Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load):– At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area– At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.
$25.37
Selleys Auto Fix Auto Sealant Translucent 100 mL Keep water out and vibrations at bay with a clear automotive sealant that bonds fast and stays flexible. Selleys Auto Fix Auto Sealant is a 100 percent neutral cure silicone designed for cars, caravans, and general automotive sealing where a durable waterproof finish is essential. Why you will like it 100 percent neutral cure silicone Versatile general purpose sealant for automotive use Waterproof seal that resists vibration and temperature extremes UV and weather resistant for long lasting performance Skins in 5 minutes, set to touch in 30 minutes, full cure in 24 hours Where to use it Adheres to most auto and caravan materials, including: Glass and painted surfaces Fiberglass and most plastics Trim components Most rubbers Typical applications Sealing around lights, windows, and trim Gasket style sealing where a flexible waterproof joint is required General leak prevention and small gap sealing in automotive and caravan fittings Directions Preparation: Clean surfaces so they are free of dust, oil, and moisture. Wipe with mineral turpentine and allow to dry. Cut and load: Remove cap, unscrew nozzle, remove seal. Refit nozzle and cut at a 45 degree angle to the desired bead size. Apply: Squeeze the tube with steady pressure to lay a continuous bead. Smooth with a gloved finger before the sealant skins. Clean up: Before cure, clean tools and excess with mineral turpentine. Once cured, remove by cutting or scraping. After use: Replace cap. Let cured material in the nozzle be removed before next use. Handy tips Mask edges for neat joints. Remove tape before skin forms. Work within the skin time to achieve a smooth finish. Limitations Not recommended for Natural rubber, NBR, or Chloroprene Neoprene Technical details Technology 100 percent neutral cure silicone Colour Translucent Packaging Tube 100 mL Density 1.02 g per mL Application temperature -20°C to 50°C Skin time 5 minutes Shore A hardness 25 Elongation at break 370 percent Movement capability 25 percent Service temperature -40°C to 180°C VOC 26 g per L Clean up and storage Clean uncured sealant with mineral turpentine Store below 30°C in a cool dry place Use within 24 months from date of production Safety: Refer to the product SDS for handling and first aid information. Use in a well ventilated area and keep out of reach of children.
$22.57
Liquid Nails Clear eliminates unsightly mess caused by conventional brown construction adhesives because it dries clear and blends with the surrounding surface. It is ideal where a fine finish is important. Uses Selleys Liquid Nails Clear is suitable for bonding to glass, fibreglass, metals, most plastics*, timber, particleboard, MDF, tiles & ceramics, concrete, painted and masonry substrates. Suitable for bonding mouldings & trims, skirting boards & architraves, general fabrication and creating mosaics. Pre-test plastics to determine compatibility. Technical Features High performance solvent based adhesive. Note: When use on glass to glass, thin film application is recommended for better clarity. Good paintability – Paintable with water based paints. Oil based paints require undercoating with water based paints first. Excellent resistance to water and weather makes it suitable for interior and exterior applications. Application Tips Due to solvent content Liquid Nails Clear should not be used in enclosed space or without ventilation Solvents may affect some plastics Will not bond polyolefin plastics such as polyethylene and polypropylene May damage some polycarbonate, avoid smears and spills Cannot be used on polystyrene foam May not adhere to wet absorbent surfaces or to some old wet metals In very cold weather cartridge must be conditioned to room temperature before use Not recommended for permanent water immersion or water containment structures Must be first painted with water based paint prior to painting with oil based paints Will not accept common wood stains. (If staining is required, it is recommended to stain timber before bonding). Full cure in 2 weeks Not recommended for mirrors Bonds weaken at high temperatures. Avoid bonding metals or heavy materials which will be heated by direct sun. (Consult Selleys about particular applications subject to heating). Ensure that surfaces are free from dust, loose particles and dry. Cut cartridge tip, pierce membrane inside base of nub, fit nozzle and cut end to desired opening and fit cartridge into cartridge gun. In very cold weather, cartridge may need to be conditioned to room temperature for easier gunning. Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. (“zig-zag” beads are more appropriate on surfaces of moderate width) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are re-positionable for up to 20 mins after fitting Allow adhesives to set (at least 24 – 48 hours) before removing any temporary fasteners or clamping. (refer to Bond strength Time) For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-3 minutes before firmly Technical Details and Performance Time for strong bond depends on nature and condition of application. A minimum of 24 to 48 hours is needed for sufficient strength to develop. The bond will continue to strengthen over time. Full cure up to 14 days. Curing is achieved by evaporation of solvent. Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (e.g. metals and glass). Indicative information only, not to be used for setting specifications. Appearance Clear soft adhesive Viscosity 5000 – 9000P TE/2 @ 25oC HAF/HELIPATH Skin Time / Tack Free Time 5 min. @ 25oC Specific Gravity 0.87g/mL Extrudability 100g/min. @ 25oC (at 628kPa pressure through 3mm orifice) Solid Content 60% Cure By evaporation of solvent Water Based Paints Good Alkyd Paints Good, after first undercoating with a water based paint Flammability Uncured adhesive- flammable Cured adhesive – will burn if ignited Service Temperature Maximum 80oC Coverage 15 metres of a 5mm diameter bead Cleaning Clean off wet adhesive with mineral turps or white spirit. Dry adhesive can be removed by scraping or sanding.
$19.41
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-14 Thread Sealant Anaerobic Adhesive 50ml Loxeal 55-14 is a medium strength anaerobic thread sealant for hydraulic and pneumatic threaded connectors up to 1-1/2″. It replaces PTFE tape and hemp for sealing against gases, water, LPG, hydrocarbons, oils and many other chemicals. A medium thixotropic consistency stops the sealant migrating out of the thread before or during cure, and the cured joint is highly resistant to heat, corrosion, shocks and vibration across a service range of -55°C to +150°C. Why choose Loxeal 55-14? General purpose sealer for hydraulic and pneumatic fittings up to 1-1/2″ Replaces PTFE tape and hemp – no shredding, no re-taping, no clogged valves Medium strength – joints can still be dismantled with normal tools Thixotropic formula stays on the thread instead of dripping or migrating Seals against gases, water, LPG, oils, hydrocarbons and many chemicals Resists shock, vibration and corrosion from -55°C to +150°C Typical applications Sealing threaded connectors on hydraulic and pneumatic systems Pipework carrying water, compressed air, LPG, oils and industrial fluids General plumbing and maintenance sealing of metal pipe threads How to use Clean and degrease both threads with Loxeal Cleaner 10 and allow to dry. Apply a bead of sealant around the male thread so the gap is completely filled. Assemble and tighten the connection. Allow to cure before pressurising. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to speed the cure. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 5–10 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Red (fluorescent under blue light) Viscosity (+25°C) 2,500–12,000 mPa·s, thixotropic Specific gravity (+25°C) 1.05 Max thread size / gap fill M56 / 2″ / 0.30 mm Shear strength (ISO 10123) 8–12 N/mm² Breakaway torque (ISO 10964) 12–18 N·m Prevailing torque (ISO 10964) 20–30 N·m Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Important notes Formulated for metal threads only – contact a technical service before use on other materials. The liquid sealant can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$34.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 53-11 Retaining Compound Anaerobic Adhesive 50ml Loxeal 53-11 is a medium strength anaerobic retaining compound for fixing bearings, liners, bushes, keys and splines into housings and onto shafts. It fills the space between cylindrical parts to give 100% surface contact, boosting load-carrying capacity while still allowing disassembly with standard workshop methods. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals across a service range of -55°C to +150°C. Why choose Loxeal 53-11? General purpose retainer for bearings, bushes, liners, keys and splines Medium strength – parts remain serviceable and can be dismantled Fills the joint completely, preventing fretting corrosion between mating parts Increases load transmission compared with a mechanical fit alone Low viscosity wicks into close-fitting cylindrical assemblies Resists vibration, oils, fuels and many chemicals from -55°C to +150°C Typical applications Retaining bearings and bushes in housings and on shafts Securing cylinder liners, keys, splines and sleeves Workshop repairs to restore security in worn cylindrical fits How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts, seating them fully, and hold in position for the cure time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Yellow (fluorescent under blue light) Viscosity (+25°C) 400–650 mPa·s Specific gravity (+25°C) 1.05 Max thread size / gap fill M20 / 0.12 mm Shear strength (ISO 10123) 8–12 N/mm² Breakaway torque (ISO 10964) 11–20 N·m Prevailing torque (ISO 10964) 15–25 N·m Impact strength (ASTM D-950) 1–5 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, petrol and brake fluid at +25°C (out to 5,000 hours), with good resistance to 50% water/glycol at +87°C. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$39.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 82-21 Retaining Compound Fast Cure Anaerobic Adhesive 50ml Loxeal 82-21 is a fast curing, high strength anaerobic retaining compound for close-fitting cylindrical parts – shafts, bushes, pulleys and rotors. Its low viscosity flows into precise fits, reaching handling strength in as little as 5–10 minutes, and cures to a tough bond with 17–22 N/mm² shear strength. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils and hydrocarbons across a service range of -55°C to +150°C. Why choose Loxeal 82-21? Fast fixture – handling strength in 5–10 minutes keeps jobs moving High strength bond for permanent retention of close-fitted parts Low viscosity penetrates precise cylindrical fits (up to 0.10 mm gap) High impact strength of 11–15 kJ/m² for parts under shock loading Fills the joint completely, preventing fretting corrosion Resists vibration and many chemicals from -55°C to +150°C Typical applications Bonding pulleys, gears and rotors onto shafts Retaining bushes and bearings in precision housings Production assembly where fast fixture times are needed How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts promptly, seating them fully, and hold for the fixture time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 5–10 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green Viscosity (+25°C) 120–180 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M12 / 0.10 mm Shear strength (ISO 10123) 17–22 N/mm² Breakaway torque (ISO 10964) 24–35 N·m Prevailing torque (ISO 10964) 50–60 N·m Impact strength (ASTM D-950) 11–15 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to refrigerants (Freon) at +25°C, excellent resistance to petrol out to 500 hours, and moderate resistance to motor and gearbox oils at +40°C over extended exposure. Important notes High strength – intended as a permanent retaining bond. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$44.95
Selleys Auto Fix Windscreen Sealant 100 mL - Black Stop leaks fast around windscreens and windows with a durable, weather resistant silicone seal. Selleys Auto Fix Windscreen Sealant forms a waterproof barrier that resists vibration, UV and temperature extremes, keeping water, dust and drafts out. Why choose this sealant 100 percent neutral cure silicone for reliable sealing Forms a waterproof seal to stop leaks quickly UV and weather resistant for long term performance Skins in 5 minutes and is touch dry in about 30 minutes Handles joint movement up to 25 percent Suitable surfaces Glass and windscreens Rubber surrounds and trims Painted surfaces and most plastics Metal frames and channels Typical applications Sealing between windscreen glass and rubber Sealing between rubber and metal frames Stopping minor water ingress around vehicle windows General sealing where a flexible, black silicone finish is desired Key specifications Technology Neutral cure silicone Colour Black Movement capability Up to 25 percent Skin time About 5 minutes Set time About 30 minutes Full cure Approximately 24 hours Service temperature -40°C to 180°C Application temperature -20°C to 50°C VOC 26 g/L Pack size 100 mL tube Directions Remove any dirt or moisture between the rubber and glass, or rubber and metal. Clean with mineral turpentine and allow to dry. Remove cap, unscrew nozzle, pierce inner seal, refit nozzle, then cut the tip at a 45 degree angle. Insert the nozzle between the rubber and glass or rubber and metal where possible. Squeeze the tube with steady pressure to push sealant into the joint. Smooth off with a gloved finger. If additional smoothing is needed, do it before the sealant skins. Clean up uncured sealant with mineral turpentine. Cured material must be cut or scraped away. Replace the cap after use. Allow sealant in the nozzle to cure, then remove before next use. Handy tips For neat lines, mask both sides of the joint and remove tape before the sealant skins. Best results occur when the joint is clean, dry and free of loose material. Limitations Not recommended on natural rubber, NBR or chloroprene neoprene due to poor adhesion. Clean up and storage Clean uncured sealant with mineral turpentine. Remove cured sealant by cutting or scraping. Store in a cool, dry place below 30°C. Use within 24 months of production. What you get 1 x Selleys Auto Fix Windscreen Sealant 100 mL - Black
$23.08
Quick Setting Single Use Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 5 minutes. Works best on: All-Purpose Ceramic Metal Pottery Wood Tile Crafts Fabric Properties: Initial colour: Clear hazy to light yellow Final colour: Light yellow Set Time: 4-6 minutes @ 65-80F Handling Time: After 30 minutes Full Strength: 24 hours Maximum Gap:25" Hardness, Shore D: 75-83 (After full cure) Shear Strength, Steel: 1200 psi ( 20%) Operating Temperature Range: -40o F to +176oF (-40oC to +80oC) Instructions: 1. Surfaces should be clean and dry, free of oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from containers following package directions and mix thoroughly approximately 1 minute. 4. Apply mixed epoxy to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours. Storage: After use, wipe tips to remove residual product and reseal the container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains Epoxy resin & Mercaptan hardener. May cause eye/skin irritation with direct contact. In case of direct eye contact, flush with water for 15 minutes and consult a physician. Wash hands and skin thoroughly with soap and water after use. If swallowed, seek medical advice immediately and show container label. Keep out of reach of children.
$29.95
$15.00
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very quick setting in 90 seconds No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling Good chemical resistance Appearance: Clear with a slight yellow tinge Where can this product be used? General small household repairs Fixing gemstones to mounts Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Most Plastics How to use this product: General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately. Ensure correct caps are replaced on each tube or they will adhere. Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$13.17
Reliable options for moderate heat environments such as kitchens, lighting housings, electronics and machinery guards. Balance temperature rating with required flexibility, clarity and set time. For plastics, verify compatibility at temperature; for metals, consider gap-fill and vibration resistance. Use filters to refine by chemistry, cure speed and application method. Always check the product’s maximum service temperature and instructions on the product page and TDS/SDS.
