Dunlop Ready-to-Go Coloured Grout is a premium, pre-mixed grout for fast, clean results on walls and floors. No mixing, no mess, just open, apply, and buff for a smooth, long-lasting finish. The formula includes Grout Shield for anti-mould and anti-bacterial protection to help surfaces stay cleaner for longer. Suitable for interior and exterior applications, and available in a wide colour range to match or contrast your tiles. Ready-mixed convenience, apply straight from the tub Contains Grout Shield for mould and bacteria resistance Use on walls & floors, indoors & outdoors* Ideal for joint widths from 1–5 mm Great for rejuvenating old grout (min. removal depth: 1 mm walls, 2 mm floors) *Always follow the data sheet guidance for your specific area and exposure. Where to Use Ceramic, porcelain and most glazed tiles Bathrooms, kitchens, splashbacks, laundries, living areas Light-duty exterior tiled areas (check exposure & substrate) This grout is designed for typical domestic and light commercial tiling where a smooth, uniform finish is desired. Colours & Finish Available in a contemporary colour palette (e.g. whites and greys) to complement most tile styles. Use Dunlop’s colour selector to visualise combinations before you start. Coverage Coverage varies by tile size, joint width and depth. As a guide (per kg) of grout: Tile size (L×W×Thickness) Joint width 1.5 mm Joint width 3 mm Joint width 5 mm 25×25×4 mm mosaics ≈1.04 m²/kg ≈0.52 m²/kg ≈0.31 m²/kg 100×100×8 mm ≈2.08 m²/kg ≈1.04 m²/kg ≈0.63 m²/kg 200×200×8 mm ≈4.17 m²/kg ≈2.08 m²/kg ≈1.25 m²/kg Tip: Allow an extra 10–15% for wastage due to technique, tile type and site conditions. Directions (Summary) Prep: Ensure joints are clean, dry, and free from dust, adhesive residue and contaminants. For rejuvenation, remove at least 1 mm (walls) or 2 mm (floors) of old grout. Apply: Using a rubber grout float, force grout firmly into joints at a 45° angle. Strike & shape: Allow grout to firm in the joint (~15 mins). Shape joints as required. Clean: Wipe diagonally with a dense, damp sponge, rinsing frequently. Use minimal water to reduce shade variation and shrinkage. Buff: When touch-dry (typically 6–24 hrs), buff tile faces with a clean, dry cloth. Drying & Use Initial set at ~24 hrs at 23 °C / 50% RH Shower walls can be exposed to water after ~24 hrs Clean-Up & Storage Clean tools and residue with water while the grout is still wet. Reseal the tub between uses to prevent skinning. Store upright in a cool, dry place. Safety Read the Safety Data Sheet before use and follow PPE guidance. Avoid contact with eyes and prolonged skin contact. Keep out of reach of children.
$20.15 - $20.18$0.03/g
Agnews Water Putty - Hard-Setting Filler for Wood, Plasterboard, Concrete & More Agnews Water Putty is a professional, powder-based repair and levelling compound for durable, long-lasting results. Mix only what you need with clean water, then patch, level or rebuild surfaces with confidence. Once cured, it sets rock hard, bonds permanently, and can be sawn, drilled and sanded to a smooth, paint-ready finish. Key features Brand: Agnews Unlimited shelf life when stored dry Non cracking, non shrinking, non sinking Won't fall out – adheres firmly and fills to any depth Interior & exterior grade (seal exterior applications after full dry) Non flammable and no VOCs Mix what you need for minimal waste Suitable substrates Plasterboard, concrete, wood/timber, cement sheet, masonry. Also suitable for minor floor levelling and feathering on concrete, timber and ceramic tile substrates. Typical applications Fill holes in wood: knotholes, nail and screw holes, dents, edge build-ups Wall patching: cracks and cavities in plasterboard and cement sheet Furniture repair: tighten loose joints, reset fasteners, rebuild profiles Floor levelling: ramp or smooth minor level variations before floor coverings Trim and fixtures: refit loose door bumpers and trims with reliable hold Architectural & hobby moulding: casting and shaping durable components Why choose Agnews Agnews Water Putty cures to a dense, stone-hard finish that resists shrinkage and cracking even in deep fills. It bonds securely, stays put, and finishes cleanly, delivering a stable base for sanding, priming and painting. From small touch-ups to larger restorations, it provides consistent, professional results. Directions (general guide) Surface prep: Ensure the area is clean, dry, sound and free of dust, oil or loose material. For very porous substrates, lightly dampen to reduce rapid suction. Mix: Add powder to clean water and blend to a smooth, lump-free paste. Adjust water to suit application (thicker for filling, looser for fairing/skim). Apply: Press firmly into cracks or voids with a putty knife or trowel. Overfill slightly so you can sand back flush. Cure: Allow to dry thoroughly. Dry time varies with thickness, temperature and humidity. Finish: Sand to profile. Prime and paint or seal. For exterior applications, always seal after full dry. Exterior use guidance This is a hard-setting, non-flexible compound. For exterior use, only apply over stable substrates with minimal expansion and contraction from temperature changes. Ensure the putty is fully dry before sealing with a suitable exterior-grade coating. Finishing & compatibility Paintable and sealable after full dry; prime as required for best results. Can be cut, carved, drilled and sanded after cure without crumbling. For stained timber finishes, test a small area first for colour and absorption. Pro tips Mix small batches and use promptly. For deep voids, apply in layers if needed, allowing each layer to firm before the next. Store powder in a cool, dry place to maintain its unlimited shelf life. Clean tools with water before material cures. At a glance Substrates: plasterboard, concrete, wood/timber, cement sheet, masonry Uses: patching, levelling, rebuilding, moulding Properties: non cracking, non shrinking, non sinking, non flammable, no VOCs Finish: hard, dense, smooth and paint-ready after sanding/priming
$8.77 - $86.00
Dunlop Flexible Coloured Grout is a smooth-finish, flexible cement-based grout available in a wide palette of popular colours to complement almost any tile. Its stronger colour formula gives rich, consistent joints, while built-in Grout Shield anti-mould and anti-bacteria technology resists mould and bacteria growth to keep wet areas looking fresher for longer. Easy to work and forgiving to clean off, it ensures flush joints with no pin holes.Where to use itUse it on walls and floors, indoors and outdoors, with ceramic, porcelain, marble, granite and mosaic tiles. It handles joints from 1mm right up to 8mm, so one product covers both fine wall joints and wider floor joints. For swimming pools, use the White 200 colour mixed with Dunlop Primer & Additive.How to useMake sure joints are clean, dry and raked clear of adhesive. Mix the powder with clean water (or with Dunlop Primer & Additive for extra flexibility, adhesion and stain resistance) to a smooth paste. Spread diagonally across the tiles with a rubber float, packing joints full, then sponge the surface clean once firm and buff off the haze. Initial set occurs after about 24 hours; showers can be exposed to water after 3 days, the grout can be sealed after 3 days and full cure is reached in 7 days.Important notesCoverage depends on tile size, joint width and depth - allow around 15% wastage. Colour can vary slightly with water content and curing conditions, so mix consistently between batches.Specifications Joint width 1 - 8mm Coverage guide Approx. 0.55kg/m² for 200 x 200 x 8mm tiles at 3mm joints Tile types Ceramic, porcelain, marble, granite, mosaics Location Walls and floors, indoor and outdoor SafetyCement-based - the wet mix is alkaline and may irritate skin and eyes. Wear gloves and eye protection, avoid breathing mixing dust, and wash after use. Keep out of reach of children; refer to the Safety Data Sheet.
$13.88 - $15.24
This versatile adhesive is specially formulated for fixing most tile types, offering excellent flexibility and suitability for various surfaces. Key Features: Suitable for most tile types Can be applied over a variety of surfaces Suitable for interior timber (with proper preparation) Highly flexible Tile Types: Ceramic tiles Fully vitrified tiles Mosaics Porcelain tiles Natural stone (excluding moisture-sensitive stone) Suitable Surfaces: Cement render and concrete Fibre-cement sheets Existing ceramic and vinyl tiles Dunlop Undertile Waterproofing Metal surfaces Oil-based painted surfaces Plasterboard Indoor timber (must be adequately prepared) Application Areas: Walls and floors Indoor and outdoor use (as long as there’s no standing water and proper water run-off is ensured) Coverage: Tile Size Trowel Size Coverage Up to 250 x 250mm 6-8mm 0.8m²/kg 250 x 250mm and larger 10-12mm 0.5m²/kg
$39.01
Concremate Expanding Anchoring Cement Anchor, patch and lock in place with confidence. Concremate is a high-performance expanding cement designed for rapid, reliable anchoring and structural patching. Mixed to a workable, mortar-like consistency, it expands slightly as it cures to counteract drying shrinkage. That controlled expansion grips embedded items and surrounding material tightly, delivering a secure, long-lasting hold that stands up to strain, stress and vibration. Why choose Concremate Fast turnaround: initial set in about 30 minutes and hard in approximately 1 hour, so many jobs can progress the same day. Expands and grips: engineered expansion of about 0.125% offsets shrinkage and locks into the substrate. High ultimate strength: cures to a finish that becomes harder than standard concrete at 28 days when properly mixed and applied. Versatile application: ideal for anchoring bolts, rails, brackets and fixtures, as well as patching holes, chases and cracks. Durable performance: forms a robust, long-term bond that resists severe mechanical stress and vibration. Where it excels Use Concremate for secure embedment and structural repairs on common mineral surfaces. It is suitable for: Concrete and masonry Brickwork and stone Tiles and terrazzo Plaster and similar mineral substrates Typical projects Anchoring handrails, posts, machine base bolts, threaded rods and heavy brackets Fixing door and window hardware to masonry openings High-pressure grouting under plates, around pipe sleeves and service penetrations Patching voids, chased conduits, spalled edges and impact damage in floors, walls and ceilings How it works Concremate is a mineral-based expanding cement. After mixing with clean water, the paste hydrates and begins to set. A small, controlled expansion during cure offsets natural drying shrinkage. The result is a tight, interference-style fit that increases grip on embedded items and keys the patch into surrounding material. For best results, the material must be able to expand slightly while drying and should not be constrained in a completely sealed cavity. Directions for use Surface preparation: Remove dust, loose material, laitance, oil and contaminants. Roughen smooth surfaces and blow or brush clean. Pre-dampen porous substrates to a surface-saturated dry condition; do not leave standing water. Mixing: Add powder to clean water while stirring until a smooth, lump-free, mortar-like consistency is reached. Mix only what you can place within the working time. Do not over-water. Placement for anchoring: Fill the prepared hole or pocket from the bottom up to avoid entrapped air. Insert the fixture or fastener while the mix is workable and align immediately. Hold steady until initial set. Placement for patching: Tightly pack the mix into the void in layers, compacting each layer to ensure full contact. Strike off and finish the surface as required. Curing: Protect from rapid drying, wind and direct sun during early cure. Avoid vibration or load until the material has hardened. Cleanup: Clean tools and splashes with water while product is fresh. Once hardened, mechanical removal may be required. Good practice tips Plan the job so placement occurs immediately after mixing for best expansion and bond. For deep holes or large voids, place in lifts and compact each lift. Do not confine completely in a sealed cavity; allow space for controlled expansion. Avoid adding sand, cement or other admixtures that can change performance. Performance and durability When correctly mixed and applied, Concremate develops a hard, dense matrix with strong adhesion to mineral substrates and embedded metals. The slight expansion on cure reduces micro-gapping at the interface, improving load transfer and long-term durability. After full cure at 28 days, the set material achieves hardness that exceeds standard concrete, supporting demanding anchoring and patching tasks. Safety and handling Wear suitable gloves, eye protection and a dust mask when mixing and placing. Avoid contact with skin and eyes. In case of contact, rinse with plenty of water. Store in a cool, dry place in the original, tightly closed container. Keep out of reach of children and pets. Specifications Product type Expanding cement anchoring and patching compound Form Premixed dry powder Color Grey Mix consistency Mortar-like paste when mixed with clean water Initial set About 30 minutes (conditions dependent) Hard set Approximately 1 hour (conditions dependent) Ultimate hardness Harder than standard concrete at 28 days Expansion Approx. 0.125% during cure Recommended substrates Concrete, brick, stone, tiles, plaster, terrazzo Primary uses Anchoring bolts, rails, brackets and fixtures; patching holes, chases and cracks; high-pressure grouting Cleanup Water while fresh Storage Cool, dry conditions in sealed container What to expect on the job With suitable surface preparation and correct mixing, you can expect a smooth placement, quick set and a dense, high-integrity bond. The expansion action helps lock hardware and patches into place. Protect new work from early movement and moisture loss, then return to service once the hard set has been achieved and the repair or anchorage has reached the necessary strength for your application. Limitations Not for use where the mix cannot expand slightly during cure. Do not apply over active movement joints or flexible substrates. Working and set times vary with temperature, humidity and mix ratio. Note: Always trial on a small, inconspicuous area or non-critical hole to confirm suitability for your specific substrate and conditions.
$17.95 - $115.00
Casting, modelling, moulding, sculpting, carving. Fine quality to hold detail. Sands smooth.
$8.78
Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS Initial set 5 minutes. Curing set 15-30 minutes. Compressive strength of 2,000psi or greater in 24 hours Maximum strength in 28 days Non-toxic Volume change: Expansion after 24 hours 0.1% Contraction after 28 days 0.01% Water absorption 1.7% after 14 days Factory Production to BS 5750 Part II BONDS TO: CEMENT TIMBER MASONRY FIBREGLASS STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.
$25.95
Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS Initial set 5 minutes. Curing set 15-30 minutes. Compressive strength of 2,000psi or greater in 24 hours Maximum strength in 28 days Non-toxic Volume change: Expansion after 24 hours 0.1% Contraction after 28 days 0.01% Water absorption 1.7% after 14 days Factory Production to BS 5750 Part II BONDS TO: CEMENT TIMBER MASONRY FIBREGLASS STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.
$165.00
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications. Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried. Environmentally friendly Dries white Dries fast Very high weather resistance Unique properties make this product easy to shape and sand Ideal for schools and craft classes or just having fun!
$9.35
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications. Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried. Environmentally friendly Dries white Dries fast Very high weather resistance Unique properties make this product easy to shape and sand Ideal for schools and craft classes or just having fun!
$39.15
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$33.95
A vinyl reinforced cement-based filler that is water and weather resistant. Matches cement grey when set and easily sands whilst maintaining the strength of cement. Can be nailed and screwed without splitting or breaking. Will not shrink when used in accordance with directions, making it suitable for use in patching steps, paths, paving etc. For use on: Bricks, cement, stone and other masonry surfaces (EXTERIOR). May be used in interior wet areas and as ceramic floor tile cement. Fill depth: Dependent on mix ratio Dries in: 5-6 hours for sanding. Allow 24 hours before painting. Ready to use: NO (mix with water) Available in: 500g & 2kg Colour: Grey and can be tinted by adding cement colorants to the mixing water. Application tips: • Surface to be filled should be clean and dry with no loose or powdery material. Do not wet or prime surfaces before filling. • Coat nail heads with oil based paint prior to filling to prevent rust staining. • Add 4 parts Polyfilla Exterior Powder Filler to 1 part water in a clean container and mix thoroughly into a smooth paste. Use mix within 30 minutes and do not add water to extend working time. • For deeper cracks and holes and on very absorbent surfaces it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Press in the mixed filler with a filling knife or trowel and finish with a slightly rounded surface. Where a smooth surface is required, slightly overfill the surface, allow to dry (approx. 5-6 hours), then sand smooth with medium grade sandpaper. • Leave for 24 hours, and then apply a suitable primer/undercoat before painting. • When applying in thin layers, do not over trowel. • Clean up with water before filler dries
$21.60
Dunlop Ardit Rapidset Repair Mortar is an extremely fast-hardening construction mortar from Dunlop Trade (ARDEX Australia), formulated for patching cracks, holes and damaged sections with minimal downtime. Repairs can take foot traffic after just 45 minutes and accept floor coverings after 1 hour, so a morning patch job doesn't hold up the rest of the day's work.Where to use itSuitable for indoor and outdoor repairs on concrete, render, screeds, masonry, plasterboard, timber and fibre-cement sheet. It is handy for patching floors before coverings, forming small ramps, and tidying up around doors, windows and plumbing penetrations internally.How to useClean out the damaged area so it is sound and dust free. Mix the powder with clean water (approximately 1.5L per 5kg) to a smooth, workable consistency and apply firmly with a trowel, compacting into the repair. It can be worked from a feather edge up to 20mm thick and shaped before it stiffens. Work in small batches, as the working time is around 15 minutes.Important notesOnly mix what you can place within the working time. Deeper repairs can be built up in stages. Backed by a 10 year guarantee when used as directed - see the technical datasheet for full details.Specifications Size 5kg bag Coverage Varies with patch depth; feather edge to any thickness Thickness Feather edge up to 20mm per application Substrates Concrete, render, screeds, masonry, plasterboard, timber, fibre-cement Walk-on time 45 minutes (floor coverings after 1 hour) SafetyCement-based powder - wear gloves, safety glasses and a P2 dust mask when mixing, keep the area ventilated and avoid prolonged skin contact with the wet mortar. Wash hands after use and keep away from children.
$32.71
Davco Ceramacrete Cement Base Tile Adhesive 5kg Davco Ceramacrete is a cement based tile adhesive for rigid substrates with patented Dust Less technology that reduces airborne dust during mixing. It offers good bond strength, tidy mixing and clean up, and can be used in thin or thick beds for efficient tiling results. Where to Use Interior and exterior walls and floors Bathrooms, showers, kitchens, laundries, living areas, balconies and patios Domestic and light duty commercial projects Tile Types Ceramic Mosaic Terracotta Slate Quarry tiles Not suitable for natural stone. Suitable Substrates Concrete Cement based screeds and renders Rendered block or brickwork For flexible framed substrates or submerged applications such as pools and spas, use with Davco Davelastic additive as directed. Key Features Dust Less formula for less mess and faster clean up Good bond strength Usable for thin bed and thick bed tiling Colour varies from white to grey Low VOC 5 g/L Mixing and Application Mixing ratio 1.25 L of clean cool water per 5 kg bag Allow to stand for 5 minutes after mixing, then remix before use Do not add extra water after initial mixing Working Times at 23°C and 50% RH Pot life 40 minutes Open time 7 minutes Adjustability time 15 minutes Ready for Use Grouting after 24 hours Return to dry area service after 24 hours Return to wet area service after 7 days Preparation Tips Ensure substrates are sound, clean, dry and free from contaminants Prime as required according to substrate condition and primer directions Install movement joints in line with good tiling practice Clean Up and Safety Clean tools with water before the adhesive dries Use appropriate personal protective equipment Refer to the product SDS for detailed safety advice
$10.30
Selleys Spakfilla Heavy Duty is a multi-purpose, tough and durable, light grey ready-mixed filler. Features Suitable for interior and exterior applications Good adhesions to most surfaces Water and weather resistant Fill cracks and holes in a single application Pre-mixed and ready to use Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water-based, so can be cleaned up with water Paintable with oil and water-based paints Where can this product be used? Filling holes, dents, cracks or chips in interior and exterior applications where no structural movement occurs What materials is this product suitable for? Mortar Masonry Concrete Wood Stone Primed metal surfaces Brick Plaster Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. For deeper cracks, apply in 6mm layers allowing each layer to dry before applying the next. Lightly sand back any excess filler from the surface after product dries (2-3 hours for 2mm applications). Dust off any loose dust before applying undercoat and painting with water-based paints or oil-based paints. Limitations: Product is not flexible so not suitable for use between surfaces that are subject to the structural movement - use Selleys No More Gaps. Avoid using below 5°C or in wet conditions. Painting with oil-based paints is not recommended until 24 hours after the filler has been applied. Water-based paints may be used immediately after the filler has set. If the filler is found to have stiffened prior to use, stir product. The product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency. Application tools may be cleaned with water. Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen. In exterior applications, protect from rain until dry and painted over with 2 coats of paint. Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry. For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times. Keep container closed when not in use.
$22.66
Features Resists intense heat Sets hard Water clean up Where can this product be used? Repairing bricks in fireplaces and chimneys Sealing flues in pot-belly stoves Filling cracks in ironworks and bricks What materials is this product suitable for? Brick Metal Concrete How to Use: Remove all dust, grease and loose debris before applying material. Dampen the cavities on porous surfaces for better adhesion. Apply Fireproof Cement firmly into holes and cracks with a damp knife or spatula. Allow Fireproof Cement to dry a minimum of 48 hours before exposure to heat. If Fireproof Cement is stiff slacken with a little water. Limitations: Fireproof Cement is not an adhesive - it is a filling compound. Not recommended for external use e.g. BBQ's, incinerators etc. Fireproof Cement is not suitable for use in kilns. Fireproof Cement is not recommended for moving joints such as expansion joints as it sets rigidly Hardened material cannot be resoftened with water.
$48.00
Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS Initial set 5 minutes. Curing set 15-30 minutes. Compressive strength of 2,000psi or greater in 24 hours Maximum strength in 28 days Non-toxic Volume change: Expansion after 24 hours 0.1% Contraction after 28 days 0.01% Water absorption 1.7% after 14 days Factory Production to BS 5750 Part II BONDS TO: CEMENT TIMBER MASONRY FIBREGLASS STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.
$101.37
Polyfilla Rapid 30 340g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces Quick, Reliable, and Versatile Filler for All Surface Types If speed is of the essence, Polyfilla Rapid 30 340g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces. Key Features: Extremely easy to sand Sets to a hard finish Highly crack-resistant Fills up to 50mm deep holes Dries in as fast as 30 minutes* Suitable for multiple surfaces: plasterboard, brick, timber, and concrete How to Use: Clean and dry the surface, ensuring no loose or powdery material. Press the filler firmly into dents and holes, feathering edges to minimize sanding. Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications. For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat. Limitations & Tips: Use Poly Gap filler where joint movement occurs. Do not fill more than 50mm deep. Clean up with water before the filler dries. For quick paint-over solutions, consider using Poly Quick Dry. *Drying time is based on a 2mm application. With Polyfilla Rapid 30 340g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
$36.88
Polyfilla Rapid 30 140g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces Quick, Reliable, and Versatile Filler for All Surface Types If speed is of the essence, Polyfilla Rapid 30 140g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces. Key Features: Extremely easy to sand Sets to a hard finish Highly crack-resistant Fills up to 50mm deep holes Dries in as fast as 30 minutes* Suitable for multiple surfaces: plasterboard, brick, timber, and concrete How to Use: Clean and dry the surface, ensuring no loose or powdery material. Press the filler firmly into dents and holes, feathering edges to minimize sanding. Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications. For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat. Limitations & Tips: Use Poly Gap filler where joint movement occurs. Do not fill more than 50mm deep. Clean up with water before the filler dries. For quick paint-over solutions, consider using Poly Quick Dry. *Drying time is based on a 2mm application. With Polyfilla Rapid 30 140g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
$21.59
A ready-mixed filler that dries hard to a durable finish for deep and wide cracks in mortar, concrete, cement render and brick. Water, weather, UV, algae and mould resistant Can be tooled to a render texture or sanded to a smooth finish. For use on: Bricks, concrete, bare or painted cement render & other masonry surfaces (EXTERIOR & INTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Available in: 500g and 2.2kg Colour: Cement grey in colour but can be painted over with both oil and water based paints • Ensure surfaces are clean and free from dust, grease, mould/algae and flaking/powdery paint or material. If necessary wash with Poly Sugar Soap. • Rinse thoroughly and allow surface to dry. • Use flexible filling blade to press filler into hole, or trowel to spread a thin layer over surface, and tool to a feathered edge. • Allow to dry (2–3 hours in thin 2–3mm applications, depending on temperature and humidity) before sanding and painting. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather. • For deeper jobs apply in 10mm layers, allowing each layer to dry before applying the rest. • Protect from rain until dry. If required, paint with a quality exterior coating. • For a render texture smooth out with trowel or filling blade when applying the product and do not sand. For a smoother texture sand surface after drying. • For best results, apply undercoat before applying water or oil based top coat. • Where joint movement occurs, use a flexible Poly sealant. • Clean up with water before filler dries.
$22.91
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink. For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR) Fill depth: Dependent on mix ratio Dries in: 2-3 hours Ready to use: NO (mix with water) Available in: 500g, 1kg, 2kg & 6kg Colour: Off-white • Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key. • Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate. • Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge. • Leave for 2-3 hours before sanding and decorating. • For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area. • Clean up with water before filler dries
$46.15
High-Performance Multipurpose Wall & Floor Tile Adhesive This versatile adhesive is designed for fixing almost all tile types to a wide range of challenging surfaces, including water features and swimming pools. Key Features: Suitable for both walls and floors Can be applied over difficult surfaces, including water features Allows tiling over existing tiles Compatible with most types of ceramic and natural stone (excluding moisture-sensitive stone) Tile Types: Ceramic tiles Fully vitrified tiles Natural stone (excluding moisture-sensitive stone) Mosaics Porcelain Suitable Surfaces: Existing tiles Glazed ceramic tiles Metal Roughened fibreglass Timber (particleboard only) Application Areas: Walls and floors Indoor and outdoor Water features and swimming pools Coverage: Tile Size Trowel Size Coverage Up to 250 x 250mm 6-8mm 0.4m²/kg 250 x 250mm and larger 10-12mm 0.25m²/kg
$49.42
Davco Lanko 136 Rapid Patching Mortar is a fast-setting, cement-based repair mortar for patching concrete, brickwork and rendered surfaces, supplied here in a 5kg bag that suits small to medium repairs. It gains strength very quickly, so floor finishes, underlayments and coatings can go over the repair in a fraction of the time that a standard patching mix needs.About the formulaA one-part, pre-blended grey powder made from cement, selected aggregates and special additives. It is polymer modified, so you only add clean water. Davco describes it as shrinkage compensated to help resist cracking as it cures, with a fine, workable finish. It sets rapidly and develops very high early strength, and the manufacturer lists it as freeze/thaw resistant once cured. It is not a vapour barrier.Where to use itIndoors: patching holes, chips and defects in concrete floors before levelling compounds, underlayments, carpet, vinyl or ceramic tiles go down; forming small ramps or transitions before floor coverings; treating chamfers, coves and seams before waterproofing membranes or epoxy coatings.Outdoors: repairing concrete slabs, pillars and posts; patching brickwork and rendered walls before tiling, coating or painting.Suitable materials include concrete, brick, block, masonry and cement render. Always apply it to a sound, properly prepared surface.How to use itRemove dust, loose material, oil, grease and anything else that could stop a bond. Dense, power-floated concrete may need a bonding primer or moisture barrier first, so check the Davco data sheet for the recommended options. Mix with clean potable water only, at about 0.53 to 0.6 litres per 5kg bag. Add the powder to most of the water while mixing, then adjust to a workable consistency with a drill and paddle or by hand. Mix only what you can place within roughly 15 minutes. Press a first pass firmly into the surface with a steel trowel, build up to the required thickness, then finish with a wet steel trowel or foam float. Do not vibrate the mortar into place, and discard any mix that starts to stiffen.Important notesDo not apply in direct sun or strong winds, and keep the air and surface temperature at or above 7°C. Do not feather edge this mortar. It is a repair material and not a wearing surface, so cover it where it will be exposed to wear. The manufacturer's guide is that floor finishes and underlayments can go on after about 90 minutes. Foot traffic is possible in about 45 minutes at 23°C, and epoxy coatings can go on from about 4 hours (do an on-site test first). Deeper or heavy-load repairs need extra care and cure time, so follow the data sheet. Strength figures vary with the aggregates and site conditions.Specifications Brand Davco (Lanko range) Product Lanko 136 Rapid Patching Mortar Pack 5kg bag Colour Grey powder Base Cementitious, polymer modified Application Mixed with water, applied by steel trowel Mixing ratio About 0.53 to 0.6 L water per 5kg bag Yield About 2.5 L per 5kg bag Compressive strength About 13 MPa at 1 hour, about 80 MPa at 28 days (23°C) Ready for floor finishes From about 90 minutes Storage Sealed, dry, between 5°C and 35°C Use Interior and exterior SafetyAvoid breathing dust, and wear gloves, protective clothing and eye or face protection. Remove contaminated clothing and wash it before reuse. If it gets on skin, wash with plenty of water. Store the sealed bag dry and keep it out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$34.72
Dingo Fire Rated Mortar is a ready-to-mix, rapid setting cement mortar made for the high heat areas of pizza ovens, fireplaces and barbeques, supplied here as a 10kg bag. It suits both new builds and patch repairs, so you can use it to build a heat-exposed structure or to fix up an existing one.About the formulaA cement-based dry mix made from high temperature resistant alumina cement and graded aggregates. You only add clean water, and no other components are needed. The manufacturer rates it for heat resistance up to 800°C, referencing AS 1530.1:1994 (R2016). Once mixed, it sets quickly: the initial set takes about 2 hours and the final set about 3 hours.Where to use itIndoors: fireplaces and chimneys, including building them and patching existing masonry.Outdoors: pizza ovens and barbeques, both new construction and repairs to existing structures.It is intended for masonry heat-zone work such as pizza ovens, barbeques, fireplaces and chimneys. For any other material or use, check with the manufacturer first.How to use itLay out your project and have all your tools ready before you open the bag. Make sure surfaces are clean, sound and free from oil, grease and loose particles. Tip the amount you need into a clean bucket, then add clean water gradually. A 10kg bag needs roughly 1.6 to 1.7 litres of water. Mix mechanically for at least 3 minutes, using a low speed electric drill with a paddle mixer, until the mix is thorough and even. Use the contents as soon as you can after opening the pack. A 10kg bag makes roughly 6 to 6.5 litres of mortar.Important notesMix only what you can use within the setting window, as the mortar begins to set after about 2 hours. The bag holds 10kg net of dry product, so take care when lifting it. Poor manual handling can cause injury. Prolonged skin contact with the wet mix may cause irritation, dermatitis or alkaline burns.Specifications Brand Dingo Product Fire Rated Mortar Pack 10kg bag (dry powder) Colour Grey Base Cement based (alumina cement and graded aggregates) Application Mix with water and apply as mortar for new construction or patching Mixing water About 1.6 to 1.7L per 10kg bag Yield About 6 to 6.5L of mortar per 10kg Set time Initial set 2 hours, final set 3 hours Heat resistance Up to 800°C Standard referenced AS 1530.1:1994 (R2016) Use Pizza ovens, fireplaces, barbeques and chimneys SafetyThe wet mix can irritate the eyes and skin, and the manufacturer notes that prolonged exposure may cause dermatitis and alkaline burns. Avoid contact with eyes and skin, and take care when handling the 10kg bag. Refer to the Safety Data Sheet (SDS) for full details.
$44.31
Dingo Fast Set Mortar is a ready-blended, quick-setting mortar for small masonry repairs around the home and on the building site, supplied here in a handy 3kg bag. Just add water to turn the dry mix into a workable mortar for patching, repointing and other quick fix-up jobs, with a set time of around 15 minutes.About the formulaA dry, pre-mixed blend of cement, sand and additives, so there is no need to source and proportion separate materials for a small repair. Dingo describes it as a smooth, buttery mortar, and it cures to a grey finish. The 3kg pack suits small jobs where a full bag of general mortar would be wasted.Where to use itIndoors: small patches and repairs to masonry or brickwork where a quick turnaround matters.Outdoors: repairs to brick and render walls, repointing brickwork, grouting and patching around the home and on building sites.Suitable for brick, block and stone laying and for masonry and render repairs.How to use itLay out your project and have your tools ready before you start, because the mortar sets quickly. Tip the amount you need onto a clean surface or into a wheelbarrow or mixing tub, then add clean water gradually while mixing thoroughly to a stiff consistency. If you add too much water, leave the mix aside until it thickens back to a workable consistency. Trowel the mortar onto your bricks or blocks. Lightly soak clay bricks in water before laying, and lay concrete blocks dry. Mix only what you can use quickly, and use the contents soon after opening the bag.Important notesKeep the mortar damp for about a week after application to help it harden. Retaining walls should not be backfilled for at least two weeks. Keep the dry mix and any unused product dry before use. The amount of water needed is stated differently across published sources, so follow the directions printed on your bag and add water gradually.Specifications Brand Dingo Product Fast Set Mortar Pack 3kg bag Colour Grey Base Cement and sand pre-mix with additives Application Mix with water, apply by trowel Set time About 15 minutes Curing Keep damp for about one week Use Masonry, brick and render repairs, repointing, grouting and patching SafetyAs with all cement products, mixing it may irritate the eyes and skin. Cement dust can irritate the eyes, skin and respiratory system, and prolonged skin contact may lead to dermatitis or alkaline burns. Wear gloves, eye protection and suitable protective clothing, avoid breathing in dust (use a dust mask when needed) and wash skin thoroughly after handling. Store in a dry place. Refer to the Safety Data Sheet (SDS) for full details.
$6.57
SikaGrout Deep Pour is a flowable, precision cementitious grout built for large sections and deep pours of up to 500mm, supplied here as a single 20kg bag. It suits machine bedplates, anchor bolts and other heavy grouting jobs where you need a high-strength, shrinkage-compensated fill that sets quickly and keeps developing strength.About the formulaA ready-mixed grout made from Portland cement, graded aggregates and Sika admixtures. It expands in two stages (Class A and C) to offset the shrinkage normally seen with Portland cement grouts. Sika lists shrinkage compensation, high early and 28-day strengths, good flow, adjustable consistency, good impact and thermal resistance, and no corrosion risk to steel or iron. It is lab tested to AS 1478.2. You mix it with water on site, and the consistency can be adjusted to suit the job.Where to use itIndoors: grouting machine bedplates, anchor bolts and crane rail soleplates in plant rooms, workshops and industrial buildings.Outdoors: mass grouting and concreting, bridge bearing pads and pre-cast concrete sections, with the curing precautions below.Designed for use with concrete and masonry structures, steel baseplates and anchor bolts.How to use itPrepare the substrate and formwork first, and check that the area is within the application temperature range. Mix the 20kg bag with clean water to the ratio on the Sika Product Data Sheet (about 2.5 to 2.8 litres per bag), then adjust within that range to reach the flow you need. Pour from one side of the void so air is pushed out rather than trapped. Place it in layers from 20mm up to 500mm in one pour. For depths over 500mm, Sika recommends adding clean, well-graded aggregate to reduce exothermic heat. Start curing straight away with plastic sheet, wet hessian or a liquid curing membrane to shield the grout from sun and wind. Clean tools and equipment with water while the grout is still wet. Hardened grout can only be removed mechanically.Important notesPot life is about 30 minutes at 20°C, so only mix what you can place in that time. Apply with air and substrate temperatures between 5°C and 35°C. Good curing is vital for final strength and for tight contact with the baseplate. Shelf life is 9 months in undamaged, sealed packaging stored dry and cool. Always follow the current Sika Product Data Sheet for mixing ratios and placement limits.Specifications Brand Sika Product SikaGrout Deep Pour Pack 20kg bag Colour Grey powder Base Portland cement with graded aggregates and admixtures Application Mixed with water and poured Layer thickness 20mm to 500mm per pour Mixing water About 2.5 to 2.8 litres per 20kg bag Yield About 9.8 litres of grout per 20kg bag Pot life About 30 minutes at 20°C Compressive strength About 12 MPa at 1 day and about 70 MPa at 28 days (AS 1478.2, 50mm cubes) Application temperature 5°C to 35°C (air and substrate) Standard Lab tested to AS 1478.2 Shelf life 9 months SafetyIt lists the product as causing skin irritation, causing serious eye damage, possibly causing an allergic skin reaction and possibly causing respiratory irritation. Avoid breathing dust, use in a well-ventilated area and wash skin thoroughly after handling. Wear gloves, eye protection and a suitable dust mask, and keep contaminated work clothing at work. If dust is inhaled, move to fresh air. Refer to the Safety Data Sheet (SDS) for full details.
$71.01
Sikalastic-1K (also labelled Sikalastic-1 Komponent) is a one-component, cement-based waterproofing membrane for wet areas, balconies, tanks and below-ground walls, supplied here in a 10kg pail that suits small to medium jobs. You only add water, then apply it by brush or trowel to form a flexible, crack-bridging, fibre-reinforced coating that protects concrete and prepares surfaces for tiling.About the formulaA fibre-reinforced mortar based on cement modified with alkali-resistant polymers, plus selected aggregates, fine fillers and additives. The consistency can be adjusted with the amount of water, so it can be made thinner for brushing or stiffer for troweling. It has good sag resistance on vertical surfaces, bonds well to concrete, cement mortars, stone and masonry, and can be applied on damp substrates. Sika lists it as meeting AS/NZS 4020 for products in contact with drinking water.Where to use itIndoors: bathrooms, showers and laundries before tiling with a cement-based tile adhesive; flexible protection of concrete tanks, basins and pipes; waterproofing walls and floors in basements against negative water pressure.Outdoors: terraces and balconies before tiling; swimming pools before tiling; external wall surfaces that will be backfilled in ground; protective coating for reinforced concrete exposed to freeze-thaw and carbon dioxide attack.Suitable substrates include concrete, cement mortars, stone and masonry. Substrates must be structurally sound and clean, and all joints and gaps must be sealed before coating.How to use itPrepare the substrate so it is sound and free of dust, oil and loose material, and seal any joints or gaps. Add water to the powder and mix with a low-speed mixer until smooth. For a 10kg pail, Sika's current data sheet gives about 3.0 litres of water for brush application and about 2.2 litres for trowel application. Apply in at least two layers: no more than about 1mm per layer by brush or 2mm per layer by trowel. Sika specifies a total dry film thickness of about 2mm for standard applications and 3 to 4mm for negative-pressure or immersed applications. When brushing, work in two directions, crosswise. Mixed material has a pot life of about 30 minutes at 20°C. Clean tools with water before the material sets; hardened mortar can only be removed mechanically.Important notesApply only when air and substrate temperatures are between 5°C and 35°C. The membrane must be completely hardened before tiling, overcoating or water contact. At 20°C, Sika's guide is about 2 days before tiling, painting with a water-based coating or immersion in water, and longer in cooler conditions (about 3 to 7 days at 10°C depending on the use). Allow about 15 days before contact with drinking water. Tile over it with a polymer-modified, cement-based tile adhesive from the Sika range. Times vary with temperature and humidity. Consumption depends on substrate roughness; as a guide, about 1.2kg per m² per mm of thickness. Store in the original sealed pail in cool, dry conditions and protect from water. Check the production date, as the current Sika data sheet gives a shelf life of 6 months. Always follow the current Sika product data sheet for your application.Specifications Brand Sika Product Sikalastic-1K (Sikalastic-1 Komponent) one-component cementitious waterproofing mortar Pack 10kg pail Colour Light grey Base Cement modified with alkali-resistant polymers, with fibres Application Brush or trowel (mix with water) Pot life About 30 minutes at 20°C Application temperature 5°C to 35°C (air and substrate) Fresh mortar density About 1.5 kg/L Consumption About 1.2 kg/m² per mm (guide) Water contact About 2 days at 20°C before immersion; about 15 days before drinking water contact Approvals AS/NZS 4020 (contact with drinking water) Use Interior and exterior SafetyWet and dry cement products can cause serious eye damage, so wear safety glasses or a face shield, protective gloves and long sleeves, and avoid breathing dust when handling and mixing. For skin contact, remove contaminated clothing and wash with soap and water. Keep out of reach of children, and do not eat, drink or smoke while using it. Refer to the Safety Data Sheet (SDS) for full details.
$137.46
Sika MonoTop-352 NFG is a lightweight, high-build structural repair mortar for damaged and spalled concrete, supplied here as a 20kg bag in grey powder form. It is a one-component, polymer-modified, fibre-reinforced mix with a built-in corrosion inhibitor, and it meets Class R3 of EN 1504-3. It suits both hand application and wet-spray machine application.About the formulaThe mortar is based on sulphate resistant cement, selected lightweight aggregates, a corrosion inhibitor and polymer modification. Sika describes it as low shrinkage, low permeability and sulphate resistant. The low density makes it easier to build up thickness while still being suitable for structural repair. On a well prepared, roughened substrate a bonding primer is generally not needed, even when applying by hand. It can also be used as a repair mortar before Sikagard 62 and 63N coatings, and it is compatible with the Sika FerroGard sacrificial anode system.Where to use itIndoors: repairing spalled or damaged concrete in buildings, including structural elements and superstructure works.Outdoors: repairing concrete in bridges and other infrastructure, and restoring cover over reinforcement where concrete has been contaminated or carbonated.Suitable for concrete repair, including restoration work and structural strengthening as set out in EN 1504-9. Layers can be built from 4mm up to 75mm in a single application.How to use it Prepare the area first. Remove loose, contaminated and deteriorated material and clean any exposed reinforcement of rust, scale and dust. Roughen the substrate using abrasive blasting or high pressure water-blasting. Pre-wet the prepared substrate about 2 hours before application and keep it in a saturated surface dry (SSD) condition. Pour 2.8 to 3.3 litres of clean water into a suitable container for each 20kg of powder. Add the powder while stirring slowly. Mix thoroughly for at least 3 minutes, using a low speed drill mixer (under 500 rpm) or a forced-action mixer for machine application. Small amounts can be mixed by hand. Apply by trowel, pressing the mortar firmly onto the substrate, or by wet-spray equipment. Finish once the mortar begins to stiffen. Protect the fresh mortar straight away from premature drying using a suitable curing method, such as a curing compound, damp geotextile or polythene sheet. Important notesApply only to sound, properly prepared substrate. Do not exceed the recommended water dosage, and do not add extra water while finishing, as this can cause discolouration and cracking. Avoid application in direct sun or strong wind, and protect freshly applied material from freezing. The recommended ambient and substrate temperature range for application is +5 °C to +30 °C. Final set is about 6 hours. For critical or structural repairs, follow the current Sika Product Data Sheet and the Sika method statement for concrete repair.Specifications Brand Sika Product MonoTop-352 NFG Structural Repair Mortar Pack 20kg bag Colour Grey powder Base Sulphate resistant cement, corrosion inhibitor, lightweight aggregates, polymer modified Application Hand (trowel) or wet-spray machine Layer thickness 4mm minimum, 75mm maximum per layer Mixing water 2.8 to 3.3 litres per 20kg Yield About 12.8 litres of mortar per 20kg Consumption About 15.6kg of powder per cm thickness per m² Fresh mortar density About 1.8 kg/l Maximum grain size 2mm Final set About 6 hours Standard Class R3 of EN 1504-3 Shelf life 12 months in unopened, undamaged packaging, stored dry and cool Use Interior and exterior concrete repair SafetyThis is a cement-based powder. Hazards include skin irritation, possible allergic skin reaction, serious eye damage and respiratory irritation. Avoid breathing dust, use in a well-ventilated area, and wear protective gloves and eye or face protection. Wash skin thoroughly after handling and do not wear contaminated work clothing out of the workplace. Refer to the Safety Data Sheet (SDS) for full details.
$100.25
Dingo Structural Mortar Repair is a polymer-modified, fibre-reinforced repair mortar for restoring damaged concrete and masonry, supplied here as a single 10kg bag of dry powder. It is a ready-to-mix, one-component product that you simply combine with clean water, and it is built for structural-grade repairs on both horizontal and vertical surfaces, above or below ground.About the formulaThis is a lightweight, low-shrinkage, cement-based mortar that is modified with polymers and reinforced with fibres to help limit micro cracking. According to the manufacturer it meets the requirements of class R3 under EN 1504-3. The powder is based on sulphate resistant cement, selected lightweight aggregates and additives, and it gives repairs better resistance to oils, sewage and chemicals. It can be built up in layers of up to 75mm thick.Where to use itIndoors: patching cavities, voids and honeycombed areas in concrete or mortar, and repairing brickwork.Outdoors: repairing spalled concrete caused by corroding reinforcement, and fast repairs to horizontal or vertical concrete and mortar surfaces above and below ground level. The manufacturer also lists building, bridge and infrastructure repair work and structural strengthening among its uses.Suitable substrates include concrete, mortar, brick and block masonry that is clean, sound and free of oil, grease and loose material.How to use itLay out your tools before you start. Pour the amount of powder you need into a clean bucket and add clean water gradually. A full 10kg bag needs roughly 1.6 to 1.7 litres of water. Mix mechanically for at least 3 minutes using a low-speed drill and paddle mixer until the mix is consistent. Use the mixed material as soon as possible after opening the bag. Apply it to the prepared surface by hand or by mechanical methods.Important notesMix only what you can use promptly, and only with clean water. One 10kg bag yields roughly 6.5 litres of mortar. How much you need depends on how rough the surface is and how thick the layer is. Keep unopened bags in a cool, dry, sheltered place out of harsh weather. For large, load-bearing or engineered structural repairs, check the manufacturer's Product Data Sheet and get advice from the manufacturer or a qualified engineer.Specifications Brand Dingo Product Structural Mortar Repair Pack 1 x 10kg bag Form / colour Powder, grey Base Polymer-modified, fibre-reinforced cementitious mortar (sulphate resistant cement) Application Mix with water; apply by hand or mechanically Mix water About 1.6 to 1.7L per 10kg bag Yield About 6.5L of mortar per 10kg Maximum layer thickness 75mm Standard Class R3 of EN 1504-3 Use Interior and exterior SafetyThis is a cement-based powder. Mixing it may irritate the eyes and skin, and prolonged contact can cause dermatitis and alkaline burns. The dust irritates the eyes, skin and respiratory system. Avoid contact with the eyes and skin, wear protective clothing, gloves and eye protection, and wear a suitable dust mask when handling the dry powder. Refer to the Safety Data Sheet (SDS) for full details.
$33.82
Gyprock Pro-Repair 10 is a fast-setting, plaster-based jointing and patching compound, supplied here as an 8kg bag for small jointing jobs and everyday wall and ceiling repairs. It gives you roughly ten minutes of working time once mixed, so you can fill, tape and move on without waiting for a slow-drying compound to dry. It suits tradies, renovators and keen DIYers who want quick results.About the formulaPro-Repair 10 is a lightweight, low-VOC powder that you mix with water. It is a setting compound, so it hardens by chemical reaction rather than by evaporation. It is tinted so repairs are easy to spot on painted surfaces. It is designed to stick well to jointing tape, to shrink very little, and to sand easily as a topcoat. You can use it for every coat of a three-coat joint or as a base coat only. If you use it for all three coats with an open-weave fibreglass tape such as FibaFuse, you can sand the topcoat on the same day once it has dried enough. It is made in Australia by CSR Gyprock.Where to use itIndoors: patching holes, nicks, cracks and other defects in new and existing plasterboard walls and ceilings, and jointing smaller residential or commercial rooms.Fibre cement: suitable for repairs and jointing on Cemintel fibre cement sheet as well as Gyprock plasterboard.Suitable surfaces are Gyprock plasterboard and fibre cement. It is not recommended for wet areas.How to use itStart with a clean, dust-free surface. Tear the bag open at a top corner and mix with clean water as directed on the pack. Because the working time is short, mix only as much as you can use in one go. Apply by hand with a knife or similar tool. Embed the jointing tape in the base coat, then add further coats as needed. Let the compound dry fully, then sand the topcoat smooth before you prime and paint. Throw away any mixed compound you have not used. Keep unused powder in its original bag with the top rolled down, inside an airtight container.Important notesPro-Repair 10 is a setting compound, so you cannot rework it once it has started to set. Do not add water to extend the working time. It is not recommended for wet areas. Shelf life is one year from the date of manufacture, so store the bag somewhere dry and out of the weather and direct sun. Allow enough drying time before sanding, even when you are finishing the job on the same day.Specifications Brand Gyprock (CSR) Product Pro-Repair 10 Jointing and Patching Compound Pack 8kg bag Form Dry powder, mix with water (not pre-mixed) Base Lightweight plaster-based setting compound Application Hand applied Working time About 10 minutes after mixing Setting time About 30 minutes Coverage About 13kg per 100m² Suitable surfaces Plasterboard and fibre cement Shelf life 1 year from manufacture Standard Used in line with AS/NZS 2589 (Gypsum linings, application and finishing) Origin Australian made SafetyDust can irritate the eyes and may aggravate existing eye conditions, so avoid breathing dust and avoid eye contact and prolonged skin contact. Wear gloves, eye protection and a dust mask when mixing and sanding. In case of eye contact, flush thoroughly with running water for 15 minutes with the eyelids held open. Store in a cool, dry, well-ventilated place out of direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$50.21
Davco Ultraflex is a premium grade, cement-based tile adhesive for walls and floors, supplied here as a 20kg bag for full tiling jobs. It is rubber modified, so it suits both rigid and flexible substrates, and it is rated for commercial work as well as home renovations.About the formulaA powder adhesive that you mix with clean water and apply with a notched trowel. The rubber modification gives it extra flexibility over framed and sheet substrates. It is suitable for use over early age screed (cured for 24 hours) and over under-tile heating. It is classified C1S1E under AS ISO 13007 and has a low VOC content of 5 g/L (SCAQMD method 304-91).Where to use itIndoors: living and dining areas, walkways and office spaces, on both walls and floors.Outdoors: external verandahs and decks, on both walls and floors.Suitable tiles include porcelain, ceramic, mosaic, terracotta, slate, quarry, granite and marble. Suitable substrates include cement render, blockwork and rendered brickwork, plasterboard, fibre cement sheet, compatible waterproofing membranes, timber floors (with fibre cement tile underlay installed), new concrete (cured for 7 days) and new screed (cured for 24 hours). The adhesive is not suitable for translucent tiles or for moisture sensitive stone such as green marble.How to use itMake sure the substrate is sound, firmly fixed, clean and free of dust, oil and loose material. Prime the surface where the data sheet calls for it (for example plasterboard, fibre cement sheet, screed and timber floors with tile underlay), using the Davco primer the manufacturer recommends for that substrate. Mix the powder with clean potable water to a smooth, lump-free consistency, about 7 litres of water per 20kg bag. Spread the adhesive with a notched trowel suited to your tile size and press the tiles firmly into place. A 20kg bag covers about 12m2 when applied with a 6mm notch trowel, and less with larger trowels. Clean tools with water while the adhesive is still fresh, and wipe wet adhesive off tile faces with a damp cloth. Cured adhesive is much harder to remove.Important notesAllow 6 to 8 hours before grouting. Check the manufacturer's data sheet for substrate preparation, primers and movement joint requirements before you start. Store unopened bags off the ground in cool, dry conditions. Shelf life is up to 12 months when stored this way. If you plan to use it on a surface or in an application not covered by the data sheet, contact the manufacturer first.Specifications Brand Davco Product Ultraflex Premium Grade Cement-Based Tile Adhesive Pack 20kg bag Base Cement-based, rubber modified powder Application Mixed with water, applied by notched trowel Coverage About 12m2 per 20kg bag (6mm notch trowel) Time before grouting 6 to 8 hours Classification C1S1E (AS ISO 13007) VOC content 5 g/L (low VOC) Use Interior and exterior, walls and floors, commercial and domestic SafetyThis product contains cement, which is alkaline and can cause dermatitis. Wear PVC or similar gloves and safety goggles when mixing and applying. Avoid breathing in the dust when opening bags and mixing, and use suitable dust protection where needed. Wash skin with water after contact. Refer to the Safety Data Sheet (SDS) for full details.
$40.69
Bastion Mastic Tile Adhesive is a white, cement-based powder adhesive for fixing wall and floor tiles, supplied here in a 20kg bag for larger tiling jobs. It is a non-slump mix, so tiles stay where you put them on vertical surfaces. It suits both interior and exterior tiling.About the formulaA cement-based powder that you mix with clean water to a thick, creamy, lump-free mortar. The non-slump body helps tiles hold their position on walls. The manufacturer data sheet lists an open time of 15 minutes and an adjustment time of 20 minutes. Site conditions affect these times, so only spread as much adhesive as you can tile before it skins over.Where to use itIndoors: wall and floor tiling over concrete, renders and screeds.Outdoors: external wall and floor tiling on the same types of substrate.Suitable tile types listed by the manufacturer are ceramic tiles, porcelain, glass mosaics and natural stone (excluding moisture-sensitive stone). Suitable substrates are concrete, renders and screeds.How to use itAdd the powder to clean water in a large, clean container while stirring vigorously with a paddle mixer. A 20kg bag needs about 6 litres of water. Mix for several minutes, leave it to stand for five minutes, then remix. As a general guide, use a notched trowel of at least 6 x 6 x 6mm on walls and at least 10 x 10 x 10mm on floors. The adhesive can be applied at a bed thickness of more than 3mm and less than 10mm. Check that there are no voids under the tile and do not spot fix.Important notesNot suitable for moisture-sensitive or dimensionally unstable natural stone. Coverage varies with substrate condition, tile type and technique. As a guide, a 20kg bag covers about 10m2 on walls with a 6mm notched trowel, or about 7m2 on floors with a 10mm notched trowel. Always check the current data sheet and SDS for shelf life, curing and grouting times, and any limits for your tile and substrate.Specifications Brand Bastion Product Mastic Tile Adhesive Powder Pack 20kg bag Colour White / off white Base Cement-based powder, non-slump Mixing ratio About 6 litres of water per 20kg bag Application Notched trowel Open time 15 minutes Adjustment time 20 minutes Bed thickness More than 3mm and less than 10mm Coverage (20kg) About 10m2 on walls (6mm trowel), about 7m2 on floors (10mm trowel) Use Interior and exterior, walls and floors SafetyThe manufacturer notes that this product may cause skin irritation and an allergic skin reaction. It may also cause serious eye injury and irritation of the respiratory system. Wear protective gloves and eye protection, and avoid breathing the dust when handling the dry powder. Refer to the Safety Data Sheet (SDS) for full details.
$28.62
The Gyprock Rapid Repair Kit is a complete, ready-to-go pack for patching damaged plasterboard walls and ceilings, from small nicks and cracks through to holes up to 150mm x 150mm. Everything needed for the job is supplied in one mixing bucket, so a first-time DIYer can go from damaged wall to a surface ready for paint without hunting down separate products or tools.About the formulaThe compound in the kit is Gyprock Rapid Patch, a fast-setting dry powder that you mix with clean water into a smooth paste. Gyprock lists a working life of around 20 minutes once mixed, with minimal shrinkage when filling small cracks and dents, and a surface that is ready to sand in around 40 minutes. Gyprock lists the powder at a specific gravity of 2.3 to 2.4 and a low VOC content, under 10 g/L per material. The kit is made in Australia by CSR Gyprock.What is in the kit 1kg bag of Gyprock Rapid Patch compound 2 x Gyprock plasterboard repair panels (150mm x 150mm) for larger holes Gyprock Easy Tape (20 metres) 100mm broadknife Sanding block Mixing bucket (also the kit's packaging) Step-by-step instructions Where to use itIndoors: patching dents, scratches, cracks and holes in plasterboard walls and ceilings, including door-handle dings and holes left by removed fixings or fittings.Other substrates: the Rapid Patch compound itself is also rated by Gyprock for repairs to fibre cement, timber and masonry, and it can be used as an all-purpose compound for setting plasterboard joints. Check the substrate and the finish before using it in damp areas.Suitable materials include plasterboard (the main use of the kit), fibre cement, timber and masonry (the compound only).How to use itRemove any loose paint or crumbling material around the damage and lightly sand the edges. Mix the powder with clean water to a creamy consistency. Gyprock's guide for small repairs is about 1 cup (260g) of powder to 150mL of water. Only mix as much as you can use in around 20 minutes. For small nicks and cracks, fill with the broadknife, let it set, then sand smooth. For larger holes, cut and fit a repair panel with backing blocks fixed using the compound, cover the joins with Easy Tape, and apply compound over the tape. Let each coat set fully before the next, then sand lightly and the wall is ready to paint.Important notesUse clean domestic water for mixing, and wash tools before the compound sets. The kit is aimed at repairs up to 150mm x 150mm, so larger damage will need a bigger repair. You may also need a hand saw, trimming knife, pencil, dust mask and eye protection depending on the job. Store unused compound dry, out of the weather and out of direct sunlight.Specifications Brand Gyprock (CSR) Product Rapid Repair Kit Pack Single kit, 1.5kg nominal (1kg Rapid Patch compound plus panels, tape and tools) Base Plaster-based dry powder, mixed with water Application Hand applied with the supplied broadknife Working time (Rapid Patch) About 20 minutes Ready to sand (Rapid Patch) About 40 minutes Repair size Up to 150mm x 150mm Specific gravity 2.3 to 2.4 VOC content Under 10 g/L per material Suitable surface Plasterboard walls and ceilings Origin Made in Australia SafetyCutting, sanding or grinding the set material makes dust that can irritate the eyes, nose and throat, so wear a dust mask and eye protection and avoid prolonged skin contact. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$49.75
Gyprock Masonry Adhesive is a dry powder adhesive made for fixing plasterboard directly to masonry and concrete walls, supplied here in a 20kg bag for full-room and trade-sized jobs. You mix it with water on site to a firm, creamy paste. It is also used to fix plaster cornice and decorative plaster castings to plasterboard walls and ceilings in residential and commercial buildings.About the formulaThis is a plaster-based, setting-type compound rather than a drying type. Once mixed, it has a working life of about 40 to 45 minutes before it starts to set. The manufacturer designs it for strong adhesion and good initial grab, and it is easy to spread by hand with a small broadknife. It is made in Australia by CSR Gyprock. The manufacturer lists a very low VOC content of 2g/L (as specified by GBCA) and notes the product is GECA accredited.Where to use itIndoors: direct-fixing plasterboard sheets to brick, block and concrete internal walls, and fixing plaster cornice and plaster castings to plasterboard walls and ceilings.Outdoors: not intended for external use. It is an internal wall lining adhesive.Suitable surfaces include brick, concrete and other masonry, plus plasterboard for cornice and casting work. Remove any paint from the areas where the adhesive will be applied.How to use itPour the powder slowly into clean domestic water and mix to a firm, creamy consistency. The manufacturer's guide is roughly 3kg of powder to 1.5 litres of water. Mix only what you can use within the working life, and never mix or re-work adhesive once it has begun to set or dry. For plasterboard, apply daubs of about 50mm diameter that stand out at least 15mm from the wall. Keep daubs no more than 450mm apart horizontally and vertically, and keep them about 50mm in from sheet ends and edges. You can apply daubs to either the wall or the back of the sheet. Position the board and hold it in place until the adhesive sets. Use levelling pads where wall irregularities exceed 15mm. Always follow the current Gyprock installation guides for full fixing details.Important notesNot suitable for use on wet area plasterboard in tiled areas. Use only clean domestic water for mixing. Keep fresh batches free from contamination and do not mix with set or drying material. The bag is non re-sealable, so plan the quantity you need. Shelf life is 12 months from the date of manufacture when the bags are stored dry, out of the weather and away from direct sunlight. Wall suitability, fixing limits and any decoration requirements should be checked against the Gyprock Red Book and technical data sheet for your job.Specifications Brand Gyprock (CSR) Product Masonry Adhesive Pack 1 x 20kg non re-sealable bag Form Dry powder (mix with water) Colour Off white Base Plaster-based setting compound Application By hand with a broadknife, applied as daubs Working life once mixed 40 to 45 minutes Coverage 20kg fixes approximately 30m2 of plasterboard Specific gravity 2.3 to 2.4 VOC content (GBCA) 2g/L Shelf life 12 months from manufacture Origin Made in Australia Use Interior SafetyAvoid eye contact and repeated or prolonged skin contact, and avoid breathing in the powder dust when opening, pouring and mixing. Wear gloves and eye protection, and use a dust mask or respirator in dusty conditions, especially when sanding or cutting set material. Wash well after handling. Store bags in a dry place, protected from weather and direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$71.12
Gyprock DIY Cornice Cement is a powder-based, mix-with-water adhesive made for fixing cornice at the wall and ceiling junction, supplied here in a handy 2.5kg bag for small rooms, repairs and touch-ups. It is a setting-type compound rather than a drying type, so it grabs well at the start and builds a high bond strength once set. It is made in Australia by CSR Gyprock.About the formulaA dry plaster-based powder that you mix with clean water into a workable paste. Once mixed, you get a working life of roughly 50 to 60 minutes, which is enough to fix several lengths of cornice and tidy the joints without rushing. Because it sets by reaction rather than by drying out, it hardens in a predictable timeframe. Gyprock describes it as a low VOC product.Where to use itIndoors: fixing Gyprock cornice at wall and ceiling junctions where the lining is plasterboard or fibre cement, finishing cornice joints and mitres, filling small gaps along the cornice line and carrying out small cornice repairs.Outdoors: not intended for exterior use. It is designed for interior cornice work.Suitable surfaces are plasterboard and fibre cement wall and ceiling linings, bonded to Gyprock cornice.How to use itCut cornice sections to length using a saw and mitre box or a mitre guide. Add 2kg of powder to 1.1 litres of clean water and mix to a creamy consistency. Only mix as much as you can use within the 50 to 60 minute working life. Apply the cement with a broadknife as a bead along both back edges of the cornice and onto the mitres. Butter and fix each length separately, starting with the shorter lengths. Hold each piece in place with temporary nails or screws, then remove the surplus cement and clean off with a brush or sponge. Smooth the mitres and fill any gaps with more cement. Leave it to set for at least 2 hours before removing the temporary fixings and sanding the joints.Important notesThe bag is not re-sealable, so plan your batches and keep the bag closed and dry between uses. Shelf life is 12 months from the date of manufacture. Do not mix more than you can use in the working time, and do not re-use material that has started to stiffen. Gyprock lists this product for residential cornice fixing and repairs on plasterboard and fibre cement. Clean tools with water before the cement sets.Specifications Brand Gyprock (CSR Gyprock) Product DIY Cornice Cement 60 Pack 2.5kg bag Colour Off white Base Plaster-based powder, setting type Application Mixed with water, applied with a broadknife Mix ratio 2kg powder to 1.1 litres of water Working time 50 to 60 minutes after mixing Set before sanding At least 2 hours Specific gravity 2.3 to 2.4 VOC content 2g/L Shelf life 12 months from manufacture Origin Made in Australia Use Interior SafetyDust created when sanding or cutting the set material is a nuisance dust, so keep dust low, work in a ventilated space and wear gloves, eye protection and a suitable dust mask when sanding. If it gets in your eyes, flush with plenty of running water, holding the eyelids open, for about 15 minutes. Store the bag in a dry place and keep it out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$25.27
Dunlop Wide Joint Grout is a cement-based tile grout purpose-made for the big joints that standard grouts can't handle, filling gaps from 5mm right up to 50mm wide. In a practical Mid Grey colour, it suits rustic and heavy-duty tiling styles where wide grout lines are part of the look, curing to a hard-wearing finish indoors and out.Where to use itUse it on walls and floors, indoors and outdoors, over ceramic tiles, terrazzo, quarry tiles and sealed terracotta and slate. It is the go-to grout for terracotta paving, quarry tile floors, feature walls and any tiled area with generous joint widths.How to useMix the powder with clean water to a firm, workable consistency and work it into the joints with a grout float, compacting well so the full joint depth is filled. Strike off excess on the diagonal, then clean the tile faces with a damp sponge once the grout has firmed. Porous tiles such as terracotta and slate should be sealed before grouting to prevent staining.Important notesDesigned for joints 5-50mm wide; for narrower joints use Dunlop Flexible Coloured Grout. Coverage varies with tile size and joint dimensions. Protect fresh grout from rain and frost while curing.Specifications Size 15kg bag Colour Mid Grey Joint width 5-50mm Tile types Ceramic, terrazzo, terracotta, slate, quarry tiles Coverage Approx. 9m² (200x200x10mm tiles, 8mm joint) to 11m² (600x600x10mm, 20mm joint) per 15kg Location Indoor and outdoor, walls and floors SafetyCement-based powder - alkaline when wet. Wear gloves, safety glasses and a P2 dust mask when mixing, keep the work area ventilated, avoid prolonged skin contact and wash hands after use. Keep out of reach of children.
$41.19
Dunlop Multipurpose Acrylic Render is a high-performance, polymer-modified render engineered for superior trowelability and a no-sag, no-crack result even at higher builds. It can be applied from 2mm right up to 10mm in thickness without slumping, which makes it equally at home as a levelling base coat over rough masonry or as a straightening coat before a fine or textured finish. One bag covers the jobs a standard sand-and-cement mix struggles with, while remaining easy to rule off and float.Where to use itFor indoor and outdoor rendering over AAC panels and blocks, brickwork, concrete blockwork and concrete walls. Use it to render new masonry, level uneven walls, and build out hollows before finishing with Dunlop Ready-to-Go Render, Fine Coat Render or Coloured Render Texture Coat.How to usePrepare a clean, sound, dust-free substrate and dampen very porous masonry or apply the recommended primer. Mix the powder with clean water to a smooth, workable consistency, then apply with a steel trowel at 2-10mm. Rule off with a straight edge, allow to firm, then float or sponge to the desired surface. The Dunlop Gauging Trowel helps achieve a professional finish. As a guide, 20kg covers approximately 6.5m² at 2mm, 2.6m² at 5mm or 1.3m² at 10mm thickness.Important notesDo not exceed 10mm per coat — build very deep sections in multiple passes. Avoid application in direct hot sun, high wind or onto frozen or saturated substrates, and protect fresh render from rapid drying. Allow to cure fully before over-coating or painting.Specifications Size 20kg bag Colour Light Grey Coverage 6.5m² at 2mm, 2.6m² at 5mm, 1.3m² at 10mm per bag Application thickness 2-10mm SafetyContains cement — wet render is alkaline and can irritate or burn skin and eyes. Wear gloves, eye protection and a dust mask when mixing, avoid breathing dust and wash skin promptly after contact. Read the Safety Data Sheet before use.
$23.55
Dunlop Flexible Fine Coat Render is a high-performance, fibre-reinforced, polymer-modified render that produces a fine, closed finish with superior adhesion and flexibility. The embedded fibres and flexible polymers allow the render to tolerate the minor movement common to sheeted and composite walls, dramatically reducing the risk of surface cracking. It can be applied by standard trowelling methods or by spray, and a variety of decorative finishes can be achieved depending on how it is floated or sponged.Where to use itSuitable for indoor and outdoor use over an unusually wide range of substrates: FC sheet and blueboard, concrete and blockwork, sound painted surfaces (alkali stable and water resistant), existing render, AAC panels and blocks, and EPS foam panels. It is the go-to finishing render where substrate movement or mixed materials would defeat a rigid render.How to useEnsure the substrate is clean, sound and free of dust, oil and loose coatings; prime where the system requires. Mix the powder with clean water to a smooth, lump-free consistency and apply by steel trowel or spray at 2-10mm thickness. Rule off, allow the render to firm, then float, sponge or texture to the desired finish. A 20kg bag covers approximately 6.5m² at 2mm or 2.6m² at 5mm thickness. Clean tools with water before the render sets.Important notesStay within the 2-10mm application range per coat. Avoid rendering in extreme heat, wind or imminent rain, and protect the fresh surface from rapid drying. Painted substrates must be firmly bonded, alkali-stable and water resistant.Specifications Size 20kg bag Colour Grey Coverage 6.5m² at 2mm or 2.6m² at 5mm per bag Application thickness 2-10mm Reinforcement Fibre-reinforced, polymer modified SafetyCement-based powder — the wet mix is alkaline and dust can irritate airways. Wear gloves, safety glasses and a P2 dust mask when mixing, work in ventilation and wash skin after contact. Refer to the Safety Data Sheet before use.
$39.21
Dunlop Ardit Construction Grout in the full-size 20kg bag is a high-strength, multipurpose construction grout that mixes to either a non-slump paste or a flowable consistency to suit a wide range of projects. Its extended working time allows extra minutes for accurate positioning before set, and the non-shrink formulation locks components firmly in place. The grout achieves approximately 45MPa after 7 days and around 65MPa at 28 days, and carries a 10 year guarantee, making it a dependable choice for structural packing and grouting work.Where to use itDesigned for indoor and outdoor use in general construction grouting and machine grouting applications: grouting under machine bases, baseplates and stanchions, filling voids, pockets and core holes in concrete, bedding structural members, and anchoring bolts, rails and fixings into concrete and masonry. Application thickness ranges from 5mm to 100mm.How to useEnsure surfaces are structurally sound, clean and free of dust, oil and laitance, and pre-dampen porous substrates. Mix with clean water to the consistency required — a stiff non-slump mix for hand packing and trowelling, or a flowable mix for pouring into formwork and confined spaces. Place within the working time and compact well to eliminate air voids. A 20kg bag yields approximately 11.2L as a non-slump mix or 12.0L as a flowable mix.Important notesKeep within the 5-100mm application range. Avoid adding excess water, which lowers strength and increases shrinkage risk. Low temperatures slow strength development; protect fresh grout from rapid drying in hot or windy conditions.Specifications Size 20kg bag Colour Grey Yield 11.2L per 20kg (non-slump), 12.0L per 20kg (flowable) Compressive strength Approx. 45MPa (7 days), 65MPa (28 days) Application thickness 5-100mm SafetyCement-based product — wet grout is alkaline and may cause skin and eye irritation. Wear protective gloves, eye protection and a P2 dust mask when mixing. Avoid breathing dust. Consult the Safety Data Sheet before use and store in a dry place out of reach of children.
$42.23
Dunlop General Purpose Construction Grout is an economical, high-strength cementitious grout that can be mixed to a dry pack, plastic or flowable state, giving one bag remarkable versatility across construction and repair tasks. The shrinkage-compensated formulation holds its volume as it cures, and strength development is impressive for a general purpose product — approximately 70MPa at 7 days and up to 85MPa at 28 days when mixed as a dry pack with 12% water.Where to use itSuited to indoor and outdoor projects wherever a dependable, high-strength grout is needed: packing under baseplates and machinery, filling voids, holes and pockets in concrete, bedding posts and bollards, grouting anchor bolts and starter bars, and general making-good around concrete and masonry. Application thickness ranges from 10mm up to 100mm.How to useStart with a clean, sound substrate free of dust, oil and loose particles, and dampen absorbent surfaces before grouting. Add clean water to achieve the consistency the job requires — dry pack for ramming into confined spaces, plastic for trowel placement, or flowable for pouring. Compact or rod the grout to remove entrapped air and finish with a steel trowel. A 20kg bag yields approximately 9.5L as dry pack, 10.3L at plastic consistency or 10.9L as a flowable mix. Varying the water ratio changes both workability and final strength.Important notesHigher water contents make placement easier but reduce ultimate strength — use the minimum water needed for workability. Maintain the 10-100mm thickness range and protect fresh grout from freezing and from rapid drying.Specifications Size 20kg bag Colour Grey Yield 9.5-10.9L per 20kg depending on consistency Compressive strength Approx. 70MPa (7 days), 85MPa (28 days) as dry pack Application thickness 10-100mm SafetyContains portland cement — wet product is alkaline and can burn skin and eyes on prolonged contact. Wear gloves, safety glasses and a dust mask when mixing, and avoid breathing dust. Read the Safety Data Sheet before use.
$26.30
Dunlop Ardit Construction Grout is a high-strength, cement-based grout that can be mixed to either a stiff, paste-like consistency or a free-flowing pour, making it a genuine all-rounder for construction and repair work. Formulated with Ardit Technology and an extended working time, it gives you more room to position components accurately before the mix begins to set. This non-shrink formulation reaches approximately 45MPa after 7 days and around 65MPa at 28 days, and it is backed by a 10 year guarantee. The handy 5kg bag suits smaller jobs and repairs without the waste of a full-size bag.Where to use itSuitable for indoor and outdoor projects wherever a high-strength, non-shrink grout is required — general construction grouting, machine and equipment base grouting, filling voids and pockets in concrete, bedding and packing under plates, and anchoring bolts, rails and posts. It performs over concrete and masonry substrates at application thicknesses from 5mm up to 100mm.How to usePrepare a sound, clean substrate free of dust, oil and loose material, and pre-dampen absorbent surfaces. Mix the powder with clean water to the consistency the job calls for — non-slump paste for vertical packing or a flowable mix for pouring into forms and voids. Place the grout within its working time, compacting or rodding to remove air pockets, then finish with a trowel. As a guide, a 20kg quantity yields roughly 11.2L as a non-slump mix or 12.0L as a flowable mix, so expect around a quarter of that from this 5kg bag.Important notesApply between 5mm and 100mm thickness. Do not over-water the mix, as excess water reduces final strength. Cold or damp conditions extend curing times; hot, windy conditions shorten working time.Specifications Size 5kg bag Colour Grey Yield Approx. 2.8-3.0L per 5kg depending on consistency Compressive strength Approx. 45MPa (7 days), 65MPa (28 days) Application thickness 5-100mm SafetyContains cement — the wet mix is alkaline and can irritate skin and eyes. Wear gloves, safety glasses and a dust mask when handling the dry powder, work in a ventilated area and wash hands after use. Refer to the Safety Data Sheet before use and keep out of reach of children.
$23.73
Dunlop Flexible Coloured Grout in the trade-size 15kg bag is built for big tiling jobs - whole houses, commercial floors and multi-room renovations. It is the same flexible, smooth-finish formula tilers rely on, with a stronger colour system for rich, even grout lines and Grout Shield anti-mould and anti-bacteria technology that resists mould and bacteria growth in wet areas. The grout works easily, ensures flush joints and leaves no pin holes.Where to use itSuitable for walls and floors, indoors and outdoors, over ceramic, porcelain, marble, granite and mosaic tiles. With a working range of 1mm to 8mm joints it handles fine wall tiling through to wide-format floor tiles, and the grey tones (Misty Grey and Slate Grey) are popular choices for high-traffic floors where joints need to hide everyday wear.How to usePrepare clean, dry joints raked free of adhesive. Mix with clean water to a smooth paste - or with Dunlop Primer & Additive to boost colour, flexibility, adhesion and stain resistance. Apply diagonally with a rubber grout float, pack joints full, remove excess, then sponge the tiles clean once the grout firms and polish off haze. Initial set is around 24 hours, showers can be wet after 3 days, and full cure is reached after 7 days.Important notesInclude about 15% wastage in quantity estimates. Mix batches with consistent water content to avoid colour variation across large floors.Specifications Joint width 1 - 8mm Coverage guide Approx. 0.55kg/m² for 200 x 200 x 8mm tiles at 3mm joints Tile types Ceramic, porcelain, marble, granite, mosaics Location Walls and floors, indoor and outdoor SafetyCement-based product - alkaline when wet and may irritate skin and eyes. Wear gloves and eye protection, avoid inhaling dust when emptying and mixing the bag, and wash after use. Keep out of reach of children; see the Safety Data Sheet.
$79.95
Dunlop Ultra-White Grout is a non-sanded, flexible cement-based grout that delivers a super smooth, brilliantly white finish between wall and floor tiles. Formulated with Grout Shield anti-mould and anti-bacteria technology, it actively resists the growth of mould and bacteria so joints stay looking cleaner for longer. The cured grout is water repellent, resists dirt pick-up and is easy to wipe clean, making it a favourite for bright, fresh bathrooms and kitchens.Where to use itUse Ultra-White Grout on walls and floors, indoors and outdoors. It is suited to ceramic, porcelain, marble, granite and mosaic tiles, and is designed for narrow tile joints between 1mm and 4mm wide where a fine, non-sanded finish is wanted.How to useEnsure joints are clean, dry and free of dust or adhesive residue. Mix the powder with clean water to a smooth, lump-free paste, then work the grout firmly into the joints on the diagonal using a rubber grout float or squeegee. Remove the excess as you go, then clean the tile faces with a lightly damp sponge once the grout has firmed. Polish off any remaining haze with a soft, dry cloth. Allow the grout to cure fully before exposing wet areas such as showers to water.Important notesCoverage varies with tile size, joint width and joint depth, and a wastage allowance of around 15% should be included when estimating. For wide joints over 4mm choose a sanded or wide-joint grout instead. Pair with Dunlop Grout Sealer for extra stain protection.Specifications Joint width 1 - 4mm Coverage guide Approx. 6.7m² for 300 x 300 x 5mm tiles at 3mm joints (incl. 15% wastage) Tile types Ceramic, porcelain, marble, granite, mosaics Location Walls and floors, indoor and outdoor SafetyCement-based product - the wet mix is alkaline and may irritate skin and eyes. Wear gloves and eye protection, avoid breathing dust when mixing, and wash hands after use. Keep out of reach of children and refer to the Safety Data Sheet before use.
$15.23
Dunlop Ultra-White Grout in the 5kg pack is a non-sanded, flexible grout that produces a super smooth, super white finish across larger tiling jobs. It contains Grout Shield anti-mould and anti-bacteria technology to resist mould and bacteria growth, and the cured joint is water repellent and easy to clean, helping white joints stay bright in busy bathrooms, laundries and kitchens.Where to use itSuitable for tile joints on walls and floors, indoors and outdoors. Use it with ceramic, porcelain, marble, granite and mosaic tiles wherever joints are between 1mm and 4mm wide. The 5kg pack size suits full bathroom renovations, splashback runs and floor areas where a 1.5kg pack would run short.How to usePrepare joints so they are clean, dry and raked free of adhesive. Mix the powder with clean water to a smooth, creamy paste and let it stand briefly before remixing. Apply diagonally across the joints with a rubber grout float, pressing the grout in fully and striking off the excess. Once firm, sponge the tile faces clean with minimal water, then buff away the haze with a dry cloth. Keep showers dry until the grout has cured.Important notesEstimate quantities from tile size, joint width and depth and allow roughly 15% extra for wastage. Not intended for joints wider than 4mm. Sealing with Dunlop Grout Sealer after curing improves long-term stain resistance.Specifications Joint width 1 - 4mm Coverage guide Approx. 13.3m² for 300 x 300 x 5mm tiles at 1.5mm joints (incl. 15% wastage) Tile types Ceramic, porcelain, marble, granite, mosaics Location Walls and floors, indoor and outdoor SafetyContains cement - wet grout is alkaline and can irritate skin and eyes. Wear gloves and safety glasses, avoid inhaling dust while mixing, and wash thoroughly after handling. Keep out of reach of children and consult the Safety Data Sheet.
$41.03
Dunlop Flexible Coloured Grout in the 5kg pack brings the same smooth finish and strong, consistent colour as the smaller pack, in a size suited to whole bathrooms, kitchens and floor areas. The formula is flexible and easy to work, ensures flush joints with no pin holes, and contains Grout Shield anti-mould and anti-bacteria technology that resists mould and bacteria growth so grout lines stay looking better for longer.Where to use itGrout walls and floors indoors and outdoors with ceramic, porcelain, marble, granite and mosaic tiles. Joints from 1mm to 8mm are covered, making it suitable for everything from fine mosaic work to wide-format floor tiles. In swimming pools, use White 200 mixed with Dunlop Primer & Additive.How to useRake joints clear of adhesive and ensure they are clean and dry. Mix the powder with clean water to a smooth, lump-free paste - or gauge with Dunlop Primer & Additive for enhanced colour, adhesion, abrasion and stain resistance. Work the grout diagonally into the joints with a rubber float, strike off the excess, then sponge clean once the grout firms and buff away residual haze. Initial set is about 24 hours, showers can get wet after 3 days, sealing is possible after 3 days and full cure takes 7 days.Important notesAllow roughly 15% wastage when estimating coverage from tile size, joint width and depth. Keep mixing water consistent between batches for uniform colour.Specifications Joint width 1 - 8mm Coverage guide Approx. 0.55kg/m² for 200 x 200 x 8mm tiles at 3mm joints Tile types Ceramic, porcelain, marble, granite, mosaics Location Walls and floors, indoor and outdoor SafetyContains cement - wet grout is alkaline and can irritate skin and eyes. Wear gloves and safety glasses, avoid dust when mixing, and wash hands after use. Keep out of reach of children and consult the Safety Data Sheet.
$41.03
Dunlop Universal Tile Adhesive is the do-almost-anything adhesive in the Dunlop Trade (ARDEX Australia) range – a high performance, multipurpose wall and floor tile adhesive with excellent workability and flexibility. Its non-slumping formula keeps wall tiles in position while its C2TES1 classification delivers extended open time, slip resistance and a deformable, high-strength bond for demanding applications.Where to use itOne of the most versatile adhesives available: suitable for indoor and outdoor walls and floors, and even swimming pools. It fixes ceramic, porcelain, natural stone (excluding moisture sensitive stone), mosaics and fully vitrified tiles over compressed fibre-cement sheet floors, concrete floors, fibre-cement sheet walls, Dunlop Undertile Waterproofing, plasterboard and render.How to useMix with clean water to a smooth, creamy consistency and allow to stand briefly before a final remix. Apply to a clean, dry, sound substrate with a 6mm notched trowel on walls or a 10mm notched trowel on floors. Press tiles firmly home with a twisting action, ensuring good adhesive transfer to the tile back – especially important outdoors and in pools where full contact is required. Grout after approximately 24 hours at 23°C and 50% relative humidity.Important notesNot suitable for moisture sensitive natural stone. For pool installations, allow the full recommended cure before filling. The product exceeds ISO 13007 requirements.Specifications Size 20kg bag Colour White Coverage 11m² per 20kg (6mm trowel); 7m² per 20kg (10mm trowel) Tile types Ceramic, porcelain, non-sensitive stone, mosaics, fully vitrified Substrates Concrete, compressed FC floors, FC walls, waterproofing, plasterboard, render Classification C2TES1 tile adhesive; exceeds ISO 13007 SafetyContains cement. Avoid breathing dust and avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection while mixing and applying, and work in a well-ventilated area. Refer to the safety data sheet before use.
$59.68
Dunlop Trade Resaflex is a multipurpose, rubber modified tile adhesive from Dunlop Trade (ARDEX Australia), trusted by professional tilers for decades. Its rubber modified cement formulation delivers a strong yet flexible bond that tolerates normal building movement, and its C2S1 classification confirms improved adhesion and deformability. One bag covers a wide range of everyday tiling jobs, which is exactly why it has earned its multipurpose name.Where to use itSuitable for indoor and outdoor walls and floors. Use it to fix ceramic tiles, fully vitrified tiles, mosaics, porcelain and natural stone (excluding moisture sensitive stone) over compressed fibre-cement sheet floors, concrete floors, fibre-cement sheet walls, Dunlop Undertile Waterproofing, plasterboard and render. It can also be used over Dunlop Waterproofing and green screed, making it well suited to bathrooms and new-build wet areas.How to useMix the powder with clean water to a smooth, lump-free paste. Spread onto a clean, dry, sound substrate with a 6-8mm notched trowel for tiles up to 250 x 250mm, or a 10-12mm notched trowel for larger tiles. Bed each tile with a firm twisting action to achieve full contact, and lift a tile occasionally to check coverage. Allow the adhesive to cure before grouting.Important notesNot suitable for moisture sensitive natural stone. Only mix what can be used within the working time and never re-temper stiffened adhesive with extra water.Specifications Size 20kg bag Colour Grey Coverage 0.65m²/kg (6-8mm trowel); 0.4-0.5m²/kg (10-12mm trowel) Tile types Ceramic, vitrified, mosaics, porcelain, non-sensitive natural stone Substrates Concrete, compressed FC floors, FC walls, waterproofing, plasterboard, render Classification C2S1 rubber modified tile adhesive SafetyContains cement. Avoid breathing dust, wear protective gloves, clothing and eye protection, and mix in a well-ventilated area. Wash skin after handling and refer to the safety data sheet before use.
$53.15
Dunlop Tiler's Mastic is a premium non-slump tile adhesive for walls and floors from Dunlop Trade (ARDEX Australia). Built for the demands of modern tiling, its high-grab, non-slump formula is ideal for today's large format tiles, holding them exactly where you place them on walls while still spreading smoothly and easily on floors. As a C2TES1 classified adhesive it offers extended open time, slip resistance and deformability for a strong, flexible bond.Where to use itSuitable for indoor and outdoor walls and floors, including wet areas over Dunlop Waterproofing. It fixes ceramic, porcelain, non-moisture sensitive natural stone, fully vitrified, mosaic and translucent tiles over cement render, compressed fibre-cement sheet (floors), concrete, Dunlop Undertile Waterproofing, existing ceramic tiles, ceramic tile underlay, fibre-cement sheet (walls) and plasterboard.How to useMix the powder with clean water to a smooth, creamy paste. Trowel onto a clean, dry, sound substrate with a 6 x 6 x 6mm notched trowel for walls or a 10 x 10 x 10mm notched trowel for floors and large tiles. Bed tiles with a firm twisting action, checking contact coverage regularly. Grout after approximately 24 hours.Important notesNot suitable for moisture sensitive natural stone. Ensure substrates are properly prepared and primed where required, and avoid tiling in extreme temperatures.Specifications Size 20kg bag Colour White Coverage 10m² with 6mm notched trowel; 6m² with 10mm notched trowel Tile types Ceramic, porcelain, non-sensitive stone, vitrified, mosaics, translucent Substrates Render, concrete, compressed FC sheet, waterproofing, existing tiles, plasterboard Classification C2TES1 tile adhesive SafetyContains cement – avoid breathing dust and avoid skin and eye contact. Wear protective gloves, clothing and eye protection, and mix in a well-ventilated area. Consult the safety data sheet before use.
$40.28
You have seen 48 out of 84 products
Powder or premixed mineral-based adhesives, grouts and repair mortars for masonry, tile and concrete. Apply by trowel; match notch size, water ratio and open time to the substrate. Consider compressive strength and flexibility requirements. Use filters to refine by set speed and application method. Always review the product page and TDS/SDS.
