Tin

PC-11® thrives in wet environments. It is resistant to water whether it is fresh or salt. Thick consistency like PC-7® and long open time (30 min). Work horizontal or vertical, indoor or outdoor. Wet, dry or under water. Whether you are working on an area where you just can’t remove water and moisture or you want the white colour for your repair, PC-11® is your choice. Choose PC-11® for ceramic repairs, pools and spas, fibreglass boats, tubs and sinks, stock tanks and thousands of other repairs. It has excellent adhesive properties bonding metals, fibreglass, wood, tile and some plastics such as ABS and rigid PVC. Ample open time allows tooling or positioning in order to tackle larger and challenging jobs. When mixed, the epoxy, part A (white) and the hardener part B (lt. blue) react to form a bond of tremendous strength and flexibility. The PC-11® formulation is slow curing, but slow can be a good thing especially for large tasks. WORKING TIME: 30 MINUTES CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE) PC-11® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Not quite as thick as peanut butter. Here are just a few specific uses (there are hundreds of other uses): Reattach missing swimming pool tiles. Patch a hole in a fibreglass canoe or the fibreglass keel of a fishing boat. Repair cracked or damage swimming pool or hot tub skimmer. Waterproof and Seal cracked fibreglass. Seal screw holes to hatch lids or seating. Attach fish locators to transom. Repair stock tanks. Repair broken refrigerator door shelf fixtures. Repair broken pottery. Repair shower basin or antique bath tub. Seal leaking air conditioner drip pan. Seal underground conduit. How to prepare a surface for bonding with PC-11® Epoxy Paste Remove contaminants such as dust, dirt, oil, barnacles and grime with a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. For a wet or underwater surface; clean contaminants as best as you can. Solvents will not help you in this situation. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-11® Epoxy Paste application Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-11® cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. Can PC-11® be used in Aquariums? There is the potential for PC-11® part A and part B to harm sea life but properly measured and mixed PC-11® has been used safely in fresh and saltwater aquariums. It is important that part A and B are thoroughly and completely mixed. What plastics does PC-11® stick to? PC-11® has good adhesion to Rigid PVC and CPVC, polyester and fiberglass, polyurethane, ABS and Bakelite. What plastics does PC-11® not stick to? PC-11® does not stick to polyethylene, polypropylene, HDPE, polystyrene, nylon, acrylic, Teflon, and polycarbonate. What rubbers does PC-11® stick to? PC-11® sticks to SBR, Buna, and polyurethane rubbers and does not stick to EPDM, vinyl and neoprene rubbers. What temperatures can PC-11® be applied? PC-11® cures very slowly at temperatures below 50°F (10°C). At or below freezing temperatures the PC-11® will stop curing. In hot conditions, above 95°F (35°C), PC-11® will cure rapidly reducing the working or application time. Can gel coat be applied to PC-11®? Gel coat will not cure properly in direct contact with PC-11®. It is important that repairs made with PC-11® be sealed with a suitable primer/sealer before applying a gel coat. Can PC-11® be painted? Yes. It is good practice to apply a premium stain sealing primer to repairs made with PC-11® prior to the finish coat. Will PC-11® yellow in direct sunlight? Yes, PC-11® yellows in direct sunlight. PC-11® resists ultraviolet light but will still gradually change colour. Prime and paint if the colour is important. Can PC-11® be thinned with solvent? PC-11® does not contain solvents. Acetone and denatured alcohol (ethanol) are compatible but will extend the cure time and decrease the hardness. Other solvents such as mineral spirits, paint thinner and turpentine are not compatible. PC-11® is a simple one to one mix, but how accurately does the measurement need to be? The volume of part A to part B should be close to equal. A slight excess of part A is preferable to an excess of part B. Excess of part B will not accelerate the curing and it may make it softer.

Read more less

Glitz Beeswax Polish for Timber and Furniture Shine 200g Bring tired timber back to life with a rich beeswax polish that nourishes, protects, and leaves a warm, natural glow. Perfect for refreshing furniture finishes and helping repel dust with a silky, low sheen. Why choose this polish Deep conditioning to help replenish dry timber surfaces. Natural wax glow for a classic hand-rubbed finish without a greasy residue. Dust resistant finish that helps surfaces stay cleaner for longer. Easy to use wipe on, let cure briefly, then buff to shine. Versatile suitable for most sealed and previously waxed wood furniture. Ideal for Dining tables, sideboards, desks, chairs, and timber trims Antique and vintage furniture restoration touch ups Timber accessories and decorative pieces Not suitable for Unsealed raw wood where an oil or sealer is required first High traffic floors or benchtops that need hard wearing coatings Exterior timber exposed to weather How to use Clean the surface to remove dust and light grime. Ensure the area is dry. Apply a small amount of polish with a soft lint free cloth using circular motions. Set allow 5 to 10 minutes for the wax to haze lightly. Buff with a clean cloth until the desired sheen appears. Repeat light coats on very dry timber for an even, richer finish. Pro tips Test in an inconspicuous spot to confirm compatibility and sheen level. Less is more. Thin coats deliver a smoother, streak free result. Maintain with a quick rebuff or a very light reapplication every few months. Compatibility Suitable on sealed, varnished, lacquered, shellac, and previously waxed timber Always avoid application on wet or recently oiled surfaces Ingredients overview Beeswax blend with conditioning waxes in a cleaning and polishing carrier. Product details Brand Glitz Product Beeswax Polish for Timber and Furniture Shine Pack size 200g Finish Low sheen, natural glow Coverage Varies by timber and porosity. A little goes a long way. Use Interior Clean up Wipe cloths with a small amount of mild detergent, then rinse and air dry Storage Keep tightly closed in a cool, dry place away from direct sunlight Safety Use in a well ventilated area. Avoid contact with eyes and prolonged skin contact. Keep out of reach of children and pets. Frequently asked questions Will it darken the timber? Wax can slightly enrich color and grain. Always spot test first. How often should I reapply? For most furniture every 2 to 4 months is sufficient. High use items may benefit from more frequent light applications. Can I use it over raw wood? For best durability seal or oil raw wood before waxing. Good to know Apply thin, even coats for best clarity and feel. Buff with a clean microfiber cloth to elevate the final sheen.

Read more less

Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.

Read more less

Polishes internal furniture & joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items. Also suitable for sealing and polishing slate, terracotta and stucco Coverage: Up to 40 m2 Number of Coats: 2 Recoat: 24hrs Sheen Level: Pale Satin

Read more less

Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.

Read more less

Selleys N Mastic is a non-hardening, waterproof sealing putty designed for a wide range of applications where long-lasting flexibility is crucial. Ideal for sealing joints, gaps around windows, and roofing, it ensures that structures remain protected from water ingress. The unique formula remains pliable, making it perfect for environments where movement and expansion are expected. Whether you're sealing an outdoor roof gutter, securing window frames, or filling gaps in an air conditioning system, Selleys N Mastic provides a professional-grade finish with no cracking or crumbling. The product is also suitable for metal, glass, concrete, and brick, making it a versatile solution for residential, commercial, and industrial projects. N-Mastic is a non-skinning polybutene-based compound. It will remain permanently soft and paste-like. Uses N-Mastic is suitable for sealing concealed lap joints between plastics, metals, timber, glass, masonry, and expanded foam panels. It may be used in the installation of cool rooms, prefabricated construction and gasket sealed windscreens to exclude draughts and water penetration through joints in materials. Technical Features Non-hardening – remains permanently flexible to provide a lasting seal Good adhesion – adheres well to most substrates Moisture resistance – provides an excellent barrier to moisture vapour Microbe resistance – resists microbial attack Low shrinkage – avoids the risk of sealant pulling away from joint surfaces Wide service temperatures – withstands –40oC to +80oC service conditions Application Tips Due to the non-skinning, non-hardening nature of the sealant, N-Mastic should not be used in exposed joints where dirt pick-up or hand contact can be a problem. As N-Mastic is not elastomeric, it should not be used in areas subject to considerable dynamic stress. Although N-Mastic is resistant to static pressures, a curing sealant is recommended where this is a critical factor. N-Mastic is not recommended for sealing lap joints in mobile homes, truck bodies, etc., as significant vibration and flexing occur during travel. Technical Details and Performance Indicative information only, not to be used for setting specifications. Colour Off White Specific Gravity 1.4g/mL Consistency Non-sag Slump (MIL-S-8802, @ 32oC ) 2.5mm maximum Viscosity (Brookfield HAF 7/2 @ 25oC ) 10,000 – 14,000 Poise Flash Point 85oC Storage Life (25oC ) Indefinite Packaging Plastic cartridge (410g) Performance Properties Shrinkage (% maximum) 5 Service Temperature –40oC to +80oC Life Expectancy Up to 20 years Clean Up Sealant may be removed with a cloth dampened with kerosene or mineral spirits

Read more less

Features Resists intense heat Sets hard Water clean up Where can this product be used? Repairing bricks in fireplaces and chimneys Sealing flues in pot-belly stoves Filling cracks in ironworks and bricks  What materials is this product suitable for? Brick Metal Concrete How to Use: Remove all dust, grease and loose debris before applying material. Dampen the cavities on porous surfaces for better adhesion. Apply Fireproof Cement firmly into holes and cracks with a damp knife or spatula. Allow Fireproof Cement to dry a minimum of 48 hours before exposure to heat. If Fireproof Cement is stiff slacken with a little water. Limitations: Fireproof Cement is not an adhesive - it is a filling compound. Not recommended for external use e.g. BBQ's, incinerators etc. Fireproof Cement is not suitable for use in kilns. Fireproof Cement is not recommended for moving joints such as expansion joints as it sets rigidly Hardened material cannot be resoftened with water.

Read more less

A blend of nut and citrus oils specially formulated to create a drying oil to maintain and rejuvenate wooden items that come into regular contact with food or water which can cause the timber to swell and dry out. Simple wipe on and wipe off application to make timber look & feel nourished.     Maintain wood items that come in contact with food & water. Ideal for wooden chopping boards, serving bowls and utensils.   250mL     Simple wipe on and wipe off with a rag

Read more less

Parfix Fast Grip is a solvent-based, brush-on contact adhesive made for kitchen and bathroom jobs where heat and moisture are a concern, supplied here in a 1L pack. It grips firmly as soon as the two coated surfaces meet, so it suits laminates, veneers, trims and similar sheet work where you want a strong bond without long clamping.About the formulaFast Grip is a polychloroprene rubber contact adhesive in a tan-coloured liquid. The solvent carrier makes the product resistant to heat, water and many solvents once cured. It does not dry clear, so keep it off visible faces and wipe back any squeeze-out or drips before they dry. The product is applied with a brush and is classed by the manufacturer as a flammable liquid (see Safety below).Where to use itIndoors: kitchen and bathroom work such as laminate and veneer fixing, trims and panels, plus general repairs where a heat and moisture resistant bond is needed.Outdoors: the supplied product information does not confirm exterior use, so check the pack or contact the manufacturer before using it on exposed work.The manufacturer's safety data lists wood, hardboard, cork, rubber, leather, canvas, laminated plastics and metals as materials it is made to bond. Test a small hidden area first, especially on foam, vinyl or other plastics, because solvents can soften or mark some of them.How to use itMake sure all surfaces are clean, dry and free of dust, oil and grease. Stir or shake the contents if needed. Brush a thin, even coat onto both surfaces and let the solvent flash off until the film is ready for bonding, following the directions on the pack. Align the pieces carefully before they touch, because a contact bond grips on first contact and there is little chance to reposition. Press the surfaces together firmly, working across the whole area. A roller or hand pressure over the full surface helps. Reseal the tin tightly after use.Important notesParfix Fast Grip is not a clear-drying glue. Do not apply it near naked flames, heaters or other ignition sources, and work only in a well-ventilated area. Always check the label for open time, cure time and clean-up directions, as these are not confirmed in our supplied data. For best results, store the tin sealed and away from heat.Specifications Brand Parfix Product Fast Grip Contact Adhesive Size 1L Colour Tan Base Solvent-based polychloroprene rubber Application Brush Dries clear No Resistance Heat, water and solvent resistant Bond Immediate grip on contact SafetyKeep away from heat, sparks and flames. Vapours may cause drowsiness or dizziness, and inhaling them can depress the central nervous system. Use only in a well-ventilated area or outdoors. Wear nitrile gloves, eye protection and suitable protective clothing. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Selleys Kwik Grip Horizontal is a flexible, solvent-based contact adhesive that grips the moment two coated surfaces meet, supplied here in a 500ml can for larger bonding jobs. It suits both porous and non-porous materials and has a thicker body that is easy to spread on flat work, making it a handy choice for laminates, rubber, leather, cork and timber around the home, workshop or job site.About the formulaThis is a polychloroprene contact adhesive in a solvent carrier, light amber in colour. The thicker consistency helps it spread without running or stringing, and it is designed for bonding without clamping once the surfaces are joined. The cured bond is flexible, heat resistant up to 130°C, water resistant and holds up against dilute acids and alkalis.Where to use itIndoors: fixing laminate sheet to benchtops and cabinetry, bonding cork, felt and rubber, repairing leather and canvas items, and general workshop or furniture jobs.Outdoors: repairing tents, car covers and other outdoor canvas equipment, and refitting rubber seals, as the cured bond is rated for exterior use.Suitable materials include laminated plastics (such as Laminex and Formica), rubber, leather, canvas, felt, timber, hardboard and compressed board, cork, metals including aluminium, and fibre cement sheeting. Test any other plastic on an offcut first.How to use it Make sure both surfaces are clean, dry and free of dust, grease and loose material. Apply an even coat to both surfaces using a brush or spreader. Leave the surfaces apart until the adhesive is touch dry. This takes about 20 minutes and should not exceed 40 minutes. Line the surfaces up carefully before they meet, using spacers such as dowels on large panels, because the bond grabs immediately on contact. Press the surfaces together firmly, working from one edge, then roll or press with a padded block to bring the whole area into contact. For small porous areas, you can apply to one surface only, join while wet and clamp until dry. Wipe away wet excess with mineral turpentine. Important notesFull bond strength develops in about 24 hours. Do not use on polyethylene or polypropylene. Some plastics, including vinyl sheeting and polystyrene, can be attacked by solvent-based contact adhesives, so test first. Warped or curved surfaces may need clamping. Use only in a well-ventilated area and keep away from heat, sparks and open flames.Specifications Brand Selleys Product Kwik Grip Horizontal Contact Adhesive Pack 500ml can Colour Light amber Base Solvent-based polychloroprene Application Brush or spreader, applied to both surfaces Open time Touch dry in about 20 minutes (maximum 40 minutes) Full strength About 24 hours Heat resistance Up to 130°C Use Interior and exterior SafetyWear protective gloves, protective clothing and eye protection, and use a suitable respirator if there is an inhalation risk. Use outdoors or in a well-ventilated area, keep away from ignition sources and do not smoke. Keep the container tightly closed and store it in a cool, well-ventilated place away from heat. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Selleys Plastic Wood is a fast-setting, solvent-based wood filling cement for repairing holes, dents and chips in interior timber, supplied here in a 230g maple-coloured tin. It is a simple fix for furniture, skirting, architraves and other indoor joinery, and once set it can be worked much like the timber around it.About the formulaA solvent-based paste containing natural wood fibres, finished in a maple (tan) colour. It dries quickly to a hard finish that holds up to sanding, nailing and planing. Once dry it can be stained, varnished, painted or lacquered, so the repair can be finished in the same way as the surrounding wood. It is a rigid filler, so it is not designed for joints that move.Where to use itIndoors: filling nail holes, dents, chips and small cracks in furniture, doors, window frames, skirting boards, architraves and other interior woodwork.Outdoors: not recommended. The manufacturer rates this product for interior use only.Suitable materials include natural timber and wood veneer.How to use itStir the product thoroughly before use. Make sure the surface is clean, dry and free of loose material. Press the filler in with a putty knife and slightly overfill deeper holes so there is room to sand back flush. Do not fill deeper than 6mm in a single application. Let it dry fully before sanding, staining, painting or lacquering. Wipe the putty knife clean with methylated spirits. Press the lid on firmly after use and store the tin somewhere cool.Important notesNot suitable for exterior use. Not recommended where structural movement may occur, so use a flexible product for joints and gaps between surfaces. Work in a well-ventilated area. Colour is maple only, so test a small area first if you need to match a different timber tone, or plan to stain or paint over the repair.Specifications Brand Selleys Product Plastic Wood Filler Cement Size 230g tin Colour Maple Base Solvent-based, with natural wood fibres Application Putty knife Maximum fill depth 6mm per application Set speed Fast setting Clean up Methylated spirits Use Interior only SafetyThis is a highly flammable solvent-based product. Keep it away from heat, sparks, flames and other ignition sources, and avoid static discharge. It can irritate skin and eyes, and the vapours may cause drowsiness or dizziness. Use only in a well-ventilated area and avoid breathing vapours. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Deks Duo Bond is a two-part epoxy jointing putty made for plumbers, pool technicians and serious DIYers, supplied here as a 1 litre kit with a 500ml tin of base and a 500ml tin of hardener. Once mixed, it forms a thick, putty-like compound that bonds and fills large voids, and it sets hard like concrete. It is also approved for drinking water use in Australia, so it suits both water infrastructure and everyday repairs.About the formulaA two-part epoxy system built around an epoxy resin base and a separate hardener. The mixed material has a heavy, putty-like body that holds its shape, which makes it well suited to jointing, patching and filling work where a runny adhesive would not stay put. It can be applied above water or while submerged. The product carries AS/NZS 4020 drinking water and WaterMark (WMTS-014) certification.Where to use itIndoors: jointing cast iron soil, waste and ventilation pipes and fittings, and general repairs to concrete, metal and steel.Outdoors: swimming pool crack repairs, concrete and masonry repairs, and fixing metal fissures and steel fractures.Suitable materials include cast iron, steel and other metals, and concrete. The manufacturer describes it as suitable for many material types, provided surfaces are clean, dry and free of oil and grease. Test on an offcut first if you are unsure about a particular surface.How to use itClean the repair area so it is free of oil, grease, loose material and dirt. Mix the base and hardener thoroughly until the colour is even, following the mixing instructions supplied with the pack. Press the mixed putty firmly into the joint, crack or void and tool it to shape. Wear gloves and eye protection while mixing and applying. Mix only as much as you can use before it starts to set.Important notesThe compound is stiff and takes some effort to mix by hand, so allow time for thorough mixing. Working time and full cure time depend on temperature and batch size, so check the technical data sheet for the exact figures before starting a critical repair. Both parts must be mixed together before use, and uncured material should be kept out of drains and waterways.Specifications Brand Deks Product Duo Bond Two-Part Epoxy Jointing Putty Compound (model 2046) Pack 1L kit: 1 x 500ml base + 1 x 500ml hardener Colour Grey Chemistry Two-part epoxy (base and hardener) Consistency Putty Application Mixed by hand and applied as a putty Certifications AS/NZS 4020 drinking water, WaterMark WMTS-014 Use Interior and exterior, above water or submerged SafetyThe base component contains bisphenol A epoxy resin and is classed as environmentally hazardous, so keep it out of drains, soil and waterways. Avoid skin and eye contact, wear chemical-resistant gloves and eye protection, and work in a well-ventilated area. If product contacts skin, wash with soap and water. Store the tins sealed, in a cool, dry place and out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Fastfix Wet Shield is a fibre-reinforced, one-coat roof and gutter repair membrane that can be applied straight onto wet or damp surfaces, supplied here in a 2.5kg tin in grey. It is made for emergency leak repairs, so you can seal a leaking roof without waiting for the rain to stop, and it also suits planned maintenance work in dry weather.About the formulaA resin-based, solvent-based compound with reinforcing fibres that interlace to bridge small gaps and cracks. The manufacturer describes it as formulated from lightfast acrylic polymers, which helps it withstand UV exposure for longer than traditional bitumen coatings. It is waterproof the moment it goes on, so rain straight after application will not wash it off. It cures to a smooth, seamless, flexible membrane that resists algae and fungal growth. On sound, non-porous surfaces no primer is needed.Where to use itIndoors: not recommended for internal use.Outdoors: roofing and gutter repairs, including tile and metal roofs, valleys, gutters, flashings, fascias, downpipes and cappings, plus concrete and brickwork. Areas that collect ponding water are covered by the one-coat system, provided the recommended minimum finished fall is achieved.Suitable materials include concrete, fibre cement, roof tiles, slate, metal roofing, guttering, brickwork, lead flashing, uPVC, asphalt and bituminous roof coatings. Non-ferrous metals such as aluminium, copper and previously painted non-ferrous metals should be primed with a suitable etch primer first. If you are unsure about a surface, run a small adhesion test before committing to the whole job.How to use itEmergency wet repairs: no preparation is needed. Brush a thick coat over the affected area to create an immediate barrier against water ingress.Planned dry-weather work: clear moss, lichen and debris by brushing, scraping or pressure washing. Let the surface dry, remove any oil or grease with white spirit, and let it dry again. Then apply the product generously with a brush, roller or squeegee in one coat.Seal air-conditioning vents for at least 24 hours during and after application. Clean tools with white spirit or methylated spirits.Important notes Not recommended for wooden surfaces, tanking, fishponds or internal use. Not designed for areas with heavy foot traffic. Allow up to 6 to 7 days to dry, depending on temperature and coat thickness. It may stay soft for longer in some climates, which does not affect its waterproofing. Manufacturer information recommends applying between 5°C and 25°C and a minimum finished fall of 1:80. Discolouration may occur over new asphalt, tar or bitumen. Shelf life is up to 2 years in an unopened container stored correctly. If a primer is needed on a particular substrate, check with the manufacturer for suitable options. Specifications Brand Fastfix Product Wet Shield One Coat Instant Waterproofing Pack 2.5kg tin Colour Grey Base Resin based, fibre reinforced, solvent based Application Brush, roller or squeegee, one coat Coverage 1kg to 2kg per m2, depending on substrate Drying time Up to 6 to 7 days, depending on temperature and thickness Application temperature 5°C to 25°C Minimum finished fall 1:80 Flash point 40°C (per SDS) Clean up White spirit or methylated spirits Use Exterior roofing and gutters SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Avoid breathing vapours, use in a well-ventilated area, and wear protective clothing, eye protection and face protection. For eye contact, rinse with plenty of water for 15 minutes holding the eyelids open. For skin contact, wash with soap and water. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Crommelin AquaBlock Waterproof Primer Undercoat is a water-based primer, sealer and stain-blocking undercoat made for damp-prone areas of the home, supplied here in a 1L tin that suits bathroom, laundry and small repaint jobs. It builds a water-resistant, paintable base over bare and previously painted surfaces, so water-based topcoats can go on over an even, sealed surface.About the formulaAquaBlock is a high-cover, low-odour wall primer with a flat finish. Crommelin positions it as a sealer, primer, undercoat and stain blocker in one product. It grips both porous and non-porous surfaces, seals off stains and gives topcoats a uniform surface to bond to. The manufacturer also describes it as a mould-resistant undercoat, which makes it a sensible choice for bathrooms, kitchens and laundries. It is designed to be overcoated with water-based paints and cleans up with water.Where to use itIndoors: walls and ceilings in bathrooms, kitchens, laundries and hallways, especially where steam, condensation or past moisture damage has caused staining or peeling.Outdoors: eaves and exterior walls and other masonry or timber surfaces that will be topcoated with a water-based paint.Suitable surfaces include plasterboard, brick, concrete and concrete blocks, cement sheeting, render, masonry, timber, plywood, particleboard and suitably prepared steel.How to use itMake sure the surface is clean, dry, sound and free of dust, grease, loose paint and mould before you start. Stir the product well, then apply it with a brush or roller. Check the label for the recommended number of coats and the spread rate for your surface. Apply only when the temperature is at least 5°C. The retailer lists a recoat time of about 120 minutes. Clean brushes, rollers and tools with water straight after use, before the product dries.Important notesThis product is not tintable and is supplied in white only. Crommelin advises it is not suitable over white set plaster and should not be used as a base before tiling. It is a primer and undercoat, not a decorative finish, so topcoat it with a water-based paint. Surface and weather conditions affect drying and performance, so test a small area first on unusual or heavily stained substrates. Check the label for full application details.Specifications Brand Crommelin Product AquaBlock Waterproof Primer Undercoat Size 1L tin Colour White (not tintable) Finish Flat Base Water-based Application Brush or roller Coverage 12 to 14 m² per litre (retailer figure; check the label) Recoat time About 120 minutes Minimum application temperature 5°C Clean up Water Topcoat Water-based paints Use Interior and exterior SafetyEven so, avoid contact with skin and eyes, wear suitable protective clothing and gloves, and use it in a well-ventilated area. Keep the lid on the tin when not in use, store it in a cool, dry place and protect it from freezing. Keep it out of reach of children. Do not tip leftover product or wash water into drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Dunlop Gripper Fast Tile Adhesive 500 ml Overview Dunlop Gripper Fast Tile Adhesive 500 ml is a high quality multipurpose adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials common building materials ceramics wood metals some plastics stone Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Apply between 10°C and 30°C. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Cure time varies with product and conditions. Allow adequate time before loading or finishing. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean uncured product with a suitable solvent or water as applicable. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. Do not ingest. Refer to the Safety Data Sheet (SDS) for full details. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

Read more less