🌍 Worldwide Shipping Available | Fast & Secure Delivery ✈️

Gap Filling

162 products

  • Timbermate Woodfiller putty crack filler Interior 2Kg [Jarrah] Timbermate Woodfiller putty crack filler Interior 2Kg [Jarrah]

    Timbermate Timbermate Woodfiller putty crack filler Interior

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Timbermate Wood filler is an Interior grade 4 in 1 Wood Putty, Grain Filler, Edge Filler and Crack Filler. When thinned slightly with water can also be used as a sanding sealer. Timbermate does not shrink, sink, crack or fall out and has an indefinite shelf life. It is non-flammable, non-toxic and can be used to the last gram. The secret ingredient of Timbermate is tap water, therefore, containing no Acrylic, Latex or Solvents. Timbermate comes in 13 premixed colours plus Natural Tint Base. Timbermate takes all types of known stains, varnishes and coatings. The Timbermate formula is over 85 years old and is the only genuine water-based formula in the world proving that the formulation has stood the test of time. Features & Benefits of Timbermate No Waste, Usable to the last drop. If tub dries out just add water to soften. Won't Shrink, Sink, Crack or Fall Out. Suitable for use in all Timbers including Particle Board M.D.F. (Custom Wood) *Plaster Board, Flooring, Panelling etc. Can be used as Wood Putty, Sanding Sealer, Prime Coat, Grainfiller, Crackfiller, Undercoat & Edge Filler all in one. Available in 13 Timber Tones plus Natural. Use White for top coats only. Can be tinted in wet state or overstained when dry. Use any type of Colorant i.e. Water Based Spirit based ochers etc. Easy sanding, will not clog paper when DRY Sanded dust can be mixed with water for re-use. Fast drying approx. 20-30 min, but can be heat dried with a heat gun or lamp for faster drying. Temperature can affect drying time. Clean hands or tools with water. Non-Flammable, Non-Toxic, Non-Yellowing. Solvent, Latex and Acrylic Free. Heat Proof and Freezeproof. Provides a strong foundation for all top coats inc. Single & two pack products polyurethane's, oils, acrylics, french polish wax etc. Takes nails, screws, planing, sawing, drilling and routing Can be used on Metal, Plastic, Fibreglass and in Foundries. 100% Australian Made and Owned. Available in pack sizes of 250g, 500g, 2Kg, 8Kg, 20Kg and 200Kg. Interior Grade. Edgefiller Apply TIMBERMATE with a spatula or knife using hand pressure to force into the Edge or End of the grain. For spray gun use stir 10%-15% water into TIMBERMATE fit a 2mm mozzle and set pressure to 60psi. Boards can be stacked for easy spraying. Allow to dry and sand with a fine grit paper and apply topcoat. Woodfiller/Wood Putty Fills cracks, knots, pin and screw holes, splits, blemishes, etc. Fill deep holes in layers allowing time for each layer to dry. Will not blind natural wood grain. Drying time is about 30 minutes. TIMBERMATE dries hard and smooth without shrinking or sinking and can be belt or drum sanded as it is not affected by heat, the hotter it gets the harder and faster it sets and that means less "Down Time."  You can speed dry TIMBERMATE by adjusting the surrounding air temperature. This can be done by using either hot air, heat lamps, or kiln ovens.TIMBERMATE can be mixed with any stains before or after the filler is dry. To match medium and darker shades mix with Natural, Pine or other light shades. Use white TIMBERMATE only for white top coats. Grainfiller Mix 10% to 15% water into TIMBERMATE to make a perfect Grainfiller, Sanding Sealer and Prime Coat all in one application. First sand surface and with fine grit sandpaper, then apply Grainfiller to surface with a spray gun, paint roller, hessian or a cloth rolled into a ball, rub across the grain in a circular motion finishing with the grain. Sand, once filler is dry, to perfection with either sandpaper or power sander, using a fine grit paper. Grain filer can be used in a Roller or Curtain Coater or Spray Gun using a 2mm nozzle and 60psi pressure. Can be further thinned down with water if required. MDF Due to the finishing system used to manufacture MDF, it is essential to seal the job with a water-based non-acrylic product before applying top coats. Therefore TIMBERMATE meets your needs. Flooring Preparing old floors: Scrape all dust and waste between boards and surface as well as from knot holes and nail heads, vacuum well and carry out first sanding to prepare for filling and coating. Ensure that floor is stabilised, dry and free of movement. Application new floors and prepared old floors: Fill cracks, knot and nail holes and all blemished with a putty knife. Fill deeper holes in layers of about 6mm allowing each fill to dry. Apply TIMBERMATE to the entire floor, as a sealant, using a squeegee, trowel or paint roller. Allow to dry and sand off with a fine paper - 120 to 150 grit is recommended for best results. The floor can now be stained or varnished. Frequently Asked Questions Question: Is TIMBERMATE toxic, flammable or harmful? Answer: It is advisable to carry out safe work practices, as you would when working with dust. (Use an approved dust mask and safety goggles). TIMBERMATE contains no harmful ingredients and is non-flammable. Question: Can TIMBERMATE be used externally? Answer: No, as TIMBERMATE® is resoluble in water it is not advisable to use it outdoors. TIMBERMATE IS RECOMMENDED FOR INTERIOR USE. For external use, we recommend Earls MulTFill, Powder Putty or Porion Flexible Filler. Question: Can TIMBERMATE be used with stains and other finishes? Answer: Yes, TIMBERMATE® will take all types of known stains, coatings and colourants which can be Water based, Oil based, Solvent or Spirit based and even Acid Catalysed Lacquers. Question: Can TIMBERMATE be grainfilled? Answer: Yes, TIMBERMATE is a non-solvent based filler and is ideal for grainfilling. Mix 10-15% hot water to thin the Timbermate, then rub over the grain or spread thinly (see below for more detailed instructions). TIMBERMATE will: *Not raise the grain *Not damage the grain TIMBERMATE is: *Easy to sand when dry *Easy to stain when dry *Heat proof so you can speed the drying time by heating with a hair dryer, heat gun, lights etc. Question: How is the grainfiller applied? Answer: Take some TIMBERMATE out of the tub and place it in a separate container. Add approximately 10-15% water, (1gm=1ml) and mix into a slurry like paste (like toothpaste). Use a LINT FREE CLOTH AND RUB ACROSS THE GRAIN. When grainfiller goes "whitish" and sands off easily like talc powder, it is dry. TIMBERMATE will not blind the sandpaper (ie. clog up). If sandpaper gets clogged the grainfiller is not dry. Sand off in the same direction as the grain. Stain or coat when dry. Question: When is the stain applied? Answer: You can stain before or after applying TIMBERMATE (see "How do I match colours"). Question: How are the colours matched? Answer: Colour matching is easy. You can do it either of the following ways: Add your colourant to the putty and match the exact colour whilst wet. TIMBERMATE will dry lighter, but coat back to its original wet colour once coated with clear finishes. The final result is what you see (wet) is what you get. You can stain TIMBERMATE once it is dry. To test if dry, just rub sandpaper over putty. If putty clogs the sandpaper the filler is still wet. Wait for TIMBERMATE to dry and then stain. Question: How long does TIMBERMATE take to dry? Answer: Depending on the weather and depth of fill, TIMBERMATE will dry as follows: In hot weather, TIMBERMATE dries quicker. In cold weather, the depth of fill will determine the drying time. You can speed up the drying time by using a heat gun, hair dryer or light. Question: What depth or width can be filled? Answer: Do not fill holes deeper than 6-8mm at a time. TIMBERMATE dries quicker when filled in layers. Allow TIMBERMATE to dry between layers. Question: Why is the tub hard some days and feels dry and soft on other days? Answer: TIMBERMATE is waterbased. It contains no harmful solvents or acrylics and is, therefore, temperature sensitive. The warmer the weather or environment the softer the putty. On hot days it will start to dry in the tub if not properly sealed. Add a few drops of water to re moisten. Question: How is TIMBERMATE softened? Answer: Add a few drops of warm water to the top of the tub. It will soften quite quickly. If tub is frozen, thaw out by standing tub in a tub of hot water or place in a microwave for 20 seconds. TIMBERMATE is freeze thaw stable. Question: Can TIMBERMATE be used for any other purpose other than wood repair? Answer: TIMBERMATE does not shrink, sink, crack or fallout and can, therefore, be used on Plasterboard, Masonry, Fibreglass, Plastic and any other surface. Bearing in mind that steel must be coated with a primer to avoid rusting. Question: Can TIMBERMATE go off or does it have a shelf life? Answer: TIMBERMATE has an unlimited shelf life and will last indefinitely. If contents become dry merely add a few drops of water to reconstitute. DO NOT add more water than is necessary or leave excess water in the tub for a long period of time. The trapped excess water in the tub will cause the putty to become contaminated and will start to degenerate. Question: Why are so many colours available? Answer: We manufacture 13 colours to match almost all shades and types of timber. If you are using a clear coat you must match your putty colour. If staining, use Natural (tinting base). Question: What is Tint Base (Natural) putty and why? Answer: Tint Base (Natural putty) is putty in its natural state uncoloured. You may add the lightest shade of tint to change its colour. Question: Can TIMBERMATE be used on floors? Answer: TIMBERMATE is ideal for filling cracks, gaps, and nail holes in floors. TIMBERMATE will enhance the grain on the floor. As it does not shrink, sink, crack or fall out it is highly recommended for all floors. Question: Can TIMBERMATE be used with French Polish and Waxes? Answer: You can use all types of Waxes, Shellac and Oils on TIMBERMATE. Question: How is an incorrect match or badly filled hole fixed? Answer: Errors can be fixed with ease. If TIMBERMATE is not coated then wash out. If already coated, then break the top coat and then wash out. Refill or rematch if necessary. Question: Is TIMBERMATE Australian owned and manufactured? Answer: Yes. TIMBERMATE is 100% Australian owned and manufactured. An all Australian dedicated workforce does all manufacturing in our Melbourne factory.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $0.00 - $89.00

  • Araldite 5 Minute Epoxy Adhesive Holds 75Kg For Everyday Use Dries Clear 35ml Araldite 5 Minute Epoxy Adhesive Holds 75Kg For Everyday Use Dries Clear 35ml

    Selleys Araldite 5 Minute Epoxy Adhesive Holds 75Kg For Everyday Use Dries Clear 35ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $18.00

  • Earl's MulTfill Multi-Purpose Paintable Putty Interior & Exterior Filler

    Timbermate Earl's MulTfill Multi-Purpose Paintable Putty Interior & Exterior Filler

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Earl’s MulTfill is a premium, ready-to-use multi-purpose filler designed for fast, clean, and durable repairs across interior and exterior projects. The heavy-bodied formula spreads smoothly, levels cleanly, and dries hard without shrinking, sinking, cracking, or falling out. With zero VOCs and no acrylics, latex, or solvents, it’s a low-odour choice for homes, workshops, and job sites. Clean-up is simple with water, and once dry MulTfill sands easily to a fine, paint-ready surface. Why you’ll love it Ready from the tub: no mixing, no mess, no wastage — just open, apply, and close. Zero VOCs: stable, low odour and user-friendly. Non-sinking, non-shrinking: fills stay flush and true. Won’t fall out: dries hard for lasting repairs. Paintable finish: accepts most coatings for a seamless result. Sands like a dream: refined finish without clogging when sanded dry. Long shelf life: keep the lid sealed and it’s ready when you are. Where it works Use MulTfill on common building materials including wood (including weathered and damaged sections once sound), masonry, plasterboard, cement sheet, concrete, and primed metal. It’s ideal for nail holes, dents, shallow voids, corner repairs, skim touch-ups, and general surface preparation before painting. Colour options White, Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut. How to use Prep: Ensure the area is clean, dry, and sound. Remove loose material and dust. For best glide, lightly wet your putty knife. Apply: Press firmly to fill the defect and smooth off. For deep voids, apply in layers up to 6 mm per pass, allowing each layer to dry before the next. Sand: Once fully dry, sand with 120 grit or finer to achieve a smooth, level surface. Coat: Prime if required, then paint. For clear finishes, tint the filler with suitable colorants or oxides before application to harmonise with surrounding material. Cleanup & care: Clean tools with water. If product thickens in the tub, add a few drops of clean water and stir until smooth. Always reseal promptly. Pro tips Feather edges wide when blending across boards or wall patches. On exterior jobs, protect from rain during cure and overcoat appropriately for exposure. Tinting before clear coats helps the repair visually disappear on timber substrates. Specifications Brand Earl’s Product Type Multi-purpose paintable putty / filler (water-based) Use Interior and exterior VOC Zero VOC Contains No acrylic, latex, or solvents Substrates Wood, masonry, plasterboard, cement sheet, concrete, primed metal Application Thickness Up to 6 mm per layer; allow to dry between layers Sanding Dry sand; 120 grit or finer Overcoating Accepts most paints; for clear coats, tint filler first for best colour match Clean-up Water Colours White; Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut Pack Sizes 140 g, 600 g, 1 kg, 2 kg, 3 kg (varies by colour) Shelf Life Up to 5 years if sealed and stored correctly Country of Origin Australia Storage Keep container tightly closed when not in use. Store in a cool, dry place out of direct sun. Avoid prolonged freezing. If product thickens, add a few drops of water and mix to restore spreadability. What’s in the tub A smooth-spreading, heavy-bodied filler that levels cleanly, sands easily, and delivers a paint-ready finish across interior and exterior surfaces — with no mixing, no fuss, and no strong odour.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $6.00 - $52.00

  • Selleys No More Gaps Coloured Caulk Sealant 450g [Brilliant White] Selleys No More Gaps Coloured Caulk Sealant 450g

    Selleys Selleys No More Gaps Coloured Caulk Sealant 450g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    No More Gaps Coloured Gaps No More Gaps Coloured Gaps offers a long-lasting, colour-matched finish, suitable for both interior and exterior use. It comes in a wide range of colours, with no need to paint over (although it is paintable if required). It provides superior flexibility to cope with building movement, hiding cracks and gaps longer, with greater than 350% elongation/stretch and up to +/- 20% movement capability. Key Features Long-lasting, colour-matched finish Suitable for Interior & Exterior use Available in a great colour range, with no need to paint over (Paintable if required) Superior flexibility to cope with building movement, hiding cracks and gaps longer Greater than 350% elongation/stretch and up to +/- 20% movement capability Good resistance to weathering Superior adhesion to a broad range of surfaces, resulting in a lasting finish Mould and mildew resistant Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles (not exposed to water) In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Bare or painted surfaces Colorbond Many other building materials How to Use Ensure the surface is clean, dry, and free from dust, grease, flaking/powdery paint, and old or crumbling caulk. Cut the seal and nozzle, fit it to the top of the cartridge, and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking Gun. Hold the caulking gun at a 45° angle and apply, forcing the product into the gap. Smooth with a wet finger or spatula. Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow surface to skin thoroughly prior to painting with water-based paints. If using oil-based paints or for large gaps, allow the sealant to set for about 24 hours and ensure the product is completely cured. Avoid water contact until fully cured – 72 hours or longer in cold weather. Limitations Not recommended for foot traffic areas, gaps between tongue and groove boards, or weatherboard overlaps. Use Selleys No More Gaps Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards, and Selleys No More Gaps Exterior & Weatherboard Gap Filler for weatherboard overlaps. Not suitable for areas in prolonged contact with water (e.g., showers, pools, & spas). Use Selleys Silicone Sealant for significant joint movement or areas of frequent water immersion. Do not apply or store below 5°C. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easier cleanup. When first applying, extrude a small amount onto scrap material to ensure smooth, continuous flow of gap filler. If wiping off excess with a wet finger, wet it with water (not saliva) to avoid bacteria that can promote mould growth. Allow surfaces to skin before painting, approximately 30 minutes. Protect from rain until the surface is firmly skinned. Some water-based undercoats and flat paints may crack when drying. To reduce this, allow the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting. Keep a pack of Selleys Sugar Soap Wipes handy for easy cleanup. Clean Up Water-based, so clean up with water. Uncured product may be removed with water. Cured product can be removed by sanding and scraping. Size 450g Cartridge Colours Black Brilliant White Brown Cedar Charcoal Coffee Cream Ivory Light Grey Technology Water-Based Use Interior & Exterior

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $0.00 - $15.00

  • Sika Sikaflex®-111 Stick & Seal White: 1-Part Adhesive & Sealant 290ml

    Sika Sika Sikaflex 111 Stick & Seal 1-Part Adhesive & Sealant 290ml [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $23.00

  • Selleys No More Gaps Multipurpose Sealant Filler 475g [White]

    Selleys Selleys No More Gaps Multipurpose Sealant Filler 475g [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 300% elongation/stretch and up to +/- 15% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage. Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application). Is formulated for long term resistance to cracking and crumbling. Easy water clean-up Will not stain building materials. Has good resistance to weathering. Low toxic, low odour, low VOC, less harmful to the environment Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles which are not exposed to water In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm  What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Paint Many other building materials

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $5.00

  • Araldite Super Strenght Expoxy Adhesive Holds Heavy Loads Up to 150Kg 24ml

    Selleys Araldite Super Strenght Expoxy Adhesive Holds Heavy Loads Up to 150Kg 24ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6–8 hours, with maximum bond strength after 3 days. Features Stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries clear Very strong and durable bonding High water resistance (suitable for tiles around pools, but not below the water line  for that use Selleys Knead It Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat resistant Clamping recommended for stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but is regained when temperature drops Appearance Translucent Where Can This Product Be Used? Load-bearing repairs Gluing the head back on a hammer Fixing loose table or chair legs Bonding aluminium sheeting Bonding timber on boats Repairing splits and cracks in cricket bats Bonding fibreglass sheets Repairing skis Fixing Dynabolts and metal rods into concrete Suitable Materials Glass Metal Wood Fabric Rigid plastics (except Polyethylene and Polypropylene) Crystal Leather How to Use Ensure all surfaces are clean, dry, and free from grease, rust, or paint. For best results, roughen smooth surfaces after solvent cleaning. Dispense equal volumes of Part A and Part B onto a clean disposable surface (e.g. cardboard or polyethylene) and mix thoroughly. Apply adhesive immediately to both surfaces and press together. Clamp the bond for 6–8 hours while setting. Scrape off excess adhesive and clean utensils immediately. Handy Tips Mix in small quantities for longer working time — large mixes cure faster. Replace caps immediately after use and wipe nozzles with acetone or nail polish remover before sealing. Ensure caps are placed on the correct tubes (they are colour-coded). Remove uncured adhesive with acetone or nail polish remover. Once cured, remove by mechanical scraping or sanding — solvents will not dissolve the product. To reposition a cured bond, heat slowly to at least 150°C (if safe for the material), then scrape off excess and reposition carefully. For cleaning surfaces before use: Porous surfaces use Selleys Liquid Sugar Soap Non-porous surfaces (e.g. glass, metal) — clean with methylated spirits For stubborn residue use Selleys Kwik Strip Smart Ensure the surface is dry before applying. Safety Tips Avoid contact with skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of eye contact, flush with water for 15 minutes and seek medical attention. Non-toxic when set. Refer to the Material Safety Data Sheet (MSDS) for more information. Storage & Reuse Replace caps tightly after use. Store in a cool, dry place.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $24.50

  • Cabot's Wood Tone Putty Hole Filler 250g [Colour: Radiata Pine] Cabot's Wood Tone Putty Hole Filler 90g [Colour: Antique Walnut]

    Cabot's Cabot's Wood Tone Putty Hole Filler

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Cabot's Wood Tone Putty is ideal for filling holes, cracks and blemishes in all interior timber without shrinking. It is easy to apply and sands to a fine, smooth finish. Wood Tone Putty is compatible with water or oil based paints, stains and timber finishes. Areas All interior timber Clean Up Water Product Type Water Based

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $14.71 - $18.92

  • Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]

    Sika Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikaflex-227 is a one-component poly­­urethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $27.48

  • Sikaflex Crystal Clear Multipurpose Sealant & Adhesive 290ml

    Sika Sikaflex Crystal Clear Multipurpose Sealant & Adhesive 290ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces 100% crystal clear / transparent Good workability Very good adhesion on many typical building materials Use: Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including: Plasterboard Wood surfaces Painted enamel Polyester Plastic Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions. CHARACTERISTICS AND ADVANTAGES 100% crystal clear / transparent Good workability Low shrinkage during cure Flexible and elastic Can be used on damp concrete Very good adhesion on many typical building materials COLOUR: Transparent Product Data Appearance / Colours Transparent Packaging 300 g cartridge (290 ml), 12 cartridges per box Storage Conditions / Shelf-Life Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met. Technical Data Chemical Base Silane terminated polymer Density 1.05 kg/l approx. (ISO 1183-1) Tensile Strength 2.0 N/mm2 approx. (ISO 37) Shore A Hardness 30 approx. (after 28 days) (ISO 868) Elongation at Break 400% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Service Temperature −40 °C to +70 °C SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department. Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly. Bonding After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again. Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear. Sealing After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $27.65

  • Sika SikaSeal Gap Filler Acrylic 100 Sandable Paintable [White]

    Sika Sika SikaSeal Gap Filler Acrylic 100 Sandable Paintable [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    DESCRIPTION SikaSeal® Acrylic 100 is a flexible, one component, water based acrylic joint sealant and gap filler where low demand of elongation are required, for interior use. USES SikaSeal® Acrylic 100 is suitable for sealing low movement joints around: ? brick ? Concrete ? Plasterboard ? Windows ? Doors ? Ceramic tiles SikaSeal® Acrylic 100 fills cracks and adheres to: ? Glass ? Wood ? Aluminium ? Brick ? Concrete ? Plasterboard ? Ceramic ? Painted surfaces. CHARACTERISTICS / ADVANTAGES Excellent adhesion to most common construction materials. Water clean-up of uncured sealant. Can be sanded back once fully cured if required to give smooth surface finish. Can be painted over using water based paints. Non-toxic

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $6.50

  • Selleys No More Gaps Multipurpose Sealant Filler 150g [White]

    Selleys Selleys No More Gaps Multipurpose Sealant Filler 150g [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 300% elongation/stretch and up to +/- 15% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage. Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application). Is formulated for long term resistance to cracking and crumbling. Easy water clean-up Will not stain building materials. Has good resistance to weathering. Low toxic, low odour, low VOC, less harmful to the environment Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles which are not exposed to water In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm  What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Paint Many other building materials

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $8.00

  • Selleys No More Gaps Bricks & Mortar x 440g [Terracota]

    Selleys Selleys No More Gaps Bricks & Mortar x 440g [Terracota]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.  Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C.  Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $22.00

  • Selleys Liquid Nails Original Adhesive All Weather High Strength 320g

    Selleys Selleys Liquid Nails Original Adhesive All Weather High Strength 320g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to respond to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces   How to use this product Ensure the surfaces to be bonded are clean, dry and free from dust, grease, oil and loose powdery materials. If porous surfaces are greasy or dirty, we would recommend cleaning the surface with SELLEYS LIQUID SUGAR SOAP, and allow to dry. If the surface is non-porous eg glass or metal, firstly clean the surface with Mineral Turpetine and then again with Methylated Spirits, and allow to dry. If there is old difficult to remove residue such as old flaky paint, we recommend using paint stripper such as SELLEYS KWIK STRIP SMART, and allow to dry. On wet timber pooled water should be wiped off. Highly oily timber types may need to be wiped with solvent prior to application to remove surface oils. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/ Course grain, as the construction adhesive will adhere more readily to a scratched up surface. Cut the seal at the top of the cartridge. Cut the nozzle end to desired opening (approx. 5mm diameter). Fit to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of work which requires a caulking gun. Apply a bead of product along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. Fix the surfaces with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. The product is repositionable for up to 20 minutes after fitting. Allow the adhesive to set (at least 24 hours) before removing any temporary fasteners or clamping. For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-5 minutes before firmly joining. The time it takes to form a strong bond depends on the nature and conditions of the application. In most situations strong bonds can be achieved after 24 hours and will continue to strengthen over a 2-3 day period. The product will fully cure up to 7 days. When the product is still wet it can be removed with mineral turpetine, otherwise if the product is dry it can be removed by sanding or scraping, we recommend using a 50mm ROTA COTA Soft Grip Scraper. Clean any excess from your hands with SELLEYS Hand Kleen Wipes. To eliminate squeaks in tongue and groove flooring, apply a bead of Liquid nails into the groove or each board when installing. Handy tips When applying to one surface, ensure sufficient LIQUID NAILS Original is used so that some adhesive extrudes out when surfaces are brought together then wipe off excess if necessary. If glue is not visible, then insufficient contact may not have been made between the surfaces and a weak joint may result. LIQUID NAILS Original should always be used in conjunction with mechanical fasteners in structural, critical or high stress applications. LIQUID NAILS Original is sometimes called LIQUID NAILS (SOLVENT) to differentiate it from the other Liquid Nails products. LIQUID NAILS Original shrinks slightly on curing. Cured LIQUID NAILS Original residues can be removed by holding a rag soaked in Mineral Turps against the residue, then rubbing the residue once softened. Mineral Turps penetrates in this way at approximately 1 mm per hour. When Liquid Nails Original joints are directly exposed to the weather, it is recommended to seal around the edges with a silicone sealant to prevent water ponding inside the joint and thus weaken the joint. LIQUID NAILS Original is NOT recommended for use on mirrors or polystyrene. Use LIQUID NAILS MIRROR METAL GLASS for mirrors and LIQUID NAILS FAST for polystyrene. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $5.00

  • Poly Gap Filler Sealant Multipurpose [White]

    Poly Poly Gap Filler Sealant Multipurpose [White]

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A flexible multipurpose gap filler, to fill gaps around cornice, wall joints, skirting board, window and door frames where where movement causes ordinary fillers to crack or fall out. For use on: Wood, brick, aluminium, glass, plasterboard, ceramic tiles and painted surfaces (INTERIOR & EXTERIOR) Coverage: 30m/3mm bead. Dry time: Skins in 30 minutes at 25°C. Full cure in 7days. Ready to use: YES Available in: 475g Colour: White NOTE: Not for fine joints between tongue and groove boards or weatherboard overlaps. • Ensure surfaces are clean, dry and free from oil, dust, grease, flaking paint and old sealant. • Using caulking gun, push sealant ahead of nozzle forcing it onto the surface and into the joint. Ensure the sealant is touching both sides of the gap. • Smooth with wet finger or knife and remove excess sealant immediately with a damp cloth. • Allow sealant to skin approx 30 min before painting with water-based paints. • Allow to set for 48 hours if using oil based paint or if joint is large. • Some water-based undercoats and flat paints may crack on drying. Test a small section of sealant. Paint cracking may be reduced by using a vinyl/ acrylic semi glossed paint or oil based undercoats first, or by allowing the sealant to cure thoroughly before painting. • Do not use outside if rain is imminent, not for contantly damp areas. • Painting improves exterior durability. • Use Poly silicone sealants for a watertight seal or where movement is excessive. • Water clean up Q. How do I fill gaps between my wooden window frames and inside wall? A. You're dealing with two different materials here, plaster and wood. To allow for differential movement between them, use Polyfilla Gap Filler, wiping off any excess with a damp cloth. Q. I painted over the areas where I used Polyfilla Gap Filler and now cracks have appeared. Why has this happened? A. If the gap filler was not cured sufficiently before it was painted over, cracks can occur as the gap filler shrinks. To prevent this, allow 48 hours drying time when you are filling large gaps or painting with oil-based paints. Also, some water based undercoats and paints shrink during drying and as Polyfilla Gap Filler is flexible, it won't stop cracks appearing in the shrinking paint on its surface. Test the paint on a small section of gap filler and if this is a problem you can reduce cracking by allowing the filler to cure thoroughly or by first coating it with a vinyl/acrylic semi-gloss or oil-based undercoat. Q. Why does my gap filler keeps cracking? A. It is important to remember that the width of a gap affects how much the product can move. Fine cracks less than 2mm allow the gap filler to move only very tiny amounts before it may crack again. It is best to ensure that you have at least 3mm worth of product so you can maximise the movement capability of your joint.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $5.00

  • PC-7 Epoxy Waterproof Heavy Duty 56g

    PC Products PC-7 Epoxy Waterproof Heavy Duty 56g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    PC-7® is the original tough job epoxy! This paste epoxy was originally formulated more than 60 years ago for the maximum in bonding power. Professionals to the do-it-yourselfers select PC-7® because of its exceptional adhesion to metals, ceramics, masonry and many plastics. PC-7® is designed for permanent repairs. Where other adhesives fail…PC-7® won’t! Choose PC-7® if you want to: seal a crack in a wall, attach a hanger to a ceramic plaque, seal a leak in an oil pan, repair a granite monument, fix a leak in PVC pipe connection, create a multimedia sculpture, and thousands of other repairs. When mixed, part A (gray) and the hardener part B (black) react to form a bond of tremendous strength. The PC-7® formulation is slow curing, but slow can be a good thing especially for large tasks. WORKING TIME: 60 MINUTES CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE) PC-7® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Thicker than peanut butter but not as thick as bubble gum. Here are just a few specific uses (there are hundreds of other uses): Bond metal electrical boxes to concrete wall. Fill cracks in basement walls. Rebuild vintage Bakelite steering wheels. Seal holes in oil and transmission pans or fuel tank. Bond and repair stainless steel. Attach transition strips on concrete floor. Attach firing strips to concrete wall. Bond to and rebuild hard rubber bumper. How to prepare a surface for bonding with PC-7 Epoxy Paste Remove contaminants such as dust, dirt, oil and grime with solvents such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be scuffed using sandpaper to increase adhesion. How to clean-up after PC-7 Epoxy Paste application Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-7® cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. How thick can I apply PC-7®? PC-7® can be applied in any thickness. It does not require drying or exposure to air. It will cure from the inside out. I made a repair with PC-7® but need to build the area up more. Can I apply more epoxy? PC-7® sticks to PC-7® Can I use PC-7® for a vertical repair? PC-7® can be applied vertically and overhead. Because of its high viscosity it will not drip or sag. How long does it take PC-7® to harden? Normally, at 70F, PC-7® will cure in 24 hours but full hardness can take up to 48 hours. Cooler conditions will extend the cure time. Working in a garage or outside in temperatures between 50F and 60F may double the length of time needed for full cure. Applying PC-7® to a cool surface such as an exterior facing wall will slow down the cure. Can I paint over PC-7® and if so how? PC-7® should be primed then painted. Use Zinser Bullseye® 1,2,3 Stain Sealing Primer or Kilz® Premium Stain Sealing Primer or INSL-X® Stix Bonding Primer. Priming/sealing is important to separate and protect the finish coat from the epoxy/amine surface. Can I use PC-7® on a finished surface? Smooth, glossy or shiny surfaces should be roughened or scuffed with sandpaper to provide maximum adhesion. Use 80 or 120 grit sandpaper. A roughened surface has much more surface area than a smooth surface. PC-7® is very thick. Can I smooth it out or thin it out? Use a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol or Lacquer thinner to smooth applied PC-7®. Be-cause PC-7® is very thick and gooey, it is necessary to apply alcohol or acetone to the tool or gloved fingertips in order to lubricate the surface and shape or feather the applied epoxy. Can I use more of one part of PC-7® in order to speed the curing? Adding additional hardener does not make PC-7® cure faster. It is best to mix PC-7® one part of A to one part of B. However, PC-7® is probably the only epoxy that does not require precisely a 1:1 mix ratio. Plus or minus 25% A or B does not affect the performance. Adding additional PC-7® (+50%) part B hardener (black) can improve the adhesion to difficult surfaces such as PVC pipe and fittings. Measure equal volumes of part A epoxy (gray) and part B hardener (black) then measure an additional half portion of hardener (black). This will make the mix ratio (1 : 1.5, A : B). Can I tint PC-7® to match a surrounding color? PC-7® can be tinted with iron oxide or carbon pigments. Powdered pigments are used to color stucco or concrete and can be found at art supply stores. Universal tints that are used to color paint are compatible with PC-7®. Too much tint may affect the performance of PC-7®. I want to do a repair outdoors and the epoxy seems really stiff? PC-7® becomes more viscous in cool temperatures. Set the containers in a warm place prior to mixing. Acetone has been used to reduce the viscosity of PC-7®. The addition of acetone will contribute to shrinking and slow down the cure rate. PC-7® performs best without the addition of solvents. What will PC-7® bond to? It is easier to say what PC-7® will NOT bond to: Wax paper, Teflon, Plexiglass, vinyl and some softer plastics. Test an area if in doubt and always rough up shiny, smooth surfaces with sandpaper.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $17.86

  • Last stock! PC Super Epoxy Industrial Strenght Waterproof 28g

    PC Products PC Super Epoxy Industrial Strenght Waterproof 28g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    PC-SuperEpoxy® is a non-drip translucent paste epoxy suitable for conventional or static mixing. It has unlimited uses in bonding, assembling, filling and sealing most materials. Unlike conventional liquid epoxies, PC-SuperEpoxy® can be applied via a static mix nozzle vertically and overhead. It cures quickly at room temperature to form a resilient, non-conductive bond or seal that resists most chemicals, fresh and saltwater, gasoline and fuel oil. Works great bonding steel to wood, fibreglass, aluminium, concrete, brick, glass, block, ceramics, hard plastics and much more. PC-SuperEpoxy® is the toughest, highest strength epoxy we manufacture. WORK TIME: 15 MINUTES AND TACK-FREE IN 60 MINUTES CURE TIME: 4 HOURS (12 – 24 HOURS FOR FULL CURE) Here is a product that can take on the most challenging of projects with ease. Adhesion strength in excess of 2500 psi (up to 4000 psi). PC-SuperEpoxy® is a gel with a consistency like Vaseline. Here are just a few specific uses (there are hundreds of other uses): Anchoring or securing railings to wood or fibreglass decking. Seal cracks and holes in decking. Attach chocks, cleats, handles and pulls. Anchor or secure iron balusters to step and handrail. Fill cracked wood beam. Fix broken latch in the car glove box. Attach axe head.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $16.12

  • Parfix Maxi Nails 300g: The Ultimate Multi-Surface Construction Adhesive High Strength, Paintable & Perfect for Both Indoor and Outdoor Applications

    Parfix Parfix Maxi Nails 300g: The Ultimate Multi-Surface Construction Adhesive High Strength, Paintable & Perfect for Both Indoor and Outdoor Applications

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Parfix Maxi Nails 300g: The Ultimate Multi-Surface Construction Adhesive Key Features High-strength bond suitable for a variety of applications Paintable for aesthetic versatility Effective both indoors and outdoors Specifications Colour: Beige Model Name: Parfix 300g Maxi Nails Construction Adhesive Material: Polymer Dissolved in Hydrocarbon Solvent Outdoor: Yes Indoor: Yes Why Choose Parfix Maxi Nails 300g? Designed to handle a multitude of construction challenges, Parfix Maxi Nails 300g provides a robust bond that lasts. Whether you're working indoors or taking on external projects, this adhesive is formulated to give you the results you need.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $4.19

  • Loctite Easy Repair Pre-mixed Epoxy no mess 5 minute setting 14ml Loctite Easy Repair Pre-mixed Epoxy no mess 5 minute setting 14ml

    Loctite Loctite Easy Repair Pre-mixed Epoxy no mess 5 minute setting 14ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Loctite Epoxy Instant Mix 5 Minute is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 5 minutes and reaches handling strength in 1 hour. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. Loctite Epoxy Instant Mix 5 Minute does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on: Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fibreglass, concrete and stone Can be combined with fibreglass cloth for a durable patch Great for crafting projects Properties Will not crack when drilled Can be tinted to match surrounding materials Water resistant: can be used outdoors Does not shrink   One-time application Convenient instant mix syringe  Consistently dispenses equal, uniformly mixed amounts of each component Sets in 5 minutes  Quick completion of the project How to Use: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from the centre of the plunger. Turn nozzle end up and pull the plunger back slightly allowing air bubbles to rise to the top. Snap off and discard end of the syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto the surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $9.23

  • Araldite Super Strenght Expoxy Adhesive Maximum Bond 35ml

    Selleys Araldite Super Strenght Expoxy Adhesive Maximum Bond 35ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $29.36

  • Araldite 5 Minute Epoxy Adhesive With Self Mixing Nozzle 14ml

    Selleys Araldite 5 Minute Epoxy Adhesive With Self Mixing Nozzle 14ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance   Appearance: Clear with a slight yellow tinge   Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops   What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather   How to use this product: General Use -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick.   Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $8.00

  • Packshot of Selleys Liquid Nails Construction Adhesive 320g (3 Pack)

    Selleys Selleys Liquid Nails Construction Adhesive 320g (3 Pack)

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to response to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $17.49

  • Packshot of Selleys 635 Clear Multipurpose Sealant 290ml

    Selleys Selleys 635 Clear Multipurpose Sealant 290ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys 635 Multipurpose Elastic Sealant Clear 290 mL Selleys 635 is a premium 100 percent clear elastic joint sealant that delivers strong, flexible and waterproof seals for indoor and outdoor jobs. Powered by hybrid technology, it adheres to most common building materials without primer and resists UV and weather for long lasting performance. Paintable with water based paints after skinning. Why you will love it Crystal clear finish that stays clear Excellent weather and UV resistance for exterior use Primerless adhesion to most surfaces Adheres to damp or wet surfaces Non slumping in joints up to 20 mm Low odour and low VOC, solvent and isocyanate free Paintable with water based paints once skinned Where to use Vertical and horizontal joints on most indoor and outdoor surfaces, including concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles, glass and many other common building materials. Not suitable for Polyethylene, Polypropylene or PTFE, structural glazing, or permanent water immersion. Directions Prep Clean and remove dust, grease and contaminants. Degrease metals. Cut nozzle on a sharp angle slightly wider than the joint. Use a suitable backing rod to control depth where required. Apply Gun the sealant into the joint. Tool within 10 minutes to ensure good contact with joint sides. Paint When skinned, paint with water based paints. For solvent based paints, first apply a water based undercoat and test on a small area. Clean up Clean spills and tools with mineral turps before cure. Once cured, remove mechanically. Storage Store below 30°C in a cool, dry place Unopened shelf life 12 months from date of manufacture Technical details Technology Moisture curing silyl modified polymer Colour Clear Packaging Cartridge 290 mL Density Approx. 1.05 g per mL Skin time at 23°C and 50 percent RH About 45 minutes Tack free time at 23°C and 50 percent RH About 60 minutes Cure rate at 23°C and 50 percent RH 2.5 to 3.5 mm per 24 hours Shore A hardness 35 ± 5 Tensile strength 1.7 MPa Elongation at break 240 percent Movement capability ± 12.5 percent Application temperature 5 to 35°C Service temperature ?20 to 70°C VOC content Approx. 35 g per L VOC classification Meets Green Building Council of Australia limits for general purpose and architectural sealants Good to know Better extrudability and curing from 5°C and above Non bubbling and non slumping formulation Sandable when fully cured Limitations Not for permanent water immersion Not for Polyethylene, Polypropylene or PTFE Not for structural glazing Follow all safety directions. For first aid and handling information refer to the product SDS.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $20.74

  • Packshot of Bastion Bond Breaker Joint Sealant 300ml

    Bastion Bastion Bond Breaker Joint Sealant 300ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Bastion Bond Breaker Joint Sealant Professional silicone bond breaker for wet areas. Create a flexible, waterproof separation at wall to wall and wall to floor junctions so your membrane and tile system can move without cracking. Ideal for bathrooms, showers, laundries and balconies. Why choose this sealant Permanently flexible to absorb movement in corners and junctions Neutral cure silicone suitable for use with most waterproofing membranes Low odour, low VOC, indoor use friendly Excellent adhesion to common building materials including concrete, masonry, ceramic tile, porcelain and most metals Water resistant once cured and designed for wet area applications Easy to gun out and tool for a smooth finish Typical uses Forming a bond breaker fillet in shower bases, bathrooms and laundries before waterproofing Movement joints at internal corners prior to tiling General wet area sealing where a flexible joint is needed Surface preparation Ensure surfaces are clean, dry and free from dust, oil, loose material and old sealant. Mask adjacent edges for a neat finish if required. For wide gaps, insert backing rod to control sealant depth. How to apply Cut the cartridge nozzle to the desired bead size and load into a standard caulking gun. Gun a continuous bead into the corner or joint. Aim for a smooth cove fillet in the 5 to 12 mm range. Tool the bead with a spatula or rounded tool to compact and shape it. Remove masking tape while the sealant is still wet. Allow the bond breaker to skin before applying compatible waterproofing membranes over the area. Follow your membrane manufacturer’s recoat time. Cure and finishing Skin time is typically minutes depending on temperature and humidity. Full cure occurs over 24 to 48 hours for standard beads. Thicker sections require longer. After the membrane has cured, complete tiling and finish perimeter joints with a sanitary grade silicone. Clean up Wipe away excess immediately with a clean cloth. Once cured, remove mechanically by trimming and peeling. Handy tips Not paintable. If painting is required, paint adjacent surfaces before sealing. Always use backing rod for large joints to control sealant depth and reduce three sided adhesion. Pre test on sensitive or natural stone surfaces. Do not use in continuously immersed conditions or for structural glazing. Storage and packaging Cartridge size: 300 mL Store upright in a cool, dry place. Use before the best by date printed on the cartridge. Safety Use in a well ventilated area. Avoid contact with skin and eyes. Keep out of reach of children. Refer to the product label for first aid directions. In the box 1 x 300 mL cartridge of Bastion Bond Breaker Joint Sealant 1 x application nozzle

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $10.85

  • Packshot of Dunlop FC Polyurethane Flexible Joint Sealant 300ml

    Dunlop Dunlop FC Polyurethane Flexible Joint Sealant 300ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop FC Joint Sealant Dunlop FC Joint Sealant is a premium, ultra flexible, moisture curing polyurethane sealant designed for jointing fibre cement, blueboard and compressed fibre cement sheets. The non slump formula handles joints up to 40 mm wide with a movement capability of plus or minus 25 percent. It is easy to apply, solvent free and isocyanate free. Colour: Grey. Why choose this sealant High flexibility for dynamic joints Non slump for clean, accurate beads on vertical and horizontal surfaces Solvent free and isocyanate free Paintable after curing Reliable performance supported by a 10 year guarantee Ideal uses Joints in fibre cement, blueboard and compressed fibre cement sheets Facade and cladding joints where movement is expected General building joints up to 40 mm width Compatible surfaces Adheres to most common construction substrates, including: Fibre cement sheets and blueboard Precast concrete panels, blockwork and bricks Sandstone and granite Fibreglass Plasterboard Technical details Movement capability ± 25% Joint width Up to 40 mm Skin time Approximately 35 minutes at 23°C and 50% RH Tack free time Approximately 1 hour at 23°C and 50% RH Cure rate About 2.5 mm per 24 hours at 23°C and 50% RH Application temperature 10°C to 35°C Clean up Warm water immediately after use Shelf life 12 months unopened, stored cool and dry Finish Paintable when dry. Can be overcoated with paint or texture coats. Colour Grey Surface preparation Ensure surfaces are clean and dry, free of dust, oil, grease, salt, mould, release agents and any contaminants that may affect adhesion. Mask adjacent areas to keep lines neat. Follow sheet fixing instructions from the board manufacturer. How to apply Cut the nozzle at a sharp angle slightly wider than the desired bead or joint width. Use a suitable backing rod where required to control depth. Aim for a joint depth equal to half the joint width. Gun the sealant into the joint and tool within 10 minutes using a round spatula to ensure full contact with the joint sides. Curing times increase in cold or humid conditions. Safety and handling Avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection. Ensure adequate ventilation during application. Keep out of reach of children. Refer to the product SDS for full safety guidance. Guarantee Backed by a 10 year guarantee when used as directed.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $21.58

  • Packshot of Selleys Roof & Gutter Silicone Sealant Translucent 310g (3 Pack)

    Selleys Selleys Roof & Gutter Silicone Sealant Translucent 310g (3 Pack)

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $46.22

  • Packshot of Selleys Wet Area Waterproof Silicone Sealant White 300g (3 Pack)

    Selleys Selleys Wet Area Waterproof Silicone Sealant White 300g (3 Pack)

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. Safety Tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $47.44

  • Packshot of Crommelin Hybrid MS Polyurethane Flexible Sealant 300ml

    Crommelin Crommelin Hybrid MS Polyurethane Flexible Sealant 300ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Crommelin Hybrid MS Polyurethane Flexible Sealant 300ml Take on interior and exterior sealing with a professional grade hybrid MS polyurethane. This single component sealant delivers a flexible, durable seal on common building substrates and is suitable for a wide range of construction and maintenance tasks. Key benefits Very low VOC and isocyanate free UV resistant for long term outdoor performance High flexibility to accommodate joint movement Excellent adhesion on properly prepared porous and non porous surfaces Easy to gun, tool and clean up Typical applications Construction and expansion joints Perimeter sealing around windows and doors Roofing and cladding laps, flashings and penetrations General gap sealing in wet and dry areas Suitable substrates Concrete, masonry, brick and render Timber and fibre cement Metals and coated metals Many plastics* and glass *Always pre test for compatibility and adhesion. Surface preparation Surfaces must be clean, dry, sound and free of dust, oil, release agents and loose material. Remove old sealant and contaminants. Abrade dense or glossy surfaces if required. Use suitable primer if specified for difficult or highly porous substrates. Mask edges for neat joints and install closed cell backing rod where needed to control joint depth. Application Cut nozzle to required bead size and load cartridge into a quality caulking gun. Gun a continuous bead into the joint ensuring full contact with sides and backing. Tool off with a moistened spatula for a smooth finish before skin forms. Protect from water and disturbance during initial cure. Clean up Clean tools and fresh spills promptly. Once cured, remove by mechanical means. Good to know Low odour formulation suitable for indoor use with ventilation. Paintable with many water based coatings once skinned and cured. Always test first. Store upright in a cool, dry place. Keep out of direct sunlight. Safety Wear suitable gloves and eye protection. Avoid contact with skin and eyes. If contact occurs, rinse with clean water. Refer to the product Safety Data Sheet for full precautions. What’s in the box 1 x 300ml cartridge 1 x application nozzle

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $15.15

  • Packshot of Selleys Liquid Nails Fast Grab Construction Adhesive 420g (20 Pack)

    Selleys Selleys Liquid Nails Fast Grab Construction Adhesive 420g (20 Pack)

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load): – At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area – At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $143.34

  • Packshot of Aftek MDF Adhesive 250ml

    Aftek Aftek MDF Adhesive 250ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Aftek MDF Adhesive 250 ml Overview Aftek MDF Adhesive 250 ml is a high quality fast setting MDF adhesive set designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials MDF timber trims decorative profiles Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Use in ventilated areas between 10°C and 30°C. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Activator accelerates set in seconds to minutes. Full strength develops over several hours. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Remove overspray and uncured adhesive with suitable solvent. Use carefully to avoid staining. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $8.37

  • Packshot of Poly Ultra Nails Construction Adhesive 320g

    Poly Poly Ultra Nails Construction Adhesive 320g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Poly Ultra Nails Construction Adhesive is a high strength, versatile adhesive designed for bonding a wide range of building materials both indoors and outdoors. It offers exceptional adhesion, easy application, and water resistance, making it a reliable choice for construction and renovation projects. Features High strength bonding suitable for multiple materials Repositionable for up to 20 minutes for precise alignment Waterproof once cured Ready to use straight from the cartridge Brown finish for a natural look Suitable Materials Concrete, brick, plasterboard, ceramics Plywood, particle board, aluminium Hardwood, softwood, steel, fibreglass Some plastics (pre-test recommended) Application Instructions Ensure surfaces are clean, dry, and free from dust, grease, or flaking paint. Cut the seal, fit the nozzle, and cut to the desired bead size. Insert into a caulking gun. For wall panelling and sheet flooring, apply 6mm beads along studs or joists in a zig-zag line at 40cm intervals. Bring surfaces together within 10 minutes and press firmly along glue lines. Reposition if needed within 20 minutes. Fix with nails, screws, or clamps for at least 24 hours to ensure bond strength. For contact bonding, apply to one surface, bring together, then separate for 3–5 minutes before rejoining. Clean tools and excess adhesive with mineral turpentine. Technical Information Coverage: Approximately 15 metres of 5mm bead Initial bond: Within 24 hours at 25°C Full cure: Up to 7 days Colour: Brown Important Notes Not suitable for mirrors, polystyrene foam, or continuous water immersion Avoid use on copper-based metals or metals exposed to direct sunlight heat Do not use for tightly clamped joints or heavy loads without mechanical fasteners Safety Information Use in a well-ventilated area and avoid breathing vapours Wear protective gloves and eye protection Keep away from heat, sparks, and open flames Keep out of reach of children If swallowed, do not induce vomiting — contact a doctor or Poisons Information Centre (AUST 131 126; NZ 0800 764 766) Contains 30% w/w liquid hydrocarbons

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $4.85

  • Packshot of Selleys Araldite Extra Time Epoxy Adhesive 200ml

    Selleys Selleys Araldite Extra Time Epoxy Adhesive 200ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Araldite Extra Time Epoxy Adhesive 200ml Araldite Extra Time is a strong two part epoxy that gives you an extended working time of up to 60 minutes. It is ideal for complex or multi piece assemblies where accurate positioning matters. Once cured it forms a tough, durable bond that dries translucent. Why you will love it Extended working time of 60 minutes for precise assembly Holds up to 150 kg per cm² when fully cured on clean, abraded steel Dries translucent for a neat finish Versatile bonding across common materials Suitable materials Wood, metal, masonry, china, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. Pre test on leather and rubber for suitability. Typical uses Furniture repairs and assemblies Fixing metal or timber components General household, hobby, and craft bonding Repairs on masonry, ceramics, and glass where a clear finish is preferred Directions Surface prep: abrade, clean, and dry both surfaces. Pierce each tube using the spike in the cap. Dispense equal parts onto a clean disposable surface. Mix thoroughly. Leave for 5 minutes, then mix again before applying. Mixed glue is usable for about 1 hour at 20°C. Do not use the plastic blister to mix. Apply to both surfaces and join. Support if needed to prevent movement. Avoid strain for 6 to 8 hours. Full strength develops after 24 to 72 hours depending on conditions. Replace caps on the correct tubes to avoid cross contamination. Clean up Wipe away uncured adhesive with acetone. Once cured, mechanical removal is required. Key specs Technology Two part epoxy Working time Up to 60 minutes Initial handling 6 to 8 hours Full cure 24 to 72 hours Bond strength Up to 150 kg per cm² on abraded steel when fully cured Appearance Dries translucent Temperature resistance Up to 80°C. Bond may soften above this but strength returns when temperature normalises. Pack size 200 ml Good to know Allow longer bonding times in colder weather. Product may discolor with UV exposure. Store in a cool dry place.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $66.48

  • Packshot of UNi-PRO Cornice Adhesive 2.5kg

    Uni-Pro UNi-PRO Cornice Adhesive 2.5kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    UNi-PRO Cornice Adhesive 2.5 kg Overview UNi-PRO Cornice Adhesive 2.5 kg is a high quality cornice adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials plaster cornice plasterboard masonry Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Apply between 10°C and 30°C in dry, draft free conditions. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Sets firm to hold cornice in place, full cure over 24 hours or as directed. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Wipe away fresh adhesive with a damp cloth. Scrape away set material carefully. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $19.75

  • Packshot of Selleys Araldite Rapid Epoxy Adhesive 14mL

    Selleys Selleys Araldite Rapid Epoxy Adhesive 14mL

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Araldite Rapid Epoxy Adhesive 14 mL Fast-setting, two-part epoxy for quick, durable repairs at home, in the workshop, or on site. The self-mixing syringe makes application clean and precise, setting in about 90 seconds and reaching handling strength soon after. Dries translucent for a neat finish. Key benefits Sets in approximately 90 seconds for rapid fixes High strength bond up to 75 kg/cm² when fully cured Dries translucent for low-visibility repairs Self-mixing nozzle for easy, accurate application Versatile bonding across common materials Best for Everyday repairs and small assemblies Fixing chipped ceramics and china Metal, glass, leather, rubber, and many plastics Suitable materials China, metal, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. How to use Prep Abrade, clean, and dry both surfaces. Attach nozzle Remove cap, fit and lock the self-mixing nozzle, then purge a small amount until evenly mixed. Apply Spread adhesive on both surfaces and join within 1 minute. Hold Support the bond for about 10 minutes to prevent movement. Cure Maximum strength develops after about 16 hours. Allow longer in cold conditions. Clean up Wipe away uncured adhesive with acetone. Remove and dispose of the used mixing nozzle before the adhesive sets in the tip. Technical details Technology Two-part epoxy Set time About 90 seconds Handling time Approximately 10 minutes Full cure About 16 hours Colour when dry Translucent Temperature resistance Up to 60 °C Pack size 14 mL self-mixing syringe Good to know Bond may soften above 60 °C and regains strength when cooled. Pre-test on leather and rubber to confirm suitability. May discolor with prolonged UV exposure. Store in a cool, dry place. Replace cap after removing the used nozzle. Safety Follow the safety directions on the packaging. Use in a well-ventilated area and avoid skin contact. Keep out of reach of children.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $16.89

  • Packshot of SikaBond High-Strength Foam Construction Adhesive 750 mL

    Sika SikaBond High-Strength Foam Construction Adhesive 750 mL

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    SikaBond High-Strength Foam Construction Adhesive 750 mL is a reliable one component foam construction adhesive dispensed from a can chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 750 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Sika High-Strength for your next project Everyday jobs often involve mixed materials and imperfect surfaces. SikaBond High-Strength Foam Construction Adhesive 750 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Fixing studs, battens, and sheets Filling small gaps while bonding Fast installation where speed saves labour Suitable surfaces The adhesive works well on the following surface types when properly prepared: Timber and masonry Concrete and fibre cement Many building materials except PE and PP Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of assemble parts within the open time to ensure a strong bond. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Expands slightly to fill gaps, then cures to a firm, high strength foam. Provides excellent initial grab and reduces the need for nails in many applications. Temperature and environmental performance Apply within the can's specified temperature range. Humidity supports foam curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured foam with the prescribed cleaner. Once cured, cut back mechanically. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store cans upright. Do not expose to heat. Observe transport and disposal rules for pressurised containers. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $31.50

  • Packshot of Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL

    Selleys Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL is a reliable two part fast setting epoxy adhesive for durable repairs chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 24 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Tarzan's Grip Grip for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Household and workshop repairs that need speed and strength Fixing fixtures, brackets, and hardware Filling chips and rebuilding small edges before sanding Suitable surfaces The adhesive works well on the following surface types when properly prepared: Metal hardware Ceramic tiles Most rigid plastics except polyethylene and polypropylene Timber and MDF Stone and concrete Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of 3 to 5 minutes working time. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Initial set is reached in about 5 minutes at 23 C. Sandable after several hours. Achieves high final strength after a full overnight cure. Temperature and environmental performance Performs well across typical domestic temperature ranges after cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured excess with acetone on a cloth. Use care on painted substrates. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed to prevent crystallisation. Store upright at moderate temperature. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $11.50

  • Bostik Repair All Multi-Purpose Adhesive 20ml Bostik Repair All Multi-Purpose Adhesive 20ml

    Bostik Bostik Repair All Multi-Purpose Adhesive 20ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Bostik Repair All is a clear, multi-purpose adhesive for quick, durable repairs around the home, garage, and workshop. It bonds strongly, remains slightly flexible, and is water resistant once cured, making it suitable for everyday fixes and craft projects. Why you will love it Strong, long lasting bond Dries clear for a neat finish Water resistant once fully cured Flexible bond helps absorb vibration Suitable for indoor and outdoor use Works on Metal, wood, ceramics, glass, most rigid plastics, rubber, leather, fabric, and more. Always test on delicate or unknown materials first. Ideal for Household repairs and DIY Craft, hobbies, and school projects Fixing ornaments, toys, trims, and fittings Directions Ensure surfaces are clean, dry, and free of dust or grease. Lightly roughen smooth surfaces. Apply a thin even layer to one surface. Join parts together and press firmly. Support or clamp if needed. Wipe away any squeeze out immediately with a cloth dampened with solvent suitable for the substrate. Allow to set undisturbed. Handling strength is typically reached within hours. Full cure is usually achieved after 24 hours depending on bead size, temperature, and humidity. Clean up Uncured adhesive can be removed with a suitable solvent. Cured adhesive is best removed mechanically by trimming or carefully scraping. Good to know Not recommended for polyethylene, polypropylene, PTFE, or surfaces that will be in constant water immersion. Avoid contact with food or drinking water surfaces. Store upright in a cool dry place with cap tightly closed. Key details Brand Bostik Product Repair All Appearance Clear when dry Finish Flexible Water Resistance Yes, once cured Pack Size 20ml Always read the label and follow safety instructions. Keep out of reach of children.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $14.50

  • Bostik HG3 Glue Gun Refills Clear Adhesive Sticks 10 Pack

    Bostik Bostik HG3 Glue Gun Refills Clear Adhesive Sticks 10 Pack

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Keep your glue gun ready for any project with the Bostik HG3 Glue Gun Refills. These high quality hot melt sticks provide a smooth, even flow for clean and reliable bonding. Pack of 10 clear adhesive sticks Compatible with Bostik HG3 Glue Gun Creates a strong, flexible and transparent bond Suitable for wood, plastic, fabric, leather, ceramics and more Perfect for craft work, household repairs and DIY projects. The hot melt formula ensures quick adhesion with minimal mess, giving you professional results every time. How to use: Insert a glue stick into the back of your glue gun. Allow the gun to heat for a few minutes before use. Apply steady pressure on the trigger to release glue. Join surfaces immediately for best results. Let the glue cool completely before handling. Safety Information: Hot glue can cause burns. Avoid contact with skin and eyes. Keep out of reach of children. The Bostik HG3 Glue Gun Refills are ideal for quick fixes, decorative projects and reliable everyday bonding.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $15.21

  • Selleys Liquid Nails Fast Grab Construction Adhesive 420g - 3 Pack

    Selleys Selleys Liquid Nails Fast Grab Construction Adhesive 420g - 3 Pack

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load):– At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area– At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $21.74

  • Dunlop Ready-to-Go Coloured Grout, Anti-Mould No-Mix - 800g Dunlop Ready-to-Go Coloured Grout, Anti-Mould No-Mix - 800g

    Dunlop Dunlop Ready-to-Go Coloured Grout, Anti-Mould No-Mix - 800g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Ready-to-Go Coloured Grout is a premium, pre-mixed grout for fast, clean results on walls and floors. No mixing, no mess, just open, apply, and buff for a smooth, long-lasting finish. The formula includes Grout Shield for anti-mould and anti-bacterial protection to help surfaces stay cleaner for longer. Suitable for interior and exterior applications, and available in a wide colour range to match or contrast your tiles. Ready-mixed convenience, apply straight from the tub Contains Grout Shield for mould and bacteria resistance Use on walls & floors, indoors & outdoors* Ideal for joint widths from 1–5 mm Great for rejuvenating old grout (min. removal depth: 1 mm walls, 2 mm floors) *Always follow the data sheet guidance for your specific area and exposure. Where to Use Ceramic, porcelain and most glazed tiles Bathrooms, kitchens, splashbacks, laundries, living areas Light-duty exterior tiled areas (check exposure & substrate) This grout is designed for typical domestic and light commercial tiling where a smooth, uniform finish is desired. Colours & Finish Available in a contemporary colour palette (e.g. whites and greys) to complement most tile styles. Use Dunlop’s colour selector to visualise combinations before you start. Coverage Coverage varies by tile size, joint width and depth. As a guide (per kg) of grout: Tile size (L×W×Thickness) Joint width 1.5 mm Joint width 3 mm Joint width 5 mm 25×25×4 mm mosaics ≈1.04 m²/kg ≈0.52 m²/kg ≈0.31 m²/kg 100×100×8 mm ≈2.08 m²/kg ≈1.04 m²/kg ≈0.63 m²/kg 200×200×8 mm ≈4.17 m²/kg ≈2.08 m²/kg ≈1.25 m²/kg Tip: Allow an extra 10–15% for wastage due to technique, tile type and site conditions. Directions (Summary) Prep: Ensure joints are clean, dry, and free from dust, adhesive residue and contaminants. For rejuvenation, remove at least 1 mm (walls) or 2 mm (floors) of old grout. Apply: Using a rubber grout float, force grout firmly into joints at a 45° angle. Strike & shape: Allow grout to firm in the joint (~15 mins). Shape joints as required. Clean: Wipe diagonally with a dense, damp sponge, rinsing frequently. Use minimal water to reduce shade variation and shrinkage. Buff: When touch-dry (typically 6–24 hrs), buff tile faces with a clean, dry cloth. Drying & Use Initial set at ~24 hrs at 23 °C / 50% RH Shower walls can be exposed to water after ~24 hrs Clean-Up & Storage Clean tools and residue with water while the grout is still wet. Reseal the tub between uses to prevent skinning. Store upright in a cool, dry place. Safety Read the Safety Data Sheet before use and follow PPE guidance. Avoid contact with eyes and prolonged skin contact. Keep out of reach of children.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $16.30 $0.02/g

  • Earl's MulTflex Exterior Flexible Filler Timber & Masonry, Paintable, Non-Shrink, No VOCs Earl's MulTflex Exterior Flexible Filler Timber & Masonry, Paintable, Non-Shrink, No VOCs

    Timbermate Earl's MulTflex Exterior Flexible Filler Timber & Masonry, Paintable, Non-Shrink, No VOCs

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Earl’s MulTflex® Exterior Flexible Filler is a unique, single-pack, ready-to-use flexible filler and adhesive formulated for lasting repairs on timber and masonry. It delivers a durable, non-shrinking, non-sinking finish that won’t crack with vibration and won’t fall out, making it ideal for exterior maintenance where movement and weather can defeat ordinary fillers. Paintable when dry and formulated with no volatile organic compounds (No VOCs), it’s a dependable, low-odour solution for professional results at home or on site. Proudly 100% Australian made and owned. Why you’ll love it Exterior-grade flexibility: absorbs movement and vibration without cracking. Non-shrink & non-sink: holds profile and edge detail after cure. Won’t fall out: engineered adhesion for long-term durability. Ready to use: straight from the tub — no mixing, no mess, no waste. Paintable: achieves a seamless, colour-matched finish once dry. No VOCs: low odour, solvent-free formula. Interior / Exterior: versatile enough for both. Proudly Australian: made and owned in Australia. Where it works Use Earl’s MulTflex® to repair and rebuild on a wide range of common building substrates: Timber: decks, window frames, trims, fascia, general carpentry repairs. Masonry: brick, block, render and patching mortar-like defects. Plasterboard: exterior-exposed linings under cover and general patching. Metals & gutters: non-structural filling and profiling (clean, sound, free of rust). Around pipes & penetrations: neat, gap-free finishing before painting. Glass & surrounds: edge repairs and feathering prior to topcoating. Ideal projects Rebuilding weathered or rotten timber edges before repainting. Filling cracks and surface imperfections in rendered walls. Profiling and feathering joints and transitions for a paint-ready finish. General exterior maintenance where a flexible, paintable filler is essential. Directions Surface Preparation Remove loose or flaking material, dirt, dust, oil, grease and chalky paint. Substrates must be sound. Ensure surfaces are dry and free from visible moisture. Treat rust and stabilize friable areas as required. For best mechanical key, lightly abrade glossy surfaces and remove dust. Application Open the tub and use directly. If the surface of the product begins to dry, add a few drops of water and re-mix gently. Keep the container tightly sealed when not in use. Apply with a filling knife or trowel, pressing firmly to ensure full contact with the substrate. Build up in thin layers for deep repairs, allowing each layer to firm before adding the next. For a satin-smooth finish, tool the final pass with a wet knife or brush to reduce post-work finishing. Finishing & Painting Allow to dry fully. Dry time varies with film thickness, temperature and humidity. Once dry, apply a suitable primer/undercoat if required by your paint system, then topcoat. Use quality exterior paints for weather-exposed areas. Clean-Up & Storage Clean tools and splashes with water while wet. Reseal immediately after use to minimise skinning and reduce waste. Store upright with lid sealed. Do not allow contents to dry out. Good to know Formulation is unaffected by normal temperature swings and resists cracking with vibration. Designed for exterior flexibility yet also suitable for interior touch-ups. For best results on deep voids, fill in multiple light applications rather than one heavy pass. Specifications Brand Earl’s Product MulTflex® Exterior Flexible Filler Type Single-pack, ready-to-use flexible filler & adhesive Use Interior / Exterior Paintable Yes, once fully dry VOC Content No VOCs (as supplied) Shrink / Sink Non-shrinking, non-sinking Flexibility Resists cracking with vibration and movement Clean-Up Water (while wet) Substrates Timber, masonry, render, plasterboard, metals, gutters, around pipes, glass Finish Satin-smooth when tooled with a wet knife or brush Packaging Ready-to-use tub Country of Origin 100% Australian made & owned Limitations Do not apply to unsound, dusty or actively corroding surfaces without proper preparation. Dry and cure times depend on depth and conditions; confirm dryness before painting. Not intended for structural repairs. Pro Tips Feather edges wide for invisible paint blending on weathered timber and render. Keep a small cup of clean water nearby to maintain a smooth final pass. Deep cavities: bridge with successive thin layers for the most stable result.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $19.00 - $28.00

  • Earl’s Powder Putty – Mix-to-Use Interior & Exterior Filler (No Waste, Easy Sand) Earl’s Powder Putty – Mix-to-Use Interior & Exterior Filler (No Waste, Easy Sand)

    Timbermate Earl’s Powder Putty – Mix-to-Use Interior & Exterior Filler (No Waste, Easy Sand)

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Earl’s Powder Putty – Mix-to-Use Interior & Exterior Filler Earl’s Powder Putty is a multi-purpose powder filler for professional and DIY repairs. Just add water, mix only what you need, and achieve a tough, easy-sand finish with no waste and no shrinking. Brand: Earl’s Interior and exterior use* Mix-on-demand convenience Non-shrinking, smooth finish Easy sanding and shaping Indefinite shelf life in dry powder form Proudly made in Australia *Exterior applications must be sealed/painted and used on stable substrates. About Earl’s Powder Putty Earl’s Powder Putty delivers reliable, high-quality filling for timber, walls, masonry and metal. Because it’s supplied as a dry powder, you can tailor the mix to your task—stiffer for knife-grade filling and sculpting, or looser for fine skim work. The result is a hardwearing repair that sands easily and accepts coatings beautifully. Where Earl’s Powder Putty Works Timber & woodwork: doors, frames, skirting, architraves, furniture, cabinetry Walls & panels: plasterboard and cement sheeting patching and feathering Masonry & concrete: chips, small holes and surface imperfections Metals: minor dents and irregularities prior to priming and painting Floor preparation: quick patching of distressed boards prior to covering Craft & hobby: architectural details, mouldings and small sculpting tasks Why Choose Earl’s No shrink: Formulated to dry without shrinking for flush, invisible repairs. Mix what you need: Reduce waste and always work with a fresh batch. Shapes perfectly: Once dry, Earl’s Powder Putty can be cut, carved, sanded or sawn. Paint-ready: Accepts primers and topcoats after proper dry and prep. Economical & dependable: Indefinite shelf life in powder form when stored dry. Directions for Earl’s Powder Putty Surface prep: Ensure the area is clean, dry and sound. Remove loose material, dust, grease and contaminants. Key glossy surfaces for better adhesion. Mix: In a clean container, add Earl’s Powder Putty and slowly incorporate clean water. Stir to a smooth, lump-free paste. Adjust water to suit the task. Apply: Press the mix firmly into the repair with a putty knife or trowel. Slightly overfill to allow for sanding back flush. Build: For deep repairs, apply in layers, allowing each to firm before adding the next. Finish: Once dry, sand smooth. The cured filler can be carved or sawn to refine edges and profiles. Coat: Prime/seal and paint after full dry. For exterior use, always seal with suitable coatings. Clean-up: Clean tools with water while the product is still wet. Dry and recoat times vary with temperature, humidity and film thickness. Allow extra time in cool or damp conditions and for deep fills. Good to Know About Earl’s Not waterproof by itself: Water and weather resistance requires sealing/painting. Not flexible: Avoid use where movement, vibration or structural flexing is expected. Stable substrates only: Ensure exterior bases are sound and well prepared. Storage: Keep Earl’s Powder Putty dry and tightly closed. Moisture exposure can reduce performance after opening. Safety: Avoid dust during mixing and sanding. Use PPE and adequate ventilation. Typical Earl’s Applications Filling nail and screw holes, chips and minor cracks Skim patching and feathering edges prior to painting Rebuilding small decorative profiles and mouldings Levelling minor surface imperfections before finishing Specifications Brand Earl’s Product Name Earl’s Powder Putty Product Type Multi-purpose powder filler Format Dry powder; mix with clean water Colour (dry) Off-white to white; paintable Use Areas Interior and exterior* (exterior must be sealed/painted; stable substrates only) Substrate Compatibility Wood, plasterboard, cement sheeting, concrete, masonry, properly prepared metal Shrinkage Non-shrinking when used as directed Sandability Easy sanding once fully dry Paintability Prime/seal and paint after full dry Water Resistance Requires sealing; product itself is not waterproof Shelf Life (powder) Indefinite when stored cool, dry and sealed Clean-up Water while wet Tools Putty knife, trowel, mixing stick or paddle, sanding block Country of Origin Australia Limitations of Earl’s Powder Putty Do not use as a flexible gap filler or where structural movement is expected. Always prime/seal before exposure to moisture or exterior weather. Deep repairs may require multiple layers with adequate drying between coats. Not for permanently wet, submerged or high-movement joints. FAQs – Earl’s Powder Putty Can I mix a large batch and store it?Mix only what you can use within the working time. Discard any mix that begins to stiffen or set. Can I screw or nail into it?For non-structural tasks, light fixings may be possible in sufficiently thick, fully cured areas. Pre-drill as needed and test first. Is it paintable?Yes. Once dry and sanded, prime or seal the repair and finish with your chosen coating system. Always follow label directions. Test on a small, inconspicuous area to confirm compatibility and finish.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $10.50 - $81.00

  • Agnews Water Putty - Multi-Purpose Filler & Floor Leveler (Interior/Exterior Grade) Agnews Water Putty - Multi-Purpose Filler & Floor Leveler (Interior/Exterior Grade)

    Timbermate Agnews Water Putty - Multi-Purpose Filler & Floor Leveler (Interior/Exterior Grade)

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Agnews Water Putty - Hard-Setting Filler for Wood, Plasterboard, Concrete & More Agnews Water Putty is a professional, powder-based repair and levelling compound for durable, long-lasting results. Mix only what you need with clean water, then patch, level or rebuild surfaces with confidence. Once cured, it sets rock hard, bonds permanently, and can be sawn, drilled and sanded to a smooth, paint-ready finish. Key features Brand: Agnews Unlimited shelf life when stored dry Non cracking, non shrinking, non sinking Won't fall out – adheres firmly and fills to any depth Interior & exterior grade (seal exterior applications after full dry) Non flammable and no VOCs Mix what you need for minimal waste Suitable substrates Plasterboard, concrete, wood/timber, cement sheet, masonry. Also suitable for minor floor levelling and feathering on concrete, timber and ceramic tile substrates. Typical applications Fill holes in wood: knotholes, nail and screw holes, dents, edge build-ups Wall patching: cracks and cavities in plasterboard and cement sheet Furniture repair: tighten loose joints, reset fasteners, rebuild profiles Floor levelling: ramp or smooth minor level variations before floor coverings Trim and fixtures: refit loose door bumpers and trims with reliable hold Architectural & hobby moulding: casting and shaping durable components Why choose Agnews Agnews Water Putty cures to a dense, stone-hard finish that resists shrinkage and cracking even in deep fills. It bonds securely, stays put, and finishes cleanly, delivering a stable base for sanding, priming and painting. From small touch-ups to larger restorations, it provides consistent, professional results. Directions (general guide) Surface prep: Ensure the area is clean, dry, sound and free of dust, oil or loose material. For very porous substrates, lightly dampen to reduce rapid suction. Mix: Add powder to clean water and blend to a smooth, lump-free paste. Adjust water to suit application (thicker for filling, looser for fairing/skim). Apply: Press firmly into cracks or voids with a putty knife or trowel. Overfill slightly so you can sand back flush. Cure: Allow to dry thoroughly. Dry time varies with thickness, temperature and humidity. Finish: Sand to profile. Prime and paint or seal. For exterior applications, always seal after full dry. Exterior use guidance This is a hard-setting, non-flexible compound. For exterior use, only apply over stable substrates with minimal expansion and contraction from temperature changes. Ensure the putty is fully dry before sealing with a suitable exterior-grade coating. Finishing & compatibility Paintable and sealable after full dry; prime as required for best results. Can be cut, carved, drilled and sanded after cure without crumbling. For stained timber finishes, test a small area first for colour and absorption. Pro tips Mix small batches and use promptly. For deep voids, apply in layers if needed, allowing each layer to firm before the next. Store powder in a cool, dry place to maintain its unlimited shelf life. Clean tools with water before material cures. At a glance Substrates: plasterboard, concrete, wood/timber, cement sheet, masonry Uses: patching, levelling, rebuilding, moulding Properties: non cracking, non shrinking, non sinking, non flammable, no VOCs Finish: hard, dense, smooth and paint-ready after sanding/priming

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $7.00 - $40.00

  • Bostik General Purpose Neutral Cure Silicone Sealant 20ml – Clear, Flexible & Waterproof Bostik General Purpose Neutral Cure Silicone Sealant 20ml – Clear, Flexible & Waterproof

    Bostik Bostik General Purpose Neutral Cure Silicone Sealant 20ml – Clear, Flexible & Waterproof

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Overview This high-quality general-purpose silicone sealant is a versatile solution for a wide range of sealing and bonding applications. Engineered with neutral cure technology, it is designed to provide a durable, flexible, and weather-resistant seal that remains reliable even in demanding environments. Once cured, the sealant forms a strong rubber-like finish that is permanently elastic, ensuring long-lasting performance both indoors and outdoors. Key Features Neutral Cure Technology: Low-odor curing system suitable for sensitive applications. Permanently Flexible: Retains elasticity over time without cracking or shrinking. Waterproof Protection: Provides a watertight seal, protecting against leaks and moisture ingress. Interior & Exterior Use: Unaffected by rain, snow, extreme temperatures, or prolonged UV exposure. Excellent Adhesion: Bonds strongly to most common building materials without primer. Easy Application: Smooth flow from the tube, easy to tool and clean before curing. Applications This sealant is designed for general-purpose use across a variety of materials and environments. Its flexibility and adhesion make it suitable for: Sealing around window and door frames. Lap joints in metal guttering and roofing sheets. Bonding panels such as wood, plasterboard, insulation board, and drywall. Fixing masonry joints including sills, brickwork, and decorative trims. Gap filling around pipes, conduits, and penetration surfaces. General sealing in kitchens, bathrooms, and living areas where flexibility is required. Limitations Not suitable for permanent water immersion (e.g., underwater joints or continuous water load). Not recommended for use on polyethylene (PE), polypropylene (PP), polycarbonate (PC), polymethyl methacrylate (PMMA), PTFE, neoprene, bituminous surfaces, or very soft plastics. Not intended for deep cavity filling without adequate moisture for curing. Surface Preparation To ensure maximum performance, surfaces must be clean, dry, and free from dust, grease, or loose particles. Non-porous surfaces should be wiped with solvent and dried with a clean cloth. Porous surfaces should be lightly abraded or brushed to remove contaminants and improve adhesion. Complete any painting work before applying the sealant. Application Instructions Remove the cap and pierce the nozzle seal. Apply steadily along the joint or surface, ensuring continuous contact. Smooth or tool the bead before skin formation occurs. If masking tape is used, remove immediately after tooling to avoid tearing the cured seal. Curing At room temperature (23°C), the sealant will skin over within 15 minutes and achieve full cure within 24 hours, depending on humidity and joint depth. Once cured, it provides a permanently flexible and weatherproof joint. Cleaning & Maintenance Excess uncured sealant can be cleaned using a cloth dampened with mineral turpentine. Fully cured material should be trimmed away carefully with a sharp blade. Store unused tubes in a cool, dry place below 25°C and away from direct sunlight. Shelf life is up to 12 months from the date of manufacture. Health & Safety Use in a well-ventilated area. Avoid contact with eyes and mucous membranes, as uncured sealant may cause irritation. In case of contact with eyes, flush thoroughly with water and seek medical advice. Keep out of reach of children. Always follow safety instructions and refer to the product’s safety data for detailed guidance. Why Choose This General Purpose Silicone Sealant? This sealant is a trusted choice for tradespeople, DIY enthusiasts, and homeowners seeking a reliable solution for everyday sealing needs. Its combination of flexibility, adhesion, and weather resistance ensures that once applied, it continues to protect and bond effectively for years to come. Whether you are fixing a leaking gutter, sealing around windows, or bonding decorative trims, this product provides professional results with minimal effort. Technical Specifications Technology Neutral Cure Silicone Appearance Clear Paste Working Time Up to 15 minutes Tack-Free Time Approximately 15 minutes Full Cure at 23°C 24 hours Flexibility Permanently elastic after curing Weather Resistance Unaffected by rain, snow, UV, and temperature variations Applications Windows, doors, guttering, masonry, panels, pipes, decorative elements Storage Below 25°C, out of direct sunlight Shelf Life 12 months from manufacturing date

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $9.98

  • Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml [White]

    Sika Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $0.00 - $28.00

  • Sika Sikaflex Pro+ Sealant 310ml [White]

    Sika Sika Sikaflex Pro+ Sealant 310ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $24.00

  • Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Clear] Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g

    Selleys Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. Safety Tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $0.00 - $16.00

  • Uni-Pro Carbon Steel Flexible Scraper Wooden Handle 75mm

    Uni-Pro Uni-Pro Carbon Steel Flexible Scraper Wooden Handle 75mm

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    The UNi-PRO Real Good Scrapers are a comprehensive range of scrapers, perfect for DIY jobs such as removing flaky paint or silicone. The blades have been extremely durable and reliable in various weather conditions and over time. With the scraper being made from high quality German steel that has resistant to corrosion, your professional tool will last just as long as you do!

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $7.20


You have seen 48 out of 162 products

Gap Filling

High‑build, non‑sag and sandable options for filling gaps before finishing. Choose fast‑grab for vertical joints or feather‑edge compounds for smooth blending. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.

Login

Forgot your password?

Don't have an account yet?
Create account