Araldite Two-Part Epoxy Adhesive delivers maximum strength bonding for a wide range of materials. The mixed product gels in 2 hours, achieves initial bonding within 6–8 hours, and reaches full strength after 3 days. Features Chemical reaction of the two parts provides superior strength Bonds a wide variety of surfaces Dries clear for a clean finish Extremely strong and durable Highly water resistant – suitable for fixing tiles around pools (not below the waterline) Forms a rigid, long-lasting bond Fills small gaps – surfaces do not need to fit perfectly Excellent chemical and heat resistance Clamping recommended for a stronger bond Not suitable for Polypropylene or Polyethylene plastics Bond strength weakens above 80°C but recovers when cooled Appearance Translucent Where to Use Load-bearing repairs Fixing loose table or chair legs Reattaching hammer heads Bonding aluminium sheets Timber repairs on boats Repairing splits and cracks in cricket bats Bonding fibreglass sheets or skis Securing Dynabolts and metal rods into concrete Suitable Materials Glass Metal Wood Fabric Rigid plastic (except Polyethylene and Polypropylene) Crystal Leather Directions for Use Ensure all surfaces are clean, dry, and free of grease, rust, and paint. For best results, roughen smooth surfaces after cleaning. Dispense equal parts of Part A and Part B onto a clean, disposable surface (e.g. polyethylene or cardboard). Mix thoroughly using a spatula, nail, or stick. Apply immediately to both surfaces and press together. Clamp for 6–8 hours while the bond sets. Remove excess adhesive and clean tools immediately. Replace the correct caps on each tube to prevent hardening. Handy Tips Mix in small quantities for maximum working time – larger mixes cure faster. Replace caps immediately after use and wipe nozzles with acetone or nail polish remover. Do not swap caps between tubes – lids and tubes are colour coded. Uncured Araldite can be wiped off with acetone or nail polish remover. Once cured, remove mechanically by scraping or sanding – solvents will not dissolve it. To reposition a cured bond, heat gradually to 150°C (if the item is heat resistant), reposition, and allow to cool. For surface prep: use Selleys Liquid Sugar Soap on porous materials, or Methylated Spirits on non-porous surfaces. Use Selleys Kwik Strip Smart to remove tough residues if needed. Safety Tips Avoid contact with skin and eyes. Avoid breathing vapours. Do not use solvents near eyes or open wounds. In case of eye contact, rinse with water for at least 15 minutes and seek medical advice. Non-toxic once fully cured. Refer to the Material Safety Data Sheet for more details. Storage & Reuse Ensure caps are replaced tightly after use and store in a cool, dry place.
$76.88
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$18.00
Agnews Water Putty - Hard-Setting Filler for Wood, Plasterboard, Concrete & More Agnews Water Putty is a professional, powder-based repair and levelling compound for durable, long-lasting results. Mix only what you need with clean water, then patch, level or rebuild surfaces with confidence. Once cured, it sets rock hard, bonds permanently, and can be sawn, drilled and sanded to a smooth, paint-ready finish. Key features Brand: Agnews Unlimited shelf life when stored dry Non cracking, non shrinking, non sinking Won't fall out – adheres firmly and fills to any depth Interior & exterior grade (seal exterior applications after full dry) Non flammable and no VOCs Mix what you need for minimal waste Suitable substrates Plasterboard, concrete, wood/timber, cement sheet, masonry. Also suitable for minor floor levelling and feathering on concrete, timber and ceramic tile substrates. Typical applications Fill holes in wood: knotholes, nail and screw holes, dents, edge build-ups Wall patching: cracks and cavities in plasterboard and cement sheet Furniture repair: tighten loose joints, reset fasteners, rebuild profiles Floor levelling: ramp or smooth minor level variations before floor coverings Trim and fixtures: refit loose door bumpers and trims with reliable hold Architectural & hobby moulding: casting and shaping durable components Why choose Agnews Agnews Water Putty cures to a dense, stone-hard finish that resists shrinkage and cracking even in deep fills. It bonds securely, stays put, and finishes cleanly, delivering a stable base for sanding, priming and painting. From small touch-ups to larger restorations, it provides consistent, professional results. Directions (general guide) Surface prep: Ensure the area is clean, dry, sound and free of dust, oil or loose material. For very porous substrates, lightly dampen to reduce rapid suction. Mix: Add powder to clean water and blend to a smooth, lump-free paste. Adjust water to suit application (thicker for filling, looser for fairing/skim). Apply: Press firmly into cracks or voids with a putty knife or trowel. Overfill slightly so you can sand back flush. Cure: Allow to dry thoroughly. Dry time varies with thickness, temperature and humidity. Finish: Sand to profile. Prime and paint or seal. For exterior applications, always seal after full dry. Exterior use guidance This is a hard-setting, non-flexible compound. For exterior use, only apply over stable substrates with minimal expansion and contraction from temperature changes. Ensure the putty is fully dry before sealing with a suitable exterior-grade coating. Finishing & compatibility Paintable and sealable after full dry; prime as required for best results. Can be cut, carved, drilled and sanded after cure without crumbling. For stained timber finishes, test a small area first for colour and absorption. Pro tips Mix small batches and use promptly. For deep voids, apply in layers if needed, allowing each layer to firm before the next. Store powder in a cool, dry place to maintain its unlimited shelf life. Clean tools with water before material cures. At a glance Substrates: plasterboard, concrete, wood/timber, cement sheet, masonry Uses: patching, levelling, rebuilding, moulding Properties: non cracking, non shrinking, non sinking, non flammable, no VOCs Finish: hard, dense, smooth and paint-ready after sanding/priming
$7.00 - $40.00
Concremate Expanding Anchoring Cement Anchor, patch and lock in place with confidence. Concremate is a high-performance expanding cement designed for rapid, reliable anchoring and structural patching. Mixed to a workable, mortar-like consistency, it expands slightly as it cures to counteract drying shrinkage. That controlled expansion grips embedded items and surrounding material tightly, delivering a secure, long-lasting hold that stands up to strain, stress and vibration. Why choose Concremate Fast turnaround: initial set in about 30 minutes and hard in approximately 1 hour, so many jobs can progress the same day. Expands and grips: engineered expansion of about 0.125% offsets shrinkage and locks into the substrate. High ultimate strength: cures to a finish that becomes harder than standard concrete at 28 days when properly mixed and applied. Versatile application: ideal for anchoring bolts, rails, brackets and fixtures, as well as patching holes, chases and cracks. Durable performance: forms a robust, long-term bond that resists severe mechanical stress and vibration. Where it excels Use Concremate for secure embedment and structural repairs on common mineral surfaces. It is suitable for: Concrete and masonry Brickwork and stone Tiles and terrazzo Plaster and similar mineral substrates Typical projects Anchoring handrails, posts, machine base bolts, threaded rods and heavy brackets Fixing door and window hardware to masonry openings High-pressure grouting under plates, around pipe sleeves and service penetrations Patching voids, chased conduits, spalled edges and impact damage in floors, walls and ceilings How it works Concremate is a mineral-based expanding cement. After mixing with clean water, the paste hydrates and begins to set. A small, controlled expansion during cure offsets natural drying shrinkage. The result is a tight, interference-style fit that increases grip on embedded items and keys the patch into surrounding material. For best results, the material must be able to expand slightly while drying and should not be constrained in a completely sealed cavity. Directions for use Surface preparation: Remove dust, loose material, laitance, oil and contaminants. Roughen smooth surfaces and blow or brush clean. Pre-dampen porous substrates to a surface-saturated dry condition; do not leave standing water. Mixing: Add powder to clean water while stirring until a smooth, lump-free, mortar-like consistency is reached. Mix only what you can place within the working time. Do not over-water. Placement for anchoring: Fill the prepared hole or pocket from the bottom up to avoid entrapped air. Insert the fixture or fastener while the mix is workable and align immediately. Hold steady until initial set. Placement for patching: Tightly pack the mix into the void in layers, compacting each layer to ensure full contact. Strike off and finish the surface as required. Curing: Protect from rapid drying, wind and direct sun during early cure. Avoid vibration or load until the material has hardened. Cleanup: Clean tools and splashes with water while product is fresh. Once hardened, mechanical removal may be required. Good practice tips Plan the job so placement occurs immediately after mixing for best expansion and bond. For deep holes or large voids, place in lifts and compact each lift. Do not confine completely in a sealed cavity; allow space for controlled expansion. Avoid adding sand, cement or other admixtures that can change performance. Performance and durability When correctly mixed and applied, Concremate develops a hard, dense matrix with strong adhesion to mineral substrates and embedded metals. The slight expansion on cure reduces micro-gapping at the interface, improving load transfer and long-term durability. After full cure at 28 days, the set material achieves hardness that exceeds standard concrete, supporting demanding anchoring and patching tasks. Safety and handling Wear suitable gloves, eye protection and a dust mask when mixing and placing. Avoid contact with skin and eyes. In case of contact, rinse with plenty of water. Store in a cool, dry place in the original, tightly closed container. Keep out of reach of children and pets. Specifications Product type Expanding cement anchoring and patching compound Form Premixed dry powder Color Grey Mix consistency Mortar-like paste when mixed with clean water Initial set About 30 minutes (conditions dependent) Hard set Approximately 1 hour (conditions dependent) Ultimate hardness Harder than standard concrete at 28 days Expansion Approx. 0.125% during cure Recommended substrates Concrete, brick, stone, tiles, plaster, terrazzo Primary uses Anchoring bolts, rails, brackets and fixtures; patching holes, chases and cracks; high-pressure grouting Cleanup Water while fresh Storage Cool, dry conditions in sealed container What to expect on the job With suitable surface preparation and correct mixing, you can expect a smooth placement, quick set and a dense, high-integrity bond. The expansion action helps lock hardware and patches into place. Protect new work from early movement and moisture loss, then return to service once the hard set has been achieved and the repair or anchorage has reached the necessary strength for your application. Limitations Not for use where the mix cannot expand slightly during cure. Do not apply over active movement joints or flexible substrates. Working and set times vary with temperature, humidity and mix ratio. Note: Always trial on a small, inconspicuous area or non-critical hole to confirm suitability for your specific substrate and conditions.
$17.00 - $99.00
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$9.70
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$28.21
Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS Initial set 5 minutes. Curing set 15-30 minutes. Compressive strength of 2,000psi or greater in 24 hours Maximum strength in 28 days Non-toxic Volume change: Expansion after 24 hours 0.1% Contraction after 28 days 0.01% Water absorption 1.7% after 14 days Factory Production to BS 5750 Part II BONDS TO: CEMENT TIMBER MASONRY FIBREGLASS STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.
$101.37
Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS Initial set 5 minutes. Curing set 15-30 minutes. Compressive strength of 2,000psi or greater in 24 hours Maximum strength in 28 days Non-toxic Volume change: Expansion after 24 hours 0.1% Contraction after 28 days 0.01% Water absorption 1.7% after 14 days Factory Production to BS 5750 Part II BONDS TO: CEMENT TIMBER MASONRY FIBREGLASS STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.
$145.00
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications. Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried. Environmentally friendly Dries white Dries fast Very high weather resistance Unique properties make this product easy to shape and sand Ideal for schools and craft classes or just having fun!
$39.15
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$24.50
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$9.33
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$167.00
Marathon Scale and Rust Remover CONCENTRATED 2L Bottle Tough on calcium, rust and scale deposits. Ideal to use on tiles, porcelain, sinks, showers and baths
$7.00
A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$29.36
Glitz Borax is a versatile cleaner and laundry booster that tackles grime, helps remove stains, and deodorises around the home. This mineral based powder dissolves in warm water to lift dirt, cut through residues, and freshen hard surfaces and fabrics. Why you will love it Multi purpose performance for laundry, kitchen, and bathroom Helps remove tough stains and lingering odours Boosts detergent effectiveness in hard water Deodorises bins, drains, and pet areas Free from added fragrance and chlorine Where to use Laundry booster for everyday washing Tiles, grout, sinks, and benchtops Toilets and bathroom surfaces Bins, outdoor furniture, and patios General deodorising tasks How to use Laundry booster: Add 1 to 2 tablespoons to the wash with your usual detergent. For heavily soiled loads use up to 1/4 cup. Dissolve in warm water for best results. Multi surface cleaner: Dissolve 2 tablespoons in 1 litre of warm water. Wipe surfaces with a cloth or sponge. Rinse food contact areas with clean water after cleaning. Stain pre soak: Dissolve 2 tablespoons in 2 litres of warm water. Soak colourfast fabrics for up to 30 minutes. Rinse well before washing as normal. Always patch test first. Deodorising paste: Mix borax with a little water to form a paste. Apply to tiles or grout, lightly scrub, then rinse. Bin and drain freshen: Sprinkle 2 to 3 tablespoons in the bin base or dissolve in warm water and flush down the drain. Rinse thoroughly. Good to know Use on sealed hard surfaces only Check fabric care labels and test on a hidden area first Not suitable for wool, silk, leather, or aluminium What is in the pack Glitz Borax powder 1 kg resealable pack Specifications Product type Multi purpose cleaner and laundry booster Form Free flowing powder Size 1 kg Fragrance None added Safety and storage Read and follow the label before use Wear gloves for prolonged contact Avoid inhaling dust. Use in a well ventilated area Keep out of reach of children and pets Do not ingest. Do not use on skin or as a personal care product Store in a cool dry place with the pouch sealed Disposal Rinse empty packaging and dispose of it in accordance with local council guidelines. Frequently asked questions Can I use it in cold waterYes, but it dissolves more readily in warm water. Pre dissolve in a small amount of warm water when using cold cycles. Is it safe for septic systemsUse sparingly and flush well with plenty of water. Follow any appliance and system guidelines. Will it bleach coloured fabricsIt does not contain chlorine bleach. Always check colourfastness and test on a hidden area first.
$12.22 $9.45
Give everyday cleaning a simple, natural boost with Glitz Bi-Carb Cleaner. This all purpose powder uses the gentle abrasive action and deodorising properties of sodium bicarbonate to lift grime, cut through kitchen film, and freshen household surfaces without added fragrances or dyes. Why you will love it Versatile cleaner for kitchens, bathrooms, laundry, and outdoor touch ups Deodorises fridges, bins, shoes, and pet areas Gentle abrasive action helps remove tea stains, soap scum, and cooked on residue Eco minded choice with a simple, trusted mineral based formula Food area friendly when used as directed, then rinsed well Value size 1kg pack is ideal for regular household cleaning Where to use Benchtops, sinks, stovetops, splashbacks Microwaves, fridges, lunch boxes, drinkware Showers, tiles, grout, basins Bins, pet bowls, outdoor furniture Laundry pre soak for odours in sportswear and towels Car interiors and coolers How to use General cleaning: Sprinkle a small amount onto a damp cloth or sponge. Wipe the surface, then rinse and dry. Stubborn marks: Make a paste with a little water. Apply to the stain, leave for 5 to 10 minutes, then scrub lightly and rinse. Deodorising: Sprinkle directly onto the source of odour, leave for 15 minutes, then vacuum or rinse away. Drains and sinks: Add half a cup followed by hot water to help freshen and reduce build up. Good to know Non scratch on most hard surfaces when used with a soft cloth No added fragrance or dyes Septic safe when used as directed Ingredients Sodium Bicarbonate. Care and safety Test on an inconspicuous area first, especially on delicate finishes and natural stone. Do not use on aluminium, lacquered or highly polished surfaces. Avoid contact with eyes. Keep out of reach of children and pets. Store tightly closed in a cool, dry place. Pack information Brand Glitz Product Bi-Carb Cleaner Natural Eco All Purpose Powder Net weight 1kg Format Fine cleaning powder Country of use Australia Simple tips Refresh chopping boards by applying a paste, scrubbing lightly, then rinsing with warm water. Neutralise fridge odours by placing an open dish in the fridge and replacing monthly. Lift tea and coffee stains in mugs by soaking with a warm water paste for 20 minutes before washing. What customers ask Is it safe on stainless steelYes, use a soft cloth, rub with the grain, then rinse and dry. Can it be used on natural stoneTest first. Rinse thoroughly and dry to protect sealed finishes.
$12.40 $10.11
Cut through stubborn limescale, soap scum, and rust stains with Glitz Calcium Scale and Rust Remover. This powerful bathroom cleaner is formulated to lift mineral build up fast so sinks, taps, tiles, glass, and shower screens look clean and fresh again. The generous 2L size is ideal for whole home maintenance or trade use. Why you will love it Targets tough mineral deposits like calcium, lime, and rust Breaks down soap scum for a brighter, streak free finish Works on ceramic, porcelain, glass, chrome, stainless steel, and most bathroom surfaces Fast acting formula helps reduce scrubbing time 2L value size for households, cleaners, and facilities teams Best for Shower screens and doors Wall tiles and grout surrounds Basins, baths, and toilets on the exterior porcelain Taps, shower heads, and chrome fittings Not recommended for Avoid natural stone like marble, limestone, travertine, or terrazzo. Avoid enamel cookware, unsealed or damaged surfaces, and any surface that states not to use acidic cleaners. If unsure, test on a small hidden area first. How to use Preparation Remove loose debris and pre rinse the surface with warm water. Light scale and soap scum Dilute 1 part product to 4 parts water. Apply with a sponge or spray bottle. Heavy scale and rust stains Use undiluted. Apply directly to the stain and let it sit for 2 to 5 minutes. Do not allow to dry on the surface. Agitate Wipe or scrub with a non scratch pad or soft brush. Rinse well Flush thoroughly with clean water until the surface is neutral and residue free. Repeat if needed For very stubborn deposits, repeat the process in short contact times. Pro tips For shower heads with internal scale, remove the head and soak in a diluted solution. Rinse well before refitting. Squeegee shower glass after each use to slow future build up. Always spot test first. Some finishes are more delicate than others. Safety and handling Wear gloves and eye protection during use Use in a well ventilated area and avoid inhaling mist Do not mix with bleach or ammonia Keep out of reach of children and pets Store upright in a cool, dry place with cap closed After care Once deposits are removed, maintain surfaces with a neutral pH daily cleaner. Regular rinsing and drying will help prevent new mineral build up. Product details Brand Glitz Product Calcium Scale and Rust Remover Bathroom Deep Clean Size 2L Form Liquid Suitable surfaces Ceramic, porcelain, glass, chrome, stainless steel, most glazed tiles Do not use on Natural stone, terrazzo, unsealed or damaged surfaces, acid sensitive finishes Cleanup Rinse with plenty of clean water What is in the box 1 x Glitz Calcium Scale and Rust Remover 2L Good to know Contact time should be short. Rinse thoroughly to protect finishes. For vertical surfaces, apply with a sponge to reduce run off. For regular maintenance, switch to a gentle daily cleaner between deep cleans.
$23.66 $20.12
Glitz Spray On Wipe Off Everyday Surface Cleaner 750ml Glitz Spray On Wipe Off is your quick daily cleaner for busy kitchens, bathrooms, and high touch areas. Just spray, wipe, and you are done. It cuts through everyday grease, food splatter, soap scum, and dust to leave surfaces fresh and streak free. Why you will love it Fast spray and wipe action for daily clean ups Lifts light grease, grime, and sticky residues Streak free finish on most hard household surfaces Fresh clean scent that does not linger Ready to use 750ml trigger bottle for easy coverage Ideal for Benchtops and splashbacks Stainless steel appliances and rangehood exteriors Cooktops when cool, microwaves, fridges, and pantry shelves Bathroom vanities, taps, tiles, and shower glass Tables, desks, cabinet doors, light switches, and door handles Not recommended for Unsealed or waxed surfaces Natural stone such as marble, limestone, or travertine Untreated wood, leather, or fabrics Plasma or non glass coated display screens How to use Turn nozzle to the ON position. Spray directly onto the surface from about 20 cm away. Wipe with a clean damp cloth or paper towel. For stuck on grime, leave for 30 to 60 seconds before wiping. Buff with a dry cloth for a clear finish. Return nozzle to OFF after use. Pro tips Always test on an inconspicuous spot first. For food preparation areas, wipe with a clean damp cloth after cleaning. Use a microfiber cloth for best streak control on glass and stainless steel. Product details Brand Glitz Product type Everyday spray cleaner Format Ready to use Fragrance Fresh clean Bottle size 750 ml Surface compatibility Most sealed hard surfaces including laminate, ceramic, porcelain, stainless steel, glass, and finished wood What is in the box 1 x Glitz Spray On Wipe Off Everyday Surface Cleaner 750ml with trigger Storage and safety Store upright in a cool, dry place away from direct sunlight. Keep out of reach of children and pets. Avoid contact with eyes. If contact occurs, rinse with water. Do not mix with other chemicals. FAQs Can I use it on stone benchtops Use only on sealed engineered stone. For natural stone like marble or limestone, use a stone specific cleaner. Does it leave residue It is designed to wipe clean. For food areas, finish with a damp cloth to remove any remaining cleaner. Is it suitable for glass Yes for quick touch ups. For crystal clear windows, follow with a dry microfiber buff. Good to know Great for daily resets after cooking and bath time Trigger head lets you choose between stream and spray patterns Pairs well with microfiber cloths and paper towels
$33.11 $26.17
Glitz Sugar Soap for Floors Heavy Duty Cleaner Power through ground-in dirt, grease, and everyday grime with Glitz Sugar Soap for Floors. This heavy duty formula lifts stubborn residues and leaves floors fresh, streak free, and ready for living. Ideal for high traffic areas in homes, workshops, and commercial spaces. Why you will love it Heavy duty clean that cuts through grease, scuff marks, and sticky spills Low foam for a streak free finish on most sealed floors Fast acting formula reduces scrubbing time Residue free so finishes and sealers look their best Fresh, low odour for comfortable indoor use Best for these surfaces Use on most sealed and washable floors, including: Ceramic and porcelain tiles Vinyl and hybrid floors Laminate and sealed timber Sealed concrete and epoxy coated floors Do not use on unsealed timber, unsealed cork, natural stone that is unsealed, or waxed finishes. Always test in a small inconspicuous area first. How to use Sweep or vacuum to remove dust and grit. Dilute in warm water: General cleaning: 1 capful per 5 L bucket Heavy duty cleaning: 2 to 3 capfuls per 5 L bucket Apply with a mop or sponge. Work in sections. For stubborn spots, apply a little solution directly, wait 2 to 3 minutes, then gently agitate. Rinse mop frequently in clean water. Allow floor to dry before walking. Pro tips Change the bucket water when it turns cloudy to avoid streaks. Use heavy duty dilution before repainting or resealing floors to remove grease and prep the surface. For gloss finishes, wring the mop well to prevent pooling. Product details Brand Glitz Product type Sugar soap floor cleaner Format Liquid concentrate Appearance Clear to light solution, low foam Suitable surfaces Most sealed hard floors Clean up Rinse tools and mops in clean water Storage Keep tightly closed in a cool, dry place Safety Wear gloves if you have sensitive skin. Avoid contact with eyes. If splashed, rinse with water. Keep out of reach of children and pets. FAQs Do I need to rinse after cleaning Rinsing is generally not required on sealed floors when diluted as directed. If using heavy duty strength, a light rinse with clean water can help achieve a streak free finish. Can I use it in a spray mop Yes. Pre dilute following the general cleaning ratio and avoid over wetting the floor. Good to know Compatible with most microfiber and cotton mops Great prep step before resealing or repainting floors Helps remove oily residues that make floors feel slippery
$5.27 $4.94
Glitz Domestic Cleaner Multi Purpose Surface Shine 1.25L is your everyday helper for a fast, streak free clean. Spray, wipe, and enjoy a bright finish on benches, tables, appliances, and other sealed surfaces around the home. Why you will love it Cuts through daily grime and light grease with ease Leaves a streak free shine on most sealed surfaces Fresh, clean household scent that does not linger No rinsing required on lightly soiled areas Ready to use for quick jobs or dilute for larger areas to save cost Best for Kitchen benches, tables, cupboards, splashbacks Bathroom vanities, tiles, taps, glass shower screens outside surface only Door handles, light switches, appliances exterior, bins Floors when diluted in a bucket for general freshen ups Do not use on Unsealed or waxed timber Natural stone that is unsealed or acid sensitive such as marble and limestone Screen displays or electronics Delicate finishes. Always spot test in a hidden area first How to use Light cleaning. Spray directly onto the surface and wipe with a clean cloth Heavier soil. Let sit for 30 to 60 seconds then wipe. Repeat if required Floors. Add 60 to 100 ml per 5 L of warm water, mop, then allow to dry Glass and glossy areas. Use a lint free cloth and buff dry for best results Quick tips Use separate cloths for kitchen and bathroom to avoid cross contamination For stainless steel, always wipe with the grain and finish with a dry cloth On painted surfaces, apply to cloth first, not directly to the wall Specifications Brand Glitz Product Domestic Cleaner Multi Purpose Surface Shine Format Ready to use liquid. Dilutable for floors Pack size 1.25 L bottle Fragrance Fresh household scent Surface compatibility Most sealed hard surfaces including laminates, sealed stone, ceramic tile, porcelain, stainless steel, enamel, and sealed timber Country of use Suitable for Australian homes and water conditions What is in the box 1 x Glitz Domestic Cleaner Multi Purpose Surface Shine 1.25 L Storage and safety Store upright in a cool, dry place away from direct sunlight Keep out of reach of children and pets Avoid contact with eyes. If in eyes rinse with water Do not ingest. If swallowed seek medical advice Frequently asked questions Can I use it on food contact areas Yes. Clean the surface, then wipe with a damp cloth and allow to dry before food preparation Will it leave residue No when used as directed. Buff with a dry cloth on glass or glossy areas for a crystal finish Is rinsing required Not for light soil. For heavy soil or floors, rinse the mop head regularly for best results Good to know Ideal for quick daily resets in kitchens and bathrooms Economical size that suits family households and shared spaces
$6.51 $6.04
Glitz Citrus Dishwashing Liquid Fresh Lemon Clean 5L Make light work of dishes with a refreshing lemon clean. Glitz Citrus Dishwashing Liquid delivers rich suds that lift grease and food residues fast, leaving plates, glasses, and cookware spotless with a fresh citrus finish. The generous 5L bulk pack is ideal for busy family homes, offices, cafes, and community kitchens that want reliable performance and great value. Why you will love it Powerful everyday clean that breaks down oils and baked on residues Fresh lemon fragrance for a just cleaned scent Stable foam for longer sink time and fewer top ups Rinses easily to help reduce spotting and streaks Cost effective 5L format for regular high volume washing Versatile for hand washing dishes, cutlery, glassware, and cookware Best for Daily sink loads at home or in shared kitchens Cafes, lunchrooms, clubs, and community events Rental properties and short stay turnovers How to use Fill sink with warm water. Add dishwashing liquid. Start with 1 to 2 teaspoons per 5L of water for light to normal soils. Increase for heavy grease. Wash using a sponge or brush. Soak stubborn items for a few minutes. Rinse thoroughly with clean water and allow to air dry or towel dry. Tips For glassware, use hot water and a soft sponge to help prevent water spots. Change solution when suds begin to collapse or water appears cloudy. Do not use in automatic dishwashers. This formula is for manual washing. Product details Brand Glitz Product Citrus Dishwashing Liquid Fragrance Fresh Lemon Format Liquid Size 5L Use Manual dishwashing and general sink cleaning Suitable surfaces Dishes, cutlery, glassware, ceramics, stainless steel cookware Country of use Australia What is in the box 1 x Glitz Citrus Dishwashing Liquid Fresh Lemon Clean 5L Storage and safety Store upright in a cool, dry place away from direct sunlight. Keep out of reach of children and pets. Avoid contact with eyes. If product gets in eyes rinse with water. If irritation occurs discontinue use. Sustainability note Use the recommended dose to minimise waste and water use. Recycle the container where local facilities allow. Frequently asked Can I use it on non stick cookware Yes, use a soft sponge and follow the cookware care instructions. Is it safe for septic systems This hand dishwashing liquid is designed for general household use. As with any cleaner, use as directed and follow local guidance for septic systems.
$25.86 $20.56
Glitz Pine Disinfectant Commercial Grade Sanitiser 5L Refresh and sanitise high traffic areas with the classic clean of pine. Glitz Pine Disinfectant is a commercial grade cleaner that cuts through everyday grime, removes unpleasant odours, and leaves a crisp pine aroma. Ideal for homes, workplaces, schools, gyms, and hospitality areas where a fast, reliable clean is needed. Why you will love it Commercial grade performance for large and small areas Deodorises while it cleans with a fresh pine scent Versatile on sealed floors, benches, walls, bathrooms, and bins Low effort mop and wipe application Economical 5L size suited to frequent use and refill stations Where it works Sealed hard floors including tiles, vinyl, sealed concrete, and sealed timber Bathrooms, toilets, showers, and change rooms Kitchen and lunchroom benches, splashbacks, and cupboards Door handles, railings, desks, and other high touch points Bins and pet areas surfaces only, avoid direct contact with food How to use Always test on a small inconspicuous area first. Do not use on unsealed or porous stone. Avoid prolonged contact with natural marble and other acid sensitive surfaces. Application Dilution guide Directions General mopping and daily clean 1:80 to 1:100 (50 to 100 mL per 8 L bucket) Add to warm water, mop the surface, then allow to air dry. No rinse required on lightly soiled, non food contact areas. Bathrooms and heavy soil 1:10 to 1:20 Apply with sponge or cloth, scrub if needed, allow contact for 5 minutes, then rinse with clean water. Spray and wipe 1:20 in a trigger bottle Spray onto surface, wipe with a clean microfibre cloth, and let dry. Rinse food contact surfaces with potable water. Deodorising bins and drains Neat or 1:5 Rinse the area first, apply, allow contact time, then rinse away. Pro tips Use separate colour coded cloths and mops for bathrooms and kitchens to reduce cross contamination. For streak free floors, wring the mop well and change the solution when it becomes visibly dirty. Store the concentrate upright with the cap sealed to preserve freshness. Product details Brand Glitz Product type Pine disinfectant and sanitising cleaner Fragrance Pine Form Liquid concentrate Container size 5 litres Suitable surfaces Sealed hard floors, tiles, vinyl, sealed concrete, bathrooms, benches, walls Do not use on Unsealed stone, natural marble, unfinished timber, fabrics, or screens Safety and handling Read label before use. Keep out of reach of children. Use in well ventilated areas. Avoid breathing spray. Wear gloves if you have sensitive skin or prolonged contact is expected. Avoid contact with eyes. If in eyes, rinse with water for several minutes. Do not ingest. If swallowed, seek medical advice. Store in a cool, dry place away from direct sunlight. Frequently asked questions Can I use this on food contact surfaces Yes, but after cleaning you must rinse those surfaces with potable water. Will it leave a sticky residue When used at the recommended dilutions and allowed to dry, it leaves a fresh, clean finish without tackiness. Is it pet friendly Allow surfaces to dry completely before pets return. Do not allow pets to ingest the solution. Good to pair with Microfibre cloths for streak free wipe downs Colour coded mop heads and buckets for hygiene zones Trigger spray bottles for quick touch up cleans
$27.62 $20.89
Glitz Caustic Soda for Drains and Heavy Duty Cleaning 500g Cut through the toughest grime with Glitz Caustic Soda. These high strength crystals are ideal for clearing slow or blocked drains and tackling heavy duty cleaning tasks in workshops, garages, and outdoor areas. Designed for fast action on built up fats, oils, soap scum, and organic matter, it is a must have for serious cleaning jobs. Key benefits Unblocks and deodorises kitchen, bathroom, and laundry drains Heavy duty degreasing power for floors, bins, and exterior concrete Crystalline form for controlled use and minimal waste Effective on fats, oils, grease, and soap build up Convenient 500 g jar suitable for home and trade users Where it works Kitchen sinks and traps Bathroom basins, showers, and laundry tubs Outdoor drains and gullies Greasy hard surfaces like concrete and pavers What to know before you start Always wear chemical resistant gloves, eye protection, and long sleeves Use in a well ventilated area and avoid breathing dust Do not mix with acids, bleach, or other chemicals Add crystals to water, never water to crystals Not suitable for aluminium, zinc, tin, or painted and delicate surfaces How to use Remove as much standing water and debris as possible from the drain or surface. Carefully dissolve the required amount of crystals in cold water. Stir gently until dissolved. Pour the solution slowly into the drain or apply to the surface. Avoid splashing. Allow time to work, then flush drains thoroughly with plenty of water or rinse surfaces well. Repeat if necessary for heavy build up, following all safety directions. Good practice tips For maintenance, treat problem drains periodically to prevent build up Keep children and pets away from the work area until rinsed and dry Store tightly closed in a cool, dry place away from moisture Product details Brand Glitz Product Caustic Soda Chemistry Sodium hydroxide Form Crystals Size 500 g Suitable for Drains, heavy duty degreasing on hard, non reactive surfaces Not for use on Aluminium, zinc, tin, painted surfaces, natural stone, fiberglass, anodised finishes Safety and first aid Corrosive. Avoid contact with skin and eyes. Do not ingest. In case of contact, flush with water for at least 15 minutes and remove contaminated clothing. If swallowed or eye exposure occurs, seek medical advice immediately. In Australia contact the Poisons Information Centre on 13 11 26. Frequently asked questions Will it damage my pipes Glitz Caustic Soda is suitable for most household drains when used as directed. Avoid use on systems with aluminium components and always flush thoroughly. Is it safe for septic systems Generally suitable when used as directed and in moderation. Avoid repeated heavy dosing. If unsure, consult a licensed plumber. Can I use it on painted or decorative surfaces No. It can strip or dull finishes. Use only on compatible, non reactive hard surfaces. You may also need Heavy duty chemical resistant gloves Protective eyewear Plastic drain auger for physical blockage removal Always follow the directions on the packaging. Test on a small, inconspicuous area for surface compatibility.
$6.16 $4.83
Dunlop Trade Resaflex Rapidset Tile Adhesive 15kg is a high quality, fast setting, rubber modified cement-based adhesive designed for rapid installation and early grouting. It delivers strong adhesion on walls and floors and is suitable for interior applications and exterior areas with satisfactory drainage. Key benefits Ready to grout in about 3 hours at 23°C and 50% RH Rubber modified formulation for strong bond and improved workability Classified C1FES1 Suitable bed thickness from 1.5 mm up to 10 mm Wall and floor use, interior and exterior (with correct falls and drainage) Suitable tiles Ceramic, porcelain, vitrified and mosaics Non moisture sensitive stone Suitable substrates Render, plasterboard, fibre cement sheet walls Compressed fibre cement sheet floors, concrete floors Existing tiles for interior applications Mixing and use Water addition: 5.5 L to 6.0 L per 15 kg bag Pot life: about 40 minutes at 23°C and 50% RH Trowel guidance: 6 x 6 x 6 mm on walls to achieve about 1.5 mm bed. 10 x 10 x 10 mm on floors to achieve about 2.5 mm bed Back buttering recommended for deeply keyed tiles and tiles larger than 450 mm on any edge Grouting: typically after about 3 hours at 23°C and 50% RH Coverage guide Trowel size Approximate coverage 6 mm About 0.6 m² per kg (about 9 m² per 15 kg) 10 mm About 0.4 m² per kg (about 6 m² per 15 kg) Movement joints Include movement joints in line with AS 3958 and around perimeters, penetrations and changes in direction. Fill with a suitable flexible sealant. Clean up Clean tools and residue with water while the adhesive is wet. Limitations Not suitable for continuous immersion such as swimming pools Not for moisture sensitive or translucent stone Do not tile directly over timber floors Safety Wear gloves, eye and face protection. Avoid breathing dust. In case of contact with eyes, rinse with water and seek medical advice. Keep out of reach of children. Technical details are based on manufacturer guidance at standard conditions. Actual times and coverage vary with temperature, humidity, tile and substrate.
$56.95
Selleys Araldite Extra Time Epoxy Adhesive 200ml Araldite Extra Time is a strong two part epoxy that gives you an extended working time of up to 60 minutes. It is ideal for complex or multi piece assemblies where accurate positioning matters. Once cured it forms a tough, durable bond that dries translucent. Why you will love it Extended working time of 60 minutes for precise assembly Holds up to 150 kg per cm² when fully cured on clean, abraded steel Dries translucent for a neat finish Versatile bonding across common materials Suitable materials Wood, metal, masonry, china, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. Pre test on leather and rubber for suitability. Typical uses Furniture repairs and assemblies Fixing metal or timber components General household, hobby, and craft bonding Repairs on masonry, ceramics, and glass where a clear finish is preferred Directions Surface prep: abrade, clean, and dry both surfaces. Pierce each tube using the spike in the cap. Dispense equal parts onto a clean disposable surface. Mix thoroughly. Leave for 5 minutes, then mix again before applying. Mixed glue is usable for about 1 hour at 20°C. Do not use the plastic blister to mix. Apply to both surfaces and join. Support if needed to prevent movement. Avoid strain for 6 to 8 hours. Full strength develops after 24 to 72 hours depending on conditions. Replace caps on the correct tubes to avoid cross contamination. Clean up Wipe away uncured adhesive with acetone. Once cured, mechanical removal is required. Key specs Technology Two part epoxy Working time Up to 60 minutes Initial handling 6 to 8 hours Full cure 24 to 72 hours Bond strength Up to 150 kg per cm² on abraded steel when fully cured Appearance Dries translucent Temperature resistance Up to 80°C. Bond may soften above this but strength returns when temperature normalises. Pack size 200 ml Good to know Allow longer bonding times in colder weather. Product may discolor with UV exposure. Store in a cool dry place.
$66.48
Davco Ceramacrete Cement Base Tile Adhesive 5kg Davco Ceramacrete is a cement based tile adhesive for rigid substrates with patented Dust Less technology that reduces airborne dust during mixing. It offers good bond strength, tidy mixing and clean up, and can be used in thin or thick beds for efficient tiling results. Where to Use Interior and exterior walls and floors Bathrooms, showers, kitchens, laundries, living areas, balconies and patios Domestic and light duty commercial projects Tile Types Ceramic Mosaic Terracotta Slate Quarry tiles Not suitable for natural stone. Suitable Substrates Concrete Cement based screeds and renders Rendered block or brickwork For flexible framed substrates or submerged applications such as pools and spas, use with Davco Davelastic additive as directed. Key Features Dust Less formula for less mess and faster clean up Good bond strength Usable for thin bed and thick bed tiling Colour varies from white to grey Low VOC 5 g/L Mixing and Application Mixing ratio 1.25 L of clean cool water per 5 kg bag Allow to stand for 5 minutes after mixing, then remix before use Do not add extra water after initial mixing Working Times at 23°C and 50% RH Pot life 40 minutes Open time 7 minutes Adjustability time 15 minutes Ready for Use Grouting after 24 hours Return to dry area service after 24 hours Return to wet area service after 7 days Preparation Tips Ensure substrates are sound, clean, dry and free from contaminants Prime as required according to substrate condition and primer directions Install movement joints in line with good tiling practice Clean Up and Safety Clean tools with water before the adhesive dries Use appropriate personal protective equipment Refer to the product SDS for detailed safety advice
$10.30
Dunlop Trade Resaflex Rapidset Tile Adhesive 5 kg Overview Dunlop Trade Resaflex Rapidset Tile Adhesive 5 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$23.94
Dunlop Mastic Multipurpose Tile Adhesive High performance, cementitious, non-slump tile adhesive designed for walls and floors. Combines the ease of a mastic with the strength of a cement-based adhesive for reliable results on small to large format tiles. Why choose it Non-slump hold for heavy and large format tiles Indoor and outdoor use on approved substrates Extended open time of up to 30 minutes to position tiles Bed thickness up to 10 mm White colour for use under light or translucent tiles Classification: C2TES1 Suitable tiles Ceramic, porcelain, mosaics, natural stone that is not moisture sensitive, fully vitrified and translucent tiles. Suitable substrates Render, screeds, concrete Plasterboard, fibre cement sheet walls, compressed fibre cement sheet floors Ceramic tile underlay Existing ceramic tiles indoors (properly prepared) Dunlop undertile waterproofing membranes Where it excels Walls needing strong initial grab Floors requiring reliable coverage and non-slump Large format and deeply keyed tiles where full contact is critical Coverage guide 6 mm notch (walls): about 0.5 m² per kg 10 mm notch (floors): about 0.3 m² per kg 5 kg bag: up to ~2 m² on walls or ~1.2 m² on floors 20 kg bag: up to ~10 m² on walls or ~6 m² on floors Set and grout times Allow approximately 24 hours at 23°C and 50% RH before grouting and light foot traffic. Dense tiles, cool weather or humid conditions may extend set time. Mixing 20 kg bag: 6 to 6.5 L of clean water 5 kg bag: 1.5 to 1.75 L of clean water Mix to a creamy consistency, stand for 5 minutes, then re-mix before use Application tips Follow AS 3958 best practice Spread only as much adhesive as can be tiled within the open time Press and slide tiles at right angles to the notches to achieve full contact Back-butter large or deeply keyed tiles for 100% coverage Remove squeeze-out from joints before setting Not suitable for Moisture sensitive natural stone Areas under permanent water immersion such as pools Timber, metal or any substrates subject to movement Application below 5°C Sizes 5 kg and 20 kg bags. Clean up Clean tools with water immediately after use. Safety Wear gloves and eye protection. Avoid inhaling dust. Refer to the product SDS and follow all safety directions.
$21.05
Selleys Araldite Rapid Epoxy Adhesive 14 mL Fast-setting, two-part epoxy for quick, durable repairs at home, in the workshop, or on site. The self-mixing syringe makes application clean and precise, setting in about 90 seconds and reaching handling strength soon after. Dries translucent for a neat finish. Key benefits Sets in approximately 90 seconds for rapid fixes High strength bond up to 75 kg/cm² when fully cured Dries translucent for low-visibility repairs Self-mixing nozzle for easy, accurate application Versatile bonding across common materials Best for Everyday repairs and small assemblies Fixing chipped ceramics and china Metal, glass, leather, rubber, and many plastics Suitable materials China, metal, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. How to use Prep Abrade, clean, and dry both surfaces. Attach nozzle Remove cap, fit and lock the self-mixing nozzle, then purge a small amount until evenly mixed. Apply Spread adhesive on both surfaces and join within 1 minute. Hold Support the bond for about 10 minutes to prevent movement. Cure Maximum strength develops after about 16 hours. Allow longer in cold conditions. Clean up Wipe away uncured adhesive with acetone. Remove and dispose of the used mixing nozzle before the adhesive sets in the tip. Technical details Technology Two-part epoxy Set time About 90 seconds Handling time Approximately 10 minutes Full cure About 16 hours Colour when dry Translucent Temperature resistance Up to 60 °C Pack size 14 mL self-mixing syringe Good to know Bond may soften above 60 °C and regains strength when cooled. Pre-test on leather and rubber to confirm suitability. May discolor with prolonged UV exposure. Store in a cool, dry place. Replace cap after removing the used nozzle. Safety Follow the safety directions on the packaging. Use in a well-ventilated area and avoid skin contact. Keep out of reach of children.
$16.89
Dunlop Trade Resaflex Tile Adhesive 5 kg Overview Dunlop Trade Resaflex Tile Adhesive 5 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$23.25
Davco Davelastic Tile Adhesive Additive 1 L is a reliable latex additive to upgrade cement based tile adhesive performance chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 1 L pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Davco Davelastic for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Davco Davelastic Tile Adhesive Additive 1 L has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Improving bond strength and flexibility Situations where extra deformability is required Wet area tiling as part of a system Suitable surfaces The adhesive works well on the following surface types when properly prepared: Concrete, screeds, and renders Cement based adhesives and grouts as specified Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of follows the base adhesive behaviour. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Replace all or part of the mixing water with the additive as directed. Observe normal set and cure times for the base adhesive. Temperature and environmental performance Use within the recommended application window of the system you are modifying. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wash tools with water while the mix is fresh. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed. Protect from freezing. Shake before use. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$27.84
Davco SMP Evo Flexible Tile Adhesive 5 kg is a reliable polymer modified flexible tile adhesive for demanding substrates chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 5 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Davco SMP for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Davco SMP Evo Flexible Tile Adhesive 5 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bathrooms, kitchens, and balconies Tiling over existing tiles where movement accommodation is needed Floor and wall applications Suitable surfaces The adhesive works well on the following surface types when properly prepared: Concrete and screeds Fibre cement sheeting Existing glazed tiles after scuffing and cleaning Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of per data on the bag, adjust for weather. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Observe open time, bed thickness, and traffic restrictions. The polymer modification gives improved flexibility once cured. Temperature and environmental performance Install in moderate conditions and shield fresh work from wind and direct sun. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Water clean-up while fresh. Remove haze before it hardens. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep the bag closed and dry between uses. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$26.38
Dunlop Floorfix Professional Tile Adhesive 15 kg is a reliable cement based floor tile adhesive for porcelain and ceramic tiles chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 15 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Dunlop Floorfix for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Dunlop Floorfix Professional Tile Adhesive 15 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for General floor tiling High traffic residential areas Back buttering dense porcelain tiles Suitable surfaces The adhesive works well on the following surface types when properly prepared: Concrete slabs and screeds Cement sheet underlay Existing tiles that are clean and sound Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of as indicated on the bag for best wetting and transfer. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Respect open time and bed thickness. Allow adequate set before grouting and opening to traffic. Temperature and environmental performance Apply in suitable ambient conditions for predictable cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Damp sponge on fresh residue, water clean-up for tools. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store sealed and dry to prevent lumping. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$18.53
Dunlop AAC Block Construction Adhesive 15 kg is a reliable thin bed adhesive for autoclaved aerated concrete blockwork chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 15 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Dunlop AAC for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Dunlop AAC Block Construction Adhesive 15 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Laying AAC blocks in internal and external walls Creating straight and plumb courses with minimal waste Suitable surfaces The adhesive works well on the following surface types when properly prepared: AAC blocks and panels Suitable primed substrates as per system design Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of follow bag guidance for open time and pot life. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Mix to a creamy consistency and apply with a notched trowel. Align blocks within the open time and tap to level. Allow to set before further work. Temperature and environmental performance Protect fresh work from rain, frost, and high heat. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wash tools with water while material is fresh. Remove spills promptly. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep dry and use within shelf life. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$32.41
Bastion Superlite Lightweight Tile Adhesive 11 kg is a reliable lightweight polymer modified tile adhesive with excellent spread chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 11 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Bastion Superlite for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Bastion Superlite Lightweight Tile Adhesive 11 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Large format wall and floor tiles Substrates where reduced slump is beneficial Renovations that require easy trowelling Suitable surfaces The adhesive works well on the following surface types when properly prepared: Concrete and screeds Fibre cement sheet Existing tiles suitably prepared Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of per data on the bag for open time and adjust for ambient conditions. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Observe recommended open time and bed thickness. Allow the adhesive to set before grouting and traffic. Temperature and environmental performance Install in mild weather to ensure predictable curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean trowels and buckets with water before the mix hardens. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store the bag sealed in a dry place off the ground. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$41.95
Protite Mould Defender Anti-Fungal Paint Additive 75 mL is a reliable liquid paint additive that helps inhibit mould growth in humid areas chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 75 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Protite Mould for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Protite Mould Defender Anti-Fungal Paint Additive 75 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bathrooms and laundries Kitchens and food prep zones Rental refresh and maintenance work Suitable surfaces The adhesive works well on the following surface types when properly prepared: Walls and ceilings coated with water based paint Suitable primers as per paint maker guidance Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of Work to normal paint tray timelines. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Mix thoroughly into your chosen paint and apply as directed by that paint. Dry and recoat times follow the paint system. Temperature and environmental performance Use within the temperature window recommended for the host paint. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean rollers and brushes according to the paint manufacturer's advice. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store upright with cap tight. Do not allow to freeze or overheat. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$27.64
Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL is a reliable two part fast setting epoxy adhesive for durable repairs chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 24 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Tarzan's Grip Grip for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Household and workshop repairs that need speed and strength Fixing fixtures, brackets, and hardware Filling chips and rebuilding small edges before sanding Suitable surfaces The adhesive works well on the following surface types when properly prepared: Metal hardware Ceramic tiles Most rigid plastics except polyethylene and polypropylene Timber and MDF Stone and concrete Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of 3 to 5 minutes working time. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Initial set is reached in about 5 minutes at 23 C. Sandable after several hours. Achieves high final strength after a full overnight cure. Temperature and environmental performance Performs well across typical domestic temperature ranges after cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured excess with acetone on a cloth. Use care on painted substrates. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed to prevent crystallisation. Store upright at moderate temperature. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$11.50
Casting, modelling, moulding, sculpting, carving. Fine quality to hold detail. Sands smooth.
$16.64
Casting, modelling, moulding, sculpting, carving. Fine quality to hold detail. Sands smooth.
$8.50
Ultra high-strength 2-component epoxy adhesive for the heaviest loads (up to 1700 N/cm²). Working time: 90 minutes, handling strength: 6 hours, final bond: 24 hours. Can be drilled, sanded and painted. Resistant to impact, ageing, dampness, heat and cold. Suitable for metal, stone, concrete, marble, china, wood, glass, duro-plastics, glass-fibre reinforced plastics, rigid PVC and Styrofoam.* Not suitable for PE, PP, PS, soft PVC. UHU Epoxy Quick Set High-performance 2-component epoxy adhesive for quick and reliable repairs. Dries clear. Working time: 5 minutes, handling strength: 20 minutes, final bond: 12 hours. Resistant to impact, ageing, dampness, heat and cold.
$8.57
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$18.48
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, benchtops, tiles, slate, stainless steel, baths, glass, stovetops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQs. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra-concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$5.33
Single Use Waterproof Epoxy Adhesive is the perfect product to use when you need to do any marine or waterproof projects. It works under or in the presence of water and remains waterproof. Package contains just the right amount of product for most small projects. The metal tubes dispense effortlessly and are easy to mix. This product sets in only 3-4 hours.
$29.00
Quick Setting Single Use Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 5 minutes. Works best on: All-Purpose Ceramic Metal Pottery Wood Tile Crafts Fabric Properties: Initial colour: Clear hazy to light yellow Final colour: Light yellow Set Time: 4-6 minutes @ 65-80F Handling Time: After 30 minutes Full Strength: 24 hours Maximum Gap:25" Hardness, Shore D: 75-83 (After full cure) Shear Strength, Steel: 1200 psi ( 20%) Operating Temperature Range: -40o F to +176oF (-40oC to +80oC) Instructions: 1. Surfaces should be clean and dry, free of oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from containers following package directions and mix thoroughly approximately 1 minute. 4. Apply mixed epoxy to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours. Storage: After use, wipe tips to remove residual product and reseal the container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains Epoxy resin & Mercaptan hardener. May cause eye/skin irritation with direct contact. In case of direct eye contact, flush with water for 15 minutes and consult a physician. Wash hands and skin thoroughly with soap and water after use. If swallowed, seek medical advice immediately and show container label. Keep out of reach of children.
$29.95
Instant Setting Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 90 seconds Pacer Technology Super Glue 90 Second Instant Epoxy Adhesive (SY-IN, 15353) works best on: • All Purpose • Ceramic • Glass • Wood • Leather • Fiberglass • Metals • Most Plastics Properties: Initial color: Clear to amber Mix Ratio (parts by volume): 1:1 Final color: Light yellow Maximum Gap: .25” Set Time: 90 Seconds @ 65-80F Hardness, Shore D: 75-85 (After full cure) Handling Time: After 10 minutes Shear Strength, Steel: 2000 psi (± 20%) Full Strength: 24 hours Operating Temperature Range:-400 to 1400F (-400 to 600C) Use: 1. Surfaces should be clean and dry, free from oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from container following package directions and mix thoroughly until color is uniform. 4. Apply to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 90 seconds at room temperature (77F or 25C) with full cure in 24 hours. STORAGE AND SHELF LIFE After use, wipe tips to remove residual product and reseal container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected.
$25.00
Quick Setting Single Use Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 5 minutes. Pacer Technology Super Glue Quick Setting Epoxy (SY-QS, SYQS8, T-QS, 15250, 15350) works best on: All-Purpose Ceramic Metal Pottery Wood Tile Crafts Fabric Properties: Initial colour: Clear hazy to light yellow Final colour: Light yellow Set Time: 4-6 minutes @ 65-80F Handling Time: After 30 minutes Full Strength: 24 hours Maximum Gap:25" Hardness, Shore D: 75-83 (After full cure) Shear Strength, Steel: 1200 psi ( 20%) Operating Temperature Range: -40oF to +176oF (-40oC to +80oC) Use: 1. Surfaces should be clean and dry, free of oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from containers following package directions and mix thoroughly approximately 1 minute. 4. Apply mixed epoxy to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours.
$19.95
Single Use Quick Setting Metal Epoxy Adhesive is perfect for repairing appliances, tools, etc. It bonds most metals including copper, steel, stainless steel, aluminum, brass and iron. Package contains just the right amount of product for most small projects. The metal tubes dispense effortlessly, and are easy to mix. This product sets in only 5 minutes and the final cure color is light gray. Works best on: Aluminum Brass Copper Iron Stainless Steel Steel Properties: Initial colour: Light grey Maximum Gap: .25” Final colour: Hazy-clear Hardness, Shore D: 75-85 (After full cure) Set Time: 4-6 minutes @ 65-80F Shear Strength, Steel: 2500 psi (± 20%) Handling Time: After 1-hour Aluminum: 840 psi (± 20%) Full Strength: 24 hours Operating Temperature Range:-400 to 3000F (-400 to 1490C) Use: 1. Surfaces should be clean and dry, free of oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from container following package directions & mix thoroughly until colour is uniform, approximately 1 minute. 4. Apply to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours. Storage: After use wipe tips to remove residual product and reseal the container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains Epoxy resin & Mercaptan hardener. May cause eye/skin irritation with direct contact. In case of direct eye contact, flush with water for 15 minutes and consult a physician. Wash hands and skin thoroughly with soap and water after use. If swallowed, seek medical advice immediately and show container label. Keep out of reach of children.
$17.00
Single Use Quick Setting Metal Epoxy Adhesive is perfect for repairing appliances, tools, etc. It bonds most metals including copper, steel, stainless steel, aluminum, brass and iron. Package contains just the right amount of product for most small projects. The metal tubes dispense effortlessly, and are easy to mix. This product sets in only 5 minutes and the final cure color is light gray. Works best on: Aluminum Brass Copper Iron Stainless Steel Steel Properties: Initial colour: Light grey Maximum Gap: .25” Final colour: Hazy-clear Hardness, Shore D: 75-85 (After full cure) Set Time: 4-6 minutes @ 65-80F Shear Strength, Steel: 2500 psi (± 20%) Handling Time: After 1-hour Aluminum: 840 psi (± 20%) Full Strength: 24 hours Operating Temperature Range:-400 to 3000F (-400 to 1490C) Use: 1. Surfaces should be clean and dry, free of oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from container following package directions & mix thoroughly until colour is uniform, approximately 1 minute. 4. Apply to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours. Storage: After use wipe tips to remove residual product and reseal the container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains Epoxy resin & Mercaptan hardener. May cause eye/skin irritation with direct contact. In case of direct eye contact, flush with water for 15 minutes and consult a physician. Wash hands and skin thoroughly with soap and water after use. If swallowed, seek medical advice immediately and show container label. Keep out of reach of children.
$12.50
You have seen 48 out of 120 products
Two-part systems mixed then poured for casting, potting and encapsulation. Measure accurately, mix thoroughly (scrape sides/base) and observe pot life, exotherm and cure schedule; consider degassing for clear casts. Use filters to refine by chemistry, cure speed and temperature rating. Always follow the product page and TDS/SDS.
