
Fast-acting solutions for quick repairs and production tasks. Great for small parts and close-fit joints; consider gels for vertical surfaces. Use filters to refine by chemistry and set time. Always check the product page and TDS/SDS.
Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$23.00
Colours to suit almost any timberWaxstix are so easy to use and so handy for quick repairs to scratched or damaged timber. Waxstix can be coated and stained. Plus, Waxstix contain no beeswax so they will not leave any white ring marking otherwise known as the "halo effect". For most small scratches, simply rub the stick over the damaged area. For larger, deeper indentations (where TIMBERMATE water-based Woodfiller cannot be used), heat a knife blade with a flame or a soldering iron or stove lighter and fill the damaged area with hot wax. Remove excess wax by rubbing with the smooth side of sandpaper, a piece of cardboard or an old credit card. Use a cotton cloth to buff and remove excess wax.
$6.51
The unique rubber-infused gel formula allows powerful bonds that are extremely precise even on flexible materials. Ideal for porous and vertical surfaces, and strong enough to withstand extreme conditions. The gel’s high strength non-drip formula then dries transparent to form invisible bonds that give a long lasting durability that is both weather and shock-resistant. For intricate, hard to reach spots, Loctite Power Flex Gel Control features an easy grip squeeze bottle and nozzle for precise applications. Recommended on: Rubber, Leather, Wood, Metal, Porcelain, Paper, Plastic. Properties: -Rubber infused gel formula for extra strong and flexible bonds -Ideal for porous and vertical surfaces -Water resistant -Bonds in seconds -Withstands heavy loads -Dries transparent -Easy to open, self-piercing and anti-clog cap -Choice of applicators: convenient tube or easy grip control with a longer nozzle -Suitable for use on most surfaces* -Solvent-free -* Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Step by Step Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$12.50 $10.95
Why Choose Selleys Super Glue Adjustable Gel? Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes. Key Benefits: Adjustable Setting Time: Allows precise alignment before setting. Rapid Bonding: Bonds in 30 seconds for fast repairs. Versatile: Adheres to ceramics, china, metal, wood, and most plastics. Easy to Use: No mixing required, with a convenient gel formulation for clean application. Where Can This Product Be Used? Everyday household repairs on: Ceramic and China Metal and Wood Most Plastics* What Materials Is It Suitable For? Bonds a variety of porous and non-porous surfaces. Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers. How to Use Selleys Super Glue Adjustable Gel Prepare: Pierce the seal by attaching the nozzle with the cap and turning clockwise. Ensure surfaces are clean, dry, and free from dust, dirt, and grease. Apply: Apply a small amount of adhesive to the surfaces to be bonded. Press surfaces together gently and hold for several minutes to ensure sufficient bond strength. After Use: Wipe the nozzle clean with a cloth or paper. Replace the cap securely. Limitations Not suitable for use on leather, polyethylene, polypropylene, or PTFE. Will not permanently bond vessels exposed to water or dishwashers. Handy Tips for Best Results Ideal for vertical applications and slightly porous materials. Use 1 drop per cm² for optimal bonding. Sets in 30 seconds, achieving maximum bond strength in 24 hours. Clean-Up Instructions Wipe the tip of the tube with a cloth or paper after use. Replace the cap tightly to avoid drying out the product. Product Details Size: 3g Tube Colour: Clear Technology: Cyanoacrylate Recommended Use: Interior Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
$4.00
Glue Dots Flexible Hang Tabs Brand: GlueDots Make decorating effortless and worry free. Glue Dots Flexible Hang Tabs give you a fast, clean and removable way to hang balloons, banners, streamers, paper lanterns, lightweight garlands, bunting, ornaments and more. The crystal clear tabs apply in seconds, hold firmly to most smooth household and event surfaces, and remove cleanly when the party is over. Damage free: removes cleanly from most properly painted, sealed and smooth surfaces when used as directed. Instant bond: pressure sensitive adhesive grips on contact for quick setup. Crystal clear: low visual impact for a neat, professional look in photos and in person. Flexible design: engineered slot holds standard latex balloons without helium, plus tabs act as anchor points for string, ribbon or fine wire. No tools, no mess: no nails, pins, tacks or putty required. Indoor friendly: ideal for homes, venues, classrooms, offices and display windows. Why choose Flexible Hang Tabs From last minute birthday setups to polished corporate events, these tabs are your decorating shortcut. The flexible slot lets you slide in a balloon neck or thread ribbon, while the clear base keeps the focus on your décor. When it is time to pack down, the removable adhesive lets you lift and peel without gouging walls or leaving sticky residue. Versatile surfaces: painted walls, sealed plaster, varnished timber, tile, glass, metal, laminate and most smooth plastics. Looks better: clear tabs virtually disappear against most backgrounds. Saves time: decorate large areas quickly with repeatable placement. Reliable hold: grips evenly across the tab to help prevent droop. Great for Balloon walls and garlands without helium Banners, bunting and streamers across hallways or backdrops Paper lanterns, pom poms and lightweight ornaments from ceilings Classroom displays and noticeboards where pins are not allowed Retail window dressing and temporary point-of-sale displays Wedding, engagement, baby shower and seasonal décor How to use Prepare the surface: ensure it is clean, dry, smooth and free of dust, oils and cleaning sprays. Fresh paint should be fully cured. Peel and place: remove a tab from the liner, align and press firmly for several seconds to ensure full contact. Hang décor: slide a balloon neck into the slot or thread ribbon, cord or lightweight line through the tab opening. Adjust if needed: for best results, reposition immediately after placement before full bond develops. Removal and clean up To remove, gently lift a corner of the tab and peel it back slowly over itself at a low angle. If resistance is felt, pause and continue slowly. On delicate finishes, test in an inconspicuous area first. Dispose of tabs with household waste. No solvents or scraping required when used as directed. Pro tips Use multiple tabs to distribute weight across wider banners or garlands. Avoid textured, dusty, damp or porous surfaces which reduce adhesion. For ceiling applications, ensure the surface is smooth and dust free. Allow items that were stored cold to reach room temperature before use. Indoor use recommended. Prolonged exposure to moisture, heat or direct sunlight may reduce performance. Safety and care Keep out of reach of small children. Not a toy. Do not use to hang valuable, fragile or irreplaceable items. Always test on a small area of the surface if uncertain. Specifications Brand GlueDots Product name Flexible Hang Tabs Colour Clear Adhesive type Pressure sensitive, removable Finish Crystal clear, low profile Recommended use Indoor, temporary decorating and light display mounting Suitable surfaces Painted and sealed walls, sealed plaster, varnished wood, tile, glass, metal, laminate, most smooth plastics Unsuitable surfaces Textured, dusty, damp, porous, unsealed or flaking finishes Residue on removal Removes cleanly when used as directed on suitable surfaces Repositionable Yes, during initial placement Operating conditions Room temperature, dry environment Applications Balloons, streamers, banners, paper lanterns, pom poms, lightweight ornaments Tools required None Country of use Suitable for Australian homes, venues and classrooms Performance can vary with substrate, surface preparation and environmental conditions. Always follow the directions and test before full application. What you get Flexible, clear hang tabs on an easy peel liner. Pack quantities vary by selection. Choose the pack size that suits your event or display plan. Storage Store in a cool, dry place away from dust and direct sunlight. Keep in original packaging until use to protect adhesive surfaces. Plan your next event From birthdays to window displays, build cleaner backdrops and crisper lines with Glue Dots Flexible Hang Tabs. Add to cart and get decorating in minutes.
$13.00
T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other. Features Waterproof backing enhanced with R-Flex Technology™ for greater durability Can be used underwater UV resistant All-weather: withstands temperatures from -56C to 93C. WATERPROOF ADHESION Extra thick butyl-based adhesive means durable repairs, even under water. T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other. FEATURES: Waterproof backing enhanced with R-Flex Technology™ for greater durability Can be used underwater UV resistant All-weather: withstands temperatures from -56C to 93C. WATERPROOF ADHESION Extra thick butyl-based adhesive means durable repairs, even under water. R-FLEX TECHNOLOGY Durable, flexible and UV resistant backing for long lasting repairs. ALL WEATHER Waterproof and built to withstand extreme temperatures from -56C to 93C. Durable, flexible and UV resistant backing for long lasting repairs. ALL WEATHER Waterproof and built to withstand extreme temperatures from -56C to 93C.
$22.79
T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other. Features Waterproof backing enhanced with R-Flex Technology™ for greater durability Can be used underwater UV resistant All-weather: withstands temperatures from -56C to 93C. WATERPROOF ADHESION Extra thick butyl-based adhesive means durable repairs, even under water. T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other. FEATURES: Waterproof backing enhanced with R-Flex Technology™ for greater durability Can be used underwater UV resistant All-weather: withstands temperatures from -56C to 93C. WATERPROOF ADHESION Extra thick butyl-based adhesive means durable repairs, even under water. R-FLEX TECHNOLOGY Durable, flexible and UV resistant backing for long lasting repairs. ALL WEATHER Waterproof and built to withstand extreme temperatures from -56C to 93C. Durable, flexible and UV resistant backing for long lasting repairs. ALL WEATHER Waterproof and built to withstand extreme temperatures from -56C to 93C.
$39.54
Experience unmatched strength and durability with our T-Rex Ferociously Strong Tape, now available at Glues Australia. Measuring 9.14 meters in length, this tape is specifically designed to withstand the toughest situations and most demanding projects. Crafted for homeowners, craftsmen, and outdoor enthusiasts, T-Rex® Tape distinguishes itself from ordinary duct tapes with its formidable holding power. This makes it your go-to solution for enduring repairs, creative DIY projects, or any challenging task you encounter. The secret to its exceptional performance lies in its aggressive double-thick adhesive. This feature allows the tape to adhere firmly to rough, dirty surfaces in all types of weather and temperature conditions. T-Rex® Tape is more than just a tool; it's a reliable partner for both home use and professional job sites. It outlasts and outperforms regular duct tape, ensuring that your projects, big or small, are held together longer and stronger. Key Features: All-Weather Capabilities: Equipped with a waterproof backing, T-Rex® Tape stands resilient against harsh weather elements, even in the coldest temperatures. This feature makes it an ideal choice for outdoor repairs and applications. Enhanced Durability: The tape boasts a high-tensile woven scrim, contributing to its strength and long-lasting nature. Whether it’s used for heavy-duty tasks or simple fixes, the tape’s robust construction ensures it won’t give in. Superior Holding Power: With its double-thick adhesive, T-Rex® Tape grips onto rough and uneven surfaces with unparalleled strength. This makes it perfect for tasks that require a strong, reliable hold. Versatile Usage: Suitable for both indoor and outdoor environments, the tape is manufactured using UV-resistant materials. These materials prevent the tape’s adhesive from weakening under harsh UV rays, extending its lifespan. Wide Application Range: T-Rex® Tape is versatile enough to be used on a variety of surfaces, including brick, concrete, shingles, both painted and non-painted wood, and vinyl siding. This makes it a must-have in any toolbox. Heavy-Duty Construction: Made with a heavy-duty knit cloth, the tape is designed for long-lasting repairs or applications. Whether it's for a temporary fix or a permanent solution, you can count on its reliability. Usage Applications: Home repairs, including fixing broken items and sealing leaks. Crafting and DIY projects, offering creative flexibility. Outdoor applications, including camping gear repairs. Professional job site tasks, providing reliability and strength. Why Choose T-Rex® Tape? When you choose T-Rex® Tape, you're not just selecting a tape; you're choosing a commitment to excellence and reliability. Its unique composition allows it to withstand challenges that ordinary tapes can't handle. Whether you're a professional tradesperson or a DIY enthusiast, T-Rex® Tape is the perfect addition to your toolkit, providing a strong, durable solution for any project. In conclusion, T-Rex® Tape is not just tape; it's a symbol of strength, resilience, and versatility. Its all-weather, UV-resistant features, combined with its superior adhesive strength, make it an indispensable product for anyone who values quality and reliability in their tools. Available now at Glues Australia – your trusted source for high-quality adhesive solutions.
$16.48
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
Selleys Spakfilla Rapid is a ready-mixed, lightweight filler designed for fast and easy repairs. It dries quickly, resists cracking and shrinking, and usually requires only one application—making it ideal for quick patching jobs around the home or office. Features Fills cracks and holes in a single application Pre-mixed and ready to use straight from the tub Minimal shrinkage – no need to overfill Fast drying – sand and paint within a short time Includes a convenient filling spatula Water-based formula – easy clean-up with water Paintable with both oil-based and water-based paints Where to Use Cracks and holes on stable, non-moving surfaces Walls, ceilings, doors, and window frames Small repairs in plaster, timber, and masonry surfaces Suitable Materials Wallboard and plasterboard Wood and timber surfaces Masonry and plaster Primed nail heads Product Details Colour: White Technology: Water-based Use: Interior, or exterior when painted How to Use Ensure surfaces are clean, dry, and free of dust or loose material. Using the provided spatula, press filler firmly into the crack or hole and smooth the surface. No need to overfill. Allow to dry (approximately 30 minutes for thin applications), then lightly sand for a smooth finish. Remove dust and paint as desired. For oil-based paints, allow 24 hours before painting. Limitations Not suitable for use on plastic, metal, or exterior timber exposed to moisture. Not flexible – avoid using between surfaces subject to structural movement (use Selleys No More Gaps Coloured Caulk 450g instead). Not designed for load-bearing areas or surfaces under compression (e.g. behind doors). Do not nail through filler. Avoid use below 5°C or in wet conditions. Handy Tips Wait 24 hours before painting with oil-based paints. Water-based paints can be applied once the filler has set. If filler thickens, stir before use. If too dry, add a small amount of water and mix. Clean tools with water after use. Before painting, clean with Selleys Sugar Soap Cleaner Concentrate 1L or Selleys Sugar Soap Wipes x25. For outdoor applications, protect from rain until dry and painted with two coats. Deeper repairs (over 2mm) may require longer drying times. Recommended Accessories For masking before painting: Bear Masking Tape Painter Edge Pro 48mm x 50m For reinforcing plaster joints: Eazy Tape Plasterboard Joint Tape 90m Clean Up Remove uncured product with water. Once cured, remove by scraping or sanding.
$13.00
Selleys All Clear is a multi-purpose sealant that provides long-lasting protection. All Clear is the solution to water leakage and seepage around the home. Best for : Metal, Timber, Glass, Glazed tiles, Brick, Stone, Many plastics (may damage polystyrene and polycarbonate) Features Works on wet, oily, and dirty surfaces* Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Where can this product be used? Sky lights Windows frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' enteries Sealing metal or PVC guttering and down pipes Shower screens Sinks and basins Sealing leaks in caravans and recreation vehicles What materials is this product suitable for? Metal Timber Glass Glazed tiles Brick Stone Many plastics (may damage polystyrene and polycarbonate) Use only in a well-ventilated area. Avoid contact with skin and eyes and breathing vapours. The surface must be free from dust, loose particles, and soap residue. If required, clean with turps. Porous surfaces must be dry. Cut cartridge, fit nozzle, and cut to size. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. Apply with a caulking gun, forcing product into the gap. Press into cracks or surface by pushing sealant ahead of nozzle. Smooth sealant surface immediately with tool dipped in turps. Limitations: May damage some plastics e.g. polystyrene and polycarbonate. Not for permanent water immersion e.g fish tanks Not suitable for use over silicones Not suitable for polystyrene foam *Wet Surfaces: Can be applied to clean, wet non-porous surfaces e.g. metals, glass, glazed tiles – not wet porous surfaces e.g. concrete, timber. Remove as much water as possible, preferably with acetone. Keep nozzle close to surface so sealant contacts surface immediately. Flatten immediately into joints. Adhesion improves on drying. Skins immediately, maximum toughness achieved over several days. Paintable immediately with water-based paints. For oil-based paints undercoat first with a water-based paint. Store in cool dry conditions, below 30°C
$12.00
Fast setting supa glue in a convenient bottle that allows easy, controlled and precise application. Features Easy, controlled application Non-drip glue saver nozzle, reduces waste and mess. Long fine nozzle for precise application Bonds a variety of surfaces Extremely fast setting Dries Clear for clean, neat results Water resistant No clamping necessary No mixing required Maximum strength achieved in 12 hours Only takes 45 seconds to achieve initial bond Non-clog cap Forms a rigid bond Upright self-standing bottle Comfortable to hold Where can this product be used? Ideal for small repair jobs or when immediate results are required. Water resistant not water proof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene. Leather may become hardened or discoloured For interior use only Not suitable for repairing items that are in direct contact with hot liquids Will not permanently bond glass or materials containing alkaline elements. Has no gap filling properties therefore surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Bonds a variety of porous and non-porous surfaces Metals China Rubber Leather Some plastics Wood How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Hold bottle in an upright position. Pierce seal by attaching nozzle and cap and turning clockwise. Remove cap and squeeze gently to apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. (30 seconds). The product grabs within 5-30 seconds, depending on environmental conditions and substrates to be bonded. Allow 30 minutes for sufficient bond strength for practical use. Maximum bond strength reached after 12 hours. Handy tips Cyanoacrylate adhesives can create a white residue on the surface of a substrate if the area is not well ventilated. Clean the affected area with acetone to remove residue. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. Excellent when used with other adhesives, as the temporary tack For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. Acetone (nail polish remover) or Olive oil can also be used to remove Quick Fix from skin. While superglue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Super glues cure more slowly when large amounts are used. For faster cure use sparingly. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Reseal cap in a clockwise direction. Tap bottle lightly on a flat surface to clear excess product from nozzle. To remove excess from substrates, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using thias method. Ensure cap is replaced and store in a cool dry place. Cyanoacrylate based adhesives polymerise in the presence of moisture. Store Upright. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$6.00
Single Shot, no mess just throw away Self piercing tube Bonds in 10 seconds Where can this product be used? Ideal for small repair jobs or when immediate results are required For interior projects and repairs Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or materials containing alkaline elements Has no gap filling properties, therefore, surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Metals China Rubber Leather Some plastics
$6.00
Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS Initial set 5 minutes. Curing set 15-30 minutes. Compressive strength of 2,000psi or greater in 24 hours Maximum strength in 28 days Non-toxic Volume change: Expansion after 24 hours 0.1% Contraction after 28 days 0.01% Water absorption 1.7% after 14 days Factory Production to BS 5750 Part II BONDS TO: CEMENT TIMBER MASONRY FIBREGLASS STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.
$145.00
The Loctite Super Glue Creative Pen offers the ultimate solution for precise, fast, and reliable bonding. Its ergonomic pen design ensures a controlled application, perfect for intricate tasks like crafting, DIY projects, or quick household repairs. The pen tip provides pinpoint accuracy, so you can apply just the right amount of glue, reducing mess and waste. Loctite’s fast-drying formula creates a strong bond on materials such as wood, plastic, metal, ceramic, and leather, making it versatile for any project. Whether you're fixing a broken ornament, assembling models, or working on craft projects with the kids, Loctite Super Glue Creative Pen guarantees a professional finish every time. LOCTITE® Super Glue Creative Pen Precision bonding on wood, metal, plastic, rubber, and more. Waterproof, weather-resistant, and shock-resistant. Equipped with a long nozzle and easy-grip squeeze bottle for fast and accurate application. Characteristics: LOCTITE® Super Glue Creative Pen is a one-part instant gel adhesive in a convenient dispenser, perfect for home use. It forms strong bonds between a wide range of common materials, including plastics, rubbers, metals, wood, ceramics, leather, fabrics, cardboard, and paper. Its non-drip formula allows for use on vertical or overhead surfaces. The ergonomic pack design ensures precise application, ideal for bonding smaller items. Bonding Speed: Initial adhesion in 5 to 30 seconds, depending on the substrate. Bond Strength (ISO 4587): 10 to 20 N/mm² (tensile shear) in 12 to 24 hours, depending on the substrate. Water-resistant to EN204-D3 standard. Ceramic bonds can withstand over 50 dishwasher cycles under controlled laboratory conditions. Instructions for Use: Ensure all surfaces to be bonded are clean, dry, and fit closely. Twist the cap clockwise onto the pack until you hear a clicking sound. Do not overtighten; a three-quarter turn is sufficient. Avoid skin contact with the glue. Gently squeeze the rubber panels and apply a minimal amount of adhesive to one surface. Press parts together immediately and hold with hand pressure for at least 1 minute. Allow the bond to set undisturbed for 10 minutes, or preferably overnight, to achieve full bond strength. Protect work surfaces and avoid spills. Remove cured glue with LOCTITE® Glue Remover. For best results, apply at room temperature (15-30°C) with at least 30% relative humidity. After use, wipe the nozzle clean with a tissue, replace the cap, and store in a cool, dry place. Technical Data: Composition: Ethyl cyanoacrylate Appearance: Clear gel Density: 1.1 g/cm³ @ 20°C Viscosity: Gel Safety: Refer to SDS 2669372 Shelf Life: 30 months unopened (stored at 2-8°C) Limitations: Do not use on dusty, dirty, or wet surfaces. Not suitable for bonding polypropylene, polyethylene, PTFE, silicone rubber, glass, glazed surfaces, very soft leather, or foams. Do not use for bonding items exposed to hot liquids or high temperatures for extended periods. Optimum performance is achieved in dry conditions. Storage: Store in a cool, dry place, out of reach of children. Why choose Glues Australia? We provide premium-quality adhesives like Loctite, backed by our exceptional customer service. With fast, reliable delivery across Australia, you’ll get the products you need when you need them. Shop confidently with Glues Australia, your trusted adhesive supplier!
$11.57
A rapid dual-action adhesive system is specially designed to work on plastic to form resilient, invisible bonds in seconds. Recommended on: Plastic, Porcelain, Metal, Rubber, Leather, Wood, Paper. Properties: Bonds even difficult to bond plastics such as polyethylene (PE) and polypropylene (PP) Bonds in seconds Dries transparent Easy to open, self-piercing and anti-clog cap Suitable for use on most surfaces* Solvent-free * Except Styropor®, car glass and synthetic fibres. Use: Ensure surfaces to be joined are clean, completely dry and close fitting. Using the Surface Activator like a pen apply it to both surfaces and wait 60 seconds to dry. Twist the glue cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$10.67
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$14.99
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$29.62
Crystal Clear Gorilla Tape features the adhesive strength of Gorilla Tape†, in a crystal clear tape that does not yellow outdoors. Made with a heavy duty adhesive layer and waterproof backing for extreme durability. This tape is UV and temperature resistant - great for projects and repairs both indoors and out. Crystal Clear Gorilla Tape can be applied to wet surfaces and also works under water. PRODUCT FEATURES CRYSTAL CLEAR: Non-Yellowing* HEAVY DUTY: Extra Thick Adhesive FLEXIBLE: Conforms WORKS UNDERWATER** UV, TEMPERATURE RESISTANT *Long-term extreme heat will cause product to yellow **Surfaces must be clean, smooth, non-porous, and water must be rubbed/pressed out from underneath tape. Not for use on applications under pressure or on seams. Overlapping tape may cause leaks. Crystal Clear Gorilla Tape is best if used between -12°C and 49°C. To prevent fingerprints, clean your hands prior to using the tape and handle the tape only at edge. Use a straight edge (credit card or similar object), to press out fingerprints.For best results, apply the tape to a clean surface. Airtight patches are best achieved on smooth, dry surfaces with the tape on both sides of the repair (when accessible). Tape size should be larger than the repair area, extending beyond all edges. Rub the entire surface of the tape aggressively, especially the edges. NOTE: Surface patch will gain additional strength with time. Crystal Clear Gorilla Tape works best for patching with a single layer. Not for patching inflatables at seams. WARNING: AT RISK OF BODILY HARM, DO NOT USE ON PERSONAL SAFETY DEVICES. Store the tape in the original packaging to prevent edge dirt and debris. Store it in a cool, dry place. TECHNICAL SPECS APPLICATION TEMPERATURE – -12°C to 49°C, best at room temperature SERVICE TEMPERATURE – -20°C to 60°C OUTDOOR – Yes MOISTURE RESISTANT – Yes STORAGE TIPS – Store in a cool, dry location. Store in original package to prevent edge dirt and debris. FAQS What’s the difference between Crystal Clear Gorilla Tape and other tapes? Crystal Clear Gorilla Tape is a heavy-duty, all-purpose tape that is weatherproof, air tight, crystal clear, and can be torn by hand (that’s right—no dispenser needed!). Crystal Clear Gorilla Tape is ideal for thousands of uses and sticks to almost everything—the uses are virtually endless. It can be used for patching smooth surfaces, it sticks to rough & uneven surfaces and can even be used to seal and protect surfaces. Will Crystal Clear Gorilla Tape work on plastic/vinyl/rubber? Yes, Crystal Clear Gorilla Tape should work well on these surfaces. Is Crystal Clear Gorilla Tape food safe? Crystal Clear Gorilla Tape is not recommended for direct or indirect food contact and should not be considered food safe.
$21.45
Gorilla Spray Adhesive is heavy duty, multi-purpose and easy to use. Gorilla Spray Adhesive forms a clear, permanent bond that is moisture resistant and can be used on projects both indoors and out. This spray adhesive is also photo safe. Its wide pad nozzle and controlled, fine mist spray provide an even application on the project you are working on. PRODUCT FEATURES HEAVY DUTY: Dries Permanent EASY TO USE: Repositionable CLEAR COLOR: Non-Yellowing* INDOOR & OUTDOOR: Moisture Resistant CONTROLLED SPRAY: Even Application WIDE PAD NOZZLE PHOTO SAFE All surfaces should be clean and free of dirt, grease and oil. Protect surrounding areas from overspray to avoid residual adhesive. Shake can well before using. Hold the can 15 to 20cm from surfaces to be bonded and spray an even coat of adhesive. For Maximum Bond Strength: Spray both surface to be joined. Allow to dry to tack (approximately 1 minute) and press surfaces firmly together. For Repositionable Bonds: Spray a light even coat on one surface. Allow to dry 1-3 minutes before joining. Repositionable up to 10 minutes depending on surface type, then bond becomes permanent. To remove, gently peel from corner. Tip: To avoid possible clogging, turn can away from body, turn upside down and spray a short jet of clear gas after completing the job. *Not recommended for use on vinyl materials, automotive headliners, polypropylene, polyethylene or similar materials. Do not use for bonding weighted materials. APPLICATION TEMPERATURE – 10°C to 32.2°C OUTDOOR – Yes MOISTURE RESISTANT – Yes PAINTABLE –Yes SANDABLE – Yes STAINABLE – No CURED COLOR – Clear PHOTO SAFE – Yes How do I remove Gorilla Spray Adhesive from my surface? To clean surface while adhesive is still wet/uncured, wipe adhesive off the project with a dry cloth. Isopropyl alcohol (IPA) may be used according to manufacturer’s instructions. Once cured, Gorilla Spray Adhesive may be removed using mechanical means by gently scraping surface, being careful not to damage the surface underneath. How do I remove Gorilla Spray Adhesive from body/skin? While still wet, Gorilla Spray Adhesive can be removed by wiping adhesive with a dry cloth, and then washing the area with soap and water. Once cured, rinse well with water. Is Gorilla Spray Adhesive food safe? Gorilla Spray Adhesive is not recommended for direct or indirect food contact and should not be considered food safe. What surfaces will Gorilla Spray Adhesive bond to? Gorilla Spray Adhesive is a multi-purpose product that will bond a wide variety of surfaces including fabric, paper, wood, plastic*, cardboard, foam, metal and more! NOTE: Not recommended for use on polypropylene (PP) or polyethylene (PE) plastics, vinyl, or any type of rubber with high oil or plasticizer content. Not for use on food contact surfaces. Will Gorilla Spray Adhesive bond vinyl/acrylic/rubber? Gorilla Spray Adhesive will work well on many types of plastic; however, we do not recommend for use on polypropylene (PP) or polyethylene (PE) plastics, vinyl, or any type of rubber with high oil or plasticizer content.
$26.00
Ryobi ONE+ 18V Dual Temperature Hot Glue Gun – Tool Only delivers precise and consistent adhesive application for DIY, craft, and repair projects. Designed for versatility, it features dual temperature control and cordless convenience, making it ideal for home and professional use. Key Features Dual temperature settings: Choose between 120°C for delicate materials and 160°C for stronger bonding applications. Fast heat-up time: Ready to use in approximately 3 minutes for quick, efficient work. Long nozzle design: Provides greater reach and precision when gluing hard-to-access areas. Drip tray and ergonomic handle: Keeps your workspace clean and provides comfort during extended use. LED indicator: Red light shows warming up, green light indicates ready-to-use. Part of the Ryobi ONE+ system: Compatible with all Ryobi 18V ONE+ batteries (sold separately). Specifications Voltage: 18V High Temperature Mode: 160°C Low Temperature Mode: 120°C Glue Stick Diameter: 11–12 mm Nozzle Hole: 3.0 mm Heat-Up Time: Approx. 3 minutes Weight (without battery): 0.4 kg Included Ryobi ONE+ 18V Dual Temperature Glue Gun (Tool Only) User Manual Compatible Batteries (Sold Separately) RB18L13, RB18L15, RB18L20, RB18L25, RB18L40, RB18L50, RB18L60A, RB18L90A, and more from the Ryobi ONE+ range. Safety and Maintenance Use only original accessories and spare parts. Avoid contact with hot surfaces. Do not immerse the tool or battery in liquid. Clean using a dry cloth and store with batteries removed when not in use for extended periods. Imported by Techtronic Industries Australia Pty Ltd, Mount Waverley VIC 3149.
$103.95
Make fast, tidy bonds on timber, plastics, ceramics and more with the Ozito Power X Change 18V Cordless Glue Gun. It heats up in about 120 seconds and uses standard 11 mm glue sticks, so you can tackle DIY fixes, craft projects and light repairs without cords getting in the way. Why you will love it Cordless convenience for indoor and outdoor jobs Quick heat up in about 120 seconds for less waiting Consistent flow control trigger for neat, accurate beads and dots Interchangeable nozzles round and precision tips included for detail work LED worklight helps you see the glue line clearly Auto shut off after inactivity to help conserve battery Part of Ozito PXC one battery system across tools and garden gear What is in the box Ozito PXC Cordless Glue Gun (skin only) 5 x 11 mm glue sticks Round nozzle and precision nozzle 13 mm hex spanner Ideal for Timber trims, skirting, craft and hobby builds Quick fixes on ceramics and some plastics Cardboard, fabric trims and school projects Key specifications Battery platform Ozito Power X Change 18V Pre heating time Approx. 120 seconds Max heating temperature 170°C Glue stick size 11 mm diameter Weight 0.4 kg Auto power off Yes, after inactivity Battery and charger sold separately. How to use Insert a charged PXC 18V battery and press the on or off button. Wait until the status light indicates ready, about 2 minutes. Feed an 11 mm glue stick and squeeze the trigger to apply glue. Press surfaces together straight away and hold for about 30 seconds. Stand the tool upright on the battery between uses and let it cool before storage. Good to know Use the precision nozzle for fine detail and the round nozzle for general bonding. Work on clean, dry surfaces for the best adhesion. Wear eye protection, take care around hot glue and hot nozzle areas. Warranty Tool is covered by a 5 year replacement warranty for DIY use. PXC lithium batteries and chargers are covered by a 36 month warranty. Keep your proof of purchase.
$52.48
Stanley 12mm 240V Corded Hot Glue Gun 25W Get clean, reliable bonds for crafts, quick household fixes, packaging, and light DIY with the Stanley 12mm Corded Hot Glue Gun. Its 25W heating element warms up efficiently for steady glue flow, while the compact body and ergonomic trigger deliver comfortable, controlled application on a wide range of surfaces. Why choose this glue gun Trusted Stanley build for everyday projects and repairs Consistent glue output for neat, repeatable results Easy to handle for beginners and experienced makers Key features 12 mm glue sticks for great coverage and fewer reloads 25W heating element for steady melt and controlled flow Ergonomic trigger that reduces hand fatigue on longer runs Built in stand and nozzle shroud to help keep benches tidy 240V corded power for uninterrupted operation Great for Cardboard, paper, fabric, felt, foam, ribbons, and craft materials Wood trims, light plastics, small fixtures, and packaging General household touch ups and temporary jigs How to use Insert a 12 mm glue stick into the feed port. Plug into a 240V outlet and allow the tool to preheat. A few minutes is typical. Gently squeeze the trigger to dispense glue. Apply in small beads or dots. Press parts together while the adhesive is hot. Hold until initial grab occurs. Rest the tool on the built in stand when not dispensing. Unplug after use. Compatibility Uses standard 12 mm hot melt glue sticks. Works with multi purpose, high tack, wood, and craft grade sticks. For heat sensitive substrates such as very thin plastics or delicate fabrics, test on a small area first. Specifications Power 25W Voltage 240V AC Glue stick size 12 mm diameter Nozzle Precision tip with protective shroud Stand Integrated flip down stand Cord Mains corded Typical applications Crafts, packaging, light repairs What is in the box Stanley 25W 12 mm Hot Glue Gun User guide Glue sticks sold separately Helpful tips Keep the nozzle clean by wiping away stringing while warm using a scrap of cardboard. For porous materials like fabric or raw timber, apply a slightly thicker bead. For smoother finishes on visible joints, apply small dots and press evenly. Safety and care Hot melt adhesive and nozzle become very hot. Avoid contact with skin. Use on a stable, heat resistant surface. Keep out of reach of children. Unplug after use and allow to cool before storage. FAQ Q: Can I use smaller mini sticks? A: This tool is designed for 12 mm sticks. Using other sizes can cause feed issues. Q: How long do I have to position parts? A: Open time varies by stick type and temperature. Work quickly and test first on your material. Note: Always test bond strength and heat suitability on an offcut before full application.
$44.10
Aftek MDF Adhesive 250 ml Overview Aftek MDF Adhesive 250 ml is a high quality fast setting MDF adhesive set designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials MDF timber trims decorative profiles Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Use in ventilated areas between 10°C and 30°C. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Activator accelerates set in seconds to minutes. Full strength develops over several hours. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Remove overspray and uncured adhesive with suitable solvent. Use carefully to avoid staining. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$8.37
Selleys Araldite Rapid Epoxy Adhesive 14 mL Fast-setting, two-part epoxy for quick, durable repairs at home, in the workshop, or on site. The self-mixing syringe makes application clean and precise, setting in about 90 seconds and reaching handling strength soon after. Dries translucent for a neat finish. Key benefits Sets in approximately 90 seconds for rapid fixes High strength bond up to 75 kg/cm² when fully cured Dries translucent for low-visibility repairs Self-mixing nozzle for easy, accurate application Versatile bonding across common materials Best for Everyday repairs and small assemblies Fixing chipped ceramics and china Metal, glass, leather, rubber, and many plastics Suitable materials China, metal, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. How to use Prep Abrade, clean, and dry both surfaces. Attach nozzle Remove cap, fit and lock the self-mixing nozzle, then purge a small amount until evenly mixed. Apply Spread adhesive on both surfaces and join within 1 minute. Hold Support the bond for about 10 minutes to prevent movement. Cure Maximum strength develops after about 16 hours. Allow longer in cold conditions. Clean up Wipe away uncured adhesive with acetone. Remove and dispose of the used mixing nozzle before the adhesive sets in the tip. Technical details Technology Two-part epoxy Set time About 90 seconds Handling time Approximately 10 minutes Full cure About 16 hours Colour when dry Translucent Temperature resistance Up to 60 °C Pack size 14 mL self-mixing syringe Good to know Bond may soften above 60 °C and regains strength when cooled. Pre-test on leather and rubber to confirm suitability. May discolor with prolonged UV exposure. Store in a cool, dry place. Replace cap after removing the used nozzle. Safety Follow the safety directions on the packaging. Use in a well-ventilated area and avoid skin contact. Keep out of reach of children.
$16.89
DEWALT Rapid-Heat Ceramic Glue Gun is a reliable robust hot glue gun with rapid heat technology and ceramic heating core chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose DEWALT Rapid-Heat for your next project Everyday jobs often involve mixed materials and imperfect surfaces. DEWALT Rapid-Heat Ceramic Glue Gun has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Site temporary fixes Cable dressing and protection Trim installation and packaging work Suitable surfaces The adhesive works well on the following surface types when properly prepared: Timber, plastics that accept hot melt Cardboard and composites Ceramic ornaments Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of seconds to position parts before set. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Fast heating means less waiting and consistent flow. Bonds set on cooling for immediate handling. Temperature and environmental performance Use in dry conditions and avoid hot melt on heat sensitive foams. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Collect stray filaments after they cool. Protect benchtops with scrap board or a mat. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Unplug, cool, and store upright. Keep spare sticks sealed. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$52.48
Stanley Mini DualMelt Hot Glue Gun is a reliable compact dual temperature hot glue gun for craft and light repair chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Stanley Mini for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Stanley Mini DualMelt Hot Glue Gun has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Paper craft and floral work Bonding trims and beads Quick household fixes that benefit from a fast set Suitable surfaces The adhesive works well on the following surface types when properly prepared: Paper, card, fabric Timber trim Plastic compatible with hot melt Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of assemble within seconds of application. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Low temp setting helps with delicate materials. High temp setting increases flow and tack for wood and rigid plastics. Temperature and environmental performance Operate in dry indoor conditions. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Remove stray strings when cool. Use a silicone mat to catch drips. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Switch off and cool before storing. Keep sticks clean and dry. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$16.28
Ozito Trigger-Flow Hot Glue Gun 10 W is a reliable compact hot melt glue gun for quick bonding and model making chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 10 W pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Ozito Trigger-Flow for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Ozito Trigger-Flow Hot Glue Gun 10 W has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Cardboard displays and craft Light repairs and cable dressing Attaching trims, felt, and fabric accents Suitable surfaces The adhesive works well on the following surface types when properly prepared: Card, paper, fabric Wood trim and plastics that tolerate hot melt Ceramic ornaments Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of open time is short, assemble parts promptly after application. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Hot melt sets as it cools, giving fast handling strength. Full strength is reached once the bead has cooled through. Temperature and environmental performance Operate in a dry area. Avoid use on heat sensitive foams that may melt. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Peel away stray strands after cooling. Protect worktops with a mat. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Unplug and allow to cool before storage. Keep glue sticks sealed from dust. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$8.38
Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL is a reliable two part fast setting epoxy adhesive for durable repairs chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 24 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Tarzan's Grip Grip for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Household and workshop repairs that need speed and strength Fixing fixtures, brackets, and hardware Filling chips and rebuilding small edges before sanding Suitable surfaces The adhesive works well on the following surface types when properly prepared: Metal hardware Ceramic tiles Most rigid plastics except polyethylene and polypropylene Timber and MDF Stone and concrete Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of 3 to 5 minutes working time. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Initial set is reached in about 5 minutes at 23 C. Sandable after several hours. Achieves high final strength after a full overnight cure. Temperature and environmental performance Performs well across typical domestic temperature ranges after cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured excess with acetone on a cloth. Use care on painted substrates. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed to prevent crystallisation. Store upright at moderate temperature. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$11.50
Get fast and reliable adhesion with Bostik Quick Glu Instant Fix Bond Spray. This 25g spray adhesive provides a strong, clear and lasting bond suitable for a wide range of materials used in craft, home and office projects. Key Features Instant bonding for quick and easy use Dries clear for a neat and professional finish Acid free formula that resists yellowing over time Works on wood, metal, ceramic, leather, paper and many plastics (not suitable for polyethylene or polypropylene) Compact 25g size ideal for small jobs and easy storage How to Use Ensure surfaces are clean, dry and free from grease or dust. Shake the can well before each use. Hold the can 15 to 20 cm from the surface and apply a light, even coat. Wait a few seconds until tacky before joining the surfaces. Press firmly together and hold for a few seconds for best results. After use, clear the nozzle by spraying briefly while holding the can upside down. Recommended Applications Arts and crafts projects DIY home repairs Paper, cardboard, leather and wood bonding Quick fixes requiring a clear and clean finish Safety and Storage Use only in well ventilated areas and avoid inhaling vapours. Keep away from heat, sparks and open flames as the product is flammable. Store in a cool, dry place away from direct sunlight. Keep out of reach of children. Bostik Quick Glu Instant Fix Bond Spray delivers a convenient and efficient solution for fast bonding on a wide variety of materials.
$8.50
Bostik Super Glue Instant Bond gives you fast, reliable fixes for everyday repairs. Each pack includes three 1 mL single-use tubes to keep the adhesive fresh and reduce clogging, so you only open what you need. Why you’ll love it Sets in seconds for quick repairs High strength, clear finish Precise nozzle for controlled application Three single-use tubes to minimise waste Best for Metal, most plastics*, rubber, ceramic, porcelain Wood trims, leather, cork, card, paper Small household, craft, hobby and DIY fixes How to use Ensure surfaces are clean, dry and close-fitting. Lightly sand smooth or glossy areas. Pierce the tube seal, fit the nozzle and apply a tiny drop to one surface. Press parts together firmly for 10 to 60 seconds. Support if needed until handling strength is reached. Allow a few hours for maximum strength before stressing the bond. Good to know Finish: Clear Chemistry: Cyanoacrylate Viscosity: Liquid for close-fitting parts Gap fill: Very low. Parts should mate tightly. Tips Less is more. Excess can slow curing and reduce strength. Store unopened tubes upright in a cool, dry place. Use each tube once opened. For porous or flexible materials, consider a flexible or gel adhesive. Limitations Not suitable for PP, PE, PTFE, silicone, glass aquariums or very oily surfaces* Not recommended for large gaps, continuous water immersion or high heat exposure *Some plastics may require a primer. Always spot test first. Safety Bonds skin and eyes in seconds. Wear protection and keep out of reach of children. Use with adequate ventilation. If spilt on skin, do not pull; soak in warm soapy water and gently roll apart. What’s in the pack 3 x 1 mL single-use tubes of clear cyanoacrylate adhesive
$8.82
Bostik Super Glue Gel is a fast setting, non drip adhesive that stays where you put it for precise, clean bonds. The thixotropic gel formula is ideal for vertical surfaces and small gap filling, delivering reliable results on everyday repairs and crafts. Key features Fast setting gel for controlled application Non drip formula for vertical and overhead surfaces Small gap filling for close fitting parts Strong bond on many common materials Clear finish for neat repairs Ideal for Metal, rubber, most hard plastics, wood, ceramics, porcelain Small household repairs, models, craft and DIY fixes Precision bonding where liquid super glue may run Not suitable for Polyethylene, polypropylene, PTFE Very flexible materials or items regularly exposed to water immersion Food contact surfaces or aquarium use Directions Ensure surfaces are clean, dry and close fitting. Lightly roughen smooth surfaces if possible. Remove cap and apply a small bead of gel to one surface. A little goes a long way. Join parts immediately and hold firmly until set. Avoid moving the bond during curing. Allow the repair to rest for several minutes before light handling and longer for full strength. Handy tips Test on an inconspicuous area first. Use sparingly. Excess adhesive can slow cure. For porous materials, a second application may improve the bond. Clean up Wipe fresh squeeze out immediately. Once cured, carefully remove excess with a sharp blade. Adhesive may whiten on some surfaces if excess is left to cure. Storage and safety Close cap tightly after use and store upright in a cool, dry place. Bonds skin in seconds. Wear care when handling. If skin bonding occurs, do not pull apart. Soak in warm soapy water and gently roll apart. Use in a well ventilated area and keep out of reach of children.
$6.47
Bostik Hard Plastics Glue is a clear, fast-setting adhesive designed for rigid plastic repairs around the home, garage, and workshop. It forms a strong, durable bond that resists impacts and everyday handling while drying clear for a neat finish. Best for ABS, PVC, acrylic, polycarbonate, polystyrene Household repairs, toys, car trim, appliance covers Small craft fixes and model making Not suitable for Polyethylene or polypropylene PTFE or silicone surfaces Surfaces that are oily, dusty, or wet Key features Clear finish that blends with most plastics Fast initial grab with strong final cure Impact and vibration resistant Precision nozzle for controlled application Surface preparation Ensure surfaces are clean, dry, and free from dust, grease, or release agents. Lightly roughen glossy plastic with fine sandpaper to improve adhesion, then wipe clean. How to use Test on a small hidden area first. Apply a thin, even layer to one surface. Avoid excess. Join parts immediately and hold firmly for 30 to 60 seconds. Allow to set undisturbed. Handling strength is typically reached within minutes. Full cure develops over 12 to 24 hours depending on temperature and humidity. Tips For tight fitting parts, less is more. A thin film gives the strongest bond. Use clamps or tape to maintain alignment while the adhesive sets. Cleanup Wipe fresh adhesive immediately with a suitable solvent on a cloth. Cured residue may need careful mechanical removal. Storage and safety Replace cap after use and store upright in a cool, dry place. Use in a well ventilated area. Avoid skin and eye contact. Keep out of reach of children.
$12.72
Bostik Repair All is a clear, multi-purpose adhesive for quick, durable repairs around the home, garage, and workshop. It bonds strongly, remains slightly flexible, and is water resistant once cured, making it suitable for everyday fixes and craft projects. Why you will love it Strong, long lasting bond Dries clear for a neat finish Water resistant once fully cured Flexible bond helps absorb vibration Suitable for indoor and outdoor use Works on Metal, wood, ceramics, glass, most rigid plastics, rubber, leather, fabric, and more. Always test on delicate or unknown materials first. Ideal for Household repairs and DIY Craft, hobbies, and school projects Fixing ornaments, toys, trims, and fittings Directions Ensure surfaces are clean, dry, and free of dust or grease. Lightly roughen smooth surfaces. Apply a thin even layer to one surface. Join parts together and press firmly. Support or clamp if needed. Wipe away any squeeze out immediately with a cloth dampened with solvent suitable for the substrate. Allow to set undisturbed. Handling strength is typically reached within hours. Full cure is usually achieved after 24 hours depending on bead size, temperature, and humidity. Clean up Uncured adhesive can be removed with a suitable solvent. Cured adhesive is best removed mechanically by trimming or carefully scraping. Good to know Not recommended for polyethylene, polypropylene, PTFE, or surfaces that will be in constant water immersion. Avoid contact with food or drinking water surfaces. Store upright in a cool dry place with cap tightly closed. Key details Brand Bostik Product Repair All Appearance Clear when dry Finish Flexible Water Resistance Yes, once cured Pack Size 20ml Always read the label and follow safety instructions. Keep out of reach of children.
$14.50
Keep your glue gun ready for any project with the Bostik HG3 Glue Gun Refills. These high quality hot melt sticks provide a smooth, even flow for clean and reliable bonding. Pack of 10 clear adhesive sticks Compatible with Bostik HG3 Glue Gun Creates a strong, flexible and transparent bond Suitable for wood, plastic, fabric, leather, ceramics and more Perfect for craft work, household repairs and DIY projects. The hot melt formula ensures quick adhesion with minimal mess, giving you professional results every time. How to use: Insert a glue stick into the back of your glue gun. Allow the gun to heat for a few minutes before use. Apply steady pressure on the trigger to release glue. Join surfaces immediately for best results. Let the glue cool completely before handling. Safety Information: Hot glue can cause burns. Avoid contact with skin and eyes. Keep out of reach of children. The Bostik HG3 Glue Gun Refills are ideal for quick fixes, decorative projects and reliable everyday bonding.
$15.21
Overview LOCTITE Super Glue All Plastics is a rapid dual-action adhesive kit featuring a precision super glue and a surface activator pen. Engineered to bond difficult plastics such as polyethylene (PE), polypropylene (PP) and PTFE, it forms clear, resilient bonds in seconds and resists water, most household chemicals and freezing temperatures. Ideal for repairs on toys, cameras, small automotive parts, wiper blades, rubber seals, figurines and other plastic components. Advanced bonding system: activator primes the surface; glue delivers high strength. Fuses hard-to-bond plastics: effective on PE, PP, PTFE and more. Fast & clear: sets in seconds, dries transparent for nearly invisible repairs. Durable: water-resistant and suitable for cold conditions. Surface Preparation Ensure both surfaces are clean, dry and close-fitting. Remove grease, oil, dust or loose particles. For best adhesion on very smooth plastics, lightly roughen with fine-grade sandpaper and wipe clean. Avoid use on soft foams, expanded polystyrene or highly porous materials. Always test on a small, inconspicuous area if unsure about compatibility. Application Instructions Prime with activator: Apply one or two thin coats to both bonding surfaces, ensuring full coverage. Re-cap the activator pen immediately. Allow to dry/react for 1–2 minutes. Apply adhesive: Place a minimal drop of glue on one surface only. Bring parts together immediately and hold firm pressure for at least 1 minute. Avoid shifting once contact is made. Cure: Leave undisturbed for 10 minutes. Full bond strength develops after 12–24 hours at room temperature. Coverage & Performance Only a thin film is required—one drop bonds most small mating areas. Initial handling strength is typically achieved within 5–30 seconds depending on substrates and conditions. Drying & Setting Time Initial set: 5–30 seconds* Handling time: ~1 minute Full cure: 12–24 hours Recommended conditions: 15–30 °C and ≥30% relative humidity *Setting and cure times vary with substrate, joint fit, temperature and humidity. Clean-Up & Storage Wipe nozzle to remove excess adhesive and replace caps immediately after use. Store upright in a cool, dry place away from sunlight and moisture. Do not refrigerate. Shelf life (unopened and properly stored): up to 18 months. Limitations Not recommended for glass, very flexible materials, soft foams or highly porous substrates. Not suitable for continuous water immersion or high-heat applications. For indoor use or dry environments; test before critical repairs. Safety & Handling Contains cyanoacrylate. Bonds skin and eyes in seconds. Avoid contact. Use in a well-ventilated area; consider gloves and eye protection. If skin is bonded, do not pull apart—soak in warm, soapy water and gently roll/separate. Acetone may assist on non-sensitive skin; avoid on plastics. If in eyes, rinse cautiously with water and seek medical attention immediately. Keep out of reach of children. Technical Data Product Type Two-part system: Activator + Cyanoacrylate Adhesive Substrates PE, PP, PTFE, many rigid plastics, rubber, selected metals Appearance Clear (dries transparent) Packaging Size 2 g adhesive + 4 ml activator Initial Set 5–30 seconds (substrate dependent) Full Cure 12–24 hours at ambient conditions Temperature Range Approx. −50 °C to +80 °C (typical for cured cyanoacrylates) Cleanup Mechanical removal once cured; avoid solvents on sensitive plastics What’s Included LOCTITE Super Glue (2 g) Surface Activator Pen (4 ml) Always follow on-pack directions. Performance will vary with materials, joint design and environmental conditions.
$9.64
Bostik Ultra-Strong Clear Super Glue (Liquid, Odourless, Fast-Setting) Ultra-Strong Clear Super Glue is a professional-grade, medium-viscosity liquid adhesive designed for quick, reliable repairs on most non-porous materials. It forms an instant high-strength bond that sets in seconds and reaches full cure in 24 hours. The clear, solvent-free formulation is virtually odourless for a cleaner, more comfortable user experience, and its slightly flexible bond helps resist knocks and everyday drops once cured. Why You’ll Love It Fast setting: bonds in seconds to get you back to work quickly. Ultra strong: high strength once fully cured for durable, long-lasting repairs. Water & heat resistant: engineered to stand up to common household moisture and temperature swings. Odourless & solvent-free: cleaner application with a safer, low-irritation formula. Slightly flexible bond: helps absorb minor shocks and everyday handling. Ideal Materials Best results on clean, dry, non-porous surfaces including: China, ceramics and porcelain (non-permanent on items subject to frequent washing) Rubber and elastomers Metals and metal components Jewellery repair (non-food contact) Many rigid plastics* *Not suitable for polyethylene (PE), polypropylene (PP) or PTFE (Teflon®). Not recommended for permanently bonding glass, high-alkaline materials, or items that are regularly washed. Avoid paper and other highly porous substrates. Where It Excels Quick household fixes (knobs, clips, figurines, trim) Hobby & craft assembly (non-porous parts) Workshop touch-ups and small component repair Office and general repair kits How It Works This liquid cyanoacrylate reacts with trace moisture on surfaces to polymerise rapidly, forming a high-strength thermoplastic bond. The medium viscosity helps wet out tight-fitting parts while minimising run-off when applied sparingly. Before You Start Surface prep: Ensure both surfaces are clean, dry, and free from dust, oil, rust, release agents or old adhesive. Lightly abrade glossy plastics/metal where appropriate and wipe clean. Dry fit first: Check alignment, clamping and support so parts come together quickly and accurately. Protect work area: Use disposable backing and keep caps, tissues and a small amount of acetone or nail-polish remover handy for cleanup. Application (Liquid) Open: For first use, attach/screw the nozzle and remove the cap. Apply a tiny amount: Place a small drop on one surface only. More glue can slow cure and weaken the joint. Assemble: Bring parts together immediately and hold with firm, even pressure for ~20 seconds. Avoid movement during initial set. Let it cure: Handling strength develops quickly; allow 24 hours for full cure and maximum performance. Clean-Up & Rework Fresh squeeze-out: Wipe carefully. Small residues may be treated with acetone/nail-polish remover and gently scraped once softened. On skin: Do not pull apart. Soak in warm, soapy water and gently roll/peel. Use a blunt tool (e.g., spoon handle) to separate bonded skin slowly. Pro Tips for Best Results Use the smallest effective drop—thin bondlines are stronger. Maintain close-fitting joints; gaps reduce cure speed and strength. Avoid bonding on PE, PP, PTFE and materials with heavy plasticisers or strong alkalinity. Allow the full 24-hour cure before exposing to stress, moisture or heat. Storage & Shelf Life Store tightly closed in a cool, dry place below 25 °C, away from direct sunlight. Typical shelf life: 12 months from manufacture when stored as directed. Safety Cyanoacrylate adhesive: bonds skin and eyes in seconds. Keep out of reach of children. Wear protective gloves and eye protection. In eyes: rinse immediately with water and seek medical attention. Specifications Technology Modified Ethyl Cyanoacrylate (liquid, medium viscosity) Appearance / Colour Clear Typical Working / Set Time Up to ~20 seconds (conditions and substrates affect speed) Full Cure 24 hours Water & Heat Resistance Resistant after full cure (not for continual immersion or high-temperature structural loads) Odour / Solvents Virtually odourless; solvent-free formulation Bond Character Slightly flexible; resists minor knocks and drops when fully cured Suitable Substrates China, ceramics, rubber, metal, jewellery, many rigid plastics (non-porous, clean, dry) Not Recommended PE, PP, PTFE; permanent glass bonds; high-alkaline materials; frequently washed items; paper/very porous substrates Cleanup (Uncured) Acetone or nail-polish remover; scrape gently once softened Storage Cool, dry, below 25 °C; protect from sunlight Shelf Life 12 months from manufacture (stored as directed) FAQs Can I use it on flexible rubbers? Yes, many rubbers bond well; ensure surfaces are clean and oil-free. Is it dishwasher-safe? Not recommended for items that are regularly washed, soaked or immersed. Why shouldn’t I flood the joint? Excess adhesive slows cure and weakens the bond—thin layers perform best. Disposal Allow small residues to cure fully (exposed to air) before disposal in accordance with local regulations.
$7.89
Holds up to 13.6Kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$11.55
Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistantRecommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$12.95
Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$23.00
Casting, modelling, moulding, sculpting, carving. Fine quality to hold detail. Sands smooth.
$16.64
Casting, modelling, moulding, sculpting, carving. Fine quality to hold detail. Sands smooth.
$8.50
UHU All Purpose Adhesives Super Strong & Safe, the super strong and super fast adhesive, which is adjustable - no instant finger bonding. Suitable for virtually all flexible, solid, porous and non-porous materials. Formula patented. Withstands vibrations and tremors. Moisture and heat resistant from -50°C to +100°C. Materials Universal - glues porcelain, ceramic, many plastic materials, metal, wood, glass, leather, rubber, Styrofoam®, paper, cardboard. Not suitable for leather clothing, textiles, PE and PP. Use and Handling Instructions Surfaces to be stuck together must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. Press parts together. Glue joint remains correctable for approx. 20 seconds. The thinner the film of adhesive, the stronger the bond.
$10.74
3 x 1g originally sealed tubes ideal portion for one application. in a handy storage box reaches the smallest corners and joints Extra strong super glue in 3 x 1g tubes, packaged in a small storage box, ensuring optimal quality for every new application. The liquid adhesive reaches the smallest corners and joints. Materials Glues many plastics, porcelain, ceramic, metal, wood and rubber. Not suitable for leather clothing, PE, PP nor styrofoam. Use and Handling Instructions Surfaces to be stuck together must fit exactly and must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. The thinner the film of adhesive, the stronger the bond. Press the parts together immediately and hold in place for a short time. Breathing upon the surfaces to be stuck will speed up bonding. After use, wipe the applicator tip dry and close firmly. Will last longer if stored in a cool place.
$11.50
PROPERTIES Extra strong Fast but temporarily adjustable Does not drip Ideal for porous materials and vertical surfaces Dishwasher proof and water resistant APPLICATION SUITABLE FOR: Ideal for small-area bonds. Glues almost all solid and flexible materials like ceramics, leather, rubber, many plastics (such as rigid PVC, ABS, PS, Plexiglas®, polycarbonate (Makrolon®), and phenolic resins (Bakelite®)), porcelain, metal, wood, cork, felt, and cloth (check suitability first). Only partly suitable for glass (over a certain period of time the bond becomes brittle, causing it to weaken). Ideal for porous materials. NOT SUITABLE FOR: Not suitable for PE, PP, silicone resins, PTFE, Styrofoam®, fabrics and leather clothing. BEFORE USE: Working conditions Do not use at temperatures below +10 °C. The glue responds best to an air humidity level of 50-70 %. Surface requirements Surfaces to be glued must be clean, dry, and free of dust and grease, and must fit exactly. Preliminary surface treatment Any dust, oil, grease, wax or separating agent should be thoroughly removed from the surfaces to be stuck together. The best way to achieve this is to rub the parts a number of times with appropriate solvents, such as acetone (if suitable for the material – check first!). For metals and metal alloys it is usually sufficient to roughen the surface using emery paper or by grinding or brushing. DURING USE: Directions for use 1. To pierce the membrane, turn the cap clockwise firmly onto the tube. Tip: do not press the tube while piercing. 2. Unscrew the cap to reveal the applicator. Apply the adhesive directly from the tube, using the nozzle, as thinly as possible onto one side (too much glue slows down the curing process significantly). Press parts together immediately. After use, clean nozzle with a dry tissue and replace cap. Advice When glueing at low humidity, curing time can be shortened by briefly breathing onto one of the parts to be assembled. The best glueing results are reached at room temperature. Points of attention Contains cyanoacrylate. Bonds skin and eyelids together in seconds. If product comes into contact with the eyes, rinse immediately with plenty of water and seek medical advice. In case of contact with skin, glue can be dissolved by soaking in warm soapy water. Then apply a skin cream. May cause respiratory irritation. Avoid breathing vapours. Keep out of the reach of children. AFTER USE: Stains/residue Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue but very slowly (check suitability first). Storage conditions Store in a dry, cool, frost-free place. Storage below +5 °C (in refrigerator) ensures maximum shelf life.
$7.00
Ultra-fast and extremely strong universal super glue. Its liquid formula is easy to spread and flows into smallest corners and joints. UHU Super Glue is easy to apply, bonds quickly and provides lasting, extremely strong results. You can use it on a variety of materials so it's perfect for keeping handy in the classroom at school. You can use the glue on plastics, ceramics, wood, porcelain, metal and rubbers. It bonds quickly for fast results. The glue will flow into small corners and tight spaces. The results are extremely strong and long lasting.
$7.00
$33.09
$16.48
You have seen 48 out of 163 products
Fast-acting solutions for quick repairs and production tasks. Great for small parts and close-fit joints; consider gels for vertical surfaces. Use filters to refine by chemistry and set time. Always check the product page and TDS/SDS.