High Temperature Resistant

PC-Fahrenheit™ Putty Epoxy is the choice for temperatures up to 260° C. It is supplied as a premeasured stick that you mix with fingers. Fast curing (60 min). Best for steam heat applications. A toolbox must. Great on copper and iron. Here are just a few specific uses (there are hundreds of other uses): Seal cracked steam or hot water radiator Stop leaking steam fittings Fill hole in heat exchanger Attach thermocouple to hot surface Seal chimney ductwork How to prepare a surface for bonding with PC-Fahrenheit™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Fahrenheit™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Fahrenheit™ repair a leaking steam radiator? PC-Fahrenheit™ resists higher temperatures and is suitable for repairing steam pipes and radiators. Can PC-Fahrenheit™ be used in a fireplace or wood burning stove? PC-Fahrenheit™ will withstand temperatures up to 260°C. A fireplace or wood burning stove creates temperatures exceeding 260°C. Can PC-Fahrenheit™ be used to seal heater chimney duct? PC-Fahrenheit™ is excellent for use on sheet metal and the temperature is within an acceptable range. Can PC-Fahrenheit™ seal a rust hole in barbecue grill? PC-Fahrenheit™ can be used on the barbecue grill exterior but is not recommended for the interior. How long should PC-Fahrenheit™ be mixed before applying? Mix PC-Fahrenheit™ for 45 to 60 seconds then immediately apply. What is the temperature limit? PC-Fahrenheit is not intended to exceed 260°C. -  Will PC-Fahrenheit™ burn? PC-Fahrenheit™ is not flame resistant and may burn if exposed to direct flame. Does PC-Fahrenheit™ stick to car radiator? Car radiators are made of various metals and plastic composites. Test for adhesion and test for leaks.

Read more less

Premium one component room temperature vulcanising silicone sealant USE Fridge and freezer sealing Pizza oven sealing Oven sealing Aluminium Glass CHARACTERISTICS AND ADVANTAGES High temperature resistance (-50 to 250OC) Excellent adhesion Gap filling properties Heat proof Vibration resistant Highly versatile PACKAGING: 300 ml cartridges COLOUR: Black SikaSeal® Appliance Silicone Sealant is a premium one component room temperature vulcanising (RTV) silicone rubber designed for flexible gasketing and sealing applications. SikaSeal® Appliance Silicone Sealant forms a tough but flexible seal of all shapes and sizes and fills any surface voids. The cured product can withstand vibration, weathering, temperature extremes, water oil and grease without hardening, shrinking or cracking. Uses  Fridge and freezer sealing  Pizza oven sealing  Oven sealing  Aluminium  Glass Characteristics / Advantages  High temperature resistance (-50 - 250°C)  Excellent adhesion  Heat proof  Gap Filling properties  Vibration resistant  Highly versatile Product Data Colour Black Packaging 300ml Cartridge, 12 cartridges per box Storage 18 months from date of production if stored in undamaged and unopened original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base 1-C silicone Density (uncured) 1.0 kg/l approx. Skin Time 10 min approx. Tack-free time 20 min approx. Curing Time 24 hours approx. Cure Mechanism Moisture-curing Cure Type Acetoxy Application temperature 5 - 45°C Mechanical/Physical Properties Tensile Strength 1.0 N/mm2 approx. Shore a Hardness 25 approx. Ultimate Elongation 600% approx. Application Details Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue-free solvent and allowing drying properly. Cut the nozzle at a 45° angle to the desired bead size (3 mm is suitable for most applications) then apply a continuous and even bead along the joint. Cure Mechanism SikaSeal® Appliance cures by reaction with atmospheric moisture. The reaction thus starts at the surface and proceeds to the core of the joint. The curing speed depends on the relative humidity, temperature and thickness of the sealant. At low temperatures, the water content of the air is lower and the curing reaction proceeds more slowly. Clean Up Uncured, excess SikaSeal® Appliance may be removed with Sika® Remover-208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife. Application Conditions/ Limitations Restrictions On Use SikaSeal® Appliance is not recommended for use in applications where it will be permanently exposed to temperatures exceeding 250°C or in contact with fuels. The above information is offered for general guidance only. 

Read more less

LOCTITE 263 is designed for the permanent locking and sealing of threaded fasteners. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. It's particularly suited for heavy duty applications such as studs into motor housings, nuts onto studs in pump housings and other fasteners where high strength is required. LOCTITE 263 provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids. Recommended on High strength Locks studs against vibration loosening Controlled/torque tension Prevents thread corrosion Fast curing How to use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole.  For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours.  Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush.  For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 4. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 5. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 6. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 7. Assemble and tighten as required For Disassembly 1. Apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush

Read more less

For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 85-86 Thread Sealant High Temperature Anaerobic Adhesive 50ml Loxeal 85-86 is a high strength anaerobic adhesive for locking and sealing threaded joints on all metals, in both free and forced matings. It maintains its sealing performance up to +200°C and offers high resistance to thermal shock, vibration, water, gas, oils, fuels, refrigerant fluids and many other chemicals – making it the choice for hot pipework, gas lines and demanding sealing jobs where standard sealants fall short. Why choose Loxeal 85-86? Seals and locks in one step with high mechanical strength Keeps sealing up to +200°C (service range -55°C to +200°C) Works on all metals, including free and press-fit assemblies Resists thermal shock, vibration, fuels, refrigerants and many chemicals Generous gap fill up to 0.30 mm on threads up to M56 / 2″ Green colour, fluorescent under blue light, for easy inspection Certified and approved Approved for gas-tight threaded joints to EN 751-1 (DIN-DVGW) WRAS approved for contact with wholesome (potable) water Compliant with the UBA (German Environment Agency) declaration for potable water use BAM certified as a sealant in the presence of gaseous oxygen up to 20 bar at +60°C Typical applications Sealing threaded joints on gas, steam, hot water and heating pipework Potable water fittings (observe the potable-water cure times below) Refrigeration, fuel and industrial fluid lines exposed to heat and vibration How to use Clean and degrease both threads with Loxeal Cleaner 10 and allow to dry. Apply a continuous bead circumferentially, 1–2 threads back from the leading edge, using enough product to give a complete seal. Assemble and tighten the joint, then wipe off any uncured excess. Allow to cure before pressurising. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 (this may reduce final strength). Cure times at +25°C Handling strength: 10–40 minutes Functional strength: 6–12 hours Full cure: 24–36 hours Before contact with potable water: allow 24 hours at +20°C for brass, copper and cast iron; 7 days for stainless steel and aluminium Specifications Chemistry Anaerobic methacrylate Colour Green (fluorescent under blue light) Viscosity (+25°C) 2,200–4,000 mPa·s Specific gravity (+25°C) 1.05 Max thread size / gap fill M56 / 2″ / 0.30 mm Shear strength (ISO 10123) 15–25 N/mm² Breakaway torque (ISO 10964) 25–35 N·m Prevailing torque (ISO 10964) 40–55 N·m Service temperature -55°C to +200°C Shelf life 1 year in original unopened packaging at up to +25°C Important notes Recommended for metal thread joints only – contact a technical service before use on other materials. Do not contaminate the adhesive with metal; cut the nozzle to the required bead size. The liquid product can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. High strength – for disassembly, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

A premium grade high strength construction adhesive that delivers a consistently strong bond on mirror, metal and glass material. Uses Ideal for adhering mirrors to walls, metal letterboxes to exterior walls, house numbers to exterior walls, bathroom fixtures to tiles, tool holders on metal shed walls etc. Liquid Nails Mirror, Metal, Glass is also suitable for use on BHP decorative sheet metals such as Lysaght, Zincalume, Colorbond®, Marviplate®, galvanised metals, Alcan and Comalco aluminium systems. Technical Features Will not discolour mirrors Heat and steam resistance Adheres metal, glass and mirror well to most surfaces including painted surfaces but not wall coverings Adheres and forms a durable seal between sheet metals Gap filling on uneven surfaces Forms flexible/shock resistant bonds UV resistant Low odour during application Non corrosive Weather resistant Application Tips All surfaces must be clean, dry and free from dirt dust, oil and loose rust. Clean surfaces with mineral turpentine and wipe dry with a clean rag before applying. Painted surfaces should not be flaky or peeling. Cut tip off cartridge and cut nozzle to suitable size opening (approximately 5mm). Fit nozzle to cartridge. Place cartridge into caulking gun. Support bond until adhesive cures sufficiently (at least 48 hours adhesive cures at 2mm depth per day). APPLICATION FOR MIRRORS For mirrors up to 6mm thick, apply strips of adhesive 5cm from edges and approx 8cm apart When mirror is pressed onto the wall, strips of adhesive must not spread into, or touch one another. A gap must remain between them. Immediately after applying adhesive, place mirror against wall before adhesive skins (within 5 minutes) The weight must be supported and mirror must be held in place with temporary supports (e.g. with clips or tape) to hold and maintain adhesive contact over the total bond area until sufficient adhesive strength has developed. Normally after 72 hours. Do not seal around the edges of the mirror for at least a week to allow air circulation and aid the adhesive fully cure Mirrors should not be fixed directly to unpainted plaster, timber, concrete or brick walls. These surfaces should be painted to prevent potential damage to mirror. Painted surfaces should not be flaking or peeling. Not recommended for fixing vinyl back mirrors If in doubt, conduct an adhesion test by curing a little adhesive onto mirror backing for 24 hours. If adhesive can be peeled off, do not proceed. GENERAL APPLICATION Apply as for mirrors and press surfaces together immediately Leave ‘squeeze out ‘ to cure and trim (avoid cutting into the bond) Support bond until adhesive cures sufficiently (normally after 72hrs). Adhesive cures at 2mm depth per day. Technical Details and Performance Indicative information only, not to be used for setting specifications. Consistency (As applied) Non-slump, solvent free paste Curing Mechanism Very rapidly develops an adhesive bond by reaction with moisture from the air Curing Rate 2mm depth per day Skin Forming Time 5-10 minutes (depending on weather conditions) Service Temperature –60°C to +150°C Lap Shear Bond Strength (Aluminium to Aluminium at 1.6mm thick adhesive, 500sq mm bond area) After 24 hrs: 280KPa After 48 hrs: 550KPa After 7 days: 830KPa Coverage 15 metres of a 5mm diameter bead Cleaning Clean all excess adhesive from equipment before it cures with a cloth dampened with mineral turpentine or acetone. Once cured adhesive is extremely difficult to remove and must be abraded or trimmed with a knife

Read more less

Features Resists intense heat Sets hard Water clean up Where can this product be used? Repairing bricks in fireplaces and chimneys Sealing flues in pot-belly stoves Filling cracks in ironworks and bricks  What materials is this product suitable for? Brick Metal Concrete How to Use: Remove all dust, grease and loose debris before applying material. Dampen the cavities on porous surfaces for better adhesion. Apply Fireproof Cement firmly into holes and cracks with a damp knife or spatula. Allow Fireproof Cement to dry a minimum of 48 hours before exposure to heat. If Fireproof Cement is stiff slacken with a little water. Limitations: Fireproof Cement is not an adhesive - it is a filling compound. Not recommended for external use e.g. BBQ's, incinerators etc. Fireproof Cement is not suitable for use in kilns. Fireproof Cement is not recommended for moving joints such as expansion joints as it sets rigidly Hardened material cannot be resoftened with water.

Read more less

Silicone 401 RTV is a one part ready to use, acid cure, room temperature vulcanising (RTV), silicone adhesive sealant. It cures rapidly on exposure to atmospheric moisture to form a versatile, durable, resilient silicone rubber. It is available in clear. Uses Silicone 401 is suitable for form-in-place gaskets and for adhesive, sealing and electrical insulating applications in manufacturing and plant maintenance. Technical Features Wide Temperature Tolerance: Remains permanently flexible under operating temperatures from – 60oC to 205oC, and will tolerate short periods of 260oC Good Chemical Resistance: Good resistance to most organic and inorganic chemicals, solvents and oils Primerless Adhesion: Adheres without primer to many metal, glass, ceramic, rigid plastic, rubber painted and wood substrates Non-toxic: Suitable for incidental food contact in food handling equipment and food contact surfaces Excellent Weatherability: Excellent resistance to ozone, UV light and ageing Good Electrical Insulating Properties: Insulating properties are comparable to other insulating rubbers at room temperature, though performs better than many other rubbers at higher temperatures and water has little effect on these properties Application Tips Not recommended for use with petrol, distillate and some other hydrocarbon solvents. These can cause softening and swelling which is undesirable in some applications. Do not use in totally confined joints where sealant is not exposed to atmospheric moisture Chemical compatibility should be tested for each application under consideration Cannot be over-painted Technical Details and Performance Indicative information only, not to be used for setting specifications. Typical Application Properties Consistency Non – sag, gun grade Tack Free Time (25oC, 50% r.h.): 15 – 20 minutes Skin Forming Time 5 to 10 minutes (depending on weather conditions) Cure Time (3mm Section @ 25oC, 50% R.H.): 24 hours Shrinkage During Curing Approximately 3.5% by volume Specific Gravity 1.04 Storage Life (Below 30oC in original unopened container):12 months Typical Mechanical Performance Properties (3 day cure @ 25oC, 50% R.H.) Tensile Strength (MPa) 1.2 Ultimate Elongation % 400 Hardness (Shore A) 25 Tear Strength (N/mm) 5.0 Joint Movement Capability ± 25% Typical Electrical Properties (at Room Temperature) Dielectric Strength kv/mm 21 Dielectric Constant @50Hz to 5MHz 2.6-2.8 Dissipation Factor Tan @50Hz-5MHz 20×10-4 to 5×10-4 Volume Resistivity (ohm-cm) 1×1013 (wet 60oC) 1×1014 (dry 23oC) Typical Thermal Properties Brittle Point –60oC Maximum Continuous Operating Temperatures 205oC Maximum Intermittent Operating Temperatures 260oC

Read more less

PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.

Read more less

Boston Premium PTFE Plumbers Pink Thread Seal Tape is a trade-focused thread sealing tape for water pipe fittings, supplied here as a bulk pack of 10 rolls for plumbers who get through plenty of tape. Each roll is 12mm wide and 10m long, and the pink colouring makes it easy to tell apart from other tapes on the truck or in the toolbox.About the formulaThis is a PTFE (polytetrafluoroethylene) film tape that fills the gap in tapered pipe threads to help prevent leaks at threaded joints. It was developed in Australia for professional plumbers, and it is WaterMark approved to WMTS 014:2016 (licence WMK26374). The tape has a density of 0.8g/cm³ and handles a wide temperature range, from -190°C to +310°C, so it suits both hot and cold water lines.Where to use itIndoors: threaded fittings on domestic and commercial water lines, such as taps, valves, unions and connectors.Outdoors: threaded water connections on garden and irrigation lines and other exposed pipework.Suitable for the threaded joints of water pipe fittings. Pink tape is intended for water use, so choose a tape that is rated for gas on any gas fitting.How to use itMake sure the male thread is clean and dry, and free of old tape, oil and debris. Hold the end of the tape on the thread and wrap it around the thread in the direction the fitting will tighten, so the tape does not unwind when the joint is made up. Overlap each turn slightly, keep the tape pulled snug so it presses into the thread grooves, and leave the first thread clear. Tear off the tape, press the end down, then assemble the joint and tighten as normal.Important notesDo not over-tighten, as this can damage fittings. If a joint leaks after assembly, undo it, remove the old tape and rewrap with fresh tape rather than adding more on top. Follow your local plumbing regulations and the fitting manufacturer's instructions for the job.Specifications Brand Boston Product Premium PTFE Plumbers Pink Thread Seal Tape Pack 10 rolls, each 12mm x 10m Colour Pink Material PTFE Density 0.8g/cm³ Temperature range -190°C to +310°C Application Hand wrapped onto threads Standards WaterMark approved, WMTS 014:2016, WMK26374 Use Hot and cold water pipe threads SafetyUse with normal care and keep the work area tidy so loose tape offcuts do not end up in pipework. Keep out of reach of children and store the rolls in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Dingo Fire Rated Mortar is a ready-to-mix, rapid setting cement mortar made for the high heat areas of pizza ovens, fireplaces and barbeques, supplied here as a 10kg bag. It suits both new builds and patch repairs, so you can use it to build a heat-exposed structure or to fix up an existing one.About the formulaA cement-based dry mix made from high temperature resistant alumina cement and graded aggregates. You only add clean water, and no other components are needed. The manufacturer rates it for heat resistance up to 800°C, referencing AS 1530.1:1994 (R2016). Once mixed, it sets quickly: the initial set takes about 2 hours and the final set about 3 hours.Where to use itIndoors: fireplaces and chimneys, including building them and patching existing masonry.Outdoors: pizza ovens and barbeques, both new construction and repairs to existing structures.It is intended for masonry heat-zone work such as pizza ovens, barbeques, fireplaces and chimneys. For any other material or use, check with the manufacturer first.How to use itLay out your project and have all your tools ready before you open the bag. Make sure surfaces are clean, sound and free from oil, grease and loose particles. Tip the amount you need into a clean bucket, then add clean water gradually. A 10kg bag needs roughly 1.6 to 1.7 litres of water. Mix mechanically for at least 3 minutes, using a low speed electric drill with a paddle mixer, until the mix is thorough and even. Use the contents as soon as you can after opening the pack. A 10kg bag makes roughly 6 to 6.5 litres of mortar.Important notesMix only what you can use within the setting window, as the mortar begins to set after about 2 hours. The bag holds 10kg net of dry product, so take care when lifting it. Poor manual handling can cause injury. Prolonged skin contact with the wet mix may cause irritation, dermatitis or alkaline burns.Specifications Brand Dingo Product Fire Rated Mortar Pack 10kg bag (dry powder) Colour Grey Base Cement based (alumina cement and graded aggregates) Application Mix with water and apply as mortar for new construction or patching Mixing water About 1.6 to 1.7L per 10kg bag Yield About 6 to 6.5L of mortar per 10kg Set time Initial set 2 hours, final set 3 hours Heat resistance Up to 800°C Standard referenced AS 1530.1:1994 (R2016) Use Pizza ovens, fireplaces, barbeques and chimneys SafetyThe wet mix can irritate the eyes and skin, and the manufacturer notes that prolonged exposure may cause dermatitis and alkaline burns. Avoid contact with eyes and skin, and take care when handling the 10kg bag. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Sika Sikasil Auto is a neutral-cure, one-component silicone adhesive sealant made for vehicle repair and trim work, supplied here in a handy 75g tube. It forms a permanent, flexible bond or seal on a wide range of automotive materials, and the cured rubber copes with sunlight, salt spray, temperature swings, vibration and regular car-wash products without hardening, shrinking or cracking.About the formulaA moisture-curing, one-component silicone with a neutral cure, so it does not give off the acidic smell of acetic silicones and is described by the manufacturer as non-corrosive. It cures by reacting with moisture in the air, starting at the surface and working into the core of the joint. Cure speed depends on humidity and temperature, and it cures more slowly in cold conditions. Once cured it is a soft, stretchy rubber with strong thermal, UV, weathering and vibration resistance, and it stays serviceable from -50°C up to 250°C.Where to use itIndoors: bonding small interior components and trim, sealing joints, and cutting down noise and vibration inside the vehicle.Outdoors: sealing and bonding small exterior parts and joints on cars and other vehicles where weather, UV and salt spray are a concern.Suitable materials include fibreglass, metals, most plastics, glass and painted surfaces. Always test on the actual substrates and under your real conditions first to confirm adhesion and material compatibility.How to use itApply at ambient temperatures between 5°C and 45°C onto clean, dry surfaces that are free of oil, grease and dust. Run the sealant into the joint or onto the part and assemble or tool it before it skins over. At 23°C and 50% relative humidity it skins in about 10 minutes and is tack free in about 20 minutes. Excess uncured sealant can be wiped off with Sika Remover-208 or a similar product. Cured sealant has to be trimmed or scraped away mechanically. If you get it on your skin, wash straight away with SikaCleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin.Important notesSikasil Auto cannot be overpainted, so complete any painting before sealing or mask the area. It cures to a depth of about 3 mm in 24 hours, so deeper joints and thicker beads take longer. Check the manufacturer's data sheet for any surfaces or applications where the product is not recommended. This product is designed for vehicle applications. Test first on a small area before committing to the full job.Specifications Brand Sika Product Sikasil Auto Multipurpose Automotive Adhesive Sealant Pack 75g tube Colour Translucent Chemical base 1-component silicone, neutral cure, moisture-curing Application Tube, applied by hand Application temperature 5 to 45°C ambient Skin time About 10 minutes (23°C, 50% r.h.) Tack free time About 20 minutes (23°C, 50% r.h.) Cure speed About 24 hours to a 3 mm depth Density (uncured) 1.0 kg/L Shore A hardness 30 Tensile strength 1.0 N/mm² Elongation at break 600% Service temperature -50 to 250°C Shelf life 18 months when stored below 25°C Use Vehicle interior and exterior SafetyFollow normal good practice for silicone sealants: work in a well-ventilated area, wear gloves and eye protection, and keep out of reach of children. Wash skin promptly after contact using an industrial hand cleaner and water, and do not use solvents on skin. Store in the original sealed tube below 25°C. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

The Deks Dektite Premium #7 is a red silicone roof flashing for sealing larger pipe, flue and vent penetrations through metal roofing, supplied here as a single unit that suits pipes from 150mm to 300mm. A flexible silicone cone fits snugly around the pipe, and a formable aluminium edge lets the large square base follow the shape of your roof sheeting. It is built for the heat, UV and weather swings of Australian roofs.About the productThe cone is moulded from red silicone polymer. Deks rates it for constant temperatures at the roofline from -50°C up to 200°C, so it also suits hot flues and exhausts as well as cold pipes. The cone is designed to hold firm contact against the pipe wall for a watertight seal. The malleable aluminium edge bends to match corrugated and ribbed profiles. The wide 456mm square base gives you a more forgiving fit over a larger or slightly untidy opening. Deks lists UV testing, BAL 29 and other certifications for the range on its product page.Where to use itIndoors: not applicable, this is a roof-top flashing. It is fitted from the outside where the pipe leaves the building.Outdoors: single pipe, flue, vent, exhaust or similar round penetrations on metal roofs, including hot-flue applications that suit the temperature range above.Suitable for a single round penetration with an outside diameter of 150mm to 300mm on metal roof profiles. Check the pipe size before you order, as the cone is trimmed to fit and cannot be made larger.How to use itMeasure the outside diameter of the pipe and trim the silicone cone with sharp shears at the matching point so it grips the pipe snugly. Slide the flashing down over the pipe and bend the aluminium edge to match the roof profile. Fix the base to the roof with suitable screws and seal as recommended by the manufacturer. Check that the cone sits tight against the pipe and that the base follows the sheeting with no gaps.Important notesAlways follow the Deks installation instructions for your roof profile and pipe. Wear gloves when handling the aluminium edge, as trimmed and formed edges can be sharp. This product is a flashing, not a sealant, and the base should be fixed and sealed with fasteners and sealants suited to your roof. If you are unsure about fitting to hot flues or in bushfire-prone areas, check the relevant requirements or ask a licensed roofer or plumber.Specifications Brand Deks Product Dektite Premium #7 Red Silicone Roof Flashing Pack 1 flashing Pipe outside diameter 150mm to 300mm Base size 456mm x 456mm (square) Overall height About 99mm Colour Red Material Silicone cone with formable aluminium base Temperature range at roofline -50°C to 200°C (constant) Roof pitch 0 to 45 degrees Use Exterior, metal roofs SafetyTake normal care when working at heights and use fall protection where required. Wear gloves and eye protection when cutting the silicone cone or bending the aluminium edge. Keep offcuts away from children and pets. Refer to the manufacturer for any safety information supplied with the product. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Boston Silicone Self-Fusing Tape in black is a 3 metre roll of stretchy repair tape made for quick fixes on leaking pipes and hoses. It fuses to itself as you wrap it, so there is no glue involved. It forms a watertight and airtight wrap, which makes it a handy emergency item for the plumbing kit, the toolbox or the shed.About the formulaThis is a silicone tape with no adhesive coating. It bonds only to itself, which means it does not leave sticky residue and can be removed cleanly when the job is done. The tape stretches well beyond three times its length, and that stretch is what lets it pull tight around pipes, hoses and fittings. It is rated for a very wide temperature range, from -55°C to +260°C. The black colour hides dirt and grime and blends in with black fittings.Where to use itIndoors: temporary sealing of weeping pipes, hose joins and fittings around the laundry, bathroom, kitchen or workshop; adding a comfortable, slip-resistant grip to tool handles.Outdoors: emergency repairs on garden hoses and tubing, and general fast fixes around the home, garden or workshop.The tape is designed for wrapping around pipes, hoses, fittings and tool handles. It is a multipurpose repair tape, so it also suits many other small wrap-and-seal jobs.How to use itMake sure the area you are repairing is clean and free of dirt and grease. Peel back the end of the tape and begin wrapping straight over the leak. Stretch the tape as you wind it on and overlap each turn, extending past the damaged spot on both sides. Press the finished wrap firmly so the layers fuse into one continuous seal. To fit a tool grip, wrap the tape around the handle in the same way. Cut the tape to length with scissors or a knife.Important notesBoston positions this tape for emergency and quick repairs. If a pipe or hose is badly damaged, plan to replace the affected section. Because the tape fuses only to itself, it will not stick to a surface if simply laid flat, so always wrap it back over itself. Keep the unused roll in a cool, dry place out of direct sun. Please follow the instructions that come with the pack.Specifications Brand Boston Product Silicone Self-Fusing Tape Pack 1 roll, 3m length Colour Black Material Silicone Application Hand wrapped, fuses to itself (no adhesive) Stretch Over 300% Temperature range -55°C to +260°C Use Pipe and hose leak repair, tool grips SafetyAs a general precaution, keep the tape out of reach of small children. Do not rely on it as a permanent fix for pressurised or safety-critical plumbing. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Selleys Autofix Instant Gasket High Temperature Sealant is a red, 100% silicone gasket maker for engine and exhaust jobs where ordinary gasket sealants would give up, supplied here as a 100ml squeeze tube. It lets you form a custom gasket straight from the tube on almost any flange, and it is built to cope with intermittent heat spikes up to 343°C.About the formulaAn acetoxy (acetic cure) silicone that cures to a tough, flexible red rubber seal. It flows into uneven surfaces and small gaps between mating parts to make a high-pressure seal, and it is described by Selleys as sensor safe and suited to high torque and vibration use. Continuous service temperature is rated from -40°C to 260°C, with intermittent exposure up to 343°C.Where to use itIndoors: gaskets and flanges in dishwashers, refrigerators, oven doors, plumbing, and heating and air conditioning equipment.Outdoors and under the bonnet: oil pans, valve covers, water pumps, exhaust manifolds, mufflers, tail pipes and exhaust pipe connectors.Intended for metal flanges and similar mating parts in engines, exhausts and appliances. Check the part and the service conditions suit a silicone seal before you start.How to use it Remove all old gasket material, then clean the surfaces with mineral turpentine and let them dry. If you do not want the gasket to adhere (for easier disassembly), wipe the mating surfaces with an oily cloth instead. Take off the cap, remove the foil seal, refit the nozzle and cut it at a 45° angle. Squeeze the tube with steady pressure to lay a bead about 1.5 to 3mm thick on one of the surfaces, running around the bolt holes. Join the parts within 10 minutes. Hand-tighten the bolts until sealant just starts to squeeze out, then leave for 30 minutes. Tighten the bolts to the required torque. If you need a thicker gasket, assemble the parts but leave the bolts loose for 24 hours. Allow 90 minutes before filling with liquid. The sealant fully cures in about 24 hours. Clean up uncured sealant with mineral turpentine. Cured sealant has to be cut and scraped away. Replace the cap after use. Let the sealant cure in the nozzle and pull it out before the next use. Important notesApply in conditions between -20°C and 50°C. A skin forms in about 5 minutes, so work promptly and assemble within 10 minutes of applying the bead. Where a cork gasket is being replaced, make sure parts such as rocker covers still have enough clearance and do not fully tighten until the sealant has cured. If you need to separate the flanges later, pry them apart and clear off the old sealant before reassembling. Store below 30°C and use within 24 months of the production date.Specifications Brand Selleys Product Autofix Instant Gasket High Temperature Sealant Size 100ml tube Colour Red Base 100% acetoxy silicone Application Squeeze tube with cut nozzle Skin time About 5 minutes Set time About 30 minutes Full cure About 24 hours Service temperature -40°C to 260°C Intermittent temperature Up to 343°C Application temperature -20°C to 50°C Density 1.02 g/ml Movement capability 25% Hardness (Shore A) 18 or higher Use Interior and exterior SafetyAvoid skin and eye contact, work in a well-ventilated area and wear suitable gloves and eye protection. Store in a cool, dry, well-ventilated place out of direct sunlight, away from foodstuffs and incompatible materials. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Kinetic Heavy Duty Thread Seal Tape is a pink PTFE plumber's tape for sealing threaded pipe and fitting connections, supplied here as a handy pack of five 12mm x 10m rolls. It gives a clean, positive seal on screwed joints and helps stop leaks at plumbing and heating connections, with a wide working temperature range for hot and cold duty.About the formulaThis is a PTFE (polytetrafluoroethylene) film tape in a heavy duty grade, coloured pink for easy identification on the job. PTFE is naturally corrosion resistant, so the tape will not rust or degrade the way some paste-type sealants can. It is rated for a working temperature of -100°C to 250°C. The tape is not an adhesive: it works by filling the small gaps between mating threads as the joint is tightened.Where to use itPlumbing: threaded water pipe connections and screwed brass fittings, which is the primary application listed for this pack.Heating: threaded joints in heating pipework and similar screwed connections.Suitable pipe and fitting materials include plastic, brass, copper, aluminium, galvanised steel and iron.How to use itMake sure the threads are clean and free of oil, dust and old sealant. Wrap the tape onto the male thread in the same direction the thread turns, so the tape does not unwind when the fitting is tightened. Keep light tension on the tape so it moulds into the thread form. Use several overlapping wraps (typically about four for small threads, with more for larger sizes), then screw the fitting together and tighten as normal. Test the joint under pressure before putting the system into service.Important notesWrapping against the direction of the thread can cause the tape to bunch up and unwind. Do not over-wrap, as too much tape can make fittings hard to assemble or crack plastic female fittings. Check that the tape is approved for your specific application, such as potable water or gas, before use, as approval details for this exact pack are not confirmed here. Keep away from open flames and do not use beyond the stated temperature range.Specifications Brand Kinetic Product Heavy Duty Thread Seal Tape Pack 5 rolls Roll size 12mm wide x 10m long Thickness 0.1mm Colour Pink Material PTFE Working temperature -100°C to 250°C Corrosion resistant Yes Application Hand wrapped onto male threads Packaging Blister pack SafetyAs general precautions, keep out of reach of children, keep away from open flames, store in a cool, dry place and wash hands after handling. Always follow the manufacturer's instructions and local plumbing regulations. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Fix-A-Tap Uniseal High Density PTFE Thread Seal Tape is a grey thread seal tape for gas and water pipe connections, supplied as a single 12mm x 10m roll on a card. The metallic grey pigment helps it blend in with chrome and galvanised fittings, so it is a good choice when you don't want white tape showing at the joint.About the formulaThis is a high density PTFE tape designed to form a leak-proof seal on suitable metal threads. It carries both AGA approval for gas threads and WaterMark approval for water threads. The AGA temperature range is -10°C to +210°C and the rated working pressure is 2MPa.Where to use itIndoors: threaded joints on water and gas pipework, such as fittings, connectors and valves, where a discreet grey finish is preferred.Outdoors: the manufacturer does not give specific outdoor guidance, so check the fitting and installation requirements for your job.It is intended for suitable metal pipe threads on gas and water lines. Always confirm that the tape suits the fitting and the service you are sealing.How to use itMake sure the male thread is clean, dry and free of old tape, oil and debris. Start at the thread end and wrap the tape around the thread in the direction the fitting will be tightened, so it doesn't unravel as you screw the joint together. Keep the tape snug and press it into the thread form, then assemble the joint. Gas fitting must be carried out by a licensed gas fitter in line with local regulations.Important notesUse only within the AGA temperature range of -10°C to +210°C and the rated working pressure of 2MPa. This tape is for threaded metal connections and is not a substitute for a compression, flange or push-fit seal. If a joint still weeps after assembly, dismantle it, remove the old tape and rewrap with fresh tape rather than adding more on top.Specifications Brand Fix-A-Tap Product Uniseal High Density PTFE Thread Seal Tape Size 12mm wide x 10m long Pack 1 roll on card Colour Metallic grey Material PTFE Application Hand wrapped onto pipe threads Temperature range (AGA) -10°C to +210°C Rated working pressure 2MPa Approvals AGA and WaterMark Manufacturer model number 208637 Use Gas and water pipe threads SafetyAs general good practice, keep the tape away from heat and flame beyond its rated temperature range, avoid overheating PTFE, and keep it out of reach of children. Wash your hands after handling if working in a dusty or dirty environment. Always follow the manufacturer's instructions and local plumbing and gas regulations. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Rust-Oleum LeakSeal Self-Fusing Silicone Tape is a no-adhesive repair tape for stopping leaks on pipes and hoses and for wrapping damaged wiring insulation, supplied here as a clear 25.4mm x 3.04m roll. It stretches and wraps around awkward shapes, then fuses to itself to form a tight, water-resistant seal that suits quick home fixes as well as automotive and workshop repairs.About the formulaThis is a silicone rubber tape that bonds to itself rather than to the surface underneath. That is why it peels away cleanly later without leaving a sticky residue. The manufacturer rates it excellent for moisture resistance, electrical insulation, UV and ozone resistance and corrosion prevention, and good for flame, abrasion, tear and solvent resistance. It is also rated good to fair for acid and oil resistance. It meets UL 510 and is claimed to insulate up to 8,000 volts.Where to use itIndoors: weeping or leaking pipes and joints, hoses on appliances, and frayed or worn cable insulation (see the electrical safety note below).Outdoors: garden and irrigation hoses, exposed pipework, and vehicle or equipment hoses and fittings exposed to sun and weather.Suited to wrapping around pipes, hoses, fittings and cables made from common materials such as metal and rubber. As the tape fuses to itself rather than relying on adhesion, it conforms to irregular shapes well. Test a small area first on delicate surfaces.How to use itDry the area to be repaired first. Hold the end of the tape firmly on the problem spot, then stretch the tape under tension as you wrap it around the object. Overlap each layer by about 13mm and keep wrapping so the tape lies over itself and fuses. Cover the whole problem area, cut the tape when finished and press the end down firmly. To remove it, simply unwrap or cut it off.Important notesThe tape needs to be stretched while wrapping, with each turn overlapping the last, to fuse properly. Loose or single-layer wraps will not seal. Treat it as an effective repair or emergency fix, and replace damaged pipes, hoses or cables where a permanent solution is needed. The manufacturer lists continuous operating temperatures from -45°C to 200°C and intermittent exposure from -65°C to 260°C, so keep it away from conditions above these limits. Do not rely on it to repair mains-voltage wiring: isolate the power first and have electrical work carried out by a licensed electrician. Avoid contact with strong oxidising agents, strong acids and strong alkalis.Specifications Brand Rust-Oleum Product LeakSeal Self-Fusing Silicone Tape Size 25.4mm x 3.04m roll (1 roll) Colour Clear Material Self-fusing silicone rubber tape Application Hand wrapped under tension, no adhesive or tools Continuous operating temperature -45°C to 200°C Intermittent operating temperature -65°C to 260°C Tensile strength 700 psi minimum Elongation 300% minimum Hardness Shore A 55 (+/- 5) after 24 hours Electrical insulation Up to 8,000 volts (manufacturer claim) Standard Meets UL 510 Use Interior and exterior SafetyWash your hands thoroughly with soap and water before eating, drinking or smoking after handling. If it gets in the eyes, rinse with water and remove contact lenses if present and easy to do. If heated to decomposition, silicone can give off acrid smoke and irritating fumes, so avoid excess heat and ensure good ventilation. Store the roll in a cool, dry place away from strong oxidisers, acids and alkalis. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Rust-Oleum LeakSeal Self-Fusing Silicone Tape is a stretch-and-wrap repair tape for stopping leaks on pipes and hoses and for insulating damaged electrical wires, supplied here as a single black 25.4mm x 3.04m roll. It has no adhesive layer. Instead, each wrap fuses to the layer beneath it, so it forms a tight, sealed sleeve around the repair and can be cut off later without leaving sticky residue behind.About the formulaThis is a silicone rubber tape that bonds to itself rather than to the surface underneath. Rust-Oleum describes it as a moisture and chemical resistant barrier that also helps protect against corrosion. Its technical data sheet rates it Excellent for moisture resistance, electrical insulation, UV and ozone resistance and corrosion prevention. It rates solvent, abrasion and tear resistance as Good. Acid, oil and hydrocarbon resistance is rated Good to Fair. The tape has a minimum tensile strength of 700 psi, a minimum elongation of 300% and a Shore A hardness of 55 (plus or minus 5) once cured for 24 hours. It meets UL 510. Rust-Oleum states it insulates up to 8,000 volts.Where to use itIndoors: temporary or emergency repairs on leaking pipes, fittings and hoses, and insulating or protecting frayed electrical wires and cable joins.Outdoors: wrapping hoses, fittings and exposed connections that face moisture and sunlight, including automotive and general workshop repairs.Because it fuses to itself, it works best on pipes, hoses, cables and other tubular or irregular shapes that you can wrap fully around.How to use itDry the surface before you start. Press the end of the tape onto the problem area, hold it firmly, then stretch the tape with tension as you wrap it around the object. Overlap each layer by about 13mm (the manufacturer gives 1.2 to 1.4cm) and wrap the tape over itself so it fuses. Cover the whole problem area, cut the tape and press the end firmly into place. To remove, cut the tape carefully with scissors or a knife.Important notesThe tape fuses to itself, so wrap it all the way around the item with each layer overlapping the last. The 700 psi figure on the TDS is a tensile strength rating, so do not treat it as a working pressure rating for pipes. Keep pressurised, hot or critical repairs in line with the system's own requirements and replace them with a proper repair where needed. The TDS gives a continuous operating range of -45°C to 200°C and an intermittent range of -65°C to 260°C. Flame resistance is rated Good, so do not treat the tape as fireproof. For electrical repairs, make sure the circuit is isolated and have any permanent work done by a licensed electrician.Specifications Brand Rust-Oleum Product LeakSeal Self-Fusing Silicone Tape Model number 279241 Size 25.4mm wide x 3.04m long roll (single roll) Colour Black Base Self-fusing silicone rubber Application Hand applied, stretch and wrap Continuous operating temperature -45°C to 200°C Intermittent operating temperature -65°C to 260°C Tensile strength 700 psi minimum Elongation 300% minimum Hardness Shore A 55 (plus or minus 5), cured 24 hours Electrical insulation Up to 8,000 volts (manufacturer rating) Standard Meets UL 510 Use Interior and exterior SafetyIf it gets in your eyes, flush with plenty of water for at least 15 minutes, keep the eyelids open, remove contact lenses if easy to do and keep rinsing. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Gardner Bender Black Self-Bonding Repair Tape is a silicone emergency repair tape for quick, tidy fixes around the home, workshop and vehicle, supplied as a 2.5cm x 3m roll. It has no sticky adhesive layer. Instead, you stretch it as you wrap and it fuses to itself, forming an airtight, watertight seal that suits hoses, pipes, cables and tool handles.About the formulaThe tape is made from silicone and relies on self-bonding rather than glue. It only fuses to itself, so it doesn't leave a tacky residue on the item you wrap. The manufacturer describes it as resistant to heat, friction and UV, and it is rated for temperatures up to 260°C. That makes it handy for jobs where ordinary tapes would soften or perish.Where to use itIndoors: temporary repairs to leaking water pipes, wrapping and protecting electrical cables and connectors, and rebuilding or gripping tool handles.Outdoors and in the vehicle: patching engine hoses and radiator pipes, wrapping exhausts, and emergency repairs on guttering.It is well suited to hoses, pipes, cables, connectors, guttering and similar round or irregular shapes that can be wrapped. Because it bonds to itself rather than to the surface, it works on a wide range of materials.How to use itWipe the area to be repaired so it is clean and dry. For a leak, ideally shut off the flow or pressure first. Start wrapping a short distance beyond each side of the damage. Stretch the tape firmly as you wrap, overlapping each turn by about half the width so the layers press together and fuse. Finish by wrapping the end back onto itself and pressing it down firmly.Important notesThe tape must be stretched while wrapping, otherwise it won't fuse properly. It bonds to itself only, so it is a repair tool and not an adhesive for sticking two different surfaces together. It is an emergency and temporary repair for many plumbing and automotive jobs. Replace damaged pipes, hoses or fittings properly as soon as practical, particularly for high-pressure, gas, fuel or mains-voltage applications. Check the tape's suitability yourself before using it as electrical insulation on live circuits, and always isolate power first. Keep it below the rated temperature of 260°C.Specifications Brand Gardner Bender Product Self-Bonding Repair Tape Size 2.5cm x 3m roll Colour Black Material Silicone Adhesive None, bonds to itself Moisture sealing Yes (waterproof and airtight when wrapped) Maximum temperature Up to 260°C Resistance Heat, friction and UV Application Hand wrapped SafetyAs a general precaution, keep the tape away from children, wear gloves when working around hot pipes or exhausts, and allow hot surfaces to cool before wrapping. Isolate electrical power before working on cables or connectors. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Scandia Wood Heater Fittings Gasket Adhesive & Sealant is a high-temperature paste made for fixing fibreglass rope seals and gaskets on wood heaters, stoves and fireplaces, supplied in a handy 75g tube. It helps rope seals stay put around door edges and flue joins while you work, then holds them in place once it has dried. This makes it a practical choice for replacing worn seals during heater maintenance.About the formulaA thick, cream to white paste with a firm body that stays where you put it, even on vertical surfaces. The manufacturer rates it for temperatures up to 1100°C, which suits the heat inside a solid fuel appliance. The tube comes with a nozzle that you can cut to suit the width of the seal or gasket you are fitting, so you can lay down a neat, controlled line of adhesive.Where to use itIndoors: fibreglass rope seals on heater and stove doors, flue joins, and other gaskets or glass seals on wood-burning heaters, stoves and fireplaces.Outdoors: the brand also lists wood-burning BBQs among its intended uses.Designed mainly for bonding fibreglass rope seals to the metal and masonry parts of a solid fuel appliance. If you plan to use it on another material, check suitability first with a small test.How to use itMake sure the surface is clean, dry and free of soot, loose debris, oil and old adhesive. Cut the tip of the nozzle to suit the seal you are fitting. Apply a line of paste to the channel or edge where the seal will sit, then press the rope seal or gasket firmly into place. Wipe away any excess before it dries.Important notesAllow the adhesive to dry overnight after application before lighting the appliance. Always follow your heater manufacturer's instructions for the correct seal size and fitting method. Always check the seal is fully seated and the door closes properly after fitting. Some users have found the paste firm to squeeze from the tube, so cutting the nozzle a little wider and applying steady pressure can help.Specifications Brand Scandia Product Wood Heater Fittings Gasket Adhesive & Sealant Size 75g tube Colour Cream to white paste Form Thick paste Application Squeeze tube with cut-to-size nozzle Temperature rating Up to 1100°C Drying time Overnight Use Wood heaters, stoves, fireplaces and wood-burning BBQs SafetyIt advises avoiding heat, flames and sparks during storage and handling, and providing good ventilation or respiratory protection against decomposition products. As a sensible precaution, wear gloves and eye protection, and wash off any skin contact with water. Store in a cool, dry place with the cap closed tightly. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less