of reach of children, do not allow washings to enter drains or waterways, and dispose of unused material and empty containers in line with local regulations. Consult the current Selleys Safety Data Sheets for the base and the hardener before use.
$42.70
SikaBond-105 ContactFix is a premium, one-component polychloroprene contact adhesive formulated for lamination and laminate fabrication. It offers a broad adhesion range with fast drying and a strong, heat- and water-resistant bond.Features & Benefits Broad adhesion range; easy to apply Short flash-off and fast dry time High initial strength High heat resistance (up to 90°C) and ageing resistance Where to Use Timber, MDF and particleboard Rubber sheets, plastic laminates, fabric, cloth- and polyester-backed vinyl Concrete, glass and metal sheets How to UseApply an even coat to both surfaces, allow to flash off until touch-dry (~5–8 minutes), then join under firm, even pressure. Avoid excess or pooled adhesive, which can trap solvent and weaken the bond.Specifications Chemical base 1-part polychloroprene Colour Light amber Packaging 1 L can Coverage 6–8 m²/L Flash-off time ~5–8 min Temperature resistance Up to +90°C Application temperature ≥+10°C (best at +20°C) Density ~0.81 kg/L Shelf life 12 months StorageStore in original, unopened packaging, dry and out of direct sunlight, between +5°C and +25°C.SafetySolvent-based – ensure adequate ventilation. Uncured adhesive can be removed with Sika Remover-208 or Sika Colma Cleaner. Refer to the Safety Data Sheet before use.
$44.31
Sika Boom Cleaner is an active, solvent-based cleaner for Sika Boom application guns and fresh, uncured polyurethane foam. It quickly removes wet foam residue from equipment and surfaces and cleans grease from contaminated substrates.Features & Benefits Cleans PU foam application guns and equipment Removes fresh, uncured PU foam residue Sprayable, with integral valve for precise application How to UseSpray onto fresh foam, allow 5–10 seconds to react, then wipe away residue with a clean cloth. Cured foam can only be removed mechanically.Specifications Chemical base Solvent-based cleaner Colour Transparent Packaging 500 ml pressurised can Application temperature +5°C to +35°C Density ~0.70 kg/L Shelf life 18 months StorageStore in original, unopened packaging, dry and upright, between +5°C and +25°C.SafetyFlammable aerosol – keep away from ignition sources and do not smoke while applying; ensure adequate ventilation. May dissolve or discolour sensitive substrates such as paint, varnish, plastics and textiles – test an inconspicuous area first. Refer to the Safety Data Sheet before use.
$29.75
Sika Boom AP is a one-component, fast-curing, multi-position polyurethane expanding foam that can be used with the can held in any position. High yield and easy nozzle application make it ideal for fixing, insulating and filling around frames and penetrations.Features & Benefits Multi-position (360°) application High expansion rate and fast curing Very good thermal insulation and sound dampening Can be cut and over-painted; HFC-free Where to Use Window and door frames Pipe entries and air-conditioning vents Roller-blind housings, cavities and voids Specifications Chemical base 1-part polyurethane foam (HFC-free) Colour Light yellow Packaging 500 ml can (nozzle) Tack-free time ~10 min Cutting time ~40–60 min Yield ~25 L per 500 ml can Cured density ~23 kg/m³ Service temperature −40°C to +90°C Application temperature +5°C to +35°C Shelf life 12 months StorageStore dry and upright between +15°C and +25°C, protected from direct sunlight.SafetyNot UV-resistant; pre-dampen the substrate to ensure cure. Pressurised can – keep away from heat and direct sunlight. Refer to the Safety Data Sheet before use.
$26.25
Sika Boom-420 Fire is a one-part, self-expanding polyurethane foam that restores the fire-resistance performance of floors and walls at linear seals, providing up to 180 minutes fire resistance in accordance with AS 1530.4. Its combi-valve allows both gun and nozzle (straw) application.Features & Benefits Up to 180 minutes fire resistance (AS 1530.4), depending on configuration Combi-valve for gun or nozzle application One-part and ready to use; safety valve for extended shelf life Cured foam can be cut, trimmed and sanded Thermal and acoustic insulation Where to Use Fire-rated linear seals in floors and walls Filling and sealing joints requiring fire protection (interior use) Specifications Chemical base 1-part polyurethane foam Colour Pink Packaging 750 ml canister (gun / nozzle) Tack-free time ~7 min Cutting time ~25 min (gun) / ~40 min (nozzle) Yield ~44 L (gun) / ~30 L (nozzle) Cured density 17 kg/m³ (gun) / 30 kg/m³ (nozzle) Service temperature −40°C to +80°C Fire rating Up to 180 min (AS 1530.4); ETA 24/0105 Shelf life 12 months StorageStore dry and upright between +10°C and +20°C, protected from direct sunlight.SafetyInterior use only; not UV-stable; not for structural or mechanical fixing. Pressurised canister – keep away from heat and direct sunlight. Pre-dampen the substrate to ensure correct cure. Always confirm certification requirements with the relevant certifying authority before use in a fire-rated application. Refer to the Safety Data Sheet before use.
$69.38
Sika Boom G is a one-component, fast-curing, gun-applied polyurethane expanding foam with a very high expansion rate. Gun application gives precise control and applicator comfort for fixing, insulating and filling around openings and penetrations, inside and out.Features & Benefits Gun-applied with high expansion rate and fast curing Very good thermal insulation and sound dampening Insulates against temperature, noise, draughts and vermin Can be cut and over-painted; HFC-free Where to Use Fixing and sealing window and door frames Air-conditioning vents and roller-blind housings Pipe and conduit penetrations, cavities and voids Specifications Chemical base 1-part polyurethane foam (HFC-free) Colour Light yellow Packaging 750 ml gun-grade can Tack-free time ~10 min Cutting time ~40–60 min Yield ~40 L per can Cured density ~23 kg/m³ Service temperature −40°C to +90°C Application temperature +5°C to +35°C Thermal conductivity ~0.033 W/mK Shelf life 12 months StorageStore dry and upright between +15°C and +25°C, protected from direct sunlight.SafetyNot UV-resistant; pre-dampen the substrate to ensure cure; do not completely fill hollow sections as the foam expands. Pressurised can – keep away from heat and direct sunlight. Refer to the Safety Data Sheet before use.
$43.13
Dunlop Artificial Grass Adhesive is a high strength, all-weather adhesive from Dunlop Trade (ARDEX Australia), purpose-made for laying artificial grass, outdoor carpet and marine carpet. With excellent water and heat resistance and a bond that stands up to sun, rain and foot traffic, it is the reliable way to keep synthetic turf flat and secure – and it is backed by a 10 year guarantee. This handy 1 litre can is ideal for smaller lawns, edges, joins and repair work.Where to use itDesigned primarily for outdoor projects such as synthetic lawns, pool surrounds, balconies, courtyards and boat decks, and equally suitable for indoor applications like covered patios and utility areas. It bonds securely to concrete, clean paved surfaces, suitably prepared metal, sanded fibreglass and timber.How to useEnsure the surface is clean, dry and free of dust, oil and loose material. Spread the adhesive evenly with a suitable notched spreader or trowel at approximately 3m² per litre, then lay the grass or carpet into the wet adhesive, smoothing outwards to remove air pockets. Weight or roll the surface while the adhesive develops strength and avoid heavy traffic until fully cured.Important notesDo not apply in extremely hot or cold conditions – work between 10°C and 30°C – and never apply when dew or rain is imminent, as moisture can affect bond development before cure.Specifications Size 1 litre can Colour Green Coverage Approx. 3m² per litre Suitable coverings Artificial grass, outdoor carpet, marine carpet Substrates Concrete, pavers, prepared metal, sanded fibreglass, timber Guarantee 10 year guarantee SafetySolvent-based adhesive: use only in well-ventilated areas, keep away from heat, sparks and open flames, and avoid breathing vapours. Wear gloves and eye protection, replace the lid when not in use and keep out of reach of children. Refer to the safety data sheet before use.
$35.99
Dunlop Artificial Grass Adhesive in the value 4 litre can is a high strength, all-weather adhesive from Dunlop Trade (ARDEX Australia) for laying artificial grass, outdoor carpet and marine carpet across larger areas. Formulated with excellent water and heat resistance, it keeps synthetic turf and outdoor floor coverings firmly bonded through harsh Australian conditions, and is backed by a 10 year guarantee. At roughly 3m² per litre, one 4L can covers around 12m² – ideal for full lawns, entertaining areas and commercial installs.Where to use itBuilt for outdoor projects – synthetic lawns, pool surrounds, balconies, rooftops, courtyards and marine decks – and also suitable for indoor areas such as covered patios. It bonds securely to concrete, clean paved surfaces, suitably prepared metal, sanded fibreglass and timber.How to usePrepare a clean, dry, dust-free surface. Spread the adhesive evenly using a suitable notched spreader or trowel, working in sections you can cover while the adhesive is wet. Lay the grass or carpet into the adhesive, smooth outwards to expel trapped air, then roll or weight the surface. Keep traffic off until the adhesive has fully cured.Important notesDo not use in extremely hot or cold conditions – apply between 10°C and 30°C – and do not apply when dew or rain is expected before the adhesive has set. Ensure joins are well supported and seams glued continuously for a lasting result.Specifications Size 4 litre can Colour Green Coverage Approx. 3m² per litre (about 12m² per can) Suitable coverings Artificial grass, outdoor carpet, marine carpet Substrates Concrete, pavers, prepared metal, sanded fibreglass, timber Guarantee 10 year guarantee SafetySolvent-based adhesive: ensure good ventilation, keep away from ignition sources and avoid inhaling vapours. Wear protective gloves and eye protection, reseal the can after use and store away from children. Consult the safety data sheet before use.
$97.56
Oz-Oil Decking Oil is a multipurpose exterior timber oil from Prep Productions, pitched as a five-in-one product: one can covers your deck, outdoor furniture, pergola, fences and gates. Blended from natural plant oils, it soaks into the timber to preserve and seal it from within, leaving a natural, semi-transparent appearance rather than a glossy film. A practical bonus for occasional users: the manufacturer states it is non-evaporative and will not gel in the can, so leftover oil keeps for the next job rather than going to waste.Formula overviewA blend of natural seed oils and waxes carried in dipentene, a citrus-derived solvent. The oil is lightly pigmented and semi-clear with a citrus odour, and works by penetrating the boards rather than coating them.Where to use itOutdoor: external timber including decking, cladding, railings, joists, bearers, rafters, pergolas, garden furniture, fences and gates.Indoor: not intended for interior use. This is an exterior timber oil.How to use Stir well before use, as the oils may settle in the can. Make sure the timber is clean, dry and free of old coatings. Follow the can label for preparation guidance. Apply with a brush or lambswool applicator. Apply 2 coats, allowing 24 hours before recoating. Coverage is up to 12 square metres per litre depending on timber porosity. Important notes The finish is semi-transparent. It enriches the timber tone but will not deliver an opaque or solid colour. Like all penetrating oils, results depend on surface preparation. Weathered grey timber should be cleaned back to sound wood first. Check the can label for clean-up directions and detailed preparation steps. Specifications Size 4 litres Base Natural seed oils and waxes in citrus-derived dipentene Coats 2 Recoat time 24 hours Coverage Up to 12 m² per litre Finish Transparent matt, natural semi-transparent tone Application Brush or lambswool applicator Shelf life Non-evaporative, does not gel in the can Made in Australia SafetyCombustible liquid (flash point around 68°C). Keep away from heat, sparks and open flames, and store below 30°C, tightly closed, in a well-ventilated area away from strong oxidisers. Rags soaked in decking oil can self-heat and spontaneously combust: lay used rags flat to dry outdoors or soak them in water before disposal. May irritate skin and can cause an allergic skin reaction in people sensitised to citrus solvents, so wear gloves when applying. Refer to the Safety Data Sheet (SDS) for full details.
$64.68
Organoil Woodguard is a deeply penetrating oil treatment made to look after brand-new exterior timber in the period between installation and final finishing. Fresh hardwood often carries high moisture and, left bare, can cup, split, crack or bleed tannins as it dries out. Woodguard soaks into the boards and stabilises them while they acclimatise, so the timber arrives at oiling day in sound, even condition. It is made in Australia by Prep Productions and formulated for harsh Australian and New Zealand exposure.Formula overviewA natural-oil blend built around tung oil and beeswax, carried by dipentene, a citrus-derived solvent. Rather than forming a film on top of the wood, the blend penetrates the timber surface, which is why it is applied as a single coat and later over-coated with a finishing oil.Where to use itOutdoor: new, raw timber decking, joists, bearers, cladding, posts, rails and exterior joinery. Particularly recommended for dense or high-moisture hardwoods such as spotted gum and plantation species before they are oiled.Indoor: not intended for interior finishing. Woodguard is an exterior pre-treatment, not a furniture or floor finish.How to use Stir well before use, as natural oils can settle. New raw timber can be treated directly. Timber that has already weathered in the elements should first be cleaned with a timber wash such as Organoil Wash-A-Way. Apply one coat only, using a brush or lambswool applicator. Coverage is up to 12 square metres per coat depending on timber density and porosity. Allow the treatment to dry fully before applying your finishing oil. Follow the can label for drying guidance. Important notes Woodguard is an interim protectant, not a final finish. Plan to apply a decking or exterior timber oil afterwards. Designed as a one-coat application. Do not over-apply. For new or raw untreated timber only. Previously coated timber should be stripped and washed first. Specifications Size 4 litres Base Solvent-borne natural oils (tung oil, beeswax, citrus-derived dipentene) Coats 1 Coverage Up to 12 m² per coat Finish Matt, natural Application Brush or lambswool applicator Made in Australia SafetyCombustible liquid (flash point around 61°C). Keep away from heat, sparks and open flames, and store below 30°C in a tightly closed container in a well-ventilated area. Rags and applicators soaked in this product can self-heat and spontaneously combust: lay used rags flat to dry outdoors or soak them in water before disposal. May irritate skin and eyes and can cause an allergic skin reaction in sensitised people, so wear gloves and eye protection. Refer to the Safety Data Sheet (SDS) for full details.
$84.56
Glitz Borax is a versatile cleaner and laundry booster that tackles grime, helps remove stains, and deodorises around the home. This mineral based powder dissolves in warm water to lift dirt, cut through residues, and freshen hard surfaces and fabrics. Why you will love it Multi purpose performance for laundry, kitchen, and bathroom Helps remove tough stains and lingering odours Boosts detergent effectiveness in hard water Deodorises bins, drains, and pet areas Free from added fragrance and chlorine Where to use Laundry booster for everyday washing Tiles, grout, sinks, and benchtops Toilets and bathroom surfaces Bins, outdoor furniture, and patios General deodorising tasks How to use Laundry booster: Add 1 to 2 tablespoons to the wash with your usual detergent. For heavily soiled loads use up to 1/4 cup. Dissolve in warm water for best results. Multi surface cleaner: Dissolve 2 tablespoons in 1 litre of warm water. Wipe surfaces with a cloth or sponge. Rinse food contact areas with clean water after cleaning. Stain pre soak: Dissolve 2 tablespoons in 2 litres of warm water. Soak colourfast fabrics for up to 30 minutes. Rinse well before washing as normal. Always patch test first. Deodorising paste: Mix borax with a little water to form a paste. Apply to tiles or grout, lightly scrub, then rinse. Bin and drain freshen: Sprinkle 2 to 3 tablespoons in the bin base or dissolve in warm water and flush down the drain. Rinse thoroughly. Good to know Use on sealed hard surfaces only Check fabric care labels and test on a hidden area first Not suitable for wool, silk, leather, or aluminium What is in the pack Glitz Borax powder 1 kg resealable pack Specifications Product type Multi purpose cleaner and laundry booster Form Free flowing powder Size 1 kg Fragrance None added Safety and storage Read and follow the label before use Wear gloves for prolonged contact Avoid inhaling dust. Use in a well ventilated area Keep out of reach of children and pets Do not ingest. Do not use on skin or as a personal care product Store in a cool dry place with the pouch sealed Disposal Rinse empty packaging and dispose of it in accordance with local council guidelines. Frequently asked questions Can I use it in cold waterYes, but it dissolves more readily in warm water. Pre dissolve in a small amount of warm water when using cold cycles. Is it safe for septic systemsUse sparingly and flush well with plenty of water. Follow any appliance and system guidelines. Will it bleach coloured fabricsIt does not contain chlorine bleach. Always check colourfastness and test on a hidden area first.
$12.22 $9.45
Dunlop Gripper Fast Tile Adhesive 500 ml Overview Dunlop Gripper Fast Tile Adhesive 500 ml is a high quality multipurpose adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials common building materials ceramics wood metals some plastics stone Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Apply between 10°C and 30°C. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Cure time varies with product and conditions. Allow adequate time before loading or finishing. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean uncured product with a suitable solvent or water as applicable. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. Do not ingest. Refer to the Safety Data Sheet (SDS) for full details. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$32.80
Gyprock CSR Acrylic Stud Adhesive 1 kg is a reliable acrylic stud adhesive for secure plasterboard fixing chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 1 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Gyprock CSR CSR for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Gyprock CSR Acrylic Stud Adhesive 1 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Fixing plasterboard to studs and battens Reducing the chance of nail pops and drumminess Suitable surfaces The adhesive works well on the following surface types when properly prepared: Timber framing and battens Metal studs as directed by code Back of plasterboard Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of install sheets within the wet time window. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Apply daubs as specified, then fix sheets with screws or nails. Adhesive cures to a resilient bond that complements mechanical fastening. Temperature and environmental performance Use in moderate temperatures for consistent cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean fresh residue with a damp cloth. Scrape away cured beads before setting coats. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed. Do not allow to skin in the tub. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$23.57
Sika® Filler One Strike Maxi is revolutionary ready-mixed lightweight filler for the preparation of numerous surfaces prior to painting or wallpapering. For filling on plaster, brick, stone, wood and render. Fills in one go- No need to build up layers of filler – fills up to 75mm deep in one application No sanding or sagging Fast drying and easy to sand CHARACTERISTICS AND ADVANTAGES Fills in one go- No need to build up layers of filler – fills up to 75mm deep in one application No sanding or sagging Fast drying and easy to sand Internal/external use Overpaintable Overstainable Easy to use Dries brilliant white COLOUR: White Sika® Filler One Strike is revolutionary ready-mixed lightweight filler for the preparation of numerous surfaces prior to painting or wallpapering. Based on high strength lightweight polymeric fillers, the product outperforms conventional fillers in most applications Designed for professional and D.I.Y use. Uses Sika® Filler One Strike 1 is suitable for filling of gap in: Plaster Brick Stone Wood Render Characteristics Advantages Fills in one go- No need to build up layers of filler - fills up to 75mm deep in one application. Easy to use - lightweight paste is incredibly easy to apply. No sanding required - finishes to a smooth surface. No sagging - the lightweight properties of Sika® Filler One Strike prevent sagging even on ceilings. Non-shrink - will not shrink back whilst drying. Quick drying - ready to paint/paper in just 30 minutes. Overpaintable with most solvent based and emulsion paints. Overstainable Internal/external use. Dries brilliant white Product Data Appearance / Colour Lightweight brilliant white paste Packaging 300 ml cartridge Storage Storage Conditions / Shelf-Life 24 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost. Technical Data Chemical Base Filled water based polymer dispersion. Density ~ 0.49-053 kg/l Solid Content ~ 61% (w/w) pH 8.0 – 9.0 Grading Dmax : 0.12 mm Layer Thickness Maximum Width: 50 mm Maximum Fill: 75 mm System Information Application Details Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 cartridge of Sika® Filler One Strike yields 0.3 m 2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +30°C max. Ambient Temperature +5°C min. / +30°C max. Application Instructions Mixing Sika® Filler One Strike is supplied ready to use - no mixing is required. Application Method / Tools Apply direct from pail with spatula/spreader. Smooth over surface and allow drying. Sanding is not normally required although the product may be sanded if required. Sika® Filler One Strike can be painted over after approx. 30 minutes using water based paints. Leave to dry for 12 hours when using solvent based paints. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: Note: ~ 30 minutes at 20°C The drying time correspond to thin layer thickness. If deep holes or cracks are filled, longer time is required in order for the product to harden in its full thickness. Notes on Application / Limitations • Do not use to fill plastic or metals. • Do not apply when rain is imminent (external use). • Do not apply in temperatures (ambient and surface) below 5°C. • If using externally overpainting is essential
$13.00
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour. Features Easy to use. Can be applied by hand or with a putty knife Product has exceptional keeping qualities Available in a natural colour Superior grade putty Where can this putty be used? A wood sash putty that is excellent for glazing wooden windows and doors Bedding glass beads Not recommended for use with heat absorbing glass If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes Not recommended for use where structural movement may occur Not recommended for use in metal framed windows. What materials is this putty suitable for? Wood Timber How to use this product Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing. Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used. Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass. Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing. Paint should be carried out 2mm above the top line of the putty. Handy tips Do not use kerosene, turps or other material to aid in working the putty Allow putty to skin before applying paint Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it. Putty must be painted in exterior applications. High humidity, cold weather and use in interior applications can extend skinning times. Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil. Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen. Safety tips Low hazard material For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
$12.18
You have seen 48 out of 79 products
Paint-style cans for decanting or brush/roller application across laminates, floors and panels. Confirm recommended film thickness and recoat/assembly windows. Use filters to refine by chemistry, open time and clean-up. Always follow the product page and TDS/SDS.
