Note: If you are working on a timber floor, you will need to use Fix-A-Floor Polyurethane for Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive, now patented, is an extra-strength bonding adhesive designed specifically for re-bonding loose and hollow tiles, marble and stone without the cost and mess of removing or replacing them. Fix-A-Floor is a simple DIY repair solution that is fast, easy and affordable, and surprisingly rewarding. If you can operate a drill, a caulking gun and mix a small batch of grout, you can do it. It works on all types of subfloor materials. Just Drill & Fill! Tip: For more precise application or smaller holes, you can include the 30 mL Adhesive Syringe with Blunt Tip Fill Needle when purchasing this product. It makes applying the adhesive cleaner and more accurate, especially in tight or narrow grout lines. The Nozzle The nozzle of the 300 mL Fix-A-Floor tube is specially engineered with a pre-drilled 3 mm hole to make it ideal for filling drilled holes in loose or hollow tile, marble and stone floors. It is firm enough to form a strong seal for optimal flow and complete coverage. Markings on the nozzle indicate cut points for 4.5 mm, 6 mm or any size you need, making it suitable for both narrow grout lines and wider applications. The Adhesive Fix-A-Floor Repair Adhesive is strong and flexible, featuring elastomeric bonding properties that prevent future issues caused by foundation movement, expansion and contraction of the subfloor or poor original installation. Used by flooring professionals for years, this product allows any homeowner to fix loose, hollow or squeaky tiles quickly and permanently. It is non-toxic, non-flammable and eco-friendly. Whether you are repairing a small area or a large floor section, Fix-A-Floor delivers lasting results and is guaranteed for the life of your floor. Just Drill & Fill! FAQs Q: Will Fix-A-Floor work with heated floors?A: Yes. Many customers use Fix-A-Floor over heated floor elements with no issues. Turn off the heating before, during and for 48 hours after applying. Q: Some of my grout is missing. Can I still use Fix-A-Floor?A: Yes. If small gaps or cracks exist, simply Drill & Fill. The adhesive will re-bond and stabilise loose areas. If the grout is completely missing, re-grout lightly, allow it to dry and then apply Fix-A-Floor. Q: Can I repair my whole floor or just one tile?A: Fix-A-Floor works on all sizes of problem areas, from a single tile to an entire room. It is suitable for all types of tile, marble and stone floors. Q: Can I use Fix-A-Floor outside?A: Yes. It performs well in both interior and exterior applications, including patios and decks. Q: Can I use Fix-A-Floor in showers or pools?A: No. It is not recommended for areas exposed to constant or excessive moisture. Q: Is Fix-A-Floor safe?A: Yes. It is a non-toxic, non-flammable, water-based adhesive that is safe and environmentally friendly. Q: Can I use it to re-glue a tile that has come loose?A: Yes. Apply Fix-A-Floor directly to the floor where the tile was, press the tile firmly into place, apply weight and allow to cure for 24 hours. Q: Do I need to place weight on the floor after filling?A: It is recommended to place some weight, such as a heavy object or bucket, on the area to aid curing and ensure even distribution. It is not mandatory but helps achieve optimal results. Q: What if adhesive does not appear from other holes?A: The adhesive may still be spreading beneath the tile. Move to the next hole and continue filling. Make sure you are not pressing the nozzle down onto the subfloor during application.
$34.95
Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$23.00
Sikaflex®-291 Black Marine-Grade Polyurethane Sealant 150mL is a premium, one-component, non-sag adhesive sealant specially formulated for marine environments. It cures on exposure to atmospheric moisture, forming a strong, elastic, and durable bond that resists saltwater, vibration, and weathering. Trusted by boat builders and marine professionals worldwide, Sikaflex®-291 meets International Maritime Organisation (IMO) standards for safety and performance. Features & Benefits Marine-grade polyurethane formula with superior adhesion Excellent weathering and saltwater resistance Elastic and vibration-resistant for long-lasting seals Low odour and non-corrosive composition Can be sanded and overpainted after curing Maintains flexibility across wide temperature ranges Where to Use Sealing and bonding on boats, yachts, and marine structures Deck fittings, hatches, and hardware installations Elastic, vibration-resistant joints above and below deck Bonding wood, metals, primers, coatings, ceramics, and GRP plastics Important Notes Not suitable for plastics prone to stress cracking such as Plexiglas or Polycarbonate Surfaces must be clean, dry, and free from grease or dust before application Recommended application temperature: 5°C to 40°C Technical Details Chemical Base 1-component polyurethane Colour Black Cure Mechanism Moisture-curing Density (uncured) Approx. 1.3 kg/L Shore A Hardness 40 Tensile Strength 1.8 MPa Elongation at Break 500% Temperature Resistance -50°C to +90°C (up to 180°C short term) Skin Time Approx. 60 minutes Shelf Life 12 months (stored below 25°C) Packaging 150 mL Tube For marine sealing and bonding you can trust, Sikaflex®-291 delivers professional-grade strength, flexibility, and durability on every project.
$18.70 $0.12/ml
The unique rubber-infused gel formula allows powerful bonds that are extremely precise even on flexible materials. Ideal for porous and vertical surfaces, and strong enough to withstand extreme conditions. The gel’s high strength non-drip formula then dries transparent to form invisible bonds that give a long lasting durability that is both weather and shock-resistant. For intricate, hard to reach spots, Loctite Power Flex Gel Control features an easy grip squeeze bottle and nozzle for precise applications. Recommended on: Rubber, Leather, Wood, Metal, Porcelain, Paper, Plastic. Properties: -Rubber infused gel formula for extra strong and flexible bonds -Ideal for porous and vertical surfaces -Water resistant -Bonds in seconds -Withstands heavy loads -Dries transparent -Easy to open, self-piercing and anti-clog cap -Choice of applicators: convenient tube or easy grip control with a longer nozzle -Suitable for use on most surfaces* -Solvent-free -* Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Step by Step Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$12.50 $10.95
![Fix-A-Floor Loose Tile Repair Adhesive Needle [Pro Pack] Includes a Micro Syringe Injector and Drill Bit](http://gluesaustralia.com.au/cdn/shop/files/One_33b7ac3c-91f8-445e-9f7a-f35eb32fd49e.jpg?v=1760493150&width=645)
![Fix-A-Floor Loose Tile Repair Adhesive Needle [Pro Pack] Includes a Micro Syringe Injector and Drill Bit](http://gluesaustralia.com.au/cdn/shop/files/513iY1tnifL._SL1013_2cc193b4-9c50-4e36-a6e8-69a36d42769f.jpg?v=1760493150&width=645)
Note: If you are working on a timber floor, you will need to use Fix-A-Floor Polyurethane for Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive, now patented, is an extra-strength bonding adhesive designed specifically for re-bonding loose and hollow tiles, marble and stone without the cost and mess of removing or replacing them. Fix-A-Floor is a simple DIY repair solution that is fast, easy and affordable, and surprisingly rewarding. If you can operate a drill, a caulking gun and mix a small batch of grout, you can do it. It works on all types of subfloor materials. Just Drill & Fill! Tip: For more precise application or smaller holes, you can include the 30 mL Adhesive Syringe with Blunt Tip Fill Needle when purchasing this product. It makes applying the adhesive cleaner and more accurate, especially in tight or narrow grout lines. The Nozzle The nozzle of the 300 mL Fix-A-Floor tube is specially engineered with a pre-drilled 3 mm hole to make it ideal for filling drilled holes in loose or hollow tile, marble and stone floors. It is firm enough to form a strong seal for optimal flow and complete coverage. Markings on the nozzle indicate cut points for 4.5 mm, 6 mm or any size you need, making it suitable for both narrow grout lines and wider applications. The Adhesive Fix-A-Floor Repair Adhesive is strong and flexible, featuring elastomeric bonding properties that prevent future issues caused by foundation movement, expansion and contraction of the subfloor or poor original installation. Used by flooring professionals for years, this product allows any homeowner to fix loose, hollow or squeaky tiles quickly and permanently. It is non-toxic, non-flammable and eco-friendly. Whether you are repairing a small area or a large floor section, Fix-A-Floor delivers lasting results and is guaranteed for the life of your floor. Just Drill & Fill! FAQs Q: Will Fix-A-Floor work with heated floors?A: Yes. Many customers use Fix-A-Floor over heated floor elements with no issues. Turn off the heating before, during and for 48 hours after applying. Q: Some of my grout is missing. Can I still use Fix-A-Floor?A: Yes. If small gaps or cracks exist, simply Drill & Fill. The adhesive will re-bond and stabilise loose areas. If the grout is completely missing, re-grout lightly, allow it to dry and then apply Fix-A-Floor. Q: Can I repair my whole floor or just one tile?A: Fix-A-Floor works on all sizes of problem areas, from a single tile to an entire room. It is suitable for all types of tile, marble and stone floors. Q: Can I use Fix-A-Floor outside?A: Yes. It performs well in both interior and exterior applications, including patios and decks. Q: Can I use Fix-A-Floor in showers or pools?A: No. It is not recommended for areas exposed to constant or excessive moisture. Q: Is Fix-A-Floor safe?A: Yes. It is a non-toxic, non-flammable, water-based adhesive that is safe and environmentally friendly. Q: Can I use it to re-glue a tile that has come loose?A: Yes. Apply Fix-A-Floor directly to the floor where the tile was, press the tile firmly into place, apply weight and allow to cure for 24 hours. Q: Do I need to place weight on the floor after filling?A: It is recommended to place some weight, such as a heavy object or bucket, on the area to aid curing and ensure even distribution. It is not mandatory but helps achieve optimal results. Q: What if adhesive does not appear from other holes?A: The adhesive may still be spreading beneath the tile. Move to the next hole and continue filling. Make sure you are not pressing the nozzle down onto the subfloor during application.
$39.95
Repair flexible plastic items easily with Bostik Soft Plastics Glue. This clear, quick-drying adhesive creates a strong yet flexible bond that withstands stretching, bending and movement, making it perfect for repairing soft plastic and vinyl materials around the home, outdoors or on the go. Ideal for Inflatable toys, air mattresses and pool liners Vinyl upholstery, raincoats and tarps Plastic footwear, shower curtains and coated fabrics Features and Benefits Dries clear for neat, invisible repairs Flexible and waterproof once cured Strong, long-lasting bond for soft PVC and vinyl Easy to apply directly from the tube Directions Ensure surfaces are clean, dry and free from grease or dust. Apply a thin, even layer of glue to both surfaces. Press together firmly and allow to dry for 10–15 minutes. For best results, leave for 24 hours to achieve full bond strength. Clean Up Wipe away excess adhesive with a clean cloth before it sets. Once cured, mechanical removal may be required. Safety Information Use in a well-ventilated area. Avoid contact with skin and eyes. Keep out of reach of children.
$12.98
Tarzan’s Grip new formulation is a clear, flexible, general purpose solvent-based adhesive for household and hobby uses. An all-purpose glue which bonds almost everything Grabs in minutes - the exact "grab time" depends on the surfaces to be joined Fast drying Water resistant
$4.89
![Selleys No More Gaps Multipurpose Sealant Filler 150g [White]](http://gluesaustralia.com.au/cdn/shop/files/87cc1e989ee946138f896f38cf05e9d4.jpg?v=1757753073&width=645)
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 300% elongation/stretch and up to +/- 15% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage. Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application). Is formulated for long term resistance to cracking and crumbling. Easy water clean-up Will not stain building materials. Has good resistance to weathering. Low toxic, low odour, low VOC, less harmful to the environment Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles which are not exposed to water In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Paint Many other building materials
$8.00
Selleys Glass Silicone is an acetic acid curing 100% silicone, which has excellent adhesion to glass and has been specially formulated for glazing and aquarium construction. Features The acetic curing formulation results in superior adhesion on glass and glazing surfaces. Superior silicone formulation forms a durable seal and which does not shrink when drying. UV and weather resistant remaining flexible, not shrinking, crumbling, cracking or drying out. Temperature resistance – approximately -60°C +150°C Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. 25-year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Clear Appearance Smooth Where can this product be used? Windows Glass aquariums Perfect for use on or around: Windows Windows Frames Glass Aquariums Repairs gaskets in dryers, ovens, refrigerators and washing machines. Repairs rips in awnings. Will not adhere to concrete, cement products, zinc or copper containing metals, marble, limestone or lead. Can not be painted over. Not suitable for use on oily woods such as cypress, teak or cedar. Not suitable for use on roofs and gutters as it will cause corrosion. Use SELLEYS Roof and Gutter Silicone. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Stainless Steel Many plastics including polystyrene Most woods Rubber/ canvas Glazed ceramics & porcelain How to use this product Thoroughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow drying completely before applying silicone. If there is old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenious product makes removing old silicone easy. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. For aquariums, allow the product to fully cure for 7 days. Prior to usage, thoroughly wash out with water, drain and refill before introducing fish. Suitable for constructing and repairing small aquariums. The specialist design required for large tanks. Contact SELLEYS if unsure. Handy tips Tips for Using a Silicone Sealant on Glass Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. The depth of the sealant should be no more than 10mm in joints. To fill larger joints use a suitable backing rod (such as closed cell polyethylene foam or similar), leaving the gap depth no larger than half the width of the joint. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as product releases acetic acid while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of the product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$17.00
Selleys All Clear is a multi-purpose sealant that provides long-lasting protection. All Clear is the solution to water leakage and seepage around the home. Best for : Metal, Timber, Glass, Glazed tiles, Brick, Stone, Many plastics (may damage polystyrene and polycarbonate) Features Works on wet, oily, and dirty surfaces* Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Where can this product be used? Sky lights Windows frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' enteries Sealing metal or PVC guttering and down pipes Shower screens Sinks and basins Sealing leaks in caravans and recreation vehicles What materials is this product suitable for? Metal Timber Glass Glazed tiles Brick Stone Many plastics (may damage polystyrene and polycarbonate) Use only in a well-ventilated area. Avoid contact with skin and eyes and breathing vapours. The surface must be free from dust, loose particles, and soap residue. If required, clean with turps. Porous surfaces must be dry. Cut cartridge, fit nozzle, and cut to size. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. Apply with a caulking gun, forcing product into the gap. Press into cracks or surface by pushing sealant ahead of nozzle. Smooth sealant surface immediately with tool dipped in turps. Limitations: May damage some plastics e.g. polystyrene and polycarbonate. Not for permanent water immersion e.g fish tanks Not suitable for use over silicones Not suitable for polystyrene foam *Wet Surfaces: Can be applied to clean, wet non-porous surfaces e.g. metals, glass, glazed tiles – not wet porous surfaces e.g. concrete, timber. Remove as much water as possible, preferably with acetone. Keep nozzle close to surface so sealant contacts surface immediately. Flatten immediately into joints. Adhesion improves on drying. Skins immediately, maximum toughness achieved over several days. Paintable immediately with water-based paints. For oil-based paints undercoat first with a water-based paint. Store in cool dry conditions, below 30°C
$12.00
Single Shot, no mess just throw away Self piercing tube Bonds in 10 seconds Where can this product be used? Ideal for small repair jobs or when immediate results are required For interior projects and repairs Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or materials containing alkaline elements Has no gap filling properties, therefore, surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Metals China Rubber Leather Some plastics
$6.00
A rapid dual-action adhesive system is specially designed to work on plastic to form resilient, invisible bonds in seconds. Recommended on: Plastic, Porcelain, Metal, Rubber, Leather, Wood, Paper. Properties: Bonds even difficult to bond plastics such as polyethylene (PE) and polypropylene (PP) Bonds in seconds Dries transparent Easy to open, self-piercing and anti-clog cap Suitable for use on most surfaces* Solvent-free * Except Styropor®, car glass and synthetic fibres. Use: Ensure surfaces to be joined are clean, completely dry and close fitting. Using the Surface Activator like a pen apply it to both surfaces and wait 60 seconds to dry. Twist the glue cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$10.67
Selleys Auto Fix Auto Sealant Translucent 100 mL Keep water out and vibrations at bay with a clear automotive sealant that bonds fast and stays flexible. Selleys Auto Fix Auto Sealant is a 100 percent neutral cure silicone designed for cars, caravans, and general automotive sealing where a durable waterproof finish is essential. Why you will like it 100 percent neutral cure silicone Versatile general purpose sealant for automotive use Waterproof seal that resists vibration and temperature extremes UV and weather resistant for long lasting performance Skins in 5 minutes, set to touch in 30 minutes, full cure in 24 hours Where to use it Adheres to most auto and caravan materials, including: Glass and painted surfaces Fiberglass and most plastics Trim components Most rubbers Typical applications Sealing around lights, windows, and trim Gasket style sealing where a flexible waterproof joint is required General leak prevention and small gap sealing in automotive and caravan fittings Directions Preparation: Clean surfaces so they are free of dust, oil, and moisture. Wipe with mineral turpentine and allow to dry. Cut and load: Remove cap, unscrew nozzle, remove seal. Refit nozzle and cut at a 45 degree angle to the desired bead size. Apply: Squeeze the tube with steady pressure to lay a continuous bead. Smooth with a gloved finger before the sealant skins. Clean up: Before cure, clean tools and excess with mineral turpentine. Once cured, remove by cutting or scraping. After use: Replace cap. Let cured material in the nozzle be removed before next use. Handy tips Mask edges for neat joints. Remove tape before skin forms. Work within the skin time to achieve a smooth finish. Limitations Not recommended for Natural rubber, NBR, or Chloroprene Neoprene Technical details Technology 100 percent neutral cure silicone Colour Translucent Packaging Tube 100 mL Density 1.02 g per mL Application temperature -20°C to 50°C Skin time 5 minutes Shore A hardness 25 Elongation at break 370 percent Movement capability 25 percent Service temperature -40°C to 180°C VOC 26 g per L Clean up and storage Clean uncured sealant with mineral turpentine Store below 30°C in a cool dry place Use within 24 months from date of production Safety: Refer to the product SDS for handling and first aid information. Use in a well ventilated area and keep out of reach of children.
$21.55
Selleys Auto Fix Windscreen Sealant 100 mL - Black Stop leaks fast around windscreens and windows with a durable, weather resistant silicone seal. Selleys Auto Fix Windscreen Sealant forms a waterproof barrier that resists vibration, UV and temperature extremes, keeping water, dust and drafts out. Why choose this sealant 100 percent neutral cure silicone for reliable sealing Forms a waterproof seal to stop leaks quickly UV and weather resistant for long term performance Skins in 5 minutes and is touch dry in about 30 minutes Handles joint movement up to 25 percent Suitable surfaces Glass and windscreens Rubber surrounds and trims Painted surfaces and most plastics Metal frames and channels Typical applications Sealing between windscreen glass and rubber Sealing between rubber and metal frames Stopping minor water ingress around vehicle windows General sealing where a flexible, black silicone finish is desired Key specifications Technology Neutral cure silicone Colour Black Movement capability Up to 25 percent Skin time About 5 minutes Set time About 30 minutes Full cure Approximately 24 hours Service temperature -40°C to 180°C Application temperature -20°C to 50°C VOC 26 g/L Pack size 100 mL tube Directions Remove any dirt or moisture between the rubber and glass, or rubber and metal. Clean with mineral turpentine and allow to dry. Remove cap, unscrew nozzle, pierce inner seal, refit nozzle, then cut the tip at a 45 degree angle. Insert the nozzle between the rubber and glass or rubber and metal where possible. Squeeze the tube with steady pressure to push sealant into the joint. Smooth off with a gloved finger. If additional smoothing is needed, do it before the sealant skins. Clean up uncured sealant with mineral turpentine. Cured material must be cut or scraped away. Replace the cap after use. Allow sealant in the nozzle to cure, then remove before next use. Handy tips For neat lines, mask both sides of the joint and remove tape before the sealant skins. Best results occur when the joint is clean, dry and free of loose material. Limitations Not recommended on natural rubber, NBR or chloroprene neoprene due to poor adhesion. Clean up and storage Clean uncured sealant with mineral turpentine. Remove cured sealant by cutting or scraping. Store in a cool, dry place below 30°C. Use within 24 months of production. What you get 1 x Selleys Auto Fix Windscreen Sealant 100 mL - Black
$23.08
Shower Plug Penetrating Sealer 220mL Stop leaks without removing tiles. Shower Plug penetrates into masonry surfaces and forms a water repellent barrier that fixes and prevents leaks in showers, balconies and other masonry areas. One application lasts 10 years. Penetrates grout, tile and masonry to block water at the source No tile removal required Indoor and outdoor use, friction and UV resistant Does not change surface appearance or make it slippery Makes surfaces easier to clean and helps prevent mould Breathable seal allows trapped moisture below tiles to escape Seals gaps up to 1 mm. For wider cracks, repair with grout or silicone first Why Shower Plug Released in 1992, Shower Plug is the original Australian penetrating sealer technology for leaking shower repair. It delivers cost and time efficiency with proven longevity and reliability. Fixing a leaking shower, methods compared Item Tile and membrane removal and replacement Shower Plug 220mL Typical cost > $1000 $55 Time required > 5 days 30 minute application, ready to use in 12 hours Skill level Trade DIY Effective lifespan Average 5 years 10 years minimum Coverage Approx. 7 m² per pack (about 75 ft²), depending on porosity. Where to use Grout Tiles including ceramic, porcelain, marble, glazed or unglazed, terrazzo, slate, terracotta and more Concrete and masonry Bare plaster. If painting later, use a solvent primer undercoat after treatment Showers, balconies, other tiled or masonry wet areas Not suitable for Plastics and polymers such as polyurethane and polycarbonate Glass Metal Wood Painted surfaces How to apply Ensure the surface is clean and dry. Using a natural bristle brush, apply the first coat evenly. After 5 minutes, apply a second coat. Five minutes after the second coat, wipe away any remaining excess from the surface. Allow to cure. Area is ready to use in 12 hours. Important: Wipe the final coat off within 5 minutes. If left to dry on the surface, a white residue may appear. Remove any residue with turpentine. Good to know Gives off a mild solvent type odour during application and cure. This fades by the end of curing. Does not affect clothing under normal use. Safer to handle than household paint when used as directed. Always use protective gear and ventilation. Specifications SKU SP220ML Category Shower Plug Pack size 220 mL Coverage Up to 7 m² per pack Weight 0.25 kg Dimensions 7.5 cm x 7.5 cm x 8 cm Finish Invisible. No change to surface look or feel Use areas Showers, balconies, tiled and masonry wet areas Lifespan 10 years Directions recap Two coats applied 5 minutes apart. Wipe off excess 5 minutes after second coat. Ready to use in 12 hours. What you get Shower Plug 220 mL bottle Simple step by step instructions Shower Plug gives you the solution.
$61.69
Boston Liquid Thread Sealant 50g Boston Liquid Thread Sealant is an anaerobic sealant formulated to seal metal threads on gas and water pipes. It cures in the absence of air once confined between metal surfaces, creating a reliable, leak resistant seal. Why choose this sealant Seals metal threaded fittings for gas and water systems Fast handling strength in 10 to 20 minutes at room temperature Full cure in 24 hours for long lasting performance Resists vibration and helps prevent loosening Approved for gas service and type tested for contact with potable water Where to use Metal to metal threaded connections on gas lines and appliances Metal to metal threaded connections on cold and warm water pipes up to 55°C Not suitable for Plastic, glass, or rubber parts Non threaded gaps or joints exposed to air Continuous steam temperatures above 135°C Directions Remove oil and contamination from threads. Ensure parts are clean and dry. Apply sealant to one surface, covering 2 to 3 thread rotations. Assemble threads. Wipe off any excess sealant immediately. Allow 10 to 20 minutes for initial cure before pressurising. Allow 24 hours for full cure. Disassembly can be performed using standard hand tools. Good to know Anaerobic sealants cure when air is excluded between metal parts. Sealant exposed to air will not cure. Packaging is larger than contents to prevent in bottle curing. Net content is 50g. Always wipe away excess to avoid any metallic taste from uncured material in potable water systems. Apply with good ventilation. If contact occurs with eyes or skin, flush with clean water immediately. Store in a cool, dry place. Keep out of reach of children. Approvals and compliance Approved by the Australian Gas Association (Cert. No. 7583, Class III, 2000 kPa) Type Tested AS/NZS 4020 (PTT40067, SAI Global) Specifications Chemistry Anaerobic thread sealant for metal parts Pack size 50g Initial cure 10 to 20 minutes Full cure 24 hours Gas temperature range -10°C to +135°C Water temperature range Up to 55°C Pressure class Class III, up to 2000 kPa Substrates Metal to metal threads only What is included 1 x Boston Liquid Thread Sealant 50g tube.
$8.40
Selleys Sealant & Adhesive Remover 375g helps soften and lift old sealants and sticky residues so you can cleanly remove them and re-seal with confidence. The non-drip formula clings to joints and vertical surfaces, making bathroom and kitchen refreshes faster and easier. Key benefits Softens cured silicone and many common sealants to aid scraping and removal Helps break down adhesive residue, tapes and grime build-up Non-drip gel action for vertical joints, corners and trims Low mess application with excellent wetting of tight gaps Preps surfaces for fresh re-sealing and re-bonding Where to use Bathrooms: around showers, baths, basins and splashbacks Kitchens and laundries: benchtop perimeters, sinks and tiles Windows and doors: frames, trims and glazing edges Suitable substrates Glass, ceramic tiles, porcelain, enamel, stainless steel and many metals Some plastics and laminates (always test first in an inconspicuous spot) Not recommended on Natural stone, marble or porous tiles Freshly painted, delicate or lacquered surfaces Acrylic and polycarbonate sheets, mirror backings and other sensitive plastics Directions Cut away and remove as much old sealant as possible with a plastic scraper. Protect surrounding areas. Shake or stir if required, then apply a generous layer to remaining residue. Allow time for the remover to penetrate. Dwell time will vary by sealant type and thickness. Gently scrape and wipe away loosened material. Reapply if needed for stubborn spots. Wash the area with warm soapy water, rinse and dry thoroughly before re-sealing. Pro tips Score thick beads along the edges with a utility blade before application to help penetration. Work in manageable sections and avoid letting the remover dry on the surface. Always test on a small hidden area to check surface compatibility. Safety Use in a well ventilated area and wear gloves and eye protection. Avoid contact with skin and eyes. Keep out of reach of children. Product details Brand: Selleys Type: Sealant and adhesive remover Pack size: 375g
$38.69
Selleys Araldite Extra Time Epoxy Adhesive 200ml Araldite Extra Time is a strong two part epoxy that gives you an extended working time of up to 60 minutes. It is ideal for complex or multi piece assemblies where accurate positioning matters. Once cured it forms a tough, durable bond that dries translucent. Why you will love it Extended working time of 60 minutes for precise assembly Holds up to 150 kg per cm² when fully cured on clean, abraded steel Dries translucent for a neat finish Versatile bonding across common materials Suitable materials Wood, metal, masonry, china, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. Pre test on leather and rubber for suitability. Typical uses Furniture repairs and assemblies Fixing metal or timber components General household, hobby, and craft bonding Repairs on masonry, ceramics, and glass where a clear finish is preferred Directions Surface prep: abrade, clean, and dry both surfaces. Pierce each tube using the spike in the cap. Dispense equal parts onto a clean disposable surface. Mix thoroughly. Leave for 5 minutes, then mix again before applying. Mixed glue is usable for about 1 hour at 20°C. Do not use the plastic blister to mix. Apply to both surfaces and join. Support if needed to prevent movement. Avoid strain for 6 to 8 hours. Full strength develops after 24 to 72 hours depending on conditions. Replace caps on the correct tubes to avoid cross contamination. Clean up Wipe away uncured adhesive with acetone. Once cured, mechanical removal is required. Key specs Technology Two part epoxy Working time Up to 60 minutes Initial handling 6 to 8 hours Full cure 24 to 72 hours Bond strength Up to 150 kg per cm² on abraded steel when fully cured Appearance Dries translucent Temperature resistance Up to 80°C. Bond may soften above this but strength returns when temperature normalises. Pack size 200 ml Good to know Allow longer bonding times in colder weather. Product may discolor with UV exposure. Store in a cool dry place.
$66.48
Tarzan’s Grip Multi-Purpose General Adhesive 250 g is a reliable versatile contact style adhesive for crafts and household fixes chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 250 g pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Tarzan's Grip Grip for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Multi-Purpose General Adhesive 250 g has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bonding fabric, leather, and rubber General craft builds Light repairs around the home Suitable surfaces The adhesive works well on the following surface types when properly prepared: Leather and canvas Rubber trim Timber and some plastics Card and foam board Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of allow adhesive to tack before assembly as directed on pack. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Forms a tough, flexible bond after solvent evaporation and cure. Press parts together firmly for best adhesion. Temperature and environmental performance Keep away from flames and high heat during application. Once cured, it resists typical temperatures. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Use appropriate solvent on uncured adhesive, working in a ventilated space. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Replace cap after each use to reduce skinning. Store below 30 C. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$13.64
Boyle Mosaic Craft Adhesive Glue Paste 120 g is a reliable ready to use craft adhesive paste for mosaic and small decor pieces chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 120 g pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Boyle Mosaic for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Boyle Mosaic Craft Adhesive Glue Paste 120 g has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Mounting glass tesserae and small tiles to bases Decorating frames, pots, and plaques Craft classes and school projects Suitable surfaces The adhesive works well on the following surface types when properly prepared: Terracotta and ceramic bases Primed timber Card and board Glass and stone pieces Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of workable for extended craft sessions. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Initial grab holds pieces in place while you continue working. Allow to dry fully before grouting or moving finished items. Temperature and environmental performance Use in dry indoor conditions for best results. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wipe away fresh squeeze out with a damp cloth. Wash brushes in warm soapy water. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Close lid firmly after use to prevent skinning. Store at room temperature. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$7.34
Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL is a reliable two part fast setting epoxy adhesive for durable repairs chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 24 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Tarzan's Grip Grip for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Household and workshop repairs that need speed and strength Fixing fixtures, brackets, and hardware Filling chips and rebuilding small edges before sanding Suitable surfaces The adhesive works well on the following surface types when properly prepared: Metal hardware Ceramic tiles Most rigid plastics except polyethylene and polypropylene Timber and MDF Stone and concrete Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of 3 to 5 minutes working time. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Initial set is reached in about 5 minutes at 23 C. Sandable after several hours. Achieves high final strength after a full overnight cure. Temperature and environmental performance Performs well across typical domestic temperature ranges after cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured excess with acetone on a cloth. Use care on painted substrates. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed to prevent crystallisation. Store upright at moderate temperature. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$11.50
Bostik Super Glue Instant Bond gives you fast, reliable fixes for everyday repairs. Each pack includes three 1 mL single-use tubes to keep the adhesive fresh and reduce clogging, so you only open what you need. Why you’ll love it Sets in seconds for quick repairs High strength, clear finish Precise nozzle for controlled application Three single-use tubes to minimise waste Best for Metal, most plastics*, rubber, ceramic, porcelain Wood trims, leather, cork, card, paper Small household, craft, hobby and DIY fixes How to use Ensure surfaces are clean, dry and close-fitting. Lightly sand smooth or glossy areas. Pierce the tube seal, fit the nozzle and apply a tiny drop to one surface. Press parts together firmly for 10 to 60 seconds. Support if needed until handling strength is reached. Allow a few hours for maximum strength before stressing the bond. Good to know Finish: Clear Chemistry: Cyanoacrylate Viscosity: Liquid for close-fitting parts Gap fill: Very low. Parts should mate tightly. Tips Less is more. Excess can slow curing and reduce strength. Store unopened tubes upright in a cool, dry place. Use each tube once opened. For porous or flexible materials, consider a flexible or gel adhesive. Limitations Not suitable for PP, PE, PTFE, silicone, glass aquariums or very oily surfaces* Not recommended for large gaps, continuous water immersion or high heat exposure *Some plastics may require a primer. Always spot test first. Safety Bonds skin and eyes in seconds. Wear protection and keep out of reach of children. Use with adequate ventilation. If spilt on skin, do not pull; soak in warm soapy water and gently roll apart. What’s in the pack 3 x 1 mL single-use tubes of clear cyanoacrylate adhesive
$8.82
Bostik Super Glue Gel is a fast setting, non drip adhesive that stays where you put it for precise, clean bonds. The thixotropic gel formula is ideal for vertical surfaces and small gap filling, delivering reliable results on everyday repairs and crafts. Key features Fast setting gel for controlled application Non drip formula for vertical and overhead surfaces Small gap filling for close fitting parts Strong bond on many common materials Clear finish for neat repairs Ideal for Metal, rubber, most hard plastics, wood, ceramics, porcelain Small household repairs, models, craft and DIY fixes Precision bonding where liquid super glue may run Not suitable for Polyethylene, polypropylene, PTFE Very flexible materials or items regularly exposed to water immersion Food contact surfaces or aquarium use Directions Ensure surfaces are clean, dry and close fitting. Lightly roughen smooth surfaces if possible. Remove cap and apply a small bead of gel to one surface. A little goes a long way. Join parts immediately and hold firmly until set. Avoid moving the bond during curing. Allow the repair to rest for several minutes before light handling and longer for full strength. Handy tips Test on an inconspicuous area first. Use sparingly. Excess adhesive can slow cure. For porous materials, a second application may improve the bond. Clean up Wipe fresh squeeze out immediately. Once cured, carefully remove excess with a sharp blade. Adhesive may whiten on some surfaces if excess is left to cure. Storage and safety Close cap tightly after use and store upright in a cool, dry place. Bonds skin in seconds. Wear care when handling. If skin bonding occurs, do not pull apart. Soak in warm soapy water and gently roll apart. Use in a well ventilated area and keep out of reach of children.
$6.47
Bostik Hard Plastics Glue is a clear, fast-setting adhesive designed for rigid plastic repairs around the home, garage, and workshop. It forms a strong, durable bond that resists impacts and everyday handling while drying clear for a neat finish. Best for ABS, PVC, acrylic, polycarbonate, polystyrene Household repairs, toys, car trim, appliance covers Small craft fixes and model making Not suitable for Polyethylene or polypropylene PTFE or silicone surfaces Surfaces that are oily, dusty, or wet Key features Clear finish that blends with most plastics Fast initial grab with strong final cure Impact and vibration resistant Precision nozzle for controlled application Surface preparation Ensure surfaces are clean, dry, and free from dust, grease, or release agents. Lightly roughen glossy plastic with fine sandpaper to improve adhesion, then wipe clean. How to use Test on a small hidden area first. Apply a thin, even layer to one surface. Avoid excess. Join parts immediately and hold firmly for 30 to 60 seconds. Allow to set undisturbed. Handling strength is typically reached within minutes. Full cure develops over 12 to 24 hours depending on temperature and humidity. Tips For tight fitting parts, less is more. A thin film gives the strongest bond. Use clamps or tape to maintain alignment while the adhesive sets. Cleanup Wipe fresh adhesive immediately with a suitable solvent on a cloth. Cured residue may need careful mechanical removal. Storage and safety Replace cap after use and store upright in a cool, dry place. Use in a well ventilated area. Avoid skin and eye contact. Keep out of reach of children.
$12.72
Bostik Repair All is a clear, multi-purpose adhesive for quick, durable repairs around the home, garage, and workshop. It bonds strongly, remains slightly flexible, and is water resistant once cured, making it suitable for everyday fixes and craft projects. Why you will love it Strong, long lasting bond Dries clear for a neat finish Water resistant once fully cured Flexible bond helps absorb vibration Suitable for indoor and outdoor use Works on Metal, wood, ceramics, glass, most rigid plastics, rubber, leather, fabric, and more. Always test on delicate or unknown materials first. Ideal for Household repairs and DIY Craft, hobbies, and school projects Fixing ornaments, toys, trims, and fittings Directions Ensure surfaces are clean, dry, and free of dust or grease. Lightly roughen smooth surfaces. Apply a thin even layer to one surface. Join parts together and press firmly. Support or clamp if needed. Wipe away any squeeze out immediately with a cloth dampened with solvent suitable for the substrate. Allow to set undisturbed. Handling strength is typically reached within hours. Full cure is usually achieved after 24 hours depending on bead size, temperature, and humidity. Clean up Uncured adhesive can be removed with a suitable solvent. Cured adhesive is best removed mechanically by trimming or carefully scraping. Good to know Not recommended for polyethylene, polypropylene, PTFE, or surfaces that will be in constant water immersion. Avoid contact with food or drinking water surfaces. Store upright in a cool dry place with cap tightly closed. Key details Brand Bostik Product Repair All Appearance Clear when dry Finish Flexible Water Resistance Yes, once cured Pack Size 20ml Always read the label and follow safety instructions. Keep out of reach of children.
$14.50
Bring Your Leather Items Back to Life Restore your favourite leather goods such as shoes, belts, bags, and upholstery with confidence using Bostik Leather Repair Glue. This precision adhesive delivers a strong, flexible, and water-resistant bond that dries crystal clear. Key Features Ultra strong and long lasting bond for real and imitation leather Flexible and clear finish with no visible residue Resistant to water and heat up to approximately 60 °C Precision application through fine nozzle squeeze tube Multi material versatility suitable for leather, PVC, felt, canvas, some plastics, wood, and metal How to Use Ensure surfaces are clean, dry, and free from dust, oil, or old adhesive residue. For leather surfaces, avoid applying to the shiny side to prevent marks. Apply a thin film of glue to one surface. For non porous materials, apply to both surfaces. Press the surfaces together firmly. The bond sets almost instantly and reaches full strength in about 24 hours. Replace the cap immediately after use to prevent the tube from drying out. Tips and Care For best adhesion, lightly roughen smooth or shiny surfaces with fine sandpaper before gluing. Avoid stressing the repair before full cure. To remove unwanted glue, use acetone or nail polish remover on a small hidden area first. Technical Specs and Safety Form: Clear solvent based polyurethane adhesive Heat resistance: up to approximately 60 °C Highly flammable. Keep away from heat, sparks, and flame. Always follow manufacturer instructions and safety guidance. Use in a well ventilated area, wear protective gloves, and avoid contact with skin or eyes. Packaging Size: 20 mL tube
$9.79
Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load):– At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area– At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.
$21.74
Selleys Oven Plus Heavy Duty Gel is a powerful, low-fume cleaning solution formulated to remove baked-on grease and grime from ovens, cookware and bakeware. Its thick gel formula clings to vertical surfaces for deep cleaning with minimal scrubbing. Designed for warm-surface application, it delivers excellent results without harsh fumes. Surface Preparation Ensure the area is well ventilated before starting. Remove loose debris, racks, trays and oven accessories. Warm the oven slightly (no hotter than 90 °C), then turn it off and allow it to cool for 10 minutes before applying the gel. Protect surrounding surfaces such as benchtops and floors from splashes. Wear protective gloves and safety goggles when handling the product. Application Instructions Shake the tube well before use. Apply a thin, even layer of gel using the integrated brush or a dry sponge. Coat surfaces in order: back wall, sides, oven floor, ceiling, and door. Allow the gel to dwell for approximately 30 minutes. Do not let it dry out. Wipe off with a damp cloth. For stubborn spots, use a non-scratch scourer. Rinse thoroughly with water and dry before reassembling oven parts. For trays and racks, apply gel evenly, leave for 30 minutes, then rinse and dry. If cleaning carbon steel or cast iron cookware, dry and oil immediately to prevent rust. Coverage A 400 g tube typically covers a standard oven interior and racks in one application, depending on the level of buildup and thickness of application. Drying / Dwell Time Allow the product to sit for around 30 minutes. Do not exceed the recommended dwell time. Wipe and rinse thoroughly once the gel has loosened the grime. Cleanup Remove residues with a damp cloth or sponge. Rinse thoroughly with clean water to remove any remaining product. Avoid rinsing directly into drains. Dispose of waste according to local guidelines. Technical Data Form: Thick gel Colour: Clear to light blue pH: 13–14 (strongly alkaline) Density: Approximately 1.17 g/cm³ Viscosity: ~1,100 cP Water solubility: Completely miscible
$6.99 $0.02/g
Overview LOCTITE Super Glue All Plastics is a rapid dual-action adhesive kit featuring a precision super glue and a surface activator pen. Engineered to bond difficult plastics such as polyethylene (PE), polypropylene (PP) and PTFE, it forms clear, resilient bonds in seconds and resists water, most household chemicals and freezing temperatures. Ideal for repairs on toys, cameras, small automotive parts, wiper blades, rubber seals, figurines and other plastic components. Advanced bonding system: activator primes the surface; glue delivers high strength. Fuses hard-to-bond plastics: effective on PE, PP, PTFE and more. Fast & clear: sets in seconds, dries transparent for nearly invisible repairs. Durable: water-resistant and suitable for cold conditions. Surface Preparation Ensure both surfaces are clean, dry and close-fitting. Remove grease, oil, dust or loose particles. For best adhesion on very smooth plastics, lightly roughen with fine-grade sandpaper and wipe clean. Avoid use on soft foams, expanded polystyrene or highly porous materials. Always test on a small, inconspicuous area if unsure about compatibility. Application Instructions Prime with activator: Apply one or two thin coats to both bonding surfaces, ensuring full coverage. Re-cap the activator pen immediately. Allow to dry/react for 1–2 minutes. Apply adhesive: Place a minimal drop of glue on one surface only. Bring parts together immediately and hold firm pressure for at least 1 minute. Avoid shifting once contact is made. Cure: Leave undisturbed for 10 minutes. Full bond strength develops after 12–24 hours at room temperature. Coverage & Performance Only a thin film is required—one drop bonds most small mating areas. Initial handling strength is typically achieved within 5–30 seconds depending on substrates and conditions. Drying & Setting Time Initial set: 5–30 seconds* Handling time: ~1 minute Full cure: 12–24 hours Recommended conditions: 15–30 °C and ≥30% relative humidity *Setting and cure times vary with substrate, joint fit, temperature and humidity. Clean-Up & Storage Wipe nozzle to remove excess adhesive and replace caps immediately after use. Store upright in a cool, dry place away from sunlight and moisture. Do not refrigerate. Shelf life (unopened and properly stored): up to 18 months. Limitations Not recommended for glass, very flexible materials, soft foams or highly porous substrates. Not suitable for continuous water immersion or high-heat applications. For indoor use or dry environments; test before critical repairs. Safety & Handling Contains cyanoacrylate. Bonds skin and eyes in seconds. Avoid contact. Use in a well-ventilated area; consider gloves and eye protection. If skin is bonded, do not pull apart—soak in warm, soapy water and gently roll/separate. Acetone may assist on non-sensitive skin; avoid on plastics. If in eyes, rinse cautiously with water and seek medical attention immediately. Keep out of reach of children. Technical Data Product Type Two-part system: Activator + Cyanoacrylate Adhesive Substrates PE, PP, PTFE, many rigid plastics, rubber, selected metals Appearance Clear (dries transparent) Packaging Size 2 g adhesive + 4 ml activator Initial Set 5–30 seconds (substrate dependent) Full Cure 12–24 hours at ambient conditions Temperature Range Approx. −50 °C to +80 °C (typical for cured cyanoacrylates) Cleanup Mechanical removal once cured; avoid solvents on sensitive plastics What’s Included LOCTITE Super Glue (2 g) Surface Activator Pen (4 ml) Always follow on-pack directions. Performance will vary with materials, joint design and environmental conditions.
$9.64
Bostik Ultra-Strong Clear Super Glue (Liquid, Odourless, Fast-Setting) Ultra-Strong Clear Super Glue is a professional-grade, medium-viscosity liquid adhesive designed for quick, reliable repairs on most non-porous materials. It forms an instant high-strength bond that sets in seconds and reaches full cure in 24 hours. The clear, solvent-free formulation is virtually odourless for a cleaner, more comfortable user experience, and its slightly flexible bond helps resist knocks and everyday drops once cured. Why You’ll Love It Fast setting: bonds in seconds to get you back to work quickly. Ultra strong: high strength once fully cured for durable, long-lasting repairs. Water & heat resistant: engineered to stand up to common household moisture and temperature swings. Odourless & solvent-free: cleaner application with a safer, low-irritation formula. Slightly flexible bond: helps absorb minor shocks and everyday handling. Ideal Materials Best results on clean, dry, non-porous surfaces including: China, ceramics and porcelain (non-permanent on items subject to frequent washing) Rubber and elastomers Metals and metal components Jewellery repair (non-food contact) Many rigid plastics* *Not suitable for polyethylene (PE), polypropylene (PP) or PTFE (Teflon®). Not recommended for permanently bonding glass, high-alkaline materials, or items that are regularly washed. Avoid paper and other highly porous substrates. Where It Excels Quick household fixes (knobs, clips, figurines, trim) Hobby & craft assembly (non-porous parts) Workshop touch-ups and small component repair Office and general repair kits How It Works This liquid cyanoacrylate reacts with trace moisture on surfaces to polymerise rapidly, forming a high-strength thermoplastic bond. The medium viscosity helps wet out tight-fitting parts while minimising run-off when applied sparingly. Before You Start Surface prep: Ensure both surfaces are clean, dry, and free from dust, oil, rust, release agents or old adhesive. Lightly abrade glossy plastics/metal where appropriate and wipe clean. Dry fit first: Check alignment, clamping and support so parts come together quickly and accurately. Protect work area: Use disposable backing and keep caps, tissues and a small amount of acetone or nail-polish remover handy for cleanup. Application (Liquid) Open: For first use, attach/screw the nozzle and remove the cap. Apply a tiny amount: Place a small drop on one surface only. More glue can slow cure and weaken the joint. Assemble: Bring parts together immediately and hold with firm, even pressure for ~20 seconds. Avoid movement during initial set. Let it cure: Handling strength develops quickly; allow 24 hours for full cure and maximum performance. Clean-Up & Rework Fresh squeeze-out: Wipe carefully. Small residues may be treated with acetone/nail-polish remover and gently scraped once softened. On skin: Do not pull apart. Soak in warm, soapy water and gently roll/peel. Use a blunt tool (e.g., spoon handle) to separate bonded skin slowly. Pro Tips for Best Results Use the smallest effective drop—thin bondlines are stronger. Maintain close-fitting joints; gaps reduce cure speed and strength. Avoid bonding on PE, PP, PTFE and materials with heavy plasticisers or strong alkalinity. Allow the full 24-hour cure before exposing to stress, moisture or heat. Storage & Shelf Life Store tightly closed in a cool, dry place below 25 °C, away from direct sunlight. Typical shelf life: 12 months from manufacture when stored as directed. Safety Cyanoacrylate adhesive: bonds skin and eyes in seconds. Keep out of reach of children. Wear protective gloves and eye protection. In eyes: rinse immediately with water and seek medical attention. Specifications Technology Modified Ethyl Cyanoacrylate (liquid, medium viscosity) Appearance / Colour Clear Typical Working / Set Time Up to ~20 seconds (conditions and substrates affect speed) Full Cure 24 hours Water & Heat Resistance Resistant after full cure (not for continual immersion or high-temperature structural loads) Odour / Solvents Virtually odourless; solvent-free formulation Bond Character Slightly flexible; resists minor knocks and drops when fully cured Suitable Substrates China, ceramics, rubber, metal, jewellery, many rigid plastics (non-porous, clean, dry) Not Recommended PE, PP, PTFE; permanent glass bonds; high-alkaline materials; frequently washed items; paper/very porous substrates Cleanup (Uncured) Acetone or nail-polish remover; scrape gently once softened Storage Cool, dry, below 25 °C; protect from sunlight Shelf Life 12 months from manufacture (stored as directed) FAQs Can I use it on flexible rubbers? Yes, many rubbers bond well; ensure surfaces are clean and oil-free. Is it dishwasher-safe? Not recommended for items that are regularly washed, soaked or immersed. Why shouldn’t I flood the joint? Excess adhesive slows cure and weakens the bond—thin layers perform best. Disposal Allow small residues to cure fully (exposed to air) before disposal in accordance with local regulations.
$7.89
Overview This high-quality general-purpose silicone sealant is a versatile solution for a wide range of sealing and bonding applications. Engineered with neutral cure technology, it is designed to provide a durable, flexible, and weather-resistant seal that remains reliable even in demanding environments. Once cured, the sealant forms a strong rubber-like finish that is permanently elastic, ensuring long-lasting performance both indoors and outdoors. Key Features Neutral Cure Technology: Low-odor curing system suitable for sensitive applications. Permanently Flexible: Retains elasticity over time without cracking or shrinking. Waterproof Protection: Provides a watertight seal, protecting against leaks and moisture ingress. Interior & Exterior Use: Unaffected by rain, snow, extreme temperatures, or prolonged UV exposure. Excellent Adhesion: Bonds strongly to most common building materials without primer. Easy Application: Smooth flow from the tube, easy to tool and clean before curing. Applications This sealant is designed for general-purpose use across a variety of materials and environments. Its flexibility and adhesion make it suitable for: Sealing around window and door frames. Lap joints in metal guttering and roofing sheets. Bonding panels such as wood, plasterboard, insulation board, and drywall. Fixing masonry joints including sills, brickwork, and decorative trims. Gap filling around pipes, conduits, and penetration surfaces. General sealing in kitchens, bathrooms, and living areas where flexibility is required. Limitations Not suitable for permanent water immersion (e.g., underwater joints or continuous water load). Not recommended for use on polyethylene (PE), polypropylene (PP), polycarbonate (PC), polymethyl methacrylate (PMMA), PTFE, neoprene, bituminous surfaces, or very soft plastics. Not intended for deep cavity filling without adequate moisture for curing. Surface Preparation To ensure maximum performance, surfaces must be clean, dry, and free from dust, grease, or loose particles. Non-porous surfaces should be wiped with solvent and dried with a clean cloth. Porous surfaces should be lightly abraded or brushed to remove contaminants and improve adhesion. Complete any painting work before applying the sealant. Application Instructions Remove the cap and pierce the nozzle seal. Apply steadily along the joint or surface, ensuring continuous contact. Smooth or tool the bead before skin formation occurs. If masking tape is used, remove immediately after tooling to avoid tearing the cured seal. Curing At room temperature (23°C), the sealant will skin over within 15 minutes and achieve full cure within 24 hours, depending on humidity and joint depth. Once cured, it provides a permanently flexible and weatherproof joint. Cleaning & Maintenance Excess uncured sealant can be cleaned using a cloth dampened with mineral turpentine. Fully cured material should be trimmed away carefully with a sharp blade. Store unused tubes in a cool, dry place below 25°C and away from direct sunlight. Shelf life is up to 12 months from the date of manufacture. Health & Safety Use in a well-ventilated area. Avoid contact with eyes and mucous membranes, as uncured sealant may cause irritation. In case of contact with eyes, flush thoroughly with water and seek medical advice. Keep out of reach of children. Always follow safety instructions and refer to the product’s safety data for detailed guidance. Why Choose This General Purpose Silicone Sealant? This sealant is a trusted choice for tradespeople, DIY enthusiasts, and homeowners seeking a reliable solution for everyday sealing needs. Its combination of flexibility, adhesion, and weather resistance ensures that once applied, it continues to protect and bond effectively for years to come. Whether you are fixing a leaking gutter, sealing around windows, or bonding decorative trims, this product provides professional results with minimal effort. Technical Specifications Technology Neutral Cure Silicone Appearance Clear Paste Working Time Up to 15 minutes Tack-Free Time Approximately 15 minutes Full Cure at 23°C 24 hours Flexibility Permanently elastic after curing Weather Resistance Unaffected by rain, snow, UV, and temperature variations Applications Windows, doors, guttering, masonry, panels, pipes, decorative elements Storage Below 25°C, out of direct sunlight Shelf Life 12 months from manufacturing date
$9.98
Clear Flexible Fabric Glue A versatile, water-based fabric adhesive designed for clothing repairs, craft projects, and soft furnishings. It forms a strong, long-lasting, flexible bond on most porous fabrics and dries clear in thin films for a neat, professional finish. Once fully cured, the bond is machine washable, can be tumble dried, and is safe to iron. Key Features Permanent, flexible bond for clothing and crafts Water-based, low odour formula Dries clear in thin applications Machine washable and tumble-dry compatible after full cure Heat resistant—safe to iron over the bonded area Easy squeeze application; cleans up with warm soapy water while wet Ideal Uses Hems, trouser turn-ups, and pocket repairs Attaching cloth labels, badges, and patches Securing frayed lace ends and trims Curtain hems and decorative soft furnishing accents General fabric repairs on cotton, denim, linen, felt, leather and similar porous textiles Directions Preparation: Ensure surfaces are clean, dry, and free from dust or grease. At least one surface must be porous. Test first: Trial on an off-cut or hidden area, especially with light or open-weave fabrics. Apply: Spread a thin, even layer to the non-visible side or back of the fabric. Join parts and press for several seconds. Initial handling: Light handling is typically possible after about 1 minute; avoid stressing the bond. Optional set boost: For improved bonding, gently iron-press ~5 minutes after gluing (use a pressing cloth). Full cure: Reaches full effective strength after 24 hours. After curing, the item may be machine washed, tumble dried, and ironed. Clean-Up While wet: Wipe away with warm, soapy water; repeat if needed, rinse and dry. When dry on smooth, non-porous surfaces: Gently rub off or use warm, soapy water. When dry on fabrics: Difficult to remove—prevent excess and work carefully. Compatibility & Notes Best on porous textiles: cotton, denim, linen, felt, leather, and similar materials. Not suitable for non-porous materials or 100% nylon/polyester fabrics. Avoid heavy application or excessive pressure on light or open-weave fabrics to minimise show-through or darkening. Specifications Chemistry Acrylic copolymer (water-based) Appearance Milky white liquid; dries clear in thin films Density 1.07 ± 0.02 g/cm³ Solids Content 61–63% Viscosity Up to ~1,000 cps pH 4–6 Initial Handling Time ~1 minute (varies with material, temperature, humidity) Full Cure / Maximum Strength ~24 hours Washability & Heat Machine washable; tumble dry and iron once fully cured Clean-Up (Wet) Warm soapy water Pack Size 20 mL (blister) Storage Cool, dry place around 20 °C; keep container tightly closed; protect from moisture Shelf Life Up to 18 months from manufacturing date (unopened, stored as directed) Not Suitable For 100% nylon, 100% polyester, non-porous materials, very fine/delicate fabrics (e.g., some silks, wools, linens)
$13.98
Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$23.00
UHU All Purpose Adhesives Super Strong & Safe, the super strong and super fast adhesive, which is adjustable - no instant finger bonding. Suitable for virtually all flexible, solid, porous and non-porous materials. Formula patented. Withstands vibrations and tremors. Moisture and heat resistant from -50°C to +100°C. Materials Universal - glues porcelain, ceramic, many plastic materials, metal, wood, glass, leather, rubber, Styrofoam®, paper, cardboard. Not suitable for leather clothing, textiles, PE and PP. Use and Handling Instructions Surfaces to be stuck together must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. Press parts together. Glue joint remains correctable for approx. 20 seconds. The thinner the film of adhesive, the stronger the bond.
$10.74
3 x 1g originally sealed tubes ideal portion for one application. in a handy storage box reaches the smallest corners and joints Extra strong super glue in 3 x 1g tubes, packaged in a small storage box, ensuring optimal quality for every new application. The liquid adhesive reaches the smallest corners and joints. Materials Glues many plastics, porcelain, ceramic, metal, wood and rubber. Not suitable for leather clothing, PE, PP nor styrofoam. Use and Handling Instructions Surfaces to be stuck together must fit exactly and must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. The thinner the film of adhesive, the stronger the bond. Press the parts together immediately and hold in place for a short time. Breathing upon the surfaces to be stuck will speed up bonding. After use, wipe the applicator tip dry and close firmly. Will last longer if stored in a cool place.
$11.50
PROPERTIES Extra strong Fast but temporarily adjustable Does not drip Ideal for porous materials and vertical surfaces Dishwasher proof and water resistant APPLICATION SUITABLE FOR: Ideal for small-area bonds. Glues almost all solid and flexible materials like ceramics, leather, rubber, many plastics (such as rigid PVC, ABS, PS, Plexiglas®, polycarbonate (Makrolon®), and phenolic resins (Bakelite®)), porcelain, metal, wood, cork, felt, and cloth (check suitability first). Only partly suitable for glass (over a certain period of time the bond becomes brittle, causing it to weaken). Ideal for porous materials. NOT SUITABLE FOR: Not suitable for PE, PP, silicone resins, PTFE, Styrofoam®, fabrics and leather clothing. BEFORE USE: Working conditions Do not use at temperatures below +10 °C. The glue responds best to an air humidity level of 50-70 %. Surface requirements Surfaces to be glued must be clean, dry, and free of dust and grease, and must fit exactly. Preliminary surface treatment Any dust, oil, grease, wax or separating agent should be thoroughly removed from the surfaces to be stuck together. The best way to achieve this is to rub the parts a number of times with appropriate solvents, such as acetone (if suitable for the material – check first!). For metals and metal alloys it is usually sufficient to roughen the surface using emery paper or by grinding or brushing. DURING USE: Directions for use 1. To pierce the membrane, turn the cap clockwise firmly onto the tube. Tip: do not press the tube while piercing. 2. Unscrew the cap to reveal the applicator. Apply the adhesive directly from the tube, using the nozzle, as thinly as possible onto one side (too much glue slows down the curing process significantly). Press parts together immediately. After use, clean nozzle with a dry tissue and replace cap. Advice When glueing at low humidity, curing time can be shortened by briefly breathing onto one of the parts to be assembled. The best glueing results are reached at room temperature. Points of attention Contains cyanoacrylate. Bonds skin and eyelids together in seconds. If product comes into contact with the eyes, rinse immediately with plenty of water and seek medical advice. In case of contact with skin, glue can be dissolved by soaking in warm soapy water. Then apply a skin cream. May cause respiratory irritation. Avoid breathing vapours. Keep out of the reach of children. AFTER USE: Stains/residue Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue but very slowly (check suitability first). Storage conditions Store in a dry, cool, frost-free place. Storage below +5 °C (in refrigerator) ensures maximum shelf life.
$7.00
Ultra-fast and extremely strong universal super glue. Its liquid formula is easy to spread and flows into smallest corners and joints. UHU Super Glue is easy to apply, bonds quickly and provides lasting, extremely strong results. You can use it on a variety of materials so it's perfect for keeping handy in the classroom at school. You can use the glue on plastics, ceramics, wood, porcelain, metal and rubbers. It bonds quickly for fast results. The glue will flow into small corners and tight spaces. The results are extremely strong and long lasting.
$7.00
Powerful universal adhesive for most plastics. Cold welding technology for a perfect bond. Ideal for multi-purpose domestic applications, handicraft work, repairs and model building. The hard but flexible adhesive film remains transparent. Water and temperature resistant. Toluene free. YOU CAN FIX IT! Glues most usual plastic materials (ABS, Plexiglas®, hard PVC...), also in combination with wood, metal, glass and ceramics. *Not suitable for PE, PP and Styrofoam.
$12.77
A handy Super Glue pen with unique press tabs, for steady flow or drop-at-a-time application, is great to have with you at home or on the road. Great when you're looking for a precise application. Best used with non-porous application parts such as metal and rubber. The glue bonds instantly and sets in seconds! NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rearview mirrors or parts that are subjected to great shock or continuous immersion in water. Not for porous materials such as paper, fabric or foam rubber. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820C) Instructions: NOTE: For best results, surfaces should be clean & dry and parts should mate well. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Keep pen tip away from face and body. Follow directions on the card for proper opening steps. 2. Apply to one surface, using 1 drop per square inch of surface. Do not spread glue with fingers – use applicator nozzle tip. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe tip if the adhesive has accumulated before inserting a pin in the end of tube securely after use. STORAGE AND SHELF LIFE: Replace outer cap and store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause burns. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$45.00
High-Performance Future Glue® works exceptionally well with tough jobs. Surfaces do not need to be cleaned! Its powerful adhesive formula works on dirty, greasy surfaces, and resists high and low temperatures as well as most chemicals. Its instant bonding power can be used for almost all porous and non-porous materials. The medium viscosity penetrates into preassembled and close-fitting parts. Works best on Aluminum Ceramic China Corkboard Hard & Soft Wood Jewelry Leather Metal Most Plastics Porcelain Pottery Rubber Properties Initial colour Clear, transparent Final color: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -65 to 180 F (-54 to 82 C) USE INSTRUCTIONS For best results, surfaces should be clean and dry. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Carefully follow tube-opening directions on package. Unscrew cap while keeping tube pointed away from the face. 2. Apply to one surface, using 1 drop per square inch of surface. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe the top of nozzle if the adhesive has accumulated before recapping tube securely after use. STORAGE AND SHELF LIFE: Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause a burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$18.00
This new, innovative dispensing system allows for accurate control while utilizing an advanced formula of the Super Glue Corporation's signature product cyanoacrylate (Super Glue GEL). The easy to hold applicator design allows for either continuous stream or single drop control. No more sticky fingers! This glue works great when adhering to porous or vertical surfaces. It will not drip or run! Works best on: Aluminum Ceramic China Hard & Soft Wood Jewelry Metal Most Plastics Pottery Rubber Vinyl Pacer Technology AccuTool Gel (19026) is a quick-setting, non-sagging gel adhesive that fills gaps & works best on: Leather Metal Vinyl Rubber Most plastics Aluminium Ceramics Hard & Soft Wood China Pottery Jewellery Fingernails NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rearview mirrors or parts that are subjected to great shock or continuous immersion in water. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800 F (-540 to 820C) Use: For best results, items should fit closely together. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Refer to package for special opening instructions – has Self Piercing “Ratchet” Opener. After opening, remove the outer cap for use. 2. Apply sparingly to one surface using 1 drop per square inch. Assemble parts and hold together with pressure for 15 seconds or until set. 3. After use, wipe tip before replacing cap to prevent sticking and close bottle securely. Storage and Shelf Life: Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause a burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$9.95
Fix-All Adhesive is a great all-purpose solvent glue and sealer. It seals and repairs almost any surface easily and quickly. A great product for gluing wood, fabric, brick, canvas, and concrete. Also repairs tears and helps fill cracks and holes. Pacer Technology Super Glue Fix-All Adhesive (T-FA) is a single component adhesive that glues, seals and repairs and is best used for: • Metal • Plastics • Ceramics • Wood • Glass • Rubber • Fabrics • Brick • Leather • Canvas • Concrete • China • Vinyl • Porous materials • Non-Porous materials Properties: Initial colour: Clear Final colour: Clear to light yellow Open Time: 10 minutes Dry Time: 30 minutes Handling Time: 3 hours Full Strength: 24 hours Operating Temperature Range: -200 to 1500F (-290 to 660C) Instructions: Use in a well-ventilated area. Protect work surfaces. As a glue: Apply to both surfaces and let dry 10 minutes. Press parts together. Full cure in 24 hours. For rough, uneven or very porous surfaces, apply a thick layer to both surfaces and wait 30 minutes before joining parts. As a sealer: Fill crack or hole with extra amounts of Fix-All and allow to dry. Add additional adhesive as needed. For repair: To repair vinyl, rubber or fabric tears, apply Fix-All with a spatula behind, through and above the tear. Hold sides together using a strong piece of tape across the tear to hold it tightly. Remove tape after 3 hours. Remove excess with a rubber eraser. Note: when thick layers are required it is better to apply a number of thin coats. Allow curing for 3 hours before handling. Full cure in 24 hours. Notes: Solvents may evaporate from bottle or tube if left open for prolonged periods. Not recommended for Teflon, Polyethylene or Polypropylene bonding. Avoid constant submergence in water and exposure to extremely high temperatures after cure. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains xylene, naphtha and ethylbenzene. DANGER: liquid adhesive is Extremely Flammable. Harmful or fatal if swallowed. Vapour harmful. Avoid breathing vapours. Use and store in a well-ventilated area away from heat, sparks or flame. May cause eye/skin irritation. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN.
$25.00
Contact Cement is a flexible acrylic contact adhesive used to bond tile, rubber, wood, metal, formica, most plastics and much more. Pacer Technology Super Glue Contact Cement (T-CC) is a single component flexible acrylic contact adhesive that remains flexible after cure and is best used for: • Tile • Rubber • Wood • Metal • Masonite • Particle Board • Plywood • Leather • Formica • Plastic • Laminates PROPERTIES: Initial Color: Amber Dry Time: 30 minutes Final Color: Amber Full Strength: 24 hours Open Time: 10 minutes Operating Temperature Range: 15° to 150°F -9° to 66°C Instructions: Use in a well-ventilated area. 1. Surfaces should be clean and dry. For best results, use fine sandpaper to roughen the surface. 2. Apply Contact Cement to both surfaces and wait 10 minutes. 3. Press parts together. Clamp heavier parts together. Allow 30 minutes for drying time. 4. For optimum strength in all applications, wait 24 hours before using the repaired object. 5. Clean off tube or bottle top and tightly cap adhesive. Store upright and away from heat sources. Note: Solvents may evaporate from bottle or tube if left open for prolonged periods. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains methyl ethyl ketone, hexane and ethyl acetate. Warning – liquid adhesive is extremely flammable. Harmful or fatal if swallowed. Injurious to eyes with direct contact. Avoid prolonged breathing of vapours and prolonged skin contact. Wear suitable protective clothing and gloves. Use and store in a well-ventilated area away from heat, sparks or flame. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN.
$7.95
Super Glue Glass Adhesive securely attaches items to windows and mirrors. This product works well with glass beads, stemware and clear glass windows. It is water resistant, dries crystal clear, and cures after 10 minutes following direct UV exposure Works best on Glass to Ceramic Glass to Glass Glass to Metal Glass to Plastic Properties -Initial colour: Clear -Set Time: 2-5 seconds in sunlight or 150mw/cm2, 200 watt/in UV bulb @ 240-400nm or 100mw/cm2, 150 watt Halogen bulb @ 400+ nm. -Final colour: Clear -Handling Time: 10 minutes -Full Strength: 24 hours -Operating Temperature Range: -400 to 1500F (-400 to 660C) Use Instructions: Use in a well-ventilated area. Avoid direct skin contact. 1. Surfaces should be clean, dry and close fitting. Glass Adhesive will fill small gaps. 2. Wipe surfaces with nail polish remover (acetone) or rubbing alcohol (isopropanol). Allow drying at least 20 minutes. 3. Uncap the syringe. The adhesive must be shielded from UV light during application to avoid premature curing. Use adhesive sparingly, using enough to just cover one surface to be bonded. 4. Join parts, making sure that they are correctly positioned. Wipe off excess adhesive before exposure using a clean cloth with mineral spirits or acetone. 5. Expose joined parts to UV sunlight or halogen lamp. In strong sunlight, a clear bond develops in 30 seconds. For cloudy conditions, allow 1-2 minutes. Bond strength continues to develop over 24 hours. 6. Excess cured adhesive can be removed with a blade. 7. After use, wipe syringe tip and recap. Store upright. NOTE: Clear Glass Adhesive is not suitable for bonding parts exposed to oven temperatures or for deep coloured stained glass applications. Storage And Sheld Life -Store in a cool area away from sunlight or heat. Protect from freezing. Stored under these conditions, a one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS Contains Urethane acrylate oligomer, acrylate ester & acrylic acid. May cause an allergic skin reaction. Eye, skin and respiratory irritant. Use and store in a well-ventilated area. For eye contact, flush with water for 15 minutes and get medical attention. Wash skin thoroughly with soap & water after use. KEEP OUT OF REACH OF CHILDREN.
$9.95
SikaSeal®-401 Aquarium Premium one-component aquatic life safe silicone sealant SikaSeal® 401 Aquarium is a premium one-component room temperature vulcanising (RTV) silicone rubber that is safe for aquatic life and designed for sealing applications in aquariums, ponds and water pumps. It adheres very well to glass and aluminium, is UV resistant and has excellent gap filling properties. Extreme temperature resistance (-50°c to +250°c) Excellent vibration, UV and weathering resistance Good gap filling properties Usage Fish tanks Water pumps Aluminium Glass Advantages Extreme temperature resistance (-50°c to +250°c) Excellent vibration, UV and weathering resistance Good gap filling properties Highly versatile Easy to apply Aquarium safe Composition 1-C Silicone (acetoxy) Shelf life 18 months from date of production if in undamaged and unopened original sealed containers and stored according to the storage conditions. Storage conditions Must be stored in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Density ~1.02 kg/l Application Application steps SUBSTRATE PREPARATION Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue free solvent and allow to completely dry. CLEANING OF EQUIPMENT Uncured, excess SikaSeal® 401 Aquarium may be removed with Sika® Remover- 208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife. PRODUCT INFORMATION Composition 1-C Silicone (acetoxy) Packaging 75g Tube, 12 Tube per box Colour Clear Shelf life 18 months from date of production if in undamaged and unopened original sealed containers and stored according to the storage conditions. Storage conditions Must be stored in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Density ~1.02 kg/l Shore A Hardness ~23 Tensile Strength 1.0 N/mm2 Secant Tensile Modulus 1.1 n/mm2 Elongation at Break ~500% Ambient Air Temperature +5°c to +45°c Curing Rate ~3mm per 24 hours Skinning time ~7-10 minutes
$14.88
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$27.72
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$27.72
Sika MaxTack® 100g: Secure Your Projects with Unmatched Initial Grab Product Overview Sika MaxTack® 100g is a high-strength, solvent-free adhesive with incredible initial tack. Advantages High initial tack and powerful grab Secure bonding without the need for tapes, nails, or screws Excellent workability and over-paintable with water-based paints Perfect for both interior and sheltered outdoor use Applications Designed for the bonding of: Skirting boards, wood frames, and panels Anodised aluminum and hard PVC profiles Polystyrene mouldings, ceiling tiles, and more Packaging Available in 100g foil packs, 24 packs per box. Color Options Off-white in color. Application Instructions Ensure the substrate is clean and dry. For best results, follow our standard construction guidelines. Cleaning & Maintenance Clean tools immediately after use with water. Hardened material can only be removed mechanically.
$11.47
You have seen 48 out of 139 products
Compact tubes for targeted application and small repairs—great in tight spaces and for on-the-go fixes. Typical formats include gel super glues, small sealant tubes and repair compounds. Apply a thin, even film; re-cap promptly to prevent curing in the tip. Use filters to refine by chemistry, cure speed and clean-up. Always check the product page and TDS/SDS for suitability and instructions.
