Note: If you are working on a timber floor, you will need to use Fix-A-Floor Polyurethane for Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive, now patented, is an extra-strength bonding adhesive designed specifically for re-bonding loose and hollow tiles, marble and stone without the cost and mess of removing or replacing them. Fix-A-Floor is a simple DIY repair solution that is fast, easy and affordable, and surprisingly rewarding. If you can operate a drill, a caulking gun and mix a small batch of grout, you can do it. It works on all types of subfloor materials. Just Drill & Fill! Tip: For more precise application or smaller holes, you can include the 30 mL Adhesive Syringe with Blunt Tip Fill Needle when purchasing this product. It makes applying the adhesive cleaner and more accurate, especially in tight or narrow grout lines. The Nozzle The nozzle of the 300 mL Fix-A-Floor tube is specially engineered with a pre-drilled 3 mm hole to make it ideal for filling drilled holes in loose or hollow tile, marble and stone floors. It is firm enough to form a strong seal for optimal flow and complete coverage. Markings on the nozzle indicate cut points for 4.5 mm, 6 mm or any size you need, making it suitable for both narrow grout lines and wider applications. The Adhesive Fix-A-Floor Repair Adhesive is strong and flexible, featuring elastomeric bonding properties that prevent future issues caused by foundation movement, expansion and contraction of the subfloor or poor original installation. Used by flooring professionals for years, this product allows any homeowner to fix loose, hollow or squeaky tiles quickly and permanently. It is non-toxic, non-flammable and eco-friendly. Whether you are repairing a small area or a large floor section, Fix-A-Floor delivers lasting results and is guaranteed for the life of your floor. Just Drill & Fill! FAQs Q: Will Fix-A-Floor work with heated floors?A: Yes. Many customers use Fix-A-Floor over heated floor elements with no issues. Turn off the heating before, during and for 48 hours after applying. Q: Some of my grout is missing. Can I still use Fix-A-Floor?A: Yes. If small gaps or cracks exist, simply Drill & Fill. The adhesive will re-bond and stabilise loose areas. If the grout is completely missing, re-grout lightly, allow it to dry and then apply Fix-A-Floor. Q: Can I repair my whole floor or just one tile?A: Fix-A-Floor works on all sizes of problem areas, from a single tile to an entire room. It is suitable for all types of tile, marble and stone floors. Q: Can I use Fix-A-Floor outside?A: Yes. It performs well in both interior and exterior applications, including patios and decks. Q: Can I use Fix-A-Floor in showers or pools?A: No. It is not recommended for areas exposed to constant or excessive moisture. Q: Is Fix-A-Floor safe?A: Yes. It is a non-toxic, non-flammable, water-based adhesive that is safe and environmentally friendly. Q: Can I use it to re-glue a tile that has come loose?A: Yes. Apply Fix-A-Floor directly to the floor where the tile was, press the tile firmly into place, apply weight and allow to cure for 24 hours. Q: Do I need to place weight on the floor after filling?A: It is recommended to place some weight, such as a heavy object or bucket, on the area to aid curing and ensure even distribution. It is not mandatory but helps achieve optimal results. Q: What if adhesive does not appear from other holes?A: The adhesive may still be spreading beneath the tile. Move to the next hole and continue filling. Make sure you are not pressing the nozzle down onto the subfloor during application.
$34.95
Note: This product is formulated for timber floors. If you need an adhesive for tiled floors, please use the regular Fix-A-Floor available Click here. NEW – Fix-A-Floor Polyurethane Wood Floor Repair Adhesive features an extra-strength, super-blend formula specifically designed for re-bonding loose, hollow, squeaky, popping, or bouncy timber floors. There’s no need to remove or replace floorboards — simply Drill & Fill for a long-lasting, nearly invisible repair. The precision nozzle allows for very small drill holes, ensuring a clean finish. Ideal for all solid hardwood, engineered timber, and bamboo floors. Suitable for both indoor and outdoor use, and for small or large repair areas. Odourless and very low in VOCs. Coverage: One 300 mL tube covers approximately 0.37 m² (around 600 mm x 600 mm). Just Drill & Fill! Flooring professionals often prefer polyurethane when repairing timber floors due to its strength and flexibility. The Fix-A-Floor polyurethane formula does not foam or expand when applied and cures within 24 hours. Once set, it moves naturally with the timber’s expansion and contraction, preventing cracking or bond failure. Perfect for permanently fixing loose, squeaky, or bouncy floors. Not recommended for use in moist or wet areas. The Fix-A-Floor Large Application Syringe is another excellent option for applying the adhesive if you’d like to drill even smaller holes than 3.5 mm. Always test on a small area first to confirm desired results, and keep from freezing before use. Directions for Repairing Timber Floors: Locate problem areas by tapping the floor with a wooden dowel, broom handle, or similar object, and mark the perimeter using chalk or painter’s tape. Inside the marked area, use a 3.5 mm drill bit and drill at least one hole on each end of the affected floorboard(s). Larger areas may require additional holes. Vacuum debris from each hole. Remove the cap and unscrew the nozzle. Pierce a large hole in the tube with an awl or similar tool. If needed, clear the nozzle before screwing it back on. Using a quality caulking gun, inject Fix-A-Floor into each drilled hole. When adhesive seeps from adjacent holes, you have achieved full coverage. Place a finger over the nozzle when moving between holes to prevent spills. Once complete, wipe away any excess with a damp cloth or sponge and allow to cure for 24 hours before filling holes. Use a matching timber filler or putty from your local hardware store. Clean any residue with mineral turpentine. Your floor is FIXED!
$49.95
Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$23.00
Say Goodbye to Stubborn, Sticky Messes! Tired of wrestling with stubborn price tags that tear and leave a papery, sticky mess? Frustrated by gummy residue left behind by tape on new appliances or furniture? We've all been there, risking our fingernails and damaging surfaces trying to scrape and scrub away unwanted adhesives. It’s time to stop the struggle. Introducing Un-Du® Adhesive Remover, the ultimate solution from Glues Australia that works like magic. This isn't just another solvent; it's a revolutionary removal system. Unlike harsh chemicals that dissolve glue and ruin your items, the Un-Du® formula cleverly works by temporarily neutralizing the adhesive. A few drops are all it takes to seep under the label or sticker, breaking the bond with the surface. Simply lift it off cleanly and effortlessly with the handy included scraper tool. The best part? Once the fast-evaporating Un-Du® formula disappears, the stickiness on the sticker returns, allowing you to reuse it somewhere else! It’s the perfect tool for repositioning labels, photos, and more. An Essential Tool for Every Australian Home From the kitchen to the garage, you'll find hundreds of uses for Un-Du®. It’s the one tool that’s more versatile than duct tape, designed to solve all those sticky problems that pop up in daily life. Keep a bottle handy and you'll always be prepared. Gift Giving Made Easy: Effortlessly removes price stickers from delicate gifts like crystal vases, books, and photo frames without leaving a trace. Clean Up Your Car: Finally get rid of that old bumper sticker from your ute or the remnants of a parking permit on your windscreen without damaging the paint or glass. Appliance & Furniture Rescue: Safely removes warranty stickers, energy rating labels, and masking tape from new fridges, TVs, and fine wood furniture. Household Accidents: Lifts chewing gum from carpet, tar from floors, and crayon marks from walls with remarkable ease. The Ultimate Office & Warehouse Productivity Hack Streamline your workflow and maintain a clean, professional workspace. Un-Du® is an indispensable asset for any office, mailroom, or warehouse environment, saving you time, money, and frustration. Package & Mail Management: Open self-sealing envelopes and padded mailers without tearing them, perfect for retrieving contents or reusing packaging. File & Asset Organisation: Easily remove and replace labels on files, shelves, computer disks, and office equipment without leaving a sticky, dirt-collecting residue. Mistake Correction: Quickly lifts correction fluid (White Out) from documents without smudging or tearing the paper. Workspace Maintenance: Removes old tape marks from desks, partitions, and windows, keeping your office looking pristine. A Must-Have for Crafters and Memory Keepers Your precious memories and delicate projects deserve the best care. The Un-Du® formula is completely acid-free and photo-safe, making it the trusted choice for hobbyists, scrapbookers, and archivists who demand perfection and preservation. Scrapbooking Perfection: Safely lift and reposition photos in albums and scrapbooks without causing fading, yellowing, or damage. Model Making: Remove masking tape from delicate models without lifting paint or leaving residue. Paper Crafts: Adjust stickers and embellishments on acid-free and lignin-free papers with total confidence. Stop struggling and start un-sticking the clean, simple, and safe way. Add Un-Du® Adhesive & Sticker Remover to your cart today and discover a world free from sticky situations! Product Specifications Brand: Un-Du® Product Name: Adhesive & Sticker Remover Formula: Acid-Free, Photo-Safe, Quick-Evaporating Solvent Key Feature: Temporarily neutralizes adhesives, allowing for the reuse of most stickers and labels after evaporation. Residue: Leaves no oily, greasy, or sticky residue behind. Tool: Comes with an attached, non-scratching, integrated scraper tool for easy lifting. Common Applications: Sticker & Label Removal Tape & Decal Removal Price Tag Removal Gum & Tar Cleaning Correction Fluid (White Out) Lifting Opening Sealed Envelopes Safe For Use On Surfaces Including: Glass & Plastics Fine Wood Furniture Metals Carpets & Upholstery Delicate Fabrics Photos Acid & Lignin-Free Papers Painted Surfaces & Wallpaper And much more!
$19.00
The unique rubber-infused gel formula allows powerful bonds that are extremely precise even on flexible materials. Ideal for porous and vertical surfaces, and strong enough to withstand extreme conditions. The gel’s high strength non-drip formula then dries transparent to form invisible bonds that give a long lasting durability that is both weather and shock-resistant. For intricate, hard to reach spots, Loctite Power Flex Gel Control features an easy grip squeeze bottle and nozzle for precise applications. Recommended on: Rubber, Leather, Wood, Metal, Porcelain, Paper, Plastic. Properties: -Rubber infused gel formula for extra strong and flexible bonds -Ideal for porous and vertical surfaces -Water resistant -Bonds in seconds -Withstands heavy loads -Dries transparent -Easy to open, self-piercing and anti-clog cap -Choice of applicators: convenient tube or easy grip control with a longer nozzle -Suitable for use on most surfaces* -Solvent-free -* Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Step by Step Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$12.50 $10.95
For very narrow or no grout line applications - Syringe is not pre-filled.
$18.00
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be resoftened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$9.00
Why Choose Selleys Super Glue Adjustable Gel? Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes. Key Benefits: Adjustable Setting Time: Allows precise alignment before setting. Rapid Bonding: Bonds in 30 seconds for fast repairs. Versatile: Adheres to ceramics, china, metal, wood, and most plastics. Easy to Use: No mixing required, with a convenient gel formulation for clean application. Where Can This Product Be Used? Everyday household repairs on: Ceramic and China Metal and Wood Most Plastics* What Materials Is It Suitable For? Bonds a variety of porous and non-porous surfaces. Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers. How to Use Selleys Super Glue Adjustable Gel Prepare: Pierce the seal by attaching the nozzle with the cap and turning clockwise. Ensure surfaces are clean, dry, and free from dust, dirt, and grease. Apply: Apply a small amount of adhesive to the surfaces to be bonded. Press surfaces together gently and hold for several minutes to ensure sufficient bond strength. After Use: Wipe the nozzle clean with a cloth or paper. Replace the cap securely. Limitations Not suitable for use on leather, polyethylene, polypropylene, or PTFE. Will not permanently bond vessels exposed to water or dishwashers. Handy Tips for Best Results Ideal for vertical applications and slightly porous materials. Use 1 drop per cm² for optimal bonding. Sets in 30 seconds, achieving maximum bond strength in 24 hours. Clean-Up Instructions Wipe the tip of the tube with a cloth or paper after use. Replace the cap tightly to avoid drying out the product. Product Details Size: 3g Tube Colour: Clear Technology: Cyanoacrylate Recommended Use: Interior Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
$4.00
Easy to use, fast setting adhesive system to repair ALL plastics. Features -Bonds ALL Plastics, including Polyethylene (PE) and Polypropylene (PP) -Easy to Apply -Dries clear for clean, neat results -Fast Bond: 2-30 seconds -No clamping necessary -No mixing required -self-piercing, clog-free cap on adhesive -Also bonds plastic to other surfaces: Metal, timber, china, rubber, leather Where can this product be used? -For interior projects and repairs -For fast & easy repair of household items made from plastic -Repair Toys & Games -Fix Car accessories -Repair Kitchen plastics and utensils -Repair Office items -Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet -Best results for Nylon items (e.g. car parts) are achieved without initial priming. Contact Selleys consumer advice if unsure of plastic type. -Not suitable for use on glass – we recommend Selleys Araldite Ultra Clear. What materials is this product suitable for? -ALL Plastics -Adhering Plastic to Metals China Rubber Leather How to use this product -Ensure the surfaces to be joined are close fitting, clean, dry and free of dust. -Using the primer pen, liberally coat plastic surface/s that are to be bonded. -Pierce seal at end of the adhesive tube by attaching nozzle and cap and turning clockwise. -Remove cap and apply a very small amount of glue to one surface only. Bring surfaces together and apply slight pressure. -The adhesive will grab within 2-30 seconds, depending on environmental conditions and materials being bonded. -Allow at least 30 minutes for sufficient bond strength for practical use. -Wipe tip of the tube, replace the cap and store upright in a dry cool place. Handy tips -If using on leather test on an inconspicuous area first as adhesive may cause leather to discolour or harden. -Not suitable to repair items that will contain hot liquids. -Best results for nylon items are achieved without Initial priming (e.g car parts). Contact Selleys Consumer Advice if unsure of plastic type. -Will also bond plastic to non-plastic surfaces (Metals, Timber, China, Rubber, Leather). Do not use primer on non-plastic surfaces. -After use, wipe excess product from the adhesive nozzle with a tissue dipped in nail polish remover. -For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. -In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in the hot soapy water. -Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use. Safety tips -Keep Out of reach of Children -Avoid contact with skin and eyes and avoid breathing in the vapour. -Bonds on contact. Should fingers stick together apply a solvent such as acetone (nail polish remover) to contact areas then wash with water. -Do not use solvents near eyes or open wounds. -Highly Flammable, keep away from sources of ignition. -Contents of the pen may cause lung damage if swallowed. -This product is hazardous according to the criteria of NOHSC and HSNO. For frequent hobby or occupational use, please refer to the Material Safety Data Sheet. -For Advice, contact a Poisons Information Centre (phone Aust. 131 126, NZ 0800 764 766) or a doctor. -In case of eye contact immediately flush with water for at least 15 minutes and seek medical attention. Storage and re-use -Ensure caps are replaced and store in a cool dry place.
$8.51
Clear Boyle Craft Glue Boyle Craft Glue (Clear) is a versatile, water-based adhesive designed for everyday making and detailed craft work. It dries clear and odourless, making it perfect for neat, mess-free results on paper projects, school assignments, scrapbooking, model making, décor builds and more. Why You’ll Love It Dries crystal clear for a clean, professional finish. Water-based & odourless for a low-fuss, indoor craft experience. Heat & light resistant—ideal for display pieces exposed to room lighting/sunlit interiors. Easy-squeeze bottle gives smooth, controlled bead lines and spot application. Cleans up with water—simply wipe while wet for quick tidy-ups. Suitable Materials Formulated for strong, reliable bonds on: Paper, cardboard & posters Wood, balsa & craft sticks Plastics* Glass & ceramics Metal embellishments Fabrics & felt Yarns, beads & sequins Leather and more *Always test first—some low-energy plastics may require light surface prep. Great For School projects & classroom crafts Cardmaking, scrapbooks & photo boards DIY décor, event styling & mood boards Miniatures, models & hobby builds Textile embellishment on felt and fabric (non-washwear items) How to Use Prep: Ensure surfaces are clean, dry and free of dust or oils. Lightly roughen very smooth surfaces for best grab. Apply: Squeeze a thin, even layer to one surface. For porous materials (paper, cardboard, wood), a little goes a long way. Assemble: Press parts together. Use light pressure, clips or tape if needed to hold while setting. Dry: Allow to dry thoroughly. Dry time varies with bead thickness, temperature and humidity. Clean-up: Wipe excess immediately with a damp cloth. Wash tools in water while glue is still wet. Good to Know Indoor use: Formulated for indoor crafting and display. Clear finish: Dries transparent to help hide glue lines and squeeze-out. Heat & light resistance: Helps projects maintain appearance under typical indoor conditions. Washes out with water: Clean hands, tools and fresh spills while wet. Specifications Base Water-based Appearance (dry) Clear Odour Odourless Cleanup Water (while wet) Use Indoor Tips & Testing For non-porous surfaces (glass, metal, some plastics), apply a thin coat to each surface, wait briefly, then join for better grab. Always perform a small test on off-cuts or an inconspicuous area to confirm compatibility and finish. Avoid heavy, load-bearing or structural applications—this is a craft-grade adhesive. FAQs Does it dry clear?Yes—Boyle Craft Glue dries clear for a neat finish. Can I wash it out?Yes—while wet, it washes out with water. Once fully dry/cured, removal may be more difficult. Is it suitable outdoors?It’s designed for indoor craft projects. For outdoor or constantly wet environments, choose a weather-rated adhesive.
$14.89
![Fix-A-Floor Loose Tile Repair Adhesive Needle [Pro Pack] Includes a Micro Syringe Injector and Drill Bit](http://gluesaustralia.com.au/cdn/shop/files/One_33b7ac3c-91f8-445e-9f7a-f35eb32fd49e.jpg?v=1760493150&width=645)
![Fix-A-Floor Loose Tile Repair Adhesive Needle [Pro Pack] Includes a Micro Syringe Injector and Drill Bit](http://gluesaustralia.com.au/cdn/shop/files/513iY1tnifL._SL1013_2cc193b4-9c50-4e36-a6e8-69a36d42769f.jpg?v=1760493150&width=645)
Note: If you are working on a timber floor, you will need to use Fix-A-Floor Polyurethane for Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive, now patented, is an extra-strength bonding adhesive designed specifically for re-bonding loose and hollow tiles, marble and stone without the cost and mess of removing or replacing them. Fix-A-Floor is a simple DIY repair solution that is fast, easy and affordable, and surprisingly rewarding. If you can operate a drill, a caulking gun and mix a small batch of grout, you can do it. It works on all types of subfloor materials. Just Drill & Fill! Tip: For more precise application or smaller holes, you can include the 30 mL Adhesive Syringe with Blunt Tip Fill Needle when purchasing this product. It makes applying the adhesive cleaner and more accurate, especially in tight or narrow grout lines. The Nozzle The nozzle of the 300 mL Fix-A-Floor tube is specially engineered with a pre-drilled 3 mm hole to make it ideal for filling drilled holes in loose or hollow tile, marble and stone floors. It is firm enough to form a strong seal for optimal flow and complete coverage. Markings on the nozzle indicate cut points for 4.5 mm, 6 mm or any size you need, making it suitable for both narrow grout lines and wider applications. The Adhesive Fix-A-Floor Repair Adhesive is strong and flexible, featuring elastomeric bonding properties that prevent future issues caused by foundation movement, expansion and contraction of the subfloor or poor original installation. Used by flooring professionals for years, this product allows any homeowner to fix loose, hollow or squeaky tiles quickly and permanently. It is non-toxic, non-flammable and eco-friendly. Whether you are repairing a small area or a large floor section, Fix-A-Floor delivers lasting results and is guaranteed for the life of your floor. Just Drill & Fill! FAQs Q: Will Fix-A-Floor work with heated floors?A: Yes. Many customers use Fix-A-Floor over heated floor elements with no issues. Turn off the heating before, during and for 48 hours after applying. Q: Some of my grout is missing. Can I still use Fix-A-Floor?A: Yes. If small gaps or cracks exist, simply Drill & Fill. The adhesive will re-bond and stabilise loose areas. If the grout is completely missing, re-grout lightly, allow it to dry and then apply Fix-A-Floor. Q: Can I repair my whole floor or just one tile?A: Fix-A-Floor works on all sizes of problem areas, from a single tile to an entire room. It is suitable for all types of tile, marble and stone floors. Q: Can I use Fix-A-Floor outside?A: Yes. It performs well in both interior and exterior applications, including patios and decks. Q: Can I use Fix-A-Floor in showers or pools?A: No. It is not recommended for areas exposed to constant or excessive moisture. Q: Is Fix-A-Floor safe?A: Yes. It is a non-toxic, non-flammable, water-based adhesive that is safe and environmentally friendly. Q: Can I use it to re-glue a tile that has come loose?A: Yes. Apply Fix-A-Floor directly to the floor where the tile was, press the tile firmly into place, apply weight and allow to cure for 24 hours. Q: Do I need to place weight on the floor after filling?A: It is recommended to place some weight, such as a heavy object or bucket, on the area to aid curing and ensure even distribution. It is not mandatory but helps achieve optimal results. Q: What if adhesive does not appear from other holes?A: The adhesive may still be spreading beneath the tile. Move to the next hole and continue filling. Make sure you are not pressing the nozzle down onto the subfloor during application.
$39.95
Repair flexible plastic items easily with Bostik Soft Plastics Glue. This clear, quick-drying adhesive creates a strong yet flexible bond that withstands stretching, bending and movement, making it perfect for repairing soft plastic and vinyl materials around the home, outdoors or on the go. Ideal for Inflatable toys, air mattresses and pool liners Vinyl upholstery, raincoats and tarps Plastic footwear, shower curtains and coated fabrics Features and Benefits Dries clear for neat, invisible repairs Flexible and waterproof once cured Strong, long-lasting bond for soft PVC and vinyl Easy to apply directly from the tube Directions Ensure surfaces are clean, dry and free from grease or dust. Apply a thin, even layer of glue to both surfaces. Press together firmly and allow to dry for 10–15 minutes. For best results, leave for 24 hours to achieve full bond strength. Clean Up Wipe away excess adhesive with a clean cloth before it sets. Once cured, mechanical removal may be required. Safety Information Use in a well-ventilated area. Avoid contact with skin and eyes. Keep out of reach of children.
$12.98
Tarzan’s Grip new formulation is a clear, flexible, general purpose solvent-based adhesive for household and hobby uses. An all-purpose glue which bonds almost everything Grabs in minutes - the exact "grab time" depends on the surfaces to be joined Fast drying Water resistant
$4.89
SikaBond®-145 SuperGrip Premium polyurethane construction adhesive with fast build up of Strength SikaBond®-145 SuperGrip is a premium grade one-component polyurethane construction adhesive with good initial grab and high strength after 30 minutes^. SikaBond®-145 SuperGrip is a versatile, ready to use, fast curing, general purpose construction adhesive suitable for interior and exterior use. One-component. Interior & exterior. Non-shrink. Usage SikaBond®-145 SuperGrip is suitable for use in construction and repair applications where a permanent strong bond is required between porous-nonporous surfaces. SikaBond®-145 SuperGrip is suitable for bonding most common construction materials such as: Wood MDF Concrete Brick Metal Polystrene Polyurethane foam Some PVC Marble Granite Ceramic LOSP Timber Advantages One-component. Interior & exterior. Non-shrink. Non-sag. High initial grab. Adheres rapidly. Stong bond in 30 minutes^. Fast cure. Solvent-free. Resistant to heat. Resistant to weathering. Water resistant -D4 according to DIN En 204 Applies white, can dry translucent if applied in thin layers.
$24.15
SikaBond®-115 Max Tack is a 1-part construction adhesive with high final strength, designed for bonding most construction material substrates. It is suitable for internal and sheltered outdoor use. Key Features: Easy to apply Easy to clean Rapid build-up of strength High final strength Very low emissions (Acrylic dispersion) Applications: Ideal for bonding various construction components, including: Skirting boards Wooden frames Battens Mouldings Panels Terracotta tiles Anodised aluminium Polystyrene mouldings and ceiling tiles Bonds well to materials like: Concrete Mortar Fibre cement Wood Painted surfaces Shelf Life & Storage: Shelf life: 18 months from production date. Storage conditions: Store in original, unopened, undamaged packaging in a dry environment, at temperatures between +5°C and +25°C. Technical Details: Density: ~1.40 kg/l (ISO 1183-1) Application Instructions: Follow standard building and construction practices when applying SikaBond®-115 Max Tack. Substrate Preparation: Ensure the substrate is clean, sound, dry, and free from contaminants like oil, grease, cement laitance, old sealants, and loose paint. Remove dust and friable material through wire brushing, grinding, sanding, or other mechanical methods. For best results, follow these priming and pre-treatment steps: Non-Porous Substrates: For surfaces such as aluminium, anodised aluminium, stainless steel, PVC, and glazed tiles: Slightly roughen the surface using a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Wait 15 minutes before applying adhesive (within 6 hours). For metals like copper, brass, and titanium-zinc: Clean and pre-treat using Sika® Aktivator-205. After 15 minutes, apply Sika® Primer-3 N by brush. Wait at least 30 minutes (within 8 hours) before applying adhesive. Porous Substrates: For concrete, aerated concrete, mortars, and bricks: Prime the surface with Sika® Primer-3 N. Wait at least 30 minutes (within 8 hours) before applying adhesive. Note: Primers are adhesion promoters and are not a substitute for proper surface preparation. They also enhance the long-term bond strength. Cleaning of Tools: Clean tools and equipment immediately after use with Sika® Remover-208. For skin cleaning, use Sika® Cleaning Wipes-100. Once cured, the adhesive can only be removed mechanically. For more information, please consult Sika Technical Services.
$17.40
![Selleys No More Gaps Multipurpose Sealant Filler 150g [White]](http://gluesaustralia.com.au/cdn/shop/files/87cc1e989ee946138f896f38cf05e9d4.jpg?v=1757753073&width=645)
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 300% elongation/stretch and up to +/- 15% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage. Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application). Is formulated for long term resistance to cracking and crumbling. Easy water clean-up Will not stain building materials. Has good resistance to weathering. Low toxic, low odour, low VOC, less harmful to the environment Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles which are not exposed to water In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Paint Many other building materials
$8.00
SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to respond to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces How to use this product Ensure the surfaces to be bonded are clean, dry and free from dust, grease, oil and loose powdery materials. If porous surfaces are greasy or dirty, we would recommend cleaning the surface with SELLEYS LIQUID SUGAR SOAP, and allow to dry. If the surface is non-porous eg glass or metal, firstly clean the surface with Mineral Turpetine and then again with Methylated Spirits, and allow to dry. If there is old difficult to remove residue such as old flaky paint, we recommend using paint stripper such as SELLEYS KWIK STRIP SMART, and allow to dry. On wet timber pooled water should be wiped off. Highly oily timber types may need to be wiped with solvent prior to application to remove surface oils. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/ Course grain, as the construction adhesive will adhere more readily to a scratched up surface. Cut the seal at the top of the cartridge. Cut the nozzle end to desired opening (approx. 5mm diameter). Fit to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of work which requires a caulking gun. Apply a bead of product along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. Fix the surfaces with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. The product is repositionable for up to 20 minutes after fitting. Allow the adhesive to set (at least 24 hours) before removing any temporary fasteners or clamping. For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-5 minutes before firmly joining. The time it takes to form a strong bond depends on the nature and conditions of the application. In most situations strong bonds can be achieved after 24 hours and will continue to strengthen over a 2-3 day period. The product will fully cure up to 7 days. When the product is still wet it can be removed with mineral turpetine, otherwise if the product is dry it can be removed by sanding or scraping, we recommend using a 50mm ROTA COTA Soft Grip Scraper. Clean any excess from your hands with SELLEYS Hand Kleen Wipes. To eliminate squeaks in tongue and groove flooring, apply a bead of Liquid nails into the groove or each board when installing. Handy tips When applying to one surface, ensure sufficient LIQUID NAILS Original is used so that some adhesive extrudes out when surfaces are brought together then wipe off excess if necessary. If glue is not visible, then insufficient contact may not have been made between the surfaces and a weak joint may result. LIQUID NAILS Original should always be used in conjunction with mechanical fasteners in structural, critical or high stress applications. LIQUID NAILS Original is sometimes called LIQUID NAILS (SOLVENT) to differentiate it from the other Liquid Nails products. LIQUID NAILS Original shrinks slightly on curing. Cured LIQUID NAILS Original residues can be removed by holding a rag soaked in Mineral Turps against the residue, then rubbing the residue once softened. Mineral Turps penetrates in this way at approximately 1 mm per hour. When Liquid Nails Original joints are directly exposed to the weather, it is recommended to seal around the edges with a silicone sealant to prevent water ponding inside the joint and thus weaken the joint. LIQUID NAILS Original is NOT recommended for use on mirrors or polystyrene. Use LIQUID NAILS MIRROR METAL GLASS for mirrors and LIQUID NAILS FAST for polystyrene. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job.
$5.00
Liquid Nails Fast is a water-based high strength (*) construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. After drying it is beige (light tan) in colour. UsesLiquid Nails Fast has high initial (immediate) grab which reduces the need to support joins while the adhesive cures. The initial grab works best with porous surfaces. It will bond to many building materials including MDF, particle board, timber, plaster board, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results are achieved when at least one surface is porous. Liquid Nails Fast would typically be used for the following applications: Areas where nailing is not desirableSkirting boards, architraves, cornicesWall panelling to masonryStyrene foam to metal roofing Technical FeaturesFast grab – high initial holding minimises slippage when adhering on vertical surfacesMeets or exceeds AS 2329-1999 (Mastic adhesives for fixing wall boards)Does not drip, sag or string between panelsBridges gaps and will adhere materials with uneven surfacesLow mess – excess and squeeze out is easily cleaned up with wet clothNo solvent fumes – ideal for large indoor jobsHigh flexibility – will withstand thermal movement and vibrationHigh heat resistance – will not lose bonds exposed to sunPaintable when dryEasy to extrude at all temperatures Application TipsLiquid Nails Fast should always be used in conjunction with permanent mechanical fasteners except in low stress applications such as wall panelling and fixing light weight objects. (Bonds may creep under constant heavy loads.)Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications.In cold or damp weather and between non-porous materials drying time is greatly extendedThick applications take longer to dry than thin applicationsPre-test plastics to determine suitable bonding. Adheres well to UPVC. Not suitable for polyethylene and polypropylene. For wood flooring applications Liquid Nails (solvent based) is recommended. [Liquid Nails Fast is satisfactory for fixing sheet flooring (particleboard/ply) to joists in conjunction with the manufacturer’s minimum nailing specification but is not recommended for fixing sheet wood flooring to flat surfaces such as existing or concrete floors. Technical Details and PerformanceFor porous substrates good bond strength is achieved after 24 hours and will continue to strengthen over 2-3 day period. Time for strong bond depends on nature and conditions of application. In cold or damp weather and between non-porous materials, drying time is greatly extended. Indicative information only, not to be used for setting specifications. AppearanceLump free, air-free smooth beige paste Specific GravityApprox. 1.44g/mL @ 25oC ViscosityTypical 7000 – 9000 Poise SlumpTypical: 0mm Shear Adhesion Strength (7 days) (AS2329)Greater than 1500kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure)Typical 40N/25mm (wire gauze off hoop pine.(Variant to AS2329)) Initial Bond Strength AS2329-1999D (Tested after 24 hrs)Over 200kPa Heat ResistanceBonds will resist temporary exposure to temperatures up to 140oC. Constant high temperatures will reduce constant load holding power (see below). Creep resistance (under constant load)*2Fully cured *1 bonds of 625 sq. mm will hold up to 500g loads (7.8kPa) in shear at constant 80oC Fully cured *1 bonds of 625 sq.mm will hold up to 100kPa in shear at 25oC (equivalent to 6Kg load on 625 sq.mm bond area) Coverage15 metres of a 5mm diameter bead 1mm thick bonds on porous substrates cured at least 7 days at temps above 25oCThis data is provided as indicative only. Not to be used for design purposes. Thick bonds reduce constant load holding power and increase curing time. Larger bond areas increase curing time. CleaningLiquid Nails Fast may be cleaned off with hot soapy water or a damp cloth while still wet. Dry adhesive is best removed by scraping or peeling.
$7.00
Crystal clear Can be used even on damp/wet and impervious surfaces. Closest you will get to a transparent Ritetack 290ml tube Used indoors and outdoors as long as not exposed to UV. Clear adhesive Invisifix is a versatile 290ml tube of clear construction adhesive that lets you see exactly what you’re gluing. A quick, easy-to-use, water-friendly clear construction adhesive allows you to see exactly what you’re gluing. Reasons why to use Invisifix The excess clear construction adhesive always finds a way to make itself noticeable. Sometimes it is even difficult to remove it. With Invisifix, you don’t have to worry about unaesthetic colours since it is literally see-through! Amazing fast grab! That means no time wasted holding things into place while you wait for them to adhere. With Invisifix, you apply it to the surface, and it immediately sticks! Invisifix is water-friendly, so no more breaking a sweat while trying to dry surfaces before applying. This comes in handy if you’re thinking of applying Invisifix Clear Adhesive in areas prone to humidity and dampness, like bathrooms, pool areas, or kitchens. This adhesive can stretch up to 375% from its original size, and that’s important if you want some flexibility in your adhesion. That means that sudden movements like some impact won’t compromise the integrity of your adhesive and of whatever it is holding. Not only does Invisifix work on virtually any surface, but it also won’t stain any of them, including the porous ones, like a stone!
$9.95
Fast setting supa glue in a convenient bottle that allows easy, controlled and precise application. Features Easy, controlled application Non-drip glue saver nozzle, reduces waste and mess. Long fine nozzle for precise application Bonds a variety of surfaces Extremely fast setting Dries Clear for clean, neat results Water resistant No clamping necessary No mixing required Maximum strength achieved in 12 hours Only takes 45 seconds to achieve initial bond Non-clog cap Forms a rigid bond Upright self-standing bottle Comfortable to hold Where can this product be used? Ideal for small repair jobs or when immediate results are required. Water resistant not water proof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene. Leather may become hardened or discoloured For interior use only Not suitable for repairing items that are in direct contact with hot liquids Will not permanently bond glass or materials containing alkaline elements. Has no gap filling properties therefore surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Bonds a variety of porous and non-porous surfaces Metals China Rubber Leather Some plastics Wood How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Hold bottle in an upright position. Pierce seal by attaching nozzle and cap and turning clockwise. Remove cap and squeeze gently to apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. (30 seconds). The product grabs within 5-30 seconds, depending on environmental conditions and substrates to be bonded. Allow 30 minutes for sufficient bond strength for practical use. Maximum bond strength reached after 12 hours. Handy tips Cyanoacrylate adhesives can create a white residue on the surface of a substrate if the area is not well ventilated. Clean the affected area with acetone to remove residue. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. Excellent when used with other adhesives, as the temporary tack For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. Acetone (nail polish remover) or Olive oil can also be used to remove Quick Fix from skin. While superglue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Super glues cure more slowly when large amounts are used. For faster cure use sparingly. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Reseal cap in a clockwise direction. Tap bottle lightly on a flat surface to clear excess product from nozzle. To remove excess from substrates, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using thias method. Ensure cap is replaced and store in a cool dry place. Cyanoacrylate based adhesives polymerise in the presence of moisture. Store Upright. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$6.00
Single Shot, no mess just throw away Self piercing tube Bonds in 10 seconds Where can this product be used? Ideal for small repair jobs or when immediate results are required For interior projects and repairs Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or materials containing alkaline elements Has no gap filling properties, therefore, surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Metals China Rubber Leather Some plastics
$6.00
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$22.98
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$19.67
The Loctite Super Glue Creative Pen offers the ultimate solution for precise, fast, and reliable bonding. Its ergonomic pen design ensures a controlled application, perfect for intricate tasks like crafting, DIY projects, or quick household repairs. The pen tip provides pinpoint accuracy, so you can apply just the right amount of glue, reducing mess and waste. Loctite’s fast-drying formula creates a strong bond on materials such as wood, plastic, metal, ceramic, and leather, making it versatile for any project. Whether you're fixing a broken ornament, assembling models, or working on craft projects with the kids, Loctite Super Glue Creative Pen guarantees a professional finish every time. LOCTITE® Super Glue Creative Pen Precision bonding on wood, metal, plastic, rubber, and more. Waterproof, weather-resistant, and shock-resistant. Equipped with a long nozzle and easy-grip squeeze bottle for fast and accurate application. Characteristics: LOCTITE® Super Glue Creative Pen is a one-part instant gel adhesive in a convenient dispenser, perfect for home use. It forms strong bonds between a wide range of common materials, including plastics, rubbers, metals, wood, ceramics, leather, fabrics, cardboard, and paper. Its non-drip formula allows for use on vertical or overhead surfaces. The ergonomic pack design ensures precise application, ideal for bonding smaller items. Bonding Speed: Initial adhesion in 5 to 30 seconds, depending on the substrate. Bond Strength (ISO 4587): 10 to 20 N/mm² (tensile shear) in 12 to 24 hours, depending on the substrate. Water-resistant to EN204-D3 standard. Ceramic bonds can withstand over 50 dishwasher cycles under controlled laboratory conditions. Instructions for Use: Ensure all surfaces to be bonded are clean, dry, and fit closely. Twist the cap clockwise onto the pack until you hear a clicking sound. Do not overtighten; a three-quarter turn is sufficient. Avoid skin contact with the glue. Gently squeeze the rubber panels and apply a minimal amount of adhesive to one surface. Press parts together immediately and hold with hand pressure for at least 1 minute. Allow the bond to set undisturbed for 10 minutes, or preferably overnight, to achieve full bond strength. Protect work surfaces and avoid spills. Remove cured glue with LOCTITE® Glue Remover. For best results, apply at room temperature (15-30°C) with at least 30% relative humidity. After use, wipe the nozzle clean with a tissue, replace the cap, and store in a cool, dry place. Technical Data: Composition: Ethyl cyanoacrylate Appearance: Clear gel Density: 1.1 g/cm³ @ 20°C Viscosity: Gel Safety: Refer to SDS 2669372 Shelf Life: 30 months unopened (stored at 2-8°C) Limitations: Do not use on dusty, dirty, or wet surfaces. Not suitable for bonding polypropylene, polyethylene, PTFE, silicone rubber, glass, glazed surfaces, very soft leather, or foams. Do not use for bonding items exposed to hot liquids or high temperatures for extended periods. Optimum performance is achieved in dry conditions. Storage: Store in a cool, dry place, out of reach of children. Why choose Glues Australia? We provide premium-quality adhesives like Loctite, backed by our exceptional customer service. With fast, reliable delivery across Australia, you’ll get the products you need when you need them. Shop confidently with Glues Australia, your trusted adhesive supplier!
$11.57
A rapid dual-action adhesive system is specially designed to work on plastic to form resilient, invisible bonds in seconds. Recommended on: Plastic, Porcelain, Metal, Rubber, Leather, Wood, Paper. Properties: Bonds even difficult to bond plastics such as polyethylene (PE) and polypropylene (PP) Bonds in seconds Dries transparent Easy to open, self-piercing and anti-clog cap Suitable for use on most surfaces* Solvent-free * Except Styropor®, car glass and synthetic fibres. Use: Ensure surfaces to be joined are clean, completely dry and close fitting. Using the Surface Activator like a pen apply it to both surfaces and wait 60 seconds to dry. Twist the glue cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$10.67
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.90
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance: Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product: General Use -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$8.00
Selleys Auto Fix Auto Sealant Translucent 100 mL Keep water out and vibrations at bay with a clear automotive sealant that bonds fast and stays flexible. Selleys Auto Fix Auto Sealant is a 100 percent neutral cure silicone designed for cars, caravans, and general automotive sealing where a durable waterproof finish is essential. Why you will like it 100 percent neutral cure silicone Versatile general purpose sealant for automotive use Waterproof seal that resists vibration and temperature extremes UV and weather resistant for long lasting performance Skins in 5 minutes, set to touch in 30 minutes, full cure in 24 hours Where to use it Adheres to most auto and caravan materials, including: Glass and painted surfaces Fiberglass and most plastics Trim components Most rubbers Typical applications Sealing around lights, windows, and trim Gasket style sealing where a flexible waterproof joint is required General leak prevention and small gap sealing in automotive and caravan fittings Directions Preparation: Clean surfaces so they are free of dust, oil, and moisture. Wipe with mineral turpentine and allow to dry. Cut and load: Remove cap, unscrew nozzle, remove seal. Refit nozzle and cut at a 45 degree angle to the desired bead size. Apply: Squeeze the tube with steady pressure to lay a continuous bead. Smooth with a gloved finger before the sealant skins. Clean up: Before cure, clean tools and excess with mineral turpentine. Once cured, remove by cutting or scraping. After use: Replace cap. Let cured material in the nozzle be removed before next use. Handy tips Mask edges for neat joints. Remove tape before skin forms. Work within the skin time to achieve a smooth finish. Limitations Not recommended for Natural rubber, NBR, or Chloroprene Neoprene Technical details Technology 100 percent neutral cure silicone Colour Translucent Packaging Tube 100 mL Density 1.02 g per mL Application temperature -20°C to 50°C Skin time 5 minutes Shore A hardness 25 Elongation at break 370 percent Movement capability 25 percent Service temperature -40°C to 180°C VOC 26 g per L Clean up and storage Clean uncured sealant with mineral turpentine Store below 30°C in a cool dry place Use within 24 months from date of production Safety: Refer to the product SDS for handling and first aid information. Use in a well ventilated area and keep out of reach of children.
$21.55
Selleys Auto Fix Windscreen Sealant 100 mL - Black Stop leaks fast around windscreens and windows with a durable, weather resistant silicone seal. Selleys Auto Fix Windscreen Sealant forms a waterproof barrier that resists vibration, UV and temperature extremes, keeping water, dust and drafts out. Why choose this sealant 100 percent neutral cure silicone for reliable sealing Forms a waterproof seal to stop leaks quickly UV and weather resistant for long term performance Skins in 5 minutes and is touch dry in about 30 minutes Handles joint movement up to 25 percent Suitable surfaces Glass and windscreens Rubber surrounds and trims Painted surfaces and most plastics Metal frames and channels Typical applications Sealing between windscreen glass and rubber Sealing between rubber and metal frames Stopping minor water ingress around vehicle windows General sealing where a flexible, black silicone finish is desired Key specifications Technology Neutral cure silicone Colour Black Movement capability Up to 25 percent Skin time About 5 minutes Set time About 30 minutes Full cure Approximately 24 hours Service temperature -40°C to 180°C Application temperature -20°C to 50°C VOC 26 g/L Pack size 100 mL tube Directions Remove any dirt or moisture between the rubber and glass, or rubber and metal. Clean with mineral turpentine and allow to dry. Remove cap, unscrew nozzle, pierce inner seal, refit nozzle, then cut the tip at a 45 degree angle. Insert the nozzle between the rubber and glass or rubber and metal where possible. Squeeze the tube with steady pressure to push sealant into the joint. Smooth off with a gloved finger. If additional smoothing is needed, do it before the sealant skins. Clean up uncured sealant with mineral turpentine. Cured material must be cut or scraped away. Replace the cap after use. Allow sealant in the nozzle to cure, then remove before next use. Handy tips For neat lines, mask both sides of the joint and remove tape before the sealant skins. Best results occur when the joint is clean, dry and free of loose material. Limitations Not recommended on natural rubber, NBR or chloroprene neoprene due to poor adhesion. Clean up and storage Clean uncured sealant with mineral turpentine. Remove cured sealant by cutting or scraping. Store in a cool, dry place below 30°C. Use within 24 months of production. What you get 1 x Selleys Auto Fix Windscreen Sealant 100 mL - Black
$23.08
Shower Plug Penetrating Sealer 220mL Stop leaks without removing tiles. Shower Plug penetrates into masonry surfaces and forms a water repellent barrier that fixes and prevents leaks in showers, balconies and other masonry areas. One application lasts 10 years. Penetrates grout, tile and masonry to block water at the source No tile removal required Indoor and outdoor use, friction and UV resistant Does not change surface appearance or make it slippery Makes surfaces easier to clean and helps prevent mould Breathable seal allows trapped moisture below tiles to escape Seals gaps up to 1 mm. For wider cracks, repair with grout or silicone first Why Shower Plug Released in 1992, Shower Plug is the original Australian penetrating sealer technology for leaking shower repair. It delivers cost and time efficiency with proven longevity and reliability. Fixing a leaking shower, methods compared Item Tile and membrane removal and replacement Shower Plug 220mL Typical cost > $1000 $55 Time required > 5 days 30 minute application, ready to use in 12 hours Skill level Trade DIY Effective lifespan Average 5 years 10 years minimum Coverage Approx. 7 m² per pack (about 75 ft²), depending on porosity. Where to use Grout Tiles including ceramic, porcelain, marble, glazed or unglazed, terrazzo, slate, terracotta and more Concrete and masonry Bare plaster. If painting later, use a solvent primer undercoat after treatment Showers, balconies, other tiled or masonry wet areas Not suitable for Plastics and polymers such as polyurethane and polycarbonate Glass Metal Wood Painted surfaces How to apply Ensure the surface is clean and dry. Using a natural bristle brush, apply the first coat evenly. After 5 minutes, apply a second coat. Five minutes after the second coat, wipe away any remaining excess from the surface. Allow to cure. Area is ready to use in 12 hours. Important: Wipe the final coat off within 5 minutes. If left to dry on the surface, a white residue may appear. Remove any residue with turpentine. Good to know Gives off a mild solvent type odour during application and cure. This fades by the end of curing. Does not affect clothing under normal use. Safer to handle than household paint when used as directed. Always use protective gear and ventilation. Specifications SKU SP220ML Category Shower Plug Pack size 220 mL Coverage Up to 7 m² per pack Weight 0.25 kg Dimensions 7.5 cm x 7.5 cm x 8 cm Finish Invisible. No change to surface look or feel Use areas Showers, balconies, tiled and masonry wet areas Lifespan 10 years Directions recap Two coats applied 5 minutes apart. Wipe off excess 5 minutes after second coat. Ready to use in 12 hours. What you get Shower Plug 220 mL bottle Simple step by step instructions Shower Plug gives you the solution.
$61.69
Boston Liquid Thread Sealant 50g Boston Liquid Thread Sealant is an anaerobic sealant formulated to seal metal threads on gas and water pipes. It cures in the absence of air once confined between metal surfaces, creating a reliable, leak resistant seal. Why choose this sealant Seals metal threaded fittings for gas and water systems Fast handling strength in 10 to 20 minutes at room temperature Full cure in 24 hours for long lasting performance Resists vibration and helps prevent loosening Approved for gas service and type tested for contact with potable water Where to use Metal to metal threaded connections on gas lines and appliances Metal to metal threaded connections on cold and warm water pipes up to 55°C Not suitable for Plastic, glass, or rubber parts Non threaded gaps or joints exposed to air Continuous steam temperatures above 135°C Directions Remove oil and contamination from threads. Ensure parts are clean and dry. Apply sealant to one surface, covering 2 to 3 thread rotations. Assemble threads. Wipe off any excess sealant immediately. Allow 10 to 20 minutes for initial cure before pressurising. Allow 24 hours for full cure. Disassembly can be performed using standard hand tools. Good to know Anaerobic sealants cure when air is excluded between metal parts. Sealant exposed to air will not cure. Packaging is larger than contents to prevent in bottle curing. Net content is 50g. Always wipe away excess to avoid any metallic taste from uncured material in potable water systems. Apply with good ventilation. If contact occurs with eyes or skin, flush with clean water immediately. Store in a cool, dry place. Keep out of reach of children. Approvals and compliance Approved by the Australian Gas Association (Cert. No. 7583, Class III, 2000 kPa) Type Tested AS/NZS 4020 (PTT40067, SAI Global) Specifications Chemistry Anaerobic thread sealant for metal parts Pack size 50g Initial cure 10 to 20 minutes Full cure 24 hours Gas temperature range -10°C to +135°C Water temperature range Up to 55°C Pressure class Class III, up to 2000 kPa Substrates Metal to metal threads only What is included 1 x Boston Liquid Thread Sealant 50g tube.
$8.40
Aftek MDF Adhesive 250 ml Overview Aftek MDF Adhesive 250 ml is a high quality fast setting MDF adhesive set designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials MDF timber trims decorative profiles Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Use in ventilated areas between 10°C and 30°C. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Activator accelerates set in seconds to minutes. Full strength develops over several hours. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Remove overspray and uncured adhesive with suitable solvent. Use carefully to avoid staining. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$8.37
Poly Ultra Nails Construction Adhesive is a high strength, versatile adhesive designed for bonding a wide range of building materials both indoors and outdoors. It offers exceptional adhesion, easy application, and water resistance, making it a reliable choice for construction and renovation projects. Features High strength bonding suitable for multiple materials Repositionable for up to 20 minutes for precise alignment Waterproof once cured Ready to use straight from the cartridge Brown finish for a natural look Suitable Materials Concrete, brick, plasterboard, ceramics Plywood, particle board, aluminium Hardwood, softwood, steel, fibreglass Some plastics (pre-test recommended) Application Instructions Ensure surfaces are clean, dry, and free from dust, grease, or flaking paint. Cut the seal, fit the nozzle, and cut to the desired bead size. Insert into a caulking gun. For wall panelling and sheet flooring, apply 6mm beads along studs or joists in a zig-zag line at 40cm intervals. Bring surfaces together within 10 minutes and press firmly along glue lines. Reposition if needed within 20 minutes. Fix with nails, screws, or clamps for at least 24 hours to ensure bond strength. For contact bonding, apply to one surface, bring together, then separate for 3–5 minutes before rejoining. Clean tools and excess adhesive with mineral turpentine. Technical Information Coverage: Approximately 15 metres of 5mm bead Initial bond: Within 24 hours at 25°C Full cure: Up to 7 days Colour: Brown Important Notes Not suitable for mirrors, polystyrene foam, or continuous water immersion Avoid use on copper-based metals or metals exposed to direct sunlight heat Do not use for tightly clamped joints or heavy loads without mechanical fasteners Safety Information Use in a well-ventilated area and avoid breathing vapours Wear protective gloves and eye protection Keep away from heat, sparks, and open flames Keep out of reach of children If swallowed, do not induce vomiting — contact a doctor or Poisons Information Centre (AUST 131 126; NZ 0800 764 766) Contains 30% w/w liquid hydrocarbons
$4.85
Dunlop Roof Repair Waterproofing Adhesive 310ml Seal, stick and stop leaks on the spot. This highly flexible, silane modified adhesive and sealant bonds and seals even in wet conditions, making it a smart fix for urgent roof, gutter and pond repairs. Why you will love it Works in the wet and can be applied underwater for minor repairs Flexible waterproof seal for joints, cracks and patches Strong adhesive grab for quick spot fixes Paintable once cured to match surrounding surfaces Low mess clean up while wet Ideal surfaces Concrete, wall panels, timber, waterproofing membranes, ceramic tiles, aluminium, plastics, metal, polystyrene foam, glass and glazed tiles. Typical uses Emergency roof and gutter leak sealing Sealing laps, flashings and penetrations Pond edge and minor underwater touch ups General crack and joint sealing around the home Spot fixing where fast, reliable adhesion is needed Directions Prep: Ensure the surface is firm and free of dust, oil and loose residues. Slightly damp surfaces are acceptable. Load: Remove the aluminium seal, pierce the nozzle membrane, fit and trim the nozzle, then place the cartridge in a caulking gun. Apply as a sealant: Gun a continuous bead over the joint or crack and allow to cure. Apply as an adhesive: Gun bead lines or spots, then press parts together within 7 to 10 minutes at 23°C, before skinning starts. For spot fixing, keep glue points 25 to 30 cm apart. Clean up: Wipe away any excess while wet with a clean cloth. Good to know Application temperature: 5°C to 35°C Dry and cure times vary with substrate and climate. Higher humidity shortens open time, lower humidity extends it. Colour: Grey. Can be over painted once dry. Always test paint compatibility on a small area first. Shelf life: 12 months in unopened packaging stored in a cool, dry place Packaging: 310 ml cartridge Safety Wear gloves and eye protection. Avoid inhaling vapours and ensure good ventilation. If in eyes, rinse with running water and seek medical advice. Keep out of reach of children. Warranty Backed by a 10 year product guarantee when used as directed. This is in addition to your rights under the Australian Consumer Law. Notes Do a trial application for underwater or constantly wet repairs, as long term stability depends on the specific situation. Not for chemical resistant applications. Remove any skinned layer in the nozzle before reusing an opened cartridge.
$21.97
Tuff Turf Synthetic Grass Adhesive 320 g Overview Tuff Turf Synthetic Grass Adhesive 320 g is a high quality synthetic grass adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials synthetic turf backing seaming tape concrete compacted base plywood Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Install in dry conditions between 10°C and 30°C, avoiding heavy dew or rain. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Working time varies with conditions. Allow sufficient cure before foot traffic. Full strength typically within 24 to 48 hours. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean tools while wet with a suitable solvent or soapy water depending on formulation. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$12.76
SikaBond High-Strength Foam Construction Adhesive 750 mL is a reliable one component foam construction adhesive dispensed from a can chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 750 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Sika High-Strength for your next project Everyday jobs often involve mixed materials and imperfect surfaces. SikaBond High-Strength Foam Construction Adhesive 750 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Fixing studs, battens, and sheets Filling small gaps while bonding Fast installation where speed saves labour Suitable surfaces The adhesive works well on the following surface types when properly prepared: Timber and masonry Concrete and fibre cement Many building materials except PE and PP Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of assemble parts within the open time to ensure a strong bond. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Expands slightly to fill gaps, then cures to a firm, high strength foam. Provides excellent initial grab and reduces the need for nails in many applications. Temperature and environmental performance Apply within the can's specified temperature range. Humidity supports foam curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured foam with the prescribed cleaner. Once cured, cut back mechanically. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store cans upright. Do not expose to heat. Observe transport and disposal rules for pressurised containers. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$31.50
Sikaflex 258 Primerless Glass Adhesive 310 mL is a reliable polyurethane glass adhesive designed for primerless bonding to suitable automotive glass chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 310 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Sikaflex 258 for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Sikaflex 258 Primerless Glass Adhesive 310 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bonding glass where a primerless system is specified Automotive and transport glazing carried out by trained users Suitable surfaces The adhesive works well on the following surface types when properly prepared: Compatible glass substrates Painted frames and prepared bodywork per Sika guidance Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of observe skin time and install components within this window. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Moisture cure technology forms a strong, elastic bond. Skin forms first, followed by through cure depending on joint depth and humidity. Temperature and environmental performance Do not apply below the minimum stated on pack. Maintain adequate humidity for moisture cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Remove fresh adhesive with suitable cleaner. Once cured, trim with a sharp blade using care. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store cartridges cool and dry. Check use by dates before installation in critical work. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$37.49
Gorilla Ultimate Strong Wood Glue 532 mL is a reliable high performance wood glue for interior and exterior carpentry chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 532 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Gorilla Ultimate for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Gorilla Ultimate Strong Wood Glue 532 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Furniture build and repair Edge bonding and laminations Cabinetry and joinery where water resistance is valued Suitable surfaces The adhesive works well on the following surface types when properly prepared: Hardwoods and softwoods Plywood and MDF Veneers and end grain with correct technique Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of typically 5 to 10 minutes depending on temperature. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Open time allows assembly before clamping. Forms a strong cross linked bond that is water resistant when fully cured. Temperature and environmental performance Use above 10 C and avoid freezing conditions while curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wipe squeeze out with a damp cloth while wet. Scrape or sand once cured. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Close the cap tightly and store upright. Do not allow the nozzle to clog; remove dried film if present. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$25.20
Key features Dries clear for a neat, invisible finish Non toxic and low odour Water based for easy clean up before curing Suitable for brush or nozzle application Paintable when dry Strong bond on porous surfaces Ideal for Paper, cardboard, photos, and scrapbooking Craft foam, felt, and fabric edge bonding Balsa wood and other light timbers School and hobby projects Directions Ensure surfaces are clean, dry, and free of dust or oil. Apply a thin, even coat to one surface. For very porous materials, coat both surfaces. Join pieces while the glue is wet and press firmly. Clamp or weight if needed. Wipe away excess with a damp cloth. Allow to set. Light handling is typically possible after 30 to 60 minutes. Full strength develops after 24 hours. Clean up Clean tools and fresh spills with a damp cloth. Once cured, scraping or sanding may be required. Handy tips For stronger joints on timber, lightly sand and dry fit pieces before gluing. Avoid excessive glue, which can lead to slow drying and warping on thin paper. Not suitable for continuous water immersion or load bearing joins. Storage Replace cap after use. Store upright in a cool, dry place away from frost and direct heat. Safety Non toxic formula. If irritation occurs, discontinue use. Technical details Base PVA emulsion Appearance White, dries clear Viscosity Medium, smooth flow Open time Up to 10 minutes depending on surface and coat weight Set time Approx. 30 to 60 minutes Full cure 24 hours Water resistance Not recommended for prolonged moisture exposure Paintable Yes, once fully dry
$11.30
Get fast and reliable adhesion with Bostik Quick Glu Instant Fix Bond Spray. This 25g spray adhesive provides a strong, clear and lasting bond suitable for a wide range of materials used in craft, home and office projects. Key Features Instant bonding for quick and easy use Dries clear for a neat and professional finish Acid free formula that resists yellowing over time Works on wood, metal, ceramic, leather, paper and many plastics (not suitable for polyethylene or polypropylene) Compact 25g size ideal for small jobs and easy storage How to Use Ensure surfaces are clean, dry and free from grease or dust. Shake the can well before each use. Hold the can 15 to 20 cm from the surface and apply a light, even coat. Wait a few seconds until tacky before joining the surfaces. Press firmly together and hold for a few seconds for best results. After use, clear the nozzle by spraying briefly while holding the can upside down. Recommended Applications Arts and crafts projects DIY home repairs Paper, cardboard, leather and wood bonding Quick fixes requiring a clear and clean finish Safety and Storage Use only in well ventilated areas and avoid inhaling vapours. Keep away from heat, sparks and open flames as the product is flammable. Store in a cool, dry place away from direct sunlight. Keep out of reach of children. Bostik Quick Glu Instant Fix Bond Spray delivers a convenient and efficient solution for fast bonding on a wide variety of materials.
$8.50
Bostik Hobby Craft Dual Tip Liquid Glue 30ml is the perfect choice for creative projects, crafts, and schoolwork. Designed for precision and versatility, this liquid glue features two applicator tips, a fine tip for detailed work and a broad tip for larger surfaces. The smooth, clear formula ensures a clean, professional finish without clumping or streaks. Dual applicator design: Fine and broad tips for all craft needs Clear drying: Leaves no visible residue Ideal for: Paper, cardboard, photos, and light craft materials Easy to use: Non-toxic, washable, and child-friendly Perfect for school and home projects This handy 30ml bottle is compact and easy to store, making it a must-have for hobbyists, students, and anyone who loves crafting. Its dual-tip applicator provides control and convenience whether you're gluing delicate details or covering larger areas. Applications: Arts and crafts, card making, scrapbooking, paper modeling, and DIY projects. Brand: Bostik
$5.88
Bostik Super Glue Instant Bond gives you fast, reliable fixes for everyday repairs. Each pack includes three 1 mL single-use tubes to keep the adhesive fresh and reduce clogging, so you only open what you need. Why you’ll love it Sets in seconds for quick repairs High strength, clear finish Precise nozzle for controlled application Three single-use tubes to minimise waste Best for Metal, most plastics*, rubber, ceramic, porcelain Wood trims, leather, cork, card, paper Small household, craft, hobby and DIY fixes How to use Ensure surfaces are clean, dry and close-fitting. Lightly sand smooth or glossy areas. Pierce the tube seal, fit the nozzle and apply a tiny drop to one surface. Press parts together firmly for 10 to 60 seconds. Support if needed until handling strength is reached. Allow a few hours for maximum strength before stressing the bond. Good to know Finish: Clear Chemistry: Cyanoacrylate Viscosity: Liquid for close-fitting parts Gap fill: Very low. Parts should mate tightly. Tips Less is more. Excess can slow curing and reduce strength. Store unopened tubes upright in a cool, dry place. Use each tube once opened. For porous or flexible materials, consider a flexible or gel adhesive. Limitations Not suitable for PP, PE, PTFE, silicone, glass aquariums or very oily surfaces* Not recommended for large gaps, continuous water immersion or high heat exposure *Some plastics may require a primer. Always spot test first. Safety Bonds skin and eyes in seconds. Wear protection and keep out of reach of children. Use with adequate ventilation. If spilt on skin, do not pull; soak in warm soapy water and gently roll apart. What’s in the pack 3 x 1 mL single-use tubes of clear cyanoacrylate adhesive
$8.82
Bostik Super Glue Gel is a fast setting, non drip adhesive that stays where you put it for precise, clean bonds. The thixotropic gel formula is ideal for vertical surfaces and small gap filling, delivering reliable results on everyday repairs and crafts. Key features Fast setting gel for controlled application Non drip formula for vertical and overhead surfaces Small gap filling for close fitting parts Strong bond on many common materials Clear finish for neat repairs Ideal for Metal, rubber, most hard plastics, wood, ceramics, porcelain Small household repairs, models, craft and DIY fixes Precision bonding where liquid super glue may run Not suitable for Polyethylene, polypropylene, PTFE Very flexible materials or items regularly exposed to water immersion Food contact surfaces or aquarium use Directions Ensure surfaces are clean, dry and close fitting. Lightly roughen smooth surfaces if possible. Remove cap and apply a small bead of gel to one surface. A little goes a long way. Join parts immediately and hold firmly until set. Avoid moving the bond during curing. Allow the repair to rest for several minutes before light handling and longer for full strength. Handy tips Test on an inconspicuous area first. Use sparingly. Excess adhesive can slow cure. For porous materials, a second application may improve the bond. Clean up Wipe fresh squeeze out immediately. Once cured, carefully remove excess with a sharp blade. Adhesive may whiten on some surfaces if excess is left to cure. Storage and safety Close cap tightly after use and store upright in a cool, dry place. Bonds skin in seconds. Wear care when handling. If skin bonding occurs, do not pull apart. Soak in warm soapy water and gently roll apart. Use in a well ventilated area and keep out of reach of children.
$6.47
Bostik Hard Plastics Glue is a clear, fast-setting adhesive designed for rigid plastic repairs around the home, garage, and workshop. It forms a strong, durable bond that resists impacts and everyday handling while drying clear for a neat finish. Best for ABS, PVC, acrylic, polycarbonate, polystyrene Household repairs, toys, car trim, appliance covers Small craft fixes and model making Not suitable for Polyethylene or polypropylene PTFE or silicone surfaces Surfaces that are oily, dusty, or wet Key features Clear finish that blends with most plastics Fast initial grab with strong final cure Impact and vibration resistant Precision nozzle for controlled application Surface preparation Ensure surfaces are clean, dry, and free from dust, grease, or release agents. Lightly roughen glossy plastic with fine sandpaper to improve adhesion, then wipe clean. How to use Test on a small hidden area first. Apply a thin, even layer to one surface. Avoid excess. Join parts immediately and hold firmly for 30 to 60 seconds. Allow to set undisturbed. Handling strength is typically reached within minutes. Full cure develops over 12 to 24 hours depending on temperature and humidity. Tips For tight fitting parts, less is more. A thin film gives the strongest bond. Use clamps or tape to maintain alignment while the adhesive sets. Cleanup Wipe fresh adhesive immediately with a suitable solvent on a cloth. Cured residue may need careful mechanical removal. Storage and safety Replace cap after use and store upright in a cool, dry place. Use in a well ventilated area. Avoid skin and eye contact. Keep out of reach of children.
$12.72
Bostik Repair All is a clear, multi-purpose adhesive for quick, durable repairs around the home, garage, and workshop. It bonds strongly, remains slightly flexible, and is water resistant once cured, making it suitable for everyday fixes and craft projects. Why you will love it Strong, long lasting bond Dries clear for a neat finish Water resistant once fully cured Flexible bond helps absorb vibration Suitable for indoor and outdoor use Works on Metal, wood, ceramics, glass, most rigid plastics, rubber, leather, fabric, and more. Always test on delicate or unknown materials first. Ideal for Household repairs and DIY Craft, hobbies, and school projects Fixing ornaments, toys, trims, and fittings Directions Ensure surfaces are clean, dry, and free of dust or grease. Lightly roughen smooth surfaces. Apply a thin even layer to one surface. Join parts together and press firmly. Support or clamp if needed. Wipe away any squeeze out immediately with a cloth dampened with solvent suitable for the substrate. Allow to set undisturbed. Handling strength is typically reached within hours. Full cure is usually achieved after 24 hours depending on bead size, temperature, and humidity. Clean up Uncured adhesive can be removed with a suitable solvent. Cured adhesive is best removed mechanically by trimming or carefully scraping. Good to know Not recommended for polyethylene, polypropylene, PTFE, or surfaces that will be in constant water immersion. Avoid contact with food or drinking water surfaces. Store upright in a cool dry place with cap tightly closed. Key details Brand Bostik Product Repair All Appearance Clear when dry Finish Flexible Water Resistance Yes, once cured Pack Size 20ml Always read the label and follow safety instructions. Keep out of reach of children.
$14.50
Keep your glue gun ready for any project with the Bostik HG3 Glue Gun Refills. These high quality hot melt sticks provide a smooth, even flow for clean and reliable bonding. Pack of 10 clear adhesive sticks Compatible with Bostik HG3 Glue Gun Creates a strong, flexible and transparent bond Suitable for wood, plastic, fabric, leather, ceramics and more Perfect for craft work, household repairs and DIY projects. The hot melt formula ensures quick adhesion with minimal mess, giving you professional results every time. How to use: Insert a glue stick into the back of your glue gun. Allow the gun to heat for a few minutes before use. Apply steady pressure on the trigger to release glue. Join surfaces immediately for best results. Let the glue cool completely before handling. Safety Information: Hot glue can cause burns. Avoid contact with skin and eyes. Keep out of reach of children. The Bostik HG3 Glue Gun Refills are ideal for quick fixes, decorative projects and reliable everyday bonding.
$15.21
Bring Your Leather Items Back to Life Restore your favourite leather goods such as shoes, belts, bags, and upholstery with confidence using Bostik Leather Repair Glue. This precision adhesive delivers a strong, flexible, and water-resistant bond that dries crystal clear. Key Features Ultra strong and long lasting bond for real and imitation leather Flexible and clear finish with no visible residue Resistant to water and heat up to approximately 60 °C Precision application through fine nozzle squeeze tube Multi material versatility suitable for leather, PVC, felt, canvas, some plastics, wood, and metal How to Use Ensure surfaces are clean, dry, and free from dust, oil, or old adhesive residue. For leather surfaces, avoid applying to the shiny side to prevent marks. Apply a thin film of glue to one surface. For non porous materials, apply to both surfaces. Press the surfaces together firmly. The bond sets almost instantly and reaches full strength in about 24 hours. Replace the cap immediately after use to prevent the tube from drying out. Tips and Care For best adhesion, lightly roughen smooth or shiny surfaces with fine sandpaper before gluing. Avoid stressing the repair before full cure. To remove unwanted glue, use acetone or nail polish remover on a small hidden area first. Technical Specs and Safety Form: Clear solvent based polyurethane adhesive Heat resistance: up to approximately 60 °C Highly flammable. Keep away from heat, sparks, and flame. Always follow manufacturer instructions and safety guidance. Use in a well ventilated area, wear protective gloves, and avoid contact with skin or eyes. Packaging Size: 20 mL tube
$9.79
Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load):– At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area– At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.
$21.74
You have seen 48 out of 200 products
Products designed for precision nozzle application, allowing narrow beads and spot placement without mess. Useful for trims, electronics, hobby work and hard-to-reach joints. Select standard or fine tips to control flow and bead size. Use filters to refine by chemistry, cure speed and clean-up. Always check the product page and TDS/SDS for usage notes and compatibility.
