Heat Resistant

PC-Fahrenheit™ Putty Epoxy is the choice for temperatures up to 260° C. It is supplied as a premeasured stick that you mix with fingers. Fast curing (60 min). Best for steam heat applications. A toolbox must. Great on copper and iron. Here are just a few specific uses (there are hundreds of other uses): Seal cracked steam or hot water radiator Stop leaking steam fittings Fill hole in heat exchanger Attach thermocouple to hot surface Seal chimney ductwork How to prepare a surface for bonding with PC-Fahrenheit™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Fahrenheit™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Fahrenheit™ repair a leaking steam radiator? PC-Fahrenheit™ resists higher temperatures and is suitable for repairing steam pipes and radiators. Can PC-Fahrenheit™ be used in a fireplace or wood burning stove? PC-Fahrenheit™ will withstand temperatures up to 260°C. A fireplace or wood burning stove creates temperatures exceeding 260°C. Can PC-Fahrenheit™ be used to seal heater chimney duct? PC-Fahrenheit™ is excellent for use on sheet metal and the temperature is within an acceptable range. Can PC-Fahrenheit™ seal a rust hole in barbecue grill? PC-Fahrenheit™ can be used on the barbecue grill exterior but is not recommended for the interior. How long should PC-Fahrenheit™ be mixed before applying? Mix PC-Fahrenheit™ for 45 to 60 seconds then immediately apply. What is the temperature limit? PC-Fahrenheit is not intended to exceed 260°C. -  Will PC-Fahrenheit™ burn? PC-Fahrenheit™ is not flame resistant and may burn if exposed to direct flame. Does PC-Fahrenheit™ stick to car radiator? Car radiators are made of various metals and plastic composites. Test for adhesion and test for leaks.

Read more less

Clear Flexible Fabric Glue A versatile, water-based fabric adhesive designed for clothing repairs, craft projects, and soft furnishings. It forms a strong, long-lasting, flexible bond on most porous fabrics and dries clear in thin films for a neat, professional finish. Once fully cured, the bond is machine washable, can be tumble dried, and is safe to iron. Key Features Permanent, flexible bond for clothing and crafts Water-based, low odour formula Dries clear in thin applications Machine washable and tumble-dry compatible after full cure Heat resistant—safe to iron over the bonded area Easy squeeze application; cleans up with warm soapy water while wet Ideal Uses Hems, trouser turn-ups, and pocket repairs Attaching cloth labels, badges, and patches Securing frayed lace ends and trims Curtain hems and decorative soft furnishing accents General fabric repairs on cotton, denim, linen, felt, leather and similar porous textiles Directions Preparation: Ensure surfaces are clean, dry, and free from dust or grease. At least one surface must be porous. Test first: Trial on an off-cut or hidden area, especially with light or open-weave fabrics. Apply: Spread a thin, even layer to the non-visible side or back of the fabric. Join parts and press for several seconds. Initial handling: Light handling is typically possible after about 1 minute; avoid stressing the bond. Optional set boost: For improved bonding, gently iron-press ~5 minutes after gluing (use a pressing cloth). Full cure: Reaches full effective strength after 24 hours. After curing, the item may be machine washed, tumble dried, and ironed. Clean-Up While wet: Wipe away with warm, soapy water; repeat if needed, rinse and dry. When dry on smooth, non-porous surfaces: Gently rub off or use warm, soapy water. When dry on fabrics: Difficult to remove—prevent excess and work carefully. Compatibility & Notes Best on porous textiles: cotton, denim, linen, felt, leather, and similar materials. Not suitable for non-porous materials or 100% nylon/polyester fabrics. Avoid heavy application or excessive pressure on light or open-weave fabrics to minimise show-through or darkening. Specifications Chemistry Acrylic copolymer (water-based) Appearance Milky white liquid; dries clear in thin films Density 1.07 ± 0.02 g/cm³ Solids Content 61–63% Viscosity Up to ~1,000 cps pH 4–6 Initial Handling Time ~1 minute (varies with material, temperature, humidity) Full Cure / Maximum Strength ~24 hours Washability & Heat Machine washable; tumble dry and iron once fully cured Clean-Up (Wet) Warm soapy water Pack Size 20 mL (blister) Storage Cool, dry place around 20 °C; keep container tightly closed; protect from moisture Shelf Life Up to 18 months from manufacturing date (unopened, stored as directed) Not Suitable For 100% nylon, 100% polyester, non-porous materials, very fine/delicate fabrics (e.g., some silks, wools, linens)

Read more less

Sugru is a Multi-Purpose, Mouldable Glue for fixing, Bonding and DIY Mouldable Out of the pack, Sugru Mouldable Glues are designed to feel soft and malleable like play-dough. Roll the material in your fingers. Press it where you need it, and mould it by hand into any shape. From an ultra-thin patch to a shock-absorbing bumper, you have 30 minutes to shape it, smooth it, and reposition it as required. Flexible Leave for 24 hours. Thanks to some clever science and advanced technologies, Sugru Mouldable Glues react at room temperature, simply on exposure to air. They crosslink into strong, flexible and tactile silicone rubbers overnight. Sugru Mouldable Glues will flex with the materials they're applied to, so you can fix things that need to bend. They work like nothing else on leathers, fabrics or flexible plastics. Waterproof & Durable Once cured, Sugru Mouldable Glues are waterproof and long-lasting, just like other silicone rubbers. So you can use them in challenging environments like wet bathrooms, shower and sink areas – even outdoors with long-term exposure to the sun, sea and other weather conditions. Multi-Material Sticks permanently to lots of materials like glass, ceramic, wood, metal and plastics*. Strong Once cured, it stays in its shape permanently and will remain bonded, often for years to come. Holds Up to 2KG/4.4LB Ensure surfaces are clean and dry. A 5g/.17oz single-use pack can hold up to 400x its own weight.  Heat and Cold Resistant Comfortable at high and low temperatures up to 180°C (356°F) and down to -50°C (-58°F). Durable Flexibility combined with strong adhesion ensures that your fixes don’t become brittle or crack. Waterproof Ensure surfaces are dry before use. It can even be used for sealing applications indoors and out. Flexible The thickness of your fix will determine its ultimate flexibility, a thin layer will deliver maximum flex. Shock Resistant Excellent dampening properties can deliver vibration resistance and shock protection. Insulating Like other silicones, it has good thermal and electrical insulation properties**. Weatherproof Excellent ozone and UV resistance. Only slight fading after years in direct sunlight. Stick It Sugru sticks permanently to lots of materials like glass, ceramic, wood, metal and plastics*. Mould It You have 30 minutes to fix, build and create. Sets Strong In 24 hours, it turns into a strong and durable silicone rubber that stays stuck.

Read more less

Extreme temperatures take a toll on rearview mirrors. After a bitter cold winter or hot summer, they tend to fall off. Our Rear View Mirror Adhesive is formulated to be strong and quick—enabling you to have your rear view mirror reattached in minutes. Works best on Glass to Glass Glass to Metal Metal to Metal Pacer Technology Super Glue’s Rear View Mirror Adhesive (14104, 15193) is a two-part system used for bonding rear view mirror brackets to windshields and for: Glass to metal Glass to glass Metal to metal Properties: Appearance: Part A – Activator/Accelerator – light blue transparent liquid Part B – Adhesive – yellow liquid adhesive Tensile Shear Strength (steel to steel): 2000 – 3000 psi Directions: Use in a well-ventilated area. Mark location on the outside of windshield with a removable marker. Make sure bracket is positioned correctly. Refer to the card for proper opening instructions. 1. Apply Activator to both surfaces. Allow 1 minute to dry. 2. Apply 2 drops of adhesive to the metal surface to be bonded. 3. Mate parts together using sufficient pressure to spread adhesive. Hold parts together firmly for 1 minute. Allow 1 hour before handling. Full strength develops in 24 hours. For optimum results, wait overnight before attaching the mirror to a bracket. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Activator – Contains isopropyl alcohol. CAUTION: Flammable. Irritating to eyes. Mild skin irritant. Do not ingest. If swallowed seek medical advice immediately and show this container label. Use and store in a well-ventilated area. KEEP OUT OF REACH OF CHILDREN. Adhesive – Contains methacrylate esters and acrylic acid. CAUTION: Irritating to eyes and skin. May cause sensitization by skin contact. Avoid contact with skin & eyes. In case of eye contact, rinse immediately with water for 15 minutes and seek medical advice. For skin contact, wash well with soap and water. If swallowed seek medical advice immediately and show this container label. KEEP OUT OF REACH OF CHILDREN. 

Read more less

Tarzan's Grip Shockproof Super Glue is a high strength, rubber toughened adhesive that dries clear for a multitude of applications. In addition to offering a superior bond on metals, it is ideal for use with wood, rubber, leather, china, paper and most plastics. It resists extreme temperatures of up to 150C. Sets in around 2 to 3 minutes Impact resistant Heat resistant Superior bond on metals

Read more less

A solvent-based, heat resistant, flexible contact adhesive suitable for bonding both absorbent and non-absorbent surfaces. It forms an instant bond on contact of two surfaces. The gel form allows application without dripping or ‘stringing’. Great for vertical surfaces. Features Heat resistance up to 130C No clamping required Suitable for interior and exterior jobs Cured adhesive is resistant to dilute acids and alkalis Immediate set on contact. Maximum strength after 24 hours Gel Grip has a thicker consistency than Kwik Grip and so is ideal for vertical applications as it won’t run Gel form prevents running or stringing Easy to spread by brush and ideal for use on vertical surfaces Where can this product be used? Vertical surfaces where dripping and running is a concern Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench or table tops Areas where clamping or pressing facilities are either not available or difficult to use Patching vinyl Flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Fixing laminate to tables, benchtops etc Repairing canvas tents and outdoor equipment Bonding metal or laminate sheeting Replacing trim, rubbers and weather seals in cars Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers etc Some plastics such as vinyl sheeting and polystyrene are attacked by Gel Grip. Test in an inconspicuous area prior to application. Can cause discolouration and bubbling when used for vinyl flooring materials, seek the advice of flooring material manufacturer before using Gel Grip. We recommend Kwik Grip Advanced for these applications Contains highly flammable solvent and care should be taken to ensure all fire precautions are observed. Cannot be used for application in temperatures below 10oC. Suitable for porous materials but not for rough, ill-fitting surfaces. (Consider the suitability of alternative products such as Liquid Nails for rough ill-fitting surfaces). What materials is this product suitable for? Cork Rubber Felt Canvas Leather Metals Timber Laminated plastics (laminex, formica) Hardboard Compressed board How to use this product Ensure that surfaces to be bonded are clean, dry and free from grease or paint. Cut laminated plastic sheet slightly oversize all round. Completely cover both surfaces with adhesive and keep apart until touch dry – no more than 40 minutes. Position the items carefully, still keeping surfaces apart with dowels or heavy craft paper and working from one edge press surfaces firmly together. Secure bond by running a roller over the bonded surfaces or else by hammering the surface from the centre outwards using a padded block. For bonding other materials, apply as for laminated plastics above. When small surface areas are to be joined a wet bond may be used. Simply apply Gel Grip to one surface then bring the surfaces together and clamp until dry. Handy tips Care should be taken to test plastics prior to use as solvents present will attack some grades such as polystyrene and sheet vinyl. Use Kwik Grip Advanced for these applications. Keep container sealed when not in use. Coverage – up to 5 square metres/litre (bonded area 2.5 square metres/litre) depending on porosity of surfaces and thickness of applications For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Clean Up While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Gel Grip has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent. Safety tips Ensure thorough ventilation when using. Avoid using in a confined space for prolonged periods. Use Kwik Grip Advanced as a low fume alternative. Avoid skin contact as solvents in Gel Grip have a degreasing effect and may result in irritation. If in eyes flush with plenty of water for 15 minutes. Seek medical advice. If poisoning occurs, contact a doctor or Poisons Information Centre. Phone Australia 131 126 or New Zealand 0800 764 766. If swallowed, do not induce vomiting. Give a glass of water. Highly flammable. Do not use in the same area as flame, fire or spark producing apparatus or machinery. This product should NOT be accessible to juveniles, because of its solvent content. For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use Clean Up While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Gel Grip has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent. Store in a cool area away from ignition sources and out of direct sunlight.

Read more less

Ultra-High strength supa glue that dries clear. Gives great strength as well as flexibility and heat resistance. Performance above and beyond normal Supa Glue. Features Bonds a variety of surfaces Extremely fast setting Dries Clear for clean, neat results Water resistant No clamping necessary No mixing required Maximum strength achieved in 12 hours Only takes 45 seconds to achieve an initial bond Self-piercing, clog-free cap Forms a strong, flexible bond Impact Resistant – 4 times greater impact resistance than normal supa glues Superior bond on metals – up to 6 times stronger bond on steel than normal supa glue. Up to 4 times stronger bond on aluminium than normal supa glues Heat Resistant to 120°C permanently, 150°C intermittently Comes with a nozzle for easy, accurate application Appearance Clear thick liquid dries to a colourless film. Where can this product be used? Ideal for small repair jobs or when immediate results are required Fixing a broken door knocker Refixing wooden or metal door handles Repairing crockery safe to put in the dishwasher Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or other materials containing alkaline elements Not recommended for highly porous surfaces What materials is this product suitable for? Bonds a variety of porous and non-porous surfaces Metals Wood China Rubber Leather (test first as leather may become hardened or discoloured) Some plastics How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Refer to handy hints for cleaning tips. Pierce seal at end of the tube by attaching nozzle and cap and turning clockwise. Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. Allow 12 hours for sufficient bond strength for practical use. Handy tips Supa Glue can create a white residue on the surface of materials if the area is not well ventilated. Clean the affected area with acetone to remove (most nail polish removers) residue. Excellent when used with other adhesives, as the temporary tack. For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting. After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. In the event that fingers get stuck together – don’t panic! Slowly twist fingers in the opposite direction in hot soapy water. Acetone (most nail polish removers) or Olive oil can also be used to remove Quick Fix from the skin. While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Supa glues cure more slowly when large amounts are used. For faster cure use sparingly. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method. Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into the cap, preventing a tight seal after use. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin is soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively, rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary to apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in the skin. Do not use near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly. Ensure cap is replaced and store in a cool dry place. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.

Read more less

A 15-minute, two-part adhesive and filler system that eliminates the need for welding or brazing. It repairs, fills and bonds to iron, steel, brass, bronze, aluminum and copper. Once cured, it can be drilled, tapped, threaded, filed, sanded and painted. Resists most automotive, shop and cleaning fluids. Withstands temperatures to 300°F intermittent. Over 3,000 PSI shear strength on steel. Automobile Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings Heavy Duty Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings Marine Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings PRODUCT BENEFITS • No heating required • Holds in 10 minutes • Useable in 30 minutes • Good moisture resistance • Withstands extreme temperatures • Non-flammable TYPICAL APPLICATIONS • Cracked transmission cases • Chipped heads • Rear end castings • Cracked blocks • Cracked intake manifolds • Damaged keyways • Split stampings DIRECTIONS FOR USE 1. Before starting, make sure your work area is protected from accidental spills. Surfaces must be clean, dry and free of grease and oil. 2. Roughen smooth surfaces to be repaired with sandpaper. 3. Apply in ventilated area. Vapors may irritate eyes and nose. 4. Squeeze out equal amounts of bonding agent and curing agent. 5. Mix together thoroughly until color is uniform. 6. Apply immediately to both surfaces and press together. Remove excess glue at once. 7. Allow bond to set for 10 minutes before moving or handling. 8. After 24 hours, typical shear strength on steel is 3000 PSI. 9. Cure time will be slower in colder weather. For Cleanup 1. Cleanup must be completed before curing is complete. Use acetone or mineral spirits for cleanup. 2. Clean hands with Permatex Fast Orange hand cleaners. Chemical / Solvent Resistance The product retains effective properties when in contact with water, oil, fuels, and most solvents. Not recommended for long term exposure to chemicals and solvents. NOTE: Permatex Cold Weld Bonding Compound will not bond polyethylene and polypropylene plastics. GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as an adhesive for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).

Read more less

Parfix Fast Grip is a solvent-based contact adhesive that is heat and water-resistant, making it suitable for use in kitchens and bathrooms. Immediate strong bond Heat and water resistant Brush application

Read more less

A transparent polyurethane paste adhesive. SuperGrip 30 Minute is a versatile, ready to use, fast curing, general purpose construction adhesive.  Uses Bonding of: • Edge bonding of particle board flooring • Timber & MDF • Marble & Stone • Concrete • Block/blocks • Glass • Fibre cement • Tiles • Rubber • Metals • Aluminium Advantages • 100% waterproof (BS-EN204) • Incredibly strong • Bonds almost anything, including LOSP treated timber • Non drip • No shrinkage • Cures in 30 minutes* • Interior and exterior use • High temperature resistance (minus 30ºC to 100ºC) • Cures transparent • Does not stain  Technical Data (Typical) Density: 1.12 g/cm³ Solids content: 100% approximately Cure type: Humidity curing Application temperature: 5ºC to 35ºC Service temperature: -30ºC to +100ºC Relocation time: Approximately 5-10 minutes depending on temperature and ventilation. Cure time: Approximately 30 minutes, depending on temperature, moisture content of surfaces and adhesive thickness. Strength will increase over 24 hours. Flammability: Non flammable

Read more less

Red, 1-part, flowable smooth, acetoxy silicone paste sealant.   LOCTITE® SI 596 is a red, 1-part, flowable smooth, acetoxy silicone paste sealant. It forms a tough, flexible, waterproof, oil-resistant silicone rubber bond. It is also used as a sealant and adhesive in industrial furnaces, ovens, boilers, exhaust stacks, high temperature ducting and heating elements in electrical appliances. Resists ageing, weathering and thermal cycling without hardening, shrinking or cracking Typically used in applications with an operating range of -50°C to +250°C   Technical Information Colour Red Fixture Time 30 min. Fixture Time Temperature 30 °C Full Cure Temperature 77 °F Mix Ratio No Mix Physical Form Paste Skin Formation Time 8 min. Temperature -75 - 600 °F

Read more less

IMPREGNATED WITH E-POX E RESIN WITHSTANDS HEAT UP TO 260°C Repairs engine exhaust systems of all types of cars, trucks, boats, motorcycles, and stationary engines. DIRECTIONS FOR USE: 1. Clean off loose rust and dirt from the damaged area of muffler or tailpipe with sandpaper or a steel wire brush. Wear goggles as eye protection 2. Warm-up muffler, peel back the red overlay on both sides of bandage and then wrap the clear center around the damaged area- overlapping 10-15mm 3. Run the motor or drive for approximately 30 minutes. The heat from the exhaust chemically welds the epoxy in the bandage into one solid protective coating NOTE: For small repairs use Loctite Muffler Putty (MP2). When repairing large holes use a piece of sheet metal ie beer can, wired between the hole and the bandage as reinforcement. When assembling new pipes and mufflers use Loctite Exhaust Joint Sealer (JS1), It guarantees carbon-monoxide leakproof joints For large mufflers more than one bandage may be required

Read more less

White, metal-free, food-grade lubricant and anti-seize made from white oil and extreme pressure (EP) additives. H1 NSF Reg. No: 123004. LOCTITE® LB 8014 is a white, metal-free, food grade lubricant and anti-seize made from white oil and extreme pressure (EP) additives. It prevents friction, seizing and galling in stainless steel and other metal parts. It is temperature resistant to +400°C, has a 0 NLGI grade and is H1 NSF Registered; No: 123004.   Food grade lubricant and anti-seize Metal-free Temperature resistant to +400°C NLGI Grade 0 Prevents friction, seizing and galling in stainless steel and other metal parts H1 NSF Reg. No.: 123004   LB 8014™ prevents seizing, galling, friction, and wear on threaded joints and other metal-to-metal surfaces. It is a combination of white lubricating solids and extreme pressure lubricating agents in an aluminum gelled white oil. Typical applications include pipe joints, nuts, bolts and studs, flange gaskets, slip-fit, press-fit and keyed shafts, and metal-to-metal contact involving stainless steel and other stainless alloys. It is used in industrial food industries such as meat and poultry packing plants, dairy products processing plants, canning plants, grain processing plants, sugar processing plants, bakeries, beverage plants, breweries, hospitals, and other general plant maintenance. This product is typically used in applications with an operating range of -29 °C to +400 °C.   PRODUCT DESCRIPTION characteristics: Technology Anti-Seize Appearance Smooth white paste LMS Components One component - requires no mixing Cure Not applicable Application Lubrication Specific Benefits ● Lubricates, seals, and prevents galling in stainles steel joints and threaded connections ● Temperature resistant to 400 °C ● Metal free formulation   Directions For Use: 1. For best performance the mating surface should be clean and free of grease. 2. Apply thin coating to threads and flats of nuts and bolts, assemble. 3. Use full strength. Do not thin.

Read more less

WITHSTANDS HEAT UP TO 550°C Holes in mufflers, tailpipes, and engine pipes can be fixed immediately without dismantling Non-asbestos Hi-Temp Exhaust Repair Bandage is wet and ready to use when removed from the air sealed package. When hardened by exhaust heat, it turns into a hard, long lasting repair. DIRECTIONS FOR USE: 1. Clean off loose rust and dirt from the damaged area of muffler or tailpipe with sandpaper or a steel wire brush. 2. Remove bandage from the sealed foil packet and wrap the wet bandage around the damaged area with the specially impregnated material against the muffler or tailpipe, overlapping 10-15mm. 3. Support the wrapped bandage temporarily with the enclosed wire until it is heat cured. 4. Idle the motor in the open air for 20-30 minutes. The exhaust heat will harden it to a hard, protective coating.

Read more less

Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.

Read more less

Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.

Read more less

A heat resistant, solvent-based, flexible contact adhesive suitable for bonding both absorbent and non-absorbent surfaces. It forms an instant bond on contact of two surfaces. Features; Heat resistance up to 130C No clamping required Suitable for interior and exterior jobs Cured adhesive is resistant to dilute acids and alkalis Grabs immediately on contact Easy to spread Appearance: Yellowish to beige coloured opaque liquid with strong solvent odour. Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench or table tops Areas where clamping or pressing facilities are either not available or difficult to use Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Fixing shoes Fixing laminate to tables, benchtops etc Leather shoe and leather repairs, leather work eg handbags Repairing tents and outdoor equipment Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Attaching rubbers to your fridge door Repairing your wetsuit Some plastics such as vinyl sheeting and polystyrene are attacked by Kwik Grip Solvent. Test in an inconspicuous area prior to application. Seek the advice of vinyl flooring manufacturers prior to use with their products as discolouration and bubbling can occur with some types. If in doubt, Kwik Grip Advanced is safe to use for all these applications and will provide excellent bonding. Contains highly flammable solvents and care should be taken to ensure all fire precautions are observed. As an alternative, Kwik Grip Advanced is non-flammable. Not suitable for bonding rough, ill-fitting surfaces. (Consider the suitability of alternative products such as Liquid Nails for these applications). What materials is this product suitable for? Cork Rubber Felt Canvas Leather Metals Timber Laminated plastics (laminex, formica) Hardboard Compressed board How to use this product: When bonding laminated plastics, ensure that surfaces to be bonded are clean, dry and free from grease or paint. Surfaces to be bonded should be relatively smooth and/or close fitting. Both surfaces should be completely covered with adhesive and kept apart till “touch dry” – no more than 40 minutes. Position the items carefully, still keeping surfaces apart. Remember once joined they cannot be repositioned. When edges are perfectly aligned, press surfaces firmly together. Secure bond by running a roller over the bonded surfaces or else by hammering the surface from the centre outwards using a padded block. For bonding other materials, apply as for laminated plastics above. When small surface areas are to be joined a wet bond may be used. Simply apply Kwik Grip Solvent to one surface then bring the surfaces together and clamp until dry. Handy tips: -Care should be taken to test plastics prior to use as solvents present will attack some polystyrene and sheet vinyls. -Up to 5sq.m/litre (bonded area 2.5sq.m/litre) depending on the porosity of surfaces. -For vertical surfaces, we recommend using SELLEYS Kwik Grip Gel Vertical. -For applications in confined or low ventilation areas eg car interior, we recommend using SELLEYS Kwik Grip Waterbased, as it is non-toxic and free of fumes. -Use a brush, knife or serrated scraper for application. -When using the contact method REMEMBER bonding is immediate once the two surfaces are joined. -Keep container sealed when not in use. -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. -While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Kwik Grip Horizontal has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent. -Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips: -Ensure thorough ventilation when using. Avoid using in a confined space for prolonged periods. We recommend you use Kwik Grip Waterbased in these circumstances. -Highly flammable. Do NOT use in the same area as flame, fire or spark producing apparatus or machinery. -This product should not be accessible to juveniles, because of its solvent content. Intentional misuse by deliberately inhaling vapours from this product can be harmful or fatal. -Contact with skin and eyes should be avoided and avoid breathing vapour. -If in eyes flush with plenty of water for 15 minutes and seek medical advice. -If poisoning occurs, contact a doctor or Poisons Information Centre. Phone Australia 131 126 or New Zealand 0800 764 766. If swallowed, do NOT induce vomiting. Give a glass of water and seek medical advice. -For further information refer to the Safety Data Sheet (MSDS). Storage and re-use Store in a cool area away from ignition sources and out of direct sunlight.

Read more less

J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Mixed at a ratio of 1:1, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. At room temperature, J-B Weld sets in 4-6 hours to a dark grey colour. A full cure is reached in 15-24 hours. J-B Weld has a tensile strength of 3960 PSI and sets to a hard bond overnight. It can withstand temperatures up to 550ºF when fully cured. Great For: Household Repairs Automotive Plumbing Marine Crafts & More Strenght: 3960 PSI Set Time: 4-6 Hours Cure Time: 15-24 Hours Cure Colour: Dark Grey Use on: Automotive Brick Concrete Epoxy & Adhesives J-B Weld Metal Pro Sizes And More

Read more less

MarineWeld™ is a specially formulated two-part epoxy cold weld system that provides for strong, lasting repairs for bonding different or similar surfaces, such as aluminium, metal, composites, fibreglass and others. MarineWeld™ sets in 4-6 hours at room temperature and is fully cured to a dark grey colour in 15-24 hours. Once cured, it can be shaped, tapped, filed, sanded and drilled and will retain its strength above or below the waters' surface. MarineWeld™ has a 1:1 mixing ratio and tensile strength of 5020 PSI. GREAT FOR Boats Personal Watercraft In/Outboard Engines Deck & Hull Accessories USE ON Fibreglass Under Water/Wet And More STRENGTH 5020 PSI SET TIME 4-6 Hours CURE TIME 15-24 Hours CURE COLOR Dark Gray

Read more less

HighHeat™ is a hand mixable epoxy putty stick specifically formulated to bond and repair materials that will be exposed to high temperatures in automotive and industrial maintenance applications. It cures to a tough, hard bond with little to no shrinkage. This industrial-strength product outperforms conventional epoxy putties at high temperatures and sets in 1 hour at room temperature. After 8 hours, it can be drilled, tapped, machined, ground, filed and painted. HighHeat™ is rated at a tensile strength of 800 PSI and cures to a machine grey in color. It is able to withstand continuous heat exposure of 400ºF and intermittent heat exposure to 550ºF GREAT FOR Exhaust Manifolds Tail Pipes Mufflers Engine Blocks Duct Work Machinery High Temperature Projects USE ON Automotive Metal And More

Read more less

Bostik Contact Bond is a solvent based, high solids, brush or scaper grade contact adhesive. It is specifically formulated to provide an extra-strong and flexible bond on contact. Where to Use Residential Commercial Substrates Brush or Scraper Furniture and allied industries for fixing plastic laminates Flexible decorative surface coverings Materials Neoprene rubbers Porous and non-porous surfaces Wood MDF Particleboard Plywood Leather Felts Cottonback PVC Metal Features n-Hexane formula Safe quick drying Heat and water resistant Good brushability Excellent adhesion to porous and non-porous surfaces Provides an extra strong and flexible bond on contact Uses Bostik Contact Bond is a solvent based, high solids, brush or scraper grade contact adhesive. It is specifically formulated to provide an extra-strong and flexible bond on contact. It resists heat and water. It also provides excellent adhesion to most natural and neoprene rubbers as well as a wide variety of porous and non-porous surfaces. It may be easily applied by brush or scraper giving a secure and lasting bond making it clean and economical to use. Bostik Contact Bond is primarily used in the furniture and allied industries for fixing plastic laminates and rigid or flexible decorative surface coverings to wood, MDF, particle board, plywood, leather, felt, cotton back PVC and metal. PRODUCT CHARACTERISTICS Colour Pale yellow Viscosity Medium syrup Composition Polychloroprene rubber/resin Coverage 5 to 6m² per litre TYPICAL PERFORMANCE DATA (approx.) Touch dry Tube: 5 to 15 minutes Can: 20 to 30 minutes Full cure 45 minutes Solids content 22% Specific gravity 0.83 Heat resistance > 150°C DIRECTIONS FOR USE Read and understand the Safety Data Sheet before using this product. SDS can be acquired by visiting www.bostik.com.au or by scanning the relevant QR code on the pack. SURFACE PREPARATION Ensure all surfaces are clean and dry and free from all loose paint, dust, grease, oil and foreign materials. APPLICATION Tube (Blister Pack) Application 1. Unscrew cap and pierce and of the tube with the reverse end of the cap 2. Apply thin, even film to both surfaces to be glued 3. Leave until touch dry (approximately 5 to 15 minutes), then bring both surfaces together accurately 4. Take care to avoid the formation of air bubbles between surfaces 5. To ensure maximum adhesion, clamp or weigh down the entire surface or apply firm hand pressure evenly 6. Replace screw cap to keep the contents of tube airtight CLEANING To clean up tools, equipment and adhesive spills use Mineral Turpentine. Use Bostik Handy Wipe towels to remove adhesive from the skin. STORAGE AND SHELF LIFE Store in a cool dry place between 5°C and 30°C and out of direct sunlight. Keep away from sources of ignition. Shelf life is 12 months from the date of manufacture when stored as directed. VOC INFORMATION 606g/litre

Read more less

QuikSteel reinforced epoxy putty, 2 ounce Withstands up to 500 degree Fahrenheit temperatures Sets in 5 minutes, cures in 1 hour Hardens like steel, can be drilled, tapped, filed, sanded and painted Drinking water safe, NSF-61

Read more less

QuikSteel reinforced epoxy putty, 2 ounce Withstands up to 500 degree Fahrenheit temperatures Sets in 5 minutes, cures in 1 hour Hardens like steel, can be drilled, tapped, filed, sanded and painted Drinking water safe, NSF-61

Read more less