Heat Resistant

Show previous products

• 

  View options

  Loctite Loctite Muffler and Tailpipe Repair Bandage Withstands 260 degrees

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  IMPREGNATED WITH E-POX E RESIN WITHSTANDS HEAT UP TO 260°C Repairs engine exhaust systems of all types of cars, trucks, boats, motorcycles, and stationary engines. DIRECTIONS FOR USE: 1. Clean off loose rust and dirt from the damaged area of muffler or tailpipe with sandpaper or a steel wire brush. Wear goggles as eye protection 2. Warm-up muffler, peel back the red overlay on both sides of bandage and then wrap the clear center around the damaged area- overlapping 10-15mm 3. Run the motor or drive for approximately 30 minutes. The heat from the exhaust chemically welds the epoxy in the bandage into one solid protective coating NOTE: For small repairs use Loctite Muffler Putty (MP2). When repairing large holes use a piece of sheet metal ie beer can, wired between the hole and the bandage as reinforcement. When assembling new pipes and mufflers use Loctite Exhaust Joint Sealer (JS1), It guarantees carbon-monoxide leakproof joints For large mufflers more than one bandage may be required

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $7.23

  View options

• 

  View options

  Loctite Loctite LB 8014 Food Grade Anti-Seize Lubricant 8Oz

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  White, metal-free, food-grade lubricant and anti-seize made from white oil and extreme pressure (EP) additives. H1 NSF Reg. No: 123004. LOCTITE® LB 8014 is a white, metal-free, food grade lubricant and anti-seize made from white oil and extreme pressure (EP) additives. It prevents friction, seizing and galling in stainless steel and other metal parts. It is temperature resistant to +400°C, has a 0 NLGI grade and is H1 NSF Registered; No: 123004.   Food grade lubricant and anti-seize Metal-free Temperature resistant to +400°C NLGI Grade 0 Prevents friction, seizing and galling in stainless steel and other metal parts H1 NSF Reg. No.: 123004   LB 8014™ prevents seizing, galling, friction, and wear on threaded joints and other metal-to-metal surfaces. It is a combination of white lubricating solids and extreme pressure lubricating agents in an aluminum gelled white oil. Typical applications include pipe joints, nuts, bolts and studs, flange gaskets, slip-fit, press-fit and keyed shafts, and metal-to-metal contact involving stainless steel and other stainless alloys. It is used in industrial food industries such as meat and poultry packing plants, dairy products processing plants, canning plants, grain processing plants, sugar processing plants, bakeries, beverage plants, breweries, hospitals, and other general plant maintenance. This product is typically used in applications with an operating range of -29 °C to +400 °C.   PRODUCT DESCRIPTION characteristics: Technology Anti-Seize Appearance Smooth white paste LMS Components One component - requires no mixing Cure Not applicable Application Lubrication Specific Benefits ● Lubricates, seals, and prevents galling in stainles steel joints and threaded connections ● Temperature resistant to 400 °C ● Metal free formulation   Directions For Use: 1. For best performance the mating surface should be clean and free of grease. 2. Apply thin coating to threads and flats of nuts and bolts, assemble. 3. Use full strength. Do not thin.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $44.40

  View options

• 

  View options

  Loctite Loctite Exhaust Repair Bandage Withstands 550 degrees Ready To Use

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  WITHSTANDS HEAT UP TO 550°C Holes in mufflers, tailpipes, and engine pipes can be fixed immediately without dismantling Non-asbestos Hi-Temp Exhaust Repair Bandage is wet and ready to use when removed from the air sealed package. When hardened by exhaust heat, it turns into a hard, long lasting repair. DIRECTIONS FOR USE: 1. Clean off loose rust and dirt from the damaged area of muffler or tailpipe with sandpaper or a steel wire brush. 2. Remove bandage from the sealed foil packet and wrap the wet bandage around the damaged area with the specially impregnated material against the muffler or tailpipe, overlapping 10-15mm. 3. Support the wrapped bandage temporarily with the enclosed wire until it is heat cured. 4. Idle the motor in the open air for 20-30 minutes. The exhaust heat will harden it to a hard, protective coating.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $10.00

  View options

• 

  View options

  Selleys KwikGrip Water Based High Strength Multi-purpose Contact Adhesive Dries Clear 50ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $13.11

  View options

• 

  View options

  Selleys KwikGrip Water Based High Strength Contact Adhesive Dries Clear 500ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $40.93

  View options

• 

  View options

  Selleys KwikGrip Horizontal Contact Adhesive Heat and Water Resistant Broad Flat Surfaces 50ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  A heat resistant, solvent-based, flexible contact adhesive suitable for bonding both absorbent and non-absorbent surfaces. It forms an instant bond on contact of two surfaces. Features; Heat resistance up to 130C No clamping required Suitable for interior and exterior jobs Cured adhesive is resistant to dilute acids and alkalis Grabs immediately on contact Easy to spread Appearance: Yellowish to beige coloured opaque liquid with strong solvent odour. Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench or table tops Areas where clamping or pressing facilities are either not available or difficult to use Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Fixing shoes Fixing laminate to tables, benchtops etc Leather shoe and leather repairs, leather work eg handbags Repairing tents and outdoor equipment Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Attaching rubbers to your fridge door Repairing your wetsuit Some plastics such as vinyl sheeting and polystyrene are attacked by Kwik Grip Solvent. Test in an inconspicuous area prior to application. Seek the advice of vinyl flooring manufacturers prior to use with their products as discolouration and bubbling can occur with some types. If in doubt, Kwik Grip Advanced is safe to use for all these applications and will provide excellent bonding. Contains highly flammable solvents and care should be taken to ensure all fire precautions are observed. As an alternative, Kwik Grip Advanced is non-flammable. Not suitable for bonding rough, ill-fitting surfaces. (Consider the suitability of alternative products such as Liquid Nails for these applications). What materials is this product suitable for? Cork Rubber Felt Canvas Leather Metals Timber Laminated plastics (laminex, formica) Hardboard Compressed board How to use this product: When bonding laminated plastics, ensure that surfaces to be bonded are clean, dry and free from grease or paint. Surfaces to be bonded should be relatively smooth and/or close fitting. Both surfaces should be completely covered with adhesive and kept apart till “touch dry” – no more than 40 minutes. Position the items carefully, still keeping surfaces apart. Remember once joined they cannot be repositioned. When edges are perfectly aligned, press surfaces firmly together. Secure bond by running a roller over the bonded surfaces or else by hammering the surface from the centre outwards using a padded block. For bonding other materials, apply as for laminated plastics above. When small surface areas are to be joined a wet bond may be used. Simply apply Kwik Grip Solvent to one surface then bring the surfaces together and clamp until dry. Handy tips: -Care should be taken to test plastics prior to use as solvents present will attack some polystyrene and sheet vinyls. -Up to 5sq.m/litre (bonded area 2.5sq.m/litre) depending on the porosity of surfaces. -For vertical surfaces, we recommend using SELLEYS Kwik Grip Gel Vertical. -For applications in confined or low ventilation areas eg car interior, we recommend using SELLEYS Kwik Grip Waterbased, as it is non-toxic and free of fumes. -Use a brush, knife or serrated scraper for application. -When using the contact method REMEMBER bonding is immediate once the two surfaces are joined. -Keep container sealed when not in use. -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. -While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Kwik Grip Horizontal has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent. -Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safetytips: -Ensure thorough ventilation when using. Avoid using in a confined space for prolonged periods. We recommend you use Kwik Grip Waterbased in these circumstances. -Highly flammable. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Store in a cool area away from ignition sources and out of direct sunlight.

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $7.00

  View options

• 

  View options

  JB Weld JB Weld Steel Reinforced Epoxy Professional Size 283.6g

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Mixed at a ratio of 1:1, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. At room temperature, J-B Weld sets in 4-6 hours to a dark grey colour. A full cure is reached in 15-24 hours. J-B Weld has a tensile strength of 3960 PSI and sets to a hard bond overnight. It can withstand temperatures up to 550ºF when fully cured. Great For: Household Repairs Automotive Plumbing Marine Crafts & More Strenght: 3960 PSI Set Time: 4-6 Hours Cure Time: 15-24 Hours Cure Colour: Dark Grey Use on: Automotive Brick Concrete Epoxy & Adhesives J-B Weld Metal Pro Sizes And More

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $32.00

  View options

• 

  View options

  JB Weld JB Weld MarineWeld Epoxy Waterproof For Boats Fiberglass Aluminum

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  MarineWeld™ is a specially formulated two-part epoxy cold weld system that provides for strong, lasting repairs for bonding different or similar surfaces, such as aluminium, metal, composites, fibreglass and others. MarineWeld™ sets in 4-6 hours at room temperature and is fully cured to a dark grey colour in 15-24 hours. Once cured, it can be shaped, tapped, filed, sanded and drilled and will retain its strength above or below the waters' surface. MarineWeld™ has a 1:1 mixing ratio and tensile strength of 5020 PSI. GREAT FOR Boats Personal Watercraft In/Outboard Engines Deck & Hull Accessories USE ON Fibreglass Under Water/Wet And More STRENGTH 5020 PSI SET TIME 4-6 Hours CURE TIME 15-24 Hours CURE COLOR Dark Gray

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $22.00

  View options

• 

  View options

  JB Weld JB Weld HighHeat Temperature Resistant Epoxy Putty 57g

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  HighHeat™ is a hand mixable epoxy putty stick specifically formulated to bond and repair materials that will be exposed to high temperatures in automotive and industrial maintenance applications. It cures to a tough, hard bond with little to no shrinkage. This industrial-strength product outperforms conventional epoxy putties at high temperatures and sets in 1 hour at room temperature. After 8 hours, it can be drilled, tapped, machined, ground, filed and painted. HighHeat™ is rated at a tensile strength of 800 PSI and cures to a machine grey in color. It is able to withstand continuous heat exposure of 400ºF and intermittent heat exposure to 550ºF GREAT FOR Exhaust Manifolds Tail Pipes Mufflers Engine Blocks Duct Work Machinery High Temperature Projects USE ON Automotive Metal And More

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $25.00

  View options

• 

  View options

  Bostik Bostik Contact Bond Industrial Strength Adhesive Multi Purpose 50ml

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  Bostik Contact Bond is a solvent based, high solids, brush or scaper grade contact adhesive. It is specifically formulated to provide an extra-strong and flexible bond on contact. Where to Use Residential Commercial Substrates Brush or Scraper Furniture and allied industries for fixing plastic laminates Flexible decorative surface coverings Materials Neoprene rubbers Porous and non-porous surfaces Wood MDF Particleboard Plywood Leather Felts Cottonback PVC Metal Features n-Hexane formula Safe quick drying Heat and water resistant Good brushability Excellent adhesion to porous and non-porous surfaces Provides an extra strong and flexible bond on contact Uses Bostik Contact Bond is a solvent based, high solids, brush or scraper grade contact adhesive. It is specifically formulated to provide an extra-strong and flexible bond on contact. It resists heat and water. It also provides excellent adhesion to most natural and neoprene rubbers as well as a wide variety of porous and non-porous surfaces. It may be easily applied by brush or scraper giving a secure and lasting bond making it clean and economical to use. Bostik Contact Bond is primarily used in the furniture and allied industries for fixing plastic laminates and rigid or flexible decorative surface coverings to wood, MDF, particle board, plywood, leather, felt, cotton back PVC and metal. PRODUCT CHARACTERISTICS Colour Pale yellow Viscosity Medium syrup Composition Polychloroprene rubber/resin Coverage 5 to 6m² per litre TYPICAL PERFORMANCE DATA (approx.) Touch dry Tube: 5 to 15 minutes Can: 20 to 30 minutes Full cure 45 minutes Solids content 22% Specific gravity 0.83 Heat resistance > 150°C DIRECTIONS FOR USE Read and understand the Safety Data Sheet before using this product. SDS can be acquired by visiting www.bostik.com.au or by scanning the relevant QR code on the pack. SURFACE PREPARATION Ensure all surfaces are clean and dry and free from all loose paint, dust, grease, oil and foreign materials. APPLICATION Tube (Blister Pack) Application 1. Unscrew cap and pierce and of the tube with the reverse end of the cap 2. Apply thin, even film to both surfaces to be glued 3. Leave until touch dry (approximately 5 to 15 minutes), then bring both surfaces together accurately 4. Take care to avoid the formation of air bubbles between surfaces 5. To ensure maximum adhesion, clamp or weigh down the entire surface or apply firm hand pressure evenly 6. Replace screw cap to keep the contents of tube airtight CLEANING To clean up tools, equipment and adhesive spills use Mineral Turpentine. Use Bostik Handy Wipe towels to remove adhesive from the skin. STORAGE AND SHELF LIFE Store in a cool dry place between 5°C and 30°C and out of direct sunlight. Keep away from sources of ignition. Shelf life is 12 months from the date of manufacture when stored as directed. VOC INFORMATION 606g/litre

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $14.78

  View options

• 

  View options

  Blue Magic Blue Magic QuickSteel Steel Reinforced Epoxy Putty Metal Repair 57g

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  QuikSteel reinforced epoxy putty, 2 ounce Withstands up to 500 degree Fahrenheit temperatures Sets in 5 minutes, cures in 1 hour Hardens like steel, can be drilled, tapped, filed, sanded and painted Drinking water safe, NSF-61

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $15.00

  View options

• 

  View options

  Blue Magic Blue Magic QuickSteel Aluminum Reinforced Epoxy Putty Metal Repair 56.8g

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  QuikSteel reinforced epoxy putty, 2 ounce Withstands up to 500 degree Fahrenheit temperatures Sets in 5 minutes, cures in 1 hour Hardens like steel, can be drilled, tapped, filed, sanded and painted Drinking water safe, NSF-61

  Read more less

  Sold Out  Express Post: 1-3 Days | Standard Post: 2-5 Days

  $25.00

  View options

Back to top

Adhesives, sealants and tapes designed to maintain bond strength and integrity under elevated temperatures. Ideal for appliances, engine bays, lighting, ovens surrounds and sun-exposed installs. Compare continuous vs intermittent heat ratings, flexibility, and substrate compatibility (metal, glass, plastics). Use the filters to narrow by chemistry (epoxy, silicone, MS polymer), cure speed and application method. Always confirm the product’s maximum service temperature on the product page and TDS/SDS and follow surface prep and cure instructions.