🌍 Worldwide Shipping Available | Fast & Secure Delivery ✈️

Dunlop

36 products

  • Packshot of Dunlop Ready-To-Go Vinyl Flooring Spray Adhesive 454g

    Dunlop Dunlop Ready-To-Go Vinyl Flooring Spray Adhesive 454g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Ready-To-Go Vinyl Flooring Spray Adhesive is a fast and tidy spray-on adhesive for installing vinyl sheet, vinyl tiles, and vinyl planks with vinyl backing over concrete, underlayment grade plywood, metal, and fibreglass. It delivers an even spray pattern, strong bond, and immediate traffic readiness once rolled. Why choose this adhesive Quick, clean spray application that saves time High initial grab for reliable placement Dry to touch in about 10 to 40 minutes Up to 3 hours open time once tacky Ready for immediate foot traffic after rolling Heat weld flooring 1 hour after installation Suitable with underfloor heating systems Water based acrylic blend with very low odour Suitable substrates Concrete, underlayment grade plywood, metal, and fibreglass. Use on vinyl-backed sheet, tiles, and planks. Not suitable for Cushion-backed flooring products. Surface preparation Ensure the substrate is flat, dry, and free from dust, oil, paint, old adhesive, wax, curing compounds, sealers, and hardeners. Lightly damp-mop concrete to remove fine dust before application. Correct surface imperfections before installation to avoid telegraphing. How to use Ventilate and mask the area to protect adjacent surfaces from overspray. Shake the can well and remove the blue safety tab. Hold the can upright 50 to 76 cm above the substrate and spray in smooth, even passes to achieve a uniform frosted look. Avoid heavy patches and overspray. Lightly re-spray missed areas if needed. Allow to dry until no adhesive transfers to the fingertips. Lay the vinyl and roll firmly within 1 hour using a suitable heavy roller to ensure full contact. The floor is ready for immediate use once rolled. Heat welding can commence after 1 hour. Key technical data Chemical type: water based acrylic blend Dry to touch: approximately 10 to 40 minutes Open time after tack: up to 3 hours Traffic allowance: immediate after rolling Underfloor heating: compatible Appearance when sprayed: milky white frost Storage and safety Store between 10°C and 50°C. Avoid freezing and direct sunlight. Pressurised dispenser. Do not pierce or burn the can, even when empty. Use in a well ventilated area and avoid contact with eyes and skin. Tip: Wipe any overspray from adjacent surfaces with a damp cloth before it dries.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $48.36

  • Packshot of Dunlop Tile-All Plus Premixed Tile Adhesive 310ml

    Dunlop Dunlop Tile-All Plus Premixed Tile Adhesive 310ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Tile-All Plus Premixed Tile Adhesive 310ml Tile-All Plus is a single component, silane modified polymer adhesive and neutral curing sealant. It offers high initial tack, strong bonding and excellent flexibility. Use it for fast, reliable repairs in showers, kitchens and bathrooms, for replacing tiles, fitting accessories and finishing joints. It can even be used for minor repairs underwater. Why you will like it High initial grab for confident positioning Flexible bond that resists movement and vibration Neutral cure for a low odour application experience Works as both an adhesive and a sealant Paintable after drying with most common paints (test first) Where to use it Showers, kitchens and bathrooms Replacing loose tiles and fitting trims or accessories Finishing expansion and connection joints Minor underwater fixes on suitable surfaces Suitable materials Glass, tiles, ceramics, timber, plastics, metals, concrete, wall panels, waterproofing membranes, aluminium, polystyrene foam, and glazed tiles. Always ensure surfaces are sound, clean and free from dust, oil, grease and coatings. Slightly damp substrates are acceptable. How to use Remove the aluminium seal at the base of the cartridge. Pierce the inner membrane, fit the nozzle and trim to the required bead size. Apply in stripes to the substrate or the item being fixed. Press parts together firmly within 7 to 10 minutes at 20°C, before skinning begins. For spot fixing, keep glue points 25 to 30 cm apart and confirm the item weight is appropriate. Avoid application below 5°C or above 35°C. Good to know Open time varies with temperature, humidity and substrate. Higher humidity shortens open time. If reusing, remove any skinned layer from the nozzle before the next application. Spills can be wiped away while wet with a clean cloth. Not recommended for chemical resistant applications. Cleanup and storage Clean excess while wet with a cloth. Shelf life is up to 12 months in unopened packaging stored in a cool, dry place at around 23°C and 50 percent relative humidity. Safety Use in a well ventilated area. Avoid skin and eye contact. If contact occurs, flush eyes with water for at least 15 minutes and seek medical advice. Wash skin with soap and water. If inhalation discomfort occurs, move to fresh air. If swallowed, drink water in small portions and seek medical advice. Keep out of reach of children.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $27.98

  • Packshot of Dunlop Premixed Resaflex Wall & Floor Tile Adhesive 15kg

    Dunlop Dunlop Premixed Resaflex Wall & Floor Tile Adhesive 15kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Premixed Resaflex Tile Adhesive Ready to use, flexible and tough ceramic tile adhesive for dependable indoor tiling. Ideal for interior walls and fibre-cement sheet residential floors. No mixing required, spreads smoothly, and delivers a secure bond when applied at the correct bed thickness. Key Benefits Ready mixed convenience for faster start and less mess Flexible bond that helps accommodate minor movement Non-slump paste with excellent grab on vertical surfaces Suitable for common interior wall substrates and fibre-cement sheet floors Where To Use Walls: Interior applications on cement render, plasterboard, and fibre-cement sheet Floors: Residential fibre-cement sheet floors Tiles: Ceramic and similar porous tiles Surface Preparation Surfaces must be flat, clean, dry and firmly fixed. Remove dust, oil, grease and loose materials. Prime porous surfaces like cement render and fibre-cement sheet, and any base jointing compound on plasterboard, then allow to dry. Remove water based paints completely. If paint integrity is uncertain, roughen or remove. Application Use an appropriate notched trowel: as a guide 6 mm for walls, 10 mm for floors. Spread only as much as you can tile within open time, typically about 1 m² at a time. Ensure no skin has formed. Bed tiles into a 1.5 mm to 6 mm adhesive layer. Press and slide to ensure full contact. Clean excess adhesive from tile faces and joints before it sets. Coverage Guide Tile Size Notch Size Approx. Coverage per kg Up to 150 x 150 mm 4.5 mm ~0.7 m² 150 x 150 to 250 x 250 mm 6 to 8 mm ~0.5 m² 250 x 250 mm and over 10 to 12 mm ~0.3 m² Coverage varies with substrate condition, trowel angle and application technique. Drying and Grouting Typical set time is about 24 hours at 23°C and 50% relative humidity. Allow longer for dense tiles or cool and humid conditions. Grout after adhesive has set, usually after 24 hours. Movement Joints Provide joints around perimeters and at intervals consistent with good tiling practice, for example at about 5 m on floors and about 3.5 m along walls. Keep joints about 6 mm wide and free of adhesive and grout. Fill with a suitable flexible sealant. Limitations Not suitable over concrete where extended drying can occur. Not for areas subject to water immersion such as pools. Do not use for non-porous tiles over non-porous substrates or for moisture-sensitive stone. Final adhesive bed must be at least 1.5 mm and not more than 6 mm thick. Clean Up Clean tools and any fresh residue with water before the adhesive sets. Technical Data Type Single part viscous paste Colour Grey Bulk Density ~1.2 g/cm³ pH ~8.5 Slip 0 mm Extended Open Time ~1.2 MPa after 30 min Shear Bond Strength ~0.9 MPa Pack Sizes and Shelf Life Available in 1 kg, 4 kg, 10 kg and 20 kg pails Shelf life 12 months in unopened packaging stored in a dry place Good Practice Tips Use tile spacers for consistent joints and remove them before grouting. Prime porous substrates as directed for best results. Always follow movement joint requirements for long-term performance.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $79.80

  • Packshot of Dunlop FC Polyurethane Flexible Joint Sealant 300ml

    Dunlop Dunlop FC Polyurethane Flexible Joint Sealant 300ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop FC Joint Sealant Dunlop FC Joint Sealant is a premium, ultra flexible, moisture curing polyurethane sealant designed for jointing fibre cement, blueboard and compressed fibre cement sheets. The non slump formula handles joints up to 40 mm wide with a movement capability of plus or minus 25 percent. It is easy to apply, solvent free and isocyanate free. Colour: Grey. Why choose this sealant High flexibility for dynamic joints Non slump for clean, accurate beads on vertical and horizontal surfaces Solvent free and isocyanate free Paintable after curing Reliable performance supported by a 10 year guarantee Ideal uses Joints in fibre cement, blueboard and compressed fibre cement sheets Facade and cladding joints where movement is expected General building joints up to 40 mm width Compatible surfaces Adheres to most common construction substrates, including: Fibre cement sheets and blueboard Precast concrete panels, blockwork and bricks Sandstone and granite Fibreglass Plasterboard Technical details Movement capability ± 25% Joint width Up to 40 mm Skin time Approximately 35 minutes at 23°C and 50% RH Tack free time Approximately 1 hour at 23°C and 50% RH Cure rate About 2.5 mm per 24 hours at 23°C and 50% RH Application temperature 10°C to 35°C Clean up Warm water immediately after use Shelf life 12 months unopened, stored cool and dry Finish Paintable when dry. Can be overcoated with paint or texture coats. Colour Grey Surface preparation Ensure surfaces are clean and dry, free of dust, oil, grease, salt, mould, release agents and any contaminants that may affect adhesion. Mask adjacent areas to keep lines neat. Follow sheet fixing instructions from the board manufacturer. How to apply Cut the nozzle at a sharp angle slightly wider than the desired bead or joint width. Use a suitable backing rod where required to control depth. Aim for a joint depth equal to half the joint width. Gun the sealant into the joint and tool within 10 minutes using a round spatula to ensure full contact with the joint sides. Curing times increase in cold or humid conditions. Safety and handling Avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection. Ensure adequate ventilation during application. Keep out of reach of children. Refer to the product SDS for full safety guidance. Guarantee Backed by a 10 year guarantee when used as directed.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $21.58

  • Packshot of Dunlop Vinyl Adhesive 4L

    Dunlop Dunlop Vinyl Adhesive 4L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $84.98

  • Packshot of Dunlop Vinyl Adhesive 1L

    Dunlop Dunlop Vinyl Adhesive 1L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $27.85

  • Packshot of Dunlop Wall Tile Adhesive 15kg

    Dunlop Dunlop Wall Tile Adhesive 15kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Wall Tile Adhesive 15 kg OverviewDunlop Wall Tile Adhesive 15 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first.Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured.What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat.How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $79.61

  • Packshot of Dunlop Floor Tile Adhesive 4kg

    Dunlop Dunlop Floor Tile Adhesive 4kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Floor Tile Adhesive 4kg is a premium cement-based adhesive formulated for fixing a wide range of floor tiles, including ceramic, porcelain, mosaics, and natural stone. It provides strong bonding performance, easy application, and long-lasting durability for both indoor and outdoor projects. Key Features Ideal for floor installations in residential and commercial settings Suitable for concrete, cement screeds, compressed fibre-cement sheets, and existing tiles Strong adhesion with excellent workability and pot life of up to 2.5 hours Can be used indoors and outdoors for versatile tiling applications Grey colour finish for consistent, professional results Coverage Recommended trowel: 10 x 10 x 10 mm Approximate coverage: 0.4 m² per kg Typical total coverage: around 1.6 m² per 4 kg bag Mixing Instructions Use approximately 400 ml of clean water per 1 kg of powder. Add powder to water and mix to a thick, creamy consistency. Allow to stand for 5 minutes, then re-mix thoroughly before use. Do not add additional water once mixed. Application Apply with a suitable notched trowel ensuring full coverage under tiles. Spread only enough adhesive that can be tiled within the open time. Press and slide tiles at right angles to the notches for full contact. Do not exceed a bed thickness of 10 mm or less than 3 mm. Allow adhesive to set for approximately 24 hours before grouting. Limitations Not suitable for continuous water immersion such as pools or tanks Do not use over timber floors or non-absorbent substrates like metal Not recommended for substrates subject to movement or shrinkage Additional Information Clean tools with water immediately after use Shelf life: up to 12 months when stored sealed in a dry location Full traffic after 24 hours at 23°C and 50% relative humidity 10 Year Guarantee: Backed by Ardex Australia Pty Ltd against manufacturing defects when used according to the manufacturer’s directions. Based on Dunlop official technical data sheet. Always follow the latest installation guidelines and safety instructions.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $28.90

  • Packshot of Dunlop Multipurpose Carpet & Cork Adhesive 1L

    Dunlop Dunlop Multipurpose Carpet & Cork Adhesive 1L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    High strength, water based adhesive for carpet and cork Dunlop Multipurpose Carpet & Cork Adhesive is a water based, high strength adhesive designed for installing smooth or textured backed carpets and cork tiles. It delivers excellent wet grab and reliable bond on prepared subfloors. Suitable Surfaces Concrete Marine plywood Fibre cement sheet Key Features Water based and low odour High initial grab for reduced slippage Repositioning window up to 60 minutes Install immediately into wet adhesive for most carpets For cork or stiff backings, allow 10 to 15 minutes tack time before laying Coverage Approx. 2.5 m² per litre with a 3.2 mm V notch trowel Approx. 3.5 m² per litre with a 2.4 mm V notch trowel Application Ensure subfloor is dry, smooth, clean and protected from moisture. Prime highly porous concrete or timber before applying. Spread an even coat with the recommended V notch trowel. Lay carpet into the wet film. For cork or stiff backings, wait until the adhesive becomes tacky. Roll in both directions with a suitable drum roller to ensure full transfer. Set and Traffic Times No foot traffic for 24 hours Heavy traffic after 48 hours Avoid water and cleaning for 48 hours Clean Up Clean tools immediately with warm soapy water Remove dried residue with mineral turps Storage Shelf life up to 12 months in an unopened container stored at around 23°C. Good To Know Apply between 10°C and 30°C. Coverage varies with subfloor condition and trowel technique.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $29.41

  • Packshot of Dunlop Trade Resaflex Rapidset Tile Adhesive 15kg

    Dunlop Dunlop Trade Resaflex Rapidset Tile Adhesive 15kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Trade Resaflex Rapidset Tile Adhesive 15kg is a high quality, fast setting, rubber modified cement-based adhesive designed for rapid installation and early grouting. It delivers strong adhesion on walls and floors and is suitable for interior applications and exterior areas with satisfactory drainage. Key benefits Ready to grout in about 3 hours at 23°C and 50% RH Rubber modified formulation for strong bond and improved workability Classified C1FES1 Suitable bed thickness from 1.5 mm up to 10 mm Wall and floor use, interior and exterior (with correct falls and drainage) Suitable tiles Ceramic, porcelain, vitrified and mosaics Non moisture sensitive stone Suitable substrates Render, plasterboard, fibre cement sheet walls Compressed fibre cement sheet floors, concrete floors Existing tiles for interior applications Mixing and use Water addition: 5.5 L to 6.0 L per 15 kg bag Pot life: about 40 minutes at 23°C and 50% RH Trowel guidance: 6 x 6 x 6 mm on walls to achieve about 1.5 mm bed. 10 x 10 x 10 mm on floors to achieve about 2.5 mm bed Back buttering recommended for deeply keyed tiles and tiles larger than 450 mm on any edge Grouting: typically after about 3 hours at 23°C and 50% RH Coverage guide Trowel size Approximate coverage 6 mm About 0.6 m² per kg (about 9 m² per 15 kg) 10 mm About 0.4 m² per kg (about 6 m² per 15 kg) Movement joints Include movement joints in line with AS 3958 and around perimeters, penetrations and changes in direction. Fill with a suitable flexible sealant. Clean up Clean tools and residue with water while the adhesive is wet. Limitations Not suitable for continuous immersion such as swimming pools Not for moisture sensitive or translucent stone Do not tile directly over timber floors Safety Wear gloves, eye and face protection. Avoid breathing dust. In case of contact with eyes, rinse with water and seek medical advice. Keep out of reach of children. Technical details are based on manufacturer guidance at standard conditions. Actual times and coverage vary with temperature, humidity, tile and substrate.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $56.95

  • Packshot of Dunlop Pressure Sensitive Carpet Tile Adhesive 2L

    Dunlop Dunlop Pressure Sensitive Carpet Tile Adhesive 2L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Pressure Sensitive Carpet Tile Adhesive 2L Dunlop Carpet Tile Adhesive is a high strength, water based pressure sensitive adhesive designed for carpet tiles and double bonded underlay systems. It tacks off to a clear, dry-to-touch film that grips firmly yet allows tiles to be lifted and replaced for maintenance. Key features Pressure sensitive grab for secure hold and easy tile replacement Water based, low odour, easy to apply Suitable for smooth or textured tile backings and composition vinyl tiles Works with double bonded underlays in commercial fitouts Suitable substrates Concrete, plywood, fibre cement sheet, compressed fibre cement, and suitable underlay sheets. Subfloors must be dry, smooth, clean, and prepared to AS 1884 requirements including moisture testing. Coverage Approx. 10 m² per 2 L using a 1.6 mm V notched trowel Approx. 14 m² per 2 L using a long nap roller Drying and traffic Allow adhesive to become tacky and transparent before laying tiles. Typical tack off time is 2 to 4 hours depending on conditions. Heavy foot traffic after 24 hours Avoid wet cleaning or water exposure for 48 hours Application guide Prepare the subfloor. Prime very porous substrates if required. Treat rising damp or green concrete with a suitable moisture barrier. Apply adhesive evenly: Textured backs, composition vinyl tiles, and double bond underlays: 1.6 mm V notched trowel held at about 60 degrees Smooth backed tiles: long nap roller Wait until the film is tacky and clear with no transfer to fingertips. Early placement into wet adhesive will create a more permanent bond. Lay tiles, cut and reposition as required, then roll in both directions with a suitable roller to ensure full contact. Clean up Clean tools immediately with warm soapy water. Remove dried residue with mineral turps. Storage and shelf life 12 months in unopened packaging when stored in a cool, dry place at about 23°C and 50% RH. Good to know Do not apply below 15°C or above 30°C surface temperature. Not suitable for traditional carpet-to-underlay stretch-in installations. For double bond systems, follow the flooring manufacturer’s instructions. Safety Wear gloves and eye protection, ensure adequate ventilation, and keep out of reach of children. If eye contact occurs, rinse with water and seek medical advice if irritation persists.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $38.56

  • Packshot of Dunlop Trade Resaflex Rapidset Tile Adhesive 5kg

    Dunlop Dunlop Trade Resaflex Rapidset Tile Adhesive 5kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Trade Resaflex Rapidset Tile Adhesive 5 kg Overview Dunlop Trade Resaflex Rapidset Tile Adhesive 5 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $23.94

  • Packshot of Dunlop Mastic Multipurpose Tile Adhesive 5kg

    Dunlop Dunlop Mastic Multipurpose Tile Adhesive 5kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Mastic Multipurpose Tile Adhesive High performance, cementitious, non-slump tile adhesive designed for walls and floors. Combines the ease of a mastic with the strength of a cement-based adhesive for reliable results on small to large format tiles. Why choose it Non-slump hold for heavy and large format tiles Indoor and outdoor use on approved substrates Extended open time of up to 30 minutes to position tiles Bed thickness up to 10 mm White colour for use under light or translucent tiles Classification: C2TES1 Suitable tiles Ceramic, porcelain, mosaics, natural stone that is not moisture sensitive, fully vitrified and translucent tiles. Suitable substrates Render, screeds, concrete Plasterboard, fibre cement sheet walls, compressed fibre cement sheet floors Ceramic tile underlay Existing ceramic tiles indoors (properly prepared) Dunlop undertile waterproofing membranes Where it excels Walls needing strong initial grab Floors requiring reliable coverage and non-slump Large format and deeply keyed tiles where full contact is critical Coverage guide 6 mm notch (walls): about 0.5 m² per kg 10 mm notch (floors): about 0.3 m² per kg 5 kg bag: up to ~2 m² on walls or ~1.2 m² on floors 20 kg bag: up to ~10 m² on walls or ~6 m² on floors Set and grout times Allow approximately 24 hours at 23°C and 50% RH before grouting and light foot traffic. Dense tiles, cool weather or humid conditions may extend set time. Mixing 20 kg bag: 6 to 6.5 L of clean water 5 kg bag: 1.5 to 1.75 L of clean water Mix to a creamy consistency, stand for 5 minutes, then re-mix before use Application tips Follow AS 3958 best practice Spread only as much adhesive as can be tiled within the open time Press and slide tiles at right angles to the notches to achieve full contact Back-butter large or deeply keyed tiles for 100% coverage Remove squeeze-out from joints before setting Not suitable for Moisture sensitive natural stone Areas under permanent water immersion such as pools Timber, metal or any substrates subject to movement Application below 5°C Sizes 5 kg and 20 kg bags. Clean up Clean tools with water immediately after use. Safety Wear gloves and eye protection. Avoid inhaling dust. Refer to the product SDS and follow all safety directions.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $21.05

  • Packshot of Dunlop Roof Repair Waterproofing Adhesive 310ml

    Dunlop Dunlop Roof Repair Waterproofing Adhesive 310ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Roof Repair Waterproofing Adhesive 310ml Seal, stick and stop leaks on the spot. This highly flexible, silane modified adhesive and sealant bonds and seals even in wet conditions, making it a smart fix for urgent roof, gutter and pond repairs. Why you will love it Works in the wet and can be applied underwater for minor repairs Flexible waterproof seal for joints, cracks and patches Strong adhesive grab for quick spot fixes Paintable once cured to match surrounding surfaces Low mess clean up while wet Ideal surfaces Concrete, wall panels, timber, waterproofing membranes, ceramic tiles, aluminium, plastics, metal, polystyrene foam, glass and glazed tiles. Typical uses Emergency roof and gutter leak sealing Sealing laps, flashings and penetrations Pond edge and minor underwater touch ups General crack and joint sealing around the home Spot fixing where fast, reliable adhesion is needed Directions Prep: Ensure the surface is firm and free of dust, oil and loose residues. Slightly damp surfaces are acceptable. Load: Remove the aluminium seal, pierce the nozzle membrane, fit and trim the nozzle, then place the cartridge in a caulking gun. Apply as a sealant: Gun a continuous bead over the joint or crack and allow to cure. Apply as an adhesive: Gun bead lines or spots, then press parts together within 7 to 10 minutes at 23°C, before skinning starts. For spot fixing, keep glue points 25 to 30 cm apart. Clean up: Wipe away any excess while wet with a clean cloth. Good to know Application temperature: 5°C to 35°C Dry and cure times vary with substrate and climate. Higher humidity shortens open time, lower humidity extends it. Colour: Grey. Can be over painted once dry. Always test paint compatibility on a small area first. Shelf life: 12 months in unopened packaging stored in a cool, dry place Packaging: 310 ml cartridge Safety Wear gloves and eye protection. Avoid inhaling vapours and ensure good ventilation. If in eyes, rinse with running water and seek medical advice. Keep out of reach of children. Warranty Backed by a 10 year product guarantee when used as directed. This is in addition to your rights under the Australian Consumer Law. Notes Do a trial application for underwater or constantly wet repairs, as long term stability depends on the specific situation. Not for chemical resistant applications. Remove any skinned layer in the nozzle before reusing an opened cartridge.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $21.97

  • Packshot of Dunlop Premixed Resaflex Tile Adhesive 1kg

    Dunlop Dunlop Premixed Resaflex Tile Adhesive 1kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Premixed Resaflex Tile Adhesive 1 kg Overview Dunlop Premixed Resaflex Tile Adhesive 1 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $22.68

  • Packshot of Dunlop Wall Tile Adhesive 5.5kg

    Dunlop Dunlop Wall Tile Adhesive 5.5kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Wall Tile Adhesive 5.5 kg Overview Dunlop Wall Tile Adhesive 5.5 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $59.96

  • Packshot of Dunlop Trade Resaflex Tile Adhesive 5kg

    Dunlop Dunlop Trade Resaflex Tile Adhesive 5kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Trade Resaflex Tile Adhesive 5 kg Overview Dunlop Trade Resaflex Tile Adhesive 5 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $23.25

  • Packshot of Dunlop Gripper Fast Tile Adhesive 500ml

    Dunlop Dunlop Gripper Fast Tile Adhesive 500ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Gripper Fast Tile Adhesive 500 ml Overview Dunlop Gripper Fast Tile Adhesive 500 ml is a high quality multipurpose adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials common building materials ceramics wood metals some plastics stone Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Apply between 10°C and 30°C. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Cure time varies with product and conditions. Allow adequate time before loading or finishing. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean uncured product with a suitable solvent or water as applicable. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $32.80

  • Packshot of Dunlop Floorfix Professional Tile Adhesive 15 kg

    Dunlop Dunlop Floorfix Professional Tile Adhesive 15 kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Floorfix Professional Tile Adhesive 15 kg is a reliable cement based floor tile adhesive for porcelain and ceramic tiles chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 15 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Dunlop Floorfix for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Dunlop Floorfix Professional Tile Adhesive 15 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for General floor tiling High traffic residential areas Back buttering dense porcelain tiles Suitable surfaces The adhesive works well on the following surface types when properly prepared: Concrete slabs and screeds Cement sheet underlay Existing tiles that are clean and sound Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of as indicated on the bag for best wetting and transfer. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Respect open time and bed thickness. Allow adequate set before grouting and opening to traffic. Temperature and environmental performance Apply in suitable ambient conditions for predictable cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Damp sponge on fresh residue, water clean-up for tools. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store sealed and dry to prevent lumping. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $18.53

  • Packshot of Dunlop AAC Block Construction Adhesive 15 kg

    Dunlop Dunlop AAC Block Construction Adhesive 15 kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop AAC Block Construction Adhesive 15 kg is a reliable thin bed adhesive for autoclaved aerated concrete blockwork chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 15 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Dunlop AAC for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Dunlop AAC Block Construction Adhesive 15 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Laying AAC blocks in internal and external walls Creating straight and plumb courses with minimal waste Suitable surfaces The adhesive works well on the following surface types when properly prepared: AAC blocks and panels Suitable primed substrates as per system design Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of follow bag guidance for open time and pot life. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Mix to a creamy consistency and apply with a notched trowel. Align blocks within the open time and tap to level. Allow to set before further work. Temperature and environmental performance Protect fresh work from rain, frost, and high heat. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wash tools with water while material is fresh. Remove spills promptly. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep dry and use within shelf life. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $32.41

  • Dunlop Ready-to-Go Coloured Grout, Anti-Mould No-Mix - 800g Dunlop Ready-to-Go Coloured Grout, Anti-Mould No-Mix - 800g

    Dunlop Dunlop Ready-to-Go Coloured Grout, Anti-Mould No-Mix - 800g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Ready-to-Go Coloured Grout is a premium, pre-mixed grout for fast, clean results on walls and floors. No mixing, no mess, just open, apply, and buff for a smooth, long-lasting finish. The formula includes Grout Shield for anti-mould and anti-bacterial protection to help surfaces stay cleaner for longer. Suitable for interior and exterior applications, and available in a wide colour range to match or contrast your tiles. Ready-mixed convenience, apply straight from the tub Contains Grout Shield for mould and bacteria resistance Use on walls & floors, indoors & outdoors* Ideal for joint widths from 1–5 mm Great for rejuvenating old grout (min. removal depth: 1 mm walls, 2 mm floors) *Always follow the data sheet guidance for your specific area and exposure. Where to Use Ceramic, porcelain and most glazed tiles Bathrooms, kitchens, splashbacks, laundries, living areas Light-duty exterior tiled areas (check exposure & substrate) This grout is designed for typical domestic and light commercial tiling where a smooth, uniform finish is desired. Colours & Finish Available in a contemporary colour palette (e.g. whites and greys) to complement most tile styles. Use Dunlop’s colour selector to visualise combinations before you start. Coverage Coverage varies by tile size, joint width and depth. As a guide (per kg) of grout: Tile size (L×W×Thickness) Joint width 1.5 mm Joint width 3 mm Joint width 5 mm 25×25×4 mm mosaics ≈1.04 m²/kg ≈0.52 m²/kg ≈0.31 m²/kg 100×100×8 mm ≈2.08 m²/kg ≈1.04 m²/kg ≈0.63 m²/kg 200×200×8 mm ≈4.17 m²/kg ≈2.08 m²/kg ≈1.25 m²/kg Tip: Allow an extra 10–15% for wastage due to technique, tile type and site conditions. Directions (Summary) Prep: Ensure joints are clean, dry, and free from dust, adhesive residue and contaminants. For rejuvenation, remove at least 1 mm (walls) or 2 mm (floors) of old grout. Apply: Using a rubber grout float, force grout firmly into joints at a 45° angle. Strike & shape: Allow grout to firm in the joint (~15 mins). Shape joints as required. Clean: Wipe diagonally with a dense, damp sponge, rinsing frequently. Use minimal water to reduce shade variation and shrinkage. Buff: When touch-dry (typically 6–24 hrs), buff tile faces with a clean, dry cloth. Drying & Use Initial set at ~24 hrs at 23 °C / 50% RH Shower walls can be exposed to water after ~24 hrs Clean-Up & Storage Clean tools and residue with water while the grout is still wet. Reseal the tub between uses to prevent skinning. Store upright in a cool, dry place. Safety Read the Safety Data Sheet before use and follow PPE guidance. Avoid contact with eyes and prolonged skin contact. Keep out of reach of children.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $16.30 $0.02/g

  • Dunlop Tile-All Tile Adhesive Indoor & Outdoor 2Kg

    Dunlop Dunlop Tile-All Tile Adhesive Indoor & Outdoor 2Kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    High-Performance Multipurpose Wall & Floor Tile Adhesive This versatile adhesive is designed for fixing almost all tile types to a wide range of challenging surfaces, including water features and swimming pools. Key Features: Suitable for both walls and floors Can be applied over difficult surfaces, including water features Allows tiling over existing tiles Compatible with most types of ceramic and natural stone (excluding moisture-sensitive stone) Tile Types: Ceramic tiles Fully vitrified tiles Natural stone (excluding moisture-sensitive stone) Mosaics Porcelain Suitable Surfaces: Existing tiles Glazed ceramic tiles Metal Roughened fibreglass Timber (particleboard only) Application Areas: Walls and floors Indoor and outdoor Water features and swimming pools Coverage: Tile Size Trowel Size Coverage Up to 250 x 250mm 6-8mm 0.4m²/kg 250 x 250mm and larger 10-12mm 0.25m²/kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $49.42

  • Dunlop Tile Adhesive Wall & Floor Indoor & Outdoor 2Kg

    Dunlop Dunlop Tile Adhesive Wall & Floor Indoor & Outdoor 2Kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    This versatile adhesive is specially formulated for fixing most tile types, offering excellent flexibility and suitability for various surfaces. Key Features: Suitable for most tile types Can be applied over a variety of surfaces Suitable for interior timber (with proper preparation) Highly flexible Tile Types: Ceramic tiles Fully vitrified tiles Mosaics Porcelain tiles Natural stone (excluding moisture-sensitive stone) Suitable Surfaces: Cement render and concrete Fibre-cement sheets Existing ceramic and vinyl tiles Dunlop Undertile Waterproofing Metal surfaces Oil-based painted surfaces Plasterboard Indoor timber (must be adequately prepared) Application Areas: Walls and floors Indoor and outdoor use (as long as there’s no standing water and proper water run-off is ensured) Coverage: Tile Size Trowel Size Coverage Up to 250 x 250mm 6-8mm 0.8m²/kg 250 x 250mm and larger 10-12mm 0.5m²/kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $37.86

  • Dunlop Tile & Grout Concentrated Cleaner - Heavy Duty, 1L

    Dunlop Dunlop Tile & Grout Concentrated Cleaner - Heavy Duty, 1L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    An effective and easy-to-use neutral cleaner designed to remove general household dirt, grime, and oils from tiles and grout. Ideal for daily use, this cleaner is powerful enough to tackle grease in kitchens and bathrooms while being gentle enough for regular application. Key Benefits: Powerful cleaner for tiles and grout Effectively removes grease in kitchens and bathrooms Regular use reduces mould and mildew growth Suitable for general-purpose surface cleaning Cost-effective when diluted and applied by spray Easy to use for everyday cleaning Use On: Tiles, grout, and general household surfaces Surface Type: Walls and floors Location: Indoor and outdoor use Colour & Sizes: Size: 1L Item Code: 22504 Coverage: Wipe On: Dilute 10ml per 1L of water Spray On: Dilute 6ml per 1L of water Directions for Use: Test First: Before the first application of Dunlop Tile & Grout Cleaner, test a small amount of product in an inconspicuous area to ensure the desired result. Dilution: Mix 10mL of Dunlop Tile & Grout Cleaner per 1L of water. For best results, use hot water. Application: For general cleaning, apply the cleaner using a mop. For stubborn dirt, use an appropriate scourer or scrubbing pad that won't scratch the tile surface. Keep your tiles and grout clean and fresh with this powerful, easy-to-use cleaner, perfect for daily household maintenance.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $28.62

  • Dunlop Revive & Shine Your Polished Floors 500ml

    Dunlop Dunlop Revive & Shine Your Polished Floors 500ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Revive & Shine Dunlop Revive & Shine is a neutral, multipurpose cleaner and maintainer that enhances the appearance of sealed floors. Designed for use on timber, vinyl, and laminate floors, this product reduces the appearance of scuffing, increases durability, and improves gloss levels. For best results, use monthly to keep your floors looking their best. Key Benefits: Cleans and maintains timber, vinyl, and laminate flooring Provides extra durability, wear resistance, and shine Increases slip resistance Reduces the appearance of scuffing Ideal for monthly maintenance Suitable For Use On: Timber, vinyl, and laminate flooring Surface Type: Floors Location: Indoor Colour & Sizes: Colour: Milky (Dries Clear) Size: 500ml Item Code: 19882 Directions for Use: Dilution: Mix 20mL of Dunlop Revive & Shine per 1L of warm water in a bucket. Cleaning: Mop the floor with the solution. Spills: For spills, hose down the area and wash with large amounts of water. Note: The use of Personal Protective Equipment is recommended during application. Dunlop Revive & Shine is perfect for keeping your timber, vinyl, and laminate floors looking like new, providing enhanced shine, durability, and slip resistance.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $21.46

  • Dunlop Ready-Mixed Wall Tile Adhesive for Ceramic & Stone Tiles 5.5Kg

    Dunlop Dunlop Ready-Mixed Wall Tile Adhesive for Ceramic & Stone Tiles 5.5Kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    DUNLOP®WALL TILE ADHESIVE is a ready-mixed indoor wall tile adhesive. Ideal for all types of ceramic wall tiles and dimensional stones such as marble and granite, it can be used on a number of surfaces which include compressed fibre-cement sheets, plasterboard, cement render and adequately prepared painted surfaces (oil-based paint only). DUNLOP®WALL TILE ADHESIVE has superior flexibility and high grab to support even the heaviest of wall tiles. SURFACE PREPARATION Surfaces must be consistently flat and firmly fixed. Clean off dust, oil, grease and all loose contaminating materials or coatings. Ensure surfaces are dry, with no residue or permanent dampness. Prime porous surfaces (e.g. fibre- cement sheets, cement render) with DUNLOP®PRIMER & ADDITIVE beforehand and allow to dry. Cement Render Allow to cure for at least 7 days. Render should have a wood float finish. Plasterboard There is no need to prime the cardboard surface. However, where sheets are joined, DUNLOP®PRIMER & ADDITIVE must be used over the base jointing compound. Do not use the topping compound in areas which are to be tiled. Compressed Fibre-Cement Sheets Remove surface dust with a damp sponge and prime with DUNLOP®PRIMER & ADDITIVE and allow to dry before tiling. Painted Surfaces Oil-based paint should be roughened mechanically and loose flaking paint should be removed. Ensure the paint is suitable for tiling over. Thoroughly remove water-based paints. Do not use paint stripper or solvents. Allow surface to dry after cleaning. MIXING No mixing required. APPLICATION As a general guide use a 6mm notch trowel to spread adhesive achieving a minimum 1mm bed thickness. Do not wet tiles before fixing. If backs of tiles are dusty clean with a damp sponge. Spread the adhesive with the notches running horizontally across the wall. Spread only one square metre at a time and ensure a skin has not developed on the adhesive before bedding tiles. Press and slide the tile into position ensuring the whole of the back of the tile is in good contact with the adhesive. Use tile spacers if desired to ensure even spacing. Remove any surplus adhesive on face of tile or between joints before it sets. Adjustment of tiles should be carried out within 60 minutes of laying (at 23°C and 50% humidity). COVERAGE DUNLOP®WALL TILE ADHESIVE will cover approximately 0.5m2per kg. Coverage will vary depending on the condition of the surface being tiled and application technique. DRYING TIME DUNLOP®WALL TILE ADHESIVE will dry in approximately 24 hours depending on ambient temperature, porosity of surface and tiles. MOVEMENT JOINTS Incorporate movement joints at 3.5m intervals and at internal corners. Any structural movement joints must be carried through to the face of the tiling, at junctions between different background material and at fixtures interrupting the tile surface. These joints should be about 6mm wide and and kept free from adhesive. They should be filled with a high quality flexible material e.g. DUNLOP®COLOURED SILICONE. GROUTING Wait until adhesive has set. This takes approximately 24 hours. Remove tile spacers and use DUNLOP®GROUT adding DUNLOP®PRIMER AND ADDITIVE to enhance colour, impart a degree of flexibility and reduce porosity and staining. For easier maintenance seal with DUNLOP®GROUT SEALER. CLEAN UP While it is still fresh, DUNLOP®WALL TILE ADHESIVE can be cleaned off with a damp sponge. Tools, hands and material soiled with adhesive can be easily cleaned with water as long as the adhesive is still fresh. CAUTION Do not use DUNLOP®WALL TILE ADHESIVE to fix green marble. Do not use DUNLOP®WALL TILE ADHESIVE in continuous immersion applications e.g. swimming pools, tanks etc.. Do not use DUNLOP®WALL TILE ADHESIVE over non- absorbent substrates and waterproofing membranes due to prolonged drying times. DUNLOP GUARANTEE Product is guaranteed for 10 years when installed to manufacturers instructions. Manufactured under a quality system certified as complying with ISO 9001 by an accredited certification body. Material Safety Data Sheets are available TECHNICAL DATA Characteristics of product: Colour: White Viscosity: 790 000 cps S.G: 1.47g/cm3 pH: 9.1 Form: Viscous paste Application Properties: (@23°C and 50% relative humidity) Open Time: 80 mins Adjustability Time: 60 mins Mechanical Properties: Fundamental Characteristics Shear adhesion strength: Shear adhesion strength after aging: 2.5 Mpa (AS 4992.1) Minimum requirements 1.0Mpa (D1) 3.5 Mpa 1.0Mpa (D1)   SAFETY Keep out of the reach of children. If skin contact occurs wash skin thoroughly with running water. If swallowed, give a glass of water and contact Poisons Information Centre. In case of contact with eyes, rinse with plenty of water and contact a Doctor. MSDS available on request.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $66.83

  • Dunlop Premixed Resaflex Tile Adhesive Ready Mixed 4Kg

    Dunlop Dunlop Premixed Resaflex Tile Adhesive Ready Mixed 4Kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Premixed Resaflex Tile Adhesive Ready to use, flexible and tough ceramic tile adhesive for dependable indoor tiling. Ideal for interior walls and fibre-cement sheet residential floors. No mixing required, spreads smoothly, and delivers a secure bond when applied at the correct bed thickness. Key Benefits Ready mixed convenience for faster start and less mess Flexible bond that helps accommodate minor movement Non-slump paste with excellent grab on vertical surfaces Suitable for common interior wall substrates and fibre-cement sheet floors Where To Use Walls: Interior applications on cement render, plasterboard, and fibre-cement sheet Floors: Residential fibre-cement sheet floors Tiles: Ceramic and similar porous tiles Surface Preparation Surfaces must be flat, clean, dry and firmly fixed. Remove dust, oil, grease and loose materials. Prime porous surfaces like cement render and fibre-cement sheet, and any base jointing compound on plasterboard, then allow to dry. Remove water based paints completely. If paint integrity is uncertain, roughen or remove. Application Use an appropriate notched trowel: as a guide 6 mm for walls, 10 mm for floors. Spread only as much as you can tile within open time, typically about 1 m² at a time. Ensure no skin has formed. Bed tiles into a 1.5 mm to 6 mm adhesive layer. Press and slide to ensure full contact. Clean excess adhesive from tile faces and joints before it sets. Coverage Guide Tile Size Notch Size Approx. Coverage per kg Up to 150 x 150 mm 4.5 mm ~0.7 m² 150 x 150 to 250 x 250 mm 6 to 8 mm ~0.5 m² 250 x 250 mm and over 10 to 12 mm ~0.3 m² Coverage varies with substrate condition, trowel angle and application technique. Drying and Grouting Typical set time is about 24 hours at 23°C and 50% relative humidity. Allow longer for dense tiles or cool and humid conditions. Grout after adhesive has set, usually after 24 hours. Movement Joints Provide joints around perimeters and at intervals consistent with good tiling practice, for example at about 5 m on floors and about 3.5 m along walls. Keep joints about 6 mm wide and free of adhesive and grout. Fill with a suitable flexible sealant. Limitations Not suitable over concrete where extended drying can occur. Not for areas subject to water immersion such as pools. Do not use for non-porous tiles over non-porous substrates or for moisture-sensitive stone. Final adhesive bed must be at least 1.5 mm and not more than 6 mm thick. Clean Up Clean tools and any fresh residue with water before the adhesive sets. Technical Data Type Single part viscous paste Colour Grey Bulk Density ~1.2 g/cm³ pH ~8.5 Slip 0 mm Extended Open Time ~1.2 MPa after 30 min Shear Bond Strength ~0.9 MPa Pack Sizes and Shelf Life Available in 1 kg, 4 kg, 10 kg and 20 kg pails Shelf life 12 months in unopened packaging stored in a dry place Good Practice Tips Use tile spacers for consistent joints and remove them before grouting. Prime porous substrates as directed for best results. Always follow movement joint requirements for long-term performance.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $59.48

  • Dunlop Premium Floor Sealer Easy Safe Application 4L

    Dunlop Dunlop Premium Floor Sealer Easy Safe Application 4L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. Safety: Avoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. If swallowed, seek immediate medical advice. Always refer to the MSDS available on the Dunlop website.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $139.40

  • Dunlop Premium Floor Sealer Easy Safe Application 1L

    Dunlop Dunlop Premium Floor Sealer Easy Safe Application 1L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. Safety: Avoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. If swallowed, seek immediate medical advice. Always refer to the MSDS available on the Dunlop website.

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $48.79

  • Dunlop Multi-Purpose Primer & Additive – 4L

    Dunlop Dunlop Multi-Purpose Primer & Additive – 4L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Primer & Additive is a water-based multipurpose solution that improves the bond between porous substrates and adhesives, waterproofing membranes, or screeds. It can be used as a primer before tiling or as an additive to strengthen screeds and grouts. Surface Preparation: Ensure the surface is clean, dry, and free of dust, oil, wax, paint, or other contaminants. For new concrete or screeds, allow to cure completely. Fill cracks and voids using a patching compound. Application Instructions: As a primer, dilute 1 part Dunlop Primer & Additive with 3 parts water. Apply evenly using a brush or roller. Allow it to dry for at least 30 minutes before applying adhesives or membranes. As an additive, replace part or all of the mixing water in tile adhesives or grouts to improve flexibility and adhesion. Follow the manufacturer's recommended ratios. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Allow to dry for at least 30 minutes before overcoating. Drying may vary depending on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based acrylic polymer pH: Neutral Appearance: Milky white liquid Shelf Life: 12 months (unopened in cool, dry conditions)

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $64.80

  • Dunlop Multipurpose Floor Leveller – 5kg

    Dunlop Dunlop Multipurpose Floor Leveller – 5kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Multipurpose Floor Leveller is a high-flow, cement-based compound ideal for smoothing and levelling uneven internal concrete surfaces before applying tiles, vinyl, carpet, or other floor coverings. Designed for ease of use, it pours and spreads to form a smooth surface ready for foot traffic and covering in minimal time. It’s perfect for domestic and light commercial applications. Surface Preparation: Ensure the surface is sound, dry, and clean. Remove all traces of dust, grease, oil, curing compounds, wax, or any loose particles. New concrete must be fully cured. Mechanically remove surface laitance or contamination. Porous surfaces may require priming to reduce absorption and improve adhesion. Priming (if required): Apply a compatible primer using a broom or roller and allow it to dry before applying the leveller. On extremely porous substrates, a second coat may be necessary. Mixing Instructions: Slowly add the contents of the 5kg bag to approximately 1L of clean water while stirring with a mixing paddle. Mix for 2–3 minutes until a lump-free, smooth consistency is achieved. Do not retemper once the mixture begins to set. Application Instructions: Pour the mixed product onto the floor and spread using a steel trowel or smoothing blade. The product will self-level and settle to a smooth finish. Apply at a thickness of 1–10mm in one application. Protect from foot traffic until it is fully cured. Coverage: Covers approximately 3.5m² at 1mm thickness per 5kg bag. Coverage varies with substrate texture and thickness. Drying Time: Walkable: 4 hours Ready for tiling: 4–6 hours Ready for other coverings: 24 hours Dry times will vary depending on temperature, humidity, and layer thickness. Clean Up: Clean tools and mixing equipment with water immediately after use. Do not allow the product to dry on tools or surfaces. Technical Data: Type: Cement-based self-levelling compound Application Thickness: 1mm to 10mm Working Time: 15–20 minutes Walkable: After 4 hours Final Cure: Up to 24 hours Colour: Grey Shelf Life: 12 months if stored in original, sealed packaging

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $40.20

  • Dunlop High-Performance Wall Tile Adhesive for Heavy Tiles 750g

    Dunlop Dunlop High-Performance Wall Tile Adhesive for Heavy Tiles 750g

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    High-Performance Ready-Mixed Ceramic Tile Adhesive This high-grab adhesive is designed to support even the heaviest wall tiles, providing superior flexibility for interior applications, particularly in kitchens and bathrooms. Key Features: Ready-mixed adhesive High grab for heavy wall tiles Superior flexibility Tile Types: Ceramic wall tiles Granite Marble (excluding moisture-sensitive stone) Suitable Surfaces: Cement render Fibre-cement sheets Painted surfaces (properly prepared) Plasterboard Application Areas: Indoor walls Coverage: 0.5m² per kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $19.86

  • Dunlop Grout Sealer 250ml

    Dunlop Dunlop Grout Sealer 250ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    A water-based protective sealer which penetrates and cures within the pores of the grout. The sealer is fast drying and the bottle contains a brush for easy application. A water-based protective sealer Deep penetrating into the grout Easy to use brush for perfect sealing over grout Fast drying formula Coverage Seals up to 25m2 per 250ml

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $18.48

  • Dunlop Floor Repairer Rapid Patch Mortar – 5kg

    Dunlop Dunlop Floor Repairer Rapid Patch Mortar – 5kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Floor Repairer Rapid Patch Mortar is a high-performance, fast-setting compound ideal for repairing holes, cracks, and uneven surfaces on internal floors. Suitable for use prior to the installation of tiles, vinyl, carpet, or other floor coverings, it delivers a smooth, level finish ready for light foot traffic within 45 minutes and covering applications in as little as 2 hours. Surface Preparation: Ensure the substrate is clean, sound, and free of grease, dust, oil, paint, or other contaminants. Surfaces should be dry and firm. Smooth or sealed surfaces must be roughened or etched. For porous substrates like timber, fibre-cement, or plasterboard, priming may be required. For floors in direct contact with soil, a moisture barrier should be used before applying the patch mortar. Mixing Instructions: Add 5kg of product into approximately 1.5L of clean water in a clean container. Mix thoroughly with a mixing paddle to a lump-free, smooth consistency. Mix only what can be used within 15 minutes. Application Instructions: Apply with a steel trowel to the required thickness (up to 20mm in a single application). Shape and smooth the surface before the material begins to set. For deeper repairs, additional layers can be applied once the initial layer has set. Avoid adding extra water once mixed. Coverage: Approximately 3m² at 1mm thickness per 5kg bag. Coverage varies with surface texture and thickness applied. Drying Time: Initial set: ~45 minutes Ready for coverings (tiles, vinyl, carpet): ~2 hours Final cure: 24 hours (depending on thickness and ambient conditions) Clean Up: Clean tools and equipment immediately with water before the mortar sets. Technical Data: Type: Rapid-setting cementitious repair mortar Application Thickness: Up to 20mm Pot Life: 15 minutes Foot Traffic: 45 minutes Ready for Coverings: 2 hours Colour: Grey Shelf Life: 12 months in original unopened packaging stored in a dry area

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $39.52

  • Dunlop Express Wet Area Waterproofing Membrane – 5kg

    Dunlop Dunlop Express Wet Area Waterproofing Membrane – 5kg

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Express Wet Area Waterproofing Membrane is a high-performance, fast-drying liquid membrane designed for use in internal wet areas including bathrooms, showers, laundries, and kitchens. This flexible, water-based acrylic polyurethane formulation creates a seamless and highly durable waterproof barrier that is tile-ready within hours. It’s suitable for use under tile adhesives, screeds, and other flooring products. The product forms a tough, elastomeric layer that resists movement, cracking, and water penetration. It meets the requirements of Class III membranes and is suitable for both floor and wall applications. Surface Preparation: Ensure all surfaces are clean, dry, and structurally sound. Remove dust, grease, oil, curing compounds, and loose or flaking materials. Prime all surfaces using a compatible primer. On porous or highly absorbent surfaces, apply a second primer coat if needed. Any existing cracks, gaps, or joints should be sealed or reinforced using bond breakers or reinforcing fabric. Application Instructions: Apply the membrane using a brush or roller. Two coats are required for effective waterproofing. First coat should be applied in one direction. Once dry to the touch (approx. 2 hours), apply the second coat in the opposite direction. Membrane should extend at least 150mm up walls in general wet areas and 1.8m in shower recesses. Waterproofing must be applied continuously and without breaks or pinholes. Use reinforcing fabric over joints and corners if required. Avoid application in conditions below 10°C or above 35°C. Coverage: Approximately 1m² per litre per coat. A 5kg pail covers roughly 2.5m² with two coats, depending on surface porosity. Drying Time: Touch dry: 1–2 hours Recoat time: 2 hours Ready for tiling: 4–6 hours Fully cured: 24 hours Drying times will vary with ambient temperature and humidity. Clean Up: Clean tools and equipment immediately after use with water. Do not allow membrane to dry on tools. Technical Data: Type: Water-based acrylic polyurethane Classification: Class III membrane Application Method: Brush or roller Flexibility: High Water Resistance: Excellent Colour: Grey Shelf Life: 12 months (unopened in cool, dry conditions)

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $80.40

  • Dunlop Damp-Proof Waterproofing – 4L

    Dunlop Dunlop Damp-Proof Waterproofing – 4L

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    Dunlop Damp-Proof Waterproofing is an acrylic brush-on membrane designed to prevent rising damp, efflorescence, and resist negative hydrostatic pressure. It adheres excellently to substrates including brick, masonry, concrete block, concrete, stone, and timber, and can be easily applied using a brush or roller. Once cured, it can be overcoated with most decorative paints. Surface Preparation: Ensure all surfaces are structurally sound and free from existing coatings, adhesives, and efflorescence to achieve maximum bond strength and resistance to hydrostatic pressure. Surfaces may be damp but not wet and must be cleaned free of dirt, grease, oil, or other contaminants. Fill holes and non-structural cracks with a suitable floor repairer before application. Application Instructions: For Floors: Spread the material using a brush or long nap roller to achieve coverage, then finish with a long nap roller. For Walls: Apply using a brush, roller, or spray, ensuring even coverage. Work the material into voids to avoid pinholing. For areas affected by hydrostatic pressure, apply a minimum of two coats. The second coat can be applied after 4 hours. Ensure uniform coverage and the required dry film thickness per coat. Coverage: Single Coat: Approximately 3m² per litre, per coat, when used as a barrier to efflorescence or as a moisture-resistant coating over green concrete. Multiple Coats: For areas with hydrostatic pressure, two coats are required at a coverage rate of 1.5m² per litre per coat. Additional coats may be necessary to achieve uniform coverage. Drying Time: Allow the membrane to cure for 24 hours before applying adhesives, mortars, decorative coatings, or other surface treatments. Ensure the membrane is not damaged during subsequent treatments. For floor surfaces, allow the final coating to cure for at least 24 hours before further treatment to minimize the risk of mechanical damage. Clean Up: Wash all equipment with water or a water/detergent mixture immediately after use. Technical Data: Base: Acrylic Application Temperature: 10°C to 35°C Dry Film Thickness: Achieve required thickness as per application guidelines Curing Time: 24 hours before overcoating Shelf Life: Refer to packaging for details

    In Stock  Express Post: 1-3 Days | Standard Post: 2-5 Days

    $144.00

Dunlop

Dunlop is a leading name in tiling and flooring systems, delivering innovative products that combine strength, durability, and ease of use. Backed by decades of expertise and trusted by professionals across Australia, Dunlop provides complete solutions for both residential and commercial projects.

At Glues Australia, our Dunlop range includes:

  • Tile Adhesives – High-performance adhesives designed for ceramic, porcelain, stone, and mosaic tiles.

  • Grouts – Flexible and durable grouts available in a wide variety of colours for a perfect finish.

  • Floor Levellers & Primers – Fast-setting, smooth finishes that prepare surfaces for flawless installation.

  • Waterproofing Systems – Proven protection for bathrooms, kitchens, and other wet areas.

  • Repair & Maintenance Products – Easy solutions for cracks, patching, and surface restoration.

Choose Dunlop for reliable performance, professional results, and products that are tested to withstand Australia’s toughest conditions. Whether you’re a tradesperson or a DIY renovator, Dunlop makes every project easier, faster, and longer-lasting.

Login

Forgot your password?

Don't have an account yet?
Create account