Get clean, precise application of glues, epoxies, resins, oils, inks, and other liquids with this easy to use 30 ml syringe and blunt tip fill needle. Ideal for workshop, craft room, electronics bench, and on site repair jobs where accuracy matters and mess is not an option. Why you'll like it Controlled dispensing for dots, lines, seams, and small cavities 30 ml capacity for longer runs without constant refilling Graduated barrel with clear volume markings for repeatable dosing Luer lock connection keeps the needle securely attached during use Reusable barrel when used with compatible liquids and cleaned after use Blunt tip needle for safe, non piercing filling and application Common uses Injecting Fix-A-Floor through grout lines to re bond hollow or loose tiles Precision placement of two part epoxies and cyanoacrylate gels Applying PVA wood glue into tight joints and dowel holes Wicking thin adhesives along hairline cracks Filling small voids and seams before clamping Electronics work with flux, solder paste, and conformal coatings Craft, model making, leatherwork, and jewellery repairs Tile repair tip: A blunt tip of about 2 mm to 3 mm fits most grout lines. Drill a small hole in the grout as directed by the adhesive manufacturer, inject until the cavity is filled, then clean any squeeze out promptly. What is included 1 × 30 ml syringe barrel with plunger 1 × blunt tip fill needle with luer lock hub 1 × protective cap for storage Specs Capacity 30 ml Connection Luer lock Needle style Blunt tip, non piercing Barrel material Transparent polypropylene Plunger seal Latex free elastomer Use For adhesives and shop liquids only, not for medical use How to use Attach the blunt tip needle by twisting it onto the luer lock until snug. Pull back the plunger, draw in your adhesive, then tap the barrel to release trapped air. Dispense with slow, steady pressure for consistent beads and dots. For Fix-A-Floor, inject through the grout holes until filled and follow the cure steps on the product label. After use, expel remaining liquid if suitable, then flush the barrel and needle using a cleaner compatible with your adhesive. Dry completely and cap for storage. Compatibility tips Works well with PVA, polyurethane, epoxy, acrylic, latex, and many hobby liquids. For solvent based products, confirm compatibility with polypropylene before use. Do not store reactive two part mixes inside the syringe after they begin to cure. Safety Not sterile and not for medical, food, or body use. Wear gloves and eye protection when handling chemicals. Keep out of reach of children. FAQ Can I reuse itYes, if your adhesive and cleaner are compatible with polypropylene and the luer lock needle. Clean immediately after use for best results. Will it work with thick glueYes, but very thick products may require more pressure and a wider blunt tip size. Does it come sterileNo. This set is for industrial, workshop, and hobby applications only.
$18.00
![Waxstix Timber repair wax touch-up crayons [Baltic Pine]](http://gluesaustralia.com.au/cdn/shop/files/9315284510000.png?v=1754724098&width=645)
![Waxstix Timber repair wax touch-up crayons [Cedar]](http://gluesaustralia.com.au/cdn/shop/files/9315284510017.png?v=1754724098&width=645)
Colours to suit almost any timberWaxstix are so easy to use and so handy for quick repairs to scratched or damaged timber. Waxstix can be coated and stained. Plus, Waxstix contain no beeswax so they will not leave any white ring marking otherwise known as the "halo effect". For most small scratches, simply rub the stick over the damaged area. For larger, deeper indentations (where TIMBERMATE water-based Woodfiller cannot be used), heat a knife blade with a flame or a soldering iron or stove lighter and fill the damaged area with hot wax. Remove excess wax by rubbing with the smooth side of sandpaper, a piece of cardboard or an old credit card. Use a cotton cloth to buff and remove excess wax.
$7.10
Earl’s Wood Hardener - Restore Soft, Rotted Timber Like New Bring weakened, decayed timber back to life with Earl’s Wood Hardener. This water-based consolidator penetrates deep into soft, rotted fibres and bonds them into a tough, stable base that’s ready for filling, sanding, and painting. Use it to save windowsills, frames, posts, decking boards, furniture, fences, and more—without costly tear-outs or replacements. Why Customers Love It Repairs instead of replacing: Restores soft, crumbly timber to near original strength so you can patch and repaint. Water-based formulation: Low odour, no volatile organic compounds, and non-toxic when cured. Ready to use: Pre-mixed; just shake and apply—no diluting or measuring. Works inside and out: Ideal for interior and exterior timber exposed to weathering. Versatile application: Pour, brush, spray, or syringe to saturate deep into affected areas. Long shelf life: Stays usable for extended periods when stored correctly. Proudly Australian made: Developed for local conditions and everyday DIY and trade use. Where to Use Window sills and sashes, door frames, posts, fences, balustrades, fascia boards, decking edges, outdoor furniture, indoor furniture, trims, mouldings—any non-structural timber showing soft rot or fibre breakdown. How It Works The thin, penetrating formula wicks into softened timber fibres. As it cures, it binds those fibres together to form a firm, stable base that can be filled, sanded, and coated. No need to carve out all the rot—thorough saturation does the heavy lifting. Directions Prep: Ensure the area is dry. Remove dirt, dust, grease, loose paint, varnish, and flaky wood. Mask adjacent finishes if needed. Apply: Shake well. Generously pour, brush, spray, or syringe the hardener into the affected timber. Repeatedly saturate to drive product deep into fibres. Cure: Allow to cure until solid and no longer tacky to the touch. Extremely soft timber may need multiple treatments. Repair: Fill voids with a compatible wood filler, let set, then sand smooth. Finish: Prime/seal and paint or coat as desired. Pro Tip For deep penetration around a localized patch of rot, mark approximately 75 mm either side of the soft area and drill small holes between those points. Brush, spray, or syringe the hardener into the holes until saturation is achieved. Clean-Up & Safety Clean tools and drips with water while wet. Use above 7 °C and in well-ventilated areas. Non-toxic when cured. Always follow label directions and keep out of reach of children. Compatibility Once cured, the hardened substrate accepts most timber fillers and putties. After filling and sanding, it can be primed and top-coated with typical timber paints and finishes. Always test on a small area for compatibility. Limitations Not for structural load-bearing repairs. Not recommended for constant water immersion or areas that cannot be dried prior to application. Timber must be reasonably sound after consolidation; heavily degraded material may require multiple treatments or replacement. Specifications Type Water-based timber consolidant / hardener Use Restoring soft, rotted, non-structural timber prior to filling and painting Appearance Low viscosity liquid; dries clear/transparent Odour / VOC Low odour; no volatile organic compounds Application Methods Pour, brush, spray, or syringe to saturate fibres Interior / Exterior Suitable for both Minimum Application Temperature Above 7 °C Cure Indicator Ready for filling when firm and not tacky to the touch Clean-Up Water while wet Shelf Life In excess of 2 years when stored sealed in a cool, dry place Substrates Soft or rotted timber (non-structural), interior and exterior Country of Manufacture Australia Packaging Ready-to-use container What’s in the Box Earl’s Wood Hardener (ready to use) Storage Keep container tightly closed. Store upright in a cool, dry location away from freezing and direct heat. Do not allow product to dry out in the container. Disposal Allow residual product to cure before disposal. Follow local waste regulations. Important Notes Always read and follow the product label before use. Test on a discreet area to confirm adhesion and finish compatibility. The consolidated timber is not structural and should not be relied upon for load-bearing applications.
$27.95 - $179.95
The Monarch Mini Skeleton caulking gun is a smaller size caulking gun matched to the range of Monarch Mini sealant cartridges. This compact design provides easier access to tight spaces where conventional size guns find difficult. Featuring an inbuilt cartridge opener, the mini caulking gun can open a cartridge safely without using a knife for quick & easy use.
$7.07
Finish off any sealing projects with precision and accuracy using a cleverly designed caulking gun. Supporting most standard sized caulk and sealer cartridges in a sturdy steel frame, this gun is perfect for achieving smooth, clean results each and every time. Equip with a comfortable grip for controlled application, the caulking gun is ideal for any DIY aficionado producing quality professional edges, corners and joins. Durable steel frame Comfortable grip Fits most caulk and sealer cylinders Strong sturdy steel rod and quick-release system Suitable for light to medium sealant applications
$13.80
Ryobi ONE+ 18V Dual Temperature Hot Glue Gun – Tool Only delivers precise and consistent adhesive application for DIY, craft, and repair projects. Designed for versatility, it features dual temperature control and cordless convenience, making it ideal for home and professional use. Key Features Dual temperature settings: Choose between 120°C for delicate materials and 160°C for stronger bonding applications. Fast heat-up time: Ready to use in approximately 3 minutes for quick, efficient work. Long nozzle design: Provides greater reach and precision when gluing hard-to-access areas. Drip tray and ergonomic handle: Keeps your workspace clean and provides comfort during extended use. LED indicator: Red light shows warming up, green light indicates ready-to-use. Part of the Ryobi ONE+ system: Compatible with all Ryobi 18V ONE+ batteries (sold separately). Specifications Voltage: 18V High Temperature Mode: 160°C Low Temperature Mode: 120°C Glue Stick Diameter: 11–12 mm Nozzle Hole: 3.0 mm Heat-Up Time: Approx. 3 minutes Weight (without battery): 0.4 kg Included Ryobi ONE+ 18V Dual Temperature Glue Gun (Tool Only) User Manual Compatible Batteries (Sold Separately) RB18L13, RB18L15, RB18L20, RB18L25, RB18L40, RB18L50, RB18L60A, RB18L90A, and more from the Ryobi ONE+ range. Safety and Maintenance Use only original accessories and spare parts. Avoid contact with hot surfaces. Do not immerse the tool or battery in liquid. Clean using a dry cloth and store with batteries removed when not in use for extended periods. Imported by Techtronic Industries Australia Pty Ltd, Mount Waverley VIC 3149.
$118.80
Earl’s MiracleWipes – Innovative, Professional-Grade Cleaning Wipes Meet the jobsite and workshop essential that takes on the messes others can’t. MiracleWipes® are purpose-built to remove tough contaminants like oil-based paint, latex paint, epoxy, spray paint, stain, grease, oils, adhesives, ink, and grime from hands, tools, and surfaces. The unique absorbent-lock design grabs and traps residue so it doesn’t smear, while the low-solvent formula is surface and skin safe when used as directed. Dual-texture wipes (scrub on one side, smooth on the other) give you the control to lift heavy build-up then finish clean. Seeing is believing! Why You’ll Love It Removes paint & epoxy fast: Cuts through wet and semi-cured paints, epoxies, stains, grease and more. Absorb & lock technology: Traps mess in the wipe to reduce smearing and re-depositing. Dual-texture performance: Textured side agitates; smooth side finishes clean. Low solvent, professional grade: Powerful on mess, considerate on common jobsite materials. Surface & skin safe: Designed for hands, tools, and non-porous surfaces when used as directed. Large wipe size: 12" × 6" sheets give you more cleaning area per pull. Clean, no-rinse finish: Leaves no heavy, oily residue; dries quickly. Smart canister: One-at-a-time dispense with a tight snap-seal lid to keep wipes fresh. Where It Works Ideal for use on: Hands & skin: Great for cleanup after painting or epoxy work (avoid eyes, mouth, and broken skin). Tools & equipment: Brushes, rollers, spray guns, trowels, mixers, blades, scrapers. Common surfaces: Metals, coated plastics, laminates, sealed wood, glass, tiles, stone benchtops (sealed), vinyl & PVC. Prep before painting: Wipe down to remove dust, light oils, fingerprints and shop grime prior to coating. Always test on an inconspicuous area first. Not recommended for unfinished leather, delicate textiles, or uncured high-gloss finishes. How To Use Open the snap-seal lid and pull one wipe through the dispenser. Use the textured side first to loosen paint, epoxy, grease, or grime. Flip to the smooth side to lift away residue and finish clean. For stubborn spots, hold the wipe against the area briefly, then wipe again. Repeat with a fresh wipe if needed. Close the lid firmly after each use to prevent drying out. Dispose of wipes in the bin—do not flush. Pro Tips Epoxy cleanup: Tackle while epoxy is wet or green for fastest results. Surface prep: After wiping, allow to air dry, then apply coatings per product directions. Electronics & sensitive parts: Power down first; use a lightly damp section of the wipe and avoid pooling liquid. Frequently Asked Questions Will MiracleWipes remove fully cured epoxy?They excel on wet and semi-cured residues. Fully cured epoxy typically requires mechanical removal; wipes help with final cleanup. Are they safe on skin?Yes when used as directed on hands. Avoid contact with eyes and broken skin. Rinse with water after heavy use if desired. Do they leave residue before painting?The low-residue formula dries quickly. For best coating adhesion, allow the surface to dry or give a quick final wipe with a clean, dry cloth. Can I use them on automotive paint or delicate finishes?Test first in a hidden spot, especially on fresh or uncured coatings. Are the wipes flushable?No. Dispose of used wipes in general waste. What’s In The Pack Count: 90 pre-moistened, dual-texture wipes Wipe size: 12" × 6" (approx. 30.5 × 15.2 cm) Dispenser: Resealable snap-seal canister Storage & Handling Keep lid closed to prevent drying. Store upright in a cool, dry place. Keep out of reach of children. Use in a well-ventilated area. Do not ingest. Do not flush. Specifications Brand Earl’s Product MiracleWipes® – Innovative Cleaning Wipes Primary Use Removal of paint (oil & latex), epoxy, spray paint, stain, grease, oils, adhesives, inks, and grime Wipe Construction Dual-texture (scrub + smooth), high-absorbency lock design Wipe Size 12" × 6" (approx. 30.5 × 15.2 cm) Pack Size 90 wipes per canister Solvent Level Low solvent Skin/Surface Safety Surface & skin safe when used as directed Residue Low-residue, fast-dry Country of Manufacture Made in the USA Dispensing One-at-a-time pull through snap-seal lid Disposal General waste only; do not flush Suggested Applications Trade & DIY paint cleanup (rollers, brushes, sprayers, trays) Epoxy projects (boats, composites, woodwork, crafts) Auto & equipment maintenance (oils, grease, grime) Site prep and tidy between coats Workshops, garages, construction, facilities maintenance
$32.87
The UNi-PRO Real Good Scrapers are a comprehensive range of scrapers, perfect for DIY jobs such as removing flaky paint or silicone. The blades have been extremely durable and reliable in various weather conditions and over time. With the scraper being made from high quality German steel that has resistant to corrosion, your professional tool will last just as long as you do!
$5.64
Prep Indoor Furniture Wood Polish is a naturally formulated polish designed to restore, protect and beautify indoor timber surfaces. It covers light scratches, lifts stains and renews the natural richness of wood with a transparent matt finish. Uses Nourishes, restores and protects indoor furniture and woodwork Conceals minor scratches and blemishes Removes stains and dull patches Helps preserve timber surfaces from everyday wear Product Details Size / Packaging 500 mL bottle Coverage Up to 20 m² per litre Application Method Mist on and wipe in with a clean rag Number of Coats 1 coat Recoat Time After 24 hours Finish Transparent matt How to Apply Shake the bottle well before use. Mist the product lightly onto the timber surface. Wipe it in using a clean, soft rag until evenly spread. Let it cure for 24 hours before applying any further coats or placing items back. Why Choose Prep Indoor Furniture Wood Polish This polish is ideal for those seeking a gentle but effective wood restore solution for their indoor furniture. Its natural formulation ensures it is kind to timber while delivering visible results, improved colour, refreshed surface, and protection from everyday wear.
$19.95
The Mr Clean Power Dry Squeegee 355mm is a window cleaning squeegee built for a streak-free, scratch-free finish, with a wide head that clears water from large panes in fewer passes. It pairs an aluminium frame with a rubber blade, and it can be fitted to any Mr Clean extension pole so you can reach high windows from the ground.About the productMr Clean describes this squeegee as commercial grade, with professional rubber blades. The 355mm head size suits wide windows and glass doors. The frame is aluminium and plastic, finished in black, and the blade is designed to clean without scratching glass. 355mm squeegee head for wider coverage per stroke Professional rubber blade for a clean, streak-free finish Aluminium frame with plastic components Fits Mr Clean extension poles for hard-to-reach windows Cleans without scratching Where to use itIndoors: windows, glass doors, mirrors and other smooth glass panes.Outdoors: exterior windows and other smooth glass surfaces, either by hand or on an extension pole.How to use itWet the glass with your usual window cleaning solution and loosen any dirt with a washer or sponge first. Fit the squeegee to a Mr Clean extension pole if you need extra reach, or use it by hand on windows within easy reach. Draw the blade across the glass in smooth, overlapping strokes, wiping the blade clean with a cloth between passes. Finish by wiping any water left at the frame edges.Important notesKeep the rubber blade clean and free of grit, as trapped dirt can cause marks on the glass. Replace the squeegee if the rubber edge becomes nicked or worn, since a damaged edge will leave streaks. The extension pole is sold separately.Specifications Brand Mr Clean Product Power Dry Squeegee Head size 355mm Pack 1 squeegee Colour Black Material Aluminium and plastic, with rubber blade Pole compatibility Fits Mr Clean extension poles Use Windows and smooth glass surfaces, indoors and outdoors Care and storageRinse the squeegee with clean water after use and let it dry. Store it with the rubber blade clear of other tools so the edge stays straight and undamaged. Keep it out of prolonged direct sun and away from sharp objects to help the blade last.
$13.99
Replacement Sikaflex cartridge nozzles sized for large Sikaflex cartridges. Re-usable for repeat applications.Features & Benefits Pack of 3 nozzles Large Sikaflex cartridge size Re-usable Specifications Type Replacement cartridge nozzle Pack size 3 nozzles Compatibility Large Sikaflex cartridges Re-usable Yes
$3.63
Selleys Ezy Glide: The Dry Lubricant Solution for Any Surface, Anywhere No More Squeaks, No More Sticking: All-Surface Dry Lubricant Introducing Selleys Ezy Glide, a dry, non-oily lubricant that offers long-lasting lubrication while avoiding dirt and dust accumulation. Designed for a multitude of surfaces, it's your go-to for making things glide effortlessly. Key Features: Contains a dry lubricant (PTFE) Dries clear Long-lasting lubrication Does not attract dirt and dust Non-oily lubricant Applications Include: Windows Drawers Zipper Doors Locks Indoor/Outdoor Furniture Roller Door Tracks Curtain Tracks Sailboat Runners Children's Toys Sliding Glass Doors and Mirrors Suitable Materials: Wood Metal Leather Other Absorbent Surfaces How to Use: Shake the 150g aerosol can well. Hold the can approximately 80-100 mm (3-4") from the surface and spray lightly. Allow a few minutes for drying. Limitations & Tips: Ezy Glide may not be compatible with some materials like plastics, and it produces a slippery coating. Test in an inconspicuous area first and avoid over-spraying onto floors. Use the extension tube for hard-to-reach areas. Ezy Glide does not contain silicone. Avoid overspraying on fabric as it may mark the material.
$18.82
Polishes internal furniture & joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items. Also suitable for sealing and polishing slate, terracotta and stucco Coverage: Up to 40 m2 Number of Coats: 2 Recoat: 24hrs Sheen Level: Pale Satin
$15.95
Dunlop Revive & Shine Dunlop Revive & Shine is a neutral, multipurpose cleaner and maintainer that enhances the appearance of sealed floors. Designed for use on timber, vinyl, and laminate floors, this product reduces the appearance of scuffing, increases durability, and improves gloss levels. For best results, use monthly to keep your floors looking their best. Key Benefits: Cleans and maintains timber, vinyl, and laminate flooring Provides extra durability, wear resistance, and shine Increases slip resistance Reduces the appearance of scuffing Ideal for monthly maintenance Suitable For Use On: Timber, vinyl, and laminate flooring Surface Type: Floors Location: Indoor Colour & Sizes: Colour: Milky (Dries Clear) Size: 500ml Item Code: 19882 Directions for Use: Dilution: Mix 20mL of Dunlop Revive & Shine per 1L of warm water in a bucket. Cleaning: Mop the floor with the solution. Spills: For spills, hose down the area and wash with large amounts of water. Note: The use of Personal Protective Equipment is recommended during application. Dunlop Revive & Shine is perfect for keeping your timber, vinyl, and laminate floors looking like new, providing enhanced shine, durability, and slip resistance.
$21.46
Concentrated grout additive designed to increase the flexibility, strength and water resistance of cement based grouts. Davco® 4 in 1 Grout Additive is suitable for interior and exterior domestic applications. Ideal for submerged and high foot traffic areas, where a high degree of deformability is required. Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence Usage To reduce the porosity of cement based grouts To improve the compressive strength of cement based grouts To improve the flexural strength of cement-based grouts Suitable for use when grouting over fibre cement sheet floors and swimming pools or where a greater performance level / heavy duty performance is required Advantages Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence
$24.26
Swing the Bondall Silicone Remover Push Pull Scrape around corner edges to remove silicone joints. Easily access hard to get to glues with this product that is made out of durable, sharper material than other scrape products so it’s built for any project.
$8.33
The Dewalt ToughSystem 2.0 Deep Internal Tray is a contoured insert that adds an extra layer of organised storage to ToughSystem 2.0 boxes. It is supplied as a single tray, so you can fit one or more inside a compatible box and keep hand tools, accessories and fixings within easy reach.About the productThe tray is moulded in yellow plastic and shaped to follow the inside of ToughSystem 2.0 boxes, so it makes use of the available internal space. Side latches let the tray hang from the top of the box, which leaves the space below clear for larger tools. Dual-function side handles let you lift the tray out easily and also clip it to other trays.Where to use itIndoors: inside ToughSystem 2.0 boxes kept in the workshop, garage or shed, for sorting small tools and accessories.On site: inside ToughSystem 2.0 boxes on the job, or carried on its own by the side handles.How to use it Drop one or more trays into a ToughSystem 2.0 box, or hang a tray from the top using the positioning latches. Stack trays together inside the box to build a storage setup that suits your tools. Use the side handles to remove the tray, or to connect several trays so they can be carried outside the box. The manufacturer notes that you can customise the tray by adding plywood dividers. Dividers are not included. Includes one deep internal tray. The toolbox is not included. Important notesThis tray is designed for ToughSystem 2.0 boxes. Check fit before using it with other storage products. The tray has no lid and does not lock. It is rated by the manufacturer for a load of up to 8 kg, so keep heavy items in the main compartment of the box. The product is covered by a 1 year limited warranty from the manufacturer.Specifications Brand Dewalt Product ToughSystem 2.0 Internal Tray, Deep Model number DWST83408-1 Pack 1 tray Colour Yellow Material Plastic Approx. size (L x W x H) 468 x 305 x 110 mm Compartments 1 Weight capacity 8 kg Lockable No Compatibility ToughSystem 2.0 boxes Warranty 1 year limited Care and storageWipe the tray clean with a damp cloth and let it dry before packing tools away. Keep it out of prolonged direct heat and avoid overloading it. Store it inside a ToughSystem 2.0 box or stacked with other trays in a dry place.
$26.92
The Premier Blue Garage Door Weather Seal is a 5.2m replacement bottom seal made to retrofit most Steel Line garage doors. It gives a worn or missing door seal a simple, Australian-made replacement and helps keep leaves, dust and debris out of the garage.About the productThis seal is made from UV-protected PVC, so it is built to cope with the sun exposure a garage door bottom edge gets. It is supplied as a single 5.2m length, which suits wide doors and can be trimmed to match your opening. It is made in Australia by Premier Blue.Where to use itIndoors: along the bottom edge of the door, where it sits against the garage floor when the door is closed.Outdoors: the seal is exposed to the weather on the underside of the door, and the UV-protected PVC is made for this.How to use it Confirm your door is a Steel Line model before ordering, as this version is made for those doors. Remove the old seal and clean out the retainer channel so the new seal can seat properly. Fit the new seal along the full width of the door, then trim any excess length. Close the door and check the seal sits evenly along the floor with no gaps. Important notesThis listing is for the Steel Line version. Premier Blue also makes weather seals for other door brands, so check that you are buying the right one. Measure your door width before cutting. Floor surfaces that are very uneven may still leave small gaps. This is a weather seal for the bottom of the door. It is not a floor threshold seal.Specifications Brand Premier Blue Product Garage Door Weather Seal Length 5.2 m Profile size Approx. 60 mm wide x 7 mm high Material UV-protected PVC Fits Most Steel Line garage doors Origin Made in Australia Use Replacement garage door bottom seal Care and storageKeep the seal and door channel free of grit and dirt, and wipe it down with mild soapy water when needed. Store unused lengths flat or loosely coiled, out of direct sun, so the seal does not kink or distort before fitting.
$27.82
The Raven RP48 White Self Adhesive Weather Strip is a soft EPDM rubber compression seal for the gap between a door or window frame and its stop, supplied as a 5 metre coil in white. It is made for gaps of 3 to 5mm and helps reduce draughts, dust, noise and insects around the home.About the productThe strip is made from soft EPDM rubber with a self-adhesive backing, so it peels and sticks without tools or fixings. It is designed to sit in the corner between the stop and the frame, where it compresses as the door or window closes to form a snug seal. It is sold as a 5m pack (2 x 2.5m lengths), which is generally enough for an average door frame.Where to use itIndoors: around internal door frames and window frames to cut draughts, rattles and sound transfer.Outdoors: around external doors and windows to help keep out heat, cold, rain, insects and bushfire embers.It suits timber, aluminium and PVC door and window frames where there is a consistent 3 to 5mm gap.How to use it Check that your gap sits within the 3 to 5mm range. Clean the frame so it is dry, smooth and free of dust and grease. Painted surfaces should be fully cured. Cut the strip to length with scissors or a box cutter. Peel back the backing and press the strip firmly into the corner between the stop and the frame. Close the door or window to check the seal compresses evenly without being forced. Important notesSelf-adhesive seals will not stick well to oily or oil-rubbed finishes, so make sure the surface is properly prepared. The strip is designed to be applied as it comes and is not intended to be stretched. Measure your gap first, as the seal is made for 3 to 5mm gaps only.Specifications Brand Raven Product RP48 Self Adhesive Door and Window Weather Strip Model number R48W Pack 5m coil pack (2 x 2.5m) Colour White Material Soft EPDM rubber Gap size 3 to 5mm Fixing Self-adhesive Weather resistant Yes Use Doors and windows, interior and exterior Care and storageKeep the strip in its pack in a cool, dry place until you are ready to use it. Wipe the installed seal with a damp cloth to remove dust and dirt. Replace it if it becomes flattened, torn or lifts away from the frame.
$14.32
Bear General Purpose Cloth Tape is a versatile, hand-tearable white cloth tape in a compact 4.5m roll, handy for quick temporary repairs around the house, garage or workshop. It pairs a strong, flexible cloth backing with a high-strength adhesive, so it grips well and still bends around awkward shapes.About the tapeThe cloth backing gives the tape strength and flexibility. It tears cleanly by hand, so you don't need scissors or a knife for most jobs. It also follows irregular surfaces rather than lifting away from them. The adhesive is designed to grip most clean, dry surfaces.Where to use itIndoors: temporary fixes, bundling and binding items, reinforcing cartons and packaging, and general household repairs.Outdoors: short-term repairs and securing items around the yard, shed or garage.Suitable for a wide range of clean, dry surfaces. For a critical or long-term job, test the tape on a small, hidden area first.How to use itWipe the surface to remove dust, grease and moisture, and let it dry fully. Unroll the length you need and tear it by hand. Press it down firmly along its full length, smoothing out any air bubbles so the adhesive makes good contact.Important notesThis tape is intended for temporary repairs rather than permanent structural fixes. Adhesion is best on clean, dry surfaces, and may be reduced on dusty, oily, damp or crumbly surfaces. Test on delicate or painted finishes first, as the adhesive may mark or lift some coatings when removed.Specifications Brand Bear Product General Purpose Cloth Tape Size 50mm wide x 4.5m long Pack 1 roll Colour White Backing material Cloth Application Hand applied, hand tearable Use Interior and exterior SafetyUse with normal care and keep out of reach of children. Take care when using a blade or scissors to trim the tape. Store the roll in a cool, dry place away from direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$4.22
Keep your two part adhesives flowing smoothly with genuine Loctite replacement mixing nozzles. The 1826921 static mixer is designed for 50 ml dual cartridges and delivers a consistent blend for reliable bonds on every dispense. Ideal for hybrid and acrylic systems used in repair, assembly, and maintenance. Why choose these nozzles Accurate mixing: 16 internal elements help achieve a uniform mix for 1:1 and 2:1 cartridges. Precise application: tapered tip allows controlled beads and neat finishes. Time saver: ready to fit on 50 ml B style dual cartridges with a simple screw fit. Clean workflow: single use static mixers reduce mess and cross contamination. Compatibility Fits Loctite 50 ml dual cartridges and is commonly used with hybrid adhesives such as Loctite HY 4080 and Loctite HY 4090 series. Suitable for many two part acrylics and epoxies that use 50 ml B style cartridges. Typical uses Bonding metals, composites, and many plastics in workshops and production lines. Small part assembly, bracket and fixture installs, and field repairs. General maintenance where a controlled, consistent bead is required. What is in the pack 10 x Loctite static mixing nozzles, 1826921 Key specifications Cartridge size 50 ml System B style, screw fit Mix ratio 1:1 and 2:1 Mixing elements 16 Inner diameter 3.2 mm Overall length approx. 3.0 inch Tip style Tapered Use Single use How to use Purge a small amount of unmixed material from the dual cartridge until both components flow evenly. Attach the 1826921 nozzle and secure by twisting to the screw fitting. Dispense and discard the first small bead to ensure a fully mixed stream. Apply to clean, dry, and properly prepared surfaces. Good to know Change the nozzle if material cures in the tip or if flow becomes restricted. Store cartridges as directed by the adhesive manufacturer for best results. Brand: LoctiteSKU: 1826921
$28.00
Dulux Precision Maximum Strength Adhesion Primer Get a tough, reliable bond on hard to paint surfaces with Dulux Precision Maximum Strength Adhesion Primer. This water based, low odour primer works as a primer, sealer and undercoat, creating a strong foundation for acrylic or oil based topcoats on both interior and exterior projects. Why choose this primer Water based with low odour Excellent adhesion on glossy and hard to coat surfaces Suitable as primer, sealer and undercoat Interior and exterior use Fast drying: touch dry in 30 minutes, recoat in 1 to 2 hours Topcoat within 30 days for best results Ideal surfaces Tiles, high gloss enamels, varnished timber, uPVC, fiberglass, aluminium, galvanised steel, Colorbond, glass, glazed brick, laminates and previously painted glossy finishes. Key specs Finish Flat Colour White Coverage Up to 10 m² per litre per coat, depending on surface Dry time Touch dry 30 minutes Recoat time 1 to 2 hours Full strength 7 days after application VOC 30.4 g/L Application temperature Between 10°C and 32°C Clean up Water Pack sizes 1 L and 4 L How to use Prepare the surface so it is clean, dry and free of grease, wax, dust, loose paint and rust. Wash if needed and allow to dry. Stir thoroughly before and during use. Apply 1 even coat with a high quality brush, roller or spray. For very smooth surfaces 1 coat is usually sufficient. Allow 1 to 2 hours before recoating or applying the topcoat. Topcoat within 30 days. Application tips Do not tint for difficult surfaces. Thin only if necessary with a small amount of water. When using solvent based enamel topcoats, lightly sand the primer before applying the enamel. If using under products with strong solvents, let the primer dry 24 hours and test compatibility on a small area first. Where not to use Floors, benchtops or surfaces subject to standing water Below 10°C surface temperature or if conditions may drop below 10°C during drying Clean up and safety Clean tools with water and a mild detergent, then rinse. Ensure good ventilation during use. Wear eye protection and avoid skin and eye contact. Always follow label directions.
$49.88
Ozito Trigger-Flow Hot Glue Gun 10 W is a reliable compact hot melt glue gun for quick bonding and model making chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 10 W pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Ozito Trigger-Flow for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Ozito Trigger-Flow Hot Glue Gun 10 W has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Cardboard displays and craft Light repairs and cable dressing Attaching trims, felt, and fabric accents Suitable surfaces The adhesive works well on the following surface types when properly prepared: Card, paper, fabric Wood trim and plastics that tolerate hot melt Ceramic ornaments Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of open time is short, assemble parts promptly after application. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Hot melt sets as it cools, giving fast handling strength. Full strength is reached once the bead has cooled through. Temperature and environmental performance Operate in a dry area. Avoid use on heat sensitive foams that may melt. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Peel away stray strands after cooling. Protect worktops with a mat. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Unplug and allow to cool before storage. Keep glue sticks sealed from dust. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$9.10
Protite Mould Defender Anti-Fungal Paint Additive 75 mL is a reliable liquid paint additive that helps inhibit mould growth in humid areas chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 75 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Protite Mould for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Protite Mould Defender Anti-Fungal Paint Additive 75 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bathrooms and laundries Kitchens and food prep zones Rental refresh and maintenance work Suitable surfaces The adhesive works well on the following surface types when properly prepared: Walls and ceilings coated with water based paint Suitable primers as per paint maker guidance Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of Work to normal paint tray timelines. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Mix thoroughly into your chosen paint and apply as directed by that paint. Dry and recoat times follow the paint system. Temperature and environmental performance Use within the temperature window recommended for the host paint. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean rollers and brushes according to the paint manufacturer's advice. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store upright with cap tight. Do not allow to freeze or overheat. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$27.64
Key features Instant stick for quick, clean application Refill cartridge designed for the Bostik Glu Tape dispenser Neat roller action helps prevent lumps and smears Great for scrapbooking, school projects, cards, labels, and gift wrapping Transparent adhesive for a tidy finish Long length for multiple projects Best for Paper, card, photos, and lightweight craft materials Mounting, edging, and everyday office sticking jobs How to use Ensure surfaces are clean, dry, and free of dust. Open the dispenser, remove the empty cartridge, and click in the refill. Hold the roller at a slight angle and glide along the surface to apply adhesive. Press items together firmly for a secure hold. Good to know If you misplace a strip, gently lift before pressing down firmly. Store upright in a cool, dry place out of direct sunlight. Specifications Product type: Adhesive roller refill Length: 12 m Compatibility: Bostik Glu Tape dispenser Finish: Clear
$7.07
The UNi-PRO Real Good Scrapers are a comprehensive range of scrapers, perfect for DIY jobs such as removing flaky paint or silicone. The blades have been extremely durable and reliable in various weather conditions and over time. With the scraper being made from high quality German steel that has resistant to corrosion, your professional tool will last just as long as you do!
$7.20
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Grey x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1004_b7e3fa7f-b596-4427-b05e-1d6d905aafa9.jpg?v=1754716362&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Grey x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_5bffff98-306e-4768-8b68-890bdca140bb.png?v=1754716362&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black Grip x 1.5m]](http://gluesaustralia.com.au/cdn/shop/files/949_1005_f9e8bad8-cc2d-4f12-888b-f7be3932182b.jpg?v=1754716338&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black Grip x 1.5m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_75d61b67-9ac6-4739-9648-1e850e68af71.png?v=1754716338&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](http://gluesaustralia.com.au/cdn/shop/files/9315284530374_556be8c2-fd79-4d44-bfb3-029f3b567466.jpg?v=1754716329&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](http://gluesaustralia.com.au/cdn/shop/files/93152845.png?v=1754716329&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$12.94
Manufactured from special fibred paper with added tensile strength. Buffed on both sides to ensure optimum bonding and holding power. Perforated for ease of use and better adhesion. Easy to use DIY with professional results Strong bonding and holding power Self adhesive Quick results
$13.95
Polishes internal furniture & joinery that has been previously waxed or oiled Suitable for Timber, concrete, slate, terracotta and stucco All-natural ingredients Apply with a lint-free cloth Polishes internal furniture and joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items. Uses: Also suitable for sealing and polishing slate, terracotta and stucco Coverage: Up to 40m² Apply with: Lint-free cloth Number of coats: 2 Sheen level: Pale Satin
$32.95
Polishes internal furniture & joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items. Also suitable for sealing and polishing slate, terracotta and stucco Coverage: Up to 40 m2 Apply with: Lint free cloth Coats: 2 Recoat: 24 Hours Sheel Level: Pale Satin
$30.95
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$9.33
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$185.00
A blend of nut and citrus oils specially formulated to create a drying oil to maintain and rejuvenate wooden items that come into regular contact with food or water which can cause the timber to swell and dry out. Simple wipe on and wipe off application to make timber look & feel nourished. Maintain wood items that come in contact with food & water. Ideal for wooden chopping boards, serving bowls and utensils. 250mL Simple wipe on and wipe off with a rag
$16.88
The Monarch Mini Skeleton caulking gun is a smaller size caulking gun matched to the range of Monarch Mini sealant cartridges. This compact design provides easier access to tight spaces where conventional size guns find it difficult. Featuring an inbuilt cartridge opener, the mini caulking gun can open a cartridge safely without using a knife for quick & easy use. FEATURES Small, lightweight design Inbuilt cartridge opener Dripless BENEFITS Lightweight Swivel head for easy storage Comfortable design
$8.95
Small brush suitable for different purposes including painting, spreading glue, adhesive application Size: 25mm Synthetic Bristles
$3.78
Dunlop Primer & Additive is a water-based multipurpose solution that improves the bond between porous substrates and adhesives, waterproofing membranes, or screeds. It can be used as a primer before tiling or as an additive to strengthen screeds and grouts. Surface Preparation: Ensure the surface is clean, dry, and free of dust, oil, wax, paint, or other contaminants. For new concrete or screeds, allow to cure completely. Fill cracks and voids using a patching compound. Application Instructions: As a primer, dilute 1 part Dunlop Primer & Additive with 3 parts water. Apply evenly using a brush or roller. Allow it to dry for at least 30 minutes before applying adhesives or membranes. As an additive, replace part or all of the mixing water in tile adhesives or grouts to improve flexibility and adhesion. Follow the manufacturer's recommended ratios. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Allow to dry for at least 30 minutes before overcoating. Drying may vary depending on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based acrylic polymer pH: Neutral Appearance: Milky white liquid Shelf Life: 12 months (unopened in cool, dry conditions)
$66.77
• Fluoride based formula controls slipping on ceramic, mosaic and quarry tiles, terrazzo and unpainted concrete floors • Alters surface texture yet maintains the appearance of the floor • Coverage: 10sqpm per meter
$77.97
The Sutton Tools INOX Metric Jobber Drill Set is a 19 piece index set built for drilling stainless steel, covering 1.0 mm to 10.0 mm in 0.5 mm steps. It suits fabricators, maintenance workers and serious DIYers who want one organised set that handles the tough, work-hardening nature of stainless.About the productThese jobber length drills are made from M2 high speed steel (HSS), which balances strength with heat and wear resistance. Each bit has a fast spiral and a short flute for rigidity and good swarf control. The point and stepped core are shaped for clean penetration and to limit work hardening, and a Futura Nano PVD coated tip adds wear resistance. Sutton Tools states that the INOX design achieves around 70% more life in stainless steel than standard drill bits.Where to use itIndoors: workshop and maintenance drilling in stainless steel and other metal, including benchtop fabrication, fittings and brackets.Outdoors: on-site work such as drilling stainless handrails, marine style hardware and fixtures, or trade van jobs.How to use itThe set includes: 19 INOX jobber drill bits in 0.5 mm steps from 1.0 mm to 10.0 mm A compact index case that keeps every size in order Secure the workpiece and centre punch the hole position. Use a cutting or tapping fluid, run the drill at a modest speed and keep a firm, steady feed so the bit keeps cutting rather than rubbing, which causes stainless to work harden. For larger holes, step up through the sizes starting with a smaller pilot hole. Clear swarf regularly and let the bit cool if it gets hot.Important notesDesigned mainly for stainless steel and suited to general metal drilling. Use in a drill driver or drill press with a suitable chuck, and avoid side loading or forcing the bit. Return each bit to its slot after use so the set stays complete.Specifications Brand Sutton Tools Product INOX Metric Jobber Drill Set (D180SM2) Pack 19 piece set Size range 1.0 mm to 10.0 mm in 0.5 mm steps Material M2 High Speed Steel (HSS) Coating TiAlN, Futura Nano PVD coated tip Helix angle R40 Point tolerance h8 Standard DIN 338 Storage Index case Best suited to Stainless steel Care and storageWear safety glasses when drilling and keep hair and loose clothing clear of the rotating drill. Handle freshly cut metal and hot bits with care. Wipe the bits clean, return them to the index case and store the set in a dry place to protect the coating and keep the edges sharp. Keep out of reach of children.
$233.36
The Sutton Tools Viper Cobalt Metric Drill Set gives you 25 general purpose cobalt drill bits in one case, covering 1.0mm to 13.0mm in half-millimetre steps. It suits tradies and home handypeople who want a single set that copes with metal, timber and plastics, with a longer working life than the standard Viper range.About the productEach bit has a 118° split point that helps it bite cleanly and reduces wandering when you start a hole. The 5% cobalt content adds heat and wear resistance, and Sutton rates the set at up to twice the tool life of its standard Viper drills. The bits are designed for both machine drilling and hand-held drilling.Where to use itWorkshop, job site and home projects where you need a reliable range of sizes for pilot holes, fixing holes and general drilling.Suitable materials include steel, stainless steel, aluminium, brass, timber and plastics.How to use it 25 metric bits from 1.0mm to 13.0mm, in 0.5mm steps Supplied in a hard ABS case so the sizes stay organised Secure the workpiece and mark the centre of the hole before you start Use a steady speed and firm, even pressure, and back the bit out regularly to clear swarf When drilling metal, a cutting lubricant helps keep the bit cooler Important notesThis is a general purpose set. It is not intended for masonry, concrete or tile, so use a bit made for those materials instead. Return each bit to its slot after use to keep the set complete.Specifications Brand Sutton Tools Product Viper Cobalt Metric Drill Set Model number D212V3M Pack 25 piece set Size range 1.0mm to 13.0mm in 0.5mm steps Cobalt content 5% Point 118° split point Case ABS Case dimensions 204mm x 115mm x 60mm Use Machine and hand-held drilling Care and storageWear safety glasses when drilling and keep long hair and loose clothing clear of the chuck. Let bits cool before handling them, and wipe off swarf and moisture before putting them away. Store the set closed in its case in a dry spot, out of reach of children.
$366.24
The Sutton Tools Viper Cobalt Drill Set packs 19 general purpose cobalt drill bits into one case, for tradies and keen DIYers who drill a mix of metals, timber and plastics. The 5% cobalt content is aimed at standing up to heat and wear, and Sutton Tools rates the bits at up to twice the tool life of its standard Viper drills.About the productThese are jobber-style twist drills with a 118° split point that helps the bit start where you want it, with less wandering on the first contact. The cobalt content gives better heat and wear resistance than a plain high speed steel bit, which suits repeated drilling in harder materials. They work in a drill press or machine setup as well as in a hand-held drill.Where to use itIndoors: workshop and garage jobs, fabrication, furniture and cabinetry, and general repairs around the house.Outdoors: site work, fencing and framing hardware, trailers, vehicles and general maintenance.Suitable materials include steel, stainless steel, aluminium, brass, timber and plastics.How to use it Pick the bit size that suits the hole you need and fit it firmly in the chuck. Mark the spot, then start slowly so the split point can locate itself before you increase speed. Use steady, even pressure and let the bit do the cutting. Back off the speed in harder metals, and clear swarf from the hole as you go. Use cutting fluid when drilling metal to help keep the bit cool. Return each bit to its slot in the case after use so the set stays organised. Important notesThis is a general purpose set. It is not designed for masonry, concrete or tile, so use a purpose-made masonry or glass and tile bit for those. Always secure the workpiece before drilling. Check the sizes in the case against your job before you start.Specifications Brand Sutton Tools Product Viper Cobalt Drill Set Model D212V2M Pack 19 piece set in a carry case Cobalt content 5% Point 118° split point Drilling method Machine and hand-held Suitable for Steel, stainless, aluminium, brass, wood and plastics Pack dimensions 195 x 123 x 43 mm Care and storageWear safety glasses when drilling and keep hands clear of the spinning bit. Let bits cool before handling after drilling metal. Wipe off swarf and moisture, then keep the set closed in its case in a dry spot to protect the cutting edges. Keep out of reach of children.
$276.02
The DeWalt Bi-Metal Hole Saw Kit (D180005 V) is a 14 piece set that puts the most commonly needed hole sizes, two quick-change mandrels, spare parts and a carry case into one tidy kit. It suits tradies and keen DIYers who regularly cut clean, round openings for plumbing, electrical and door-lock work and want to avoid buying saws one at a time.About the productEach bi-metal hole saw has a double-tooth design that strengthens the teeth for longer life, and a sharper tooth shape that helps it cut quickly. The deep-cut body is made to get through 2-by timber in a single pass, so you can finish many jobs without flipping the work over. Thick, hardened backing plates help protect the threads from stripping, and the taller high-speed steel cutting edge is built for tougher jobs.Where to use itIndoors: pipe and cable penetrations through stud walls, joists and plywood, cutting door lock and latch holes, fitting downlights and cabinet or benchtop cut-outs.Outdoors: pipe and conduit runs through timber framing, decking and fencing, and general site and workshop drilling.Suitable materials include timber, sheet metal and plastics.What is in the kit 11 bi-metal hole saws, ranging from 3/4 in to 2-1/2 in Small quick-change mandrel and large quick-change mandrel (DW1803 and DW1810) Replacement parts set, including spare pilot point centring bits Moulded carry case with handle for storage and transport How to use itPick the saw size you need and fit it to the mandrel that suits it, then secure the mandrel in your drill chuck. Clamp the workpiece, start slowly so the pilot bit centres the cut, then increase speed and let the teeth do the work with steady, moderate pressure. Back the saw out now and then to clear chips and keep heat down, and use cutting lubricant when cutting metal. When you finish, remove the plug from the saw and return each piece to its slot in the case.Important notesThese saws are intended for wood, metal and plastics, and are not designed for masonry, concrete or tile. Use a drill in good condition with a chuck that suits the mandrel, and always check the fit of the saw on the mandrel before starting. Sizes and contents are based on the manufacturer's kit listing, so check the sizes marked on the saws when you receive them.Specifications Brand DeWalt Product Bi-Metal Hole Saw Kit Model number D180005 V Pack 14 piece kit Hole saws 11 (3/4 in to 2-1/2 in) Mandrels 2 (small and large, quick-change) Cutting edge Bi-metal, high-speed steel, double tooth Suitable for Wood, metal and plastics Case Moulded carry case Package size 240 x 180 x 75 mm Weight Approx. 1.83 kg Care and storageWear safety glasses and gloves, and clamp the work firmly before cutting. Let saws cool before handling as the teeth and the cut edge can get hot, and wipe off chips and residue after use. Keep the kit in its case in a dry place, out of reach of children.
$197.03
The Sutton Tools TCT Multi-Purpose Plumber Holesaw Set is a 12 piece kit built around tungsten carbide tipped holesaws, covering the sizes plumbers and installers reach for most, from 19mm up to 111mm. It suits trade and DIY work, and it saves you swapping between separate saws for timber, sheet materials, plastics and tiles.About the productEach holesaw has tungsten carbide tipped (TCT) teeth, designed for strong cutting performance and long wear with minimal heat build-up. Sutton Tools states that these teeth cut timber up to five times faster than conventional bi-metal holesaws. The saws cut to a depth of up to 54mm, and deep cut-outs in the body help the core come free quickly. The set comes with a quick-release arbor, so you can change holesaw sizes fast and eject the core in about a second. Two pilot bits and a plastic storage case are included.Where to use itIndoors: pipe and fitting penetrations through timber framing, wall linings, cabinetry, benchtops and tiled walls or floors.Outdoors: openings in fibre cement and cement sheet cladding, decking and timber structures for pipework and installations.Suitable materials include timber, hardwood, softwood, MDF, plasterboard, compressed fibre cement sheet, cement sheet, plastics, ceramic tiles and other abrasive materials.How to use it Fit the holesaw to the quick-release arbor and secure the arbor in your drill chuck. Use a pilot bit to start the hole accurately, and clamp or hold the workpiece firmly. Cut with steady pressure and let the teeth do the work. Pull back occasionally to clear dust and swarf. Use the quick-release action to eject the core, then swap to another size when needed. Important notesThe cutting depth is up to 54mm, so deeper material needs to be cut from both sides. These holesaws are designed for the materials listed above. The set is not intended for cutting sheet metal or steel. Check that your drill suits the arbor and the size of saw you are using. Mid-size holesaws are listed as 51mm and 64mm in some Sutton Tools catalogue material and as 57mm and 70mm in other places, so check the pack when you receive it if you need a specific size.Specifications Brand Sutton Tools Product TCT Multi-Purpose Plumber Holesaw Set Model number H127MP7 Pack 12 piece set (9 holesaws, quick-release arbor, 2 pilot bits) Size range 19mm to 111mm Cutting teeth Tungsten carbide tipped (TCT) Cutting depth Up to 54mm Arbor H122-Series quick-release arbor Storage Plastic storage case Use Trade and DIY Care and storageWear safety glasses and hearing protection when drilling, and keep hands clear of the rotating saw. Let hot saws cool before handling. Brush off dust and swarf after use, and return the holesaws, arbor and pilot bits to the case so the teeth stay protected. Store the case in a dry place away from moisture.
$268.57
The Sutton Tools H127 Carpenter Set is an eight-piece tungsten carbide tipped holesaw kit built for builders, installers and keen DIYers who need a good spread of sizes in one case. It covers everything from small cable and dowel holes through to large pipe and fitting holes, and the carbide teeth are designed to stay sharp and run cooler than conventional bi-metal holesaws.About the productEach holesaw has tungsten carbide tipped (TCT) teeth for strong cutting performance, long wear life and minimal heat build up. Sutton Tools states that the teeth cut timber up to five times faster than conventional bi-metal holesaws. Deep cut-outs in the saw body help the plug of waste material (the core) release quickly. The quick-release arbor lets you change saw sizes fast and also helps push the core out, so you spend more time cutting and less time swapping and clearing. The International Thread Pattern means the saws also fit standard arbors.What is included 8 x TCT multi-purpose holesaws: 19mm, 22mm, 25mm, 32mm, 38mm, 54mm, 92mm and 102mm 1 x H122-Series quick-change arbor 2 x TCT pilot drill bits 1 x plastic storage case Where to use itIndoors: fitting door hardware and locks, running cables and pipework through frames and joinery, cutting holes in cabinets, shelving and panelling, and downlight or vent openings in plasterboard.Outdoors: decking, fencing, framing and sheeting work where you need clean holes for fixings, conduit or pipes.Suited to cutting timber, hardwood, softwood, MDF, plasterboard, compressed fibre cement sheet, cement sheet, plastics, ceramic tiles and other abrasive materials, to a cutting depth of 54mm.How to use itFit the saw you need to the quick-release arbor, then install the arbor in your drill chuck with a pilot bit centred. Clamp or secure the workpiece, mark the centre of the hole and start at a moderate speed so the teeth bite cleanly. Let the saw do the work rather than forcing it, and back out now and then to clear dust and swarf on deeper cuts. When the cut is through, use the quick-release arbor to free the core and swap to the next size.Important notesMatch drill speed to the material, with slower speeds for harder or more abrasive materials such as tile and fibre cement. Cutting depth is up to 54mm, so very thick material will need to be cut from both sides. Use a drill with enough torque for the larger 92mm and 102mm saws, and hold it firmly with both hands.Specifications Brand Sutton Tools Product H127-Series TCT Multi-Purpose Carpenter Holesaw Set Model H127MP6 Pack 8 holesaws, arbor, 2 pilot bits and case Holesaw sizes 19, 22, 25, 32, 38, 54, 92 and 102mm Teeth Tungsten carbide tipped (TCT) Cutting depth 54mm Arbor H122-Series quick-release Thread International Thread Pattern, fits standard arbors Use Trade, construction, installation and DIY Care and storageWear safety glasses and hearing protection, and a dust mask when cutting plasterboard, fibre cement or tile. Keep hands clear of the saw while it is spinning, and let the teeth cool before handling. Clear dust from the saws after use and return them to the case. Store in a dry place and keep out of reach of children.
$275.16
The Sutton Tools Viper Cobalt Starter Holesaw Set is a 7-piece bi-metal kit covering hole sizes from 20mm to 54mm, put together for tradies, maintenance crews and keen DIYers who want a practical base set in one case. It suits both hand and machine drilling and is built to cut through steel, stainless steel, cast iron, non-ferrous metals, plastic and wood.About the productThe cutting edge is made from bi-metal cobalt high speed steel (HSS), a combination chosen for toughness and a longer working life. The teeth are varied in pitch, which helps reduce vibration while cutting, giving a cleaner finish and better accuracy. Cutting depth is 32mm. The set has been updated with new components based on customer demand and comes in a sturdier, space-saving case that is easy to keep in the toolbox or van.Where to use itIndoors: cutting holes for cable and conduit runs, pipe and fitting cut-outs, and general maintenance and fit-out work in metal, plastic and timber.Outdoors: site and workshop jobs where you need round openings in steel sections, sheet metal, plastic or timber.Suitable materials include mild and stainless steel, cast iron, non-ferrous metals such as aluminium, plastic and timber.How to use it Fit the holesaw to a suitable arbor and pilot drill, then secure the workpiece so it cannot spin or shift. Start at a moderate speed, let the pilot drill locate, then apply steady, even pressure and let the teeth do the cutting. When cutting metal, apply cutting fluid. Sutton Tools recommends its Venom Lubricating Fluid to help extend the life of the tool. Back the saw out regularly to clear swarf and keep the teeth cool, then remove the core once the hole is through. Important notesSlow the speed down for harder materials such as stainless steel and cast iron, and keep the saw cool for the best tooth life. This is a bi-metal set for metal, plastic and timber work, and is not intended for masonry, tile or concrete. Please check the arbor and pilot drill requirements for your drill before use.Specifications Brand Sutton Tools Product Viper Cobalt Bi-Metal Starter Holesaw Set Model number H130S070540 Pack 7 piece set Size range 20mm to 54mm Material Bi-metal cobalt HSS Cutting depth 32mm Tooth design Varied pitch Case size (approx.) 260mm W x 77mm H x 158mm D Use Machine or hand drilling Care and storageWear safety glasses and gloves when drilling, and keep hair and loose clothing clear of the rotating tool. Metal cores and swarf can be hot and sharp, so let them cool before handling. Clean off debris after use, keep the teeth dry and return the saws to the case so they stay protected. Store in a dry place and keep out of reach of children.
$114.22
The DeWalt 120pc Screwdriver Bit Set packs a wide mix of driver bits, a few drill bits, nut setters and a magnetic holder into one connectable ToughCase, so most everyday fastening jobs are covered from a single case. It suits tradies and home DIYers who want one organised set instead of loose bits scattered through the toolbox.About the productThe bits are part of DeWalt's Max Fit range, which is made to work with the DeWalt power tool system. Each tip is precision machined to sit snugly in the screw head recess, which helps cut down on stripped screws. The ToughCase storage system lets you link other compatible DeWalt sets to it, building a tidy, site-ready storage stack.What is in the set 25mm bits: Pozidriv (POS7), Phillips (PH1, PH2, PH3), slotted (SL8), square (SQ1, SQ2), Torx (T20, T25), security Torx (T10, T15, T20, T25, T27, T30, T40) and hex bits (1/16", 5/64", 3/32", 7/64", 1/8", 3/16", 1/4") 51mm bits: PH1, PH2, PH3, SQ1, SQ2, T20, T25, SL6, SL8, POS5, POS7 89mm bits: PH1, PH2, SL8, T25 152mm bits: PH2, T25 Black and gold HSS drill bits: 3/32", 1/8", 5/32", 3/16", 1/4" Nut setters: 1/4" and 5/16" 1 x compact magnetic bit holder 3/8" socket adapter ToughCase storage case How to use itPick the bit that matches the screw head, push it fully into the chuck or magnetic bit holder of your drill or driver, and apply firm, straight pressure while driving. Use the longer bits for recessed fasteners and the shorter ones for general work. The socket adapter and nut setters let you drive hex-head fasteners, and the drill bits handle pilot holes. Return each bit to its slot in the case after use so the set stays complete.Important notesMatch the bit type and size to the fastener, and keep the bit square to the screw to avoid damaging the head or the tip. Check the tool and fastener ratings before using the bits with high-torque tools. Contents are listed by bit type and length, so check the pack for the exact layout.Specifications Brand DeWalt Product 120pc Screwdriver Bit Set Model number DWAF120PCSET Pack 120 piece set Case Included (ToughCase storage system) Bit lengths 25mm, 51mm, 89mm, 152mm Drill bits Black and gold HSS, 3/32" to 1/4" Approx. product size 430 x 230 x 60 mm Care and storageKeep the bits in their case slots when not in use and store the case in a dry place to help prevent rust. Wipe off dust and swarf before putting bits away, and replace any bit that shows a worn or rounded tip. Wear safety glasses when drilling or driving and keep out of reach of children.
$103.18
Diablo 32mm Universal Fit Bi-Metal Multi-Tool Blades are made for clean, fast plunge and flush cuts in timber, supplied here as a handy pack of three. They suit most oscillating multi-tools without an adapter, so one set covers a wide range of brands.About the productThese bi-metal blades are built specifically for clean wood, meaning timber without embedded nails or screws. The cutting edge is ultra-hardened, and Diablo says it lasts up to 5 times longer than standard blades. A curved contact edge helps the blade locate for precise plunge cuts with less vibration. The Japanese-style tooth pattern is designed for quick, tidy cutting. Black I.C.E. (Industrial Cooling Element) coated teeth help manage heat and clear chips so the teeth stay free of build-up.Where to use itIndoors: trimming door jambs and architraves, flush-cutting timber, notching and making plunge cuts in timber panels and framing.Outdoors: cutting decking boards, fence timber and other garden woodwork.Suitable for clean timber. For wood that may contain nails or screws, or for metal, choose a blade made for that job.How to use it Check that your oscillating multi-tool takes universal fit blades (not Starlock), then fit the blade following your tool's instructions. Secure the workpiece and mark your cut line. Start the tool before the blade touches the timber, then let the blade do the work with light, steady pressure. Use the curved contact edge to start plunge cuts accurately. Switch off and let the tool stop completely before removing or changing the blade. Important notesThis is a universal fit blade and is not compatible with Starlock tools. It is designed to work with cordless and corded oscillating multi-tools from brands such as Bosch, Craftsman, Dewalt, Dremel, Fein, Hart, Makita, Milwaukee, Porter-Cable, Ridgid and Rockwell. Check your tool's blade fitting before ordering if you are unsure. Hitting nails or screws will quickly dull or damage a bi-metal blade.Specifications Brand Diablo Product Universal Fit Bi-Metal Multi-Tool Blades for Clean Wood Model number 2610068593 Pack 3 blades Blade width 32mm Blade type Bi-metal Tooth design Japanese tooth Coating Black I.C.E. Interface Universal fit, adapter-free (not Starlock) Application Clean wood Care and storageWear safety glasses and a dust mask when cutting, and keep hands clear of the blade. Blades can be hot straight after use, so let them cool before handling. Keep out of reach of children and store the blades in their pack in a dry place to protect the cutting edge.
$82.38
You have seen 48 out of 307 products
Primers, activators, mixing nozzles, applicators and kits that complete your bonding or sealing system. Improve adhesion, speed and accuracy for pro‑quality results. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
