Stick

A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safetytips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.

Read more less

Colours to suit almost any timberWaxstix are so easy to use and so handy for quick repairs to scratched or damaged timber. Waxstix can be coated and stained. Plus, Waxstix contain no beeswax so they will not leave any white ring marking otherwise known as the "halo effect". For most small scratches, simply rub the stick over the damaged area. For larger, deeper indentations (where TIMBERMATE water-based Woodfiller cannot be used), heat a knife blade with a flame or a soldering iron or stove lighter and fill the damaged area with hot wax. Remove excess wax by rubbing with the smooth side of sandpaper, a piece of cardboard or an old credit card. Use a cotton cloth to buff and remove excess wax.

Read more less

PC-Fahrenheit™ Putty Epoxy is the choice for temperatures up to 260° C. It is supplied as a premeasured stick that you mix with fingers. Fast curing (60 min). Best for steam heat applications. A toolbox must. Great on copper and iron. Here are just a few specific uses (there are hundreds of other uses): Seal cracked steam or hot water radiator Stop leaking steam fittings Fill hole in heat exchanger Attach thermocouple to hot surface Seal chimney ductwork How to prepare a surface for bonding with PC-Fahrenheit™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Fahrenheit™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Fahrenheit™ repair a leaking steam radiator? PC-Fahrenheit™ resists higher temperatures and is suitable for repairing steam pipes and radiators. Can PC-Fahrenheit™ be used in a fireplace or wood burning stove? PC-Fahrenheit™ will withstand temperatures up to 260°C. A fireplace or wood burning stove creates temperatures exceeding 260°C. Can PC-Fahrenheit™ be used to seal heater chimney duct? PC-Fahrenheit™ is excellent for use on sheet metal and the temperature is within an acceptable range. Can PC-Fahrenheit™ seal a rust hole in barbecue grill? PC-Fahrenheit™ can be used on the barbecue grill exterior but is not recommended for the interior. How long should PC-Fahrenheit™ be mixed before applying? Mix PC-Fahrenheit™ for 45 to 60 seconds then immediately apply. What is the temperature limit? PC-Fahrenheit is not intended to exceed 260°C. -  Will PC-Fahrenheit™ burn? PC-Fahrenheit™ is not flame resistant and may burn if exposed to direct flame. Does PC-Fahrenheit™ stick to car radiator? Car radiators are made of various metals and plastic composites. Test for adhesion and test for leaks.

Read more less

Key features Goes on blue, dries clear for easy, mess free gluing Non toxic, acid free and solvent free Fast drying with a strong hold on porous materials Allows brief repositioning before it sets Twist up stick with tight sealing cap to prevent drying out Low mess and easy to use for kids and adults Great value multi pack for classrooms and home offices Ideal for Paper and cardboard Photos and craft paper Lightweight fabric embellishments School assignments, posters and scrapbooks Directions Surfaces should be clean, dry and free of dust. Uncap and twist the base to raise the glue. Apply a thin, even layer to one surface. Join parts and press firmly for several seconds. Allow to dry. Full strength is reached after the glue has set clear. Clean up and safety Wipe fresh residue with a damp cloth. Wash hands and tools with warm soapy water. Keep capped when not in use. Keep out of reach of young children. Good to know Not recommended for non porous surfaces like metal or glass. For best results, store in a cool, dry place. Pack contents 10 glue sticks x 35 g each.

Read more less

Meet your go to epoxy putty for fast, permanent style repairs. Gorilla All Purpose Epoxy Stick is a hand mixable putty that sets in about 10 minutes and cures in 24 hours to a tough, machinable finish. Once cured it can be drilled, sanded, and painted. It is waterproof, non rusting, and ready for indoor or outdoor jobs around the home, car, boat, and garden. Why you will like it Fast setting. Approximate set time 10 minutes. Paintable after about 1 hour. Full cure in about 24 hours for a hard wearing repair. Works on most common materials including metal, PVC, many rigid plastics, wood, stone, ceramic, brick, concrete, fiberglass, and glass. Non rusting formulation for durable repairs in wet or humid areas. Waterproof when cured. Suitable for indoor and outdoor use. NSF ANSI 61 certified drinking water safe for contact with potable water once cured. Great for Plumbing repairs such as sealing low pressure leaks and patching drainage pipes Automotive trims and general panels that do not exceed service temperature of typical epoxy repairs Household fixes like filling holes, anchoring hardware, rebuilding small parts, and edge repairs DIY and craft projects that need a sculptable, sandable fill Important use notes Not for exhaust systems. For plumbing, use for temporary repair of drainage pipes or low pressure pipes only. Turn water off, apply, then wait at least 1 hour before turning water back on. Bonded wood should not be submerged or soaked after repair. How to use Wear disposable gloves. Work in a well ventilated area. Prepare the surface. Clean off dust, oil, and loose material. Roughen smooth surfaces with sandpaper. Cut the amount you need. Remove the film wrapper and foil sticker. Reseal unused putty to limit air exposure. Knead for 30 to 60 seconds until the colour is uniform. Mix thoroughly or it will not harden completely. Apply within 5 minutes of mixing. Press firmly into place. Smooth with wet gloved fingers if a smooth finish is desired. Remove any squeeze out before hardening. Allow to set about 10 minutes. Paint after about 1 hour. Full cure about 24 hours. Specifications Format Hand mixable epoxy putty stick Size 56.7 g Set time About 10 minutes Paintable After about 1 hour Full cure About 24 hours Indoor or outdoor Yes, waterproof when cured Drill, sand, paint after cure Yes Drinking water contact NSF ANSI 61 certified drinking water safe once cured Clean up and storage While uncured, wipe away with soap and water, acetone, or isopropyl alcohol. For cured material, remove by sanding, scraping, or chiseling. Store the stick in its vial with film and foil sticker re applied. Keep sealed in a cool, dry place. Keep away from children and animals. Safety Wear gloves during mixing and application. Avoid contact with skin and eyes. Use in a well ventilated area. For medical emergencies in Australia call 000. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Bostik Blu Stik is the glue stick that solves the problem every teacher and parent knows: children cannot see where they have already glued. It goes on blue, so coverage is obvious, then dries completely clear so the finished work looks clean. This listing is a five pack of 21g sticks, a handy size for younger hands and for topping up a pencil case, craft caddy or classroom tub without paying for glue that dries out before it is used.The formula is solid, solvent free and non-toxic, which is why it has been a classroom standard in Australia for decades. It is acid free, so it will not yellow photographs or corrode the paper underneath over time, and the non-wrinkle characteristic keeps lightweight paper flat instead of buckling as it dries. The twist-up base lets you expose only as much glue as you need, and the cap seals tightly to stop the stick drying out between uses.Where to use itIndoors Cut and paste activities, worksheets and school projects Scrapbooking, journaling and album work Card making, collage, invitations and paper craft Dry mounting photographs and artwork General office and home stationery jobs on paper and light card OutdoorsNot suitable. This is a water soluble stationery adhesive with no moisture or weather resistance, so anything heading outdoors needs a different product.What it bondsPorous materials, including paper, cardboard, photographs, tissue and crepe paper, and lightweight fabric. Surfaces need to be clean and dry.How to use Check both surfaces are clean and dry. Remove the cap and turn the base until a small amount of glue protrudes. Expose only what you need. Apply an even layer to one surface. The blue colour shows exactly where you have covered. Press the two surfaces together firmly. Turn the base back to retract the glue and recap straight away. Tip: a stick left uncapped and dried out can usually be revived by standing it in warm water for a few minutes rather than being thrown away.Important notes For lightweight bonding only. Not suitable for heavy duty or structural repairs. Not suitable for non-porous surfaces such as metal, glass or most plastics. No water resistance. Keep finished work dry. Always recap after use. Store between 5°C and 30°C, away from direct sunlight. Contains corn starch. Free from wheat, gluten, flour, egg and nut ingredients, though repeated or prolonged contact may cause an allergic reaction in susceptible people. Specifications Brand Bostik Product Blu Stik Pack 5 x 21g sticks Type Solid stick stationery adhesive Colour Blue on application, dries clear Solvent content Solvent free Acid free Yes Finish Non-wrinkle, clear Clean up Warm soapy water Suitable surfaces Paper, cardboard, photographs, light fabric Storage 5°C to 30°C, away from direct sunlight Compliance Tested to AS/NZS ISO 8124.3 (Safety of Toys, migration of certain elements) SafetyIt is still an adhesive rather than a toy. Keep it away from very young children, avoid eye contact and do not eat it. Residue on skin, clothing and surfaces washes off with warm soapy water. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safetytips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.

Read more less

Make neat, mess free sticking simple. Bostik Tri Stik is a triangular glue stick that reaches right into corners, stops rolling off the desk, and applies smoothly for reliable bonds that dry clear. Perfect for school projects, craft, office paperwork, and everyday repairs. Key features Triangular shape for precise edges and easy grip Dries pink  Non toxic, acid free, solvent free Smooth application with even coverage Washable from hands and most fabrics Won't wrinkle most papers when used correctly Best for Paper, cardboard, photos, light craft materials School book work, posters, scrapbooks, presentations Home and office use Directions Ensure surfaces are clean, dry, and free from dust. Twist the base to raise the glue 3 to 5 mm. Apply a thin, even coat to one surface. For porous papers, coat both sides for a stronger bond. Press surfaces together firmly and hold for a few seconds. Replace cap tightly after use to prevent drying. Clean up and safety Wipe away wet excess with a damp cloth. Wash hands and tools with warm soapy water. Limitations Not suitable for heavy duty bonding or non porous surfaces such as metals, glass, polyethylene, or polypropylene. Storage Store capped, upright, in a cool dry place away from heat and direct sunlight. Contents: 25 g triangular glue stick.

Read more less

A versatile hand kneadable, fast setting, non-rusting co-extruded epoxy repair system that can be used for repairing ferrous and aluminium metal items. It comes in a handy roll form, with the black hardener encapsulated in the grey resin part. The product hardens in 5-10 minutes, after mixing, to a black metal-like material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under water (but dry surfaces for application are best and recommended). Rapid Set (less than 10 minutes). Can be used for fuel resistant repairs. Appearance Dries Dark Grey/Charcoal Where can this product be used? Rebuilding engine parts and rusted metal etc Repairing a hole in a fuel tank Repair of iron pipes, tools and equipment Repair stripped threads Forming of nuts and bolts in place Attaching fixtures and signs Fixing radiators Repairing holes in cars and boats Patching ducts and tanks Making prototypes Thread locking Repair of down pipes and gutters Anchoring of bolts Repairing your metal outdoor furniture Set time increases at temperatures below 20°C Not recommended for plastic fuel tanks Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Not tested for drinking water contact to AS/NZ 4020:2005 What materials is this product suitable for? Steel Wide range of terrous metal and aluminium items Most plastics (pre-test required) Glass How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning Cut off required amount. Replace disc on remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to uniform colour. If mixing is difficult, warm to room temperature. Apply with pressure to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Steel will harden and begin to form a strong bond. After 60 minutes Knead-It Steel may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour, and feel a mild heat radiating from thre knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Store in a cool place for maximum shelf life Use Knead-It Multi Purpous for applications in contact with drinking water. Use Knead-It Aqua for applications in wet/submerged areas. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safetytips Where possible wear protective gloves when using Knead-It Steel. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.

Read more less

PC-Plumbing™ Epoxy Putty is for pipes. Use PC-Plumbing™ to stop leaks in less than 60 minutes. Pre-measured and easy to use and 2 part epoxy putty does not require tools. Hand mix and apply. NSF® approved for plumbing repairs and for contact with potable water supply pipes.  Here are just a few specific uses (there are hundreds of other uses): Seal leaks in copper pipes resulting from hard water Fix freeze damaged PVC and copper pipes Stop leaking copper elbow and tees Fill abandoned drill holes in ductwork Insulate electrical connections from water

Read more less

PC-Crete™ Epoxy is a hand-mixable, fast-setting epoxy putty that quickly repairs concrete and masonry. After mixing, it forms a concrete repair polymer that cures to a concrete-like color and texture. The mixture readily sticks to concrete and masonry surfaces and is easily shaped. It will stick to ceramics, glass, metals and some plastics. It cures within 60 minutes. Each stick contains pre-measured portions of activator and base — no measuring or mixing tools are necessary. Here are just a few specific uses (there are hundreds of other uses): Quickly rebuild small missing pieces of concrete Fill holes in concrete and masonry Rebuild missing pieces of statues and birdbaths Seal hole for wire or conduit thru cinder block Fill chip or spall in concrete furniture Reattach loose or popped decorative stone Fill crack in stone fireplace Fill holes in brick or concrete walls; Apartment complexes, schools, government buildings etc. Fill cracks in concrete or stucco wall before painting Attach address numbers to brick or stone Attach hardware to brick or stone Fill abandoned screw holes and mounting holes in brick or cinderblock Replace missing mortar Seal rodent hole in cinderblock or concrete How to prepare a surface for bonding with PC-Crete™ Old concrete must be clean and profiled or textured. Surface must be clean and sound. It may be dry or damp, but free of standing water. Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use mineral spirits or paint thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-Crete™ application Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be removed with paint stripper or remover. Can PC-Crete™ be used to repair a crack in a fountain? PC-Crete™ looks like concrete and is excellent for repairing concrete fountains, statues and lawn decorations. Will PC-Crete™ adhere to a concrete step? Can it be shaped to match a corner? PC- Crete™ is excellent to repairs on concrete surfaces such as steps. It shapes easily and can be sanded to match the look and texture of the concrete surface. Is PC-Crete™ suitable for filling a small crack or spall in a sidewalk or deck? Small crack repairs in concrete are easily made with or without the use of tools using PC-Crete™. PC-Crete™ is excellent for replacing missing or loose mortar between bricks and stones. Can PC-Crete™ be used in a fish tank or pond? PC-Crete™ is not recommended for aquatic use. Do not use this product in aquariums or ponds. The PC-Crete™ is not easily grabbing or sticking to the concrete surface. It pulls away lifting loose stones The putty wants to stick to the fingers more than the concrete surface. Wet the fingers with alcohol and then press, shape and smooth the applied putty. Also, loose stones can be wire brushed away to provide a sound surface. PC-Crete™ does not have a smooth texture. It has particles throughout The particles in PC-Crete™ are used to simulate the appearance of concrete.

Read more less

BostiBostik Glu Stik is a clear, mess free adhesive designed for quick everyday sticking at home, school, and the office. It glides on smoothly, dries clear, and is perfect for paper projects that need a clean finish without wrinkling. Why you will love it Dries clear for a neat finish Solvent free and non toxic Low mess, easy to control twist up stick Washable from most fabrics Photo safe and acid free Ideal size for pencil cases, craft kits, and desk drawers Best for Paper and cardboard Scrapbooks, school projects, craft, and gift wrapping Office tasks like mounting notes and labels How to use Ensure surfaces are clean, dry, and free of dust. Twist the base to expose a small amount of glue. Apply a thin, even layer to one surface and press parts together. Adjust positioning within a short open time, then hold or smooth down to bond. Good to know Not suitable for heavy or structural bonding. For best results on photos or coloured paper, apply lightly to prevent over wetting. Replace cap after use to prevent drying out. Clean up and safety Fresh residue wipes away with a damp cloth. Wash from most fabrics in a standard warm wash. Non toxic, however supervision is recommended for young children. Specifications Brand Bostik Product Glu Stik Clear Glue Stick Size 8 g Color when dry Clear Solvent content Solvent free pH and acid content Acid free, photo safe Primary materials Paper, cardboard Clean up Water wipe while wet, machine washable from most fabrics Frequently asked questions Can I use it on photos? Yes. The formula is acid free and photo safe, making it suitable for photo mounting and scrapbooking. Does it dry clear? Yes. It applies smoothly and dries clear for a tidy finish. What materials does it bond? It is designed for porous, lightweight materials such as paper and cardboard. It is not intended for plastics, metal, glass, or heavy items. What is in the pack 1 x Bostik Glu Stik Clear Glue Stick 8g

Read more less

Make neat, mess free sticking simple. Bostik Tri Stik is a triangular glue stick that reaches right into corners, stops rolling off the desk, and applies smoothly for reliable bonds that dry clear. Perfect for school projects, craft, office paperwork, and everyday repairs. Key features Triangular shape for precise edges and easy grip Dries clear for a clean finish Non toxic, acid free, solvent free Smooth application with even coverage Washable from hands and most fabrics Won't wrinkle most papers when used correctly Best for Paper, cardboard, photos, light craft materials School book work, posters, scrapbooks, presentations Home and office use Directions Ensure surfaces are clean, dry, and free from dust. Twist the base to raise the glue 3 to 5 mm. Apply a thin, even coat to one surface. For porous papers, coat both sides for a stronger bond. Press surfaces together firmly and hold for a few seconds. Replace cap tightly after use to prevent drying. Clean up and safety Wipe away wet excess with a damp cloth. Wash hands and tools with warm soapy water. Keep out of reach of young children when not in use. Limitations Not suitable for heavy duty bonding or non porous surfaces such as metals, glass, polyethylene, or polypropylene. Storage Store capped, upright, in a cool dry place away from heat and direct sunlight. Contents: 25 g triangular glue stick.

Read more less

A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safetytips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.

Read more less

PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.

Read more less

PC-Lumber™ Epoxy Putty is pre-measured and mixed by hand. It is used as a filler where a small amount will solve the problem. Within 60 minutes it is cured and ready. The putty can be easily formed and shaped. Here are just a few specific uses (there are hundreds of other uses): Reset or secure loose hardware in wood (hinges, handles, latches, etc.) Fill abandoned screw and nail holes in cabinets or paneling Fill dings and dents in molding or doors Fill woodpecker and carpenter bee damage to exterior siding and paneling Rebuild display corner in retail store

Read more less

Bostik Hot Melt Sticks are made of a general purpose translucent flexible hot melt in a stick form for use with the Bostik Hot Melt Glue Gun. It provides an instant, fast, clean and versatile bond between a myriad of household and craft materials and suitable for many porous materials. Recommended Uses Ideal for: Craft projects Home décor projects Minor household repairs DIY projects Materials Designed to stick to: Most craft and household materials Fabric  Wood Leather Most plastics  Polystyrene  Ceramics Features Once heated and gunned out, it provides instant adhesion Adhesive is clear and flexible when dry Fast, clean and versatile

Read more less

The Timbermate Timber Touch Up Kit gives you a water-based wood filler and a set of wax touch-up crayons in four timber shades, so you can deal with dents, gaps and scratches around the house without sanding back a whole surface. It suits furniture, floors, door and window frames, architraves, staircases and picture frames, and it is simple enough for first-time repairers.About the formulaThe kit pairs two products. Timbermate is a water-based, interior grade wood filler made without acrylic or latex, which is why it resists shrinking, sinking, cracking and falling out of the repair. The pre-mixed colours can also be tinted with any stain or colourant to fine-tune a match. It has an indefinite shelf life, and if it dries out in the tub it can be reconstituted. Waxstix are synthetic wax crayons that contain no beeswax, so repairs accept coatings and avoid the pale ring that beeswax-based products can leave around the edges. Several sticks can be blended to match a colour or to imitate grain.Where to use itIndoors: touch-ups on timber furniture, floors, staircases, architraves, window and door frames and picture frames.Outdoors: not recommended, as this kit is intended for interior use only.Suitable for timber surfaces. The filler can be sanded, stained or painted once dry, and Waxstix repairs can be coated over.How to use itClean the damaged area and make sure it is free of dust and loose material. For gaps, holes and dents, press the woodfiller in with a scraper or putty knife, let it dry, then sand flush before staining, painting or coating. For most scratches, simply rub a Waxstix across the damage. For deeper marks, warm the stick with a flame and let the hot wax flow into the area. Scrape off any excess with a plastic scraper or a piece of cardboard. Blend more than one stick if you need a closer colour match.Important notesDrying time for the filler depends on how deep the fill is, so allow extra time for deeper repairs before sanding. Colour is easiest to judge by testing on an offcut or an out-of-sight spot first. Keep the lid on the tub when not in use to prevent it drying out. Not intended for exterior timber.Specifications Brand Timbermate Product Timber Touch Up Kit, Mixed Colours Kit contents 4 x Timbermate water-based woodfiller tubs and 4 x Waxstix touch-up crayons Colours Pine, Walnut, Hardwood (Tasmanian Oak), Mahogany Base Water-based wood filler (no acrylic or latex) and synthetic wax crayon (no beeswax) Application Filler by scraper or putty knife; Waxstix rubbed on or melted in Finishing Sandable, paintable and stainable Pack dimensions Approx. 165 x 117 x 35 mm Use Interior only SafetyUse with normal care. Work in a well-ventilated area and wear gloves if you prefer to keep your hands clean. If you heat a Waxstix, keep flammable materials away, take care with the hot wax and let it cool before handling. Keep out of reach of children and store the tubs sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Boyle Hot Melt Glue Sticks are a pack of eight clear 7mm sticks made for use in a high temperature glue gun, handy for home, office and school craft projects. They give a quick, strong hot glue bond on lots of everyday craft and household materials, and they suit most handicraft jobs.About the formulaThese are clear hot melt glue sticks. According to Boyle, they are non-toxic, odourless and acid free, and they dry clear so the glue line stays discreet on finished projects. Each stick is 200mm long and 7mm in diameter, so check that your glue gun takes 7mm sticks before you buy.Where to use itIndoors: craft and handicraft projects, school and homework projects, office jobs, jewellery making and quick household fixes.Outdoors: not recommended. The supplier lists this product for indoor use only.Suitable materials include cardboard, ceramics, fabric, glass, jewellery, paper, plastic, leather, metal and wood. It is a good idea to test on a small hidden spot first, especially on plastics and delicate or heat-sensitive items.How to use it Load a stick into a high temperature glue gun with a 7mm barrel and let the gun heat up fully. Make sure the surfaces are clean, dry and free of dust and grease. Squeeze the trigger to lay glue on one surface, then press the parts together straight away and hold them until the glue cools and sets. Work quickly, as hot melt glue cools fast and loses its tack. Important notesThe supplier does not list this product as child friendly, so children should only use it with close adult supervision. Molten glue and the gun nozzle get very hot and can cause burns. Do not touch hot glue with bare skin. Not recommended for outdoor use. Set and cure times and temperature resistance of the bond have not been published by the manufacturer, so test before relying on it for anything that will be heated or put under load. The sticks are sold on their own and do not include a glue gun.Specifications Brand Boyle Product Hot Melt Glue Sticks Pack 8 sticks Stick size 200mm long x 7mm diameter Colour Clear Application High temperature glue gun Use Indoor use only Features Non-toxic, odourless, acid free, dries clear SafetyMolten hot melt glue can cause serious burns, so avoid skin contact, use the glue gun on a stable heat-safe surface and unplug it when you have finished. Use in a well-ventilated area and keep out of reach of children. Store the sticks in a cool, dry place away from heat. If you get hot glue on your skin, cool the area under cold running water straight away and do not peel off the glue. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Stanley Dual Temp Mini Glue Sticks are all-purpose hot melt glue sticks for 7mm mini glue guns, supplied here as a 24-pack of 100mm sticks for craft, hobby and household jobs. They are made for mini hot melt, low temperature and dual temperature guns, so you can bond delicate, heat-sensitive materials as well as everyday items.About the formulaA thermoplastic hot melt adhesive based on ethylene vinyl acetate (EVA) and petroleum resin, with no solvents to evaporate. Because it is a dual melt formula, it can be run on a low heat setting for materials that would be damaged by high heat, or on a high heat setting for harder, non-porous surfaces. The glue sets quickly as it cools, usually within about 15 to 30 seconds.Where to use itLow temperature setting: paper, ribbon, foam and other delicate or heat-sensitive materials in craft and hobby projects.High temperature setting: china and leather, and general household repairs and fastening jobs.Suitable materials include paper, cardboard, leather, china and other non-porous surfaces, and heat-sensitive craft materials such as polystyrene foam, ribbon and dried flowers. Test on a small, hidden area first if you are unsure how a material will react to heat.How to use it Check that your glue gun takes 7mm mini glue sticks. These sticks are not compatible with standard 11mm glue guns. Make sure surfaces are clean, dry and free of dust and grease. Load a stick into the gun and let it heat fully. Choose the low setting for delicate materials or the high setting for china, leather and other non-porous surfaces, if your gun has a temperature switch. Apply the glue to one surface, press the parts together straight away and hold them still until the glue sets. Unplug the gun and rest it safely when you finish. Important notesWork quickly, as hot melt glue starts to set within seconds of application. Molten glue and the gun nozzle can cause burns, so keep them away from skin and children. Hot melt adhesive is not designed for heavy structural loads or for surfaces that stay hot, because the bond can soften when reheated. Glue guns are sold separately.Specifications Brand Stanley Product Dual Temp Glue Sticks (Dual Melt Mini) Model number 1-GS10DT Pack 24 sticks Stick size 7mm diameter x 100mm length Colour White Base Thermoplastic hot melt (EVA and petroleum resin) Application Mini hot melt, low temperature and dual temperature glue guns Set time About 15 to 30 seconds Use Craft, hobby, household and general fastening SafetyThe main hazard is thermal burns from molten glue, which can cause intense pain and tissue damage. Avoid breathing fumes from heated glue and use the gun in a well-ventilated area. If it gets in the eyes, flush with water while holding the eyelids open and seek medical care straight away. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Craftright Hot Melt Glue Sticks are a clear, 20 pack of mini glue gun refills aimed at craft, hobby and light household projects. They suit any hot glue gun that takes a 7.2mm stick, so they are a handy way to keep a compact glue gun stocked for a long run of jobs.About the formulaThese are clear hot melt adhesive sticks. The stick melts inside the glue gun, comes out as a hot, tacky bead, then cools and sets quickly as it returns to room temperature. Craftright describes them as quicker setting than many other glue types, and as giving a secure bond on many different materials.Where to use itIndoors: craft and hobby projects, model making, decorating, small repairs and general fixing around the house.Outdoors: no outdoor or weather-resistance claims are confirmed for this product, so test a sample first if you plan to use it outside.Suitable for joining a range of common craft and household materials. Because the maker does not list specific surfaces, always test on a small hidden area first, particularly on foam, thin plastics and other heat-sensitive materials.How to use itMake sure the surfaces are clean, dry and free of dust, oil and grease. Load one stick into a hot glue gun that accepts 7.2mm sticks and let the gun heat fully, following the gun maker's instructions. Apply a bead to one surface, press the parts together promptly and hold them still until the glue has set and cooled.Important notesUse only in guns designed for 7.2mm sticks. Do not force a stick into a gun with a wider barrel. Work quickly, because hot melt adhesive starts to set soon after it leaves the nozzle. Open time, bond strength and temperature resistance are not confirmed by the manufacturer for this product, so do not rely on it for structural, load-bearing or high-heat situations.Specifications Brand Craftright Product Hot Melt Glue Sticks Pack 20 sticks Stick size 7.2mm x 100mm Colour Clear Base Hot melt adhesive Application Hot glue gun with 7.2mm stick capacity Use Craft and hobby SafetyMolten glue and the gun nozzle get hot enough to cause burns, so keep them away from skin, children and pets. Do not touch freshly applied glue. Use the gun on a stable, heat-safe surface and unplug it when you finish. If you get hot glue on your skin, cool the area under running water straight away and do not peel the glue off. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Craftright Clear Hot Melt Glue Sticks are a handy 12 pack of full-size EVA sticks for hot glue guns, made for everyday repairs, woodwork and craft projects. Each stick is 10.8mm thick and 100mm long. That suits a range of glue guns, and the pack gives you a ready supply for the workshop, the craft table or the classroom.About the formulaThese sticks are made from EVA hot melt adhesive and are clear in colour. Once melted in a glue gun and applied, the adhesive cools and sets to form a permanent bond. They are a simple, solvent-free-style fix for small jobs where you want a quick, tidy result. They are not a replacement for structural adhesives.Where to use itIndoors: minor household repairs, small woodworking and hobby projects, model making, decorations, school and craft activities.Outdoors: not specified by the manufacturer, so test a small area before relying on the bond in exposed conditions.Suitable for general use on timber and wood-based projects and for arts and crafts work. Always test an offcut first when bonding other materials, particularly plastics, foams and delicate finishes.How to use itCheck that the stick diameter suits your glue gun before loading, as the 10.8mm size will not fit guns made for other stick sizes. Make sure surfaces are clean, dry and free of dust, oil and grease. Load a stick into the gun, let the gun heat fully, then apply the molten adhesive to one surface. Press the parts together promptly and hold them steady until the adhesive cools and sets. Work in small sections, because hot melt cools and sets quickly.Important notesThese sticks are designed for use with a hot glue gun only. Do not use them as a stand-in for structural or load-bearing adhesives. Heat-sensitive materials can be damaged by molten adhesive. Performance on specific surfaces, set times and temperature limits are not confirmed by the manufacturer for this product, so test before committing to a job.Specifications Brand Craftright Product Hot Melt Glue Sticks Pack 12 sticks Stick size 10.8mm diameter x 100mm length Colour / finish Clear Base EVA hot melt Application Melted in a hot glue gun Bond Permanent SafetyAs general hot melt guidance, molten adhesive and the glue gun nozzle get very hot and can cause serious burns. Never touch melted adhesive, keep it away from skin and children, and use the gun on a stable, heat-safe surface. Use in a well-ventilated area, unplug the gun when finished and let it cool fully before storing. Store the sticks in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Gilly's Beeswax Filler Sticks are coloured wax sticks for repairing cracks, gaps and small holes in timber, supplied here as an assorted pack of six sticks in different wood tones. You pick the shade closest to your timber, work the wax into the damage and finish the surface, which suits furniture, cabinets, frames and general timber touch-ups.About the formulaThese are pigmented wax fillers made from pure beeswax, natural pigments and a natural hardener. Once set, the wax can be buffed to a fine finish and coated with most materials. The manufacturer says the colours can be blended, and leftover wax can be melted down and reused.Where to use itIndoors: filling nail holes, gaps, joins and cracks in furniture, cabinetry, frames and other timber items.Outdoors: the manufacturer does not publish outdoor performance data for this product, so it is best treated as a timber repair filler for interior and finished-furniture work.Suitable for most wood surfaces, in both soft and hard woods. It is aimed at damage wider or deeper than about 1mm. Very fine scratches and surface blemishes are better treated with a wax product made for that job.How to use itStart with a clean, dry surface and apply the filler to raw timber before any oil, wax or lacquer finish. Pick the stick closest to the timber, or melt two colours together to blend a custom match. Soften the wax with a soldering iron, a hot knife, or gentle heat from a heat gun or hairdryer. Take care, because extra heat can affect the surrounding finish. You can also soften a stick briefly in a microwave. Test in very short bursts, as it only needs to become malleable. Press the softened wax into the gap. For larger repairs, chip off the amount you need and melt it into the gap. Once the wax has firmed up again, scrape off the excess with a plastic spatula or an old card, then buff to a smooth finish. Important notesThe wax firms up quickly after application, typically within about 10 to 30 minutes depending on conditions. Rubbing a cold stick over a gap like a crayon works, but adhesion is better when the wax has been melted. Beeswax can ignite when overheated, so the manufacturer advises caution and says not to apply an open flame directly to the sticks. The product may contain traces of bee pollen and soy. If you plan to use it on a surface that will touch food, check suitability with the manufacturer first, as the coloured sticks are pigmented.Specifications Brand Gilly's Australia Product Beeswax Filler Sticks, Assorted Pack 6 sticks, 15g each (about 90g in total) Stick size About 83mm long x 15mm diameter Colours Pale brown (natural), orange/brown, mid brown, red/brown, dark brown, black (one of each) Base Beeswax with natural pigments and natural hardener Application Hand applied; melt or soften the wax, press into the gap, then scrape back and buff Firming time About 10 to 30 minutes, depending on conditions Use Timber repair, applied before the final finish Origin Made in Australia SafetyTake care when heating the wax, as molten wax can burn skin and beeswax can ignite at high temperatures. Keep it away from open flames and avoid overheating. Allow the wax to cool before handling. Store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Bostik Glu Stik is the classic clear-drying glue stick that generations of Australian classrooms, craft rooms and home offices have run on. This listing is a bulk pack of ten 35g sticks, which is the economical way to buy for a school term, a busy studio, an office stationery cupboard or a community group that goes through glue faster than anyone expects.The formula is a solid, solvent free adhesive that glides on smoothly and dries clear, so finished work looks clean rather than patchy. It is acid free, which matters when you are mounting photographs or building a scrapbook that needs to survive a few decades without yellowing or corroding the materials underneath. The non-wrinkle characteristic means lightweight paper stays flat instead of buckling as the glue dries. The twist-up applicator keeps hands clean and lets you control how much stick is exposed at a time.Where to use itIndoors Scrapbooking, journaling and album building Cut and paste activities, school projects and classroom worksheets Paper craft, card making, collage and invitations Dry mounting photographs and artwork General office and stationery work on paper and light card OutdoorsNot recommended. This is a water soluble stationery adhesive with no weather or moisture resistance, so anything destined for outdoor exposure needs a different product.What it bondsPorous materials, including paper, cardboard, photographs, cellophane, crepe and tissue paper, foil and fabric. Surfaces need to be clean and dry for a reliable bond.How to use Check that both surfaces are clean and dry. Remove the cap and turn the base clockwise until a small amount of glue protrudes. Expose only what you need. Apply with firm, even strokes to one surface. Press the two surfaces together. Initial grab is roughly 20 to 40 seconds. Turn the base anti-clockwise to retract the glue and recap straight away so the stick does not dry out. Tip: if a stick has been left uncapped and has dried out, sitting it in warm water for a few minutes will usually bring it back rather than sending it to the bin.Important notes Designed for lightweight bonding. It is not suitable for heavy duty repairs or structural work. Not suitable for non-porous surfaces such as metal, glass or most plastics. No water resistance. Bonded work should be kept dry. Always recap after use. An uncapped stick will dry out. Store between 5°C and 30°C, out of direct sunlight. The formula contains corn starch. It is free from wheat, gluten, flour, egg and nut ingredients, though repeated or prolonged contact may cause an allergic reaction in susceptible people. Specifications Brand Bostik Product Glu Stik Pack 10 x 35g sticks Type Solid stick stationery adhesive Colour White stick, dries clear Solvent content Solvent free Acid free Yes Initial grab Approximately 20 to 40 seconds Clean up Warm soapy water Suitable surfaces Paper, cardboard, photographs, fabric Storage 5°C to 30°C, away from direct sunlight Compliance Tested to AS/NZS ISO 8124.3 (Safety of Toys, migration of certain elements) SafetyIt is non-toxic and solvent free, which is why it is cleared for classroom use, but it is still an adhesive and not a toy. Keep it out of reach of very young children, avoid eye contact, and do not eat it. Wash residue off skin and surfaces with warm soapy water. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Bostik Green Stik is an easy to use glue stick for everyday crafting, school projects, and office tasks. It applies smoothly, goes on clear, and dries clear for a neat finish. Why you will love it Non toxic and acid free Smooth application with strong initial tack Ideal for paper crafting, cut and paste, and classroom use Low mess and easy to control for kids and adults Surfaces Paper Cardboard Light fabric and similar porous materials How to use Ensure surfaces are clean, dry, and free from dust. Twist the base to raise the glue. Apply a thin, even layer to one surface. Press surfaces together firmly for several seconds. Allow to dry. For best results on heavier paper, apply to both surfaces. Clean up Wipe away excess with a damp cloth while still wet. Allow to dry fully before handling. Environment and packaging Formulated with a high percentage of natural ingredients Packaged in a recycled plastic container with soy ink label Packaging is curbside recyclable in many areas when the lid is attached Good to know Colour when applied: clear Dries: clear Size: 35 g

Read more less

Bostik Pink Stik is a neat, no-mess glue stick that goes on pink so coverage is easy to see, and dries pink to add fun colour to your creations. Perfect for school projects, craft, scrapbooking and everyday office use. Why you will love it Goes on pink and dries pink Smooth application with quick grab Non toxic and acid free Low mess twist up tube Washable from hands and most fabrics Best for Paper, card and photos School assignments and scrapbooks Office presentations and collages How to use Ensure surfaces are clean, dry and free from dust. Twist up a small amount of glue and apply a thin, even coat to one surface. Join surfaces and press firmly. For heavier card, apply to both surfaces. Replace cap after use to prevent drying out. Clean up and safety Fresh glue washes off skin with soap and water. Wipe excess from surfaces with a damp cloth before it dries. Keep out of reach of young children when not in use. Specifications Brand Bostik Product Pink Stik Glue Stick Size 35 g Colour (wet) Pink Colour (dry) Pink Suitable materials Paper, card, photos, light fabrics Not recommended for glossy plastics, foam, or other non porous surfaces where a stronger adhesive is required.

Read more less

Bring colour to craft time with Bostik Glu Stik Rainbow. These smooth-gliding, non toxic glue sticks make school projects, scrapbooks, posters and office tasks quick and tidy. They go on smoothly, dry clear and are washable from hands and most fabrics, making them ideal for kids and classrooms. Key features Vibrant rainbow set for fun, easy-to-see application Non toxic and solvent free for peace of mind Dries clear for a neat, professional finish Low mess stick format with twist up design Washable from hands and most washable fabrics Acid free formula suitable for photos and paper crafts Best for Paper, cardboard and lightweight craft foams School homework, posters and collages Scrapbooking and photo mounting Office and home stationery tasks How to use Ensure surfaces are clean, dry and free of dust. Twist base to expose glue and apply a thin, even coat to one surface. Press surfaces together and smooth from the center outward. Allow to dry. For heavier paper, hold or weight for a stronger bond. Clean up Wipe away excess with a damp cloth while wet. Wash hands with warm soapy water. On washable fabrics, pre treat with stain remover and launder according to garment instructions. Helpful tips Replace cap firmly after use to prevent drying out. Use on porous, lightweight materials only. Not suitable for metal, glass or heavy plastics. Test on a small area of delicate papers or photos first. Specifications Format Glue sticks Pack size 5 sticks Stick weight 35 g each Colour Rainbow set. Dries clear Solvent Solvent free pH Acid free Safety: Keep out of reach of young children when not in use. Do not ingest. If irritation occurs, discontinue use.

Read more less

Key features Goes on blue, dries clear for easy, mess free gluing Non toxic, acid free and solvent free Fast drying with a strong hold on porous materials Allows brief repositioning before it sets Twist up stick with tight sealing cap to prevent drying out Low mess and easy to use for kids and adults Great value multi pack for classrooms and home offices Ideal for Paper and cardboard Photos and craft paper Lightweight fabric embellishments School assignments, posters and scrapbooks Directions Surfaces should be clean, dry and free of dust. Uncap and twist the base to raise the glue. Apply a thin, even layer to one surface. Join parts and press firmly for several seconds. Allow to dry. Full strength is reached after the glue has set clear. Clean up and safety Wipe fresh residue with a damp cloth. Wash hands and tools with warm soapy water. Keep capped when not in use. Keep out of reach of young children. Good to know Not recommended for non porous surfaces like metal or glass. For best results, store in a cool, dry place. Pack contents 5 glue sticks x 35 g each.

Read more less

Keep your glue gun ready for any project with the Bostik HG3 Glue Gun Refills. These high quality hot melt sticks provide a smooth, even flow for clean and reliable bonding. Pack of 10 clear adhesive sticks Compatible with Bostik HG3 Glue Gun Creates a strong, flexible and transparent bond Suitable for wood, plastic, fabric, leather, ceramics and more Perfect for craft work, household repairs and DIY projects. The hot melt formula ensures quick adhesion with minimal mess, giving you professional results every time. How to use: Insert a glue stick into the back of your glue gun. Allow the gun to heat for a few minutes before use. Apply steady pressure on the trigger to release glue. Join surfaces immediately for best results. Let the glue cool completely before handling. Safety Information: Hot glue can cause burns. Avoid contact with skin and eyes. Keep out of reach of children. The Bostik HG3 Glue Gun Refills are ideal for quick fixes, decorative projects and reliable everyday bonding.

Read more less

Key benefits Goes on purple, dries clear for easy, accurate application Low mess, quick grab on paper and card Washable formula that cleans up with water Solvent free and non toxic, suitable for school use Twist up stick for smooth, even coverage Great value multi pack for home, school, and office Best for Paper and cardboard Photos and scrapbooking Homework and classroom crafts Gift wrapping and arts projects How to use Ensure surfaces are clean, dry, and free from dust. Twist the base to raise the stick a few millimetres. Apply an even coat to one surface using light pressure. Join within 30 seconds and press firmly along the bond line. Allow to dry. Handling strength is reached in minutes, full bond develops as it cures. Clean up and storage Fresh residue wipes away with a damp cloth. Wash hands and tools with water. Replace cap after use to prevent drying out. Store upright in a cool, dry place. Typical details Format Solid glue stick Colour when applied Colours Colour when dry Clear Set time Minutes, depending on coat weight and ambient conditions Clean up Water while wet Suitable materials Paper, card, photos, light crafts Not recommended for Non porous surfaces, heavy materials, or outdoor use Pack contents 4 x 8 g glue sticks  

Read more less

Make stubborn marks and sticky residue disappear with Bostik Fix Stik Marker & Sticker Remover. This compact 8 g twist-up stick lifts everyday messes like label glue, tape gum, crayon and marker from hard surfaces so you can restore a clean, tidy finish fast. Why you’ll love it Targets sticky residue and ink marks for quick clean up Twist-up solid stick gives precise application with less mess Handy pocket size for pencil cases, drawers and tool kits Works on most non porous surfaces when used as directed Suitable surfaces Glass, ceramic, sealed stone, metal, whiteboards, laminated desks, most plastics and finished timber. Always test on an inconspicuous area first. How to use Ensure the surface is dry and free from loose dirt. Twist up a small amount and apply directly to the mark or residue. Allow to sit briefly, then wipe with a soft cloth. Repeat if needed for heavier buildup. Good to know Not recommended for porous fabrics, unsealed wood or delicate coatings. Avoid extended contact with printed or lacquered finishes. Test first. Keep capped when not in use to prevent drying. Clean up Wipe treated area with a clean dry cloth. If required, finish with a damp cloth and dry thoroughly. Storage and safety Store in a cool dry place away from heat and direct sunlight. Keep out of reach of children. Avoid contact with eyes. If irritation occurs, discontinue use. Specifications Format Twist-up solid stick Size 8 g Colour Clear Application Spot treatment of marks and residue

Read more less

A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safetytips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.

Read more less