A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$26.95
Say Goodbye to Stubborn, Sticky Messes! Tired of wrestling with stubborn price tags that tear and leave a papery, sticky mess? Frustrated by gummy residue left behind by tape on new appliances or furniture? We've all been there, risking our fingernails and damaging surfaces trying to scrape and scrub away unwanted adhesives. It’s time to stop the struggle. Introducing Un-Du® Adhesive Remover, the ultimate solution from Glues Australia that works like magic. This isn't just another solvent; it's a revolutionary removal system. Unlike harsh chemicals that dissolve glue and ruin your items, the Un-Du® formula cleverly works by temporarily neutralizing the adhesive. A few drops are all it takes to seep under the label or sticker, breaking the bond with the surface. Simply lift it off cleanly and effortlessly with the handy included scraper tool. The best part? Once the fast-evaporating Un-Du® formula disappears, the stickiness on the sticker returns, allowing you to reuse it somewhere else! It’s the perfect tool for repositioning labels, photos, and more. An Essential Tool for Every Australian Home From the kitchen to the garage, you'll find hundreds of uses for Un-Du®. It’s the one tool that’s more versatile than duct tape, designed to solve all those sticky problems that pop up in daily life. Keep a bottle handy and you'll always be prepared. Gift Giving Made Easy: Effortlessly removes price stickers from delicate gifts like crystal vases, books, and photo frames without leaving a trace. Clean Up Your Car: Finally get rid of that old bumper sticker from your ute or the remnants of a parking permit on your windscreen without damaging the paint or glass. Appliance & Furniture Rescue: Safely removes warranty stickers, energy rating labels, and masking tape from new fridges, TVs, and fine wood furniture. Household Accidents: Lifts chewing gum from carpet, tar from floors, and crayon marks from walls with remarkable ease. The Ultimate Office & Warehouse Productivity Hack Streamline your workflow and maintain a clean, professional workspace. Un-Du® is an indispensable asset for any office, mailroom, or warehouse environment, saving you time, money, and frustration. Package & Mail Management: Open self-sealing envelopes and padded mailers without tearing them, perfect for retrieving contents or reusing packaging. File & Asset Organisation: Easily remove and replace labels on files, shelves, computer disks, and office equipment without leaving a sticky, dirt-collecting residue. Mistake Correction: Quickly lifts correction fluid (White Out) from documents without smudging or tearing the paper. Workspace Maintenance: Removes old tape marks from desks, partitions, and windows, keeping your office looking pristine. A Must-Have for Crafters and Memory Keepers Your precious memories and delicate projects deserve the best care. The Un-Du® formula is completely acid-free and photo-safe, making it the trusted choice for hobbyists, scrapbookers, and archivists who demand perfection and preservation. Scrapbooking Perfection: Safely lift and reposition photos in albums and scrapbooks without causing fading, yellowing, or damage. Model Making: Remove masking tape from delicate models without lifting paint or leaving residue. Paper Crafts: Adjust stickers and embellishments on acid-free and lignin-free papers with total confidence. Stop struggling and start un-sticking the clean, simple, and safe way. Add Un-Du® Adhesive & Sticker Remover to your cart today and discover a world free from sticky situations! Product Specifications Brand: Un-Du® Product Name: Adhesive & Sticker Remover Formula: Acid-Free, Photo-Safe, Quick-Evaporating Solvent Key Feature: Temporarily neutralizes adhesives, allowing for the reuse of most stickers and labels after evaporation. Residue: Leaves no oily, greasy, or sticky residue behind. Tool: Comes with an attached, non-scratching, integrated scraper tool for easy lifting. Common Applications: Sticker & Label Removal Tape & Decal Removal Price Tag Removal Gum & Tar Cleaning Correction Fluid (White Out) Lifting Opening Sealed Envelopes Safe For Use On Surfaces Including: Glass & Plastics Fine Wood Furniture Metals Carpets & Upholstery Delicate Fabrics Photos Acid & Lignin-Free Papers Painted Surfaces & Wallpaper And much more!
$21.68
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 58-11 Anaerobic Thread Sealant Loxeal 58-11 is a high performance anaerobic sealant designed for metal thread joints only. It replaces PTFE tape and cord, delivers instant sealing against moderate pressure, and cures to form a shock and vibration resistant seal that remains reliable from -55°C to +150°C. Why choose Loxeal 58-11 Instant sealing against moderate pressure to get systems back in service fast. Thixotropic formulation stays where you put it and resists migration on threads. Wide chemical compatibility including gas, water, LPG, hydrocarbons, oils and more. Shock and vibration resistant for durable, leak free joints. Temperature range from -55°C to +150°C for tough Australian conditions. Certified and approved Gas approvals: DVGW and DIN EN 751-1, plus Australian Gas Association for working pressure up to 20 bar. Oxygen service: Approved for gaseous oxygen up to 10 bar at +60°C. Potable water: WRAS listed and suitable for contact with wholesome water. Also approved for contact with drinking water by Global Mark. Food area use: NSF registered category S4 for use as an adhesive in and around food processing areas. Hydrogen: Tested by KIWA as a sealant for use with pure hydrogen to EN 751-1. Typical applications Sealing tapered and parallel metal threaded fittings in plumbing, HVAC, gas and hydraulic systems. Replacing PTFE tape or thread cord on metal pipework where a permanent, pressure resistant seal is needed. Directions Clean and degrease threads thoroughly. Cut the nozzle to the required bead size. Apply a continuous bead 1 to 2 threads back from the leading edge. Ensure full coverage around the circumference. Assemble and tighten the joint. Wipe away excess uncured material. Allow to cure (see Cure times). Cure speed can be accelerated on passive metals or at low temperature with an appropriate activator. Cure times at +25°C Handling: 15 to 30 minutes Functional: 1 to 3 hours Time to water service for potable water systems at +21.1°C Brass, copper, cast iron: 24 hours Stainless steel, aluminium: 7 days Technical data Chemistry Anaerobic methacrylate Colour Yellow (fluorescent under blue light) Viscosity at +25°C 20,000 to 80,000 mPa·s, thixotropic Specific gravity Approx. 1.1 g/ml Gap filling Up to 0.30 mm (M56 / 2 inch) Flash point Greater than +100°C Shear strength 6 to 13 N/mm² (ISO 10123) Breakaway torque 18 to 24 N·m (ISO 10964) Prevailing torque 7 to 14 N·m (ISO 10964) Service temperature -55°C to +150°C Shelf life 1 year in unopened packaging at ? +25°C Chemical resistance Excellent resistance to motor oil, gearbox oil, gasoline and hydraulic oil. Excellent to good resistance in 50 percent water glycol at elevated temperature. Limitations and notes For metal to metal threaded joints only. Not suitable for plastic threads or rubber components. Liquid product can attack some coatings and plastics. Pre test if unsure. For disassembly, use normal tools. Heat components to approximately +150°C to +250°C if required, then remove cured residue mechanically and clean with solvent. Store in a cool, dry place at or below +25°C. Do not return unused product to the bottle. All technical information is provided as a guide only. Always verify suitability with your specific materials, operating pressures and local regulations before use. Follow all safety and handling instructions on the product label and safety data sheet.
$19.31
Premium one component room temperature vulcanising silicone sealant USE Fridge and freezer sealing Pizza oven sealing Oven sealing Aluminium Glass CHARACTERISTICS AND ADVANTAGES High temperature resistance (-50 to 250OC) Excellent adhesion Gap filling properties Heat proof Vibration resistant Highly versatile PACKAGING: 300 ml cartridges COLOUR: Black SikaSeal® Appliance Silicone Sealant is a premium one component room temperature vulcanising (RTV) silicone rubber designed for flexible gasketing and sealing applications. SikaSeal® Appliance Silicone Sealant forms a tough but flexible seal of all shapes and sizes and fills any surface voids. The cured product can withstand vibration, weathering, temperature extremes, water oil and grease without hardening, shrinking or cracking. Uses Fridge and freezer sealing Pizza oven sealing Oven sealing Aluminium Glass Characteristics / Advantages High temperature resistance (-50 - 250°C) Excellent adhesion Heat proof Gap Filling properties Vibration resistant Highly versatile Product Data Colour Black Packaging 300ml Cartridge, 12 cartridges per box Storage 18 months from date of production if stored in undamaged and unopened original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base 1-C silicone Density (uncured) 1.0 kg/l approx. Skin Time 10 min approx. Tack-free time 20 min approx. Curing Time 24 hours approx. Cure Mechanism Moisture-curing Cure Type Acetoxy Application temperature 5 - 45°C Mechanical/Physical Properties Tensile Strength 1.0 N/mm2 approx. Shore a Hardness 25 approx. Ultimate Elongation 600% approx. Application Details Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue-free solvent and allowing drying properly. Cut the nozzle at a 45° angle to the desired bead size (3 mm is suitable for most applications) then apply a continuous and even bead along the joint. Cure Mechanism SikaSeal® Appliance cures by reaction with atmospheric moisture. The reaction thus starts at the surface and proceeds to the core of the joint. The curing speed depends on the relative humidity, temperature and thickness of the sealant. At low temperatures, the water content of the air is lower and the curing reaction proceeds more slowly. Clean Up Uncured, excess SikaSeal® Appliance may be removed with Sika® Remover-208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife. Application Conditions/ Limitations Restrictions On Use SikaSeal® Appliance is not recommended for use in applications where it will be permanently exposed to temperatures exceeding 250°C or in contact with fuels. The above information is offered for general guidance only.
$24.26
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$25.54
PC-Fahrenheit™ Putty Epoxy is the choice for temperatures up to 260° C. It is supplied as a premeasured stick that you mix with fingers. Fast curing (60 min). Best for steam heat applications. A toolbox must. Great on copper and iron. Here are just a few specific uses (there are hundreds of other uses): Seal cracked steam or hot water radiator Stop leaking steam fittings Fill hole in heat exchanger Attach thermocouple to hot surface Seal chimney ductwork How to prepare a surface for bonding with PC-Fahrenheit™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Fahrenheit™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Fahrenheit™ repair a leaking steam radiator? PC-Fahrenheit™ resists higher temperatures and is suitable for repairing steam pipes and radiators. Can PC-Fahrenheit™ be used in a fireplace or wood burning stove? PC-Fahrenheit™ will withstand temperatures up to 260°C. A fireplace or wood burning stove creates temperatures exceeding 260°C. Can PC-Fahrenheit™ be used to seal heater chimney duct? PC-Fahrenheit™ is excellent for use on sheet metal and the temperature is within an acceptable range. Can PC-Fahrenheit™ seal a rust hole in barbecue grill? PC-Fahrenheit™ can be used on the barbecue grill exterior but is not recommended for the interior. How long should PC-Fahrenheit™ be mixed before applying? Mix PC-Fahrenheit™ for 45 to 60 seconds then immediately apply. What is the temperature limit? PC-Fahrenheit is not intended to exceed 260°C. - Will PC-Fahrenheit™ burn? PC-Fahrenheit™ is not flame resistant and may burn if exposed to direct flame. Does PC-Fahrenheit™ stick to car radiator? Car radiators are made of various metals and plastic composites. Test for adhesion and test for leaks.
$16.17
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 32m x 48mm [Black]](http://gluesaustralia.com.au/cdn/shop/files/052427600356N_25b0d34f-62b0-49f4-86cb-a6535eeabdae.jpg?v=1754712481&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$27.91
Selleys Auto Fix Auto Sealant Translucent 100 mL Keep water out and vibrations at bay with a clear automotive sealant that bonds fast and stays flexible. Selleys Auto Fix Auto Sealant is a 100 percent neutral cure silicone designed for cars, caravans, and general automotive sealing where a durable waterproof finish is essential. Why you will like it 100 percent neutral cure silicone Versatile general purpose sealant for automotive use Waterproof seal that resists vibration and temperature extremes UV and weather resistant for long lasting performance Skins in 5 minutes, set to touch in 30 minutes, full cure in 24 hours Where to use it Adheres to most auto and caravan materials, including: Glass and painted surfaces Fiberglass and most plastics Trim components Most rubbers Typical applications Sealing around lights, windows, and trim Gasket style sealing where a flexible waterproof joint is required General leak prevention and small gap sealing in automotive and caravan fittings Directions Preparation: Clean surfaces so they are free of dust, oil, and moisture. Wipe with mineral turpentine and allow to dry. Cut and load: Remove cap, unscrew nozzle, remove seal. Refit nozzle and cut at a 45 degree angle to the desired bead size. Apply: Squeeze the tube with steady pressure to lay a continuous bead. Smooth with a gloved finger before the sealant skins. Clean up: Before cure, clean tools and excess with mineral turpentine. Once cured, remove by cutting or scraping. After use: Replace cap. Let cured material in the nozzle be removed before next use. Handy tips Mask edges for neat joints. Remove tape before skin forms. Work within the skin time to achieve a smooth finish. Limitations Not recommended for Natural rubber, NBR, or Chloroprene Neoprene Technical details Technology 100 percent neutral cure silicone Colour Translucent Packaging Tube 100 mL Density 1.02 g per mL Application temperature -20°C to 50°C Skin time 5 minutes Shore A hardness 25 Elongation at break 370 percent Movement capability 25 percent Service temperature -40°C to 180°C VOC 26 g per L Clean up and storage Clean uncured sealant with mineral turpentine Store below 30°C in a cool dry place Use within 24 months from date of production Safety: Refer to the product SDS for handling and first aid information. Use in a well ventilated area and keep out of reach of children.
$22.57
Overview LOCTITE Super Glue All Plastics is a rapid dual-action adhesive kit featuring a precision super glue and a surface activator pen. Engineered to bond difficult plastics such as polyethylene (PE), polypropylene (PP) and PTFE, it forms clear, resilient bonds in seconds and resists water, most household chemicals and freezing temperatures. Ideal for repairs on toys, cameras, small automotive parts, wiper blades, rubber seals, figurines and other plastic components. Advanced bonding system: activator primes the surface; glue delivers high strength. Fuses hard-to-bond plastics: effective on PE, PP, PTFE and more. Fast & clear: sets in seconds, dries transparent for nearly invisible repairs. Durable: water-resistant and suitable for cold conditions. Surface Preparation Ensure both surfaces are clean, dry and close-fitting. Remove grease, oil, dust or loose particles. For best adhesion on very smooth plastics, lightly roughen with fine-grade sandpaper and wipe clean. Avoid use on soft foams, expanded polystyrene or highly porous materials. Always test on a small, inconspicuous area if unsure about compatibility. Application Instructions Prime with activator: Apply one or two thin coats to both bonding surfaces, ensuring full coverage. Re-cap the activator pen immediately. Allow to dry/react for 1–2 minutes. Apply adhesive: Place a minimal drop of glue on one surface only. Bring parts together immediately and hold firm pressure for at least 1 minute. Avoid shifting once contact is made. Cure: Leave undisturbed for 10 minutes. Full bond strength develops after 12–24 hours at room temperature. Coverage & Performance Only a thin film is required—one drop bonds most small mating areas. Initial handling strength is typically achieved within 5–30 seconds depending on substrates and conditions. Drying & Setting Time Initial set: 5–30 seconds* Handling time: ~1 minute Full cure: 12–24 hours Recommended conditions: 15–30 °C and ≥30% relative humidity *Setting and cure times vary with substrate, joint fit, temperature and humidity. Clean-Up & Storage Wipe nozzle to remove excess adhesive and replace caps immediately after use. Store upright in a cool, dry place away from sunlight and moisture. Do not refrigerate. Shelf life (unopened and properly stored): up to 18 months. Limitations Not recommended for glass, very flexible materials, soft foams or highly porous substrates. Not suitable for continuous water immersion or high-heat applications. For indoor use or dry environments; test before critical repairs. Safety & Handling Contains cyanoacrylate. Bonds skin and eyes in seconds. Avoid contact. Use in a well-ventilated area; consider gloves and eye protection. If skin is bonded, do not pull apart—soak in warm, soapy water and gently roll/separate. Acetone may assist on non-sensitive skin; avoid on plastics. If in eyes, rinse cautiously with water and seek medical attention immediately. Keep out of reach of children. Technical Data Product Type Two-part system: Activator + Cyanoacrylate Adhesive Substrates PE, PP, PTFE, many rigid plastics, rubber, selected metals Appearance Clear (dries transparent) Packaging Size 2 g adhesive + 4 ml activator Initial Set 5–30 seconds (substrate dependent) Full Cure 12–24 hours at ambient conditions Temperature Range Approx. −50 °C to +80 °C (typical for cured cyanoacrylates) Cleanup Mechanical removal once cured; avoid solvents on sensitive plastics What’s Included LOCTITE Super Glue (2 g) Surface Activator Pen (4 ml) Always follow on-pack directions. Performance will vary with materials, joint design and environmental conditions.
$11.56
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](http://gluesaustralia.com.au/cdn/shop/files/075353964668N_2b5bb515-b170-4a54-a924-8fcf58683e02.jpg?v=1754716416&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](http://gluesaustralia.com.au/cdn/shop/files/04007_14cbee25-54b9-43ad-a832-e4231871625b.jpg?v=1754716416&width=645)
Experience unmatched strength and durability with our T-Rex Ferociously Strong Tape, now available at Glues Australia. Measuring 9.14 meters in length, this tape is specifically designed to withstand the toughest situations and most demanding projects. Crafted for homeowners, craftsmen, and outdoor enthusiasts, T-Rex® Tape distinguishes itself from ordinary duct tapes with its formidable holding power. This makes it your go-to solution for enduring repairs, creative DIY projects, or any challenging task you encounter. The secret to its exceptional performance lies in its aggressive double-thick adhesive. This feature allows the tape to adhere firmly to rough, dirty surfaces in all types of weather and temperature conditions. T-Rex® Tape is more than just a tool; it's a reliable partner for both home use and professional job sites. It outlasts and outperforms regular duct tape, ensuring that your projects, big or small, are held together longer and stronger. Key Features: All-Weather Capabilities: Equipped with a waterproof backing, T-Rex® Tape stands resilient against harsh weather elements, even in the coldest temperatures. This feature makes it an ideal choice for outdoor repairs and applications. Enhanced Durability: The tape boasts a high-tensile woven scrim, contributing to its strength and long-lasting nature. Whether it’s used for heavy-duty tasks or simple fixes, the tape’s robust construction ensures it won’t give in. Superior Holding Power: With its double-thick adhesive, T-Rex® Tape grips onto rough and uneven surfaces with unparalleled strength. This makes it perfect for tasks that require a strong, reliable hold. Versatile Usage: Suitable for both indoor and outdoor environments, the tape is manufactured using UV-resistant materials. These materials prevent the tape’s adhesive from weakening under harsh UV rays, extending its lifespan. Wide Application Range: T-Rex® Tape is versatile enough to be used on a variety of surfaces, including brick, concrete, shingles, both painted and non-painted wood, and vinyl siding. This makes it a must-have in any toolbox. Heavy-Duty Construction: Made with a heavy-duty knit cloth, the tape is designed for long-lasting repairs or applications. Whether it's for a temporary fix or a permanent solution, you can count on its reliability. Usage Applications: Home repairs, including fixing broken items and sealing leaks. Crafting and DIY projects, offering creative flexibility. Outdoor applications, including camping gear repairs. Professional job site tasks, providing reliability and strength. Why Choose T-Rex® Tape? When you choose T-Rex® Tape, you're not just selecting a tape; you're choosing a commitment to excellence and reliability. Its unique composition allows it to withstand challenges that ordinary tapes can't handle. Whether you're a professional tradesperson or a DIY enthusiast, T-Rex® Tape is the perfect addition to your toolkit, providing a strong, durable solution for any project. In conclusion, T-Rex® Tape is not just tape; it's a symbol of strength, resilience, and versatility. Its all-weather, UV-resistant features, combined with its superior adhesive strength, make it an indispensable product for anyone who values quality and reliability in their tools. Available now at Glues Australia – your trusted source for high-quality adhesive solutions.
$16.48
![Sika Sikaflex 252 High Strength Structural Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/7612895456188_c10ea96d-b0be-41ba-a0ee-9656fab35b16.jpg?v=1754711652&width=645)
Elastic adhesive for vehicle assembly bonding Sikaflex®-252 is an elastic 1-component polyurethane adhesive especially designed for bonding large components in vehicle assembly. It is suitable for bonding coated metal, GRP, ceramic materials and plastics. Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties PRODUCT BENEFITS Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties Can be painted Vibration-damping Electrically non-conductive Usage Sikaflex®-252 is suitable for assemblies that are subject to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminum (including anodized components), sheet steel (including phosphated, chromated and galvanized components), metal primers and paint coatings (2-component systems), ceramic materials and plastics. Seek manufacturer’s advice before using on plastics that are prone to stress cracking. This product is suitable for professional experienced users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
$53.62
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524002800_e901daee-d941-4c51-bb2c-fdfedd9a6316.jpg?v=1754711662&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$31.92
LOCTITE 263 is designed for the permanent locking and sealing of threaded fasteners. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. It's particularly suited for heavy duty applications such as studs into motor housings, nuts onto studs in pump housings and other fasteners where high strength is required. LOCTITE 263 provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids. Recommended on High strength Locks studs against vibration loosening Controlled/torque tension Prevents thread corrosion Fast curing How to use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole. For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours. Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush. For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 4. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 5. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 6. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 7. Assemble and tighten as required For Disassembly 1. Apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush
$18.13
Threadlocking Adhesive - medium strength. General purpose. Suitable for all metal threaded assemblies. LOCTITE® 243 is a general purpose threadlocker of medium bond strength. This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration. The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces. It is proven to be tolerant of minor contamination due to industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids. Prevents loosening on vibrating assemblies, e.g. pumps, gearboxes or presses. Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces). Proven to tolerate minor contamination by industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids Permits disassembly with hand tools for servicing Technology: Acrylic Chemical Type: Dimethacrylate ester Appearance (uncured) Blue liquidLMS Fluorescence Positive under UV lightLMS Components One component - requires no mixing Viscosity Medium, thixotropic Cure Anaerobic Secondary Cure Activator Application Threadlocking Strength Medium LOCTITE® 243™ is designed for the locking and sealing of threaded fasteners which require normal disassembly with standard hand toolsThe product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature of LOCTITE® 243™ reduces the migration of liquid product after application to the substrateLOCTITE® 243™ provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Safety Data Sheet (SDS). Where aqueous washing systems are used to clean the surfaces before bonding, it is important to check for compatibility of the washing solution with the adhesive. In some cases, these aqueous washes can affect the cure and performance of the adhesive. This product is not normally recommended for use on plastics (particularly thermoplastic materials where stress cracking of the plastic could result). Users are recommended to confirm the compatibility of the product with such substrates. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. Shake the product thoroughly before use 4. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 5. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 6. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 7. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 8. Assemble and tighten as required For Disassembly 1. Remove with standard hand tools 2. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot 3. Apply localized heat to the assembly to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush
$18.07
Introducing Gorilla Clear Grip® - Your Ultimate Adhesive Solution! Are you tired of struggling with weak bonds that don't stand the test of time? Say goodbye to ordinary adhesives and embrace the power of Gorilla Clear Grip® - the flexible, fast-setting, and crystal clear contact adhesive that creates an unbreakable bond! Unleash your creativity with Gorilla Clear Grip®! Whether you're building, repairing, or crafting, this heavy-duty adhesive is your go-to companion. Its no-run formula ensures a clean and easy application, while the fast grab feature holds your project in place within seconds, saving you precious time and effort. Worried about the unpredictable weather? Fear not! Gorilla Clear Grip® is fully waterproof, making it ideal for both indoor and outdoor projects. Rain or shine, your creations will stay intact and look flawless for years to come. What sets Gorilla Clear Grip® apart is its remarkable versatility. It forms a permanent bond on a wide range of materials, including metal, glass, fabric, wood, ceramic, leather, paper, plastic, and more. With Gorilla Clear Grip®, you can confidently tackle any project, big or small. Concerned about safety? Worry not! Gorilla Clear Grip® is photo-safe and washer/dryer safe, ensuring that your precious memories and fabrics remain unharmed during the bonding process. Using Gorilla Clear Grip® is a breeze! Just ensure that the surfaces are clean and apply the adhesive to each surface to be bonded. For maximum bond strength, wait a couple of minutes for the adhesive to partially dry before joining the surfaces. The bond forms immediately, ensuring a strong connection. Store your Gorilla Clear Grip® in a cool, dry location after each use, away from children and animals. The flammable adhesive requires extra care, so keep it away from heat, sparks, flames, or smoking. For easy re-opening, apply a thin coat of petroleum jelly to the threads before replacing the cap. Frequently Asked Questions: Q: What surfaces does Gorilla Clear Grip® adhere to? A: Gorilla Clear Grip® adheres to a wide variety of surfaces, including wood, metal, stone, ceramic, glass, plastic, PVC, brick, concrete, foam, paper, rubber, fabric, and laminate. However, it is not recommended for use on polystyrene, polypropylene, or polyethylene products, and it should not be used around food. Q: How do you clean up Gorilla Clear Grip®? A: To clean uncured adhesive, wipe it with a dry cloth and then use acetone, isopropyl alcohol, or citrus-based solvents according to the manufacturer's instructions. Cured adhesive can be removed by scraping it from the surface. Q: Is Gorilla Clear Grip® UV resistant? A: Yes, it is UV resistant, making it ideal for outdoor applications. Experience the Gorilla Clear Grip® difference today! Unleash your creativity, achieve impeccable results, and make your projects stand the test of time. Join the countless satisfied customers who have discovered the power of Gorilla Clear Grip®. Build, Repair, Craft™ with confidence!
$20.51
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 9.1m x 48mm [White]](http://gluesaustralia.com.au/cdn/shop/files/052427601001N_6bf5df2b-2379-4b95-849b-de69b5185a52.jpg?v=1754712477&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$14.99
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 27.4m x 48mm [White]](http://gluesaustralia.com.au/cdn/shop/files/052427840585N_07d2cff7-275f-4461-91ba-a3bace52b8c5.jpg?v=1754712482&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$29.62
Meet your go to epoxy putty for fast, permanent style repairs. Gorilla All Purpose Epoxy Stick is a hand mixable putty that sets in about 10 minutes and cures in 24 hours to a tough, machinable finish. Once cured it can be drilled, sanded, and painted. It is waterproof, non rusting, and ready for indoor or outdoor jobs around the home, car, boat, and garden. Why you will like it Fast setting. Approximate set time 10 minutes. Paintable after about 1 hour. Full cure in about 24 hours for a hard wearing repair. Works on most common materials including metal, PVC, many rigid plastics, wood, stone, ceramic, brick, concrete, fiberglass, and glass. Non rusting formulation for durable repairs in wet or humid areas. Waterproof when cured. Suitable for indoor and outdoor use. NSF ANSI 61 certified drinking water safe for contact with potable water once cured. Great for Plumbing repairs such as sealing low pressure leaks and patching drainage pipes Automotive trims and general panels that do not exceed service temperature of typical epoxy repairs Household fixes like filling holes, anchoring hardware, rebuilding small parts, and edge repairs DIY and craft projects that need a sculptable, sandable fill Important use notes Not for exhaust systems. For plumbing, use for temporary repair of drainage pipes or low pressure pipes only. Turn water off, apply, then wait at least 1 hour before turning water back on. Bonded wood should not be submerged or soaked after repair. How to use Wear disposable gloves. Work in a well ventilated area. Prepare the surface. Clean off dust, oil, and loose material. Roughen smooth surfaces with sandpaper. Cut the amount you need. Remove the film wrapper and foil sticker. Reseal unused putty to limit air exposure. Knead for 30 to 60 seconds until the colour is uniform. Mix thoroughly or it will not harden completely. Apply within 5 minutes of mixing. Press firmly into place. Smooth with wet gloved fingers if a smooth finish is desired. Remove any squeeze out before hardening. Allow to set about 10 minutes. Paint after about 1 hour. Full cure about 24 hours. Specifications Format Hand mixable epoxy putty stick Size 56.7 g Set time About 10 minutes Paintable After about 1 hour Full cure About 24 hours Indoor or outdoor Yes, waterproof when cured Drill, sand, paint after cure Yes Drinking water contact NSF ANSI 61 certified drinking water safe once cured Clean up and storage While uncured, wipe away with soap and water, acetone, or isopropyl alcohol. For cured material, remove by sanding, scraping, or chiseling. Store the stick in its vial with film and foil sticker re applied. Keep sealed in a cool, dry place. Keep away from children and animals. Safety Wear gloves during mixing and application. Avoid contact with skin and eyes. If in eyes rinse with water for 15 minutes. If on skin wash with soap and water. Use in a well ventilated area. For medical emergencies in Australia call 000.
$17.90
Gorilla Tough & Clear Mounting Tape is a clear double-sided tape that mounts in an instant, for a long-lasting, weatherproof bond. The crystal clear adhesive tape won’t yellow over time, and holds up to 6.8kg! (15 pounds) Gorilla Tough & Clear Mounting Tape is perfect for indoor and outdoor projects and sticks to smooth and rough surfaces. Completing DIY projects is easy with this tough, double-sided tape. Mount, build, and repair for a perfect finish, every time. Features 6.8KG Strong Hold - Sticks to smooth and rough surfaces.* Weatherproof - For indoor and outdoor use. Crystal Clear Adhesive - Won't yellow over time. Double Sided Tape - coated with adhesive on both sides for easy hanging. Bonds - Plastic, Metal, Wood, Glass, Brick, Ceramic, Stone & More! *weight limits may vary depending on surface texture, porosity and flatness of surface. Both surfaces must be completely flat to make full contact with adhesive. Is Gorilla Mounting Tape permanent? Yes. Once Gorilla Mounting Tape is used to mount an object, it is meant to be held in place permanently, and not be removed. How much weight will Gorilla Mounting Tape hold? Gorilla Black Mounting Tape will hold up to 30 (13.6KG) pounds per project. How do I remove Gorilla Mounting Tape’s liner? Once Gorilla Mounting Tape is pressed onto the surface of the object to be held, remove the liner by peeling it from a corner of the tape. This can be done by using a fingernail or similar object to separate the liner from the tape. How do I remove Gorilla Mounting Tape? Gorilla Mounting Tape is a permanent tape. Once applied, it can be difficult to remove, and can damage surfaces if the objects are pulled away from the surface. If Gorilla Mounting Tape isn’t exposed and cannot be reached by hand between the mounted object and the surface, a prying motion on the object from one corner can sometimes remove it from the surface. Please note that damage to the surface can occur. If Gorilla Mounting Tape is exposed and within reach between the mounted object and the surface, pull the tape parallel to the surface (or vertically downwards) to remove it from the object. How much Gorilla Mounting Tape should I use on my project? Use four inches of Gorilla Heavy Duty Mounting Tape per pound of weight being held.
$17.95
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/9310492265001_6fb5fccc-7784-41bb-9997-bbd917e3c834.png?v=1754712704&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$22.51
Boston Liquid Thread Sealant 50g Boston Liquid Thread Sealant is an anaerobic sealant formulated to seal metal threads on gas and water pipes. It cures in the absence of air once confined between metal surfaces, creating a reliable, leak resistant seal. Why choose this sealant Seals metal threaded fittings for gas and water systems Fast handling strength in 10 to 20 minutes at room temperature Full cure in 24 hours for long lasting performance Resists vibration and helps prevent loosening Approved for gas service and type tested for contact with potable water Where to use Metal to metal threaded connections on gas lines and appliances Metal to metal threaded connections on cold and warm water pipes up to 55°C Not suitable for Plastic, glass, or rubber parts Non threaded gaps or joints exposed to air Continuous steam temperatures above 135°C Directions Remove oil and contamination from threads. Ensure parts are clean and dry. Apply sealant to one surface, covering 2 to 3 thread rotations. Assemble threads. Wipe off any excess sealant immediately. Allow 10 to 20 minutes for initial cure before pressurising. Allow 24 hours for full cure. Disassembly can be performed using standard hand tools. Good to know Anaerobic sealants cure when air is excluded between metal parts. Sealant exposed to air will not cure. Packaging is larger than contents to prevent in bottle curing. Net content is 50g. Always wipe away excess to avoid any metallic taste from uncured material in potable water systems. Apply with good ventilation. If contact occurs with eyes or skin, flush with clean water immediately. Store in a cool, dry place. Keep out of reach of children. Approvals and compliance Approved by the Australian Gas Association (Cert. No. 7583, Class III, 2000 kPa) Type Tested AS/NZS 4020 (PTT40067, SAI Global) Specifications Chemistry Anaerobic thread sealant for metal parts Pack size 50g Initial cure 10 to 20 minutes Full cure 24 hours Gas temperature range -10°C to +135°C Water temperature range Up to 55°C Pressure class Class III, up to 2000 kPa Substrates Metal to metal threads only What is included 1 x Boston Liquid Thread Sealant 50g tube.
$8.40
Sikaflex 258 Primerless Glass Adhesive 310 mL is a reliable polyurethane glass adhesive designed for primerless bonding to suitable automotive glass chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 310 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Sikaflex 258 for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Sikaflex 258 Primerless Glass Adhesive 310 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bonding glass where a primerless system is specified Automotive and transport glazing carried out by trained users Suitable surfaces The adhesive works well on the following surface types when properly prepared: Compatible glass substrates Painted frames and prepared bodywork per Sika guidance Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of observe skin time and install components within this window. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Moisture cure technology forms a strong, elastic bond. Skin forms first, followed by through cure depending on joint depth and humidity. Temperature and environmental performance Do not apply below the minimum stated on pack. Maintain adequate humidity for moisture cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Remove fresh adhesive with suitable cleaner. Once cured, trim with a sharp blade using care. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store cartridges cool and dry. Check use by dates before installation in critical work. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$37.49
Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL is a reliable two part fast setting epoxy adhesive for durable repairs chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 24 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Tarzan's Grip Grip for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Household and workshop repairs that need speed and strength Fixing fixtures, brackets, and hardware Filling chips and rebuilding small edges before sanding Suitable surfaces The adhesive works well on the following surface types when properly prepared: Metal hardware Ceramic tiles Most rigid plastics except polyethylene and polypropylene Timber and MDF Stone and concrete Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of 3 to 5 minutes working time. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Initial set is reached in about 5 minutes at 23 C. Sandable after several hours. Achieves high final strength after a full overnight cure. Temperature and environmental performance Performs well across typical domestic temperature ranges after cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured excess with acetone on a cloth. Use care on painted substrates. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed to prevent crystallisation. Store upright at moderate temperature. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$13.14
Bostik Hard Plastics Glue is a clear, fast-setting adhesive designed for rigid plastic repairs around the home, garage, and workshop. It forms a strong, durable bond that resists impacts and everyday handling while drying clear for a neat finish. Best for ABS, PVC, acrylic, polycarbonate, polystyrene Household repairs, toys, car trim, appliance covers Small craft fixes and model making Not suitable for Polyethylene or polypropylene PTFE or silicone surfaces Surfaces that are oily, dusty, or wet Key features Clear finish that blends with most plastics Fast initial grab with strong final cure Impact and vibration resistant Precision nozzle for controlled application Surface preparation Ensure surfaces are clean, dry, and free from dust, grease, or release agents. Lightly roughen glossy plastic with fine sandpaper to improve adhesion, then wipe clean. How to use Test on a small hidden area first. Apply a thin, even layer to one surface. Avoid excess. Join parts immediately and hold firmly for 30 to 60 seconds. Allow to set undisturbed. Handling strength is typically reached within minutes. Full cure develops over 12 to 24 hours depending on temperature and humidity. Tips For tight fitting parts, less is more. A thin film gives the strongest bond. Use clamps or tape to maintain alignment while the adhesive sets. Cleanup Wipe fresh adhesive immediately with a suitable solvent on a cloth. Cured residue may need careful mechanical removal. Storage and safety Replace cap after use and store upright in a cool, dry place. Use in a well ventilated area. Avoid skin and eye contact. Keep out of reach of children.
$12.72
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Grey x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1004_b7e3fa7f-b596-4427-b05e-1d6d905aafa9.jpg?v=1754716362&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Grey x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_5bffff98-306e-4768-8b68-890bdca140bb.png?v=1754716362&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black Grip x 1.5m]](http://gluesaustralia.com.au/cdn/shop/files/949_1005_f9e8bad8-cc2d-4f12-888b-f7be3932182b.jpg?v=1754716338&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black Grip x 1.5m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_75d61b67-9ac6-4739-9648-1e850e68af71.png?v=1754716338&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$27.72
SikaTitan® 258 is a primerless to windscreen, one-component direct glazing adhesive. It is easy to apply and has a paste-like consistency. On exposure to atmospheric moisture it cures to a durable elastomer. SikaTitan® -258 provides a long tack-free time and ensures a safe application even under warm conditions. Note: Primerless application requires the glass to be prepared with a non-antistatic glass cleaner. Also the bonding surfaces must be free of contamination prior to the application of the adhesive. SikaTitan® -258 is manufactured in accordance with ISO 9001 / 14001 quality assurance system and with the responsible care program. Product Benefits - Primerless to glass - One-component formulation - Cold application - Good application properties such as bead stability / good non-sag properties - Short cut-off string - Tested according to FMVSS 212/208 (with double-side airbags, no seatbelts) Areas of Application SikaTitan® -258 is suitable for direct-glazing applications in the Automotive Glass Replacement business. With its good performance and application properties it is suitable for mobile as well as inhouse installations.This product is to be used by professional experienced fitters only. If this product is used for other applications than Automotive Glass Replacement, trials must be carried out prior to use. Technical Product Data Chemical base 1-C polyurethane Colour (CQP1) 001-1) Black Cure mechanism Moisture-curing Density (uncured) (CQP 006-4) 1.1 kg/l approx. Non-sag properties (CQP 061-1) Good Application temperature +5 to +40°C Skin time2) (CQP 019-1) 40min. approx. Open time2) (CQP 526-1) 30min. approx. Curing speed(CQP 049-1) Shore A hardness (CQP 023-1 / ISO 868) 51 approx. Tensile strength (CQP 036-1 / ISO 37) 5 MPa approx. Elongation at break (CQP 036-1 / ISO 37) 650% approx. Tensile lap-shear strength (CQP 046-1 / ISO 4587) 2.5 MPa approx. Safe Drive-Away Time2) (cars) with double side airbag according to FMVSS 212 / 208 (CQP 511-1) without airbag 6 hours 2 hours Chemical Resistance SikaTitan® -258 is resistant to fresh water, seawater, limewater, sewage effluent, diluted acids and caustic solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic acids and caustic solutions or solvents. Method of Application Removal of old glass Remove damaged glass in accordance with the vehicle manufacturer’s instructions. Surface preparation Surfaces must be clean, dry and free from dust and grease. The bond faces must be prepared with a non-antistatic glass cleaner. Bonding surface must be free of contaminants before application of the product. Windshields without ceramic coatings need additional UV protection. Application Cut off the tip of the nozzle in accordance with the vehicle manufacturer's recommendations and screw onto the cartridge. It is recommended to apply the adhesive with a piston-type application gun. To ensure a uniform thickness of adhesive bead, we recommend that the adhesive be applied in the form of a triangular bead (see fig. 1 below). The substrate temperature must be between 5°C and 35°C.
$44.46
Selleys Kwik Grip High Temp Spray: Heat & Water Resistant Adhesive for Extreme Conditions Bond Like a Pro: From Marine Carpets to Car Interiors Presenting Selleys Kwik Grip High Temp Spray, a premium adhesive formulated to withstand extreme heat up to 90 degrees and resist salt water. Ideal for tasks requiring high-grade adhesion, from car headlining repairs to marine carpet installations. Key Features: Heat resistant up to 90 degrees Water and salt water resistant Fast drying High grab Applications Include: Repairing headlining in cars Adhering marine carpets in boats Suitable Materials: Wood Metal Aluminium Fabric Polyurethane foam Laminate Leather Felt Cork How to Use: Clean and dry the surface before application. Shake the can well and hold it 20cm away from the surface. Spray both surfaces liberally. Wait for up to 5-10 minutes for the adhesive to become touch dry. Align and press the surfaces together, applying
$25.00
A versatile hand kneadable, fast setting, non-rusting co-extruded epoxy repair system that can be used for repairing ferrous and aluminium metal items. It comes in a handy roll form, with the black hardener encapsulated in the grey resin part. The product hardens in 5-10 minutes, after mixing, to a black metal-like material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under water (but dry surfaces for application are best and recommended). Rapid Set (less than 10 minutes). Can be used for fuel resistant repairs. Appearance Dries Dark Grey/Charcoal Where can this product be used? Rebuilding engine parts and rusted metal etc Repairing a hole in a fuel tank Repair of iron pipes, tools and equipment Repair stripped threads Forming of nuts and bolts in place Attaching fixtures and signs Fixing radiators Repairing holes in cars and boats Patching ducts and tanks Making prototypes Thread locking Repair of down pipes and gutters Anchoring of bolts Repairing your metal outdoor furniture Set time increases at temperatures below 20°C Not recommended for plastic fuel tanks Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Not tested for drinking water contact to AS/NZ 4020:2005 What materials is this product suitable for? Steel Wide range of terrous metal and aluminium items Most plastics (pre-test required) Glass How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning Cut off required amount. Replace disc on remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to uniform colour. If mixing is difficult, warm to room temperature. Apply with pressure to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Steel will harden and begin to form a strong bond. After 60 minutes Knead-It Steel may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour, and feel a mild heat radiating from thre knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Store in a cool place for maximum shelf life Use Knead-It Multi Purpous for applications in contact with drinking water. Use Knead-It Aqua for applications in wet/submerged areas. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Steel. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$32.40
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$13.66
![Selleys Armour Flex High Performance Adhesive [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697125279_ca037dae-5a32-46a8-b3b3-d4b80d5f85fd.jpg?v=1754711933&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$45.65
![Selleys 401 Silicone Adhesive for Gaskets Resists 205 Degrees [Clear]](http://gluesaustralia.com.au/cdn/shop/files/8755f41ba29a40388c0684d41f7eeeda.jpg?v=1757753359&width=645)
Silicone 401 RTV is a one part ready to use, acid cure, room temperature vulcanising (RTV), silicone adhesive sealant. It cures rapidly on exposure to atmospheric moisture to form a versatile, durable, resilient silicone rubber. It is available in clear. Uses Silicone 401 is suitable for form-in-place gaskets and for adhesive, sealing and electrical insulating applications in manufacturing and plant maintenance. Technical Features Wide Temperature Tolerance: Remains permanently flexible under operating temperatures from – 60oC to 205oC, and will tolerate short periods of 260oC Good Chemical Resistance: Good resistance to most organic and inorganic chemicals, solvents and oils Primerless Adhesion: Adheres without primer to many metal, glass, ceramic, rigid plastic, rubber painted and wood substrates Non-toxic: Suitable for incidental food contact in food handling equipment and food contact surfaces Excellent Weatherability: Excellent resistance to ozone, UV light and ageing Good Electrical Insulating Properties: Insulating properties are comparable to other insulating rubbers at room temperature, though performs better than many other rubbers at higher temperatures and water has little effect on these properties Application Tips Not recommended for use with petrol, distillate and some other hydrocarbon solvents. These can cause softening and swelling which is undesirable in some applications. Do not use in totally confined joints where sealant is not exposed to atmospheric moisture Chemical compatibility should be tested for each application under consideration Cannot be over-painted Technical Details and Performance Indicative information only, not to be used for setting specifications. Typical Application Properties Consistency Non – sag, gun grade Tack Free Time (25oC, 50% r.h.): 15 – 20 minutes Skin Forming Time 5 to 10 minutes (depending on weather conditions) Cure Time (3mm Section @ 25oC, 50% R.H.): 24 hours Shrinkage During Curing Approximately 3.5% by volume Specific Gravity 1.04 Storage Life (Below 30oC in original unopened container):12 months Typical Mechanical Performance Properties (3 day cure @ 25oC, 50% R.H.) Tensile Strength (MPa) 1.2 Ultimate Elongation % 400 Hardness (Shore A) 25 Tear Strength (N/mm) 5.0 Joint Movement Capability ± 25% Typical Electrical Properties (at Room Temperature) Dielectric Strength kv/mm 21 Dielectric Constant @50Hz to 5MHz 2.6-2.8 Dissipation Factor Tan @50Hz-5MHz 20×10-4 to 5×10-4 Volume Resistivity (ohm-cm) 1×1013 (wet 60oC) 1×1014 (dry 23oC) Typical Thermal Properties Brittle Point –60oC Maximum Continuous Operating Temperatures 205oC Maximum Intermittent Operating Temperatures 260oC
$28.49
For your toughest jobs, go for our strongest hold–Scotch™ Extremely Strong Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies gravity, holding an item up to 20 pounds. It's weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organization to the garage, Scotch™ Extremely Strong Mounting Tape does the job quickly, easily and without the hassle of tools. Use instead of nails or screws Delivers a superior, conformable bond on contact A 60" roll holds up to 30 lbs. of objects. Not intended for use on an item that exceeds 20 lbs. Do not use on drywall or items that are more than .75” thick Easy-to-apply design with no mess or tools Ideal for use on finished/painted surfaces, metal, tile, laminate, plastic and more Ensure your surface is smooth, clean and dry for the best bond Apply at temperatures between 50°F to 100°F Made in the USA from globally-sourced materials Intended for indoor and outdoor use Color: Black
$36.63
Directions: Spray affected area Allow penetrating for 5 to 10 minutes with a damp cloth Wipe over Allow drying Uses: Household, motor vehicles, boating & office carpets
$7.00
Directions: Spray affected area Allow penetrating for 5 to 10 minutes with a damp cloth Wipe over Allow drying Uses: Household, motor vehicles, boating & office carpets
$4.00
PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.
$16.17
Loctite 222 Threadlocker prevents corrosion, loosening from shock or vibration, and seals to prevent leakage. It also allows for simple, hand tool disassembly without shearing the screw. Easy to remove, it is typically used with small screws up to 1/4 inch. Recommended on Low strength Stops vibration loosening of screws and seals against leakage Prevents thread corrosion Dismantle with normal hand tools How to Use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole. For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours. Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush. For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot.
$18.13
Hold It Australia T90 PENETRATOR Wicking Grade for Close Fitting Parts - 50ml Description: HOLDIT AUSTRALIA T90 Penetrant is a fast-curing, low viscosity anaerobic compound that seeks voids in assembled components to cure anaerobically on close-fitting metal parts. It's ideal for securing tightly fitted assemblies. Applications T90 is excellent for post-assembly application, effectively preventing loosening of metal threaded fasteners. It is suitable for securing parts with minimal clearance and repairing hairline cracks in metal castings. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. For porosity or hairline cracks in casting products, brush directly onto the parts. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Gorilla takes epoxy to a new level—the Gorilla Tough level. With its superior solvent and water resistance, Gorilla Epoxy adhesive is incredibly strong and durable for household and automotive repairs alike. The easy-to-use syringe keeps the epoxy resin and hardener separate, so it is easy to dispense and won’t harden over time. The two-part, gap-filling formula easily bonds steel, aluminum, glass, wood, ceramic, tile and most plastics. Plus, it dries in an ideal, crystal-clear finish that makes projects look spotless. Features: Dries Clear: Ideal for clean, easy finishing 5 Minute Set: Plenty of repositioning time for the perfect fit. Gap-Filling: Fills voids and bonds uneven and vertical surfaces. Water Resistant: Withstands moderate exposure to water Solvent resistant Non-Toxic once cured Easy-to-use syringe: Separate barrels of epoxy resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses. Directions Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together. Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. Prepare Your Work Area and the Surface If you’re using Gorilla Epoxy for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together. Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. Mixing Gorilla Epoxy Remove the black cap from the two syringes. With tip pointing upward, cut or snap the end from tip of the syringes. With the tip still pointing upward, eliminate air and ensure even dispensing by slowly pushing the plunger until both the resin and the hardener are at the tip Push the plunger to dispense even amounts of resin and hardener onto a clean, disposable, contained surface. The package itself can be used as a mixing tray. If you flip the plastic blister shell over, you can use the small well as a starter dish to begin dispensing until both the resin and hardener are flowing equally. Once the flow is even, move to the larger mixing well to dispense your even ratio. Mix the two parts for about 20 seconds, until the mixture is uniform. Apply within 5 minutes.As you mix, you will notice that the epoxy warms up. This is a reaction that occurs as the resin and hardener combine. Application After mixing is complete, apply Gorilla Epoxy within 5 minutes. The epoxy mixture will continue to thicken and the bond strength will decrease the longer you wait to apply. Clamping To reach maximum bond strength, clamp project together and leave undisturbed. Important Cure Times Set: 5 minutes to apply and position Handling: Allow to cure for 30 minutes undisturbed (no weight or handling) Final Cure: Allow 24 hours for load-bearing weight Storage: To close, pull plunger slightly back. Wipe tip clean with dry cloth and align notch on tip and cap. Close tightly. Visit our FAQs for more information on what surfaces Gorilla Epoxy will bond, clean up information and more. FAQ Is Gorilla Epoxy gap filling? Yes. Gorilla Epoxy is gap filling. It will fill voids and bond uneven and vertical surfaces. If filling gaps outdoors, note that Gorilla Epoxy may yellow over time with exposure to sunlight. What is the shelf life? Are there storage tips to extend the shelf life? Shelf life for Gorilla Epoxy is a maximum of two years. The adhesive is not activated until the resin and hardener come in contact with one another, so the shelf life is likely to be much longer if the epoxy tip is wiped clean after each use and the cap is securely replaced. Make sure you notice the notch on the cap and be sure to align that with the notch on the syringe tip. This will further ensure the two parts do not accidentally mix. What is the best application temperature? For best results, apply in room temperature situations. Application in cold temperatures will slow the cure time of Gorilla Epoxy, while application in hot temperatures can speed up the cure time. Gorilla Epoxy’s cured bond withstands temperatures ranging from -23° to 82°C Do I need to use clamps with Gorilla Epoxy? How long? Clamps are recommended for use during setup to ensure the bond sets correctly. Set Time: 5 minutes to mix, apply and position Handling Time: Leave 30 minutes undisturbed (clamping is recommended) Full Cure Time: 24 hours for load-bearing weight How much Gorilla Epoxy do I apply? Gorilla Epoxy is a very strong adhesive. It does not take a lot to get a strong bond. Average coverage from our 25 mL epoxy syringe will cover 100 square inches. What can I use as a mixing tray or stir stick? A mixing tray and stir stick will be included in your Gorilla Epoxy package. Other ideas for mixing trays include aluminum foil trays, cardboard, or paper/plastic plates. Try using popsicle sticks, plastic utensils or straws for mixing. What is Gorilla Epoxy? Gorilla Epoxy is a two-part formula that requires equal parts of resin and hardener mixed together for activation. For best strength results, mix a 1-to-1 ratio of resin and hardener. Once mixed, Gorilla Epoxy is capable of bonding many materials and offers high strength results. How do I remove Gorilla Epoxy? Gorilla Epoxy is a very strong adhesive and is solvent resistant. Removing dried adhesive is difficult to do. Acetone will soften the epoxy; however, full removal will require mechanical means, such as scraping, rubbing, or sanding. Uncured Removal: Skin: Acetone, isopropyl alcohol, 2–3 washings with soap and water. Reminder: Cured glue requires mechanical means, such as rubbing or washing with exfoliating soaps. Hair: Isopropyl alcohol Clothes and Carpet: Isopropyl alcohol. For clothes and carpet, avoid acetone, soap and water, and mineral spirits, as they will not work well on fabric. What surfaces will Gorilla Epoxy bond? Gorilla Epoxy is very versatile. It boasts high-strength results for steel, wood, aluminum, ceramic, tile, glass, most plastics, pressure-treated lumber and much more! What surfaces will Gorilla Epoxy bond? Gorilla Epoxy is water resistant, which means it will resist moderate exposure to water but should not be fully submerged. If you need an adhesive that is 100% waterproof, check out our Original Gorilla Glue®. How do I dispense Gorilla Epoxy? Make sure all surfaces are clean, dry and free of oil. To improve adhesion, roughen up smooth surfaces with sandpaper before gluing. Remove black cap from the middle of the plunger. With tip pointing upward, snap end from the tip of the syringe. Slowly push plunger until resin and hardener are at the tip, then dispense evenly. The package blister can be used as a mixing tray. Mix for at least 20 seconds until the mixture is uniform. Apply to surface within 5 minutes. Clamp surfaces together or leave undisturbed for 30 minutes. To close, pull plunger slightly back. Wipe syringe tip with a clean, dry cloth then snap the black cap on tightly.
$19.89
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the flange faces first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 58-31 Gasketing Elastic Anaerobic Adhesive 75ml Loxeal 58-31 is a high-performance anaerobic gasketing adhesive that cures to an elastic, flexible film, replacing solid pre-formed gaskets on flange joints. It seals against gases, water, LPG, fuels, oils and a wide range of chemicals, resists shocks and vibration, and keeps sealing from -55°C right up to +180°C. The thixotropic consistency stops the sealant migrating before or during cure, and the red adhesive fluoresces under blue light for easy inspection on the production line. Why choose Loxeal 58-31? Elastic cured film accommodates joint movement while maintaining the seal Higher strength and faster fixture than general-purpose flange sealants Extended service temperature to +180°C Thixotropic — no running or migration on vertical flanges Fluorescent under blue light for quality-control checks Dismantles with standard tools when service is required Typical applications Sealing flange joints on pumps, gearboxes and differential housings where an elastic, vibration-resistant gasket and elevated temperature capability are needed — demanding automotive, transport and industrial maintenance work. How to use Clean and degrease the flange faces (Loxeal Cleaner 10 recommended). Apply enough product to fill the joint gap completely. Assemble the parts and hold them in place while curing. Use Loxeal Activator 11 for faster cure on passive metals or at low temperatures. To dismantle, use normal tools (heat to +150°C/+250°C if necessary), remove cured residue mechanically and clean with acetone. Cure times At +25°C on steel: handling strength in 10–20 minutes, functional strength in 1–3 hours and full cure in 6–12 hours. Cure speed varies with gap, substrate and temperature. Specifications Chemistry Anaerobic methacrylate Colour Red (fluorescent under blue light) Viscosity (+25°C) 70–600 Pa·s Specific gravity (+25°C) Approx. 1.1 g/ml Maximum gap fill 0.50 mm Breakaway torque (ISO 10964) 15–25 N·m Prevailing torque (ISO 10964) 18–28 N·m Shear strength (ISO 4587) 8–13 N/mm² Tensile strength (ISO 6922) 7–10 N/mm² Impact strength (ASTM D-950) 4–7 kJ/m² Service temperature -55°C to +180°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Fully cured Loxeal 58-31 offers excellent resistance to motor oil and gearbox oil at +125°C through 1,000 hours, excellent-to-good resistance to hot 50% water/glycol mixtures, and moderate resistance to gasoline on prolonged exposure. Important notes Recommended for metal surfaces — seek technical advice before applying to non-metal parts. Uncured adhesive can damage coatings, some plastics and elastomers, and may cause delayed stress-cracking in certain thermoplastics. Store cool and dry at no more than +25°C; do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$59.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the flange faces first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 58-14 Gasketing Anaerobic Adhesive 75ml Loxeal 58-14 is a medium-strength anaerobic gasketing adhesive that forms a flexible in-place gasket between flange faces, doing away with pre-cut solid gaskets. The highly thixotropic formula stays exactly where it is applied without migrating before or during cure, and the cured film seals dependably against gases, water, LPG, fuels, oils and many other chemicals across a service range of -55°C to +150°C. Why choose Loxeal 58-14? One liquid gasket replaces an inventory of pre-formed paper, cork and plastic gaskets Flexible cured film shrugs off shocks and vibration Thixotropic — stays put on vertical and horizontal flanges Fills gaps up to 0.50 mm and compensates for minor surface imperfections Assemblies can be dismantled later with standard workshop tools Typical applications Gasketing and sealing of flange joints on pumps, gearboxes, differential housings and similar close-fitting metal assemblies in automotive workshops, plant maintenance and general engineering. How to use Clean and degrease both flange faces (Loxeal Cleaner 10 recommended). Apply a continuous bead so the joint gap is completely filled. Assemble the parts and hold them in position while the adhesive cures. On passive metals or in cold conditions, accelerate the cure with Loxeal Activator 11. To dismantle, use normal tools (heating the parts to +150°C/+250°C helps if needed), remove cured residue mechanically and clean up with acetone. Cure times At +25°C on steel: handling strength in 15–30 minutes, functional strength in 3–6 hours and full cure in around 24 hours. Cure speed varies with gap size, substrate and temperature. Specifications Chemistry Anaerobic methacrylate Colour Orange Viscosity (+25°C) 28,000–100,000 mPa·s, highly thixotropic Specific gravity (+25°C) Approx. 1.1 g/ml Maximum gap fill 0.50 mm Shear strength (ISO 4587) 5–10 N/mm² Tensile strength (ISO 6922) 5–8 N/mm² Impact strength (ASTM D-950) 3–5 kJ/m² Service temperature -55°C to +150°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Once fully cured, Loxeal 58-14 shows excellent resistance to motor oil and gearbox oil at +125°C out to 1,000 hours, and good long-term resistance to gasoline and to 50% water/glycol mixtures at +87°C. Important notes Formulated for metal surfaces — contact a technical adviser before use on non-metal parts. The liquid adhesive can attack coatings, some plastics and elastomers, and may induce delayed stress-cracking in certain thermoplastics. Store in a cool, dry place at no more than +25°C and never return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use and follow standard workshop hygiene practices. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$49.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the flange faces first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 59-10 Gasketing High Temperature Anaerobic Adhesive 75ml Loxeal 59-10 is a single-component, medium-strength anaerobic flange sealant with outstanding heat resistance up to +200°C. It cures at room temperature when confined without air between close-fitting metal surfaces, forming a durable in-place gasket that replaces pre-formed gaskets, allows wider machining tolerances and still permits dismantling with normal tools. The cured seal is highly resistant to vibration, heat, water, gases, LPG, oils, fuels and many chemicals. Why choose Loxeal 59-10? Service temperature from -55°C to +200°C — ideal for hot-running assemblies Replaces pre-formed gaskets and assures true metal-to-metal contact Fills gaps up to 0.50 mm, accommodating greater machining tolerances Highly resistant to vibration, oils, hydrocarbons and coolants Parts remain serviceable — dismantle with everyday workshop tools Typical applications Sealing flat, rigid flange joints on pumps, gearboxes, camshaft blocks and motor flanges — anywhere a heat-tolerant, vibration-proof formed-in-place gasket is required. How to use Clean and degrease the mating surfaces (Loxeal Cleaner 10 recommended). Apply enough product to fill the joint gap completely. Bring the parts together and leave undisturbed until cured. On passivated surfaces or at low temperature, use Loxeal Activator 11 to speed the cure. For disassembly, use normal tools (heat to +150°C/+250°C if needed), remove cured residue mechanically and clean with acetone. Cure times At +25°C on steel: handling strength in 15–30 minutes, functional strength in 3–6 hours and full cure in 6–12 hours. Cure speed depends on substrate, gap and temperature. Specifications Chemistry Anaerobic methacrylate Colour Red Viscosity (+25°C) 50–300 Pa·s Specific gravity (+25°C) Approx. 1.05 g/ml Maximum gap fill 0.50 mm Shear strength (ISO 4587) 5–10 N/mm² Tensile strength (ISO 6922) 6–8 N/mm² Impact strength (ASTM D-950) 3–5 kJ/m² Service temperature -55°C to +200°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance After full cure, Loxeal 59-10 maintains excellent resistance to motor oil and gearbox oil at +125°C and to 50% water/glycol coolant at +87°C through 1,000 hours; resistance to gasoline is excellent initially, reducing with prolonged immersion. Important notes Recommended for metal surfaces — seek technical advice before use on non-metal parts. Liquid product may damage coated parts and elastomers, and contact with some thermoplastics can induce stress-cracking that is not immediately visible. Store in a cool, dry place at +25°C or below; never return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$54.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-03 Threadlocker Medium Strength Anaerobic Adhesive 10ml Loxeal 55-03 is a medium strength anaerobic threadlocker for nuts, bolts and studs of all types that may need to be dismantled later with standard hand tools. It tolerates minor oil contamination on the parts, so it keeps performing where threads are not perfectly clean. Once cured it resists vibration, corrosion, water, gas, oils, hydrocarbons and many other chemicals, and it holds its sealing properties from -55°C to +200°C (up to +250°C for short periods), with proven unscrewing resistance at +200°C. Why choose Loxeal 55-03? Medium strength – assemblies can be dismantled with normal tools when servicing is needed Tolerates light oil contamination on threads Locks and seals fasteners in one step, stopping loosening caused by vibration Wide service temperature range of -55°C to +200°C Blue colour, fluorescent under blue light, for easy inspection on the production line Seals the thread against ingress, helping prevent rust and fretting corrosion Certified and approved Approved as a gas-tight sealant for threaded fittings to European norm EN 751-1 (DVGW and Gaz de France) WRAS approved – suitable for use in contact with potable water Compliant with the UBA (German Environment Agency) declaration for potable water applications NSF registered in category S4 as acceptable for use as an adhesive in and around food processing areas Typical applications Securing nuts, bolts, studs and screws on machinery, vehicles and equipment subject to vibration Sealing threaded fittings on gas, water and compressed air lines Automotive, plumbing and general maintenance work where later disassembly must remain possible How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before putting the joint into service. On passive surfaces (e.g. stainless steel, plated parts) or in cold conditions, pre-treat with Loxeal Activator 11 to speed the cure (this may slightly reduce final strength). Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate resin Colour Blue (fluorescent under blue light) Viscosity (+25°C) 1,700–9,000 mPa·s, thixotropic Specific gravity (+25°C) 1.07 Max thread size / gap fill M36 / 0.25 mm Shear strength (ISO 10123) 9–13 N/mm² Breakaway torque (ISO 10964) 18–23 N·m Prevailing torque (ISO 10964) 9–16 N·m Service temperature -55°C to +200°C (+250°C short term) Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, ethanol and biodiesel, with good resistance to petrol, brake fluid, 50% water/glycol and acetone after 1,000 hours of exposure. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. Not approved for use with pure oxygen or oxygen-rich systems, and not suitable for sealing chlorine or other strong oxidising agents. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$14.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 53-11 Retaining Compound Anaerobic Adhesive 50ml Loxeal 53-11 is a medium strength anaerobic retaining compound for fixing bearings, liners, bushes, keys and splines into housings and onto shafts. It fills the space between cylindrical parts to give 100% surface contact, boosting load-carrying capacity while still allowing disassembly with standard workshop methods. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals across a service range of -55°C to +150°C. Why choose Loxeal 53-11? General purpose retainer for bearings, bushes, liners, keys and splines Medium strength – parts remain serviceable and can be dismantled Fills the joint completely, preventing fretting corrosion between mating parts Increases load transmission compared with a mechanical fit alone Low viscosity wicks into close-fitting cylindrical assemblies Resists vibration, oils, fuels and many chemicals from -55°C to +150°C Typical applications Retaining bearings and bushes in housings and on shafts Securing cylinder liners, keys, splines and sleeves Workshop repairs to restore security in worn cylindrical fits How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts, seating them fully, and hold in position for the cure time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Yellow (fluorescent under blue light) Viscosity (+25°C) 400–650 mPa·s Specific gravity (+25°C) 1.05 Max thread size / gap fill M20 / 0.12 mm Shear strength (ISO 10123) 8–12 N/mm² Breakaway torque (ISO 10964) 11–20 N·m Prevailing torque (ISO 10964) 15–25 N·m Impact strength (ASTM D-950) 1–5 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, petrol and brake fluid at +25°C (out to 5,000 hours), with good resistance to 50% water/glycol at +87°C. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$39.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 82-21 Retaining Compound Fast Cure Anaerobic Adhesive 50ml Loxeal 82-21 is a fast curing, high strength anaerobic retaining compound for close-fitting cylindrical parts – shafts, bushes, pulleys and rotors. Its low viscosity flows into precise fits, reaching handling strength in as little as 5–10 minutes, and cures to a tough bond with 17–22 N/mm² shear strength. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils and hydrocarbons across a service range of -55°C to +150°C. Why choose Loxeal 82-21? Fast fixture – handling strength in 5–10 minutes keeps jobs moving High strength bond for permanent retention of close-fitted parts Low viscosity penetrates precise cylindrical fits (up to 0.10 mm gap) High impact strength of 11–15 kJ/m² for parts under shock loading Fills the joint completely, preventing fretting corrosion Resists vibration and many chemicals from -55°C to +150°C Typical applications Bonding pulleys, gears and rotors onto shafts Retaining bushes and bearings in precision housings Production assembly where fast fixture times are needed How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts promptly, seating them fully, and hold for the fixture time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 5–10 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green Viscosity (+25°C) 120–180 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M12 / 0.10 mm Shear strength (ISO 10123) 17–22 N/mm² Breakaway torque (ISO 10964) 24–35 N·m Prevailing torque (ISO 10964) 50–60 N·m Impact strength (ASTM D-950) 11–15 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to refrigerants (Freon) at +25°C, excellent resistance to petrol out to 500 hours, and moderate resistance to motor and gearbox oils at +40°C over extended exposure. Important notes High strength – intended as a permanent retaining bond. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$44.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 83-54 Threadlocker High Strength Anaerobic Adhesive 50ml Loxeal 83-54 is a high strength anaerobic threadlocker for permanently locking and sealing studs, nuts, bolts and threaded fasteners that are not intended to be dismantled. It can be used on all metals, in both free and interference fits, and delivers high unscrewing resistance with temperature performance up to +200°C. The cured adhesive stands up to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals, making it a direct alternative to other high-strength studlocks such as Loctite 263. Why choose Loxeal 83-54? High strength, permanent locking for fasteners that must not come loose Strong prevailing torque of 50–65 N·m keeps holding even after the initial break Service temperature from -55°C to +200°C Suitable for all metals, in free or forced (press-fit) matings Green colour, fluorescent under blue light, for easy quality inspection Seals the thread, protecting against corrosion and leakage Typical applications Permanent locking of studs into engine blocks, housings and castings Heavy machinery, driveline and suspension fasteners exposed to strong vibration Fasteners on pumps, compressors and equipment where loosening would be a safety risk How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before loading the joint. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 5–10 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green (fluorescent under blue light) Viscosity (+25°C) 450–650 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M20 / 0.15 mm Shear strength (ISO 10123) 15–20 N/mm² Breakaway torque (ISO 10964) 25–35 N·m Prevailing torque (ISO 10964) 50–65 N·m Service temperature -55°C to +200°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to petrol and brake fluid at +25°C, good resistance to 50% water/glycol at +87°C, and good short-term resistance to motor and gearbox oils at +125°C (moderate on extended exposure). Important notes Designed as a permanent locking product – routine disassembly is not intended. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$44.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-03 Medium Strength Anaerobic Threadlocker Loxeal 55-03 is a medium strength anaerobic threadlocker for nuts and bolts of all types that may need to be dismantled later. It tolerates minor oil contamination on parts, so it performs even on as-received fasteners, and it holds its locking and sealing properties from -55°C to +200°C (up to +250°C for short periods). The direct alternative to Loctite 243. Why choose Loxeal 55-03 Oil tolerant: cures reliably on lightly oiled threads without extensive cleaning. High temperature: proven unscrewing resistance at +200°C. Serviceable strength: locks firmly against vibration yet can be dismantled with hand tools. Wide chemical compatibility: resists water, gas, oils, gasoline, brake fluid, ethanol, biodiesel and many chemicals. Blue colour, fluorescent under blue light for easy inspection. Certified and approved Gas: approved as gas-tight sealant for threaded fittings to EN 751-1 (DVGW and Gaz de France). Potable water: WRAS approved and compliant with the German UBA declaration for drinking water use. Food areas: NSF registered category S4 for use as an adhesive in and around food processing areas. Typical applications Locking machine bolts, pump housings, gearbox fasteners and automotive nuts and bolts subject to vibration. Threaded fittings in gas and potable water systems where certified products are required. Maintenance work on equipment where fasteners arrive lightly oiled. How to use Clean and degrease parts where practical (Loxeal Cleaner 10 recommended); minor oil films are tolerated. Apply enough product to completely fill the engaged threads. Assemble the parts and hold for the curing time. On passive surfaces or in cold conditions, Loxeal Activator 11 speeds curing (may slightly reduce final strength). Cure times at +25°C Handling: 10 to 20 minutes Functional: 1 to 3 hours Full cure: 24 to 36 hours depending on substrate, gap and temperature Specifications Chemistry Anaerobic methacrylate resin Colour Blue (fluorescent under blue light) Strength grade Medium (dismantlable) Viscosity at +25°C 1,700 to 9,000 mPa·s, thixotropic Specific gravity Approx. 1.07 g/ml Friction coefficient Approx. 0.10 Max thread / gap filling M36 / 0.25 mm Shear strength 9 to 13 N/mm² (ISO 10123) Breakaway torque 18 to 23 N·m (ISO 10964) Prevailing torque 9 to 16 N·m (ISO 10964) Service temperature -55°C to +200°C (+250°C short term) Approvals EN 751-1 (DVGW, Gaz de France), WRAS, UBA, NSF S4 Shelf life 1 year in unopened packaging at up to +25°C Chemical resistance Excellent long-term resistance to motor oil and gearbox oil at +125°C, ethanol and biodiesel at room temperature; excellent to good resistance to gasoline, brake fluid and 50 percent water glycol. Important notes For metal fasteners. Liquid product can damage coatings, some plastics and elastomers; stress cracking may develop with some thermoplastics. Not approved for pure oxygen or oxygen-rich systems, and not suitable as a sealant for chlorine or other strong oxidising agents. For disassembly use normal tools; if needed heat parts to +150°C to +250°C, remove cured residue mechanically and clean with acetone. Store cool and dry at or below +25°C. Do not return used product to the bottle. Safety Consult the Safety Data Sheet before use. For professional and industrial use. Follow all handling instructions on the product label. All technical information is provided as a guide only. Always verify suitability with your specific materials and operating conditions before use.
$39.95
You have seen 48 out of 160 products
Products suited to automotive environments. Choose sealants, adhesives and accessories that match moisture, temperature and movement demands in automotive areas. Look for mould resistance, flexibility, UV stability or potable‑water suitability where shown. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
