![Sika SikaSeal Roof & Gutter Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9318324010461.png?v=1754724138&width=645)
![Sika SikaSeal Roof & Gutter Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324010454.png?v=1754724138&width=645)
SikaSeal® Roof & Gutter Silicone Sealant Product Type: 1-component neutral cure roof and gutter silicone sealant Product Overview SikaSeal® Roof & Gutter is a versatile, one-component, neutral curing silicone sealant designed for use in roofing and guttering applications. This sealant offers excellent adhesion to a variety of construction materials and is ideal for sealing roofs, gutters, and plumbing fixtures, both for exterior and interior applications. It cures quickly and provides a flexible, waterproof seal with superior temperature resistance. Key Features Neutral cure, low odour formula Excellent adhesion to common construction materials such as glass, metals, ceramics, tiles, plastics, concrete, and rubber Fast curing with a non-sag formula for easy application Interior and exterior use with a temperature resistance range of -40°C to +150°C High movement capability (±25% for translucent, ±50% for coloured variants) Waterproof seal for durable, long-lasting performance Non-toxic and water-potable approved per AS/NZS 4020:2018 Applications SikaSeal® Roof & Gutter is ideal for: Roof and gutter sealing Sealing polycarbonate roof sheeting General sealing around plumbing fixtures and penetrations Sealing interior and exterior joints Specifications Packaging 300ml cartridge Shelf Life 12 months (if stored properly) Colours Available Translucent, Grey, White, Black Density Translucent: ~1.02 kg/l, Colours: ~1.39 kg/l Shore A Hardness Translucent: ~26, Colours: ~46 Elongation at Break Translucent: ~250%, Colours: ~310% Movement Capability Translucent: ±25%, Colours: ±50% Service Temperature -40°C to +150°C Application Instructions Ensure the substrate is clean, dry, and free from oils, grease, dust, and other contaminants. For optimal adhesion, follow the recommended priming procedures based on the substrate type (non-porous or porous). Apply SikaSeal® Roof & Gutter using a sealant gun, ensuring full contact with the joint sides. Tool the sealant immediately after application for a smooth, durable finish. Important Considerations Do not apply on natural stone or bituminous substrates Not recommended for use under water pressure or in permanent water immersion Pre-test required on stressed polyacrylate and polycarbonate materials May cause discoloration on light-colored silicone when exposed to UV radiation (this does not affect the product's performance) Not suitable for use in confined spaces with no air circulation (requires atmospheric moisture to cure) Packaging & Storage Store in the original, unopened packaging in a dry location between +5°C and +25°C. Shelf life is 12 months from the production date under proper storage conditions. Contact & Ordering For more information or to place an order, contact us at admin@gluesaustralia.com.au
$14.67
![Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240085.jpg?v=1754724137&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$26.50
![Sika Sikaflex Pro+ Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$24.84
![Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697114952.jpg?v=1754724133&width=645)
![Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Off White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125002.jpg?v=1754724133&width=645)
High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. Safety Tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
$14.77 - $21.71
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697125187.jpg?v=1754724132&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125200.jpg?v=1754724131&width=645)
Selleys SolarFlex Selleys SolarFlex provides protection from ultraviolet (UV) radiation and other harsh weather elements. Harsh Australian and New Zealand conditions make the choice of an effective solar/weather protection solution critical. Features Superior weather protection Long-lasting flexibility No primer required before painting Watertight seal with a 10-year guarantee* Adhesion to wet or damp surfaces Non-bubbling Better curing and extrudability (>5°C) with no slump Paintable with water-based paints after product skins in 60 to 90 minutes Low VOC** Where can this product be used? Skylights Walls Patios Floors Fencing Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics* *Not suitable on polyethylene, polypropylene, or Teflon. Application Instructions Ensure substrates are clean and free of oil, grease, or loose particles. Cut the seal and nozzle, then fit it to the cartridge and place it in the caulking gun. Hold the caulking gun at a 45° angle and gun the sealant ahead of the nozzle, ensuring the product is pushed into the joint. For neat joints, use masking tape on both sides of the joint and remove it before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g., polyethylene backer rod) and appropriate joint width/depth. See the technical datasheet for more information. Limitations Not suitable on polyethylene, polypropylene, or Teflon. Cure excess product before disposal. Not for permanent water immersion or below water-line use. For water immersion, please use Selleys Marine Flex.
$23.92
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697115607.jpg?v=1754724130&width=645)
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Classic Cream]](http://gluesaustralia.com.au/cdn/shop/files/9300697122520.jpg?v=1754724130&width=645)
Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
$21.46
![Selleys No More Gaps Coloured Caulk Sealant 450g [Cream]](http://gluesaustralia.com.au/cdn/shop/files/9300697116307.png?v=1754724120&width=645)
No More Gaps Coloured Gaps No More Gaps Coloured Gaps offers a long-lasting, colour-matched finish, suitable for both interior and exterior use. It comes in a wide range of colours, with no need to paint over (although it is paintable if required). It provides superior flexibility to cope with building movement, hiding cracks and gaps longer, with greater than 350% elongation/stretch and up to +/- 20% movement capability. Key Features Long-lasting, colour-matched finish Suitable for Interior & Exterior use Available in a great colour range, with no need to paint over (Paintable if required) Superior flexibility to cope with building movement, hiding cracks and gaps longer Greater than 350% elongation/stretch and up to +/- 20% movement capability Good resistance to weathering Superior adhesion to a broad range of surfaces, resulting in a lasting finish Mould and mildew resistant Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles (not exposed to water) In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Bare or painted surfaces Colorbond Many other building materials How to Use Ensure the surface is clean, dry, and free from dust, grease, flaking/powdery paint, and old or crumbling caulk. Cut the seal and nozzle, fit it to the top of the cartridge, and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking Gun. Hold the caulking gun at a 45° angle and apply, forcing the product into the gap. Smooth with a wet finger or spatula. Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow surface to skin thoroughly prior to painting with water-based paints. If using oil-based paints or for large gaps, allow the sealant to set for about 24 hours and ensure the product is completely cured. Avoid water contact until fully cured – 72 hours or longer in cold weather. Limitations Not recommended for foot traffic areas, gaps between tongue and groove boards, or weatherboard overlaps. Use Selleys No More Gaps Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards, and Selleys No More Gaps Exterior & Weatherboard Gap Filler for weatherboard overlaps. Not suitable for areas in prolonged contact with water (e.g., showers, pools, & spas). Use Selleys Silicone Sealant for significant joint movement or areas of frequent water immersion. Do not apply or store below 5°C. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easier cleanup. When first applying, extrude a small amount onto scrap material to ensure smooth, continuous flow of gap filler. If wiping off excess with a wet finger, wet it with water (not saliva) to avoid bacteria that can promote mould growth. Allow surfaces to skin before painting, approximately 30 minutes. Protect from rain until the surface is firmly skinned. Some water-based undercoats and flat paints may crack when drying. To reduce this, allow the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting. Keep a pack of Selleys Sugar Soap Wipes handy for easy cleanup. Clean Up Water-based, so clean up with water. Uncured product may be removed with water. Cured product can be removed by sanding and scraping. Size 450g Cartridge Colours Black Brilliant White Brown Cedar Charcoal Coffee Cream Ivory Light Grey Technology Water-Based Use Interior & Exterior
$15.10
SikaSeal® Kitchen and Bathroom SikaSeal® Kitchen and Bathroom is a one-component, neutral-curing, low-odour silicone sealant with excellent adhesion and a long shelf life for DIY applications. It cures at room temperature under the action of atmospheric moisture to give a permanently flexible silicone rubber. Uses Glass and enamel Ceramics and tiles Aluminium, steel, zinc, copper Plastic laminates Rubber Stainless steel Concrete and grouts Characteristics / Advantages Excellent adhesion Great weatherability Non-sag Great tooling characteristics Long-term mould resistance Interior and exterior usage Fast curing Colours White Beige Black Charcoal Transparent Alabaster Almond Ivory Off White Stone Pewter Grey Mid Grey Stone Brown Packaging 300ml cartridges, 12 cartridges per box Shelf Life 12 months from the date of production if stored in undamaged and unopened original sealed containers, in dry conditions, and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base: Neutral curing Density: 0.98 g/cm³ @ 23ºC Skin/Forming Time: 10-15 minutes @ 23ºC/50% r.h. Curing Rate: 72 hours @ 23ºC/50% r.h. Consistency: Non-sag Mechanical/Physical Properties Tensile Strength: 0.4 N/mm² @ 23ºC/50% r.h. Shore A Hardness: 20 SHA E-Modulus: 0.30 N/mm² at 10% elongation @ 23ºC/50% r.h. Ultimate Elongation: 300% Anti-mildew Property: 0 level
$15.38
![MaxisiL A Silicone Sealant [Colour: A28 Brown]](http://gluesaustralia.com.au/cdn/shop/files/693_720.jpg?v=1754724110&width=645)
![MaxisiL A Silicone Sealant [Colour: A29 Havana]](http://gluesaustralia.com.au/cdn/shop/files/9326816000715.jpg?v=1754724111&width=645)
The Premium Wet Area Sealant Wet areas Baths, showers, toilets Easy to use Contains strong fungicides to fight mould Maxisil A Ceramic Silicone is an acetic cure silicone recommended for all ceramic tile areas, especially for expansion joints in bathrooms, kitchens, and flooring sectors. Built-in fungicides for mould resistance For both exterior and interior use Excellent weatherability, resistant to ageing and UV radiation Resistant to chemicals and temperature Primerless adhesion to clean, dry surfaces such as ceramics, glass, acrylics, aluminium, and painted wood Very good tooling and smoothing properties Time-saving with an easy cleanup system Please note that colour samples are not true to the actual colour. This is a guide only. Characteristics 1-component acetate-curing silicone sealant Excellent weathering, ageing, and UV resistance Enables a great finish, will not string during application Good tooling and smoothing properties Contains fungicides Medium skin formation time for easy handling Very good adhesion on ceramic substrates Primerless adhesion to many substrates Stress expansion modulus at 100% (DIN 53 504, S3A): 0.3 N/mm² Meets DIN 18545, part 2D (German industrial standard) Available in a variety of colours (custom colours available upon request) Fields of Application Sealing connection joints between ceramic tiles, showers, baths, and flooring sections Expansion/movement joints in bathrooms and wet areas Connection joints on door and window frames Sealing double-glazing joints Glass block glazing Sealing general building substrates Suitable for interior and exterior use Important Information Before application, ensure materials in the contact area are compatible with the sealant and with each other to prevent damage or discoloration. If in doubt, consult the manufacturers of surrounding substrates. While curing, small amounts of acetic acid are released — ensure good ventilation After curing, the product is odourless and harmless Thicker silicone layers require longer vulcanisation time Not for full-surface bonding unless construction prerequisites are met For layers over 15mm, contact our technical department Avoid contact with bitumen-containing materials or those releasing solvents (e.g. butyl, EPDM, neoprene, bituminous paints) When replacing mould-contaminated joints, remove all old sealant and treat areas with Maxisil Anti-Mildew Spray Technical Properties Skin-forming time (23°C / 50% RAH) ~ 15 min Curing in 24h (23°C / 50% RAH) ~ 2–3 mm Processing temperature +5°C to +35°C Viscosity (23°C) Pasty, stable Density (23°C, ISO 1183-1) ~ 1.0 g/cm³ Shore A hardness (ISO 868) ~ 20 Permissible movement capability —
$22.50
PROPERTIES Extra strong Fast but temporarily adjustable Does not drip Ideal for porous materials and vertical surfaces Dishwasher proof and water resistant APPLICATION SUITABLE FOR: Ideal for small-area bonds. Glues almost all solid and flexible materials like ceramics, leather, rubber, many plastics (such as rigid PVC, ABS, PS, Plexiglas®, polycarbonate (Makrolon®), and phenolic resins (Bakelite®)), porcelain, metal, wood, cork, felt, and cloth (check suitability first). Only partly suitable for glass (over a certain period of time the bond becomes brittle, causing it to weaken). Ideal for porous materials. NOT SUITABLE FOR: Not suitable for PE, PP, silicone resins, PTFE, Styrofoam®, fabrics and leather clothing. BEFORE USE: Working conditions Do not use at temperatures below +10 °C. The glue responds best to an air humidity level of 50-70 %. Surface requirements Surfaces to be glued must be clean, dry, and free of dust and grease, and must fit exactly. Preliminary surface treatment Any dust, oil, grease, wax or separating agent should be thoroughly removed from the surfaces to be stuck together. The best way to achieve this is to rub the parts a number of times with appropriate solvents, such as acetone (if suitable for the material – check first!). For metals and metal alloys it is usually sufficient to roughen the surface using emery paper or by grinding or brushing. DURING USE: Directions for use 1. To pierce the membrane, turn the cap clockwise firmly onto the tube. Tip: do not press the tube while piercing. 2. Unscrew the cap to reveal the applicator. Apply the adhesive directly from the tube, using the nozzle, as thinly as possible onto one side (too much glue slows down the curing process significantly). Press parts together immediately. After use, clean nozzle with a dry tissue and replace cap. Advice When glueing at low humidity, curing time can be shortened by briefly breathing onto one of the parts to be assembled. The best glueing results are reached at room temperature. Points of attention Contains cyanoacrylate. Bonds skin and eyelids together in seconds. If product comes into contact with the eyes, rinse immediately with plenty of water and seek medical advice. In case of contact with skin, glue can be dissolved by soaking in warm soapy water. Then apply a skin cream. May cause respiratory irritation. Avoid breathing vapours. Keep out of the reach of children. AFTER USE: Stains/residue Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue but very slowly (check suitability first). Storage conditions Store in a dry, cool, frost-free place. Storage below +5 °C (in refrigerator) ensures maximum shelf life.
$7.00
Super Glue gel's thick viscosity is perfect for clean, vertical, porous (wood, hard leather and porcelain) surfaces. Gels allow for a more accurate application as they do not drip or run. Works best on: Leather Metal Vinyl Rubber Most plastics Aluminum Ceramics Hard & Soft Wood China Pottery Jewelry NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rear view mirrors or parts that are subjected to great shock or continuous immersion in water. Properties: Initial color: Clear, transparent Final color: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820C) Use: NOTE: For best results, surfaces should be clean and dry and items should fit together well. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Carefully follow tube-opening directions on package. Unscrew cap while keeping tube pointed away from the face. 2. Apply to one surface, using 1 drop per square inch of surface. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe the top of nozzle if the adhesive has accumulated before recapping tube securely after use. Storage: Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$18.00
Our Quick Setting Gel Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product fills gaps and covers large porous surfaces. The final cure colour is cream but can be mixed with paint to colour match. This product sets in only 5 minutes. Works best on: • Porous materials • Ceramic • Metal • Pottery • Wood • Tile • Crafts Properties: Initial colour: Green resin/white hazy hardener Maximum Gap: .25” Final colour: White hazy Hardness, Shore D: 75-85 (After full cure) Set Time: 4-6 minutes @ 65-80F Shear Strength, Steel: 1500 psi (± 20%) Handling Time: After 1 hour Aluminum: 900 psi (± 20%) Full Strength: 24 hours Operating Temperature Range:-320 to 3000F (-360 to 1490C) Instructions: 1. Surfaces should be clean and dry, free from oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from container following package directions & mix thoroughly approximately 1 minute. Use package blister or clean cardboard for mixing container, do not use metal. 4. Apply to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F / 25C) with full cure in 24 hours. Helpful Hints: To colour Epoxy Gel, do test sample using mixed epoxy with added small amounts of colourant, such as paint (latex or oil), stain or tint. Mix well & apply to scrap piece of wood. Let dry to compare the final colour to the color of repair item. Keep testing until a colour match is achieved, then mix the appropriate amount of colourant with Epoxy Gel and bond repair item.
$9.95
This new, innovative dispensing system allows for accurate control while utilizing an advanced formula of the Super Glue Corporation's signature product cyanoacrylate (Super Glue GEL). The easy to hold applicator design allows for either continuous stream or single drop control. No more sticky fingers! This glue works great when adhering to porous or vertical surfaces. It will not drip or run! Works best on: Aluminum Ceramic China Hard & Soft Wood Jewelry Metal Most Plastics Pottery Rubber Vinyl Pacer Technology AccuTool Gel (19026) is a quick-setting, non-sagging gel adhesive that fills gaps & works best on: Leather Metal Vinyl Rubber Most plastics Aluminium Ceramics Hard & Soft Wood China Pottery Jewellery Fingernails NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rearview mirrors or parts that are subjected to great shock or continuous immersion in water. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800 F (-540 to 820C) Use: For best results, items should fit closely together. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Refer to package for special opening instructions – has Self Piercing “Ratchet” Opener. After opening, remove the outer cap for use. 2. Apply sparingly to one surface using 1 drop per square inch. Assemble parts and hold together with pressure for 15 seconds or until set. 3. After use, wipe tip before replacing cap to prevent sticking and close bottle securely. Storage and Shelf Life: Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause a burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$9.95
$15.00
SikaSeal®-401 Aquarium Premium one-component aquatic life safe silicone sealant SikaSeal® 401 Aquarium is a premium one-component room temperature vulcanising (RTV) silicone rubber that is safe for aquatic life and designed for sealing applications in aquariums, ponds and water pumps. It adheres very well to glass and aluminium, is UV resistant and has excellent gap filling properties. Extreme temperature resistance (-50°c to +250°c) Excellent vibration, UV and weathering resistance Good gap filling properties Usage Fish tanks Water pumps Aluminium Glass Advantages Extreme temperature resistance (-50°c to +250°c) Excellent vibration, UV and weathering resistance Good gap filling properties Highly versatile Easy to apply Aquarium safe Composition 1-C Silicone (acetoxy) Shelf life 18 months from date of production if in undamaged and unopened original sealed containers and stored according to the storage conditions. Storage conditions Must be stored in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Density ~1.02 kg/l Application Application steps SUBSTRATE PREPARATION Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue free solvent and allow to completely dry. CLEANING OF EQUIPMENT Uncured, excess SikaSeal® 401 Aquarium may be removed with Sika® Remover- 208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife. PRODUCT INFORMATION Composition 1-C Silicone (acetoxy) Packaging 75g Tube, 12 Tube per box Colour Clear Shelf life 18 months from date of production if in undamaged and unopened original sealed containers and stored according to the storage conditions. Storage conditions Must be stored in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Density ~1.02 kg/l Shore A Hardness ~23 Tensile Strength 1.0 N/mm2 Secant Tensile Modulus 1.1 n/mm2 Elongation at Break ~500% Ambient Air Temperature +5°c to +45°c Curing Rate ~3mm per 24 hours Skinning time ~7-10 minutes
$14.88
![Sika SikaSeal Flexible Gap Filler Super-200 Paintable [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/9318324010690_a135bef3-1e63-49fe-b52d-552f6c48153c.png?v=1754711651&width=645)
SikaSeal® Super-200 is great for sealing of connection joints with moderate movement Good UV resistance Low odour For exterior and interior use USE Sealing of connection joints with moderate movement around windows, window sills, doors, PVC pipes, dry partition walls and ceiling Filling of cracks on interior and exterior walls (with no permanent water immersion) CHARACTERISTICS AND ADVANTAGES For exterior and interior use High movement capability ±12.5% Good UV resistance Solvent-free, low odour Overpaintable Very good adhesion on most construction materials such as concrete, plaster, wood Possible storage at -10°C for short period of time (max 24h) Conforms to EN 15651-1 F INT EXT
$6.73
![Sika Sikaflex 252 High Strength Structural Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/7612895456188_c10ea96d-b0be-41ba-a0ee-9656fab35b16.jpg?v=1754711652&width=645)
Elastic adhesive for vehicle assembly bonding Sikaflex®-252 is an elastic 1-component polyurethane adhesive especially designed for bonding large components in vehicle assembly. It is suitable for bonding coated metal, GRP, ceramic materials and plastics. Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties PRODUCT BENEFITS Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties Can be painted Vibration-damping Electrically non-conductive Usage Sikaflex®-252 is suitable for assemblies that are subject to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminum (including anodized components), sheet steel (including phosphated, chromated and galvanized components), metal primers and paint coatings (2-component systems), ceramic materials and plastics. Seek manufacturer’s advice before using on plastics that are prone to stress cracking. This product is suitable for professional experienced users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
$53.62
Premium one component room temperature vulcanising silicone sealant USE Fridge and freezer sealing Pizza oven sealing Oven sealing Aluminium Glass CHARACTERISTICS AND ADVANTAGES High temperature resistance (-50 to 250OC) Excellent adhesion Gap filling properties Heat proof Vibration resistant Highly versatile PACKAGING: 300 ml cartridges COLOUR: Black SikaSeal® Appliance Silicone Sealant is a premium one component room temperature vulcanising (RTV) silicone rubber designed for flexible gasketing and sealing applications. SikaSeal® Appliance Silicone Sealant forms a tough but flexible seal of all shapes and sizes and fills any surface voids. The cured product can withstand vibration, weathering, temperature extremes, water oil and grease without hardening, shrinking or cracking. Uses Fridge and freezer sealing Pizza oven sealing Oven sealing Aluminium Glass Characteristics / Advantages High temperature resistance (-50 - 250°C) Excellent adhesion Heat proof Gap Filling properties Vibration resistant Highly versatile Product Data Colour Black Packaging 300ml Cartridge, 12 cartridges per box Storage 18 months from date of production if stored in undamaged and unopened original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base 1-C silicone Density (uncured) 1.0 kg/l approx. Skin Time 10 min approx. Tack-free time 20 min approx. Curing Time 24 hours approx. Cure Mechanism Moisture-curing Cure Type Acetoxy Application temperature 5 - 45°C Mechanical/Physical Properties Tensile Strength 1.0 N/mm2 approx. Shore a Hardness 25 approx. Ultimate Elongation 600% approx. Application Details Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue-free solvent and allowing drying properly. Cut the nozzle at a 45° angle to the desired bead size (3 mm is suitable for most applications) then apply a continuous and even bead along the joint. Cure Mechanism SikaSeal® Appliance cures by reaction with atmospheric moisture. The reaction thus starts at the surface and proceeds to the core of the joint. The curing speed depends on the relative humidity, temperature and thickness of the sealant. At low temperatures, the water content of the air is lower and the curing reaction proceeds more slowly. Clean Up Uncured, excess SikaSeal® Appliance may be removed with Sika® Remover-208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife. Application Conditions/ Limitations Restrictions On Use SikaSeal® Appliance is not recommended for use in applications where it will be permanently exposed to temperatures exceeding 250°C or in contact with fuels. The above information is offered for general guidance only.
$21.37
Sikaflex®-291 Tube Black: Marine-Grade, Multipurpose Polyurethane Sealant Product Benefits IMO Certified Bonds to a wide variety of substrates Good ageing and weathering resistance Elastic and low odour Non-corrosive, Overpaintable and Sandable Usage Sikaflex®-291 is a multipurpose product suitable for marine constructions. It is ideal for making elastic, vibration-resistant joint seals and can also be used for interior sealing applications. Application Information Surface preparation is key. Surfaces must be clean, dry and free from grease, oil, and dust. Further application tips can be found in the Sika Pre-treatment Chart for Marine Applications. Additional Details Application Temperature: 5 ? 40 °C Skin Time: 60 minutes Shore A Hardness: 40 Shelf Life: 12 months when stored below 25°C
$17.76
Sikaflex®-111 Stick & Seal Grey: The Multipurpose Adhesive & Sealant Product Overview Experience the versatility of Sikaflex®-111 Stick & Seal, a 1-part adhesive and sealant that caters to both internal and external projects. Key Advantages Bonds to a plethora of substrates without the need for surface pre-treatment Excellent adhesion to damp concrete Compatible with a multitude of construction materials Strong mechanical and weathering resistance CE Marking for quality assurance Usage Sikaflex®-111 is perfect for bonding and sealing the following materials: Concrete Masonry Most stones Ceramic Wood Metal Glass Various Plastics Packaging Available in 290 ml cartridges, 12 per box. Color Options Choose from White, Concrete Grey, or Black to match your project requirements. Application Instructions Ensure the substrate is clean and free of contaminants for optimum adhesion. For detailed application instructions, please contact Sika Technical Services.
$25.02
Sikaflex®-111 Stick & Seal Black: Seal, Bond, and Build with Ease Product Overview The one-stop solution for all your adhesive and sealing needsSikaflex®-111 Stick & Seal Black. Advantages Bonds effortlessly to a myriad of substrates with no surface pre-treatment needed Excellent for use on damp concrete Fully compatible with most construction materials Durable against weathering and mechanical wear CE Marked for quality assurance Usage Scenarios This versatile product is perfect for: Concrete Masonry Stones Ceramic Wood Metal Glass Plastics including PVC, PA, PET, and EPS/XPS Packaging Available in 290 ml cartridges, packed 12 cartridges per box. Color Options Also available in White and Concrete Grey. Application Guidelines For best results, the substrate should be free of contaminants. Further instructions for both porous and non-porous substrates are available. Cleaning & Maintenance Use Sika® Remover-208 for cleaning tools and Sika® Cleaning Wipes for skin.
$25.02
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524002800_e901daee-d941-4c51-bb2c-fdfedd9a6316.jpg?v=1754711662&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$27.48
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$27.48
One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces 100% crystal clear / transparent Good workability Very good adhesion on many typical building materials Use: Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including: Plasterboard Wood surfaces Painted enamel Polyester Plastic Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions. CHARACTERISTICS AND ADVANTAGES 100% crystal clear / transparent Good workability Low shrinkage during cure Flexible and elastic Can be used on damp concrete Very good adhesion on many typical building materials COLOUR: Transparent Product Data Appearance / Colours Transparent Packaging 300 g cartridge (290 ml), 12 cartridges per box Storage Conditions / Shelf-Life Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met. Technical Data Chemical Base Silane terminated polymer Density 1.05 kg/l approx. (ISO 1183-1) Tensile Strength 2.0 N/mm2 approx. (ISO 37) Shore A Hardness 30 approx. (after 28 days) (ISO 868) Elongation at Break 400% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Service Temperature −40 °C to +70 °C SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department. Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly. Bonding After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again. Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear. Sealing After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.
$27.65
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$27.72
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$27.72
SikaBond Fast is a premium, water-based, multi-purpose construction adhesive providing strong initial grab and high bond strength. Uses: SikaBond Fast can be used on most substrates due to its excellent adhesion. These include: - Fixing polystyrene wall panels - Replacing loose tiles on walls - Skirting boards, architraves and trims to walls - Bonding panels to wall studs - Bonding particleboard, plywood, fibre cement and strip flooring to joists Advantages : - Complies to AS2329-1980, “Mastic Adhesives for Fixing Wallboards” - Natural wood colour - Reduces the number of mechanical fasteners required to install floors or walls. - Can be repositioned for up to 60 minutes after application - Reduces squeaking associated with nail ride in floors - Paintable with water-based surface coatings - Easy to use one component - Bridges gaps up to 9 mm - Strong adhesion to metal - No fumes - High bond strength and heat resistance - Flows easily at all temperatures - Easy cleanup - Fast initial grab – minimises slippage on vertical surfaces Storage and Shelf Life Stored in the original sealed packaging at temperatures of between 5oC and 35oC, this material will keep for at least two (2) years. Instructions for Use Surface Preparation All surfaces must be clean, sound, dry and free of oil, grease and surface contamination. Thoroughly remove all loose particles and dust. Any loose flaking material must be removed and light sanding is recommended. SikaBond Fast will adhere to damp (not wet) substrates but drying times may increase. Substrates should be above 5ºC. Do not bond 2 non-porous substrates ensure that one surface is porous. Application Apply a 5 mm bead of SikaBond Fast to one surface using a cartridge gun; ensure the beads are no more than 45cm apart. Bring both substrates immediately together and clamp, nail or screw for a minimum of 24 hours. For butt joints use adhesive on both panel edges. Cleaning The uncured material can be cleaned with water. The hardened material can only be removed by mechanical means. Technical Data (Typical) Colour Pale Brown Specific Gravity ~ 1.4 Skinning Time 20 minutes Repositioning Time 60 minutes Full Cure 24 hours depending on conditions When both surfaces are porous firm, a slip-resistant bond will develop after 15 minutes at 30ºC and 60 minutes at 10ºC. Should one surface be non-porous or the substrate damp, a firm slip resistant bond will be achieved in approximately 8 hours. After 24 hours, 90% of the final strength will be achieved. (dependant on temperature, the porosity of the substrates, humidity and ventilation). Service temperature -5ºC to +90ºC Packaging 420 gram cartridge (12 cartridges per box)
$8.69
SikaTitan® 258 is a primerless to windscreen, one-component direct glazing adhesive. It is easy to apply and has a paste-like consistency. On exposure to atmospheric moisture it cures to a durable elastomer. SikaTitan® -258 provides a long tack-free time and ensures a safe application even under warm conditions. Note: Primerless application requires the glass to be prepared with a non-antistatic glass cleaner. Also the bonding surfaces must be free of contamination prior to the application of the adhesive. SikaTitan® -258 is manufactured in accordance with ISO 9001 / 14001 quality assurance system and with the responsible care program. Product Benefits - Primerless to glass - One-component formulation - Cold application - Good application properties such as bead stability / good non-sag properties - Short cut-off string - Tested according to FMVSS 212/208 (with double-side airbags, no seatbelts) Areas of Application SikaTitan® -258 is suitable for direct-glazing applications in the Automotive Glass Replacement business. With its good performance and application properties it is suitable for mobile as well as inhouse installations.This product is to be used by professional experienced fitters only. If this product is used for other applications than Automotive Glass Replacement, trials must be carried out prior to use. Technical Product Data Chemical base 1-C polyurethane Colour (CQP1) 001-1) Black Cure mechanism Moisture-curing Density (uncured) (CQP 006-4) 1.1 kg/l approx. Non-sag properties (CQP 061-1) Good Application temperature +5 to +40°C Skin time2) (CQP 019-1) 40min. approx. Open time2) (CQP 526-1) 30min. approx. Curing speed(CQP 049-1) Shore A hardness (CQP 023-1 / ISO 868) 51 approx. Tensile strength (CQP 036-1 / ISO 37) 5 MPa approx. Elongation at break (CQP 036-1 / ISO 37) 650% approx. Tensile lap-shear strength (CQP 046-1 / ISO 4587) 2.5 MPa approx. Safe Drive-Away Time2) (cars) with double side airbag according to FMVSS 212 / 208 (CQP 511-1) without airbag 6 hours 2 hours Chemical Resistance SikaTitan® -258 is resistant to fresh water, seawater, limewater, sewage effluent, diluted acids and caustic solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic acids and caustic solutions or solvents. Method of Application Removal of old glass Remove damaged glass in accordance with the vehicle manufacturer’s instructions. Surface preparation Surfaces must be clean, dry and free from dust and grease. The bond faces must be prepared with a non-antistatic glass cleaner. Bonding surface must be free of contaminants before application of the product. Windshields without ceramic coatings need additional UV protection. Application Cut off the tip of the nozzle in accordance with the vehicle manufacturer's recommendations and screw onto the cartridge. It is recommended to apply the adhesive with a piston-type application gun. To ensure a uniform thickness of adhesive bead, we recommend that the adhesive be applied in the form of a triangular bead (see fig. 1 below). The substrate temperature must be between 5°C and 35°C.
$43.58
![Sika Sikasil Pool Silicone Water Resistance [White]](http://gluesaustralia.com.au/cdn/shop/files/7612894609400_e5cdedf3-65af-430d-be37-52c0a1c7ff7a.png?v=1754711689&width=645)
$28.10
![Sika Sikasil Pool Silicone Water Resistance [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/76128946_314287d6-23cc-4ab5-90d4-1c020429de31.png?v=1754711691&width=645)
$21.96
SIKASIL® POOL | JOINT SEALANT - Ultra premium, high chemical resistant silicone sealant - Highest chemical resistant silicone in the range - Suitable for full immersion in chlorinated water once cured - Excellent UV and fungal resistance and high flexibility after cure USE Sikasil® Pool is suitable for joints in and around swimming pools, areas under permanent water immersion and frequently wet areas, such as shower rooms in sports halls or leisure facilities, between ceramics, tiles, concrete, glass, metals and other typical building substrates, etc. CHARACTERISTICS AND ADVANTAGES Very high water resistance High chlorine resistance (as required in swimming pools due to use of disinfecting solutions) Extremely high resistance to fungal attack Excellent UV and weathering resistance High tear resistance Non-corrosive High elasticity and flexibility COLOUR: Transparent PRODUCT INFORMATION Composition Neutral cure silicone Shelf life Sikasil® Pool has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met. Storage conditions Sikasil® Pool shall be stored in dry conditions, protected from direct sunlight and at temperatures between +5 °C and +25 °C. Density ~1.05 kg/l TECHNICAL INFORMATION Shore A Hardness ~20 (after 28 days) (ISO 868) Tensile Strength ~1.5 N/mm2 (ISO 8339) Secant Tensile Modulus ~0.30 N/mm2 at 100 % elongation (23 °C) (ISO 8339) Elastic Recovery > 90 % (ISO 7389) Tear Propagation Resistance ~4.0 N/mm (ISO 34) Movement Capability ± 25 % (ISO 9047) Service Temperature −40 °C to +80 °C Joint Design The joint width must be designed to suit the joint movement required and the movement capability of the sealant. The joint width shall be ≥ 10 mm. Sikasil® Pool shall not be used on joints with widths > 15 mm and depths or thicknesses < 6 mm. For larger joints please contact Sika Technical Service. Backing Material Use closed cell, polyethylene foam backing rods. Sag Flow < 2 mm (20 mm profile, 23 °C) (ISO 7390) Ambient Air Temperature +5 °C min. / +40 °C max. Substrate Temperature +5 °C min. / +40 °C max. min. 3 °C above dew point temperature Curing Rate ~2.0 mm/24 h (23 °C / 50 % r.h.) (CQP 049-2) Skinning time ~5 min (23 °C / 50 % r.h.) (CQP 019-1) APPLICATION INSTRUCTIONS SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikasil® Pool adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, glass, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, must also be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30 minutes (< 8 hours) before sealing the joints. PVC has to be cleaned and pre-treated using Sika® Primer-215 applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours). Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours). For more detailed advice and instructions please contact the local Sika Technical Services Department. Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly. APPLICATION METHOD / TOOLS Sikasil® Pool is supplied ready to use. After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a foil pack or cartridge into the sealant gun and extrude Sikasil® Pool into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikasil® Pool sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Use a compatible tooling agent (e.g. Sika® Tooling Agent N) to smooth the joint surfaces. Do not use tooling products containing solvents. CLEANING OF EQUIPMENT Clean all tools and application equipment immediately after use with Sika® Remover-208. Once cured the residual material can only be removed mechanically. IMPORTANT CONSIDERATIONS ▪ Sikasil® Pool cannot be overpainted. Colour variations may occur due to exposure to chemicals, high temperatures and/or UV-radiation (especially with the colour shade white). However, a change in colour is purely of aesthetic nature and does not adversely influence the technical performance or durability of the product. ▪ The use of non-prescribed tooling agents must be tested prior to use in application to ensure they will not cause aesthetical changes (such as discolouration). ▪ Do not use Sikasil® Pool on bituminous substrates, natural rubber, EPDM rubber or on any building materials which might bleed oils, plasticizers or solvents that could attack the sealant. ▪ Do not use Sikasil® Pool for structural glazing or insulated glazing, and food contact applications. ▪ Do not use Sikasil® Pool for medical or pharmaceutical uses. ▪ Before using Sikasil® Pool on natural stone, please contact our Technical Service Department for advice. ▪ Recommendations for use in swimming pools / warm water whirlpools: Allow Sikasil® Pool to cure completely before the filling of the pool; minimum of 7 days (depending on the temperature, humidity and thickness of the sealant applied). ▪ The resistance of a sealant to chlorine is dependent on the pH value of the water and the amount of free chlorine. ▪ Sikasil® Pool can be used in swimming pools and warm water whirlpools in which a pH value between 6.5 and 7.6 is maintained, and the free chlorine remains less than 5 mg/l (5 ppm). ▪ To reduce the risk of fungal attack on Sikasil® Pool, the free available chlorine level shall not be ≤ 0.3 mg/l in swimming pools and ≤ 0.7 mg/l in warm water whirlpools. Continuous water circulation is required to avoid chlorine concentrations. ▪ If there is a very strong smell of chlorine, check the pH value accordingly. ▪ Do not use acid-based detergents as they increase the danger of fungal attack. ▪ When joints are reconstructed due to fungal attack, Sikasil® Pool must be removed completely. BASIS OF PRODUCT DATA All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
$21.96
![Sika Sikasil 670 Fire Resistant Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/7612895181462_fe2d5a8d-2a66-433f-9d24-2dfa9adec11a.jpg?v=1754711694&width=645)
SIKASIL® -670 FIRE | JOINT SEALANT Fire-rated joint sealant Up to 4 hours fire resistance according to EN 1366-4 Very good resistance to weathering Easy to smooth and very good workability DESCRIPTION Sikasil®-670 Fire is a fire-rated, 1-component, moisture-curing, low-modulus elastic joint sealant. USES Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates. CHARACTERISTICS / ADVANTAGES ▪ Up to 4 hours fire resistance according to EN 1366-4 ▪ Very good resistance to weathering ▪ Movement capability of ± 35% (ASTM C 719) ▪ Easy to smooth and very good workability ▪ Good adhesion to many different substrates ▪ Neutral curing ENVIRONMENTAL INFORMATION ▪ LEED® EQc 4.1 ▪ SCAQMD, Rule 1168 ▪ BAAQMD, Reg. 8, Rule 51 APPROVALS / STANDARDS ▪ EN 15651-1 F EXT-INT CC 25 LM ▪ EN 15651-4 PW INT ▪ ISO 11600 F 25 LM & G 25 LM ▪ ASTM C 920, class 35 ▪ EN 1366-4 assessment report ▪ ETAG 026 assessment report ▪ EN 13501-2 classification report ▪ EN 140-3 ▪ EN 13501-1 class B-s2-d0 PRODUCT INFORMATION Chemical Base Neutral cure silicone Colour: Grey Storage Conditions Sikasil®-670 Fire shall be stored in dry conditions, where it is protected from direct sunlight and at temperatures between +5 °C and +25 °C. Density 1.35 kg/l approx. (ISO 1183-1) TECHNICAL INFORMATION Shore A Hardness 16 approx. (after 28 days) (ISO 868) Secant Tensile Modulus 0.30 N/mm2 approx. at 100% elongation (23 °C) (ISO 8339) 0.50 N/mm2 approx. at 100% elongation (−20 °C) Elongation at Break 650% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Movement Capability ±25% (ISO 9047) ±35% (ASTM C 719) Service Temperature −40 °C to +150 °C Joint Design The joint width must be designed to suit the joint movement required and the movement capability of the sealant. The joint width shall be ≥ 10 mm and ≤ 40 mm. The joint depth shall be ≤ 20 mm. A width to depth ratio of 2:1 must be maintained (for exceptions, see table below). Backing Material Use polyethylene foam backing rods. Sag Flow 2 mm approx. (20 mm profile, 50 °C) (ISO 7390) Ambient Air Temperature +5 °C to +40 °C, min. 3 °C above dew point temperature Substrate Temperature +5 °C to +40 °C Curing Rate 2 mm/24 hours approx. (23 °C / 50% r.h.) (CQP 049-2) Skin Time 25 minutes approx. (23 °C / 50% r.h.) (CQP 019-1) Tooling Time 20 minutes approx. (23 °C / 50% r.h.) (CQP 019-2) APPLICATION INSTRUCTIONS SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikasil®-670 Fire adheres without primers and/or activators APPLICATION METHOD / TOOLS Sikasil®-670 Fire is supplied ready to use. After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a foil pack or cartridge into the sealant gun and extrude Sikasil®-670 Fire into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikasil®-670 Fire sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. CLEANING OF TOOLS Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® TopClean T. Once cured, residual material can only be removed mechanically. FURTHER DOCUMENTS ▪ Safety Data Sheet (SDS) ▪ EN 13501-2 classification report ▪ ETAG 026 assessment report ▪ Brochure Sika Fire Protection Solutions LIMITATIONS ▪ Sikasil®-670 Fire cannot be overpainted. Colour variations may occur due to exposure to chemicals, high temperatures and/or UV-radiation (especially with the colour shade white). However, a change in colour is purely of aesthetic nature and does not adversely influence the technical performance or durability of the product. ▪ Do not use Sikasil®-670 Fire on natural stone. Do not use Sikasil®-670 Fire on bituminous substrates, natural rubber, EPDM rubber or on any building materials which might bleed oils, plasticizers or solvents that could attack the sealant. ▪ Do not use Sikasil®-670 Fire to seal joints in and around swimming pools. ▪ Do not use Sikasil®-670 Fire for joints under water pressure or for permanent water immersion. ▪ Do not expose uncured Sikasil®-670 Fire to alcohol-containing products as this may interfere with the curing reaction.
$22.15
![Sika SikaSil 670 Fire Rated Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324012236_d7a5d83c-0ea4-4a46-88bb-55e873bf5a05.jpg?v=1754711696&width=645)
Usage Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates. Advantages Up to 4 hours fire resistance according to AS 1530.4 Up to 4 hours fire resistance according to EN 1366-4 Very good resistance to weathering Movement capability of ± 35% (ASTM C 719) Easy to smooth and very good workability Good adhesion to many different substrates Neutral curing Colour Grey
$27.35
![Sika SikaSeal Gap Filler Acrylic 100 Sandable Paintable [White]](http://gluesaustralia.com.au/cdn/shop/files/9318324010676_f8ac62bc-ef55-4a57-a739-47528a1aae8c.jpg?v=1754711697&width=645)
DESCRIPTION SikaSeal® Acrylic 100 is a flexible, one component, water based acrylic joint sealant and gap filler where low demand of elongation are required, for interior use. USES SikaSeal® Acrylic 100 is suitable for sealing low movement joints around: ? brick ? Concrete ? Plasterboard ? Windows ? Doors ? Ceramic tiles SikaSeal® Acrylic 100 fills cracks and adheres to: ? Glass ? Wood ? Aluminium ? Brick ? Concrete ? Plasterboard ? Ceramic ? Painted surfaces. CHARACTERISTICS / ADVANTAGES Excellent adhesion to most common construction materials. Water clean-up of uncured sealant. Can be sanded back once fully cured if required to give smooth surface finish. Can be painted over using water based paints. Non-toxic
$5.04
![Sika SikaSeal 300 Glass & Weather Seal [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/9318324011314_17b1b8c7-fa52-428b-bf6f-872b3b964d3b.png?v=1754711699&width=645)
Usage Aluminium Composite materials Panels(ACP) Glass Metals Coated and painted metals Plastics Wood Advantages Excellent adhesion High movement capability Weather resistant Outstanding UV resistance High strength Interior & Exterior Permanent flexibility Colour Transparent
$18.18
Sikaflex®-111 Stick & Seal White: The Multipurpose Adhesive & Sealant Product Overview Experience the versatility of Sikaflex®-111 Stick & Seal, a 1-part adhesive and sealant that caters to both internal and external projects. Key Advantages Bonds to a plethora of substrates without the need for surface pre-treatment Excellent adhesion to damp concrete Compatible with a multitude of construction materials Strong mechanical and weathering resistance CE Marking for quality assurance Usage Sikaflex®-111 is perfect for bonding and sealing the following materials: Concrete Masonry Most stones Ceramic Wood Metal Glass Various Plastics Packaging Available in 290 ml cartridges, 12 per box. Application Instructions Ensure the substrate is clean and free of contaminants for optimum adhesion. For detailed application instructions, please contact Sika Technical Services.
$25.02
![Sika Sikaflex 291 Marine Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb9d6399-3f9c-4c6e-aeb9-97604f6829a6.jpg?v=1754711703&width=645)
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck. Why Choose Sikaflex®-291 Excellent adhesion to common marine substrates Good ageing & weathering resistance for long service life Elastic to absorb vibration and movement Low odour and non-corrosive Overpaintable and sandable after cure* Available colours: White, Grey, Black *Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area. Typical Uses Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications. Suitable Substrates Wood Metals, metal primers and 2-component paint systems Ceramic materials Plastics such as GRP (fibreglass), etc. Do Not Use On Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate) Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility. Technical Data (Typical) Property Method / Note Value Chemical base — 1-component polyurethane Cure mechanism — Moisture-curing Colour CQP001-1 White, Grey, Black Density (uncured) — ~1.3 kg/L (colour-dependent) Non-sag properties — Good Application temperature Ambient 5 – 40 °C (optimum 15 – 25 °C) Skin time CQP019-1 (A) ~60 minutes Open time CQP526-1 (A) ~45 minutes Curing speed CQP049-1 Depends on temperature & humidity (see TDS) Shrinkage CQP014-1 ~5 % Shore A hardness CQP023-1 / ISO 48-4 ~40 Tensile strength CQP036-1 / ISO 527 ~1.8 MPa Elongation at break CQP036-1 / ISO 527 ~500 % Tear resistance CQP045-1 / ISO 34 ~6 N/mm Service temperature (continuous) CQP513-1 −50 to +90 °C Service temperature (short-term) CQP513-1 +160 °C (4 h), +180 °C (1 h) Shelf life (B) 12 months (store < 25 °C) CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C. Application Guidance Surface Preparation Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates. Application Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity. Optimum substrate and product temperature is 15 – 25 °C. Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment. Tooling & Finishing Tool within the skin time. Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability). Cleaning & Removal Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent. Cured material: remove mechanically (e.g. knife, wire, abrasion). Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin. Overpainting Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting. If the paint requires baking > 80 °C, allow the sealant to fully cure first. Always conduct preliminary trials under manufacturing conditions. Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area. Compliance & Approvals Meets requirements set out by the International Maritime Organization (IMO). Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable. FAQs Can Sikaflex®-291 be overpainted? Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area. What is a “marine grade” sealant/adhesive? Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline. When and why should a primer be used? Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing. What does the Wheelmark indicate? The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED). Which substrates does Sikaflex®-291 bond to? Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate). How do I remove Sikaflex®-291? Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material. Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
$28.97
![Sika Sikaflex 291 Marine Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb4dfb0d-a336-4739-9b91-9ca89764b874.jpg?v=1754711704&width=645)
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck. Why Choose Sikaflex®-291 Excellent adhesion to common marine substrates Good ageing & weathering resistance for long service life Elastic to absorb vibration and movement Low odour and non-corrosive Overpaintable and sandable after cure* Available colours: White, Grey, Black *Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area. Typical Uses Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications. Suitable Substrates Wood Metals, metal primers and 2-component paint systems Ceramic materials Plastics such as GRP (fibreglass), etc. Do Not Use On Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate) Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility. Technical Data (Typical) Property Method / Note Value Chemical base — 1-component polyurethane Cure mechanism — Moisture-curing Colour CQP001-1 White, Grey, Black Density (uncured) — ~1.3 kg/L (colour-dependent) Non-sag properties — Good Application temperature Ambient 5 – 40 °C (optimum 15 – 25 °C) Skin time CQP019-1 (A) ~60 minutes Open time CQP526-1 (A) ~45 minutes Curing speed CQP049-1 Depends on temperature & humidity (see TDS) Shrinkage CQP014-1 ~5 % Shore A hardness CQP023-1 / ISO 48-4 ~40 Tensile strength CQP036-1 / ISO 527 ~1.8 MPa Elongation at break CQP036-1 / ISO 527 ~500 % Tear resistance CQP045-1 / ISO 34 ~6 N/mm Service temperature (continuous) CQP513-1 −50 to +90 °C Service temperature (short-term) CQP513-1 +160 °C (4 h), +180 °C (1 h) Shelf life (B) 12 months (store < 25 °C) CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C. Application Guidance Surface Preparation Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates. Application Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity. Optimum substrate and product temperature is 15 – 25 °C. Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment. Tooling & Finishing Tool within the skin time. Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability). Cleaning & Removal Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent. Cured material: remove mechanically (e.g. knife, wire, abrasion). Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin. Overpainting Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting. If the paint requires baking > 80 °C, allow the sealant to fully cure first. Always conduct preliminary trials under manufacturing conditions. Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area. Compliance & Approvals Meets requirements set out by the International Maritime Organization (IMO). Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable. FAQs Can Sikaflex®-291 be overpainted? Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area. What is a “marine grade” sealant/adhesive? Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline. When and why should a primer be used? Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing. What does the Wheelmark indicate? The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED). Which substrates does Sikaflex®-291 bond to? Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate). How do I remove Sikaflex®-291? Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material. Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
$28.97
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895456164_5c293f0a-df90-415e-875b-0ed963018cfa.jpg?v=1754711706&width=645)
High strength, structural grade polyurethane adhesive sealant High strength elastic adhesive, suitable for structural joints subjected to high dynamic stress Suitable for use on trucks, trailers and caravans with excellent adhesion to timber, metals, primers and paint coatings Vibration dampening USE Sikaflex® 252 is suitable for structural joints that will be subjected to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminium (incl. anodized components), sheet steel (incl. phosphated, chromated and zinc-plated components), metal primers and paint coatings (2-c systems), ceramic materials and plastics. CHARACTERISTICS AND ADVANTAGES 1-C formulation Elastic Can be overpainted Good gap-filling properties Capable of withstanding high dynamic stresses Vibration Damping Non-corrosive Electrically non-conductive Bonds well to a wide variety of substrates
$53.62
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524003593_20527af7-fe08-426c-ab91-1e7cb16de683.png?v=1754711708&width=645)
Multi-purpose adhesive sealant with a wide adhesion range Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals. Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted PRODUCT BENEFITS Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted Passes EN45545-2 R1/R7 HL3 Non-corrosive Low odour NSF-approved for incidental food contact Potable water approved (meets AS4020 requirements) Usage Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Surface preparation Surfaces must be clean, dry and free from grease, oil and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry. Tooling and finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use. Removal Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin. Overpainting Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
$38.04
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003395_211a040d-fd65-46e4-b320-62196c5157c2.png?v=1754711709&width=645)
Multi-purpose adhesive sealant with a wide adhesion range Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals. Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted PRODUCT BENEFITS Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted Passes EN45545-2 R1/R7 HL3 Non-corrosive Low odour NSF-approved for incidental food contact Potable water approved (meets AS4020 requirements) Usage Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Surface preparation Surfaces must be clean, dry and free from grease, oil and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry. Tooling and finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use. Removal Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin. Overpainting Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
$38.04
![Sika Sikaflex 118 Extreme Grab 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895530055_35bcc6bf-bbee-4219-b850-30fa7a6b83ac.png?v=1754711711&width=645)
Sikaflex®-118 Extreme Grab is a 1- part construction adhesive with very high initial grab which bonds most construction material substrates. Internal and external use. Very high initial grab Fixing of heavy objects without temporary fixation Good workability Usage An adhesive to bond most construction components and materials such as: Concrete Masonry Most stones Ceramic Wood Metals Glass Mirrors* Advantages Very high initial grab Fixing of heavy objects without temporary fixation Good workability Very low emissions Adhesive-sealant with CE marking Packaging 290 ml cartridge, 12 cartridges per box Colour White Composition Silane terminated polymer Storage conditions The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +25 °C. Always refer to packaging. Density ~1.40 kg/l Technical Information Shore A hardness ~50 (after 28 d) Tensile strength ~2.2 N/mm2 Tear propagation resistance ~10.0 N/mm Service temperature −40 °C min. / +80 °C max. SUBSTRATE PREPARATION The substrate must be sound, clean, dry and free of all contaminants such as dirt, oil, grease, cement laitance, old sealants and poorly bonded paint coatings which could affect adhesion of the adhesive. For optimum adhesion and critical, high performance applications the following priming and/or pre-treatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, galvanised steel, powder coated metals or glazed tiles, slightly roughen surface with a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Before bonding / sealing, allow a waiting time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. After a waiting time of > 15 minutes (< 6 hours). Apply Sika® Primer-3 N applied by brush. Allow a further waiting time of > 30 minutes (< 8 hours) before bonding / sealing. PVC has to be cleaned and pre-treated using Sika® Primer-215 applied with a brush. Allow a waiting time of > 15 minutes (< 8 hours) before bonding / sealing. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks, prime surface using Sika® Primer-3 N applied by brush. Before bonding / sealing, allow a waiting time of > 30 minutes (< 8 hours). For more detailed advice and instructions contact Sika Technical Services. Note: Primers are adhesion promoters and not an alternative to improve poor preparation / cleaning of joint surfaces. Primers also improve the long term adhesion performance of a sealed joint. CLEANING OF EQUIPMENT Clean all tools and application equipment immediately after use with Sika® Remover-208. Once cured, hardened material can only be removed mechanically. For cleaning skin use Sika® Hand Wipes.
$25.60
SikaBond®-145 SuperGrip Premium polyurethane construction adhesive with fast build up of Strength SikaBond®-145 SuperGrip is a premium grade one-component polyurethane construction adhesive with good initial grab and high strength after 30 minutes^. SikaBond®-145 SuperGrip is a versatile, ready to use, fast curing, general purpose construction adhesive suitable for interior and exterior use. One-component. Interior & exterior. Non-shrink. Usage SikaBond®-145 SuperGrip is suitable for use in construction and repair applications where a permanent strong bond is required between porous-nonporous surfaces. SikaBond®-145 SuperGrip is suitable for bonding most common construction materials such as: Wood MDF Concrete Brick Metal Polystrene Polyurethane foam Some PVC Marble Granite Ceramic LOSP Timber Advantages One-component. Interior & exterior. Non-shrink. Non-sag. High initial grab. Adheres rapidly. Stong bond in 30 minutes^. Fast cure. Solvent-free. Resistant to heat. Resistant to weathering. Water resistant -D4 according to DIN En 204 Applies white, can dry translucent if applied in thin layers.
$24.15
Sika MaxTack® 100g: Secure Your Projects with Unmatched Initial Grab Product Overview Sika MaxTack® 100g is a high-strength, solvent-free adhesive with incredible initial tack. Advantages High initial tack and powerful grab Secure bonding without the need for tapes, nails, or screws Excellent workability and over-paintable with water-based paints Perfect for both interior and sheltered outdoor use Applications Designed for the bonding of: Skirting boards, wood frames, and panels Anodised aluminum and hard PVC profiles Polystyrene mouldings, ceiling tiles, and more Packaging Available in 100g foil packs, 24 packs per box. Color Options Off-white in color. Application Instructions Ensure the substrate is clean and dry. For best results, follow our standard construction guidelines. Cleaning & Maintenance Clean tools immediately after use with water. Hardened material can only be removed mechanically.
$11.47
Sika Firerate is a gunnable acrylic based jointing and sealing compound specially formulated with inorganic fillers to provide a fire barrier. Sika Firerate has been tested for fire resistance for up to 4 hours according to AS 1530.4 in masonry wall and floor joints. USE Sika Firerate is suitable for sealing joints in concrete or masonry that must have a fire rated resistance to Australian Standards. Sika Firerate also fulfils the basic function of a gap filler and joint sealant against water and dust penetration. CHARACTERISTICS AND ADVANTAGES Safe to use – contains no asbestos or fibres. Paintable. Good flexibility and adhesion to concrete and masonry. Interior use only. Easily applied with normal caulking equipment. Easy tooling off. Economical – single product for both fireproofing and sealing functions. Water clean-up of tools and equipment while still uncured. Excellent acoustic performance, test report available. COLOUR Grey CHARACTERISTICS/ADVANTAGES • Up to 4 hours fire resistance according to AS 1530.4 • Very good resistance to weathering • Movement capability of ± 20 % • Easy to smooth and very good workability • Good adhesion to many different substrates • Water clean-up of uncured sealant . APPROVALS / STANDARDS • AS 1530.4 FRL • ISO 717.2 Rw (Ctr) = 64 (-13) SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sika® Firerate adheres without primers and/or activators. APPLICATION METHOD / TOOLS Sika® Firerate is supplied ready to use. After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a foil pack or cartridge into the sealant gun and extrude Sika® Firerate into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sika® Firerate sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Water can be used if wet tooling is required. CLEANING OF TOOLS Clean all tools and application equipment immediately after use with water. Once cured, residual material can only be removed mechanically LIMITATIONS • Sika® Firerate may be overpainted with solvent free paints. • Do not use Sika® Firerate on damp and/or wet substrates. • Do not apply Sika Firerate at temperatures below 5ºC • Do not use Sika® Firerate to seal joints in and around swimming pools. • Do not use Sika® Firerate to seal joints in external applications on non-porous substrates. • Do not use Sika® Firerate for joints under water pressure or for permanent water immersion. • Do not expose uncured Sika® Firerate to rain or water as this may interfere with the curing reaction. BASIS OF PRODUCT DATA All technical data stated in this Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control. ECOLOGY, HEALTH AND SAFETY For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Safety Data Sheet (SDS) containing physical, ecological, toxicological and other safety related data.
$25.69
Sika® Filler One Strike Maxi is revolutionary ready-mixed lightweight filler for the preparation of numerous surfaces prior to painting or wallpapering. For filling on plaster, brick, stone, wood and render. Fills in one go- No need to build up layers of filler – fills up to 75mm deep in one application No sanding or sagging Fast drying and easy to sand CHARACTERISTICS AND ADVANTAGES Fills in one go- No need to build up layers of filler – fills up to 75mm deep in one application No sanding or sagging Fast drying and easy to sand Internal/external use Overpaintable Overstainable Easy to use Dries brilliant white COLOUR: White Sika® Filler One Strike is revolutionary ready-mixed lightweight filler for the preparation of numerous surfaces prior to painting or wallpapering. Based on high strength lightweight polymeric fillers, the product outperforms conventional fillers in most applications Designed for professional and D.I.Y use. Uses Sika® Filler One Strike 1 is suitable for filling of gap in: Plaster Brick Stone Wood Render Characteristics Advantages Fills in one go- No need to build up layers of filler - fills up to 75mm deep in one application. Easy to use - lightweight paste is incredibly easy to apply. No sanding required - finishes to a smooth surface. No sagging - the lightweight properties of Sika® Filler One Strike prevent sagging even on ceilings. Non-shrink - will not shrink back whilst drying. Quick drying - ready to paint/paper in just 30 minutes. Overpaintable with most solvent based and emulsion paints. Overstainable Internal/external use. Dries brilliant white Product Data Appearance / Colour Lightweight brilliant white paste Packaging 300 ml cartridge Storage Storage Conditions / Shelf-Life 24 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost. Technical Data Chemical Base Filled water based polymer dispersion. Density ~ 0.49-053 kg/l Solid Content ~ 61% (w/w) pH 8.0 – 9.0 Grading Dmax : 0.12 mm Layer Thickness Maximum Width: 50 mm Maximum Fill: 75 mm System Information Application Details Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 cartridge of Sika® Filler One Strike yields 0.3 m 2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +30°C max. Ambient Temperature +5°C min. / +30°C max. Application Instructions Mixing Sika® Filler One Strike is supplied ready to use - no mixing is required. Application Method / Tools Apply direct from pail with spatula/spreader. Smooth over surface and allow drying. Sanding is not normally required although the product may be sanded if required. Sika® Filler One Strike can be painted over after approx. 30 minutes using water based paints. Leave to dry for 12 hours when using solvent based paints. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: Note: ~ 30 minutes at 20°C The drying time correspond to thin layer thickness. If deep holes or cracks are filled, longer time is required in order for the product to harden in its full thickness. Notes on Application / Limitations • Do not use to fill plastic or metals. • Do not apply when rain is imminent (external use). • Do not apply in temperatures (ambient and surface) below 5°C. • If using externally overpainting is essential
$13.00
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$88.91
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$20.57
You have seen 48 out of 246 products
Stays where you put it, perfect for vertical and overhead joints, fillets and gap filling. Expect bead stability during cure and cleaner lines. Choose flexibility or rigidity based on movement needs. Use filters to refine by chemistry, viscosity and cure speed. Always check the product page and TDS/SDS.
