Note: If you are working on a timber floor, you will need to use Fix-A-Floor Polyurethane for Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive, now patented, is an extra-strength bonding adhesive designed specifically for re-bonding loose and hollow tiles, marble and stone without the cost and mess of removing or replacing them. Fix-A-Floor is a simple DIY repair solution that is fast, easy and affordable, and surprisingly rewarding. If you can operate a drill, a caulking gun and mix a small batch of grout, you can do it. It works on all types of subfloor materials. Just Drill & Fill! Tip: For more precise application or smaller holes, you can include the 30 mL Adhesive Syringe with Blunt Tip Fill Needle when purchasing this product. It makes applying the adhesive cleaner and more accurate, especially in tight or narrow grout lines. The Nozzle The nozzle of the 300 mL Fix-A-Floor tube is specially engineered with a pre-drilled 3 mm hole to make it ideal for filling drilled holes in loose or hollow tile, marble and stone floors. It is firm enough to form a strong seal for optimal flow and complete coverage. Markings on the nozzle indicate cut points for 4.5 mm, 6 mm or any size you need, making it suitable for both narrow grout lines and wider applications. The Adhesive Fix-A-Floor Repair Adhesive is strong and flexible, featuring elastomeric bonding properties that prevent future issues caused by foundation movement, expansion and contraction of the subfloor or poor original installation. Used by flooring professionals for years, this product allows any homeowner to fix loose, hollow or squeaky tiles quickly and permanently. It is non-toxic, non-flammable and eco-friendly. Whether you are repairing a small area or a large floor section, Fix-A-Floor delivers lasting results and is guaranteed for the life of your floor. Just Drill & Fill! FAQs Q: Will Fix-A-Floor work with heated floors?A: Yes. Many customers use Fix-A-Floor over heated floor elements with no issues. Turn off the heating before, during and for 48 hours after applying. Q: Some of my grout is missing. Can I still use Fix-A-Floor?A: Yes. If small gaps or cracks exist, simply Drill & Fill. The adhesive will re-bond and stabilise loose areas. If the grout is completely missing, re-grout lightly, allow it to dry and then apply Fix-A-Floor. Q: Can I repair my whole floor or just one tile?A: Fix-A-Floor works on all sizes of problem areas, from a single tile to an entire room. It is suitable for all types of tile, marble and stone floors. Q: Can I use Fix-A-Floor outside?A: Yes. It performs well in both interior and exterior applications, including patios and decks. Q: Can I use Fix-A-Floor in showers or pools?A: No. It is not recommended for areas exposed to constant or excessive moisture. Q: Is Fix-A-Floor safe?A: Yes. It is a non-toxic, non-flammable, water-based adhesive that is safe and environmentally friendly. Q: Can I use it to re-glue a tile that has come loose?A: Yes. Apply Fix-A-Floor directly to the floor where the tile was, press the tile firmly into place, apply weight and allow to cure for 24 hours. Q: Do I need to place weight on the floor after filling?A: It is recommended to place some weight, such as a heavy object or bucket, on the area to aid curing and ensure even distribution. It is not mandatory but helps achieve optimal results. Q: What if adhesive does not appear from other holes?A: The adhesive may still be spreading beneath the tile. Move to the next hole and continue filling. Make sure you are not pressing the nozzle down onto the subfloor during application.
$34.95
Note: This product is formulated for timber floors. If you need an adhesive for tiled floors, please use the regular Fix-A-Floor available Click here. NEW – Fix-A-Floor Polyurethane Wood Floor Repair Adhesive features an extra-strength, super-blend formula specifically designed for re-bonding loose, hollow, squeaky, popping, or bouncy timber floors. There’s no need to remove or replace floorboards — simply Drill & Fill for a long-lasting, nearly invisible repair. The precision nozzle allows for very small drill holes, ensuring a clean finish. Ideal for all solid hardwood, engineered timber, and bamboo floors. Suitable for both indoor and outdoor use, and for small or large repair areas. Odourless and very low in VOCs. Coverage: One 300 mL tube covers approximately 0.37 m² (around 600 mm x 600 mm). Just Drill & Fill! Flooring professionals often prefer polyurethane when repairing timber floors due to its strength and flexibility. The Fix-A-Floor polyurethane formula does not foam or expand when applied and cures within 24 hours. Once set, it moves naturally with the timber’s expansion and contraction, preventing cracking or bond failure. Perfect for permanently fixing loose, squeaky, or bouncy floors. Not recommended for use in moist or wet areas. The Fix-A-Floor Large Application Syringe is another excellent option for applying the adhesive if you’d like to drill even smaller holes than 3.5 mm. Always test on a small area first to confirm desired results, and keep from freezing before use. Directions for Repairing Timber Floors: Locate problem areas by tapping the floor with a wooden dowel, broom handle, or similar object, and mark the perimeter using chalk or painter’s tape. Inside the marked area, use a 3.5 mm drill bit and drill at least one hole on each end of the affected floorboard(s). Larger areas may require additional holes. Vacuum debris from each hole. Remove the cap and unscrew the nozzle. Pierce a large hole in the tube with an awl or similar tool. If needed, clear the nozzle before screwing it back on. Using a quality caulking gun, inject Fix-A-Floor into each drilled hole. When adhesive seeps from adjacent holes, you have achieved full coverage. Place a finger over the nozzle when moving between holes to prevent spills. Once complete, wipe away any excess with a damp cloth or sponge and allow to cure for 24 hours before filling holes. Use a matching timber filler or putty from your local hardware store. Clean any residue with mineral turpentine. Your floor is FIXED!
$49.95
Sikaflex®-291 Black Marine-Grade Polyurethane Sealant 150mL is a premium, one-component, non-sag adhesive sealant specially formulated for marine environments. It cures on exposure to atmospheric moisture, forming a strong, elastic, and durable bond that resists saltwater, vibration, and weathering. Trusted by boat builders and marine professionals worldwide, Sikaflex®-291 meets International Maritime Organisation (IMO) standards for safety and performance. Features & Benefits Marine-grade polyurethane formula with superior adhesion Excellent weathering and saltwater resistance Elastic and vibration-resistant for long-lasting seals Low odour and non-corrosive composition Can be sanded and overpainted after curing Maintains flexibility across wide temperature ranges Where to Use Sealing and bonding on boats, yachts, and marine structures Deck fittings, hatches, and hardware installations Elastic, vibration-resistant joints above and below deck Bonding wood, metals, primers, coatings, ceramics, and GRP plastics Important Notes Not suitable for plastics prone to stress cracking such as Plexiglas or Polycarbonate Surfaces must be clean, dry, and free from grease or dust before application Recommended application temperature: 5°C to 40°C Technical Details Chemical Base 1-component polyurethane Colour Black Cure Mechanism Moisture-curing Density (uncured) Approx. 1.3 kg/L Shore A Hardness 40 Tensile Strength 1.8 MPa Elongation at Break 500% Temperature Resistance -50°C to +90°C (up to 180°C short term) Skin Time Approx. 60 minutes Shelf Life 12 months (stored below 25°C) Packaging 150 mL Tube For marine sealing and bonding you can trust, Sikaflex®-291 delivers professional-grade strength, flexibility, and durability on every project.
$18.70 $0.12/ml
![Selleys No More Gaps Coloured Caulk Sealant 450g [Brilliant White]](http://gluesaustralia.com.au/cdn/shop/files/c306de337e4245d585ba9870c44c5c2b.jpg?v=1757756191&width=645)
No More Gaps Coloured Gaps No More Gaps Coloured Gaps offers a long-lasting, colour-matched finish, suitable for both interior and exterior use. It comes in a wide range of colours, with no need to paint over (although it is paintable if required). It provides superior flexibility to cope with building movement, hiding cracks and gaps longer, with greater than 350% elongation/stretch and up to +/- 20% movement capability. Key Features Long-lasting, colour-matched finish Suitable for Interior & Exterior use Available in a great colour range, with no need to paint over (Paintable if required) Superior flexibility to cope with building movement, hiding cracks and gaps longer Greater than 350% elongation/stretch and up to +/- 20% movement capability Good resistance to weathering Superior adhesion to a broad range of surfaces, resulting in a lasting finish Mould and mildew resistant Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles (not exposed to water) In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Bare or painted surfaces Colorbond Many other building materials How to Use Ensure the surface is clean, dry, and free from dust, grease, flaking/powdery paint, and old or crumbling caulk. Cut the seal and nozzle, fit it to the top of the cartridge, and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking Gun. Hold the caulking gun at a 45° angle and apply, forcing the product into the gap. Smooth with a wet finger or spatula. Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow surface to skin thoroughly prior to painting with water-based paints. If using oil-based paints or for large gaps, allow the sealant to set for about 24 hours and ensure the product is completely cured. Avoid water contact until fully cured – 72 hours or longer in cold weather. Limitations Not recommended for foot traffic areas, gaps between tongue and groove boards, or weatherboard overlaps. Use Selleys No More Gaps Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards, and Selleys No More Gaps Exterior & Weatherboard Gap Filler for weatherboard overlaps. Not suitable for areas in prolonged contact with water (e.g., showers, pools, & spas). Use Selleys Silicone Sealant for significant joint movement or areas of frequent water immersion. Do not apply or store below 5°C. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easier cleanup. When first applying, extrude a small amount onto scrap material to ensure smooth, continuous flow of gap filler. If wiping off excess with a wet finger, wet it with water (not saliva) to avoid bacteria that can promote mould growth. Allow surfaces to skin before painting, approximately 30 minutes. Protect from rain until the surface is firmly skinned. Some water-based undercoats and flat paints may crack when drying. To reduce this, allow the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting. Keep a pack of Selleys Sugar Soap Wipes handy for easy cleanup. Clean Up Water-based, so clean up with water. Uncured product may be removed with water. Cured product can be removed by sanding and scraping. Size 450g Cartridge Colours Black Brilliant White Brown Cedar Charcoal Coffee Cream Ivory Light Grey Technology Water-Based Use Interior & Exterior
$0.00 - $15.00
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.00
![Selleys Marine Flex For Boats Pools and Spas Water Proof [White]](http://gluesaustralia.com.au/cdn/shop/files/091876a6025d44ea89c711822b3ea3d8.jpg?v=1757752868&width=645)
Selleys Marine Flex is a high-performance adhesive and sealant designed for marine and water-exposed applications. Using Sil-X advanced polymer technology, it provides a permanent watertight seal above and below the waterline, even in salt, fresh, or chlorinated water. Key Features Cures and bonds underwater No primer required for most surfaces Strong and flexible bond absorbs vibration and movement Solvent-free and isocyanate-free formulation Sandable once cured 10-year watertight seal guarantee (above waterline) Where to Use Ideal for marine, pool, spa, and construction projects where water exposure or movement is expected. Suitable for bonding and sealing: Boat hulls, fittings, and deck seams Pool tiles, coping, and skimmer boxes Concrete, fibreglass, sealed timber, and metal surfaces Glass, ceramics, and most rigid plastics Technical Details Technology Sil-X advanced polymer Colour White or Black Size 410g cartridge Finish Smooth, paintable once cured How to Apply Ensure surfaces are clean and free from grease, oil, or dust. Can be applied to damp or wet surfaces. Cut the nozzle to the desired bead size and apply using a standard caulking gun. Tool the sealant immediately with a soapy water solution before it begins to skin. Allow to cure fully before sanding or painting if required. Limitations Not suitable for polyethylene (PE), polypropylene (PP), or PTFE materials Gelcoat surfaces should be lightly sanded before application The watertight guarantee applies to applications above the waterline Why Choose Selleys Marine Flex When you need a sealant that can withstand constant water exposure, movement, and vibration, Selleys Marine Flex delivers unmatched reliability. It bonds powerfully, stays flexible, and ensures a lasting waterproof finish for marine, pool, or construction applications.
$28.00
![Selleys No More Gaps Multipurpose Sealant Filler 475g [White]](http://gluesaustralia.com.au/cdn/shop/files/62810ec4c8d842009839ace74d1cac64.png?v=1757753067&width=645)
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 300% elongation/stretch and up to +/- 15% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage. Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application). Is formulated for long term resistance to cracking and crumbling. Easy water clean-up Will not stain building materials. Has good resistance to weathering. Low toxic, low odour, low VOC, less harmful to the environment Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles which are not exposed to water In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Paint Many other building materials
$5.00
Selleys All Clear Crystal: The Ultimate Multipurpose Sealant Key Features Works on wet, oily, and dirty surfaces Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Best For Metal, Timber, Glass, Glazed tiles, Brick, Stone, and many plastics (may damage polystyrene and polycarbonate). Applications Sky lights Window frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' entries Shower screens Sinks and basins Caravans and recreational vehicles How to Use Use only in a well-ventilated area. Ensure surface is clean and dry. Apply with a caulking gun and smooth with a tool dipped in turps. Limitations May damage some plastics Not for permanent water immersion Not suitable for use over silicones or polystyrene foam Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by cutting and scraping. Technology & Cure Time Solvent-based, with a full cure time of 48-72 hours. For both interior and exterior use.
$16.00
![Fix-A-Floor Loose Tile Repair Adhesive Needle [Pro Pack] Includes a Micro Syringe Injector and Drill Bit](http://gluesaustralia.com.au/cdn/shop/files/One_33b7ac3c-91f8-445e-9f7a-f35eb32fd49e.jpg?v=1760493150&width=645)
![Fix-A-Floor Loose Tile Repair Adhesive Needle [Pro Pack] Includes a Micro Syringe Injector and Drill Bit](http://gluesaustralia.com.au/cdn/shop/files/513iY1tnifL._SL1013_2cc193b4-9c50-4e36-a6e8-69a36d42769f.jpg?v=1760493150&width=645)
Note: If you are working on a timber floor, you will need to use Fix-A-Floor Polyurethane for Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive, now patented, is an extra-strength bonding adhesive designed specifically for re-bonding loose and hollow tiles, marble and stone without the cost and mess of removing or replacing them. Fix-A-Floor is a simple DIY repair solution that is fast, easy and affordable, and surprisingly rewarding. If you can operate a drill, a caulking gun and mix a small batch of grout, you can do it. It works on all types of subfloor materials. Just Drill & Fill! Tip: For more precise application or smaller holes, you can include the 30 mL Adhesive Syringe with Blunt Tip Fill Needle when purchasing this product. It makes applying the adhesive cleaner and more accurate, especially in tight or narrow grout lines. The Nozzle The nozzle of the 300 mL Fix-A-Floor tube is specially engineered with a pre-drilled 3 mm hole to make it ideal for filling drilled holes in loose or hollow tile, marble and stone floors. It is firm enough to form a strong seal for optimal flow and complete coverage. Markings on the nozzle indicate cut points for 4.5 mm, 6 mm or any size you need, making it suitable for both narrow grout lines and wider applications. The Adhesive Fix-A-Floor Repair Adhesive is strong and flexible, featuring elastomeric bonding properties that prevent future issues caused by foundation movement, expansion and contraction of the subfloor or poor original installation. Used by flooring professionals for years, this product allows any homeowner to fix loose, hollow or squeaky tiles quickly and permanently. It is non-toxic, non-flammable and eco-friendly. Whether you are repairing a small area or a large floor section, Fix-A-Floor delivers lasting results and is guaranteed for the life of your floor. Just Drill & Fill! FAQs Q: Will Fix-A-Floor work with heated floors?A: Yes. Many customers use Fix-A-Floor over heated floor elements with no issues. Turn off the heating before, during and for 48 hours after applying. Q: Some of my grout is missing. Can I still use Fix-A-Floor?A: Yes. If small gaps or cracks exist, simply Drill & Fill. The adhesive will re-bond and stabilise loose areas. If the grout is completely missing, re-grout lightly, allow it to dry and then apply Fix-A-Floor. Q: Can I repair my whole floor or just one tile?A: Fix-A-Floor works on all sizes of problem areas, from a single tile to an entire room. It is suitable for all types of tile, marble and stone floors. Q: Can I use Fix-A-Floor outside?A: Yes. It performs well in both interior and exterior applications, including patios and decks. Q: Can I use Fix-A-Floor in showers or pools?A: No. It is not recommended for areas exposed to constant or excessive moisture. Q: Is Fix-A-Floor safe?A: Yes. It is a non-toxic, non-flammable, water-based adhesive that is safe and environmentally friendly. Q: Can I use it to re-glue a tile that has come loose?A: Yes. Apply Fix-A-Floor directly to the floor where the tile was, press the tile firmly into place, apply weight and allow to cure for 24 hours. Q: Do I need to place weight on the floor after filling?A: It is recommended to place some weight, such as a heavy object or bucket, on the area to aid curing and ensure even distribution. It is not mandatory but helps achieve optimal results. Q: What if adhesive does not appear from other holes?A: The adhesive may still be spreading beneath the tile. Move to the next hole and continue filling. Make sure you are not pressing the nozzle down onto the subfloor during application.
$39.95
![Sika SikaSeal Roof & Gutter Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9318324010461.png?v=1754724138&width=645)
![Sika SikaSeal Roof & Gutter Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324010454.png?v=1754724138&width=645)
SikaSeal® Roof & Gutter Silicone Sealant Product Type: 1-component neutral cure roof and gutter silicone sealant Product Overview SikaSeal® Roof & Gutter is a versatile, one-component, neutral curing silicone sealant designed for use in roofing and guttering applications. This sealant offers excellent adhesion to a variety of construction materials and is ideal for sealing roofs, gutters, and plumbing fixtures, both for exterior and interior applications. It cures quickly and provides a flexible, waterproof seal with superior temperature resistance. Key Features Neutral cure, low odour formula Excellent adhesion to common construction materials such as glass, metals, ceramics, tiles, plastics, concrete, and rubber Fast curing with a non-sag formula for easy application Interior and exterior use with a temperature resistance range of -40°C to +150°C High movement capability (±25% for translucent, ±50% for coloured variants) Waterproof seal for durable, long-lasting performance Non-toxic and water-potable approved per AS/NZS 4020:2018 Applications SikaSeal® Roof & Gutter is ideal for: Roof and gutter sealing Sealing polycarbonate roof sheeting General sealing around plumbing fixtures and penetrations Sealing interior and exterior joints Specifications Packaging 300ml cartridge Shelf Life 12 months (if stored properly) Colours Available Translucent, Grey, White, Black Density Translucent: ~1.02 kg/l, Colours: ~1.39 kg/l Shore A Hardness Translucent: ~26, Colours: ~46 Elongation at Break Translucent: ~250%, Colours: ~310% Movement Capability Translucent: ±25%, Colours: ±50% Service Temperature -40°C to +150°C Application Instructions Ensure the substrate is clean, dry, and free from oils, grease, dust, and other contaminants. For optimal adhesion, follow the recommended priming procedures based on the substrate type (non-porous or porous). Apply SikaSeal® Roof & Gutter using a sealant gun, ensuring full contact with the joint sides. Tool the sealant immediately after application for a smooth, durable finish. Important Considerations Do not apply on natural stone or bituminous substrates Not recommended for use under water pressure or in permanent water immersion Pre-test required on stressed polyacrylate and polycarbonate materials May cause discoloration on light-colored silicone when exposed to UV radiation (this does not affect the product's performance) Not suitable for use in confined spaces with no air circulation (requires atmospheric moisture to cure) Packaging & Storage Store in the original, unopened packaging in a dry location between +5°C and +25°C. Shelf life is 12 months from the production date under proper storage conditions. Contact & Ordering For more information or to place an order, contact us at admin@gluesaustralia.com.au
$13.00
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524002800_e901daee-d941-4c51-bb2c-fdfedd9a6316.jpg?v=1754711662&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$27.48
One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces 100% crystal clear / transparent Good workability Very good adhesion on many typical building materials Use: Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including: Plasterboard Wood surfaces Painted enamel Polyester Plastic Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions. CHARACTERISTICS AND ADVANTAGES 100% crystal clear / transparent Good workability Low shrinkage during cure Flexible and elastic Can be used on damp concrete Very good adhesion on many typical building materials COLOUR: Transparent Product Data Appearance / Colours Transparent Packaging 300 g cartridge (290 ml), 12 cartridges per box Storage Conditions / Shelf-Life Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met. Technical Data Chemical Base Silane terminated polymer Density 1.05 kg/l approx. (ISO 1183-1) Tensile Strength 2.0 N/mm2 approx. (ISO 37) Shore A Hardness 30 approx. (after 28 days) (ISO 868) Elongation at Break 400% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Service Temperature −40 °C to +70 °C SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department. Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly. Bonding After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again. Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear. Sealing After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.
$27.65
![Sikasil Pool Neutral-Cure Silicone Sealant 300 ml [White]](http://gluesaustralia.com.au/cdn/shop/files/Sikasil_pool_white.webp?v=1760227901&width=645)
Sikasil® Pool Neutral-Cure Silicone Sealant – 300 ml Cartridge Designed for use in demanding aquatic environments, Sikasil® Pool is a one-part, neutral-curing silicone sealant formulated specifically for swimming pools, wet areas, and permanently submerged joints. With exceptional resistance to chlorinated water, high elasticity, and outstanding fungal resistance, this sealant delivers durable, long-lasting performance. Key Features Excellent resistance to chlorinated water and common pool chemicals Movement accommodation of ± 25 % Neutral cure — non-corrosive, safe on most metals and tile systems High elasticity and recovery Very good resistance to fungal attack Suitable for interior and exterior applications Typical Applications Underwater joints in swimming pools Wet areas, such as spas, splash zones, and shower recesses Sealing between tiles, concrete, glass, and metal substrates Technical Highlights Service temperature range: –40 °C to +80 °C Shore A hardness (28 days): ~20 Elastic recovery: > 90% Typical curing speed: ~2 mm per 24 h Skinning time: ~5 minutes (23 °C / 50% RH) Available in White, Grey, and Transparent shades Shelf life: 15 months (when stored unopened between 5 °C and 25 °C) Usage & Application Tips Ensure surfaces are clean, dry, and free from contaminants (oil, dust, grease). Roughen smooth, non-porous surfaces (e.g. metal, glazed tile) before application. Use appropriate primers (e.g. Sika Aktivator-205, Primer-3 N) on metals, PVC, or porous substrates as recommended. Apply a closed-cell foam backing rod to control joint depth. Insert sealant by cartridge gun, avoiding air entrapment. Tool the bead within the skin formation time. Allow full cure (minimum 7 days) before filling pool with water. Limitations & Precautions This product is not suitable for: Joints in direct contact with potable food or drink Overpainting Use on substrates that leach oils, plasticisers or solvents (e.g. bitumen, EPDM rubber) Always consult the current Product Data Sheet (PDS) and Safety Data Sheet (SDS) for full technical, safety, and application details before use.
$24.50 $0.08/ml
![Sika Sikasil Pool Silicone Water Resistance [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/76128946_314287d6-23cc-4ab5-90d4-1c020429de31.png?v=1754711691&width=645)
$25.50
![Sika SikaSeal Gap Filler Acrylic 100 Sandable Paintable [White]](http://gluesaustralia.com.au/cdn/shop/files/9318324010676_f8ac62bc-ef55-4a57-a739-47528a1aae8c.jpg?v=1754711697&width=645)
DESCRIPTION SikaSeal® Acrylic 100 is a flexible, one component, water based acrylic joint sealant and gap filler where low demand of elongation are required, for interior use. USES SikaSeal® Acrylic 100 is suitable for sealing low movement joints around: ? brick ? Concrete ? Plasterboard ? Windows ? Doors ? Ceramic tiles SikaSeal® Acrylic 100 fills cracks and adheres to: ? Glass ? Wood ? Aluminium ? Brick ? Concrete ? Plasterboard ? Ceramic ? Painted surfaces. CHARACTERISTICS / ADVANTAGES Excellent adhesion to most common construction materials. Water clean-up of uncured sealant. Can be sanded back once fully cured if required to give smooth surface finish. Can be painted over using water based paints. Non-toxic
$6.50
SikaBond®-145 SuperGrip Premium polyurethane construction adhesive with fast build up of Strength SikaBond®-145 SuperGrip is a premium grade one-component polyurethane construction adhesive with good initial grab and high strength after 30 minutes^. SikaBond®-145 SuperGrip is a versatile, ready to use, fast curing, general purpose construction adhesive suitable for interior and exterior use. One-component. Interior & exterior. Non-shrink. Usage SikaBond®-145 SuperGrip is suitable for use in construction and repair applications where a permanent strong bond is required between porous-nonporous surfaces. SikaBond®-145 SuperGrip is suitable for bonding most common construction materials such as: Wood MDF Concrete Brick Metal Polystrene Polyurethane foam Some PVC Marble Granite Ceramic LOSP Timber Advantages One-component. Interior & exterior. Non-shrink. Non-sag. High initial grab. Adheres rapidly. Stong bond in 30 minutes^. Fast cure. Solvent-free. Resistant to heat. Resistant to weathering. Water resistant -D4 according to DIN En 204 Applies white, can dry translucent if applied in thin layers.
$24.15
SikaBond®-115 Max Tack is a 1-part construction adhesive with high final strength, designed for bonding most construction material substrates. It is suitable for internal and sheltered outdoor use. Key Features: Easy to apply Easy to clean Rapid build-up of strength High final strength Very low emissions (Acrylic dispersion) Applications: Ideal for bonding various construction components, including: Skirting boards Wooden frames Battens Mouldings Panels Terracotta tiles Anodised aluminium Polystyrene mouldings and ceiling tiles Bonds well to materials like: Concrete Mortar Fibre cement Wood Painted surfaces Shelf Life & Storage: Shelf life: 18 months from production date. Storage conditions: Store in original, unopened, undamaged packaging in a dry environment, at temperatures between +5°C and +25°C. Technical Details: Density: ~1.40 kg/l (ISO 1183-1) Application Instructions: Follow standard building and construction practices when applying SikaBond®-115 Max Tack. Substrate Preparation: Ensure the substrate is clean, sound, dry, and free from contaminants like oil, grease, cement laitance, old sealants, and loose paint. Remove dust and friable material through wire brushing, grinding, sanding, or other mechanical methods. For best results, follow these priming and pre-treatment steps: Non-Porous Substrates: For surfaces such as aluminium, anodised aluminium, stainless steel, PVC, and glazed tiles: Slightly roughen the surface using a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Wait 15 minutes before applying adhesive (within 6 hours). For metals like copper, brass, and titanium-zinc: Clean and pre-treat using Sika® Aktivator-205. After 15 minutes, apply Sika® Primer-3 N by brush. Wait at least 30 minutes (within 8 hours) before applying adhesive. Porous Substrates: For concrete, aerated concrete, mortars, and bricks: Prime the surface with Sika® Primer-3 N. Wait at least 30 minutes (within 8 hours) before applying adhesive. Note: Primers are adhesion promoters and are not a substitute for proper surface preparation. They also enhance the long-term bond strength. Cleaning of Tools: Clean tools and equipment immediately after use with Sika® Remover-208. For skin cleaning, use Sika® Cleaning Wipes-100. Once cured, the adhesive can only be removed mechanically. For more information, please consult Sika Technical Services.
$17.40
![Selleys No More Gaps Bricks & Mortar x 440g [Terracota]](http://gluesaustralia.com.au/cdn/shop/files/81ee53b7eade4c22a1268e1a28879d4e.jpg?v=1757753123&width=645)
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C. Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$22.00
SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to respond to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces How to use this product Ensure the surfaces to be bonded are clean, dry and free from dust, grease, oil and loose powdery materials. If porous surfaces are greasy or dirty, we would recommend cleaning the surface with SELLEYS LIQUID SUGAR SOAP, and allow to dry. If the surface is non-porous eg glass or metal, firstly clean the surface with Mineral Turpetine and then again with Methylated Spirits, and allow to dry. If there is old difficult to remove residue such as old flaky paint, we recommend using paint stripper such as SELLEYS KWIK STRIP SMART, and allow to dry. On wet timber pooled water should be wiped off. Highly oily timber types may need to be wiped with solvent prior to application to remove surface oils. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/ Course grain, as the construction adhesive will adhere more readily to a scratched up surface. Cut the seal at the top of the cartridge. Cut the nozzle end to desired opening (approx. 5mm diameter). Fit to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of work which requires a caulking gun. Apply a bead of product along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. Fix the surfaces with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. The product is repositionable for up to 20 minutes after fitting. Allow the adhesive to set (at least 24 hours) before removing any temporary fasteners or clamping. For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-5 minutes before firmly joining. The time it takes to form a strong bond depends on the nature and conditions of the application. In most situations strong bonds can be achieved after 24 hours and will continue to strengthen over a 2-3 day period. The product will fully cure up to 7 days. When the product is still wet it can be removed with mineral turpetine, otherwise if the product is dry it can be removed by sanding or scraping, we recommend using a 50mm ROTA COTA Soft Grip Scraper. Clean any excess from your hands with SELLEYS Hand Kleen Wipes. To eliminate squeaks in tongue and groove flooring, apply a bead of Liquid nails into the groove or each board when installing. Handy tips When applying to one surface, ensure sufficient LIQUID NAILS Original is used so that some adhesive extrudes out when surfaces are brought together then wipe off excess if necessary. If glue is not visible, then insufficient contact may not have been made between the surfaces and a weak joint may result. LIQUID NAILS Original should always be used in conjunction with mechanical fasteners in structural, critical or high stress applications. LIQUID NAILS Original is sometimes called LIQUID NAILS (SOLVENT) to differentiate it from the other Liquid Nails products. LIQUID NAILS Original shrinks slightly on curing. Cured LIQUID NAILS Original residues can be removed by holding a rag soaked in Mineral Turps against the residue, then rubbing the residue once softened. Mineral Turps penetrates in this way at approximately 1 mm per hour. When Liquid Nails Original joints are directly exposed to the weather, it is recommended to seal around the edges with a silicone sealant to prevent water ponding inside the joint and thus weaken the joint. LIQUID NAILS Original is NOT recommended for use on mirrors or polystyrene. Use LIQUID NAILS MIRROR METAL GLASS for mirrors and LIQUID NAILS FAST for polystyrene. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job.
$5.00
Liquid Nails Fast is a water-based high strength (*) construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. After drying it is beige (light tan) in colour. UsesLiquid Nails Fast has high initial (immediate) grab which reduces the need to support joins while the adhesive cures. The initial grab works best with porous surfaces. It will bond to many building materials including MDF, particle board, timber, plaster board, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results are achieved when at least one surface is porous. Liquid Nails Fast would typically be used for the following applications: Areas where nailing is not desirableSkirting boards, architraves, cornicesWall panelling to masonryStyrene foam to metal roofing Technical FeaturesFast grab – high initial holding minimises slippage when adhering on vertical surfacesMeets or exceeds AS 2329-1999 (Mastic adhesives for fixing wall boards)Does not drip, sag or string between panelsBridges gaps and will adhere materials with uneven surfacesLow mess – excess and squeeze out is easily cleaned up with wet clothNo solvent fumes – ideal for large indoor jobsHigh flexibility – will withstand thermal movement and vibrationHigh heat resistance – will not lose bonds exposed to sunPaintable when dryEasy to extrude at all temperatures Application TipsLiquid Nails Fast should always be used in conjunction with permanent mechanical fasteners except in low stress applications such as wall panelling and fixing light weight objects. (Bonds may creep under constant heavy loads.)Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications.In cold or damp weather and between non-porous materials drying time is greatly extendedThick applications take longer to dry than thin applicationsPre-test plastics to determine suitable bonding. Adheres well to UPVC. Not suitable for polyethylene and polypropylene. For wood flooring applications Liquid Nails (solvent based) is recommended. [Liquid Nails Fast is satisfactory for fixing sheet flooring (particleboard/ply) to joists in conjunction with the manufacturer’s minimum nailing specification but is not recommended for fixing sheet wood flooring to flat surfaces such as existing or concrete floors. Technical Details and PerformanceFor porous substrates good bond strength is achieved after 24 hours and will continue to strengthen over 2-3 day period. Time for strong bond depends on nature and conditions of application. In cold or damp weather and between non-porous materials, drying time is greatly extended. Indicative information only, not to be used for setting specifications. AppearanceLump free, air-free smooth beige paste Specific GravityApprox. 1.44g/mL @ 25oC ViscosityTypical 7000 – 9000 Poise SlumpTypical: 0mm Shear Adhesion Strength (7 days) (AS2329)Greater than 1500kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure)Typical 40N/25mm (wire gauze off hoop pine.(Variant to AS2329)) Initial Bond Strength AS2329-1999D (Tested after 24 hrs)Over 200kPa Heat ResistanceBonds will resist temporary exposure to temperatures up to 140oC. Constant high temperatures will reduce constant load holding power (see below). Creep resistance (under constant load)*2Fully cured *1 bonds of 625 sq. mm will hold up to 500g loads (7.8kPa) in shear at constant 80oC Fully cured *1 bonds of 625 sq.mm will hold up to 100kPa in shear at 25oC (equivalent to 6Kg load on 625 sq.mm bond area) Coverage15 metres of a 5mm diameter bead 1mm thick bonds on porous substrates cured at least 7 days at temps above 25oCThis data is provided as indicative only. Not to be used for design purposes. Thick bonds reduce constant load holding power and increase curing time. Larger bond areas increase curing time. CleaningLiquid Nails Fast may be cleaned off with hot soapy water or a damp cloth while still wet. Dry adhesive is best removed by scraping or peeling.
$7.00
Crystal clear Can be used even on damp/wet and impervious surfaces. Closest you will get to a transparent Ritetack 290ml tube Used indoors and outdoors as long as not exposed to UV. Clear adhesive Invisifix is a versatile 290ml tube of clear construction adhesive that lets you see exactly what you’re gluing. A quick, easy-to-use, water-friendly clear construction adhesive allows you to see exactly what you’re gluing. Reasons why to use Invisifix The excess clear construction adhesive always finds a way to make itself noticeable. Sometimes it is even difficult to remove it. With Invisifix, you don’t have to worry about unaesthetic colours since it is literally see-through! Amazing fast grab! That means no time wasted holding things into place while you wait for them to adhere. With Invisifix, you apply it to the surface, and it immediately sticks! Invisifix is water-friendly, so no more breaking a sweat while trying to dry surfaces before applying. This comes in handy if you’re thinking of applying Invisifix Clear Adhesive in areas prone to humidity and dampness, like bathrooms, pool areas, or kitchens. This adhesive can stretch up to 375% from its original size, and that’s important if you want some flexibility in your adhesion. That means that sudden movements like some impact won’t compromise the integrity of your adhesive and of whatever it is holding. Not only does Invisifix work on virtually any surface, but it also won’t stain any of them, including the porous ones, like a stone!
$9.95
![Poly Gap Filler Sealant Multipurpose [White]](http://gluesaustralia.com.au/cdn/shop/files/9311531000683_aaee7eb0-0b5d-4d11-8699-1eea1db48c2c.png?v=1754712208&width=645)
A flexible multipurpose gap filler, to fill gaps around cornice, wall joints, skirting board, window and door frames where where movement causes ordinary fillers to crack or fall out. For use on: Wood, brick, aluminium, glass, plasterboard, ceramic tiles and painted surfaces (INTERIOR & EXTERIOR) Coverage: 30m/3mm bead. Dry time: Skins in 30 minutes at 25°C. Full cure in 7days. Ready to use: YES Available in: 475g Colour: White NOTE: Not for fine joints between tongue and groove boards or weatherboard overlaps. • Ensure surfaces are clean, dry and free from oil, dust, grease, flaking paint and old sealant. • Using caulking gun, push sealant ahead of nozzle forcing it onto the surface and into the joint. Ensure the sealant is touching both sides of the gap. • Smooth with wet finger or knife and remove excess sealant immediately with a damp cloth. • Allow sealant to skin approx 30 min before painting with water-based paints. • Allow to set for 48 hours if using oil based paint or if joint is large. • Some water-based undercoats and flat paints may crack on drying. Test a small section of sealant. Paint cracking may be reduced by using a vinyl/ acrylic semi glossed paint or oil based undercoats first, or by allowing the sealant to cure thoroughly before painting. • Do not use outside if rain is imminent, not for contantly damp areas. • Painting improves exterior durability. • Use Poly silicone sealants for a watertight seal or where movement is excessive. • Water clean up Q. How do I fill gaps between my wooden window frames and inside wall? A. You're dealing with two different materials here, plaster and wood. To allow for differential movement between them, use Polyfilla Gap Filler, wiping off any excess with a damp cloth. Q. I painted over the areas where I used Polyfilla Gap Filler and now cracks have appeared. Why has this happened? A. If the gap filler was not cured sufficiently before it was painted over, cracks can occur as the gap filler shrinks. To prevent this, allow 48 hours drying time when you are filling large gaps or painting with oil-based paints. Also, some water based undercoats and paints shrink during drying and as Polyfilla Gap Filler is flexible, it won't stop cracks appearing in the shrinking paint on its surface. Test the paint on a small section of gap filler and if this is a problem you can reduce cracking by allowing the filler to cure thoroughly or by first coating it with a vinyl/acrylic semi-gloss or oil-based undercoat. Q. Why does my gap filler keeps cracking? A. It is important to remember that the width of a gap affects how much the product can move. Fine cracks less than 2mm allow the gap filler to move only very tiny amounts before it may crack again. It is best to ensure that you have at least 3mm worth of product so you can maximise the movement capability of your joint.
$5.00
![Parfix Roof Gutter Concrete Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697115768_c056520c-16e5-4bd6-9d65-de084d15ff93.jpg?v=1754712245&width=645)
Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
$9.35
Parfix Maxi Nails 300g: The Ultimate Multi-Surface Construction Adhesive Key Features High-strength bond suitable for a variety of applications Paintable for aesthetic versatility Effective both indoors and outdoors Specifications Colour: Beige Model Name: Parfix 300g Maxi Nails Construction Adhesive Material: Polymer Dissolved in Hydrocarbon Solvent Outdoor: Yes Indoor: Yes Why Choose Parfix Maxi Nails 300g? Designed to handle a multitude of construction challenges, Parfix Maxi Nails 300g provides a robust bond that lasts. Whether you're working indoors or taking on external projects, this adhesive is formulated to give you the results you need.
$4.19
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/9310492265001_6fb5fccc-7784-41bb-9997-bbd917e3c834.png?v=1754712704&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$22.51
Bostik Seal it Kitchen & Bathroom Light Grey: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Dunlop Tile-All Plus Premixed Tile Adhesive 310ml Tile-All Plus is a single component, silane modified polymer adhesive and neutral curing sealant. It offers high initial tack, strong bonding and excellent flexibility. Use it for fast, reliable repairs in showers, kitchens and bathrooms, for replacing tiles, fitting accessories and finishing joints. It can even be used for minor repairs underwater. Why you will like it High initial grab for confident positioning Flexible bond that resists movement and vibration Neutral cure for a low odour application experience Works as both an adhesive and a sealant Paintable after drying with most common paints (test first) Where to use it Showers, kitchens and bathrooms Replacing loose tiles and fitting trims or accessories Finishing expansion and connection joints Minor underwater fixes on suitable surfaces Suitable materials Glass, tiles, ceramics, timber, plastics, metals, concrete, wall panels, waterproofing membranes, aluminium, polystyrene foam, and glazed tiles. Always ensure surfaces are sound, clean and free from dust, oil, grease and coatings. Slightly damp substrates are acceptable. How to use Remove the aluminium seal at the base of the cartridge. Pierce the inner membrane, fit the nozzle and trim to the required bead size. Apply in stripes to the substrate or the item being fixed. Press parts together firmly within 7 to 10 minutes at 20°C, before skinning begins. For spot fixing, keep glue points 25 to 30 cm apart and confirm the item weight is appropriate. Avoid application below 5°C or above 35°C. Good to know Open time varies with temperature, humidity and substrate. Higher humidity shortens open time. If reusing, remove any skinned layer from the nozzle before the next application. Spills can be wiped away while wet with a clean cloth. Not recommended for chemical resistant applications. Cleanup and storage Clean excess while wet with a cloth. Shelf life is up to 12 months in unopened packaging stored in a cool, dry place at around 23°C and 50 percent relative humidity. Safety Use in a well ventilated area. Avoid skin and eye contact. If contact occurs, flush eyes with water for at least 15 minutes and seek medical advice. Wash skin with soap and water. If inhalation discomfort occurs, move to fresh air. If swallowed, drink water in small portions and seek medical advice. Keep out of reach of children.
$27.98
SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to response to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces
$17.49
Selleys 635 Multipurpose Elastic Sealant Clear 290 mL Selleys 635 is a premium 100 percent clear elastic joint sealant that delivers strong, flexible and waterproof seals for indoor and outdoor jobs. Powered by hybrid technology, it adheres to most common building materials without primer and resists UV and weather for long lasting performance. Paintable with water based paints after skinning. Why you will love it Crystal clear finish that stays clear Excellent weather and UV resistance for exterior use Primerless adhesion to most surfaces Adheres to damp or wet surfaces Non slumping in joints up to 20 mm Low odour and low VOC, solvent and isocyanate free Paintable with water based paints once skinned Where to use Vertical and horizontal joints on most indoor and outdoor surfaces, including concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles, glass and many other common building materials. Not suitable for Polyethylene, Polypropylene or PTFE, structural glazing, or permanent water immersion. Directions Prep Clean and remove dust, grease and contaminants. Degrease metals. Cut nozzle on a sharp angle slightly wider than the joint. Use a suitable backing rod to control depth where required. Apply Gun the sealant into the joint. Tool within 10 minutes to ensure good contact with joint sides. Paint When skinned, paint with water based paints. For solvent based paints, first apply a water based undercoat and test on a small area. Clean up Clean spills and tools with mineral turps before cure. Once cured, remove mechanically. Storage Store below 30°C in a cool, dry place Unopened shelf life 12 months from date of manufacture Technical details Technology Moisture curing silyl modified polymer Colour Clear Packaging Cartridge 290 mL Density Approx. 1.05 g per mL Skin time at 23°C and 50 percent RH About 45 minutes Tack free time at 23°C and 50 percent RH About 60 minutes Cure rate at 23°C and 50 percent RH 2.5 to 3.5 mm per 24 hours Shore A hardness 35 ± 5 Tensile strength 1.7 MPa Elongation at break 240 percent Movement capability ± 12.5 percent Application temperature 5 to 35°C Service temperature ?20 to 70°C VOC content Approx. 35 g per L VOC classification Meets Green Building Council of Australia limits for general purpose and architectural sealants Good to know Better extrudability and curing from 5°C and above Non bubbling and non slumping formulation Sandable when fully cured Limitations Not for permanent water immersion Not for Polyethylene, Polypropylene or PTFE Not for structural glazing Follow all safety directions. For first aid and handling information refer to the product SDS.
$20.74
Bastion Bond Breaker Joint Sealant Professional silicone bond breaker for wet areas. Create a flexible, waterproof separation at wall to wall and wall to floor junctions so your membrane and tile system can move without cracking. Ideal for bathrooms, showers, laundries and balconies. Why choose this sealant Permanently flexible to absorb movement in corners and junctions Neutral cure silicone suitable for use with most waterproofing membranes Low odour, low VOC, indoor use friendly Excellent adhesion to common building materials including concrete, masonry, ceramic tile, porcelain and most metals Water resistant once cured and designed for wet area applications Easy to gun out and tool for a smooth finish Typical uses Forming a bond breaker fillet in shower bases, bathrooms and laundries before waterproofing Movement joints at internal corners prior to tiling General wet area sealing where a flexible joint is needed Surface preparation Ensure surfaces are clean, dry and free from dust, oil, loose material and old sealant. Mask adjacent edges for a neat finish if required. For wide gaps, insert backing rod to control sealant depth. How to apply Cut the cartridge nozzle to the desired bead size and load into a standard caulking gun. Gun a continuous bead into the corner or joint. Aim for a smooth cove fillet in the 5 to 12 mm range. Tool the bead with a spatula or rounded tool to compact and shape it. Remove masking tape while the sealant is still wet. Allow the bond breaker to skin before applying compatible waterproofing membranes over the area. Follow your membrane manufacturer’s recoat time. Cure and finishing Skin time is typically minutes depending on temperature and humidity. Full cure occurs over 24 to 48 hours for standard beads. Thicker sections require longer. After the membrane has cured, complete tiling and finish perimeter joints with a sanitary grade silicone. Clean up Wipe away excess immediately with a clean cloth. Once cured, remove mechanically by trimming and peeling. Handy tips Not paintable. If painting is required, paint adjacent surfaces before sealing. Always use backing rod for large joints to control sealant depth and reduce three sided adhesion. Pre test on sensitive or natural stone surfaces. Do not use in continuously immersed conditions or for structural glazing. Storage and packaging Cartridge size: 300 mL Store upright in a cool, dry place. Use before the best by date printed on the cartridge. Safety Use in a well ventilated area. Avoid contact with skin and eyes. Keep out of reach of children. Refer to the product label for first aid directions. In the box 1 x 300 mL cartridge of Bastion Bond Breaker Joint Sealant 1 x application nozzle
$10.85
Dunlop FC Joint Sealant Dunlop FC Joint Sealant is a premium, ultra flexible, moisture curing polyurethane sealant designed for jointing fibre cement, blueboard and compressed fibre cement sheets. The non slump formula handles joints up to 40 mm wide with a movement capability of plus or minus 25 percent. It is easy to apply, solvent free and isocyanate free. Colour: Grey. Why choose this sealant High flexibility for dynamic joints Non slump for clean, accurate beads on vertical and horizontal surfaces Solvent free and isocyanate free Paintable after curing Reliable performance supported by a 10 year guarantee Ideal uses Joints in fibre cement, blueboard and compressed fibre cement sheets Facade and cladding joints where movement is expected General building joints up to 40 mm width Compatible surfaces Adheres to most common construction substrates, including: Fibre cement sheets and blueboard Precast concrete panels, blockwork and bricks Sandstone and granite Fibreglass Plasterboard Technical details Movement capability ± 25% Joint width Up to 40 mm Skin time Approximately 35 minutes at 23°C and 50% RH Tack free time Approximately 1 hour at 23°C and 50% RH Cure rate About 2.5 mm per 24 hours at 23°C and 50% RH Application temperature 10°C to 35°C Clean up Warm water immediately after use Shelf life 12 months unopened, stored cool and dry Finish Paintable when dry. Can be overcoated with paint or texture coats. Colour Grey Surface preparation Ensure surfaces are clean and dry, free of dust, oil, grease, salt, mould, release agents and any contaminants that may affect adhesion. Mask adjacent areas to keep lines neat. Follow sheet fixing instructions from the board manufacturer. How to apply Cut the nozzle at a sharp angle slightly wider than the desired bead or joint width. Use a suitable backing rod where required to control depth. Aim for a joint depth equal to half the joint width. Gun the sealant into the joint and tool within 10 minutes using a round spatula to ensure full contact with the joint sides. Curing times increase in cold or humid conditions. Safety and handling Avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection. Ensure adequate ventilation during application. Keep out of reach of children. Refer to the product SDS for full safety guidance. Guarantee Backed by a 10 year guarantee when used as directed.
$21.58
Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
$46.22
High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. Safety Tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
$47.44
Crommelin Hybrid MS Polyurethane Flexible Sealant 300ml Take on interior and exterior sealing with a professional grade hybrid MS polyurethane. This single component sealant delivers a flexible, durable seal on common building substrates and is suitable for a wide range of construction and maintenance tasks. Key benefits Very low VOC and isocyanate free UV resistant for long term outdoor performance High flexibility to accommodate joint movement Excellent adhesion on properly prepared porous and non porous surfaces Easy to gun, tool and clean up Typical applications Construction and expansion joints Perimeter sealing around windows and doors Roofing and cladding laps, flashings and penetrations General gap sealing in wet and dry areas Suitable substrates Concrete, masonry, brick and render Timber and fibre cement Metals and coated metals Many plastics* and glass *Always pre test for compatibility and adhesion. Surface preparation Surfaces must be clean, dry, sound and free of dust, oil, release agents and loose material. Remove old sealant and contaminants. Abrade dense or glossy surfaces if required. Use suitable primer if specified for difficult or highly porous substrates. Mask edges for neat joints and install closed cell backing rod where needed to control joint depth. Application Cut nozzle to required bead size and load cartridge into a quality caulking gun. Gun a continuous bead into the joint ensuring full contact with sides and backing. Tool off with a moistened spatula for a smooth finish before skin forms. Protect from water and disturbance during initial cure. Clean up Clean tools and fresh spills promptly. Once cured, remove by mechanical means. Good to know Low odour formulation suitable for indoor use with ventilation. Paintable with many water based coatings once skinned and cured. Always test first. Store upright in a cool, dry place. Keep out of direct sunlight. Safety Wear suitable gloves and eye protection. Avoid contact with skin and eyes. If contact occurs, rinse with clean water. Refer to the product Safety Data Sheet for full precautions. What’s in the box 1 x 300ml cartridge 1 x application nozzle
$15.15
Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load): – At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area – At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.
$143.34
Poly Ultra Nails Construction Adhesive is a high strength, versatile adhesive designed for bonding a wide range of building materials both indoors and outdoors. It offers exceptional adhesion, easy application, and water resistance, making it a reliable choice for construction and renovation projects. Features High strength bonding suitable for multiple materials Repositionable for up to 20 minutes for precise alignment Waterproof once cured Ready to use straight from the cartridge Brown finish for a natural look Suitable Materials Concrete, brick, plasterboard, ceramics Plywood, particle board, aluminium Hardwood, softwood, steel, fibreglass Some plastics (pre-test recommended) Application Instructions Ensure surfaces are clean, dry, and free from dust, grease, or flaking paint. Cut the seal, fit the nozzle, and cut to the desired bead size. Insert into a caulking gun. For wall panelling and sheet flooring, apply 6mm beads along studs or joists in a zig-zag line at 40cm intervals. Bring surfaces together within 10 minutes and press firmly along glue lines. Reposition if needed within 20 minutes. Fix with nails, screws, or clamps for at least 24 hours to ensure bond strength. For contact bonding, apply to one surface, bring together, then separate for 3–5 minutes before rejoining. Clean tools and excess adhesive with mineral turpentine. Technical Information Coverage: Approximately 15 metres of 5mm bead Initial bond: Within 24 hours at 25°C Full cure: Up to 7 days Colour: Brown Important Notes Not suitable for mirrors, polystyrene foam, or continuous water immersion Avoid use on copper-based metals or metals exposed to direct sunlight heat Do not use for tightly clamped joints or heavy loads without mechanical fasteners Safety Information Use in a well-ventilated area and avoid breathing vapours Wear protective gloves and eye protection Keep away from heat, sparks, and open flames Keep out of reach of children If swallowed, do not induce vomiting — contact a doctor or Poisons Information Centre (AUST 131 126; NZ 0800 764 766) Contains 30% w/w liquid hydrocarbons
$4.85
Dunlop Roof Repair Waterproofing Adhesive 310ml Seal, stick and stop leaks on the spot. This highly flexible, silane modified adhesive and sealant bonds and seals even in wet conditions, making it a smart fix for urgent roof, gutter and pond repairs. Why you will love it Works in the wet and can be applied underwater for minor repairs Flexible waterproof seal for joints, cracks and patches Strong adhesive grab for quick spot fixes Paintable once cured to match surrounding surfaces Low mess clean up while wet Ideal surfaces Concrete, wall panels, timber, waterproofing membranes, ceramic tiles, aluminium, plastics, metal, polystyrene foam, glass and glazed tiles. Typical uses Emergency roof and gutter leak sealing Sealing laps, flashings and penetrations Pond edge and minor underwater touch ups General crack and joint sealing around the home Spot fixing where fast, reliable adhesion is needed Directions Prep: Ensure the surface is firm and free of dust, oil and loose residues. Slightly damp surfaces are acceptable. Load: Remove the aluminium seal, pierce the nozzle membrane, fit and trim the nozzle, then place the cartridge in a caulking gun. Apply as a sealant: Gun a continuous bead over the joint or crack and allow to cure. Apply as an adhesive: Gun bead lines or spots, then press parts together within 7 to 10 minutes at 23°C, before skinning starts. For spot fixing, keep glue points 25 to 30 cm apart. Clean up: Wipe away any excess while wet with a clean cloth. Good to know Application temperature: 5°C to 35°C Dry and cure times vary with substrate and climate. Higher humidity shortens open time, lower humidity extends it. Colour: Grey. Can be over painted once dry. Always test paint compatibility on a small area first. Shelf life: 12 months in unopened packaging stored in a cool, dry place Packaging: 310 ml cartridge Safety Wear gloves and eye protection. Avoid inhaling vapours and ensure good ventilation. If in eyes, rinse with running water and seek medical advice. Keep out of reach of children. Warranty Backed by a 10 year product guarantee when used as directed. This is in addition to your rights under the Australian Consumer Law. Notes Do a trial application for underwater or constantly wet repairs, as long term stability depends on the specific situation. Not for chemical resistant applications. Remove any skinned layer in the nozzle before reusing an opened cartridge.
$21.97
Sika AnchorFix-1 Grey Structural Adhesive 300 ml Overview Sika AnchorFix-1 Grey Structural Adhesive 300 ml is a high quality chemical anchoring adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials concrete masonry natural stone hollow substrates with sleeves Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Observe minimum bond and substrate temperatures specified by the manufacturer. Keep resin warm in cold weather. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Cure time depends on substrate temperature. At 20°C typical cure is within a few hours. Do not load anchors until fully cured. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Wipe uncured resin with appropriate solvent. Once cured, it is chemically resistant and must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$34.90
Tuff Turf Synthetic Grass Adhesive 320 g Overview Tuff Turf Synthetic Grass Adhesive 320 g is a high quality synthetic grass adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials synthetic turf backing seaming tape concrete compacted base plywood Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Install in dry conditions between 10°C and 30°C, avoiding heavy dew or rain. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Working time varies with conditions. Allow sufficient cure before foot traffic. Full strength typically within 24 to 48 hours. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean tools while wet with a suitable solvent or soapy water depending on formulation. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$12.76
Sikaflex 258 Primerless Glass Adhesive 310 mL is a reliable polyurethane glass adhesive designed for primerless bonding to suitable automotive glass chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 310 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Sikaflex 258 for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Sikaflex 258 Primerless Glass Adhesive 310 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bonding glass where a primerless system is specified Automotive and transport glazing carried out by trained users Suitable surfaces The adhesive works well on the following surface types when properly prepared: Compatible glass substrates Painted frames and prepared bodywork per Sika guidance Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of observe skin time and install components within this window. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Moisture cure technology forms a strong, elastic bond. Skin forms first, followed by through cure depending on joint depth and humidity. Temperature and environmental performance Do not apply below the minimum stated on pack. Maintain adequate humidity for moisture cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Remove fresh adhesive with suitable cleaner. Once cured, trim with a sharp blade using care. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store cartridges cool and dry. Check use by dates before installation in critical work. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$37.49
Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load):– At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area– At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.
$21.74
![Sika Sikaflex Pro+ Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$24.00
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Black]](http://gluesaustralia.com.au/cdn/shop/files/2330c4b4af69418ba74ba7691a5becd0.jpg?v=1757756157&width=645)
Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
$0.00 - $17.00
SikaSeal® Kitchen and Bathroom SikaSeal® Kitchen and Bathroom is a one-component, neutral-curing, low-odour silicone sealant with excellent adhesion and a long shelf life for DIY applications. It cures at room temperature under the action of atmospheric moisture to give a permanently flexible silicone rubber. Uses Glass and enamel Ceramics and tiles Aluminium, steel, zinc, copper Plastic laminates Rubber Stainless steel Concrete and grouts Characteristics / Advantages Excellent adhesion Great weatherability Non-sag Great tooling characteristics Long-term mould resistance Interior and exterior usage Fast curing Colours White Beige Black Charcoal Transparent Alabaster Almond Ivory Off White Stone Pewter Grey Mid Grey Stone Brown Packaging 300ml cartridges, 12 cartridges per box Shelf Life 12 months from the date of production if stored in undamaged and unopened original sealed containers, in dry conditions, and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base: Neutral curing Density: 0.98 g/cm³ @ 23ºC Skin/Forming Time: 10-15 minutes @ 23ºC/50% r.h. Curing Rate: 72 hours @ 23ºC/50% r.h. Consistency: Non-sag Mechanical/Physical Properties Tensile Strength: 0.4 N/mm² @ 23ºC/50% r.h. Shore A Hardness: 20 SHA E-Modulus: 0.30 N/mm² at 10% elongation @ 23ºC/50% r.h. Ultimate Elongation: 300% Anti-mildew Property: 0 level
$0.00 - $14.00
![MaxisiL A Silicone Sealant [Colour: A28 Brown]](http://gluesaustralia.com.au/cdn/shop/files/693_720.jpg?v=1754724110&width=645)
![MaxisiL A Silicone Sealant [Colour: A29 Havana]](http://gluesaustralia.com.au/cdn/shop/files/9326816000715.jpg?v=1754724111&width=645)
The Premium Wet Area Sealant Wet areas Baths, showers, toilets Easy to use Contains strong fungicides to fight mould Maxisil A Ceramic Silicone is an acetic cure silicone recommended for all ceramic tile areas, especially for expansion joints in bathrooms, kitchens, and flooring sectors. Built-in fungicides for mould resistance For both exterior and interior use Excellent weatherability, resistant to ageing and UV radiation Resistant to chemicals and temperature Primerless adhesion to clean, dry surfaces such as ceramics, glass, acrylics, aluminium, and painted wood Very good tooling and smoothing properties Time-saving with an easy cleanup system Please note that colour samples are not true to the actual colour. This is a guide only. Characteristics 1-component acetate-curing silicone sealant Excellent weathering, ageing, and UV resistance Enables a great finish, will not string during application Good tooling and smoothing properties Contains fungicides Medium skin formation time for easy handling Very good adhesion on ceramic substrates Primerless adhesion to many substrates Stress expansion modulus at 100% (DIN 53 504, S3A): 0.3 N/mm² Meets DIN 18545, part 2D (German industrial standard) Available in a variety of colours (custom colours available upon request) Fields of Application Sealing connection joints between ceramic tiles, showers, baths, and flooring sections Expansion/movement joints in bathrooms and wet areas Connection joints on door and window frames Sealing double-glazing joints Glass block glazing Sealing general building substrates Suitable for interior and exterior use Important Information Before application, ensure materials in the contact area are compatible with the sealant and with each other to prevent damage or discoloration. If in doubt, consult the manufacturers of surrounding substrates. While curing, small amounts of acetic acid are released — ensure good ventilation After curing, the product is odourless and harmless Thicker silicone layers require longer vulcanisation time Not for full-surface bonding unless construction prerequisites are met For layers over 15mm, contact our technical department Avoid contact with bitumen-containing materials or those releasing solvents (e.g. butyl, EPDM, neoprene, bituminous paints) When replacing mould-contaminated joints, remove all old sealant and treat areas with Maxisil Anti-Mildew Spray Technical Properties Skin-forming time (23°C / 50% RAH) ~ 15 min Curing in 24h (23°C / 50% RAH) ~ 2–3 mm Processing temperature +5°C to +35°C Viscosity (23°C) Pasty, stable Density (23°C, ISO 1183-1) ~ 1.0 g/cm³ Shore A hardness (ISO 868) ~ 20 Permissible movement capability —
$22.50
![Sika SikaSeal Flexible Gap Filler Super-200 Paintable [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/9318324010690_a135bef3-1e63-49fe-b52d-552f6c48153c.png?v=1754711651&width=645)
SikaSeal® Super-200 is great for sealing of connection joints with moderate movement Good UV resistance Low odour For exterior and interior use USE Sealing of connection joints with moderate movement around windows, window sills, doors, PVC pipes, dry partition walls and ceiling Filling of cracks on interior and exterior walls (with no permanent water immersion) CHARACTERISTICS AND ADVANTAGES For exterior and interior use High movement capability ±12.5% Good UV resistance Solvent-free, low odour Overpaintable Very good adhesion on most construction materials such as concrete, plaster, wood Possible storage at -10°C for short period of time (max 24h) Conforms to EN 15651-1 F INT EXT
$6.73
![Sika Sikaflex 252 High Strength Structural Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/7612895456188_c10ea96d-b0be-41ba-a0ee-9656fab35b16.jpg?v=1754711652&width=645)
Elastic adhesive for vehicle assembly bonding Sikaflex®-252 is an elastic 1-component polyurethane adhesive especially designed for bonding large components in vehicle assembly. It is suitable for bonding coated metal, GRP, ceramic materials and plastics. Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties PRODUCT BENEFITS Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties Can be painted Vibration-damping Electrically non-conductive Usage Sikaflex®-252 is suitable for assemblies that are subject to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminum (including anodized components), sheet steel (including phosphated, chromated and galvanized components), metal primers and paint coatings (2-component systems), ceramic materials and plastics. Seek manufacturer’s advice before using on plastics that are prone to stress cracking. This product is suitable for professional experienced users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
$53.62
Premium one component room temperature vulcanising silicone sealant USE Fridge and freezer sealing Pizza oven sealing Oven sealing Aluminium Glass CHARACTERISTICS AND ADVANTAGES High temperature resistance (-50 to 250OC) Excellent adhesion Gap filling properties Heat proof Vibration resistant Highly versatile PACKAGING: 300 ml cartridges COLOUR: Black SikaSeal® Appliance Silicone Sealant is a premium one component room temperature vulcanising (RTV) silicone rubber designed for flexible gasketing and sealing applications. SikaSeal® Appliance Silicone Sealant forms a tough but flexible seal of all shapes and sizes and fills any surface voids. The cured product can withstand vibration, weathering, temperature extremes, water oil and grease without hardening, shrinking or cracking. Uses Fridge and freezer sealing Pizza oven sealing Oven sealing Aluminium Glass Characteristics / Advantages High temperature resistance (-50 - 250°C) Excellent adhesion Heat proof Gap Filling properties Vibration resistant Highly versatile Product Data Colour Black Packaging 300ml Cartridge, 12 cartridges per box Storage 18 months from date of production if stored in undamaged and unopened original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base 1-C silicone Density (uncured) 1.0 kg/l approx. Skin Time 10 min approx. Tack-free time 20 min approx. Curing Time 24 hours approx. Cure Mechanism Moisture-curing Cure Type Acetoxy Application temperature 5 - 45°C Mechanical/Physical Properties Tensile Strength 1.0 N/mm2 approx. Shore a Hardness 25 approx. Ultimate Elongation 600% approx. Application Details Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue-free solvent and allowing drying properly. Cut the nozzle at a 45° angle to the desired bead size (3 mm is suitable for most applications) then apply a continuous and even bead along the joint. Cure Mechanism SikaSeal® Appliance cures by reaction with atmospheric moisture. The reaction thus starts at the surface and proceeds to the core of the joint. The curing speed depends on the relative humidity, temperature and thickness of the sealant. At low temperatures, the water content of the air is lower and the curing reaction proceeds more slowly. Clean Up Uncured, excess SikaSeal® Appliance may be removed with Sika® Remover-208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife. Application Conditions/ Limitations Restrictions On Use SikaSeal® Appliance is not recommended for use in applications where it will be permanently exposed to temperatures exceeding 250°C or in contact with fuels. The above information is offered for general guidance only.
$21.37
You have seen 48 out of 166 products
Standard cartridges for use with a caulking gun, ideal for beads along joints, seams and panels in bathrooms, roofing and construction. Choose non-sag or fast-grab for vertical work and cut the nozzle to match your bead size. Use filters to refine by chemistry, cure speed and temperature rating. Always review the product page and TDS/SDS for surface prep and cure guidance.
