Door & Window Seals

The Premier Blue Garage Door Weather Seal is a 5.2m replacement bottom seal made to retrofit most Steel Line garage doors. It gives a worn or missing door seal a simple, Australian-made replacement and helps keep leaves, dust and debris out of the garage.About the productThis seal is made from UV-protected PVC, so it is built to cope with the sun exposure a garage door bottom edge gets. It is supplied as a single 5.2m length, which suits wide doors and can be trimmed to match your opening. It is made in Australia by Premier Blue.Where to use itIndoors: along the bottom edge of the door, where it sits against the garage floor when the door is closed.Outdoors: the seal is exposed to the weather on the underside of the door, and the UV-protected PVC is made for this.How to use it Confirm your door is a Steel Line model before ordering, as this version is made for those doors. Remove the old seal and clean out the retainer channel so the new seal can seat properly. Fit the new seal along the full width of the door, then trim any excess length. Close the door and check the seal sits evenly along the floor with no gaps. Important notesThis listing is for the Steel Line version. Premier Blue also makes weather seals for other door brands, so check that you are buying the right one. Measure your door width before cutting. Floor surfaces that are very uneven may still leave small gaps. This is a weather seal for the bottom of the door. It is not a floor threshold seal.Specifications Brand Premier Blue Product Garage Door Weather Seal Length 5.2 m Profile size Approx. 60 mm wide x 7 mm high Material UV-protected PVC Fits Most Steel Line garage doors Origin Made in Australia Use Replacement garage door bottom seal Care and storageKeep the seal and door channel free of grit and dirt, and wipe it down with mild soapy water when needed. Store unused lengths flat or loosely coiled, out of direct sun, so the seal does not kink or distort before fitting.

Read more less

The Raven RP48 White Self Adhesive Weather Strip is a soft EPDM rubber compression seal for the gap between a door or window frame and its stop, supplied as a 5 metre coil in white. It is made for gaps of 3 to 5mm and helps reduce draughts, dust, noise and insects around the home.About the productThe strip is made from soft EPDM rubber with a self-adhesive backing, so it peels and sticks without tools or fixings. It is designed to sit in the corner between the stop and the frame, where it compresses as the door or window closes to form a snug seal. It is sold as a 5m pack (2 x 2.5m lengths), which is generally enough for an average door frame.Where to use itIndoors: around internal door frames and window frames to cut draughts, rattles and sound transfer.Outdoors: around external doors and windows to help keep out heat, cold, rain, insects and bushfire embers.It suits timber, aluminium and PVC door and window frames where there is a consistent 3 to 5mm gap.How to use it Check that your gap sits within the 3 to 5mm range. Clean the frame so it is dry, smooth and free of dust and grease. Painted surfaces should be fully cured. Cut the strip to length with scissors or a box cutter. Peel back the backing and press the strip firmly into the corner between the stop and the frame. Close the door or window to check the seal compresses evenly without being forced. Important notesSelf-adhesive seals will not stick well to oily or oil-rubbed finishes, so make sure the surface is properly prepared. The strip is designed to be applied as it comes and is not intended to be stretched. Measure your gap first, as the seal is made for 3 to 5mm gaps only.Specifications Brand Raven Product RP48 Self Adhesive Door and Window Weather Strip Model number R48W Pack 5m coil pack (2 x 2.5m) Colour White Material Soft EPDM rubber Gap size 3 to 5mm Fixing Self-adhesive Weather resistant Yes Use Doors and windows, interior and exterior Care and storageKeep the strip in its pack in a cool, dry place until you are ready to use it. Wipe the installed seal with a damp cloth to remove dust and dirt. Replace it if it becomes flattened, torn or lifts away from the frame.

Read more less

Cyclone Tufflite Ribbed Spline is a hollow core PVC spline for fitting flyscreen mesh into aluminium screen frames, supplied here as a 5mm x 30m roll for larger projects or repeat repairs. The ribbed surface is designed to grip more firmly than a plain spline, which makes it a sensible pick for screens that cop knocks and pressure, such as doors and patio enclosures.About the productTufflite is a professional quality spline made in Australia from soft, UV resistant PVC. The hollow core helps it hold its shape once pressed into the frame groove, while the ribbed surface bites into the channel to keep the mesh tensioned and secure.Where to use itIndoors: flyscreen doors and window screens fitted into aluminium extrusion frames.Outdoors: patio enclosures, screen doors and other exposed screens where a tighter hold is helpful.Features 5mm wide ribbed spline in a 30m roll Hollow core ribbed profile that holds its shape Ribbed surface for a tighter grip and a stronger screen system Soft, UV resistant PVC A better choice for doors and patios than a plain spline Made in Australia How to use itLay the mesh over the frame and press the spline into the groove around the perimeter, working steadily so the mesh stays even and taut. A spline roller makes this job much easier, and Cyclone offers a Tufflite roller for 4 to 6mm spline in synthetic screens. Trim off the excess mesh neatly once the spline is fully seated. Check that the spline width suits your frame groove before you start.Important notesThis spline is intended for installing flyscreen into aluminium extrusion frames. Choose the spline size to suit the groove in your frame, and keep any offcuts for patching or future repairs.Specifications Brand Cyclone Product Tufflite Ribbed Spline Size 5mm x 30m roll Material Soft UV resistant PVC Profile Hollow core, ribbed surface Model number 30121692 Use Flyscreen installation into aluminium extrusion Origin Made in Australia Care and storageStore the roll in a cool, dry place out of prolonged direct sun until needed. Keep the spline clean and free of dust before fitting, and keep small offcuts away from young children and pets.

Read more less

The Moroday MDS4 Brush Door Seal is a white, surface-mounted sweep seal that closes off the gap under a swinging or sliding door, supplied as a single 915mm length. A dense nylon brush faces the gap, so it copes well with rough or uneven floors where a rigid or rubber seal would leave openings.About the productThe seal pairs a PVC extrusion with a nylon brush. The brush is designed to bridge gaps of roughly 10 to 20mm under a door. The strip is self adhesive, and it can also be fixed with screws if you want a more positive hold. It sits on the face of the door, so the door does not need to come off its hinges or track.Where to use itIndoors: the bottom edge of internal swinging doors, or the edge of sliding doors, to cut draughts, dust and insects.Outdoors: external doors and sliding doors where a brush seal is wanted over a gap. It is rated for both interior and exterior use.The brush is especially useful over rough textured floors such as slate or uneven tiles, where the bristles follow the surface better than a flat blade.How to use it Measure the width of your door and trim the strip to length if needed. The full length is 915mm. Clean and dry the mounting face of the door so the adhesive backing can grip. Peel back the backing, position the seal so the brush meets the floor, and press it firmly along its length. For extra security, or on a surface where the adhesive is not enough, the strip can be screwed on instead. Check that the door still opens and closes freely over your floor surface. Important notesThe seal is intended for gaps of about 10 to 20mm, so measure your gap before buying. Very wide or very narrow gaps may need a different style of seal. Adhesion depends on a clean, dry, sound surface. Test the fit before fully peeling the backing, as repositioning is limited once stuck down.Specifications Brand Moroday Product MDS4 Brush Door Seal Model number MDS4 1-67304 Pack 1 x 915mm length Colour White Material PVC extrusion with nylon brush Product size 915 x 42 x 9mm (L x H x W) Sealing gap 10 to 20mm Fixing Self adhesive, or screw on Use Interior and exterior Care and storageKeep the brush free of grit and debris by wiping or brushing it down occasionally. Store unused seals flat in a cool, dry place so the strip and adhesive backing do not warp. Keep out of reach of small children.

Read more less

The Adoored Fabric Draught Stopper is a simple, good-looking way to close the gap under an interior door, supplied as a single stopper in your choice of Charcoal, Grey or Brown. It sits along the base of the door to limit outside air coming in and conditioned air escaping, which can help your heating and cooling work less hard.About the productThis is a fabric-covered door draught stopper made for interior doors. The fabric is hard-wearing yet neat in appearance, so it blends in with most home and office decor. It is designed to move with the door when the door is pushed, so you are not tripping over it or dragging it out of position every time you pass through.Where to use itIndoors: along the bottom of interior doors in bedrooms, living areas, hallways, home offices and similar spaces where you want to cut down on draughts and help hold in warm or cool air.Outdoors: not intended for exterior use. It is made for interior doors only.How to use it Position the stopper along the base of the door so it covers the gap between the door and the floor. Check that the door still opens and closes freely over your flooring before relying on it. Choose the colour that best suits your door and floor: Charcoal, Grey or Brown. Sold individually, so order one for each door you want to seal. Important notesColour is selected at the time of ordering and each unit is sold on its own, not as a multipack. It is designed for interior doors, so it is not a substitute for a weather seal on exposed external doors. Very large or uneven gaps may not be fully covered, so measure your door width and the gap before buying.Specifications Brand Adoored Product Fabric Draught Stopper Model number T1011 Pack Single stopper Length Approx. 830 mm Material Fabric Colours Charcoal, Grey, Brown Door type Interior Use Interior only Care and storageKeep the stopper clean and dry, and brush or vacuum off dust and pet hair as needed. Spot clean marks gently and avoid soaking the fabric. Store flat and away from damp areas when not in use.

Read more less

The Premier Blue Garage Door Weather Seal is a 5.2 metre replacement bottom seal made to retrofit most Gliderol garage doors, helping to keep leaves, dust and debris out of your garage. It is made in Australia from UV protected PVC and is designed to slide straight into the existing bottom rail of the door, so a worn or damaged seal can be replaced without specialist tools.About the productThis is a flexible PVC seal strip that fits into the channel along the bottom of the door and sits against the floor when the door is closed. The UV protected PVC is intended to cope with outdoor exposure. The 5.2 m length is cut to suit your door, which is handy for wide doors and leaves spare material for trimming.Where to use itIndoors: sits in the bottom rail of the garage door on the inside of the opening, forming a barrier at floor level.Outdoors: faces the weather at the base of the door, reducing the amount of leaves, dust and debris that blow or wash into the garage.How to use it Open the door to a comfortable working height and gain access to one end of the bottom rail. You may need to loosen one door guide to do this. Slide the old seal out of the bottom rail. Lubricate the rail with soapy water, then slide the new seal into the rail along its full length. Re-tighten the door guide, then trim any excess so the seal finishes neatly at each end. Important notesThis listing is the Gliderol version, so compare the profile of your existing seal with the product before you buy. Other Premier Blue seals are made for other door brands. Leaving a little extra length at each end when trimming is sensible, because PVC can move slightly with temperature. Some installs may take two people, especially on wide doors. The seal is for the bottom of the door only. A separate floor seal and adaptor rail are sold individually if you need them.Specifications Brand Premier Blue Product Garage Door Weather Seal (Gliderol fit) Length 5.2 m Profile Approx. 50 mm wide, 6 mm thick Material UV protected PVC Compatibility Most Gliderol garage doors Origin Made in Australia Use Bottom-of-door seal, replacement Care and storageKeep the seal clean by wiping it down with mild soapy water now and then, and clear any trapped grit from the rail when you replace it. Store the coil flat or loosely coiled in a cool, dry place out of direct sun until you are ready to install it. Inspect the seal periodically and replace it when it hardens, cracks or no longer sits snugly against the floor.

Read more less

The Premier Blue Garage Door Weather Seal is a replacement bottom seal made to retrofit most B&D garage doors, supplied as a single 5.2m length. It gives a worn or damaged door a fresh seal along the base and helps keep leaves, dust and general debris out of the garage. It is made in Australia from UV-protected PVC.About the productThis is a flexible PVC seal profile that fits into the bottom channel of a compatible garage door. The PVC is UV protected, so it is built to cope with sun exposure along the base of the door. The 5.2m length gives enough material to fit wide doors, and it can be trimmed to suit.Where to use itIndoors: not applicable, this seal is designed for the bottom edge of a garage door.Outdoors: fits the base of a garage door that faces the weather, where it helps block leaves, dust and debris from blowing in underneath.How to use it Remove the old seal from the bottom channel of the door and clear out any dirt or debris from the channel. Feed the new seal into the channel along the full width of the door. Trim the excess length with a sharp knife so the seal sits neatly at the ends. Check the fit matches your door before you cut. This listing is for the version intended for most B&D doors. Other door brands may need a different profile. Important notesThis is a bottom seal that fits into the door's own channel. It is not a floor-mounted threshold seal, and it does not include an adaptor rail. If your door does not have a suitable bottom channel, check compatibility before buying. If you are not sure, compare the old seal profile with the dimensions below.Specifications Brand Premier Blue Product Garage Door Weather Seal (bottom seal) Pack 1 x 5.2m length Material UV-protected PVC Profile size (approx.) 50mm wide x 5mm high Length 5.2m Compatibility Retrofits most B&D doors Use Garage door bottom seal Origin Made in Australia Care and storageWear gloves when removing the old seal and handle any sharp track edges with care. When fitting, use a sharp knife with a controlled cutting action and cut away from your body. Keep any unused length out of direct sun and away from heat until installation. Wipe the seal with a damp cloth from time to time to keep dirt from building up along the base.

Read more less

The Raven RP48 is a self-adhesive grey weather strip for door and window frames, supplied as a 5m pack (2 x 2.5m lengths) that is enough for an average door frame. It is made from soft EPDM rubber and sits in the corner between the stop and the frame, where it compresses to close off the gap.About the productThe strip is a soft, closed-cell EPDM rubber seal with a self-adhesive backing. It suits gaps of 3mm to 5mm, and you set the final gap yourself when you fit it. The profile is about 9mm wide and 6mm high. Raven describes it as a DIY product that helps cut down draughts and rattles and can also be used as a cushioning strip.Where to use itIndoors: around the perimeter of internal doors and windows, to reduce draughts, rattles and noise.Outdoors: on external door and window frames, including single or double doors that open inwards or outwards, security screen doors and bi-fold doors. It also suits awning, casement and hopper windows.How to use it Clean the frame so it is smooth, and make sure any paint is fully cured. Use a pin to carefully separate the backing from the adhesive. Separate the twin rubber strip into a single strip. Fit the seal on the latch side and the hinge side of the frame, in the corner between the stop and the frame. Cut to length with scissors or a box cutter. Important notesSelf-adhesive seals will not stick to oil-rub finishes. The surface must be clean, smooth and well cured if painted. Check that the gap falls between 3mm and 5mm before fitting. This pack is for the grey colour only.Specifications Brand Raven Product RP48 Self Adhesive Door and Window Weather Strip Model number RP48 (R48G) Pack 5m coil pack (2 x 2.5m) Colour Grey Material Soft EPDM rubber Profile size About 9mm wide x 6mm high Gap size 3mm to 5mm Fixing Self-adhesive Tools required Scissors or box cutter Care and storageKeep the strip in its pack in a cool, dry place until you are ready to fit it. Avoid touching the adhesive face, as dust and oils reduce grip. Wipe the fitted seal with a damp cloth when needed.

Read more less

The Raven RP59 is a self-adhesive weather strip for door and window frames, supplied here in white as a 5m length (2 x 2.5m) that suits an average door frame. It is a soft EPDM rubber seal that sits in the corner between the stop and the frame, where it squeezes into the gap to form a compression seal.About the productThe strip is made from extra soft EPDM sponge rubber with a self-adhesive backing, so you can fit it with simple tools and no fixings. It is designed for small gaps of 2mm to 4mm, and the compression seal helps cut down on draughts, dust, noise and insects around the frame.Where to use itIndoors: around the stops of internal door frames and window frames to tighten up gaps and reduce rattles and draughts.Outdoors: on the frames of external doors and windows, set into the corner between stop and frame.How to use it Check that the gap between the stop and the frame is between 2mm and 4mm. Make sure the contact surface is clean and smooth. Painted surfaces should be fully cured. Cut the strip to length with scissors or a box cutter. The 5m pack comes as two 2.5m lengths, which is enough for an average door frame. Peel back the backing, press the strip firmly into the corner between the stop and the frame, and work along the full length. Important notesThe adhesive will not stick to oil-rubbed finishes. It is a non-stretch strip, so lay it in place rather than pulling it tight. Suited to Raven's listed door types (single and double, inward and outward opening, security screen and bi-fold) and window types (awning, casement and hopper).Specifications Brand Raven Product RP59 Self Adhesive Window and Door Weather Strip Model number R59W Pack 5m (2 x 2.5m) Strip profile 9mm wide x 4mm high Colour White Material Soft EPDM sponge rubber Suits gaps 2mm to 4mm Fixing Self-adhesive Use Interior and exterior door and window frames Care and storageKeep the strip in its pack until you are ready to fit it, and store it somewhere cool and dry out of direct sunlight. Apply to clean, dry surfaces for the best grip. If you ever need to replace it, peel the old strip off and clean away any residue before fitting a new one.

Read more less

The Raven RP14B is an extra thick, self-adhesive foam weather strip for the wider gaps around doors and windows, supplied as a 2.5 metre white coil. It is a simple DIY fix for draughts and rattles, and it also works well as a cushioning strip.About the productA soft, open cell urethane foam strip with a self-adhesive backing, so there is no glue, nails or special tools to deal with. At 12mm wide and 12mm thick, it is the thick option in the Raven DIY range and suits user-determined gaps of 8mm to 11mm. It is non-stretch, which helps it keep its shape as you press it into place. The white finish blends in with most painted frames.Where to use itIndoors: around the perimeter of door frames and window frames to cut down on draughts, dust and noise, and to stop loose doors and sashes from rattling.Outdoors: on exterior door and window frames where you want to close up a gap. Fit it to the frame, not to surfaces that stay wet.How to use it Measure the gap first. The strip is intended for gaps of about 8mm to 11mm, and the closed door or window should compress it lightly. Clean the frame so the surface is smooth, dry and free of dust or grease. Painted surfaces need to be fully cured. Cut the strip to length with scissors or a box cutter. Peel back the backing a little at a time, then press the strip firmly along the frame. Close the door or window to check the fit and the seal. Important notesSelf-adhesive seals will not stick well to oiled or alkyd finishes, or to easy-clean wash and wear paints, so choose a clean, smooth, fully cured surface. This strip is made for gaps of 8mm to 11mm. For narrower gaps, a thinner Raven strip will be a better match. Allow for the compression of the foam when you check how a door or window closes.Specifications Brand Raven Product RP14B Self Adhesive Thick Weather Strip Length 2500mm (2.5m coil) Profile 12mm high x 12mm wide Colour White Material Open cell urethane foam Fixing Self-adhesive Suitable gap 8mm to 11mm (user determined) Location Perimeter of doors and windows Tools needed Scissors or box cutter Care and storageKeep the strip in its pack until you are ready to fit it, in a cool, dry place away from direct sun. Wipe the installed strip gently with a damp cloth if it gets dusty. Replace it once it has flattened or lost its grip, and peel it off slowly to reduce marking on the frame.

Read more less

The Raven RP14A is an extra wide, self-adhesive foam weather strip in white, supplied as a 5 metre coil for sealing the gaps around doors and windows. It is a simple DIY fix for draughts, rattles and the dust and insects that find their way in through loose-fitting frames.About the productThe strip is made from open cell urethane foam, which is soft and compressible so it conforms to uneven frames and closes up gaps. It has a pre-applied adhesive backing, so there is no glue to mix or apply. The wider profile than the standard RP14 suits larger gaps of about 3mm to 5mm, with the exact fit left to the user to judge. A 5m length is generally enough for an average door frame.Where to use itIndoors: around the perimeter of internal door and window frames where you want to cut draughts, rattles and noise.Outdoors: around the frames of external doors and windows to help keep out heat, cold, dust and insects.How to use it Clean the contact surface so it is smooth, dry and free of dust and grease. Painted surfaces should be well cured. Measure the frame and cut the strip to length with scissors or a box cutter. Peel back the backing a little at a time and press the strip firmly into place along the frame, so the foam sits where the door or window closes against it. Close the door or window to check the seal. It should compress lightly without stopping the door or window from latching or closing. Important notesThe adhesive will not grip oiled or alkyd finishes, or easy-clean wash and wear paint surfaces, so choose a clean, plain surface. The strip suits gaps of roughly 3mm to 5mm, so check your gap before buying. Not intended for use as a bottom door seal where it would be dragged along the floor.Specifications Brand Raven Product RP14A Self Adhesive Extra Wide Weather Strip Model number R14A Length 5m coil Width 19mm Thickness 6mm Colour White Material Open cell urethane foam Fixing Self-adhesive backing Suitable gap 3mm to 5mm (user determined) Location Perimeter of doors and windows Tools needed Scissors or box cutter Care and storageKeep the coil in its packaging in a cool, dry place until you are ready to install it, away from direct sun and heat. Wipe the installed strip gently with a dry or slightly damp cloth if needed. If the foam becomes worn or flattened over time, peel it off and fit a fresh length.

Read more less

The Raven RP14 is a self-adhesive foam weather strip in grey, supplied as a 5m length for sealing the gaps around doors and windows. It helps cut down draughts, dust and insects, and the peel-and-stick backing makes it an easy weekend job for most households.About the productA compressible, open-cell urethane foam strip with a self-adhesive backing, designed to sit in the gap between a door or window and its frame. The foam is soft enough to squash into the gap and keep contact with the surface, which helps block air movement, dust and insects. It is a non-stretch strip that you simply cut to length. One 5m length is generally enough to go around an average door frame.Where to use itDoors: around the perimeter of the door frame to close the gap between the door and the frame.Windows: around the frame of awning, casement and hopper windows where the sash meets the frame.Suited to timber and aluminium door and window frames, provided the contact surface is clean, smooth and dry.How to use it Measure the gap first. This strip is intended for gaps of roughly 3mm to 5mm. Clean the contact surface so it is smooth, dry and free of dust and grease. Painted surfaces should be fully cured. Cut the strip to length with scissors or a box cutter. Peel back the backing paper a little at a time and press the strip firmly into place along the frame. Close the door or window gently and check that it still latches comfortably. Important notesThe adhesive will not grip well on freshly painted surfaces that have not cured, or on oil-rubbed finishes. Choose the strip to suit the gap: if the gap is outside the 3mm to 5mm range, a different Raven profile may suit better. Leftover strip can be kept for later repairs.Specifications Brand Raven Product RP14 Self Adhesive Weather Strip Model number R14G Length 5m Strip height 6mm Colour Grey Material Foam Fixing Self-adhesive Suitable gap 3mm to 5mm Use Perimeter of doors and windows Care and storageKeep the unused strip in its pack in a cool, dry place away from direct sun until you are ready to use it. Wipe the installed seal gently with a damp cloth when needed, and replace it once the foam is flattened, worn or no longer sticking. Keep out of reach of young children.

Read more less

Syneco Self-Adhesive Door and Window Weather Seal is a soft black EPDM rubber strip that helps cut down draughts, dust and noise around doors and windows. It comes as 5 metres in total, supplied as two 2.5 metre lengths, so it suits a few average-sized openings around the home.About the productThe strip is made from soft, flexible EPDM rubber and has a self-adhesive backing, so there is no separate glue to buy or mix. It is designed to sit in the corner between the door or window stop and the frame, where it compresses to form a seal. The profile is 9mm wide and 6mm high, and it is suited to gaps of about 3 to 6mm.Where to use itIndoors: around internal door and window frames where you want to reduce draughts, dust and noise.Outdoors: this product is described as being for interior use, so it is not recommended for exposed outdoor locations.How to use it Measure the gap you want to seal first. The strip suits gaps of roughly 3 to 6mm. Clean the frame surface so it is free of dust, grease and loose paint, and let it dry fully. Cut the strip to length with sharp scissors or a utility knife. Peel back the protective liner a little at a time and press the strip firmly into the corner between the stop and the frame. Close the door or window gently to check that the seal compresses evenly without making it hard to close. Important notesCheck that your gap sits within the 3 to 6mm range before you buy, as a seal that is too thick can make a door or window hard to close. Self-adhesive strips bond best to clean, dry, sound surfaces. Test a short length on your frame first if it has a textured or freshly painted finish.Specifications Brand Syneco Product Self-Adhesive Door and Window Weather Seal Model number SY-130605 Pack 2 x 2.5m lengths (5m total) Profile 9mm wide x 6mm high Colour Black Material EPDM rubber Suitable gap 3 to 6mm Fixing Self-adhesive backing Use Interior Care and storageKeep the strip in its packaging in a cool, dry place until you are ready to fit it, and keep the adhesive face covered so it stays clean. Wipe the installed seal with a damp cloth when needed. Avoid harsh solvents, which can affect the rubber and the adhesive.

Read more less