🌍 Worldwide Shipping Available | Fast & Secure Delivery ✈️

Edge Sealing

121 products

  • Timbermate Woodfiller putty crack filler Interior 2Kg [Jarrah] Timbermate Woodfiller putty crack filler Interior 2Kg [Jarrah]

    Timbermate Timbermate Woodfiller putty crack filler Interior

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Timbermate Wood filler is an Interior grade 4 in 1 Wood Putty, Grain Filler, Edge Filler and Crack Filler. When thinned slightly with water can also be used as a sanding sealer. Timbermate does not shrink, sink, crack or fall out and has an indefinite shelf life. It is non-flammable, non-toxic and can be used to the last gram. The secret ingredient of Timbermate is tap water, therefore, containing no Acrylic, Latex or Solvents. Timbermate comes in 13 premixed colours plus Natural Tint Base. Timbermate takes all types of known stains, varnishes and coatings. The Timbermate formula is over 85 years old and is the only genuine water-based formula in the world proving that the formulation has stood the test of time. Features & Benefits of Timbermate No Waste, Usable to the last drop. If tub dries out just add water to soften. Won't Shrink, Sink, Crack or Fall Out. Suitable for use in all Timbers including Particle Board M.D.F. (Custom Wood) *Plaster Board, Flooring, Panelling etc. Can be used as Wood Putty, Sanding Sealer, Prime Coat, Grainfiller, Crackfiller, Undercoat & Edge Filler all in one. Available in 13 Timber Tones plus Natural. Use White for top coats only. Can be tinted in wet state or overstained when dry. Use any type of Colorant i.e. Water Based Spirit based ochers etc. Easy sanding, will not clog paper when DRY Sanded dust can be mixed with water for re-use. Fast drying approx. 20-30 min, but can be heat dried with a heat gun or lamp for faster drying. Temperature can affect drying time. Clean hands or tools with water. Non-Flammable, Non-Toxic, Non-Yellowing. Solvent, Latex and Acrylic Free. Heat Proof and Freezeproof. Provides a strong foundation for all top coats inc. Single & two pack products polyurethane's, oils, acrylics, french polish wax etc. Takes nails, screws, planing, sawing, drilling and routing Can be used on Metal, Plastic, Fibreglass and in Foundries. 100% Australian Made and Owned. Available in pack sizes of 250g, 500g, 2Kg, 8Kg, 20Kg and 200Kg. Interior Grade. Edgefiller Apply TIMBERMATE with a spatula or knife using hand pressure to force into the Edge or End of the grain. For spray gun use stir 10%-15% water into TIMBERMATE fit a 2mm mozzle and set pressure to 60psi. Boards can be stacked for easy spraying. Allow to dry and sand with a fine grit paper and apply topcoat. Woodfiller/Wood Putty Fills cracks, knots, pin and screw holes, splits, blemishes, etc. Fill deep holes in layers allowing time for each layer to dry. Will not blind natural wood grain. Drying time is about 30 minutes. TIMBERMATE dries hard and smooth without shrinking or sinking and can be belt or drum sanded as it is not affected by heat, the hotter it gets the harder and faster it sets and that means less "Down Time."  You can speed dry TIMBERMATE by adjusting the surrounding air temperature. This can be done by using either hot air, heat lamps, or kiln ovens.TIMBERMATE can be mixed with any stains before or after the filler is dry. To match medium and darker shades mix with Natural, Pine or other light shades. Use white TIMBERMATE only for white top coats. Grainfiller Mix 10% to 15% water into TIMBERMATE to make a perfect Grainfiller, Sanding Sealer and Prime Coat all in one application. First sand surface and with fine grit sandpaper, then apply Grainfiller to surface with a spray gun, paint roller, hessian or a cloth rolled into a ball, rub across the grain in a circular motion finishing with the grain. Sand, once filler is dry, to perfection with either sandpaper or power sander, using a fine grit paper. Grain filer can be used in a Roller or Curtain Coater or Spray Gun using a 2mm nozzle and 60psi pressure. Can be further thinned down with water if required. MDF Due to the finishing system used to manufacture MDF, it is essential to seal the job with a water-based non-acrylic product before applying top coats. Therefore TIMBERMATE meets your needs. Flooring Preparing old floors: Scrape all dust and waste between boards and surface as well as from knot holes and nail heads, vacuum well and carry out first sanding to prepare for filling and coating. Ensure that floor is stabilised, dry and free of movement. Application new floors and prepared old floors: Fill cracks, knot and nail holes and all blemished with a putty knife. Fill deeper holes in layers of about 6mm allowing each fill to dry. Apply TIMBERMATE to the entire floor, as a sealant, using a squeegee, trowel or paint roller. Allow to dry and sand off with a fine paper - 120 to 150 grit is recommended for best results. The floor can now be stained or varnished. Frequently Asked Questions Question: Is TIMBERMATE toxic, flammable or harmful? Answer: It is advisable to carry out safe work practices, as you would when working with dust. (Use an approved dust mask and safety goggles). TIMBERMATE contains no harmful ingredients and is non-flammable. Question: Can TIMBERMATE be used externally? Answer: No, as TIMBERMATE® is resoluble in water it is not advisable to use it outdoors. TIMBERMATE IS RECOMMENDED FOR INTERIOR USE. For external use, we recommend Earls MulTFill, Powder Putty or Porion Flexible Filler. Question: Can TIMBERMATE be used with stains and other finishes? Answer: Yes, TIMBERMATE® will take all types of known stains, coatings and colourants which can be Water based, Oil based, Solvent or Spirit based and even Acid Catalysed Lacquers. Question: Can TIMBERMATE be grainfilled? Answer: Yes, TIMBERMATE is a non-solvent based filler and is ideal for grainfilling. Mix 10-15% hot water to thin the Timbermate, then rub over the grain or spread thinly (see below for more detailed instructions). TIMBERMATE will: *Not raise the grain *Not damage the grain TIMBERMATE is: *Easy to sand when dry *Easy to stain when dry *Heat proof so you can speed the drying time by heating with a hair dryer, heat gun, lights etc. Question: How is the grainfiller applied? Answer: Take some TIMBERMATE out of the tub and place it in a separate container. Add approximately 10-15% water, (1gm=1ml) and mix into a slurry like paste (like toothpaste). Use a LINT FREE CLOTH AND RUB ACROSS THE GRAIN. When grainfiller goes "whitish" and sands off easily like talc powder, it is dry. TIMBERMATE will not blind the sandpaper (ie. clog up). If sandpaper gets clogged the grainfiller is not dry. Sand off in the same direction as the grain. Stain or coat when dry. Question: When is the stain applied? Answer: You can stain before or after applying TIMBERMATE (see "How do I match colours"). Question: How are the colours matched? Answer: Colour matching is easy. You can do it either of the following ways: Add your colourant to the putty and match the exact colour whilst wet. TIMBERMATE will dry lighter, but coat back to its original wet colour once coated with clear finishes. The final result is what you see (wet) is what you get. You can stain TIMBERMATE once it is dry. To test if dry, just rub sandpaper over putty. If putty clogs the sandpaper the filler is still wet. Wait for TIMBERMATE to dry and then stain. Question: How long does TIMBERMATE take to dry? Answer: Depending on the weather and depth of fill, TIMBERMATE will dry as follows: In hot weather, TIMBERMATE dries quicker. In cold weather, the depth of fill will determine the drying time. You can speed up the drying time by using a heat gun, hair dryer or light. Question: What depth or width can be filled? Answer: Do not fill holes deeper than 6-8mm at a time. TIMBERMATE dries quicker when filled in layers. Allow TIMBERMATE to dry between layers. Question: Why is the tub hard some days and feels dry and soft on other days? Answer: TIMBERMATE is waterbased. It contains no harmful solvents or acrylics and is, therefore, temperature sensitive. The warmer the weather or environment the softer the putty. On hot days it will start to dry in the tub if not properly sealed. Add a few drops of water to re moisten. Question: How is TIMBERMATE softened? Answer: Add a few drops of warm water to the top of the tub. It will soften quite quickly. If tub is frozen, thaw out by standing tub in a tub of hot water or place in a microwave for 20 seconds. TIMBERMATE is freeze thaw stable. Question: Can TIMBERMATE be used for any other purpose other than wood repair? Answer: TIMBERMATE does not shrink, sink, crack or fallout and can, therefore, be used on Plasterboard, Masonry, Fibreglass, Plastic and any other surface. Bearing in mind that steel must be coated with a primer to avoid rusting. Question: Can TIMBERMATE go off or does it have a shelf life? Answer: TIMBERMATE has an unlimited shelf life and will last indefinitely. If contents become dry merely add a few drops of water to reconstitute. DO NOT add more water than is necessary or leave excess water in the tub for a long period of time. The trapped excess water in the tub will cause the putty to become contaminated and will start to degenerate. Question: Why are so many colours available? Answer: We manufacture 13 colours to match almost all shades and types of timber. If you are using a clear coat you must match your putty colour. If staining, use Natural (tinting base). Question: What is Tint Base (Natural) putty and why? Answer: Tint Base (Natural putty) is putty in its natural state uncoloured. You may add the lightest shade of tint to change its colour. Question: Can TIMBERMATE be used on floors? Answer: TIMBERMATE is ideal for filling cracks, gaps, and nail holes in floors. TIMBERMATE will enhance the grain on the floor. As it does not shrink, sink, crack or fall out it is highly recommended for all floors. Question: Can TIMBERMATE be used with French Polish and Waxes? Answer: You can use all types of Waxes, Shellac and Oils on TIMBERMATE. Question: How is an incorrect match or badly filled hole fixed? Answer: Errors can be fixed with ease. If TIMBERMATE is not coated then wash out. If already coated, then break the top coat and then wash out. Refill or rematch if necessary. Question: Is TIMBERMATE Australian owned and manufactured? Answer: Yes. TIMBERMATE is 100% Australian owned and manufactured. An all Australian dedicated workforce does all manufacturing in our Melbourne factory.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $0.00 - $89.00

  • Sikaflex 291 Tube Black Marine-Grade Polyurethane Sealant 150ml Sikaflex 291 Tube Black Marine-Grade Polyurethane Sealant 150ml

    Sika Sikaflex 291 Tube Black Marine-Grade Polyurethane Sealant 150ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikaflex®-291 Black Marine-Grade Polyurethane Sealant 150mL is a premium, one-component, non-sag adhesive sealant specially formulated for marine environments. It cures on exposure to atmospheric moisture, forming a strong, elastic, and durable bond that resists saltwater, vibration, and weathering. Trusted by boat builders and marine professionals worldwide, Sikaflex®-291 meets International Maritime Organisation (IMO) standards for safety and performance. Features & Benefits Marine-grade polyurethane formula with superior adhesion Excellent weathering and saltwater resistance Elastic and vibration-resistant for long-lasting seals Low odour and non-corrosive composition Can be sanded and overpainted after curing Maintains flexibility across wide temperature ranges Where to Use Sealing and bonding on boats, yachts, and marine structures Deck fittings, hatches, and hardware installations Elastic, vibration-resistant joints above and below deck Bonding wood, metals, primers, coatings, ceramics, and GRP plastics Important Notes Not suitable for plastics prone to stress cracking such as Plexiglas or Polycarbonate Surfaces must be clean, dry, and free from grease or dust before application Recommended application temperature: 5°C to 40°C Technical Details Chemical Base 1-component polyurethane Colour Black Cure Mechanism Moisture-curing Density (uncured) Approx. 1.3 kg/L Shore A Hardness 40 Tensile Strength 1.8 MPa Elongation at Break 500% Temperature Resistance -50°C to +90°C (up to 180°C short term) Skin Time Approx. 60 minutes Shelf Life 12 months (stored below 25°C) Packaging 150 mL Tube For marine sealing and bonding you can trust, Sikaflex®-291 delivers professional-grade strength, flexibility, and durability on every project.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $18.70 $0.12/ml

  • Selleys No More Gaps Coloured Caulk Sealant 450g [Brilliant White] Selleys No More Gaps Coloured Caulk Sealant 450g

    Selleys Selleys No More Gaps Coloured Caulk Sealant 450g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    No More Gaps Coloured Gaps No More Gaps Coloured Gaps offers a long-lasting, colour-matched finish, suitable for both interior and exterior use. It comes in a wide range of colours, with no need to paint over (although it is paintable if required). It provides superior flexibility to cope with building movement, hiding cracks and gaps longer, with greater than 350% elongation/stretch and up to +/- 20% movement capability. Key Features Long-lasting, colour-matched finish Suitable for Interior & Exterior use Available in a great colour range, with no need to paint over (Paintable if required) Superior flexibility to cope with building movement, hiding cracks and gaps longer Greater than 350% elongation/stretch and up to +/- 20% movement capability Good resistance to weathering Superior adhesion to a broad range of surfaces, resulting in a lasting finish Mould and mildew resistant Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles (not exposed to water) In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Bare or painted surfaces Colorbond Many other building materials How to Use Ensure the surface is clean, dry, and free from dust, grease, flaking/powdery paint, and old or crumbling caulk. Cut the seal and nozzle, fit it to the top of the cartridge, and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking Gun. Hold the caulking gun at a 45° angle and apply, forcing the product into the gap. Smooth with a wet finger or spatula. Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow surface to skin thoroughly prior to painting with water-based paints. If using oil-based paints or for large gaps, allow the sealant to set for about 24 hours and ensure the product is completely cured. Avoid water contact until fully cured – 72 hours or longer in cold weather. Limitations Not recommended for foot traffic areas, gaps between tongue and groove boards, or weatherboard overlaps. Use Selleys No More Gaps Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards, and Selleys No More Gaps Exterior & Weatherboard Gap Filler for weatherboard overlaps. Not suitable for areas in prolonged contact with water (e.g., showers, pools, & spas). Use Selleys Silicone Sealant for significant joint movement or areas of frequent water immersion. Do not apply or store below 5°C. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easier cleanup. When first applying, extrude a small amount onto scrap material to ensure smooth, continuous flow of gap filler. If wiping off excess with a wet finger, wet it with water (not saliva) to avoid bacteria that can promote mould growth. Allow surfaces to skin before painting, approximately 30 minutes. Protect from rain until the surface is firmly skinned. Some water-based undercoats and flat paints may crack when drying. To reduce this, allow the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting. Keep a pack of Selleys Sugar Soap Wipes handy for easy cleanup. Clean Up Water-based, so clean up with water. Uncured product may be removed with water. Cured product can be removed by sanding and scraping. Size 450g Cartridge Colours Black Brilliant White Brown Cedar Charcoal Coffee Cream Ivory Light Grey Technology Water-Based Use Interior & Exterior

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $0.00 - $15.00

  • Sika Sikaflex®-111 Stick & Seal White: 1-Part Adhesive & Sealant 290ml

    Sika Sika Sikaflex 111 Stick & Seal 1-Part Adhesive & Sealant 290ml [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $23.00

  • Selleys Marine Flex For Boats Pools and Spas Water Proof [White]

    Selleys Selleys Marine Flex For Boats Pools and Spas Water Proof [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Marine Flex is a high-performance adhesive and sealant designed for marine and water-exposed applications. Using Sil-X advanced polymer technology, it provides a permanent watertight seal above and below the waterline, even in salt, fresh, or chlorinated water. Key Features Cures and bonds underwater No primer required for most surfaces Strong and flexible bond absorbs vibration and movement Solvent-free and isocyanate-free formulation Sandable once cured 10-year watertight seal guarantee (above waterline) Where to Use Ideal for marine, pool, spa, and construction projects where water exposure or movement is expected. Suitable for bonding and sealing: Boat hulls, fittings, and deck seams Pool tiles, coping, and skimmer boxes Concrete, fibreglass, sealed timber, and metal surfaces Glass, ceramics, and most rigid plastics Technical Details Technology Sil-X advanced polymer Colour White or Black Size 410g cartridge Finish Smooth, paintable once cured How to Apply Ensure surfaces are clean and free from grease, oil, or dust. Can be applied to damp or wet surfaces. Cut the nozzle to the desired bead size and apply using a standard caulking gun. Tool the sealant immediately with a soapy water solution before it begins to skin. Allow to cure fully before sanding or painting if required. Limitations Not suitable for polyethylene (PE), polypropylene (PP), or PTFE materials Gelcoat surfaces should be lightly sanded before application The watertight guarantee applies to applications above the waterline Why Choose Selleys Marine Flex When you need a sealant that can withstand constant water exposure, movement, and vibration, Selleys Marine Flex delivers unmatched reliability. It bonds powerfully, stays flexible, and ensures a lasting waterproof finish for marine, pool, or construction applications.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $28.00

  • Selleys No More Gaps Multipurpose Sealant Filler 475g [White]

    Selleys Selleys No More Gaps Multipurpose Sealant Filler 475g [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 300% elongation/stretch and up to +/- 15% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage. Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application). Is formulated for long term resistance to cracking and crumbling. Easy water clean-up Will not stain building materials. Has good resistance to weathering. Low toxic, low odour, low VOC, less harmful to the environment Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles which are not exposed to water In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm  What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Paint Many other building materials

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $5.00

  • Selleys All Clear Crystal Multipurpose Sealant for Wet, Oily & Dirty Surfaces Paint, Mould & Water Resistant

    Selleys Selleys All Clear Crystal Multipurpose Sealant for Wet, Oily & Dirty Surfaces Paint, Mould & Water Resistant

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys All Clear Crystal: The Ultimate Multipurpose Sealant Key Features Works on wet, oily, and dirty surfaces Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Best For Metal, Timber, Glass, Glazed tiles, Brick, Stone, and many plastics (may damage polystyrene and polycarbonate). Applications Sky lights Window frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' entries Shower screens Sinks and basins Caravans and recreational vehicles How to Use Use only in a well-ventilated area. Ensure surface is clean and dry. Apply with a caulking gun and smooth with a tool dipped in turps. Limitations May damage some plastics Not for permanent water immersion Not suitable for use over silicones or polystyrene foam Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by cutting and scraping. Technology & Cure Time Solvent-based, with a full cure time of 48-72 hours. For both interior and exterior use.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $16.00

  • Sika SikaSeal Roof & Gutter Silicone Sealant [Black] Sika SikaSeal Roof & Gutter Silicone Sealant [Grey]

    Sika Sika SikaSeal Roof & Gutter Silicone Sealant

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    SikaSeal® Roof & Gutter Silicone Sealant Product Type: 1-component neutral cure roof and gutter silicone sealant Product Overview SikaSeal® Roof & Gutter is a versatile, one-component, neutral curing silicone sealant designed for use in roofing and guttering applications. This sealant offers excellent adhesion to a variety of construction materials and is ideal for sealing roofs, gutters, and plumbing fixtures, both for exterior and interior applications. It cures quickly and provides a flexible, waterproof seal with superior temperature resistance. Key Features Neutral cure, low odour formula Excellent adhesion to common construction materials such as glass, metals, ceramics, tiles, plastics, concrete, and rubber Fast curing with a non-sag formula for easy application Interior and exterior use with a temperature resistance range of -40°C to +150°C High movement capability (±25% for translucent, ±50% for coloured variants) Waterproof seal for durable, long-lasting performance Non-toxic and water-potable approved per AS/NZS 4020:2018 Applications SikaSeal® Roof & Gutter is ideal for: Roof and gutter sealing Sealing polycarbonate roof sheeting General sealing around plumbing fixtures and penetrations Sealing interior and exterior joints Specifications Packaging 300ml cartridge Shelf Life 12 months (if stored properly) Colours Available Translucent, Grey, White, Black Density Translucent: ~1.02 kg/l, Colours: ~1.39 kg/l Shore A Hardness Translucent: ~26, Colours: ~46 Elongation at Break Translucent: ~250%, Colours: ~310% Movement Capability Translucent: ±25%, Colours: ±50% Service Temperature -40°C to +150°C Application Instructions Ensure the substrate is clean, dry, and free from oils, grease, dust, and other contaminants. For optimal adhesion, follow the recommended priming procedures based on the substrate type (non-porous or porous). Apply SikaSeal® Roof & Gutter using a sealant gun, ensuring full contact with the joint sides. Tool the sealant immediately after application for a smooth, durable finish. Important Considerations Do not apply on natural stone or bituminous substrates Not recommended for use under water pressure or in permanent water immersion Pre-test required on stressed polyacrylate and polycarbonate materials May cause discoloration on light-colored silicone when exposed to UV radiation (this does not affect the product's performance) Not suitable for use in confined spaces with no air circulation (requires atmospheric moisture to cure) Packaging & Storage Store in the original, unopened packaging in a dry location between +5°C and +25°C. Shelf life is 12 months from the production date under proper storage conditions. Contact & Ordering For more information or to place an order, contact us at admin@gluesaustralia.com.au

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $13.00

  • Sika SikaSeal Flexible Gap Filler Super-200 Paintable [Transparent]

    Sika Sika SikaSeal Flexible Gap Filler Super-200 Paintable [Transparent]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    SikaSeal® Super-200 is great for sealing of connection joints with moderate movement Good UV resistance Low odour For exterior and interior use USE Sealing of connection joints with moderate movement around windows, window sills, doors, PVC pipes, dry partition walls and ceiling Filling of cracks on interior and exterior walls (with no permanent water immersion) CHARACTERISTICS AND ADVANTAGES For exterior and interior use High movement capability ±12.5% Good UV resistance Solvent-free, low odour Overpaintable Very good adhesion on most construction materials such as concrete, plaster, wood Possible storage at -10°C for short period of time (max 24h) Conforms to EN 15651-1 F INT EXT

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $7.80

  • Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]

    Sika Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikaflex-227 is a one-component poly­­urethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $27.48

  • Sikaflex Crystal Clear Multipurpose Sealant & Adhesive 290ml

    Sika Sikaflex Crystal Clear Multipurpose Sealant & Adhesive 290ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces 100% crystal clear / transparent Good workability Very good adhesion on many typical building materials Use: Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including: Plasterboard Wood surfaces Painted enamel Polyester Plastic Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions. CHARACTERISTICS AND ADVANTAGES 100% crystal clear / transparent Good workability Low shrinkage during cure Flexible and elastic Can be used on damp concrete Very good adhesion on many typical building materials COLOUR: Transparent Product Data Appearance / Colours Transparent Packaging 300 g cartridge (290 ml), 12 cartridges per box Storage Conditions / Shelf-Life Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met. Technical Data Chemical Base Silane terminated polymer Density 1.05 kg/l approx. (ISO 1183-1) Tensile Strength 2.0 N/mm2 approx. (ISO 37) Shore A Hardness 30 approx. (after 28 days) (ISO 868) Elongation at Break 400% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Service Temperature −40 °C to +70 °C SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department. Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly. Bonding After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again. Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear. Sealing After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $27.65

  • Sikasil Pool Neutral-Cure Silicone Sealant 300 ml [White]

    Sika Sikasil Pool Neutral-Cure Silicone Sealant 300 ml [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikasil® Pool Neutral-Cure Silicone Sealant – 300 ml Cartridge Designed for use in demanding aquatic environments, Sikasil® Pool is a one-part, neutral-curing silicone sealant formulated specifically for swimming pools, wet areas, and permanently submerged joints. With exceptional resistance to chlorinated water, high elasticity, and outstanding fungal resistance, this sealant delivers durable, long-lasting performance. Key Features Excellent resistance to chlorinated water and common pool chemicals Movement accommodation of ± 25 % Neutral cure — non-corrosive, safe on most metals and tile systems High elasticity and recovery Very good resistance to fungal attack Suitable for interior and exterior applications Typical Applications Underwater joints in swimming pools Wet areas, such as spas, splash zones, and shower recesses Sealing between tiles, concrete, glass, and metal substrates Technical Highlights Service temperature range: –40 °C to +80 °C Shore A hardness (28 days): ~20 Elastic recovery: > 90% Typical curing speed: ~2 mm per 24 h Skinning time: ~5 minutes (23 °C / 50% RH) Available in White, Grey, and Transparent shades Shelf life: 15 months (when stored unopened between 5 °C and 25 °C) Usage & Application Tips Ensure surfaces are clean, dry, and free from contaminants (oil, dust, grease). Roughen smooth, non-porous surfaces (e.g. metal, glazed tile) before application. Use appropriate primers (e.g. Sika Aktivator-205, Primer-3 N) on metals, PVC, or porous substrates as recommended. Apply a closed-cell foam backing rod to control joint depth. Insert sealant by cartridge gun, avoiding air entrapment. Tool the bead within the skin formation time. Allow full cure (minimum 7 days) before filling pool with water. Limitations & Precautions This product is not suitable for: Joints in direct contact with potable food or drink Overpainting Use on substrates that leach oils, plasticisers or solvents (e.g. bitumen, EPDM rubber) Always consult the current Product Data Sheet (PDS) and Safety Data Sheet (SDS) for full technical, safety, and application details before use.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $24.50 $0.08/ml

  • Sika Sikasil Pool Silicone Water Resistance [Transparent]

    Sika Sika Sikasil Pool Silicone Water Resistance [Transparent]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $25.50

  • Selleys No More Gaps Multipurpose Sealant Filler 150g [White]

    Selleys Selleys No More Gaps Multipurpose Sealant Filler 150g [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 300% elongation/stretch and up to +/- 15% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage. Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application). Is formulated for long term resistance to cracking and crumbling. Easy water clean-up Will not stain building materials. Has good resistance to weathering. Low toxic, low odour, low VOC, less harmful to the environment Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles which are not exposed to water In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm  What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Paint Many other building materials

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $8.00

  • Selleys Glass Clear Sealant Adhesive Windows and Aquariums 75g

    Selleys Selleys Glass Clear Sealant Adhesive Windows and Aquariums 75g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Glass Silicone is an acetic acid curing 100% silicone, which has excellent adhesion to glass and has been specially formulated for glazing and aquarium construction. Features The acetic curing formulation results in superior adhesion on glass and glazing surfaces. Superior silicone formulation forms a durable seal and which does not shrink when drying. UV and weather resistant remaining flexible, not shrinking, crumbling, cracking or drying out. Temperature resistance – approximately -60°C +150°C Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. 25-year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Clear Appearance Smooth Where can this product be used? Windows Glass aquariums Perfect for use on or around: Windows Windows Frames Glass Aquariums Repairs gaskets in dryers, ovens, refrigerators and washing machines. Repairs rips in awnings. Will not adhere to concrete, cement products, zinc or copper containing metals, marble, limestone or lead. Can not be painted over. Not suitable for use on oily woods such as cypress, teak or cedar. Not suitable for use on roofs and gutters as it will cause corrosion. Use SELLEYS Roof and Gutter Silicone. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Stainless Steel Many plastics including polystyrene Most woods Rubber/ canvas Glazed ceramics & porcelain How to use this product Thoroughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow drying completely before applying silicone. If there is old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenious product makes removing old silicone easy. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. For aquariums, allow the product to fully cure for 7 days. Prior to usage, thoroughly wash out with water, drain and refill before introducing fish. Suitable for constructing and repairing small aquariums. The specialist design required for large tanks. Contact SELLEYS if unsure. Handy tips Tips for Using a Silicone Sealant on Glass Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. The depth of the sealant should be no more than 10mm in joints. To fill larger joints use a suitable backing rod (such as closed cell polyethylene foam or similar), leaving the gap depth no larger than half the width of the joint. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as product releases acetic acid while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of the product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $17.00

  • Polyfilla F20 Gap Filler - High Flexibility, Superior Durability & Smooth Finish for Interior & Exterior Gaps with Up to 20% Joint Movement

    Poly Polyfilla F20 Gap Filler - High Flexibility, Superior Durability & Smooth Finish for Interior & Exterior Gaps with Up to 20% Joint Movement

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Polyfilla F20 Gap Filler: The Ultimate Gap Solution for High-Stress Applications Features Highly Durable High Flexibility Smooth Finish +/- 20% Joint Movement Capability Product Description Polyfilla F20 Gap Filler has been specially formulated to offer superior flexibility in high-stress interior and exterior applications. With up to +/- 20% joint movement capability, this gap filler is ideal for filling gaps around cornices, wall joints, skirting boards, as well as window and door frames. Application This product is extremely easy to use. Simply ensure the area is clean and dry, apply the filler, and allow it to dry. It adheres well to multiple surfaces and offers long-lasting results. Use Cases Cornices Wall Joints Skirting Boards Window & Door Frames

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $8.10

  • Poly Gap Filler Sealant Multipurpose [White]

    Poly Poly Gap Filler Sealant Multipurpose [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A flexible multipurpose gap filler, to fill gaps around cornice, wall joints, skirting board, window and door frames where where movement causes ordinary fillers to crack or fall out. For use on: Wood, brick, aluminium, glass, plasterboard, ceramic tiles and painted surfaces (INTERIOR & EXTERIOR) Coverage: 30m/3mm bead. Dry time: Skins in 30 minutes at 25°C. Full cure in 7days. Ready to use: YES Available in: 475g Colour: White NOTE: Not for fine joints between tongue and groove boards or weatherboard overlaps. • Ensure surfaces are clean, dry and free from oil, dust, grease, flaking paint and old sealant. • Using caulking gun, push sealant ahead of nozzle forcing it onto the surface and into the joint. Ensure the sealant is touching both sides of the gap. • Smooth with wet finger or knife and remove excess sealant immediately with a damp cloth. • Allow sealant to skin approx 30 min before painting with water-based paints. • Allow to set for 48 hours if using oil based paint or if joint is large. • Some water-based undercoats and flat paints may crack on drying. Test a small section of sealant. Paint cracking may be reduced by using a vinyl/ acrylic semi glossed paint or oil based undercoats first, or by allowing the sealant to cure thoroughly before painting. • Do not use outside if rain is imminent, not for contantly damp areas. • Painting improves exterior durability. • Use Poly silicone sealants for a watertight seal or where movement is excessive. • Water clean up Q. How do I fill gaps between my wooden window frames and inside wall? A. You're dealing with two different materials here, plaster and wood. To allow for differential movement between them, use Polyfilla Gap Filler, wiping off any excess with a damp cloth. Q. I painted over the areas where I used Polyfilla Gap Filler and now cracks have appeared. Why has this happened? A. If the gap filler was not cured sufficiently before it was painted over, cracks can occur as the gap filler shrinks. To prevent this, allow 48 hours drying time when you are filling large gaps or painting with oil-based paints. Also, some water based undercoats and paints shrink during drying and as Polyfilla Gap Filler is flexible, it won't stop cracks appearing in the shrinking paint on its surface. Test the paint on a small section of gap filler and if this is a problem you can reduce cracking by allowing the filler to cure thoroughly or by first coating it with a vinyl/acrylic semi-gloss or oil-based undercoat. Q. Why does my gap filler keeps cracking? A. It is important to remember that the width of a gap affects how much the product can move. Fine cracks less than 2mm allow the gap filler to move only very tiny amounts before it may crack again. It is best to ensure that you have at least 3mm worth of product so you can maximise the movement capability of your joint.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $5.00

  • Parfix Roof Gutter Concrete Silicone Sealant [Black]

    Parfix Parfix Roof Gutter Concrete Silicone Sealant [Black]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $9.35

  • Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]

    Bostik Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $22.51

  • Bostik Seal it Kitchen & Bathroom Light Grey: The Ultimate Neutral Cure Sealant for Wet Areas—Resists Mold & Mildew, UV Resistant, Low Odour

    Bostik Bostik Seal it Kitchen & Bathroom Light Grey: The Ultimate Neutral Cure Sealant for Wet Areas—Resists Mold & Mildew, UV Resistant, Low Odour

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Bostik Seal it Kitchen & Bathroom Light Grey: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $15.35

  • Selleys 475g No More Gaps Interior Multipurpose Gap Filler - 3 Pack

    Selleys Selleys 475g No More Gaps Interior Multipurpose Gap Filler - 3 Pack

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 300% elongation/stretch and up to +/- 15% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage. Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application). Is formulated for long term resistance to cracking and crumbling. Easy water clean-up Will not stain building materials. Has good resistance to weathering. Low toxic, low odour, low VOC, less harmful to the environment Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles which are not exposed to water In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm  What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Paint Many other building materials

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $15.50

  • Packshot of Selleys 635 Clear Multipurpose Sealant 290ml

    Selleys Selleys 635 Clear Multipurpose Sealant 290ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys 635 Multipurpose Elastic Sealant Clear 290 mL Selleys 635 is a premium 100 percent clear elastic joint sealant that delivers strong, flexible and waterproof seals for indoor and outdoor jobs. Powered by hybrid technology, it adheres to most common building materials without primer and resists UV and weather for long lasting performance. Paintable with water based paints after skinning. Why you will love it Crystal clear finish that stays clear Excellent weather and UV resistance for exterior use Primerless adhesion to most surfaces Adheres to damp or wet surfaces Non slumping in joints up to 20 mm Low odour and low VOC, solvent and isocyanate free Paintable with water based paints once skinned Where to use Vertical and horizontal joints on most indoor and outdoor surfaces, including concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles, glass and many other common building materials. Not suitable for Polyethylene, Polypropylene or PTFE, structural glazing, or permanent water immersion. Directions Prep Clean and remove dust, grease and contaminants. Degrease metals. Cut nozzle on a sharp angle slightly wider than the joint. Use a suitable backing rod to control depth where required. Apply Gun the sealant into the joint. Tool within 10 minutes to ensure good contact with joint sides. Paint When skinned, paint with water based paints. For solvent based paints, first apply a water based undercoat and test on a small area. Clean up Clean spills and tools with mineral turps before cure. Once cured, remove mechanically. Storage Store below 30°C in a cool, dry place Unopened shelf life 12 months from date of manufacture Technical details Technology Moisture curing silyl modified polymer Colour Clear Packaging Cartridge 290 mL Density Approx. 1.05 g per mL Skin time at 23°C and 50 percent RH About 45 minutes Tack free time at 23°C and 50 percent RH About 60 minutes Cure rate at 23°C and 50 percent RH 2.5 to 3.5 mm per 24 hours Shore A hardness 35 ± 5 Tensile strength 1.7 MPa Elongation at break 240 percent Movement capability ± 12.5 percent Application temperature 5 to 35°C Service temperature ?20 to 70°C VOC content Approx. 35 g per L VOC classification Meets Green Building Council of Australia limits for general purpose and architectural sealants Good to know Better extrudability and curing from 5°C and above Non bubbling and non slumping formulation Sandable when fully cured Limitations Not for permanent water immersion Not for Polyethylene, Polypropylene or PTFE Not for structural glazing Follow all safety directions. For first aid and handling information refer to the product SDS.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $20.74

  • Packshot of Bastion Bond Breaker Joint Sealant 300ml

    Bastion Bastion Bond Breaker Joint Sealant 300ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Bastion Bond Breaker Joint Sealant Professional silicone bond breaker for wet areas. Create a flexible, waterproof separation at wall to wall and wall to floor junctions so your membrane and tile system can move without cracking. Ideal for bathrooms, showers, laundries and balconies. Why choose this sealant Permanently flexible to absorb movement in corners and junctions Neutral cure silicone suitable for use with most waterproofing membranes Low odour, low VOC, indoor use friendly Excellent adhesion to common building materials including concrete, masonry, ceramic tile, porcelain and most metals Water resistant once cured and designed for wet area applications Easy to gun out and tool for a smooth finish Typical uses Forming a bond breaker fillet in shower bases, bathrooms and laundries before waterproofing Movement joints at internal corners prior to tiling General wet area sealing where a flexible joint is needed Surface preparation Ensure surfaces are clean, dry and free from dust, oil, loose material and old sealant. Mask adjacent edges for a neat finish if required. For wide gaps, insert backing rod to control sealant depth. How to apply Cut the cartridge nozzle to the desired bead size and load into a standard caulking gun. Gun a continuous bead into the corner or joint. Aim for a smooth cove fillet in the 5 to 12 mm range. Tool the bead with a spatula or rounded tool to compact and shape it. Remove masking tape while the sealant is still wet. Allow the bond breaker to skin before applying compatible waterproofing membranes over the area. Follow your membrane manufacturer’s recoat time. Cure and finishing Skin time is typically minutes depending on temperature and humidity. Full cure occurs over 24 to 48 hours for standard beads. Thicker sections require longer. After the membrane has cured, complete tiling and finish perimeter joints with a sanitary grade silicone. Clean up Wipe away excess immediately with a clean cloth. Once cured, remove mechanically by trimming and peeling. Handy tips Not paintable. If painting is required, paint adjacent surfaces before sealing. Always use backing rod for large joints to control sealant depth and reduce three sided adhesion. Pre test on sensitive or natural stone surfaces. Do not use in continuously immersed conditions or for structural glazing. Storage and packaging Cartridge size: 300 mL Store upright in a cool, dry place. Use before the best by date printed on the cartridge. Safety Use in a well ventilated area. Avoid contact with skin and eyes. Keep out of reach of children. Refer to the product label for first aid directions. In the box 1 x 300 mL cartridge of Bastion Bond Breaker Joint Sealant 1 x application nozzle

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $10.85

  • Packshot of Dunlop FC Polyurethane Flexible Joint Sealant 300ml

    Dunlop Dunlop FC Polyurethane Flexible Joint Sealant 300ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop FC Joint Sealant Dunlop FC Joint Sealant is a premium, ultra flexible, moisture curing polyurethane sealant designed for jointing fibre cement, blueboard and compressed fibre cement sheets. The non slump formula handles joints up to 40 mm wide with a movement capability of plus or minus 25 percent. It is easy to apply, solvent free and isocyanate free. Colour: Grey. Why choose this sealant High flexibility for dynamic joints Non slump for clean, accurate beads on vertical and horizontal surfaces Solvent free and isocyanate free Paintable after curing Reliable performance supported by a 10 year guarantee Ideal uses Joints in fibre cement, blueboard and compressed fibre cement sheets Facade and cladding joints where movement is expected General building joints up to 40 mm width Compatible surfaces Adheres to most common construction substrates, including: Fibre cement sheets and blueboard Precast concrete panels, blockwork and bricks Sandstone and granite Fibreglass Plasterboard Technical details Movement capability ± 25% Joint width Up to 40 mm Skin time Approximately 35 minutes at 23°C and 50% RH Tack free time Approximately 1 hour at 23°C and 50% RH Cure rate About 2.5 mm per 24 hours at 23°C and 50% RH Application temperature 10°C to 35°C Clean up Warm water immediately after use Shelf life 12 months unopened, stored cool and dry Finish Paintable when dry. Can be overcoated with paint or texture coats. Colour Grey Surface preparation Ensure surfaces are clean and dry, free of dust, oil, grease, salt, mould, release agents and any contaminants that may affect adhesion. Mask adjacent areas to keep lines neat. Follow sheet fixing instructions from the board manufacturer. How to apply Cut the nozzle at a sharp angle slightly wider than the desired bead or joint width. Use a suitable backing rod where required to control depth. Aim for a joint depth equal to half the joint width. Gun the sealant into the joint and tool within 10 minutes using a round spatula to ensure full contact with the joint sides. Curing times increase in cold or humid conditions. Safety and handling Avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection. Ensure adequate ventilation during application. Keep out of reach of children. Refer to the product SDS for full safety guidance. Guarantee Backed by a 10 year guarantee when used as directed.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $21.58

  • Packshot of CPC Shower Plug Waterproofing Sealant 220ml

    CPC CPC Shower Plug Waterproofing Sealant 220ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Shower Plug Penetrating Sealer 220mL Stop leaks without removing tiles. Shower Plug penetrates into masonry surfaces and forms a water repellent barrier that fixes and prevents leaks in showers, balconies and other masonry areas. One application lasts 10 years. Penetrates grout, tile and masonry to block water at the source No tile removal required Indoor and outdoor use, friction and UV resistant Does not change surface appearance or make it slippery Makes surfaces easier to clean and helps prevent mould Breathable seal allows trapped moisture below tiles to escape Seals gaps up to 1 mm. For wider cracks, repair with grout or silicone first Why Shower Plug Released in 1992, Shower Plug is the original Australian penetrating sealer technology for leaking shower repair. It delivers cost and time efficiency with proven longevity and reliability. Fixing a leaking shower, methods compared Item Tile and membrane removal and replacement Shower Plug 220mL Typical cost > $1000 $55 Time required > 5 days 30 minute application, ready to use in 12 hours Skill level Trade DIY Effective lifespan Average 5 years 10 years minimum Coverage Approx. 7 m² per pack (about 75 ft²), depending on porosity. Where to use Grout Tiles including ceramic, porcelain, marble, glazed or unglazed, terrazzo, slate, terracotta and more Concrete and masonry Bare plaster. If painting later, use a solvent primer undercoat after treatment Showers, balconies, other tiled or masonry wet areas Not suitable for Plastics and polymers such as polyurethane and polycarbonate Glass Metal Wood Painted surfaces How to apply Ensure the surface is clean and dry. Using a natural bristle brush, apply the first coat evenly. After 5 minutes, apply a second coat. Five minutes after the second coat, wipe away any remaining excess from the surface. Allow to cure. Area is ready to use in 12 hours. Important: Wipe the final coat off within 5 minutes. If left to dry on the surface, a white residue may appear. Remove any residue with turpentine. Good to know Gives off a mild solvent type odour during application and cure. This fades by the end of curing. Does not affect clothing under normal use. Safer to handle than household paint when used as directed. Always use protective gear and ventilation. Specifications SKU SP220ML Category Shower Plug Pack size 220 mL Coverage Up to 7 m² per pack Weight 0.25 kg Dimensions 7.5 cm x 7.5 cm x 8 cm Finish Invisible. No change to surface look or feel Use areas Showers, balconies, tiled and masonry wet areas Lifespan 10 years Directions recap Two coats applied 5 minutes apart. Wipe off excess 5 minutes after second coat. Ready to use in 12 hours. What you get Shower Plug 220 mL bottle Simple step by step instructions Shower Plug gives you the solution.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $61.69

  • Packshot of Selleys Roof & Gutter Silicone Sealant Translucent 310g (3 Pack)

    Selleys Selleys Roof & Gutter Silicone Sealant Translucent 310g (3 Pack)

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $46.22

  • Packshot of Selleys Wet Area Waterproof Silicone Sealant White 300g (3 Pack)

    Selleys Selleys Wet Area Waterproof Silicone Sealant White 300g (3 Pack)

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. Safety Tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $47.44

  • Packshot of Crommelin Hybrid MS Polyurethane Flexible Sealant 300ml

    Crommelin Crommelin Hybrid MS Polyurethane Flexible Sealant 300ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Crommelin Hybrid MS Polyurethane Flexible Sealant 300ml Take on interior and exterior sealing with a professional grade hybrid MS polyurethane. This single component sealant delivers a flexible, durable seal on common building substrates and is suitable for a wide range of construction and maintenance tasks. Key benefits Very low VOC and isocyanate free UV resistant for long term outdoor performance High flexibility to accommodate joint movement Excellent adhesion on properly prepared porous and non porous surfaces Easy to gun, tool and clean up Typical applications Construction and expansion joints Perimeter sealing around windows and doors Roofing and cladding laps, flashings and penetrations General gap sealing in wet and dry areas Suitable substrates Concrete, masonry, brick and render Timber and fibre cement Metals and coated metals Many plastics* and glass *Always pre test for compatibility and adhesion. Surface preparation Surfaces must be clean, dry, sound and free of dust, oil, release agents and loose material. Remove old sealant and contaminants. Abrade dense or glossy surfaces if required. Use suitable primer if specified for difficult or highly porous substrates. Mask edges for neat joints and install closed cell backing rod where needed to control joint depth. Application Cut nozzle to required bead size and load cartridge into a quality caulking gun. Gun a continuous bead into the joint ensuring full contact with sides and backing. Tool off with a moistened spatula for a smooth finish before skin forms. Protect from water and disturbance during initial cure. Clean up Clean tools and fresh spills promptly. Once cured, remove by mechanical means. Good to know Low odour formulation suitable for indoor use with ventilation. Paintable with many water based coatings once skinned and cured. Always test first. Store upright in a cool, dry place. Keep out of direct sunlight. Safety Wear suitable gloves and eye protection. Avoid contact with skin and eyes. If contact occurs, rinse with clean water. Refer to the product Safety Data Sheet for full precautions. What’s in the box 1 x 300ml cartridge 1 x application nozzle

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $15.15

  • Packshot of Aftek MDF Adhesive 250ml

    Aftek Aftek MDF Adhesive 250ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Aftek MDF Adhesive 250 ml Overview Aftek MDF Adhesive 250 ml is a high quality fast setting MDF adhesive set designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials MDF timber trims decorative profiles Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Use in ventilated areas between 10°C and 30°C. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Activator accelerates set in seconds to minutes. Full strength develops over several hours. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Remove overspray and uncured adhesive with suitable solvent. Use carefully to avoid staining. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $8.37

  • Bostik General Purpose Neutral Cure Silicone Sealant 20ml – Clear, Flexible & Waterproof Bostik General Purpose Neutral Cure Silicone Sealant 20ml – Clear, Flexible & Waterproof

    Bostik Bostik General Purpose Neutral Cure Silicone Sealant 20ml – Clear, Flexible & Waterproof

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Overview This high-quality general-purpose silicone sealant is a versatile solution for a wide range of sealing and bonding applications. Engineered with neutral cure technology, it is designed to provide a durable, flexible, and weather-resistant seal that remains reliable even in demanding environments. Once cured, the sealant forms a strong rubber-like finish that is permanently elastic, ensuring long-lasting performance both indoors and outdoors. Key Features Neutral Cure Technology: Low-odor curing system suitable for sensitive applications. Permanently Flexible: Retains elasticity over time without cracking or shrinking. Waterproof Protection: Provides a watertight seal, protecting against leaks and moisture ingress. Interior & Exterior Use: Unaffected by rain, snow, extreme temperatures, or prolonged UV exposure. Excellent Adhesion: Bonds strongly to most common building materials without primer. Easy Application: Smooth flow from the tube, easy to tool and clean before curing. Applications This sealant is designed for general-purpose use across a variety of materials and environments. Its flexibility and adhesion make it suitable for: Sealing around window and door frames. Lap joints in metal guttering and roofing sheets. Bonding panels such as wood, plasterboard, insulation board, and drywall. Fixing masonry joints including sills, brickwork, and decorative trims. Gap filling around pipes, conduits, and penetration surfaces. General sealing in kitchens, bathrooms, and living areas where flexibility is required. Limitations Not suitable for permanent water immersion (e.g., underwater joints or continuous water load). Not recommended for use on polyethylene (PE), polypropylene (PP), polycarbonate (PC), polymethyl methacrylate (PMMA), PTFE, neoprene, bituminous surfaces, or very soft plastics. Not intended for deep cavity filling without adequate moisture for curing. Surface Preparation To ensure maximum performance, surfaces must be clean, dry, and free from dust, grease, or loose particles. Non-porous surfaces should be wiped with solvent and dried with a clean cloth. Porous surfaces should be lightly abraded or brushed to remove contaminants and improve adhesion. Complete any painting work before applying the sealant. Application Instructions Remove the cap and pierce the nozzle seal. Apply steadily along the joint or surface, ensuring continuous contact. Smooth or tool the bead before skin formation occurs. If masking tape is used, remove immediately after tooling to avoid tearing the cured seal. Curing At room temperature (23°C), the sealant will skin over within 15 minutes and achieve full cure within 24 hours, depending on humidity and joint depth. Once cured, it provides a permanently flexible and weatherproof joint. Cleaning & Maintenance Excess uncured sealant can be cleaned using a cloth dampened with mineral turpentine. Fully cured material should be trimmed away carefully with a sharp blade. Store unused tubes in a cool, dry place below 25°C and away from direct sunlight. Shelf life is up to 12 months from the date of manufacture. Health & Safety Use in a well-ventilated area. Avoid contact with eyes and mucous membranes, as uncured sealant may cause irritation. In case of contact with eyes, flush thoroughly with water and seek medical advice. Keep out of reach of children. Always follow safety instructions and refer to the product’s safety data for detailed guidance. Why Choose This General Purpose Silicone Sealant? This sealant is a trusted choice for tradespeople, DIY enthusiasts, and homeowners seeking a reliable solution for everyday sealing needs. Its combination of flexibility, adhesion, and weather resistance ensures that once applied, it continues to protect and bond effectively for years to come. Whether you are fixing a leaking gutter, sealing around windows, or bonding decorative trims, this product provides professional results with minimal effort. Technical Specifications Technology Neutral Cure Silicone Appearance Clear Paste Working Time Up to 15 minutes Tack-Free Time Approximately 15 minutes Full Cure at 23°C 24 hours Flexibility Permanently elastic after curing Weather Resistance Unaffected by rain, snow, UV, and temperature variations Applications Windows, doors, guttering, masonry, panels, pipes, decorative elements Storage Below 25°C, out of direct sunlight Shelf Life 12 months from manufacturing date

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $9.98

  • Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml [White]

    Sika Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $0.00 - $28.00

  • Sika Sikaflex Pro+ Sealant 310ml [White]

    Sika Sika Sikaflex Pro+ Sealant 310ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $24.00

  • Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Clear] Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g

    Selleys Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. Safety Tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $0.00 - $16.00

  • Selleys Solar Flex UV Protection High Performance Sealant 445g [Black] Selleys Solar Flex UV Protection High Performance Sealant 445g [Clear]

    Selleys Selleys Solar Flex UV Protection High Performance Sealant 445g

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys SolarFlex Selleys SolarFlex provides protection from ultraviolet (UV) radiation and other harsh weather elements. Harsh Australian and New Zealand conditions make the choice of an effective solar/weather protection solution critical. Features Superior weather protection Long-lasting flexibility No primer required before painting Watertight seal with a 10-year guarantee* Adhesion to wet or damp surfaces Non-bubbling Better curing and extrudability (>5°C) with no slump Paintable with water-based paints after product skins in 60 to 90 minutes Low VOC** Where can this product be used? Skylights Walls Patios Floors Fencing Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics* *Not suitable on polyethylene, polypropylene, or Teflon. Application Instructions Ensure substrates are clean and free of oil, grease, or loose particles. Cut the seal and nozzle, then fit it to the cartridge and place it in the caulking gun. Hold the caulking gun at a 45° angle and gun the sealant ahead of the nozzle, ensuring the product is pushed into the joint. For neat joints, use masking tape on both sides of the joint and remove it before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g., polyethylene backer rod) and appropriate joint width/depth. See the technical datasheet for more information. Limitations Not suitable on polyethylene, polypropylene, or Teflon. Cure excess product before disposal. Not for permanent water immersion or below water-line use. For water immersion, please use Selleys Marine Flex.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $23.92

  • Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Black] Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g

    Selleys Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $0.00 - $17.00

  • Sikaseal Kitchen and Bathroom Silicone Sealant Sanitary Grade 300ml Alabaster Sikaseal Kitchen and Bathroom Silicone Sealant Sanitary Grade 300ml Almond Ivory

    Sika Sikaseal Kitchen and Bathroom Silicone Sealant Sanitary Grade 300ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    SikaSeal® Kitchen and Bathroom SikaSeal® Kitchen and Bathroom is a one-component, neutral-curing, low-odour silicone sealant with excellent adhesion and a long shelf life for DIY applications. It cures at room temperature under the action of atmospheric moisture to give a permanently flexible silicone rubber. Uses Glass and enamel Ceramics and tiles Aluminium, steel, zinc, copper Plastic laminates Rubber Stainless steel Concrete and grouts Characteristics / Advantages Excellent adhesion Great weatherability Non-sag Great tooling characteristics Long-term mould resistance Interior and exterior usage Fast curing Colours White Beige Black Charcoal Transparent Alabaster Almond Ivory Off White Stone Pewter Grey Mid Grey Stone Brown Packaging 300ml cartridges, 12 cartridges per box Shelf Life 12 months from the date of production if stored in undamaged and unopened original sealed containers, in dry conditions, and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base: Neutral curing Density: 0.98 g/cm³ @ 23ºC Skin/Forming Time: 10-15 minutes @ 23ºC/50% r.h. Curing Rate: 72 hours @ 23ºC/50% r.h. Consistency: Non-sag Mechanical/Physical Properties Tensile Strength: 0.4 N/mm² @ 23ºC/50% r.h. Shore A Hardness: 20 SHA E-Modulus: 0.30 N/mm² at 10% elongation @ 23ºC/50% r.h. Ultimate Elongation: 300% Anti-mildew Property: 0 level

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $0.00 - $14.00

  • Last stock! MaxisiL A Silicone Sealant [Colour: A28 Brown] MaxisiL A Silicone Sealant [Colour: A29 Havana]

    MaxisiL MaxisiL A Silicone Sealant Wet Area Sealant

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    The Premium Wet Area Sealant Wet areas Baths, showers, toilets Easy to use Contains strong fungicides to fight mould Maxisil A Ceramic Silicone is an acetic cure silicone recommended for all ceramic tile areas, especially for expansion joints in bathrooms, kitchens, and flooring sectors. Built-in fungicides for mould resistance For both exterior and interior use Excellent weatherability, resistant to ageing and UV radiation Resistant to chemicals and temperature Primerless adhesion to clean, dry surfaces such as ceramics, glass, acrylics, aluminium, and painted wood Very good tooling and smoothing properties Time-saving with an easy cleanup system Please note that colour samples are not true to the actual colour. This is a guide only. Characteristics 1-component acetate-curing silicone sealant Excellent weathering, ageing, and UV resistance Enables a great finish, will not string during application Good tooling and smoothing properties Contains fungicides Medium skin formation time for easy handling Very good adhesion on ceramic substrates Primerless adhesion to many substrates Stress expansion modulus at 100% (DIN 53 504, S3A): 0.3 N/mm² Meets DIN 18545, part 2D (German industrial standard) Available in a variety of colours (custom colours available upon request) Fields of Application Sealing connection joints between ceramic tiles, showers, baths, and flooring sections Expansion/movement joints in bathrooms and wet areas Connection joints on door and window frames Sealing double-glazing joints Glass block glazing Sealing general building substrates Suitable for interior and exterior use Important Information Before application, ensure materials in the contact area are compatible with the sealant and with each other to prevent damage or discoloration. If in doubt, consult the manufacturers of surrounding substrates. While curing, small amounts of acetic acid are released — ensure good ventilation After curing, the product is odourless and harmless Thicker silicone layers require longer vulcanisation time Not for full-surface bonding unless construction prerequisites are met For layers over 15mm, contact our technical department Avoid contact with bitumen-containing materials or those releasing solvents (e.g. butyl, EPDM, neoprene, bituminous paints) When replacing mould-contaminated joints, remove all old sealant and treat areas with Maxisil Anti-Mildew Spray Technical Properties Skin-forming time (23°C / 50% RAH) ~ 15 min Curing in 24h (23°C / 50% RAH) ~ 2–3 mm Processing temperature +5°C to +35°C Viscosity (23°C) Pasty, stable Density (23°C, ISO 1183-1) ~ 1.0 g/cm³ Shore A hardness (ISO 868) ~ 20 Permissible movement capability —

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $22.50

  • Weldbond Steel Tough Welbond Universal Adhesive Tube 60ml

    Weldbond Weldbond Steel Tough Welbond Universal Adhesive Tube 60ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications. Same formula & product you trust, just better looking! Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable. Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age. It is non-toxic, non-flammable & Solvent free 3-4 times stronger than standard P.V. High Solid content (51-53%) means more glue and it goes a lot further Does everything a P.V.A does, plus more Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $8.13

  • Weldbond Steel Tough Welbond Universal Adhesive Tube 3Lt

    Weldbond Weldbond Steel Tough Welbond Universal Adhesive Tube 3Lt

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications. Same formula & product you trust, just better looking! Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable. Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age. It is non-toxic, non-flammable & Solvent free 3-4 times stronger than standard P.V. High Solid content (51-53%) means more glue and it goes a lot further Does everything a P.V.A does, plus more Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $103.00

  • SikaSeal Appliance Silicone Sealant Thermal Seal 300g Black

    Sika SikaSeal Appliance Silicone Sealant Thermal Seal 300g Black

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Premium one component room temperature vulcanising silicone sealant USE Fridge and freezer sealing Pizza oven sealing Oven sealing Aluminium Glass CHARACTERISTICS AND ADVANTAGES High temperature resistance (-50 to 250OC) Excellent adhesion Gap filling properties Heat proof Vibration resistant Highly versatile PACKAGING: 300 ml cartridges COLOUR: Black SikaSeal® Appliance Silicone Sealant is a premium one component room temperature vulcanising (RTV) silicone rubber designed for flexible gasketing and sealing applications. SikaSeal® Appliance Silicone Sealant forms a tough but flexible seal of all shapes and sizes and fills any surface voids. The cured product can withstand vibration, weathering, temperature extremes, water oil and grease without hardening, shrinking or cracking. Uses  Fridge and freezer sealing  Pizza oven sealing  Oven sealing  Aluminium  Glass Characteristics / Advantages  High temperature resistance (-50 - 250°C)  Excellent adhesion  Heat proof  Gap Filling properties  Vibration resistant  Highly versatile Product Data Colour Black Packaging 300ml Cartridge, 12 cartridges per box Storage 18 months from date of production if stored in undamaged and unopened original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base 1-C silicone Density (uncured) 1.0 kg/l approx. Skin Time 10 min approx. Tack-free time 20 min approx. Curing Time 24 hours approx. Cure Mechanism Moisture-curing Cure Type Acetoxy Application temperature 5 - 45°C Mechanical/Physical Properties Tensile Strength 1.0 N/mm2 approx. Shore a Hardness 25 approx. Ultimate Elongation 600% approx. Application Details Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue-free solvent and allowing drying properly. Cut the nozzle at a 45° angle to the desired bead size (3 mm is suitable for most applications) then apply a continuous and even bead along the joint. Cure Mechanism SikaSeal® Appliance cures by reaction with atmospheric moisture. The reaction thus starts at the surface and proceeds to the core of the joint. The curing speed depends on the relative humidity, temperature and thickness of the sealant. At low temperatures, the water content of the air is lower and the curing reaction proceeds more slowly. Clean Up Uncured, excess SikaSeal® Appliance may be removed with Sika® Remover-208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife. Application Conditions/ Limitations Restrictions On Use SikaSeal® Appliance is not recommended for use in applications where it will be permanently exposed to temperatures exceeding 250°C or in contact with fuels. The above information is offered for general guidance only. 

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $21.37

  • Sikaflex®-111 Stick & Seal Grey: The Ultimate 1-Part Adhesive & Sealant for Internal & External Projects

    Sika Sika Sikaflex 111 Stick & Seal 1-Part Adhesive & Sealant 290ml [Grey]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $23.00

  • Sikaflex®-111 Stick & Seal Black: All-in-One Adhesive & Sealant Solution Without Surface Pre-treatment 290ml

    Sika Sika Sikaflex 111 Stick & Seal 1-Part Adhesive & Sealant 290ml [Black]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $23.00

  • Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]

    Sika Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikaflex-227 is a one-component poly­­urethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $27.48

  • SikaFlex 227 White 150ml: The One-Stop Solution for Car Body Sealing - Fast Skinning, Low Odour, Paintable & Silicone-Free

    Sika SikaFlex 227 White 150ml: The One-Stop Solution for Car Body Sealing - Fast Skinning, Low Odour, Paintable & Silicone-Free

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 5–35°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $27.72

  • SikaFlex 227 Black 150ml: The One-Stop Solution for Car Body Sealing - Fast Skinning, Low Odour, Paintable & Silicone-Free

    Sika SikaFlex 227 Black 150ml: The One-Stop Solution for Car Body Sealing - Fast Skinning, Low Odour, Paintable & Silicone-Free

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 5–35°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $27.72

  • Sika Sikasil 670 Fire Resistant Silicone Sealant [Grey]

    Sika Sika Sikasil 670 Fire Resistant Silicone Sealant [Grey]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    SIKASIL® -670 FIRE | JOINT SEALANT Fire-rated joint sealant Up to 4 hours fire resistance according to EN 1366-4 Very good resistance to weathering Easy to smooth and very good workability DESCRIPTION Sikasil®-670 Fire is a fire-rated, 1-component, moisture-curing, low-modulus elastic joint sealant. USES Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates. CHARACTERISTICS / ADVANTAGES ▪ Up to 4 hours fire resistance according to EN 1366-4 ▪ Very good resistance to weathering ▪ Movement capability of ± 35% (ASTM C 719) ▪ Easy to smooth and very good workability ▪ Good adhesion to many different substrates ▪ Neutral curing ENVIRONMENTAL INFORMATION ▪ LEED® EQc 4.1 ▪ SCAQMD, Rule 1168 ▪ BAAQMD, Reg. 8, Rule 51 APPROVALS / STANDARDS ▪ EN 15651-1 F EXT-INT CC 25 LM ▪ EN 15651-4 PW INT ▪ ISO 11600 F 25 LM & G 25 LM ▪ ASTM C 920, class 35 ▪ EN 1366-4 assessment report ▪ ETAG 026 assessment report ▪ EN 13501-2 classification report ▪ EN 140-3 ▪ EN 13501-1 class B-s2-d0 PRODUCT INFORMATION Chemical Base Neutral cure silicone Colour: Grey Storage Conditions Sikasil®-670 Fire shall be stored in dry conditions, where it is protected from direct sunlight and at temperatures between +5 °C and +25 °C. Density 1.35 kg/l approx. (ISO 1183-1) TECHNICAL INFORMATION Shore A Hardness 16 approx. (after 28 days) (ISO 868) Secant Tensile Modulus 0.30 N/mm2 approx. at 100% elongation (23 °C) (ISO 8339) 0.50 N/mm2 approx. at 100% elongation (−20 °C) Elongation at Break 650% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Movement Capability ±25% (ISO 9047) ±35% (ASTM C 719) Service Temperature −40 °C to +150 °C Joint Design The joint width must be designed to suit the joint movement required and the movement capability of the sealant. The joint width shall be ≥ 10 mm and ≤ 40 mm. The joint depth shall be ≤ 20 mm. A width to depth ratio of 2:1 must be maintained (for exceptions, see table below). Backing Material Use polyethylene foam backing rods. Sag Flow 2 mm approx. (20 mm profile, 50 °C) (ISO 7390) Ambient Air Temperature +5 °C to +40 °C, min. 3 °C above dew point temperature Substrate Temperature +5 °C to +40 °C Curing Rate 2 mm/24 hours approx. (23 °C / 50% r.h.) (CQP 049-2) Skin Time 25 minutes approx. (23 °C / 50% r.h.) (CQP 019-1) Tooling Time 20 minutes approx. (23 °C / 50% r.h.) (CQP 019-2) APPLICATION INSTRUCTIONS SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikasil®-670 Fire adheres without primers and/or activators APPLICATION METHOD / TOOLS Sikasil®-670 Fire is supplied ready to use. After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a foil pack or cartridge into the sealant gun and extrude Sikasil®-670 Fire into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikasil®-670 Fire sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. CLEANING OF TOOLS Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® TopClean T. Once cured, residual material can only be removed mechanically. FURTHER DOCUMENTS ▪ Safety Data Sheet (SDS) ▪ EN 13501-2 classification report ▪ ETAG 026 assessment report ▪ Brochure Sika Fire Protection Solutions LIMITATIONS ▪ Sikasil®-670 Fire cannot be overpainted. Colour variations may occur due to exposure to chemicals, high temperatures and/or UV-radiation (especially with the colour shade white). However, a change in colour is purely of aesthetic nature and does not adversely influence the technical performance or durability of the product. ▪ Do not use Sikasil®-670 Fire on natural stone. Do not use Sikasil®-670 Fire on bituminous substrates, natural rubber, EPDM rubber or on any building materials which might bleed oils, plasticizers or solvents that could attack the sealant. ▪ Do not use Sikasil®-670 Fire to seal joints in and around swimming pools. ▪ Do not use Sikasil®-670 Fire for joints under water pressure or for permanent water immersion. ▪ Do not expose uncured Sikasil®-670 Fire to alcohol-containing products as this may interfere with the curing reaction.  

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $22.15

  • Sika SikaSil 670 Fire Rated Silicone Sealant [Grey]

    Sika Sika SikaSil 670 Fire Rated Silicone Sealant [Grey]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Usage Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates. Advantages Up to 4 hours fire resistance according to AS 1530.4 Up to 4 hours fire resistance according to EN 1366-4 Very good resistance to weathering Movement capability of ± 35% (ASTM C 719) Easy to smooth and very good workability Good adhesion to many different substrates Neutral curing   Colour Grey

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $27.35

  • Sika SikaSeal 300 Glass & Weather Seal [Transparent]

    Sika Sika SikaSeal 300 Glass & Weather Seal [Transparent]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Usage Aluminium Composite materials Panels(ACP) Glass Metals Coated and painted metals Plastics Wood   Advantages Excellent adhesion High movement capability Weather resistant Outstanding UV resistance High strength Interior & Exterior Permanent flexibility Colour Transparent

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $18.18


You have seen 48 out of 121 products

A close-up lifestyle image showing a person applying Glues Australia Edge Sealing product to a wooden surface in a clean workshop, perfect for DIY and professional use

Seal and protect edges on panels, benchtops and laminates against moisture and wear. Choose non-sag beads for vertical edges and paint-matchable finishes where appearance matters. Use filters to refine by chemistry and flexibility. Always check the product page and TDS/SDS.

Login

Forgot your password?

Don't have an account yet?
Create account