🌍 Worldwide Shipping Available | Fast & Secure Delivery ✈️

Long Open Time

33 products

  • Selleys Araldite Super Strength Epoxy Adhesive Holds 150kg Big Pack x 200ml

    Selleys Selleys Araldite Super Strength Epoxy Adhesive Holds 150kg Big Pack x 200ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Araldite Two-Part Epoxy Adhesive delivers maximum strength bonding for a wide range of materials. The mixed product gels in 2 hours, achieves initial bonding within 6–8 hours, and reaches full strength after 3 days. Features Chemical reaction of the two parts provides superior strength Bonds a wide variety of surfaces Dries clear for a clean finish Extremely strong and durable Highly water resistant – suitable for fixing tiles around pools (not below the waterline) Forms a rigid, long-lasting bond Fills small gaps – surfaces do not need to fit perfectly Excellent chemical and heat resistance Clamping recommended for a stronger bond Not suitable for Polypropylene or Polyethylene plastics Bond strength weakens above 80°C but recovers when cooled Appearance Translucent Where to Use Load-bearing repairs Fixing loose table or chair legs Reattaching hammer heads Bonding aluminium sheets Timber repairs on boats Repairing splits and cracks in cricket bats Bonding fibreglass sheets or skis Securing Dynabolts and metal rods into concrete Suitable Materials Glass Metal Wood Fabric Rigid plastic (except Polyethylene and Polypropylene) Crystal Leather Directions for Use Ensure all surfaces are clean, dry, and free of grease, rust, and paint. For best results, roughen smooth surfaces after cleaning. Dispense equal parts of Part A and Part B onto a clean, disposable surface (e.g. polyethylene or cardboard). Mix thoroughly using a spatula, nail, or stick. Apply immediately to both surfaces and press together. Clamp for 6–8 hours while the bond sets. Remove excess adhesive and clean tools immediately. Replace the correct caps on each tube to prevent hardening. Handy Tips Mix in small quantities for maximum working time – larger mixes cure faster. Replace caps immediately after use and wipe nozzles with acetone or nail polish remover. Do not swap caps between tubes – lids and tubes are colour coded. Uncured Araldite can be wiped off with acetone or nail polish remover. Once cured, remove mechanically by scraping or sanding – solvents will not dissolve it. To reposition a cured bond, heat gradually to 150°C (if the item is heat resistant), reposition, and allow to cool. For surface prep: use Selleys Liquid Sugar Soap on porous materials, or Methylated Spirits on non-porous surfaces. Use Selleys Kwik Strip Smart to remove tough residues if needed. Safety Tips Avoid contact with skin and eyes. Avoid breathing vapours. Do not use solvents near eyes or open wounds. In case of eye contact, rinse with water for at least 15 minutes and seek medical advice. Non-toxic once fully cured. Refer to the Material Safety Data Sheet for more details. Storage & Reuse Ensure caps are replaced tightly after use and store in a cool, dry place.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $76.88

  • Araldite Super Strenght Expoxy Adhesive Holds Heavy Loads Up to 150Kg 24ml

    Selleys Araldite Super Strenght Expoxy Adhesive Holds Heavy Loads Up to 150Kg 24ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6–8 hours, with maximum bond strength after 3 days. Features Stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries clear Very strong and durable bonding High water resistance (suitable for tiles around pools, but not below the water line  for that use Selleys Knead It Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat resistant Clamping recommended for stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but is regained when temperature drops Appearance Translucent Where Can This Product Be Used? Load-bearing repairs Gluing the head back on a hammer Fixing loose table or chair legs Bonding aluminium sheeting Bonding timber on boats Repairing splits and cracks in cricket bats Bonding fibreglass sheets Repairing skis Fixing Dynabolts and metal rods into concrete Suitable Materials Glass Metal Wood Fabric Rigid plastics (except Polyethylene and Polypropylene) Crystal Leather How to Use Ensure all surfaces are clean, dry, and free from grease, rust, or paint. For best results, roughen smooth surfaces after solvent cleaning. Dispense equal volumes of Part A and Part B onto a clean disposable surface (e.g. cardboard or polyethylene) and mix thoroughly. Apply adhesive immediately to both surfaces and press together. Clamp the bond for 6–8 hours while setting. Scrape off excess adhesive and clean utensils immediately. Handy Tips Mix in small quantities for longer working time — large mixes cure faster. Replace caps immediately after use and wipe nozzles with acetone or nail polish remover before sealing. Ensure caps are placed on the correct tubes (they are colour-coded). Remove uncured adhesive with acetone or nail polish remover. Once cured, remove by mechanical scraping or sanding — solvents will not dissolve the product. To reposition a cured bond, heat slowly to at least 150°C (if safe for the material), then scrape off excess and reposition carefully. For cleaning surfaces before use: Porous surfaces use Selleys Liquid Sugar Soap Non-porous surfaces (e.g. glass, metal) — clean with methylated spirits For stubborn residue use Selleys Kwik Strip Smart Ensure the surface is dry before applying. Safety Tips Avoid contact with skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of eye contact, flush with water for 15 minutes and seek medical attention. Non-toxic when set. Refer to the Material Safety Data Sheet (MSDS) for more information. Storage & Reuse Replace caps tightly after use. Store in a cool, dry place.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $24.50

  • Araldite Super Strenght Expoxy Adhesive Maximum Bond 35ml

    Selleys Araldite Super Strenght Expoxy Adhesive Maximum Bond 35ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $29.36

  • Packshot of Selleys Direct Stick Timber Flooring Adhesive Sausage 700g

    Selleys Selleys Direct Stick Timber Flooring Adhesive Sausage 700g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Liquid Nails Direct Stick Liquid Nails Direct Stick is a high strength polyurethane flooring adhesive designed for timber strip flooring and parquetry. Its semi rigid formula delivers a strong bond that helps reduce cupping and rafting. A controlled foaming action fills minor gaps. Fast cure means most floors can be sanded the next day to keep your project moving. Key Features High strength bond for timber flooring Semi rigid formula to help reduce cupping and rafting Foaming action fills small gaps and irregularities Fast cure so you can sand the next day Easy application with a strip flooring or parquetry trowel Where It Works Timber strip flooring Parquetry installations Interior floors on suitable, dry substrates Technical Details Technology Polyurethane adhesive Cure time Overnight under normal conditions. Sand and finish the next day. Application temperature 10°C to 30°C Coverage 2 m² per 1 L using the correct trowel 20 m² per 10 L using the correct trowel Clean up Protect adjacent finishes. Wipe fresh adhesive from surfaces before cure. Important Information Apply with a strip flooring or parquetry trowel to achieve stated coverage. Floors can usually be sanded the next day after proper cure. Protect surrounding finishes from expansion during foaming. Limitations Not suitable for wet or damp substrates. Avoid application below 10°C. Directions for Use Prepare the surface. Ensure substrates are clean, dry, sound, and free from dust, oil, and contaminants. Apply adhesive. Use the correct strip flooring or parquetry trowel. Spread adhesive evenly within the working time. Lay flooring. Place boards or parquetry into the wet adhesive. Press firmly to ensure full contact and adhesive transfer. Allow to cure. Leave to cure overnight under recommended conditions. Finish. Sand and finish the floor as required once the adhesive has cured. Good to Know Semi rigid bond helps manage seasonal timber movement. Foaming action assists with minor surface irregularities and gap filling. For best results, follow timber flooring manufacturer guidelines and site preparation standards. Available sizes: typically 1 L and 10 L tubs. Check current availability on this page before ordering.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $13.34

  • Packshot of Dunlop Premixed Resaflex Wall & Floor Tile Adhesive 15kg

    Dunlop Dunlop Premixed Resaflex Wall & Floor Tile Adhesive 15kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Premixed Resaflex Tile Adhesive Ready to use, flexible and tough ceramic tile adhesive for dependable indoor tiling. Ideal for interior walls and fibre-cement sheet residential floors. No mixing required, spreads smoothly, and delivers a secure bond when applied at the correct bed thickness. Key Benefits Ready mixed convenience for faster start and less mess Flexible bond that helps accommodate minor movement Non-slump paste with excellent grab on vertical surfaces Suitable for common interior wall substrates and fibre-cement sheet floors Where To Use Walls: Interior applications on cement render, plasterboard, and fibre-cement sheet Floors: Residential fibre-cement sheet floors Tiles: Ceramic and similar porous tiles Surface Preparation Surfaces must be flat, clean, dry and firmly fixed. Remove dust, oil, grease and loose materials. Prime porous surfaces like cement render and fibre-cement sheet, and any base jointing compound on plasterboard, then allow to dry. Remove water based paints completely. If paint integrity is uncertain, roughen or remove. Application Use an appropriate notched trowel: as a guide 6 mm for walls, 10 mm for floors. Spread only as much as you can tile within open time, typically about 1 m² at a time. Ensure no skin has formed. Bed tiles into a 1.5 mm to 6 mm adhesive layer. Press and slide to ensure full contact. Clean excess adhesive from tile faces and joints before it sets. Coverage Guide Tile Size Notch Size Approx. Coverage per kg Up to 150 x 150 mm 4.5 mm ~0.7 m² 150 x 150 to 250 x 250 mm 6 to 8 mm ~0.5 m² 250 x 250 mm and over 10 to 12 mm ~0.3 m² Coverage varies with substrate condition, trowel angle and application technique. Drying and Grouting Typical set time is about 24 hours at 23°C and 50% relative humidity. Allow longer for dense tiles or cool and humid conditions. Grout after adhesive has set, usually after 24 hours. Movement Joints Provide joints around perimeters and at intervals consistent with good tiling practice, for example at about 5 m on floors and about 3.5 m along walls. Keep joints about 6 mm wide and free of adhesive and grout. Fill with a suitable flexible sealant. Limitations Not suitable over concrete where extended drying can occur. Not for areas subject to water immersion such as pools. Do not use for non-porous tiles over non-porous substrates or for moisture-sensitive stone. Final adhesive bed must be at least 1.5 mm and not more than 6 mm thick. Clean Up Clean tools and any fresh residue with water before the adhesive sets. Technical Data Type Single part viscous paste Colour Grey Bulk Density ~1.2 g/cm³ pH ~8.5 Slip 0 mm Extended Open Time ~1.2 MPa after 30 min Shear Bond Strength ~0.9 MPa Pack Sizes and Shelf Life Available in 1 kg, 4 kg, 10 kg and 20 kg pails Shelf life 12 months in unopened packaging stored in a dry place Good Practice Tips Use tile spacers for consistent joints and remove them before grouting. Prime porous substrates as directed for best results. Always follow movement joint requirements for long-term performance.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $79.80

  • Packshot of Dunlop Vinyl Adhesive 4L

    Dunlop Dunlop Vinyl Adhesive 4L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $84.98

  • Packshot of Dunlop Vinyl Adhesive 1L

    Dunlop Dunlop Vinyl Adhesive 1L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $27.85

  • Packshot of Dunlop Multipurpose Carpet & Cork Adhesive 1L

    Dunlop Dunlop Multipurpose Carpet & Cork Adhesive 1L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    High strength, water based adhesive for carpet and cork Dunlop Multipurpose Carpet & Cork Adhesive is a water based, high strength adhesive designed for installing smooth or textured backed carpets and cork tiles. It delivers excellent wet grab and reliable bond on prepared subfloors. Suitable Surfaces Concrete Marine plywood Fibre cement sheet Key Features Water based and low odour High initial grab for reduced slippage Repositioning window up to 60 minutes Install immediately into wet adhesive for most carpets For cork or stiff backings, allow 10 to 15 minutes tack time before laying Coverage Approx. 2.5 m² per litre with a 3.2 mm V notch trowel Approx. 3.5 m² per litre with a 2.4 mm V notch trowel Application Ensure subfloor is dry, smooth, clean and protected from moisture. Prime highly porous concrete or timber before applying. Spread an even coat with the recommended V notch trowel. Lay carpet into the wet film. For cork or stiff backings, wait until the adhesive becomes tacky. Roll in both directions with a suitable drum roller to ensure full transfer. Set and Traffic Times No foot traffic for 24 hours Heavy traffic after 48 hours Avoid water and cleaning for 48 hours Clean Up Clean tools immediately with warm soapy water Remove dried residue with mineral turps Storage Shelf life up to 12 months in an unopened container stored at around 23°C. Good To Know Apply between 10°C and 30°C. Coverage varies with subfloor condition and trowel technique.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $29.41

  • Packshot of Selleys Araldite Extra Time Epoxy Adhesive 200ml

    Selleys Selleys Araldite Extra Time Epoxy Adhesive 200ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Araldite Extra Time Epoxy Adhesive 200ml Araldite Extra Time is a strong two part epoxy that gives you an extended working time of up to 60 minutes. It is ideal for complex or multi piece assemblies where accurate positioning matters. Once cured it forms a tough, durable bond that dries translucent. Why you will love it Extended working time of 60 minutes for precise assembly Holds up to 150 kg per cm² when fully cured on clean, abraded steel Dries translucent for a neat finish Versatile bonding across common materials Suitable materials Wood, metal, masonry, china, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. Pre test on leather and rubber for suitability. Typical uses Furniture repairs and assemblies Fixing metal or timber components General household, hobby, and craft bonding Repairs on masonry, ceramics, and glass where a clear finish is preferred Directions Surface prep: abrade, clean, and dry both surfaces. Pierce each tube using the spike in the cap. Dispense equal parts onto a clean disposable surface. Mix thoroughly. Leave for 5 minutes, then mix again before applying. Mixed glue is usable for about 1 hour at 20°C. Do not use the plastic blister to mix. Apply to both surfaces and join. Support if needed to prevent movement. Avoid strain for 6 to 8 hours. Full strength develops after 24 to 72 hours depending on conditions. Replace caps on the correct tubes to avoid cross contamination. Clean up Wipe away uncured adhesive with acetone. Once cured, mechanical removal is required. Key specs Technology Two part epoxy Working time Up to 60 minutes Initial handling 6 to 8 hours Full cure 24 to 72 hours Bond strength Up to 150 kg per cm² on abraded steel when fully cured Appearance Dries translucent Temperature resistance Up to 80°C. Bond may soften above this but strength returns when temperature normalises. Pack size 200 ml Good to know Allow longer bonding times in colder weather. Product may discolor with UV exposure. Store in a cool dry place.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $66.48

  • Packshot of Dunlop Pressure Sensitive Carpet Tile Adhesive 2L

    Dunlop Dunlop Pressure Sensitive Carpet Tile Adhesive 2L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Pressure Sensitive Carpet Tile Adhesive 2L Dunlop Carpet Tile Adhesive is a high strength, water based pressure sensitive adhesive designed for carpet tiles and double bonded underlay systems. It tacks off to a clear, dry-to-touch film that grips firmly yet allows tiles to be lifted and replaced for maintenance. Key features Pressure sensitive grab for secure hold and easy tile replacement Water based, low odour, easy to apply Suitable for smooth or textured tile backings and composition vinyl tiles Works with double bonded underlays in commercial fitouts Suitable substrates Concrete, plywood, fibre cement sheet, compressed fibre cement, and suitable underlay sheets. Subfloors must be dry, smooth, clean, and prepared to AS 1884 requirements including moisture testing. Coverage Approx. 10 m² per 2 L using a 1.6 mm V notched trowel Approx. 14 m² per 2 L using a long nap roller Drying and traffic Allow adhesive to become tacky and transparent before laying tiles. Typical tack off time is 2 to 4 hours depending on conditions. Heavy foot traffic after 24 hours Avoid wet cleaning or water exposure for 48 hours Application guide Prepare the subfloor. Prime very porous substrates if required. Treat rising damp or green concrete with a suitable moisture barrier. Apply adhesive evenly: Textured backs, composition vinyl tiles, and double bond underlays: 1.6 mm V notched trowel held at about 60 degrees Smooth backed tiles: long nap roller Wait until the film is tacky and clear with no transfer to fingertips. Early placement into wet adhesive will create a more permanent bond. Lay tiles, cut and reposition as required, then roll in both directions with a suitable roller to ensure full contact. Clean up Clean tools immediately with warm soapy water. Remove dried residue with mineral turps. Storage and shelf life 12 months in unopened packaging when stored in a cool, dry place at about 23°C and 50% RH. Good to know Do not apply below 15°C or above 30°C surface temperature. Not suitable for traditional carpet-to-underlay stretch-in installations. For double bond systems, follow the flooring manufacturer’s instructions. Safety Wear gloves and eye protection, ensure adequate ventilation, and keep out of reach of children. If eye contact occurs, rinse with water and seek medical advice if irritation persists.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $38.56

  • Packshot of Gorilla Ultimate Strong Wood Glue 532 mL

    Gorilla Gorilla Ultimate Strong Wood Glue 532 mL

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Gorilla Ultimate Strong Wood Glue 532 mL is a reliable high performance wood glue for interior and exterior carpentry chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 532 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Gorilla Ultimate for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Gorilla Ultimate Strong Wood Glue 532 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Furniture build and repair Edge bonding and laminations Cabinetry and joinery where water resistance is valued Suitable surfaces The adhesive works well on the following surface types when properly prepared: Hardwoods and softwoods Plywood and MDF Veneers and end grain with correct technique Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of typically 5 to 10 minutes depending on temperature. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Open time allows assembly before clamping. Forms a strong cross linked bond that is water resistant when fully cured. Temperature and environmental performance Use above 10 C and avoid freezing conditions while curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wipe squeeze out with a damp cloth while wet. Scrape or sand once cured. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Close the cap tightly and store upright. Do not allow the nozzle to clog; remove dried film if present. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $25.20

  • Weldbond Steel Tough Welbond Universal Adhesive Tube 60ml

    Weldbond Weldbond Steel Tough Welbond Universal Adhesive Tube 60ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications. Same formula & product you trust, just better looking! Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable. Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age. It is non-toxic, non-flammable & Solvent free 3-4 times stronger than standard P.V. High Solid content (51-53%) means more glue and it goes a lot further Does everything a P.V.A does, plus more Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $8.13

  • Weldbond Steel Tough Welbond Universal Adhesive Tube 3Lt

    Weldbond Weldbond Steel Tough Welbond Universal Adhesive Tube 3Lt

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications. Same formula & product you trust, just better looking! Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable. Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age. It is non-toxic, non-flammable & Solvent free 3-4 times stronger than standard P.V. High Solid content (51-53%) means more glue and it goes a lot further Does everything a P.V.A does, plus more Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $103.00

  • The Original Super Glue Single Use 4 Hours Anchor-Tite Waterproof Epoxy 4g The Original Super Glue Single Use 4 Hours Anchor-Tite Waterproof Epoxy 4g

    The Original Super Glue The Original Super Glue Single Use 4 Hours Anchor-Tite Waterproof Epoxy 4g

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Single Use Waterproof Epoxy Adhesive is the perfect product to use when you need to do any marine or waterproof projects. It works under or in the presence of water and remains waterproof. Package contains just the right amount of product for most small projects. The metal tubes dispense effortlessly and are easy to mix. This product sets in only 3-4 hours. 

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $29.00

  • The Original Super Glue 30 minute Delayed Setting Epoxy with Easy Open Cap 28.3g The Original Super Glue 30 minute Delayed Setting Epoxy with Easy Open Cap 28.3g

    The Original Super Glue The Original Super Glue 30 minute Delayed Setting Epoxy with Easy Open Cap 28.3g

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Extra Setting Time Epoxy Adhesive is the perfect product to use when you need more time to work to get your project pieces in place. This product allows you 30 minutes to arrange and rearrange pieces. Cures in a light yellow color. Works best on: • All Purpose • Ceramic • Glass • Wood • Leather • Fiberglass • Metal • Most Plastics Properties: Initial color: Clear hazy to light yellow  Final color: Light yellow Hardness, Shore D: 75-83 (After full cure) Set Time: 30 minutes @ 65-80F Shear Strength, Steel: 2000 psi (± 20%) Handling Time: After 7 hours Aluminum: 1400 psi (± 20%) Full Strength: 24 hours Operating Temperature Range:-650  to 2250 F  (-54 0  to 1070 C) Use: 1. Surfaces should be clean and dry, free from oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from container following package directions & mix thoroughly, for about 1 minute. 4. Apply to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 30 minutes at room temperature (77F or 25C) with full cure in 24 hours. Storage After use, wipe tips to remove residual product and reseal the container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains Epoxy resin & polyamine hardener. May cause eye/skin irritation with direct contact. In case of direct eye contact, flush with water for 15 minutes and consult physician. Wash hands and skin thoroughly with soap and water after use. If swallowed, seek medical advice immediately and show container label. Keep out of reach of children. 

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $15.00

  • Sika SikaTitan 258 Primerless Windscreen Adhesive 310ml

    Sika Sika SikaTitan 258 Primerless Windscreen Adhesive 310ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    SikaTitan® 258 is a primerless to windscreen, one-component direct glazing adhesive. It is easy to apply and has a paste-like consistency. On exposure to atmospheric moisture it cures to a durable elastomer. SikaTitan® -258 provides a long tack-free time and ensures a safe application even under warm conditions. Note: Primerless application requires the glass to be prepared with a non-antistatic glass cleaner. Also the bonding surfaces must be free of contamination prior to the application of the adhesive. SikaTitan® -258 is manufactured in accordance with ISO 9001 / 14001 quality assurance system and with the responsible care program. Product Benefits - Primerless to glass - One-component formulation - Cold application - Good application properties such as bead stability / good non-sag properties - Short cut-off string - Tested according to FMVSS 212/208 (with double-side airbags, no seatbelts) Areas of Application SikaTitan® -258 is suitable for direct-glazing applications in the Automotive Glass Replacement business. With its good performance and application properties it is suitable for mobile as well as inhouse installations.This product is to be used by professional experienced fitters only. If this product is used for other applications than Automotive Glass Replacement, trials must be carried out prior to use. Technical Product Data Chemical base 1-C polyurethane Colour (CQP1) 001-1) Black Cure mechanism Moisture-curing Density (uncured) (CQP 006-4) 1.1 kg/l approx. Non-sag properties (CQP 061-1) Good Application temperature +5 to +40°C Skin time2) (CQP 019-1) 40min. approx. Open time2) (CQP 526-1) 30min. approx. Curing speed(CQP 049-1) Shore A hardness (CQP 023-1 / ISO 868) 51 approx. Tensile strength (CQP 036-1 / ISO 37) 5 MPa approx. Elongation at break (CQP 036-1 / ISO 37) 650% approx. Tensile lap-shear strength (CQP 046-1 / ISO 4587) 2.5 MPa approx. Safe Drive-Away Time2) (cars) with double side airbag according to FMVSS 212 / 208 (CQP 511-1) without airbag 6 hours 2 hours Chemical Resistance SikaTitan® -258 is resistant to fresh water, seawater, limewater, sewage effluent, diluted acids and caustic solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic acids and caustic solutions or solvents.   Method of Application Removal of old glass Remove damaged glass in accordance with the vehicle manufacturer’s instructions. Surface preparation Surfaces must be clean, dry and free from dust and grease. The bond faces must be prepared with a non-antistatic glass cleaner. Bonding surface must be free of contaminants before application of the product. Windshields without ceramic coatings need additional UV protection. Application Cut off the tip of the nozzle in accordance with the vehicle manufacturer's recommendations and screw onto the cartridge. It is recommended to apply the adhesive with a piston-type application gun. To ensure a uniform thickness of adhesive bead, we recommend that the adhesive be applied in the form of a triangular bead (see fig. 1 below). The substrate temperature must be between 5°C and 35°C.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $43.58

  • Selleys Special Putty Premium Linseed Oil Formula 450g

    Selleys Selleys Special Putty Premium Linseed Oil Formula 450g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour. Features Easy to use. Can be applied by hand or with a putty knife Product has exceptional keeping qualities Available in a natural colour Superior grade putty Where can this putty be used? A wood sash putty that is excellent for glazing wooden windows and doors Bedding glass beads Not recommended for use with heat absorbing glass If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes Not recommended for use where structural movement may occur Not recommended for use in metal framed windows. What materials is this putty suitable for? Wood Timber How to use this product Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing. Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used. Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass. Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing. Paint should be carried out 2mm above the top line of the putty. Handy tips Do not use kerosene, turps or other material to aid in working the putty Allow putty to skin before applying paint Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it. Putty must be painted in exterior applications. High humidity, cold weather and use in interior applications can extend skinning times. Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil. Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen. Safety tips Low hazard material For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $9.00

  • Selleys Special Putty Premium Linseed Oil Formula 2Kg

    Selleys Selleys Special Putty Premium Linseed Oil Formula 2Kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour. Features Easy to use. Can be applied by hand or with a putty knife Product has exceptional keeping qualities Available in a natural colour Superior grade putty Where can this putty be used? A wood sash putty that is excellent for glazing wooden windows and doors Bedding glass beads Not recommended for use with heat absorbing glass If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes Not recommended for use where structural movement may occur Not recommended for use in metal framed windows. What materials is this putty suitable for? Wood Timber How to use this product Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing. Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used. Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass. Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing. Paint should be carried out 2mm above the top line of the putty. Handy tips Do not use kerosene, turps or other material to aid in working the putty Allow putty to skin before applying paint Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it. Putty must be painted in exterior applications. High humidity, cold weather and use in interior applications can extend skinning times. Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil. Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen. Safety tips Low hazard material For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $41.00

  • Putty Premium Linseed Oil For Glazing Woodfilling Plumbing 2Kg

    Prep Putty Premium Linseed Oil For Glazing Woodfilling Plumbing 2Kg

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    In keeping with the traditional formula, PREP Linseed Oil Putty is manufactured to the highest standards for almost all situations where a reliable linseed oil-based putty is required. Applications include; window glazing, filling nail holes in furniture, flooring, and general building applications. Environmentally friendly Non-toxic Tough & flexible Easy to use Weather-resistant

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $19.17

  • Last stock! Prep Traditional Putty Premium Linseed Oil Formula For Glazing Woodfilling Plumbing 400g

    Prep Prep Traditional Putty Premium Linseed Oil Formula For Glazing Woodfilling Plumbing 400g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    In keeping with the traditional formula, PREP Linseed Oil Putty is manufactured to the highest standards for almost all situations where a reliable linseed oil-based putty is required. Applications include; window glazing, filling nail holes in furniture, flooring, and general building applications. Environmentally friendly Non-toxic Tough & flexible Easy to use Weather-resistant

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $7.50

  • Polyfilla Skim Coat 510g: The Ultimate Smooth Surface Maker for a Flawless Paint Job

    Poly Polyfilla Skim Coat 510g: The Ultimate Smooth Surface Maker for a Flawless Paint Job

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Polyfilla Skim Coat 510g: The Ultimate Smooth Surface Maker for a Flawless Paint Job Seamless Filler for Pro-Level Paint Preparations When it comes to ensuring the best possible surface for your painting projects, look no further than Polyfilla Skim Coat 510g. This product excels in filling small cracks, dents, and fine imperfections, setting the stage for a smooth paint application. Key Features: Extremely easy to sand Sets to a super hard finish Highly crack resistant Ready to use, dries in just 2 hours For use exclusively on interior plasterboard & gyprock How to Use: Make sure the surface is clean, dry, and free from loose material. Press the filler firmly into cracks and holes. For larger areas, use a trowel to spread evenly. Let it dry for 2-3 hours depending on the humidity. Sand it for a smooth finish before painting. For optimal results, apply a paint undercoat before using water or oil-based paint top coat. Limitations & Tips: Use Poly Gap filler or silicone sealant for areas with joint movement. Clean up immediately with water before the filler dries. For hairline cracks, consider using Poly Small Cracks filler for a comprehensive solution. Polyfilla Skim Coat 510g is your definitive choice for a crack-free, smooth surface, ready to be painted. It's your gateway to perfection!

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $20.22

  • Polyfilla Skim Coat 1.2kg: The Ultimate Smooth Surface Maker for a Flawless Paint Job

    Poly Polyfilla Skim Coat 1.2kg: The Ultimate Smooth Surface Maker for a Flawless Paint Job

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Polyfilla Skim Coat 1.2kg: The Ultimate Smooth Surface Maker for a Flawless Paint Job Seamless Filler for Pro-Level Paint Preparations When it comes to ensuring the best possible surface for your painting projects, look no further than Polyfilla Skim Coat 1.2kg. This product excels in filling small cracks, dents, and fine imperfections, setting the stage for a smooth paint application. Key Features: Extremely easy to sand Sets to a super hard finish Highly crack resistant Ready to use, dries in just 2 hours For use exclusively on interior plasterboard & gyprock How to Use: Make sure the surface is clean, dry, and free from loose material. Press the filler firmly into cracks and holes. For larger areas, use a trowel to spread evenly. Let it dry for 2-3 hours depending on the humidity. Sand it for a smooth finish before painting. For optimal results, apply a paint undercoat before using water or oil-based paint top coat. Limitations & Tips: Use Poly Gap filler or silicone sealant for areas with joint movement. Clean up immediately with water before the filler dries. For hairline cracks, consider using Poly Small Cracks filler for a comprehensive solution. Polyfilla Skim Coat 1.2kg is your definitive choice for a crack-free, smooth surface, ready to be painted. It's your gateway to perfection!

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $35.69

  • Polyfilla Putty Filler Oil Based Paintable Durable Wood and Metal Exterior 450g

    Poly Polyfilla Putty Filler Oil Based Paintable Durable Wood and Metal Exterior 450g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A high grade linseed oil putty with excellent adhesion for repairing and glazing wood and metal frames. For use on: Wood & metal (EXTERIOR & INTERIOR) Dries in: Skins over in 2-3 days depending on weather conditions. Ready to use: YES Colour: Light brown Ensure all surfaces are clean, sound and dry. Remove all old putty, dust off loose and crumbling material. • Bare timber should be primed with an oil-based primer before applying putty. • Knead putty thoroughly for smooth, even consistency in application. • Apply putty to working area with either a thumb or putty knife. When evenly applied, smooth off. • Always allow several days for putty to skin before applying an oil-based undercoat. Can be painted with either water or oil-based topcoat. Q. I used Polyfilla Putty on a window frame and have noticed some wrinkling on the surface. Is something wrong with the product? A. No. When this product is used on metal window frames exposed to heat, some surface wrinkling can occur. This will not affect the performance of the putty in any way.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $13.53

  • Polyfilla Putty Filler Oil Based Paintable Durable Wood and Metal 2Kg

    Poly Polyfilla Putty Filler Oil Based Paintable Durable Wood and Metal 2Kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A high grade linseed oil putty with excellent adhesion for repairing and glazing wood and metal frames. For use on: Wood & metal (EXTERIOR & INTERIOR) Dries in: Skins over in 2-3 days depending on weather conditions. Ready to use: YES Colour: Light brown Ensure all surfaces are clean, sound and dry. Remove all old putty, dust off loose and crumbling material. • Bare timber should be primed with an oil-based primer before applying putty. • Knead putty thoroughly for smooth, even consistency in application. • Apply putty to working area with either a thumb or putty knife. When evenly applied, smooth off. • Always allow several days for putty to skin before applying an oil-based undercoat. Can be painted with either water or oil-based topcoat. Q. I used Polyfilla Putty on a window frame and have noticed some wrinkling on the surface. Is something wrong with the product? A. No. When this product is used on metal window frames exposed to heat, some surface wrinkling can occur. This will not affect the performance of the putty in any way.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $46.19

  • PC Concrete No Shrink Wet or Dry 40g

    PC Products PC Concrete No Shrink Wet or Dry 40g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    PC-Concrete ™ Anchoring and Crack Filling Epoxy— is the epoxy chosen to repair cracks in a warehouse and factory floors. Dispense and apply using a standard size caulking gun. Cures hard enough to drive over within 3 hours at standard temperature. Nothing stronger for your anchoring applications. PC-Concrete™ is a two-component (1:1 ratio), 100% solids, high modulus, and structural epoxy paste. PC-Concrete™ is a solvent-free, no odour, high strength, moisture insensitive epoxy system. The resin and hardener are uniformly dispensed from a 9-ounce cartridge system and mixed through a mixing nozzle using a standard size caulking gun. (We recommend at least an 18:1 thrust ratio). PC-Concrete™ is also provided in a 22-ounce dual cartridge system for Contractors and Professionals. This size requires a 600ml high thrust dual cartridge dispensing gun. For filling larger cracks and cavities use the 102-ounce bulk kit. PC- Concrete™ will NOT SHRINK. Suitable for Interior and Exterior applications. Can be applied to WET & UNDERWATER surfaces. Here are just a few specific uses (there are many other uses): Anchor into marine docks above or below waterline Anchor equipment to floors Bond to pre-stressed floors Anchor into stone and rock. Install anchor bolts for sill plates Anchor into foundations and block Fill cracks in concrete allowing equipment traffic In 4 hours Anchor into concrete railroad ties Anchor HVAC equipment to concrete pads and roofs Waterproof floor to wall cracks Re-anchor railing at convention center or apartment building Anchor seats in lecture hall or theaters Repair broken concrete in shopping mall parking garage Fill spalled concrete in car wash Fix fork truck damaged concrete in warehouse Seal crack in sanitation and chemical storage facility containment area Repair floor in fire station garage Anchor safe to floor prison and security pickproof epoxy Anchor machinery

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $14.46

  • MG Chemicals Thermally Conductive Adhesive 4 Hours 6ml #8329TCS-6ML

    MG Chemicals MG Chemicals Thermally Conductive Adhesive 4 Hours 6ml #8329TCS-6ML

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    This is a two-part, smooth, dark grey paste that cures to form a hard, durable polymer that is extremely thermally conductive, yet electrically insulating. It is it very viscous because it is highly filled with thermally conductive ceramic powders for maximum thermal conductivity. It bonds well to metals, ceramics, glass, and most plastics used in electronic assemblies. It has a convenient 1-to-1 mix ratio and a 4-hour working life. The mixed adhesive can essentially act like a one-part adhesive for the duration of a work shift. Unlike one-part adhesives, it does not require high curing temperatures or frozen storage, and it has a very long shelf life. This product comes packaged in separate 3 mL graduated syringes that can be accurately dispensed Applications & Usages This product is designed to bond heat sinks, LED’s, and other heat generating components in electronic assemblies. It is suitable for manufacturing, repair, and hobbyist sectors. Use it when a thixotropic adhesive paste with maximum thermal conductivity and a very long working life is required. For automatic dispensing applications, use the 8329TFS, which has a lower viscosity at the cost of slightly lower thermal conductivity. Benefits and Features • Thermal conductivity: 1.44 W/(m·K) • 1:1 mix ratio by volume • Working life: 4 hours • Cure time 1 hour at 80°C or 96 hours at room temperature • Room temperature storage • Good adhesive strength • Strong resistance to water, brine, acids, bases, and aliphatic hydrocarbons Usage Parameters Properties Value Working Life a) 4 h Full Cure @25 °C [77 °F] 96 h Full Cure @80 °C [176 °F] 1 h Properties Value Constant Service -65 to 165 °C Temperature [-85 to 329 °F] Intermittent Temp. -70 to 200 °C Limits b) [-40 to 302 °F] Storage Temperature 22 to 27 °C of Unmixed Parts [72 to 81 °F]

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $39.95

  • Loctite MR 5923 Aviation Gasket Non-Hardening Sealant 50ml

    Loctite Loctite MR 5923 Aviation Gasket Non-Hardening Sealant 50ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    LOCTITE® MR 5923 is a dark reddish-brown, viscous liquid thread sealant with a characteristic alcoholic odor. It is a slow drying liquid that changes to a pliable, tacky film through solvent evaporation. It seals close-fitting parts, machined surfaces, and threaded connections in industrial, aircraft, and marine applications. Dark reddish-brown, viscous liquid thread sealant with a characteristic alcoholic odor. For close tolerance flanges Slow drying Flexible setting LOCTITE® MR 5923™ seals close-fitting parts, machined surfaces, and threaded connections in industrial, aircraft, and marine applications. It is a slow drying liquid that changes to a pliable, tacky film through solvent evaporation. Typical applications include solid gasket dressing, close-fitting machined surfaces, threaded connections, aviation engines, and marine engines. This product is typically used in applications with an operating range of -54 °C to +204 °C. Technology Solvent-based Chemical Type Modified resin, fillers, and alcohol Appearance Brown liquidLMS Viscosity Flow similar to SAE 10 Motor Oil Cure Air dry Application Gasketing & sealing Specific Benefit ● For close tolerance flanges ● Slow drying ● Flexible setting Chemical/Solvent Resistance LOCTITE® MR 5923™ retains effective properties in contact with water, ethylene glycol, gasoline, motor oil, transmission fluid, and seawater Directions for use: 1. Remove all previous material from mating surfaces. 2. For best results, clean and prep the area with an oil-free solvent. 3. Remove cap. Coat with a brush-top applicator. 4. When used as a gasket dressing, spread product with a spatula to a uniform film on one side of the gasket and then position it on the assembly. Coat the second side of the gasket and re-assemble. Slower drying formula increases work time. 5. Assembly is operational after 4 hours, full cure is effective after 24 hours. 6. The product can be removed from metal surfaces with isopropyl alcohol. If the sealant has been dried for a long time or at high temperatures, cover the sealant with alcohol and allow it to soften overnight.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $6.67

  • Loctite Epoxy Marine 25ml

    Loctite Loctite Epoxy Marine 25ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Loctite Marine Epoxy can be applied and cured underwater and eliminates the need to drain out water before repairs. This unique epoxy is a resilient, two-part adhesive system consisting of an epoxy resin and a hardener. When mixed in equal volumes with the convenient dual-syringe applicator, the resin and hardener react to produce a tough, rigid, high strength bond that sets 2 hours and fully cures in 24 hours. Ideal for repairing PVC, copper, brass and galvanized pipes, Loctite Marine Epoxy bonds to metal, concrete, glass, fiberglass, ceramic, wood and certain rigid plastics and cures to a white finish that can be easily sanded or machined. This resilient epoxy does not shrink and is resistant to water, most common solvents, and high impact.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $30.76

  • KwikGrip Water Based High Strength Multi-purpose Contact Adhesive Dries Clear 50ml KwikGrip Water Based High Strength Multi-purpose Contact Adhesive Dries Clear 50ml

    Selleys KwikGrip Water Based High Strength Multi-purpose Contact Adhesive Dries Clear 50ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $13.11

  • KwikGrip Water Based High Strength Contact Adhesive Dries Clear 500ml

    Selleys KwikGrip Water Based High Strength Contact Adhesive Dries Clear 500ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $40.93

  • Davco SMP Evo Tile Adhesive 5kg

    Davco Davco SMP Evo Tile Adhesive 5kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Davco SMP Evo Tile Adhesive is a high-performance, flexible cement-based adhesive ideal for the installation of natural stone, porcelain, and marble tiles. Specially designed with advanced low-dust technology, it provides a cleaner and safer working environment. Its superior non-slump properties make it perfect for wall and floor tiling, including large-format tiles. Surface Preparation: Ensure surfaces are structurally sound, dry, and free from contaminants like dust, oil, and wax. Smooth surfaces should be roughened slightly, and absorbent substrates should be primed. Existing tiles must be clean, dry, and securely bonded. Mixing: Mix 5kg of powder with approximately 1.4–1.5L of clean water using a mechanical mixer until a smooth, lump-free paste is formed. Allow it to stand for 5 minutes before remixing. Do not add more water after mixing. Application: Apply the adhesive with a notched trowel over an area no larger than can be tiled within the open time. Firmly press tiles into the adhesive bed with a twisting motion to ensure full contact. Back-buttering may be necessary for large tiles or uneven substrates. Coverage: Approximately 1.5–1.75m² per 5kg bag using a 10mm notch trowel. Drying Time: Tiles can generally be grouted after 24 hours. Allow 2 days before exposure to water in wet areas and 21 days for submerged areas like pools. Clean-up: Clean tools and excess adhesive with water before it sets. Once cured, adhesive must be removed mechanically. Technical Data: Classification: C2S1TE Pot life: 1.5 hours Open time: 30 minutes Adjustability time: 20 minutes VOC content: Low Appearance: White powder

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $30.14

  • 3M Marine Flexible Adhesive Sealant 5200 White Permanent 29ml

    3M 3M Marine Flexible Adhesive Sealant 5200 White Permanent 29ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    3M™ Marine Adhesive Sealant 5200 is extremely strong and retains its strength above or below water line. Stays flexible too - allows for structural movement. Has excellent resistance to weathering and salt water.   Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Check the bonding and sealing jobs this product can handle for you: fibreglass deck to fibreglass hull, wood to fibreglass, portholes and deck fittings, motors on fibreglass transoms, under mouldings, hull seams above and below water line. Centre board trunk joints. Between struts and planking. Stern joints. Deck housing, etc. Easy to apply with manual caulking gun. Won't sag or flow in vertical or horizontal seams.   Very high strength Watertight bonds Above/Below waterline use   Specifications Adhesive Type Polyurethane Application Method Hand or pressure caulk Brand 3M™ Colour White Consumer Label Yes Cure Time 24 Hours Full Cure 3mm per 5 day Hardness 68 Shore A Industries Marine Physical Form Medium paste Product Form Cartridge Solids Weight Percent (Approximate) 97 Percent Tack Free Time 12 Hour

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $55.00

  • 3M 08116 Panel Bonding Adhesive 200ml 3M 08116 Panel Bonding Adhesive 200ml

    3M 3M 08116 Panel Bonding Adhesive 200ml

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    3M™ Panel Bonding Adhesive (PN 08116) is a two-part epoxy designed to bond non-structural outer body sheet metal such as, but not limited to, quarter panels, roof panels, van sides, box sides and door skins Product Uses Bonding steel, aluminum, SMC and FRP (fiberglass) to themselves or each other. Use with the following applicators: PN08117 (manual), PN 09930 (pneumatic). 3M™ Mixing Nozzle, PN 08193 (6/bag), PN 08194 (50/box). For professional use only. Not intended for retail sale. The following times have been determined with ambient air temperature and substrate temperature @ 70°F and are considered typical values. WORK TIME: 90-120 minutes CLAMP TIME 6 hours CURE TIME: 24 hours SURFACE PREPARATION: 1. Wash surface with soap and water to remove water soluble contaminants. Follow the soap and water wash with an appropriate VOC compliant product for removal of surface contaminants. 2. Remove all rust, primer and paint from the areas to be bonded or welded using a Scotch-Brite™ Clean & Strip Disc or 3M grade 50 Grinding Disc. 3. Straighten all metal, and “dry-fit” the parts. 4. Clamp the part in place and check for fit and alignment. 5. Remove the panel from the vehicle. All areas to be welded should be coated with 3M™ Weld-Thru II Coating (PN 05917) according to the directions on the can. Adhesive should not be applied to these areas. PRODUCT PREPARATION: 6. Place an adhesive cartridge in the applicator gun. 7. Remove the retaining collar and plug from the end of the cartridge. Discard plug, but save the retaining collar. 8. Before attaching a nozzle, “equalize” the cartridge by dispensing just enough product to be sure that both parts A and B are present at the outlet. 9. Attach a 3M™ Static Mixing Nozzle to the cartridge and lock in place with the retaining collar. 10. Dispense a small amount of material through the mixing nozzle onto a disposable surface and discard. 11. Apply an adhesive bead to all bare metal surfaces of both pieces to be bonded. Using a plastic spreader or acid brush, tool out the adhesive to cover all bare metal surfaces. 12. Apply a 1/8" diameter adhesive bead approximately 1/4" from the inside edge of the replacement panel. • Quarter Panels: Adhesive should be applied to the lower edge, the wheel opening, the door jamb areas of the quarter, and at the factory seam of the sail panel. 3M suggests that the rear vertical portion of a quarter panel should be welded. It is acceptable to bond the rear vertical portion of a quarter panel, if recommended by the OEM. Additionally, most OEM’s only recommend full panel replacement. Should you perform a belt cut on a sail panel, 3M recommends welding the belt cut to ensure optimal cosmetic appearance. All areas to be welded should be sprayed with 3M™ Weld-Thru II (PN 05917). Do not apply adhesive to these areas. • Roof Panels: Adhesive should be applied around the perimeter of the roof anel. To replace the factory-applied NVH foam/spacer between the roof bow and the roof panel, use one of the following: 3M™ Urethane Seam Sealer (PN 08360, PN 08361 or PN 08364), 3M™ MSP Seam Sealer (PN 08369 or PN 08370), or 3M™ NVH Dampening Material (PN 04274) to the roof bows as needed. • Door Skins: Adhesive should be applied to the hem flange area. To replace the factory-applied NVH foam/spacer between the intrusion beam/s and the door skin, use one of the following: 3M™ Urethane Seam Sealer (PN 08360, PN08361 or PN 08364), 3M™ MSP Seam Sealer (PN 08369 or PN 08370), or 3M™ NVH Dampening Material (PN 04274) to the intrusion beam/s as needed. 13. Clamp the panel in its proper position. 14. Tool any adhesive “squeeze out” to seal the outside of the seam all along the bonded edge of the panel. • Caution: The adhesive is combustible. Keep any MIG welding a minimum of two inches from the adhesive. As with any welding operation, keep the appropriate fire extinguisher within reach, and be alert to any smoke or flame that may be present. Resistance spot welding through uncured adhesive is acceptable. 15. Spray the inside of quarter panels, interior cavities, and any welded seams with 3M™ Rust Fighter-I (PN 08891 or PN 08892). 16. Clamps may be removed after six hours at 73°F. Parts will need to remain clamped longer if the temperature is below 73°F and/or if there is any tension on the part. The cure time may be accelerated by applying heat with a heat gun or lamps. 17. Allow 24 hours at a minimum of 73°F before returning vehicle to service. CLEAN-UP: Unmixed material may be cleaned from most surfaces with an appropriate VOC compliant product.  Storage and Handling When stored at the recommended conditions in original, unopened containers, this product has a shelf life of 24 months from the date of manufacture. Store at room temperature. Rotate stock on a “first-in-first-out” basis. After use, leave the mix nozzle in place to seal the cartridge.

    Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $160.00

A person is creating a mosaic with Glues Australia's Long Open Time glue. The bright and creative workspace shows the precision and ease of using a long open time adhesive for detailed craft projects.

Extended working time for complex assemblies, large surfaces and precise positioning. Common for contact cements, epoxies and flooring adhesives. Observe recommended open time and mating pressure for full strength. Use filters to refine by chemistry, pot life and application method. Always check the product page and TDS/SDS.

Login

Forgot your password?

Don't have an account yet?
Create account