Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$13.37
Seal leaks fast and protect exposed joins with Grunt Flashing Tape. This heavy duty self adhesive tape conforms to uneven surfaces, creates a long lasting waterproof barrier, and is ideal for quick fixes and preventative maintenance across roofs, gutters, and outdoor fixtures. Why choose this tape Weatherproof seal that helps stop water ingress at laps, seams, and penetrations. Strong tack for reliable adhesion on metal, plastic, and painted surfaces. Flexible backing that moulds to contours, ridges, and fasteners. UV and outdoor ready for Australian conditions. Clean finish suitable for temporary and permanent repairs. Common uses Sealing gutter joins, end caps, and mitres Flashing around skylights, flues, and vents Stopping drips at roof sheet overlaps Repairing small cracks in downpipes and rainwater fittings Protecting fasteners and exposed fixings from water General waterproofing on caravans, sheds, pergolas, and trailers Surface compatibility Works on most clean, dry, and sound substrates including coated metal roofing, painted timber, rigid plastics, fibreglass, and masonry that has been sealed. Not recommended for silicone contaminated surfaces or areas that remain permanently submerged. How to apply Prepare the area. Remove dust, old flaking coatings, oil, and loose rust. Dry the surface thoroughly. Measure and cut the tape to length with a knife or scissors. Peel and stick. Remove the release liner as you apply, pressing the tape down firmly. Roll with a hand roller or the back of a cloth to eliminate air pockets and ensure full contact. Overlap adjoining pieces by at least 25 mm for a continuous seal. Finish edges with extra pressure. Avoid applying in rain or onto wet surfaces. Pro tips For porous substrates, prime with a suitable primer and allow to dry before taping. Cold weather can reduce tack. Warm the tape and surface slightly to improve bond. Ensure water can shed over the tape rather than against the lap direction. Specifications Brand Grunt Product type Self adhesive flashing and sealing tape Size 50 mm width x 10 m length Use Exterior and interior repairs, roofs, gutters, and general waterproofing Application temperature Apply in dry conditions on clean and sound surfaces Cleanup Wipe tools with mineral turpentine or adhesive remover as suitable for the substrate Frequently asked questions Can I paint over itYes, most solvent based and acrylic paints will adhere. Test a small area first. Is it suitable for potable waterNot intended for potable water contact. Will it work on damp surfacesBest results are achieved on dry surfaces. Dry the area before application.
$15.20 $12.25
High strength, water based adhesive for carpet and cork Dunlop Multipurpose Carpet & Cork Adhesive is a water based, high strength adhesive designed for installing smooth or textured backed carpets and cork tiles. It delivers excellent wet grab and reliable bond on prepared subfloors. Suitable Surfaces Concrete Marine plywood Fibre cement sheet Key Features Water based and low odour High initial grab for reduced slippage Repositioning window up to 60 minutes Install immediately into wet adhesive for most carpets For cork or stiff backings, allow 10 to 15 minutes tack time before laying Coverage Approx. 2.5 m² per litre with a 3.2 mm V notch trowel Approx. 3.5 m² per litre with a 2.4 mm V notch trowel Application Ensure subfloor is dry, smooth, clean and protected from moisture. Prime highly porous concrete or timber before applying. Spread an even coat with the recommended V notch trowel. Lay carpet into the wet film. For cork or stiff backings, wait until the adhesive becomes tacky. Roll in both directions with a suitable drum roller to ensure full transfer. Set and Traffic Times No foot traffic for 24 hours Heavy traffic after 48 hours Avoid water and cleaning for 48 hours Clean Up Clean tools immediately with warm soapy water Remove dried residue with mineral turps Storage Shelf life up to 12 months in an unopened container stored at around 23°C. Good To Know Apply between 10°C and 30°C. Coverage varies with subfloor condition and trowel technique.
$54.95
Stop leaks fast with Fastfix Waterproof Repair Tape. This heavy duty, self-sealing tape forms a tough barrier that helps block water, air and moisture on a wide range of materials. Keep a roll in the toolbox, the ute or the caravan for quick fixes at home or on site. Creates a waterproof seal on clean, dry surfaces Extra thick backing with strong adhesive for a reliable hold Sticks to PVC, metals, plastics, rubber, vinyl, glass, ceramics and more Great for gutters, downpipes, garden hoses, pool gear, tents and tarps Easy to apply by hand with no special tools required Suitable for indoor and outdoor use Where it works Gutters and roof flashings Downpipes and irrigation fittings Garden hoses and pool hoses Camping gear such as tents and tarps Boat covers and awnings Plastic bins, storage tubs and general repairs How to use Clean and dry the area. Remove dust, oil and loose paint. Cut a piece of tape that overlaps the repair by at least 25 mm on all sides. Peel the liner and position the tape carefully. Avoid touching the adhesive. Press down firmly from the centre out to the edges to remove air bubbles. For higher pressure or larger repairs, apply a second layer with the seam offset. Allow time under firm pressure to achieve the best bond. Good to know Best adhesion on smooth, non-porous surfaces. Not a substitute for structural repairs. For wet or submerged applications, bond strength can vary depending on surface and water pressure. Test on a small area first if surface is delicate or freshly painted. Specifications Brand Fastfix Product type Waterproof repair tape Size 50 mm width x 5 m length Colour Black Adhesive Pressure-sensitive Finish Flexible, conformable backing Suitable environments Indoor and outdoor Storage Store cool and dry, out of direct sunlight. Keep liner on until use.
$21.52 $21.23
Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.
$27.85
Crommelin Pond Sealer Clear is a water-based, clear waterproofing membrane for sealing above-ground ponds, bird baths and ornamental water features, supplied here in a 1L pail. It goes on as a seamless coating and dries to a clear, low-sheen finish, so the look of the concrete, render or brickwork underneath is kept. It is designed to stay watertight under permanently wet conditions on structures that don't move.About the formulaA ready-to-use, water-based membrane that is non-toxic and safe for fish and plants. The manufacturer's technical data sheet also lists it as suitable for collecting or storing drinking water. It is UV stable, dries quickly and has excellent adhesion to porous cement-based surfaces. Repairs are easy, and tools wash up with water. It dries clear and hard, so it is meant for solid structures without joins, internal corners or expected movement. Where there are existing holes or cracks, or movement is expected, Crommelin recommends its Pond Sealer Colours membrane instead.Where to use itIndoors: ornamental water features, indoor fountains and other solid, porous water-holding features that won't flex.Outdoors: new or renovated above-ground fish ponds, bird baths, and ornamental water features built from concrete, render, brick or block.Suitable surfaces include concrete, cement render, brickwork, concrete blocks and other cementitious substrates. It is not suitable for non-porous surfaces.How to use itSurfaces must be clean, sound and completely dry, and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and laitance. Repair any loose or crumbly areas first with a suitable repair mortar. To check porosity, wet a small area. If it darkens, the surface is porous and can be sealed. If it doesn't, it is too dense to seal. Stir the sealer well before use and apply with a brush or roller. Apply when surface and air temperatures are between 10 and 35°C and humidity stays at or below 85%. First coat: mix equal parts sealer and water, then apply a thin, even coat. Allow about 15 minutes to dry. Second coat: apply un-thinned sealer over the surface and let it dry. Third coat: apply un-thinned sealer at right angles (90 degrees) to the first coat. Wash brushes and rollers in water before the sealer dries. Important notesRecoat after about 4 hours. Full cure takes about 7 days, and good airflow helps. Keep the coating away from moisture until it has fully cured, and protect it from damage before filling with water. Not suitable for use in chlorinated water. Do not apply it to non-porous surfaces. It is not intended for in-ground ponds or for structures with cracks or movement. Don't apply in extreme heat, cold or humidity. Coverage depends on how porous the surface is. As a guide, 1L produces about 2 to 4 square metres of finished coating.Specifications Brand Crommelin Product Pond Sealer Clear Pack 1L pail Colour Clear when dry, low-sheen finish Base Water-based membrane Application Brush or roller Recoat time About 4 hours Full cure About 7 days Coverage About 2 to 4 m² of finished coating per 1L, depending on surface porosity Application conditions 10 to 35°C, maximum 85% humidity Clean up Water, before the product dries Use Interior and exterior, fish ponds and ornamental water features SafetyStore in a cool, dry place. Follow normal good practice when handling: avoid contact with eyes and skin, wash hands after use, and keep out of reach of children. Crommelin supplies it on request. Refer to the Safety Data Sheet (SDS) for full details.
$30.14
Stop leaks fast with Gorilla Patch and Seal Tape. This ultra thick, flexible sealing tape conforms to rough, uneven, and curved surfaces to create a strong, watertight barrier. Ideal for emergency fixes and long term maintenance around the home, workshop, caravan, and boat. Why you will love it Instant waterproof seal helps stop leaks on contact Works above or below the waterline for pools, gutters, and marine jobs UV and weather resistant for outdoor use Conforms and stretches to seal gaps, cracks, and seams Sticks to many surfaces including PVC, metal, plastic, glass, tile, and more Great for Repairing pinholes and cracks in gutters and downpipes Patching above ground pool liners and inflatable pools Sealing roof sheets, skylights, flashings, and RV seams Fixing garden hoses, buckets, and water features Temporary window and greenhouse repairs Surface compatibility Material Suitable Notes PVC, ABS, most rigid plastics Yes Clean and dry for best bond Metal, aluminium, galvanized steel Yes Remove rust and loose paint Glass, glazed tile, ceramics Yes Degrease surface Rubber, EPDM, vinyl Yes Press firmly to conform Textured masonry, concrete Yes Fill deep voids first for a flat seal Silicone coated or oily surfaces No Adhesion is limited How to use Prep Clean and dry the area. For underwater patches, wipe away algae or loose debris. Measure Cut a piece that extends past the damage by at least 25 mm on all sides. Apply Peel the liner and place tape over the damage. Start from the centre and work outwards. Seal Press down hard, removing air bubbles. Use a roller or rounded tool for maximum contact. Cure Initial grab is immediate. Full bond strength improves over 24 hours. Tips for best results Round the corners of the patch to reduce lifting For high pressure leaks, apply a larger patch or multiple layers Do not apply over active flowing water without reducing the flow first Frequently asked Can I use it underwater Yes. It can be applied to wet surfaces and submerged areas. Clean the surface as well as possible for the best seal. Is it paintable Most tapes are not paintable. If appearance matters, trim neatly and paint the surrounding surface instead. Is it a permanent fix It provides a durable seal for many applications. For structural or critical repairs, consider a permanent fix when practical. Good to know Temperature use range typically suits most Australian conditions Store in a cool, dry place and keep the roll protected from dust Glues Australia keeps Australia together. If you need help choosing the right sealing solution for your job, contact our team.
$55.26 $38.48
Dulux Precision Maximum Strength Adhesion Primer Get a tough, reliable bond on hard to paint surfaces with Dulux Precision Maximum Strength Adhesion Primer. This water based, low odour primer works as a primer, sealer and undercoat, creating a strong foundation for acrylic or oil based topcoats on both interior and exterior projects. Why choose this primer Water based with low odour Excellent adhesion on glossy and hard to coat surfaces Suitable as primer, sealer and undercoat Interior and exterior use Fast drying: touch dry in 30 minutes, recoat in 1 to 2 hours Topcoat within 30 days for best results Ideal surfaces Tiles, high gloss enamels, varnished timber, uPVC, fiberglass, aluminium, galvanised steel, Colorbond, glass, glazed brick, laminates and previously painted glossy finishes. Key specs Finish Flat Colour White Coverage Up to 10 m² per litre per coat, depending on surface Dry time Touch dry 30 minutes Recoat time 1 to 2 hours Full strength 7 days after application VOC 30.4 g/L Application temperature Between 10°C and 32°C Clean up Water Pack sizes 1 L and 4 L How to use Prepare the surface so it is clean, dry and free of grease, wax, dust, loose paint and rust. Wash if needed and allow to dry. Stir thoroughly before and during use. Apply 1 even coat with a high quality brush, roller or spray. For very smooth surfaces 1 coat is usually sufficient. Allow 1 to 2 hours before recoating or applying the topcoat. Topcoat within 30 days. Application tips Do not tint for difficult surfaces. Thin only if necessary with a small amount of water. When using solvent based enamel topcoats, lightly sand the primer before applying the enamel. If using under products with strong solvents, let the primer dry 24 hours and test compatibility on a small area first. Where not to use Floors, benchtops or surfaces subject to standing water Below 10°C surface temperature or if conditions may drop below 10°C during drying Clean up and safety Clean tools with water and a mild detergent, then rinse. Ensure good ventilation during use. Wear eye protection and avoid skin and eye contact. Always follow label directions.
$49.88
Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.
$89.23
Key features Instant stick for quick, clean application Refill cartridge designed for the Bostik Glu Tape dispenser Neat roller action helps prevent lumps and smears Great for scrapbooking, school projects, cards, labels, and gift wrapping Transparent adhesive for a tidy finish Long length for multiple projects Best for Paper, card, photos, and lightweight craft materials Mounting, edging, and everyday office sticking jobs How to use Ensure surfaces are clean, dry, and free of dust. Open the dispenser, remove the empty cartridge, and click in the refill. Hold the roller at a slight angle and glide along the surface to apply adhesive. Press items together firmly for a secure hold. Good to know If you misplace a strip, gently lift before pressing down firmly. Store upright in a cool, dry place out of direct sunlight. Specifications Product type: Adhesive roller refill Length: 12 m Compatibility: Bostik Glu Tape dispenser Finish: Clear
$7.07
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$108.41
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. SafetyAvoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. Refer to the Safety Data Sheet (SDS) for full details.
$139.40
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. SafetyAvoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. Refer to the Safety Data Sheet (SDS) for full details.
$48.79
Dunlop Primer & Additive is a water-based multipurpose solution that improves the bond between porous substrates and adhesives, waterproofing membranes, or screeds. It can be used as a primer before tiling or as an additive to strengthen screeds and grouts. Surface Preparation: Ensure the surface is clean, dry, and free of dust, oil, wax, paint, or other contaminants. For new concrete or screeds, allow to cure completely. Fill cracks and voids using a patching compound. Application Instructions: As a primer, dilute 1 part Dunlop Primer & Additive with 3 parts water. Apply evenly using a brush or roller. Allow it to dry for at least 30 minutes before applying adhesives or membranes. As an additive, replace part or all of the mixing water in tile adhesives or grouts to improve flexibility and adhesion. Follow the manufacturer's recommended ratios. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Allow to dry for at least 30 minutes before overcoating. Drying may vary depending on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based acrylic polymer pH: Neutral Appearance: Milky white liquid Shelf Life: 12 months (unopened in cool, dry conditions)
$66.77
Feast Watson Outdoor Furniture Oil in Clear is a penetrating timber oil made to protect outdoor furniture while keeping the natural look of the wood, supplied here in a 1L can. It soaks into the surface rather than sitting on top, so it leaves a natural matt finish that lets the grain and texture show through.About the formulaAn oil-based, one-component formula enriched with eucalyptus oil. It is designed to resist mould and to give excellent water resistance, and the film is penetrating, so it is not expected to crack or flake. The Clear colour keeps the timber's own tone. It is not recommended for direct sunlight or extreme conditions. If you want a higher level of UV protection, choose one of the tinted colours in the range (Hardwood, Jarrah, Teak or Weathered Grey).Where to use itIndoors: not the intended use, as this oil is made for outdoor timber.Outdoors: timber outdoor furniture such as chairs, tables and benches, plus timber BBQ trolleys.Suitable for exterior timber furniture. Test a small, hidden area first if you are unsure how your timber will look.How to use itClean the furniture first with Feast Watson Woodclean to remove dirt, oil, wax and grease, then let it dry fully. Stir the oil thoroughly before and during use so the colour stays even. If you need more than one can, combine them in a larger container first. Apply the first coat with a quality brush, working in sections along the grain and fully coating edges and end grain. A roller or applicator pad can also be used. Let the oil soak in, then wipe off any excess with a brush or clean cloth. Leave it for 12 hours before applying a second coat. For chairs and benches, start on the inside of the legs, then move up to the seat and finish with the back. Clean brushes and tools with mineral turpentine.Important notesAllow about 12 hours between coats. Touch dry time is around 6 hours at 25°C and 50% humidity, and cooler or more humid conditions will take longer. Do not apply below 10°C, in very hot weather, or when rain or heavy dew is expected while the coating dries. Two coats are recommended, and the manufacturer lists a spread rate of about 6m² per litre, which varies with the timber. Over time, watch for colour loss, dryness and weathering. When that happens, clean with Woodclean and apply one maintenance coat. Soak used rags and cloths in water before disposing of them.Specifications Brand Feast Watson Product Outdoor Furniture Oil Size 1L Colour Clear Base Oil-based, with eucalyptus oil Finish Matt Application Brush, roller or applicator pad Coats 2 Recoat time 12 hours Spread rate About 6m² per litre Minimum application temperature 10°C Clean up Mineral turpentine Use Exterior timber furniture, BBQ trolleys and benches SafetyUse in a well-ventilated area and keep away from heat, sparks and open flame. Avoid contact with skin and eyes, and wear gloves and safety glasses while working. Keep out of reach of children and store the sealed can in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$74.61
Selleys Liquid Nails VP30 Primer is a rapid-curing, water-based priming concentrate designed as a bridging primer in the Liquid Nails timber flooring system, supplied here in a 1L pack. It is used on concrete slabs and other porous or non-porous surfaces before levelling compounds or flooring adhesives go on, and it flashes off in about 30 minutes so the next stage of the job can start quickly.About the formulaA water-based hybrid polymer primer that is low in VOCs and low in odour. It changes colour as it dries, going on pink and turning red when dry, so you can see at a glance when a coat is ready. Once cured it will not re-emulsify in water, and tools and splatter can be cleaned up with water before the primer cures.Where to use itIndoors: as a bridging primer between Selleys VBS or VBS Rapid moisture barrier and self-levelling compound on concrete slabs, or to prime concrete before self-levelling compound is poured as part of a timber flooring installation.Outdoors: not intended for outdoor use. It is an interior product.Suitable for clean, sound concrete slabs and other porous or non-porous surfaces that will be topped with adhesives or floor skimming and levelling compounds. Check compatibility with your chosen flooring products before starting.How to use itStart with a clean, sound, dust-free surface and stir the primer well before use. Cut in the edges with a brush, then apply with a roller, brush or broom. Allow for roughly 6 to 10 m² per litre, depending on how porous the surface is. Leave a continuous film on the surface so the next layer bonds properly. Pour the primer out onto the floor rather than leaving it in the container, which keeps it cool and gives you more working time. Make sure the primer has dried clear and can be walked on without tackiness before pouring self-levelling compound. Good ventilation helps it cure faster. Clean up with water before the primer cures.Important notesCure time is about 30 minutes, depending on conditions. Very porous concrete or slabs with high moisture content may need a second coat. If the coating soaks away or you see dull patches or pinholes, apply another coat once the first has cured. If you are priming over a moisture barrier, make sure it is fully cured first. Do not apply over dusty or contaminated surfaces, and do not use on surfaces that are subject to standing water. Brushes and rollers are best discarded after use.Specifications Brand Selleys Product Liquid Nails VP30 Primer Size 1L Colour Pink when wet, red when dry Base Water-based Application Brush, roller or broom Cure time About 30 minutes Coverage About 6 to 10 m² per litre, depending on surface Clean up Water, before curing Use Interior SafetyUse with normal care: work in a well-ventilated area, avoid contact with eyes and skin, and wear gloves and safety glasses. If product gets on skin, wash with plenty of soap and water, and if it gets in eyes, rinse cautiously with water for several minutes. Keep out of reach of children and store in a cool, dry place with the lid sealed. Refer to the Safety Data Sheet (SDS) for full details.
$48.95
Selleys Liquid Nails VBS Rapid is a two-part, water-based epoxy vapour barrier kit that seals concrete slabs before timber flooring goes down, supplied here as a 1.5L resin and hardener kit. Rolled onto a dry, stable slab, it helps block moisture vapour rising from the concrete into the floor above, and its fast-curing formula suits jobs where the flooring needs to go in quickly.About the formulaA pigmented, water-based epoxy supplied as separate resin and hardener components that are mixed together just before use. The colour-coded parts blend to a uniform green, so it is easy to see when the mix is ready, and it is normally applied as a single coat. It has a low odour and can be cleaned up with water while still wet. It is designed to bond well with Selleys Liquid Nails timber flooring adhesives such as Timberflex.Where to use itIndoors: over structurally sound, dry concrete floor slabs, as a moisture vapour barrier under timber flooring that is fixed with a compatible Selleys flooring adhesive.Outdoors: not intended for outdoor use.Suitable surface: clean, dry and stable concrete slabs. Very porous concrete or slabs with high moisture content may need a second coat.How to use itComplete all your preparation and mark out the work area before you start mixing, because this product cures quickly. The slab must be clean, dry and sound, and free of curing compounds, oil, grease, wax, sealers, old coatings and adhesives. New concrete should have cured for at least 28 days or until its moisture content is below 5.5%. Mix the components thoroughly until the colour is even, with no streaks. Tip the mix onto the slab straight away rather than leaving it in the pail, then roll it on with a short-nap mohair roller and cut in the edges with a brush. If a second coat is needed, apply it after the first has cured and before 24 hours have passed. Clean tools with water before the product cures.Important notesDo not apply over damp or contaminated surfaces, or when the temperature is below 10°C or above 35°C. Cure time is rapid and the film is tack-free within hours, but allow for conditions on site such as temperature and slab porosity. Check coverage against your slab: Selleys states roughly 6 to 8 m² per litre per coat. This product is a vapour barrier system, not a flooring adhesive, so use a compatible flooring adhesive over the cured coating.Specifications Brand Selleys Product Liquid Nails VBS Rapid Vapour Barrier Pack 1.5L two-part kit (resin and hardener) Colour Green when mixed Base Two-part water-based epoxy Application Roller, with brush for edges Cure Rapid, tack-free within hours Coverage About 6 to 8 m² per litre per coat Application temperature 10°C to 35°C Clean up Water (before curing) Use Interior, over concrete slabs SafetyUse with normal care: work in a well-ventilated area, avoid contact with skin and eyes, and wear gloves and safety glasses. Keep out of reach of children and store the unused components sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$93.26
Bondall Betta Tilecare Shower Sealer is a clear, penetrating sealer that helps waterproof unglazed tiles and grout in showers and other wet areas, supplied in a 500ml pack. It soaks into the surface rather than sitting on top, so it protects without leaving a slippery film. It is made in Australia by Bondall and suits DIYers who want a simple, invisible finish.About the formulaA transparent, penetrating sealer based on silane chemistry. It leaves an invisible water-repellent finish with a non-slip feel, and the cured surface resists standard household chemicals. The same product is also sold under the Bondall TileGuard Shower Sealer name.Where to use itIndoors: shower walls and floors, bathroom tiling and grout, and other wet areas where the tiles and grout are unglazed.Outdoors: not specifically promoted by the manufacturer for outdoor use, so check the label before using it outside.Suitable surfaces include most unglazed tiles and grout, such as terracotta, ceramic, marble and slate.How to use itRemove old silicone strips and soap build-up first. Clean off mould using a mould cleaner or bleach, then rinse thoroughly with water. Repair or patch any loose or missing grout. Let the area dry for about 12 to 24 hours before sealing, or 3 to 4 days if the surface is porous or has just been high-pressure washed. Test a small, inconspicuous spot first. Apply with a paint brush, roller or pump spray, working evenly and avoiding pooling or heavy over-application, especially on pitted surfaces. If the product runs, wipe it back with a clean, dry, low-lint cloth. The manufacturer lists a 15 minute recoat time and 24 hours for a full dry.Important notesNot suitable for glazed surfaces. It is not designed to waterproof a water-holding vessel, such as a pot used as a fish pond. Grout should be in sound condition, as the sealer will not cover hairline cracks. It does not fix structural or plumbing defects in a shower, so refer those to the appropriate trade. Treat stains, moss and mould before sealing. Reviewers have reported staining on painted tiles with related Bondall sealers, so always test first.Specifications Brand Bondall Product Betta Tilecare Shower Sealer (also sold as TileGuard Shower Sealer) Pack 500ml Colour Transparent Chemistry Silane Application Paint brush, roller or pump spray Recoat time 15 minutes Full dry 24 hours Coverage 1L covers 5 to 10 m2 Use Unglazed tiles and grout in wet areas Origin Australian made and owned SafetyUse in a well-ventilated area, and wear a suitable respirator if spraying. Wear gloves and eye protection. On skin, wash the area well with running water. For eye contact, flush with running water for several minutes and see a doctor. Refer to the Safety Data Sheet (SDS) for full details.
$27.14
![Davco K10 Plus Waterproofing Membrane 20L [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/davco-k10-plus-waterproofing-membrane-20l-grey-2.jpg?v=1792411411&width=645)
Davco K10 Plus is a premixed, ready-to-use, water-based polyurethane waterproofing membrane for tradies and builders, supplied here as a 20L pail in grey. It is a Class III membrane designed to sit under tile, stone and other resilient finishes on both walls and floors, in domestic and commercial jobs.About the formulaA one-part, water-based polyurethane that goes on straight from the pail with no mixing. It is rated Class III under AS/NZS 4858 and is highly flexible, with elongation above 500%. The manufacturer also lists it as non-toxic, UV stable and suitable as an anti-fracture membrane. Because it is water-based and solvent-free, it suits confined areas. Published technical figures include a Shore A hardness of 72 and a tensile strength of 2.1MPa.Where to use itIndoors: walls and floors in showers, bathrooms and other wet areas, ahead of tiling.Outdoors: terraces, balconies, roofs and walkways that will be covered with a hard finish such as tile.Suitable substrates include concrete, cement render and screeds, lightweight blocks, building boards approved for wet areas (such as compressed fibre cement sheet) and prepared metal surfaces. Metal needs an etching primer. All substrates should be primed with a suitable Sika primer before the membrane goes on.How to use itPrepare the substrate so it is sound, clean and primed. New render or screed needs a wood float finish and should cure before you start. Where falls are not already in place, form them with a sand and cement screed first. Apply the membrane by brush or roller in a minimum of two coats to reach a 1mm dry film. Each coat should go on at a wet film thickness of at least 0.75mm. Let the first coat dry for about 1 to 2 hours, then apply the second coat at 90 degrees to the first. Add further coats if needed to reach the minimum dry film thickness. Tools can be cleaned with water while the product is still wet. Tile over the cured membrane using a Sika polymer-modified cement-based tile adhesive.Important notesAllow about 6 to 8 hours before tiling or applying other finishes. Allow 3 days before flood testing and 5 days before the area returns to service. Drying times vary with temperature, humidity and film thickness. The membrane is not designed to be left exposed, so it must be covered with a finish. Follow the current Sika data sheet for primer selection, bond breakers, corners and joints, and for any movement joints. Wet area waterproofing must be done to the relevant Australian Standards and building code requirements, so use a licensed applicator where required. Shelf life is 12 months from manufacture. Store in a cool, dry place out of direct sunlight and do not let it freeze.Specifications Brand Davco (Sika) Product K10 Plus Waterproofing Membrane Pack 20L pail Colour Grey Base Water-based polyurethane, one part, premixed Classification Class III (AS/NZS 4858) Application Brush or roller Elongation Greater than 500% Coverage Approx. 13.3m² per 20L pail at two coats (1mm dry film) Recoat time 1 to 2 hours Ready for tiling 6 to 8 hours Flood test After 3 days Return to service 5 days VOC content 62g/L Shelf life 12 months from manufacture Use Interior and exterior, under tile, stone and other resilient finishes SafetyEven so, wear gloves and eye protection during application and keep the area ventilated, especially in enclosed spaces. Keep out of reach of children, avoid contact with eyes and skin, and do not let uncured product enter drains or waterways. Store the pail sealed, cool and out of frost. Refer to the Safety Data Sheet (SDS) for full details.
$266.99
Gripset Betta Damp Stop is a one-part waterproofing primer and protective coating that helps hold back rising damp and moisture vapour moving through concrete, masonry and other porous mineral surfaces, supplied here in a 1L size. It suits renovators, tradies and confident DIYers who need a straightforward damp barrier under floor finishes, membranes and adhesives without mixing two parts together.About the formulaDamp Stop is a single-component, moisture-curing liquid in a light yellow colour. Because there is nothing to mix, you avoid the wasted product and short pot life that come with two-part epoxy primers. It is solvent free and odourless, so it can be used in confined areas. Once it has dried, it can be overcoated with other paints, coatings and adhesives. It also works as a dust-binding treatment for aged cement floors and dusty screeds.Where to use itIndoors: sealing the inside faces of cellar and basement walls against moisture vapour and dampness, priming floors ahead of membranes or finishes, protecting timber flooring, carpet and vinyl from rising damp, and stabilising dusty or aged screeds before floor finishes go down.Outdoors: priming external floors before a membrane is applied, and sealing the inner face of underground walls against residual moisture. The manufacturer lists it as suitable for internal, external, underground and immersed applications, and for resisting negative hydrostatic pressure.Suitable surfaces include concrete, cement mortar, renders and screeds, concrete and clay bricks, dense concrete, self-levelling compounds, compressed fibre cement sheet, fibre reinforced concrete, timber floorboards and sanded timber, and Hebel or other aerated concrete. For very porous, absorbent surfaces, or for metal and other smooth, shiny surfaces, the manufacturer points to other products in its range.How to use itStart with a clean surface, free of dirt, residues and old coatings. The surface can be damp but must have no surface water. Stir the product lightly, then apply with a short nap roller or short bristle brush. Leave 3 to 6 hours between coats and put the second coat on in the opposite direction to the first. Wait at least 24 hours, and make sure the primer is completely dry, before applying finishing membranes, coatings or adhesives.For high-build repairs, the manufacturer says to mix dry fine sand with the resin at about 3 parts sand to 1 part resin. Use a spatula for areas deeper than 1mm and keep the build to no more than 3mm.While still wet, tools can be cleaned with ethanol, methylated spirits or alcohol-based cleaners. Once dry, it has to be removed mechanically.Important notesDo not use over wet surfaces. Do not leave Damp Stop exposed as a finished membrane or sealer, as it is a primer. Do not apply when the surface temperature is below 10°C or above 35°C. Because it cures with moisture, cool or dry conditions can slow drying. The quoted drying times are tack free in 2 to 4 hours and dry film (ready to overcoat) in 24 hours, based on 20°C and relative humidity above 60%.Specifications Brand Gripset Betta Product Damp Stop Waterproofing Primer Size 1L Colour Light yellow Type One-component, moisture-curing liquid primer Solvent content Solvent free, odourless Application Short nap roller or short bristle brush Coverage (vapour barrier primer) About 6 to 8 m² per litre Coverage (negative pressure / moisture) About 3 to 4 m² per litre Coverage (dusty screeds, aged concrete) About 6 m² per litre Recoat time 3 to 6 hours between coats Tack free 2 to 4 hours Dry film (ready to overcoat) 24 hours Application temperature 10°C to 35°C surface Use Interior, exterior, underground and immersed SafetyEven so, avoid contact with eyes and skin, wear gloves and eye protection while applying, and keep it out of reach of children. Store the container sealed, away from direct heat and frost. Dispose of leftover product and empty containers in line with local regulations. Refer to the Safety Data Sheet (SDS) for full details.
$75.79
Davco Lanko 752 Bondit is a white PVA emulsion that does three jobs on site: it works as a mortar additive, a primer and a sealer, and it can also bond timber to timber. This 5L pack suits renderers, tilers, concrete patchers and joiners who want one economical product for strengthening cement-based work. Mixed into sand and cement mixes, it lifts adhesion, flexibility, tensile strength and impact resistance. It also improves the flexural and compressive strength of the mortar.About the formulaBondit is a PVA-based emulsion supplied ready to use, and you add it to your mix or dilute it with water depending on the job. Beyond strengthening mortars, it can be thinned and applied to concrete to prime, dustproof and seal the surface. Used neat, it can also be applied to timber joints as a PVA wood bond.Where to use itMortar additive: sand and cement mixes for concrete patching and for rendering, and mortars for tiling over concrete, render, blockwork and rendered brickwork.Bonding slurry: mixed into neat cement to bond new sand and cement toppings onto concrete.Primer and sealer: diluted with water and brushed or rolled onto concrete to prime, dustproof and seal.Joinery: applied neat to bond timber to timber.Suitable surfaces include concrete, render, blockwork, rendered brickwork and timber. Very porous surfaces should be primed with Bondit first. Always test for suitability on a small area before starting the full job.How to use itSurfaces should be dry, structurally sound and clean, and free of dust, dirt, wax, oil, grease, paint, adhesives and other contaminants. New concrete needs to cure for six weeks and have a wood float finish. Steel-trowelled concrete should be acid etched or wire brushed before tiling. New render should cure for at least 7 days.As a mortar additive, the manufacturer's guide is approximately 750 mL to 1 L of Bondit, plus the required water, for each 20 kg of sand and cement mix.As a primer, dilute with water and apply by brush or roller. Expect roughly 6 to 8 m² per litre when diluted.For joinery, apply neat by brush or roller. Expect roughly 3.5 m² per litre, depending on surface porosity and site conditions.Important notesDo not use Bondit in temperatures above 40°C or below 5°C.It is not suitable for permanently wet or damp areas such as swimming pools and spas. For those installations, the manufacturer recommends Davco Lanko 751 Lankolatex instead.Coverage figures are approximate and vary with surface porosity and site conditions.Store in the original, unopened and undamaged packaging in dry conditions between 4°C and 35°C. Shelf life is 12 months.Specifications Brand Davco (Lanko range) Product Lanko 752 Bondit PVA Additive Pack 5L Colour White Base PVA (polyvinyl acetate) emulsion Application Mixed into mortar, or applied by brush or roller Coverage (neat, joinery) Approximately 3.5 m² per litre Coverage (diluted, priming) Approximately 6 to 8 m² per litre Mortar dosage Approximately 750 mL to 1 L per 20 kg sand and cement mix Application temperature 5°C to 40°C Shelf life 12 months, unopened Storage Dry, 4°C to 35°C, original sealed packaging SafetyUse with adequate ventilation, and wear chemical-resistant gloves when handling. Do not eat, drink or smoke while using it, and follow standard hygiene practice. Keep the container tightly closed in a dry, well-ventilated place. Refer to the Safety Data Sheet (SDS) for full details.
$78.10
Bondall Ranex Rustbuster Gel is a thick, clingy rust converter and stain remover in a 250ml pack, made for treating rusted steel and iron before priming and painting. Instead of just masking rust, it reacts with it and turns it into a stable iron phosphate layer, so the metal is ready for an oil-based primer. It is an Australian made and owned product from the Ranex range.About the formulaThis is a phosphoric acid based gel. Because it is thick, it stays where you put it and keeps working for longer than a thin liquid would. That extra contact time helps it get into deeper rust. The gel clings to vertical, angled and textured surfaces as well as flat ones. It converts rust into iron phosphate, which forms a protective film that helps resist new rust. The same gel can also be used briefly as a stain remover on tarnished metal and on bore water and tannin stains.Where to use itRust conversion: rusted steel, wrought iron and other ferrous metals that need to be treated and primed before painting.Stain and tarnish removal: stainless steel, chrome, brass and copper, plus bore water and tannin stains. Test on a small hidden spot first.Suitable materials include rusted steel, wrought iron and other ferrous metals, and, for short-contact cleaning, stainless steel, chrome, brass and copper. Avoid Colorbond, painted surfaces, dry concrete, antifouling paint, marble, and anodised, zincalume or galvanised surfaces.How to use itWear gloves and suitable protective clothing, and test on a small, hidden area first.Prepare: Wire brush the rusted area to remove loose scale, oil, grease and old paint. A degreaser before brushing helps with stubborn contamination. You want clean, exposed rust. Mask or cover nearby surfaces that must not be touched by the gel, such as paintwork, Colorbond, marble and galvanised metal, using painter's tape and drop cloths.Rust conversion: Brush or roll the gel onto the rusted areas only. The surface should look dark and wet, and heavy rust needs a thick coat. Wipe any spills on surrounding paint or clean metal off straight away with a damp cloth. Leave the gel in place and do not wipe or wash it off while it works. Most jobs need 1 to 4 hours. Heavily rusted areas may need longer or a second coat, and you should wait 4 hours before re-treating. When the treated area has turned darker, finish with an oil-based primer. If residue is left on the surface, wipe it with a damp cloth and dry it.Stain removal: Brush the gel onto the stain and work it in. Leave it for a few minutes, or up to 15 to 20 minutes for heavier stains. Do not leave it on for long periods when cleaning stains. Wipe it away with a clean dry cloth, then use a damp cloth for any residue. Clean tools and spills with water and detergent.Important notesDo not use zinc-rich or water-based primers over this gel, because they are not compatible. Use it only on rusted areas and keep it off paintwork and non-rusted metal. The gel reacts on contact, so read the full directions before starting. Treated metal should be primed and painted for lasting protection. Coverage depends on the surface and how bad the rust is.Specifications Brand Bondall Product Ranex Rustbuster Gel Rust Converter Size 250ml Base Phosphoric acid solution (gel) Application Paint brush or roller Rust conversion time Typically 1 to 4 hours (allow 4 hours before re-treating) Stain removal contact time A few minutes, up to 15 to 20 minutes for heavy stains Coverage Up to 1 to 2 sqm per 250ml, depending on surface and rust severity Topcoat compatibility Oil-based primer only Clean up Water and detergent Origin Australian made and owned SafetyThis is a phosphoric acid based product and the manufacturer says it reacts on contact, so handle it with care. Wear gloves and other suitable protective clothing, and add eye protection when working with it. Keep it off skin, eyes and sensitive surfaces, and read the safety directions on the pack before use. Store it in its original container, out of reach of children. Always check the manufacturer Safety Data Sheet for hazard classification, first aid and storage details.
$30.17
Bondall Ranex Rustbuster is a fast-working rust treatment that converts rust into a stable iron phosphate layer, here in a handy 250ml bottle for tools, bikes, boats and household jobs. It does double duty as a rust converter before painting and as a cleaner that lifts surface rust, tarnish and bore water stains from polished metal and other non-porous surfaces.About the formulaA clear, phosphoric acid based liquid that penetrates rust and chemically changes the damaging iron oxide into a beneficial phosphate of iron. Because it destroys the rust rather than just covering it, rust-inhibiting paints are not needed over the treated area. It will convert existing rust but does not stop rust returning, so treated metal that is left uncoated can rust again. It is also used to brighten stainless steel, chrome, brass and copper.Where to use itIndoors: baths, basins and toilets, and other non-porous surfaces marked by rust, bore water or mineral stains.Outdoors: bikes, hand tools, boats, fittings and other rusted metal around the yard, workshop or marina.Suitable for rusted steel and iron, stainless steel, chrome, brass and copper, plus non-porous surfaces with rust or bore water stains (spot test first on anything you are unsure about, including tinted gelcoat).How to use itAlways wear gloves, protective clothing and eye protection.Rust conversion: remove oil, grease, paint and loose scale first. Apply Ranex to the rusted areas only, by brush, roller, rag or dipping, and let it dry without wiping it off so it can work into the rust. Drying takes anywhere from 1 to 24 hours depending on the application and conditions. Wipe any excess off surrounding metal or paintwork with a damp cloth straight away. Deep-seated rust may need a second coat after 24 hours. Once completely dry, topcoat with an oil-based primer and paint. Zinc-rich paints are not recommended.Surface rust and tarnish: apply with a damp cloth, sponge or fine steel wool, then wipe off promptly and polish with a dry cloth. Small rusty parts can be soaked for a few minutes and checked until clean, then wiped or washed off.Stains: work it into the stain, then wipe off. Do not leave it sitting on the surface.Clean up tools and drips with detergent and water.Important notesNot suitable for vehicle paintwork, Colorbond, dry concrete, anti-fouling paint, marble, or anodised, Zincalume and galvanised surfaces. The product reacts chemically on contact, so read the label directions before starting. Ranex converts rust but does not prevent it from forming again, so prime and paint the treated surface for lasting protection.Specifications Brand Bondall Product Ranex Rustbuster Rust Converter Size 250ml bottle Colour Clear liquid Base Phosphoric acid Application Brush, roller, rag or dipping Drying time 1 to 24 hours, depending on application Coverage Up to 20m2 per litre, depending on the surface Primer Oil-based primer recommended before painting Clean up Detergent and water Use Interior and exterior SafetyCorrosive. Wear protective gloves, protective clothing and eye or face protection, avoid breathing mist or vapour, wash skin thoroughly after handling, and do not eat, drink or smoke while using. For eye contact, rinse with water for at least 15 minutes and get medical help. Keep in the original container with the lid closed, and keep away from strong bases, oxidising agents and metals, as contact with common metals can release flammable hydrogen. Refer to the Safety Data Sheet (SDS) for full details.
$20.97
Crommelin DiamondTough Stone Shield Clear Sealer is a premium waterborne sealer made for dense natural stone, supplied here in a 1L pack that suits benchtops, feature walls and smaller floor areas. It protects against stains and water, dries clear, and leaves a natural to low sheen finish. Crommelin previously sold it as DiamondCoat Stone Shield. The brand says only the name has changed, not the product.About the formulaA water-based sealer that both penetrates the surface and forms a thin protective film, while still letting the stone breathe. It resists staining and abrasion and repels water well. It also contains an anti-microbial additive that helps stop mould and algae growing on the sealed surface. It is low odour and low VOC, dries quickly, and can be recoated soon after the first coat. It can be applied to vertical and horizontal surfaces.Where to use itIndoors: dense stone floor and wall tiles, stone and concrete benchtops, kitchens and living areas, and polished concrete.Outdoors: natural stone cladding and other exterior dense stone surfaces that suit a clear, low sheen protective coat.Suitable surfaces include granite, marble, bluestone, travertine, porcelain, polished concrete, terracotta, reconstituted stone and natural quarry stone. Always test a small patch first to check the colour enhancement, finish and slip resistance.How to use itThe surface must be clean and fully dry before you start. Crommelin requires a moisture test every time. If the surface has been acid etched, neutralise and rinse it thoroughly first. Apply the first coat evenly with a clean, lint-free tool so the surface is wet but no white excess liquid is left standing. Suitable tools are a brush, a roller, a lambswool applicator, a lint-free cloth or an airless sprayer. Apply the second coat in the same way once the first is touch dry, and within 2 hours. On very dense surfaces such as polished marble, the sealer may only need to be wiped on. If streaky film builds up on a dense surface once dry, wash it with warm soapy water, rinse and buff with a soft cloth. Clean tools with warm water and a little detergent straight after use.Important notesDo not apply when it is too hot or cold, when humidity is high, or when rain is expected within 48 hours. Allow about 24 hours before light foot traffic. Full cure takes around 7 days. Over-applying can leave a visible film on very dense stone, so work thinly and use a test patch to confirm the right rate. This product is a clear sealer. It cannot be tinted.Specifications Brand Crommelin Product DiamondTough Stone Shield Clear Sealer Pack 1L pail Colour Clear when dry Base Waterborne Finish Natural to low sheen Application Brush, roller, lambswool applicator, lint-free cloth or airless spray Recoat As soon as the first coat is touch dry, within 2 hours Light foot traffic About 24 hours Full cure About 7 days Application temperature 5 to 35°C Coverage Roughly 10 to 30 m² per litre, depending on how dense the surface is Primer required No Tintable No Use Interior and exterior SafetyEven so, avoid contact with skin and eyes, avoid breathing spray mist, and wear suitable protective clothing, gloves and eye protection when spraying. Keep the container sealed and store it in a cool, dry place. Keep it out of reach of children, and do not let it enter drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$49.55
SikaBond-105 ContactFix is a premium, high strength contact adhesive from Sika, supplied here in a 500mL can for laminate fabrication, upholstery and general sheet bonding. It is a one-component adhesive that dries quickly and gives a strong bond that stands up to heat and moisture, which makes it a practical pick for workshop and trade jobs.About the formulaA one-component polychloroprene (synthetic rubber) contact adhesive. It has a short flash-off time, high initial strength and good resistance to ageing, with a broad adhesion range across common sheet and covering materials. The manufacturer lists a tack-free time of roughly 5 to 8 minutes and heat resistance up to 90°C.Where to use itIndoors: fixing plastic laminates to timber, MDF or particleboard, and covering furniture and joinery with fabric, vinyl or foam.Vehicles and upholstery: Sika lists room-temperature contact bonding of covering materials such as PUR foams and textiles, plus steps, wheel arches, seat brackets and side walls. It also suits cover trims and edging profiles that spring back strongly, and auto and furniture upholstery.Suitable materials include timber, rubber sheets, plastic laminates, fabric, cloth-backed and polyester-backed vinyl, MDF, particleboard, concrete, glass and metal sheets. Test on your actual materials and conditions first to confirm adhesion and compatibility.How to use it Make sure both surfaces are sound, clean, dry and free of dirt, oil, grease, loose coatings and friable material. Apply an even coat to both surfaces. Earlier Sika data sheets list a roller coater, tooth comb, brush or spray gun as suitable methods. Let the adhesive dry until it is tack free (about 5 to 8 minutes, depending on conditions), then bring the surfaces together firmly with strong, even pressure. Take care with positioning, because contact adhesives bond on first contact. Clean tools and equipment while the adhesive is still uncured, using Sika Remover-208, Sika Colma Cleaner or another suitable solvent. Important notesDo not use in temperatures below +10°C or in condensing conditions. For best results, apply at ambient, material and adhesive temperatures within the range stated on the Sika data sheet. Store unopened in the original packaging, dry and out of direct sunlight, between +5°C and +25°C. Shelf life is 12 months from the date of production. Always test compatibility on the real substrates before committing to a full job.Specifications Brand Sika Product SikaBond-105 ContactFix High Strength Premium Contact Adhesive Pack 500mL can Colour Light amber (per current Sika data sheet) Base One-component polychloroprene Density 0.81 kg/L Solids content About 17% by mass Viscosity 350 mPa.s Tack-free time About 5 to 8 minutes Consumption 6 to 8 m² per litre Temperature resistance Up to 90°C Shelf life 12 months from production Clean up Sika Remover-208, Sika Colma Cleaner or other suitable solvent SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Use only outdoors or in a well-ventilated area, avoid breathing vapours, and wear protective gloves, protective clothing and eye or face protection. If it gets on skin, remove contaminated clothing and rinse with water. For fires use alcohol-resistant foam, carbon dioxide or dry chemical, not water. Refer to the Safety Data Sheet (SDS) for full details.
$28.77
Bondall Betta Tilecare Wet Area Waterproofer is a fast-curing, water-based liquid rubber membrane for sealing wet areas beneath tiles and renders, supplied here in a 10L pail for bigger bathroom, laundry and balcony jobs. It dries to a flexible, elastic film that acts as a water and vapour barrier, and it is designed to cope with permanently wet conditions, including ponding water once cured.About the formulaA water-based, one-part elastomeric membrane that is described by the manufacturer as non-toxic and non-flammable. It is classed as a Class III membrane under AS/NZS 4858 and, when used with the Betta detailing range, is designed to meet the Australian wet area requirements including AS 3740. The fast-curing formulation lets you tile or render over it quickly, and it is compatible with a range of tile adhesives, renders and toppings. No primer is needed on plasterboard or sound, dry concrete.Where to use itIndoors: bathroom and laundry floors and walls, shower recesses and other tiled wet areas, plus under screeds and toppings.Outdoors: balconies, decks, podiums and terrace floors, planters and retaining walls, and roofs that will be covered with screeds or toppings.Suitable substrates include concrete, screeds, renders, brick, plasterboard, fibre cement sheet and marine plywood. It sits under ceramic, porcelain, granite, marble and other stone tile finishes. Other surfaces, such as smooth, dense or damp ones, may need a Betta primer first, so check the technical data sheet for your substrate.How to use itMake sure the surface is sound, stable, clean and free of dust, oil, grease and loose material. Install the bond breaker and elastic joint band detailing first, as this is part of meeting AS 3740. Apply by brush, roller or spray unit in a minimum of two coats, changing direction between coats, to a total minimum coverage of 1.5 litres per square metre. This builds a dried film of roughly 1.2mm. Vertical or pitched areas can be done at around 1 litre per square metre. Take the membrane up walls at least 150mm in general wet areas and to 1.8m in shower recesses, finishing with a continuous, seamless film. Clean tools with water straight after use.Important notesTypical drying times at normal conditions (about 20°C, 50% humidity): tack free in about 45 minutes, recoat in about 1 hour, and ready to tile or topping over in about 4 hours. Retailer information quotes 6 hours before tiling, so allow the longer time in cool or humid weather and always follow the pack. Allow ample cure time before flood testing, as Bondall publishes more than one figure for this. Finish toppings must be water-based and solvent-free. Areas with rising damp or negative pressure should first be treated with Betta Damp Stop. Use on concrete slabs with hydrostatic or vapour pressure from below is outside the scope of the independent appraisal. Do not apply when rain is imminent. Always check the technical data sheet for your project.Specifications Brand Bondall (Betta Tilecare) Product Wet Area Waterproofer Pack 10L pail Base Water-based liquid rubber (elastomeric) Application Brush, roller or spray unit Coverage Minimum 1.5L per m2 over two coats (about 6.6 m2 per 10L pail) Dried film thickness Approx. 1.2mm Tack free About 45 minutes Recoat About 1 hour Tile or topping over About 4 to 6 hours (see notes) Standard AS/NZS 4858 Class III membrane Clean up Water Use Residential and commercial wet areas, interior and covered exterior SafetyEven so, wear gloves and eye protection, ensure good ventilation, and avoid contact with skin and eyes. Keep out of reach of children. Store in a sealed container in a cool place and protect from frost. Refer to the Safety Data Sheet (SDS) for full details.
$212.26
![Fastfix Wet Shield One Coat Instant Waterproofing 2.5kg [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/fastfix-wet-shield-one-coat-instant-waterproofing-2-5kg-grey-2.jpg?v=1792410637&width=645)
Fastfix Wet Shield is a fibre-reinforced, one-coat roof and gutter repair membrane that can be applied straight onto wet or damp surfaces, supplied here in a 2.5kg tin in grey. It is made for emergency leak repairs, so you can seal a leaking roof without waiting for the rain to stop, and it also suits planned maintenance work in dry weather.About the formulaA resin-based, solvent-based compound with reinforcing fibres that interlace to bridge small gaps and cracks. The manufacturer describes it as formulated from lightfast acrylic polymers, which helps it withstand UV exposure for longer than traditional bitumen coatings. It is waterproof the moment it goes on, so rain straight after application will not wash it off. It cures to a smooth, seamless, flexible membrane that resists algae and fungal growth. On sound, non-porous surfaces no primer is needed.Where to use itIndoors: not recommended for internal use.Outdoors: roofing and gutter repairs, including tile and metal roofs, valleys, gutters, flashings, fascias, downpipes and cappings, plus concrete and brickwork. Areas that collect ponding water are covered by the one-coat system, provided the recommended minimum finished fall is achieved.Suitable materials include concrete, fibre cement, roof tiles, slate, metal roofing, guttering, brickwork, lead flashing, uPVC, asphalt and bituminous roof coatings. Non-ferrous metals such as aluminium, copper and previously painted non-ferrous metals should be primed with a suitable etch primer first. If you are unsure about a surface, run a small adhesion test before committing to the whole job.How to use itEmergency wet repairs: no preparation is needed. Brush a thick coat over the affected area to create an immediate barrier against water ingress.Planned dry-weather work: clear moss, lichen and debris by brushing, scraping or pressure washing. Let the surface dry, remove any oil or grease with white spirit, and let it dry again. Then apply the product generously with a brush, roller or squeegee in one coat.Seal air-conditioning vents for at least 24 hours during and after application. Clean tools with white spirit or methylated spirits.Important notes Not recommended for wooden surfaces, tanking, fishponds or internal use. Not designed for areas with heavy foot traffic. Allow up to 6 to 7 days to dry, depending on temperature and coat thickness. It may stay soft for longer in some climates, which does not affect its waterproofing. Manufacturer information recommends applying between 5°C and 25°C and a minimum finished fall of 1:80. Discolouration may occur over new asphalt, tar or bitumen. Shelf life is up to 2 years in an unopened container stored correctly. If a primer is needed on a particular substrate, check with the manufacturer for suitable options. Specifications Brand Fastfix Product Wet Shield One Coat Instant Waterproofing Pack 2.5kg tin Colour Grey Base Resin based, fibre reinforced, solvent based Application Brush, roller or squeegee, one coat Coverage 1kg to 2kg per m2, depending on substrate Drying time Up to 6 to 7 days, depending on temperature and thickness Application temperature 5°C to 25°C Minimum finished fall 1:80 Flash point 40°C (per SDS) Clean up White spirit or methylated spirits Use Exterior roofing and gutters SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Avoid breathing vapours, use in a well-ventilated area, and wear protective clothing, eye protection and face protection. For eye contact, rinse with plenty of water for 15 minutes holding the eyelids open. For skin contact, wash with soap and water. Refer to the Safety Data Sheet (SDS) for full details.
$89.91
Crommelin One Coat Rapid is a heavy-duty, liquid-applied waterproofing membrane that goes down before tiling, supplied here in a 1L pail for showers, laundries and other small wet-area jobs. It is a polyurethane-modified grey membrane that cures into a seamless, flexible layer under tile, so there are no laps or joins in the finished surface.About the formulaThe membrane is polyurethane modified for high flexibility and reinforced for strength and durability. Crommelin states it stretches by more than 300% and stays flexible over time, which helps it cope with minor substrate movement. It dries to a keyed, slightly textured surface that gives cement-based tile adhesive something to grip. It is made to be used with cement-based tile adhesives that comply with AS 2358, and it is designed to meet AS 4858 and AS 3740. It is water based, so tools clean up with water.Where to use itIndoors: showers, bathrooms, laundries and kitchens, on both walls and floors, before tiling.Outdoors: balconies, patios and podiums under tile, where the membrane is covered by the tile finish.Suitable substrates include concrete, cement render and screeds, plasterboard and wet-area plasterboard, suitably prepared compressed fibre cement sheet, timber, plywood, wet-area particleboard and steel.How to use itSurfaces need to be sound, clean and dry, with loose or crumbling material removed first. New concrete should have cured for at least 28 days before coating. Where the manufacturer's data sheet calls for a surface primer, use a 1:1 dilution of the membrane with water and let it dry. On walls, one coat is enough, and Crommelin quotes coverage of up to 2m² per litre. Floors need more material per square metre, and complex or irregular surfaces may need extra coats, so check the technical data sheet for your job. Allow good airflow while it cures. Once the membrane has cured, a flood test is described in the manufacturer's data sheet: water about 25mm deep for 2 hours, removed straight afterwards. Clean tools with water before the membrane dries. Uncured material can be removed with warm water and detergent.Important notesThis membrane is not designed to go directly onto white-set plaster. Prime that surface first with a coat of Crommelin Next Day New Concrete Sealer and let it dry. Full cure takes about 7 days. Re-coat and cure times get longer in cold, humid or still conditions. Tile over the membrane so it is not left exposed. Waterproofing wet areas is regulated work in many parts of Australia, so check local requirements and follow the manufacturer's full instructions.Specifications Brand Crommelin Product One Coat Rapid Under-tile Waterproofing Membrane Pack 1L pail Colour Grey Base Polyurethane-modified, liquid applied, water clean up Elongation Over 300% Coverage Up to 2m² per litre (see data sheet for floors and irregular surfaces) Full cure About 7 days Standards Designed to comply with AS 4858 and AS 3740 Use Interior and exterior under-tile applications SafetyUse it with good general ventilation, avoid prolonged skin and eye contact, and wash your hands after use. Store the pail sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$36.48
Crommelin Exterior Grade Brushable Waterproofing Membrane is a tough, flexible synthetic rubber coating for external areas that stay wet, supplied here in a 15L pail for larger jobs. It is designed for permanent water contact, for non-exposed areas with pedestrian traffic, and for use beneath screeds and toppings. It is built to move with the structure rather than crack as the building shifts.About the formulaA ready-to-use, water-based, synthetic rubber membrane (styrene butadiene rubber) in grey. It stays permanently flexible, bridges existing cracks up to 1.5mm and bonds to a wide range of building substrates. It is low VOC and dries quickly. Once cured it can be overcoated with screeds, renders and water-based coatings, so it suits layered waterproofing systems.Where to use itIndoors: not intended as an interior wet-area (under-tile) membrane. Crommelin offers separate products for that job.Outdoors: gutters, roof gardens and terraces, podium decks and balconies, retaining walls, slab edges and fire tanks. It also suits other areas of permanent water contact and non-exposed areas under screeds and toppings.Suitable substrates listed by the manufacturer include concrete and brick, cement render, plywood sheeting, cement sheeting, lightweight aggregate block, trafficable screeds, aluminium and steel (suitably primed).How to use itSurfaces must be sound, clean and completely dry, with no dust, grease, curing compounds, release agents, loose particles or efflorescence. Test moisture content before coating, ideally with an electronic moisture meter. Concrete should be cured for at least 28 days, and screeds and renders for at least 7 days. Remove high points and fill blow-holes and honeycombing with a suitable repair mortar. If the substrate is damp, prime it with Crommelin Dampstop. Treat any rust and remove loose rust material before coating metal. Stir the membrane well, then apply with a Crommelin applicator brush or roller at a surface and air temperature between 10 and 35 degrees Celsius. Recoat once touch dry, which is about 2 hours. Apply the second coat at right angles to the first. Reinforce corners, gutter damage and pin holes with Crommelin reinforcing fabric or bandage. Fit a suitable protection board over the cured membrane before any backfilling.Important notesDo not apply in extreme temperature or humidity. Full cure is about 7 days at 25 degrees Celsius, and coverage varies with substrate porosity. This product is intended for non-exposed pedestrian traffic, so protect the membrane from mechanical damage. Crack bridging applies to existing cracks up to 1.5mm only. Check the current manufacturer data sheet for your specific application and overcoating requirements.Specifications Brand Crommelin Product Exterior Grade Brushable Waterproofing Membrane Pack 15L pail Colour Grey Base Water-based synthetic rubber (styrene butadiene rubber) Application Brush or roller Coverage About 1.5m² per litre, roughly 11m² of finished coating per 15L Recoat time About 2 hours Full cure About 7 days at 25°C Crack bridging Existing cracks to 1.5mm Application temperature 10°C to 35°C Use Exterior, permanent water contact, non-exposed trafficable areas, under screeds and toppings SafetyAvoid contact with skin and eyes, wear suitable gloves and eye protection, and ensure good ventilation when applying. Store in a cool, dry place with the lid sealed. Wash tools in water before the membrane cures. Refer to the Safety Data Sheet (SDS) for full details.
$336.74
Crommelin Blackseal Heavy Duty is a water-based, rubber-modified bitumen waterproofing membrane for below-ground and other non-UV-exposed surfaces, supplied here in a 1L size that suits planter boxes, pots, timber posts and small retaining wall jobs. It is made for surfaces that stay damp or wet and will not be painted, tiled or covered with a finishing coat.About the formulaCrommelin describes Blackseal as a commercial grade bitumen emulsion modified with a synthetic rubber co-polymer. The rubber modification keeps the cured film flexible, so it stays watertight under permanently wet conditions and is suitable for permanent immersion. It helps prevent the damage that moisture transfer causes, including efflorescence, mould growth, staining and paint peeling. It grips a wide range of substrates, is fast drying, and the maker lists it as non-toxic and non-flammable. It can be thinned with up to 50% water to make a bitumen paint.Where to use itIndoors: not intended for interior finishing work or any area that needs a paintable or tileable surface.Outdoors: below-ground and non-exposed exterior surfaces such as garden retaining walls, planter boxes, plant pots, timber posts, water tanks and other non-critical moisture barrier jobs.Suitable materials include concrete, masonry, cement sheeting, timber and metal (check the label for the full substrate list and do a small test area first).How to use itStart with a clean, sound surface free of dust, grease, loose material and anything that could stop the membrane bonding. Stir the product well and apply it evenly with a brush or roller, then allow it to dry before any further coats. Check the label and Crommelin's full instructions for coverage, coat numbers and drying times before you start, and protect the cured membrane from damage if you will be backfilling against it. Clean tools before the product dries (as a water-based product, warm water is the usual method, but confirm on the pack).Important notesNot suitable where it will be exposed to UV or sunlight. It cannot be painted, tiled over, rendered or over-coated, and it is not for trafficable surfaces. If you need a UV-stable option, look at a different Crommelin product. Coverage and cure times depend on the surface and conditions, so treat the listed coverage as a guide and test a small area first.Specifications Brand Crommelin Product Blackseal Heavy Duty Bitumen Waterproofing Membrane Size 1L Colour Black Base Water-based bitumen emulsion, modified with a synthetic rubber co-polymer Application Brush or roller Coverage Approx. 0.75 m² per 1L (retailer listed, guide only) Dilution Up to 50% water to make a bitumen paint Use Below-ground and non-UV-exposed exterior areas Not suitable for UV exposure, painting, tiling, over-coating, trafficable surfaces SafetyThe product itself is not combustible, but once the water has evaporated the organic components can burn or break down in a fire. Avoid contact with eyes and skin, keep out of reach of children, and wash off spills and splashes promptly. Refer to the Safety Data Sheet (SDS) for full details.
$20.75
Crommelin Blackseal Heavy Duty is a black, water-based bitumen waterproofing membrane for below-ground and other non-UV-exposed surfaces, supplied here in a 15L pail for larger jobs. It is a bitumen emulsion modified with a synthetic rubber co-polymer. It dries to a strong, flexible film that stays watertight in permanently wet conditions, which makes it a practical, economical choice where the finished membrane will stay out of sight and out of the sun.About the formulaA water-based bitumen emulsion with a synthetic rubber co-polymer for added flexibility and strength. It grips well to a wide range of building surfaces and is designed to help prevent the damage that moisture transfer causes, including efflorescence, mould growth, staining and paint peeling. The manufacturer describes it as non-toxic, non-flammable, fast drying and suitable for permanent immersion. It can be thinned with up to 50% water if you want a bitumen paint instead of a full-strength membrane.Where to use itIndoors: not intended for interior wet areas such as showers or bathrooms, because it cannot be tiled over or finished with a top coat.Outdoors: below-ground and non-exposed outdoor surfaces, including garden retaining walls, planter boxes, plant pots, timber posts and water tanks. It suits non-critical waterproofing jobs, not areas next to habitable spaces.Suitable surfaces include concrete, concrete blocks, brickwork and other masonry, renders, cementitious substrates, compressed cement and fibre cement sheeting, natural stone, plywood sheeting and timber. It also works on aluminium and steel that have been suitably prepared.How to use itStart with a clean, sound surface free of dust, grease, loose material and flaking coatings. Stir the pail well, then apply with a brush or roller. Two coats are recommended, and the 15L pail covers about 11.25 square metres at that rate. Let each coat dry before applying the next. Mix with water only if you want to thin it for use as a bitumen paint, and do not go past 50% dilution. Wash tools with water straight after use, before the product dries. Check the current Crommelin product information sheet for recoat times and full preparation advice before you start.Important notesDo not paint, tile over or over-coat this membrane, and do not use it on trafficable surfaces. It is not suitable where UV stability is required, so keep it covered or buried. For shower areas or UV-exposed roofs and walls, choose a purpose-made Crommelin membrane instead. Because it is for non-critical applications only, it is not a substitute for a compliant waterproofing system in habitable or wet areas. Cure times vary with temperature, humidity and airflow, so allow enough time before backfilling or exposing the membrane to heavy moisture.Specifications Brand Crommelin Product Blackseal Heavy Duty Bitumen Waterproofing Membrane Pack 15L pail Colour Black Base Water-based bitumen emulsion modified with synthetic rubber co-polymer Application Brush or roller Number of coats 2 Coverage About 11.25 square metres per 15L (two coats) Dilution Up to 50% water to make a bitumen paint Clean up Water, while wet Use Below ground and non-UV-exposed areas only SafetyUse it with good general ventilation. Normal site protection such as safety glasses and overalls is sensible, along with good hygiene. Store the pail sealed, away from extreme temperatures and freezing, and keep it away from strong oxidising agents, strong acids and strong bases. Do not let large spills reach drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$125.78
Crommelin AquaBlock Waterproof Primer Undercoat is a water-based primer, sealer and stain-blocking undercoat made for damp-prone areas of the home, supplied here in a 1L tin that suits bathroom, laundry and small repaint jobs. It builds a water-resistant, paintable base over bare and previously painted surfaces, so water-based topcoats can go on over an even, sealed surface.About the formulaAquaBlock is a high-cover, low-odour wall primer with a flat finish. Crommelin positions it as a sealer, primer, undercoat and stain blocker in one product. It grips both porous and non-porous surfaces, seals off stains and gives topcoats a uniform surface to bond to. The manufacturer also describes it as a mould-resistant undercoat, which makes it a sensible choice for bathrooms, kitchens and laundries. It is designed to be overcoated with water-based paints and cleans up with water.Where to use itIndoors: walls and ceilings in bathrooms, kitchens, laundries and hallways, especially where steam, condensation or past moisture damage has caused staining or peeling.Outdoors: eaves and exterior walls and other masonry or timber surfaces that will be topcoated with a water-based paint.Suitable surfaces include plasterboard, brick, concrete and concrete blocks, cement sheeting, render, masonry, timber, plywood, particleboard and suitably prepared steel.How to use itMake sure the surface is clean, dry, sound and free of dust, grease, loose paint and mould before you start. Stir the product well, then apply it with a brush or roller. Check the label for the recommended number of coats and the spread rate for your surface. Apply only when the temperature is at least 5°C. The retailer lists a recoat time of about 120 minutes. Clean brushes, rollers and tools with water straight after use, before the product dries.Important notesThis product is not tintable and is supplied in white only. Crommelin advises it is not suitable over white set plaster and should not be used as a base before tiling. It is a primer and undercoat, not a decorative finish, so topcoat it with a water-based paint. Surface and weather conditions affect drying and performance, so test a small area first on unusual or heavily stained substrates. Check the label for full application details.Specifications Brand Crommelin Product AquaBlock Waterproof Primer Undercoat Size 1L tin Colour White (not tintable) Finish Flat Base Water-based Application Brush or roller Coverage 12 to 14 m² per litre (retailer figure; check the label) Recoat time About 120 minutes Minimum application temperature 5°C Clean up Water Topcoat Water-based paints Use Interior and exterior SafetyEven so, avoid contact with skin and eyes, wear suitable protective clothing and gloves, and use it in a well-ventilated area. Keep the lid on the tin when not in use, store it in a cool, dry place and protect it from freezing. Keep it out of reach of children. Do not tip leftover product or wash water into drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$37.54
Crommelin Shower Waterproofing Membrane is a ready-to-use, water-based liquid membrane for waterproofing wet areas before tiling, supplied here in a 15L pail for larger bathroom, laundry and balcony jobs. It cures to a continuous, flexible rubber-like layer with a textured surface, so cement-based tile adhesive can bond directly over the top.About the formulaA heavy duty, modified rubber (styrene butadiene rubber) liquid membrane that is applied seamlessly, with no joins or laps, for leak-free performance. It stays permanently flexible with high elongation, so it can cope with normal movement in the substrate. It dries to a keyed finish suited to all cement-based tile adhesives that conform to AS 2358, and it complies with AS 3740 (Waterproofing of wet areas). It is a water-based product, so tools clean up with water.Where to use itIndoors: under tiles in showers, bathrooms, laundries, kitchens and wet rooms, on both walls and floors.Outdoors: under-tile waterproofing on balconies. The membrane can be applied either below or above a screed.Suitable substrates include concrete and masonry, cement renders and screeds, plasterboard and wet area gyprock, compressed fibre cement sheeting, timber, plywood sheeting and wet area particleboard, and suitably prepared steel.How to use itPrepare the surface first. Remove high points and protrusions, fill any blow-holes or honeycombing with a suitable repair mortar, and bring the surface back to an even profile. New concrete should have cured for at least 28 days and screeds or renders for at least 7 days. The surface must be clean, sound and completely dry. Free it from dust, grease, curing compounds, release agents and loose particles. Check moisture with a meter. If the substrate is not dry enough, prime it with Crommelin Dampstop.The membrane is ready to use, so stir it well and apply with a brush or roller. Apply at least two coats and allow the first to dry before recoating. Complex or very irregular surfaces may need extra coats. Apply only when surface and air temperatures are between 10 and 35 degrees C and humidity is below 85%.Tile over after the membrane has dried and cured for the recommended time. A flood test can be done after 48 hours by ponding water to a depth of 25mm for 2 hours, then removing the water straight away. Wash tools with water before the product dries. Uncured material can be removed with warm water and detergent.Important notesNot suitable for use over white-set plaster. Do not apply over damp substrates, and do not apply in extreme heat, cold or humidity. Allow good airflow so the membrane can cure properly. Full cure takes about 7 days. Recoat and tile-over times vary with temperature and humidity, so check the current Crommelin data sheet for your conditions. Crommelin lists companion products for detailing, including reinforcing fabric with bond breaker, Dampstop primer, polyurethane sealant and Silicone WP Plus. Always apply a trial patch if you are unsure about a substrate.Specifications Brand Crommelin Product Shower Waterproofing Membrane Pack 15L pail Colour Green Base Water-based, modified rubber (SBR) liquid applied membrane Application Brush or roller, ready to use after stirring Coverage About 2m2 per litre per coat, minimum 2 coats (about 15m2 of finished membrane from 15L) Application temperature 10 to 35 degrees C, maximum humidity 85% Tile over After a minimum of 48 hours Full cure 7 days Standards Complies with AS 3740; suitable for use with cement-based tile adhesives conforming to AS 2358 Use Under-tile wet area waterproofing SafetyEven so, ensure good ventilation, avoid breathing vapours or spray, avoid skin and eye contact, and wear gloves and eye protection. Remove splashes from skin promptly. Keep the container sealed when not in use, store it cool and dry, and protect it from freezing and extreme temperatures. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$273.47
Crommelin Shower Waterproofing Membrane is a ready-to-use, liquid-applied under-tile membrane for waterproofing showers and other wet areas before tiling, supplied here as a 1L pail for small jobs and repairs. It cures to a seamless, flexible waterproof layer with a textured surface that tile adhesive can grip, so you can tile straight over it.About the formulaA water-based, heavy-duty, modified rubber membrane that is applied wet and dries into a continuous film with no joins to leak. The manufacturer describes it as permanently flexible with high elongation, with excellent adhesion to the substrate and a keyed finish that promotes direct tile adhesion. It complies with AS 3740 (Waterproofing of domestic wet areas) and is suitable for use with cement-based tile adhesives that conform to AS 2358. It can be applied either below or above a screed.Where to use itIndoors: showers, bathrooms, laundries, kitchens and wet rooms, on both walls and floors, under tiles.Outdoors: balconies, under tile.Suitable substrates include concrete and masonry, cement renders and screeds, plasterboard and wet area plasterboard, compressed fibre cement sheet (suitably prepared), timber, plywood sheeting, wet area particleboard and steel. It is not suitable for use over white-set plaster.How to use it Prepare the surface so it is clean, dry, sound and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and laitance. Concrete should have cured for at least 28 days, and screeds and renders for 7 days. Fill any holes or honeycombing with a suitable repair mortar and remove high points so the surface is even, with a light texture. If the substrate is not dry, prime it with Crommelin Dampstop. If the surface needs more consolidation, apply one coat of Crommelin Powerflex first. The product is ready to use. Stir it well, then apply with a 75mm or 100mm membrane brush or a 230mm membrane roller cover. Apply only when surface and air temperatures are between 10°C and 35°C. The manufacturer's recoat time is about 2 hours and the tile-over time is about 48 hours. Follow the Crommelin technical data sheet for detailing at corners, joints and penetrations. Important notesOne litre produces about 1m² of finished membrane, which means building up the full film in the coats the technical data sheet specifies. Do not apply in conditions that are too hot or too cold. Make sure the substrate is properly cured and prepared before you start, because the membrane is only as good as the surface under it. For anything beyond a small area or minor repair, the 4L size may suit better. Check the current Crommelin data sheet for the full system and for the requirements that apply to your job.Specifications Brand Crommelin Product Shower Waterproofing Membrane Pack 1L pail Colour Green Base Water-based, modified rubber, liquid applied Application Brush or roller Coverage About 1m² of finished membrane per litre Recoat time About 2 hours Tile over About 48 hours Application temperature 10°C to 35°C Standards Complies with AS 3740; compatible with cement-based tile adhesives to AS 2358 Use Interior and exterior, under tile SafetyUse it with good general ventilation, avoid contact with skin and eyes, and wear suitable protective clothing. Do not let large spills reach drains or waterways. Store the pail in a cool, dry place out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$34.14
Crommelin Shower Waterproofing Membrane is a ready-to-use, water-based liquid membrane that waterproofs showers, bathrooms and other wet areas before tiling, supplied here in a 4L pail. It rolls or brushes on as a seamless, flexible layer and dries to a textured finish that tile adhesive can grip, so you can tile directly over it.About the formulaA heavy duty, modified rubber membrane in a water-based, ready-to-use form with no mixing. Once cured it stays permanently flexible and stretches well, so it can cope with small movements in the substrate. It sticks well to suitable surfaces. The keyed surface works with cement-based tile adhesives, and Crommelin states it suits all cement-based adhesives that meet AS 2358. It complies with AS 3740 (waterproofing of wet areas). The 4L pail makes about 4 square metres of finished membrane, which is enough for a standard single shower recess.Where to use itIndoors: under-tile waterproofing of shower recesses and bathrooms, on both walls and floors, and in other internal wet areas such as laundries.Outdoors: not specified by the manufacturer for this product. Check the Crommelin technical data sheet or contact Crommelin before using it on exposed external areas.Suitable surfaces listed by the manufacturer include concrete and masonry. Check the current technical data sheet for the full list of approved substrates, and confirm that wet area fibre cement, plasterboard or similar sheeting is approved before you start.How to use it Make sure the substrate is clean, sound and completely dry before you apply anything. Apply with a brush or a suitable membrane roller. Crommelin lists its Contractor Membrane Roller Cover as a compatible tool. At least 2 coats are required. Apply the second coat at 90 degrees to the first. Allow about 2 hours drying time between coats, as per the Crommelin how-to guide. Coverage is about 2 square metres per litre per coat. Complex or very irregular surfaces may need extra coats. Crommelin lists Dampstop, Reinforcing Fabric (with or without bond breaker), Polyurethane Sealant and Silicone WP Plus as compatible products for details and junctions. For a flood test, wait 48 hours, then pond water to a depth of 25mm for 2 hours. Remove the test water straight away afterwards. You can tile over the membrane after 48 hours. Clean tools and equipment with water before the membrane dries. Important notesFull cure takes 7 days. Do not apply to a damp substrate. Wet area waterproofing should be done to the requirements of AS 3740 and your local regulations, and many jurisdictions require a licensed waterproofer for the work. If in doubt, check before you start. This product is water-based, so keep the pail sealed and protect it from frost and extreme heat during storage.Specifications Brand Crommelin Product Shower Waterproofing Membrane Size 4L pail Colour Green Base Water-based, modified rubber Application Brush or roller, 2 coats minimum Coverage About 2 m² per litre per coat (about 4 m² finished membrane from 4L) Recoat About 2 hours Tile over / flood test After 48 hours Full cure 7 days Standards Complies with AS 3740; suitable with cement-based tile adhesives to AS 2358 Use Under-tile waterproofing of showers, bathrooms and wet areas, walls and floors Clean up Water, before drying SafetyAvoid contact with eyes and skin, and wear gloves and eye protection when applying it. Make sure the area is well ventilated while you work and while it dries. Keep out of reach of children. If it gets in your eyes, rinse with plenty of water. Refer to the Safety Data Sheet (SDS) for full details.
$93.15
Gripset Betta Bitumen Rubber is a two-in-one, solvent-free liquid membrane in a 1 litre pail, supplied here for waterproofing underground, immersed and general building work. Apply it as a bitumen polymer membrane, or dilute it with water to make an economical black bitumen paint where a full membrane is not needed.About the formulaA water-based, concentrated bitumen and latex polymer liquid that dries to a flexible black film. The manufacturer describes it as solvent free, with good sealing and adhesion on a range of building surfaces. It can be applied to damp surfaces provided there is no standing water, and it is approved for potable water contact (tested at an exposure of 1000mm2 per litre). Diluted 1:1 with water, 1L of concentrate makes 2L of bitumen paint.Where to use itIndoors: interior areas that need a waterproof or protective coating, where a membrane or bitumen paint suits the job.Outdoors: underground and retaining walls, garden beds, planter boxes and landscaped areas, fish ponds, stock troughs and water features, and general protective coating work. It also suits fully immersed applications when applied at the higher immersed coverage rate.Suitable surfaces include concrete, masonry, brick, timber, cement sheeting, metals and aged bitumen, along with other common building surfaces. If you plan to coat over existing paints or finishes, check with Gripset Betta first.How to use itStart with a clean, sound surface free of loose material and standing water. The product is self-priming. For porous surfaces, the manufacturer's literature suggests diluting the first coat with water (about 1 part concentrate to 3 parts water). Use a separate primer on non-porous or smooth surfaces and on surfaces affected by rising damp. Apply by brush, roller, trowel or spray, working each extra coat in a different direction to the one before.As a membrane, apply at least 2 coats at a combined minimum of 1.5 litres per square metre, which gives a dried film of about 1.2mm. For immersed areas, allow a minimum of 2 litres per square metre. Uneven or porous surfaces can need more. For paint use, mix the concentrate with clean water 1:1 by volume. Wash tools in water while the product is still wet.Important notesDrying times at about 20°C: tack free in 60 to 90 minutes, recoat after 2 to 4 hours, dry film in 24 hours, backfilling underground after 4 days, and immersed areas after 21 days. Temperature, humidity and surface porosity all change these times. Once dry, the product has to be removed mechanically or with solvent. For potable water use, wash the surface down and discard the first fill before using the water for drinking. At the minimum membrane rate, 1L covers well under 1 square metre, so check quantities before you buy.Specifications Brand Gripset Betta Product Bitumen Rubber Waterproofing Membrane Pack 1 litre pail Colour Black Base Water-based bitumen and latex polymer, solvent free Application Brush, roller, trowel or spray Membrane coverage Minimum 1.5 L/m2 in 2 coats (2 L/m2 for immersed areas) Paint dilution 1 part concentrate to 1 part water Tack free 60 to 90 minutes Recoat 2 to 4 hours Dry film 24 hours Immersed areas 21 days Clean up Water, while wet Use Interior, exterior, underground and immersed SafetyIt is non-flammable as supplied, but the dried film will burn in a general fire. Wash your hands after use and before eating, drinking or smoking. Do not let it enter drains, sewers or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$27.04
Dunlop Rapid Bond Coat is a water-based bonding coat that creates a chemical key on smooth, dense, non-porous surfaces, the ones ordinary primers struggle to grip. Applied before Dunlop adhesives, floor levelling compounds or Dunlop undertile waterproofing membranes (in non-immersed situations), it transforms slick substrates such as glazed tiles into a surface your next product can actually hold onto. It is the product that makes tile-over-tile renovations possible without demolition, and its rapid-drying formula keeps the job moving.Where to use itSuitable for indoor and outdoor use on walls and floors. Use it over glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement and compressed fibre-cement sheet, Scyon and internal sheet timber.How to useClean the surface thoroughly, degreasing glazed or dense substrates so nothing interferes with the bond. Apply a thin, even coat by brush or roller and allow it to dry before applying your adhesive, leveller or membrane. Being water-based, wet product cleans off tools with water.Important notesRapid Bond Coat is designed for smooth, dense and difficult non-porous substrates; for ordinary porous surfaces use Dunlop Multipurpose Primer instead. When used under waterproofing it is for non-fully-immersed applications only. Coverage varies with the substrate and application method.Specifications Size 1 litre Coverage Approx. 10m² per litre Substrates Glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement, Scyon, internal sheet timber Drying Rapid drying SafetyVentilate the room, wear gloves, and avoid contact with eyes and skin. Store the sealed bottle away from children and check the Safety Data Sheet before use.
$67.73
Dunlop Multipurpose Primer in the 4 litre pack is the job-sized version of Dunlop's water-based bonding primer, made for whole-room and whole-house preparation work. It improves the bond between the substrate and Dunlop floor levellers, renders, tile adhesives and waterproofing membranes, turning dusty, porous surfaces into a reliable base. It suits new and old concrete, particleboard and compressed fibre-cement sheets alike.Where to use itUse indoors or outdoors, on walls and floors. It is at home on fibre-cement sheeting, concrete slabs, masonry and lightweight concrete blocks, particleboard, renders and screeds, before levelling, rendering, tiling or waterproofing with Dunlop systems.How to usePrepare the surface so it is clean, dry and free of dust, grease and loose material. Pour out the primer and spread an even coat with a brush or roller, working it into the surface. Let it dry clear before applying the next product in your system. Wash tools in water immediately after use.Important notesOn very porous substrates a second coat is required to achieve a continuous primed film. The white-on, clear-dry formula shows exactly where you have coated. Actual coverage depends on substrate porosity and site conditions.Specifications Size 4 litres Coverage Approx. 6m² per litre (up to approx. 24m² per pack) Substrates Fibre-cement, concrete, masonry, lightweight blocks, particleboard, renders, screeds Colour Applies white, dries clear SafetyWear gloves and eye protection, keep the work area ventilated, and avoid prolonged skin contact. Keep away from children and refer to the Safety Data Sheet before starting.
$60.26
Dunlop Multipurpose Primer is a water-based primer engineered to strengthen the bond between a substrate and the Dunlop product applied over it. It is the go-to preparation step for flooring work, priming ahead of floor levellers, renders, tile adhesives and waterproofing membranes, and it performs equally well on new or old concrete, particleboard and compressed fibre-cement sheeting.Where to use itApproved for indoor and outdoor use on both walls and floors. Typical substrates include fibre-cement sheets, concrete, masonry and lightweight concrete blocks, particleboard, renders and screeds. Prime before levelling a slab, rendering a wall, waterproofing a bathroom or laying tiles.How to useSweep or vacuum the surface so it is clean, sound and free of dust, oil and curing compounds. Apply an even coat by brush or roller and allow it to dry clear before applying your leveller, render, adhesive or membrane. Because it is water-based, brushes and rollers wash out in water straight after use.Important notesVery porous substrates will drink in the first coat, so a second coat is required to build a proper film. The primer applies white and dries clear, making coverage easy to track. Coverage figures are a guide only and vary with surface condition.Specifications Size 1 litre Coverage Approx. 6m² per litre Substrates Fibre-cement, concrete, masonry, lightweight blocks, particleboard, renders, screeds Colour Applies white, dries clear SafetyKeep off skin and out of eyes, wear gloves, and ensure good ventilation while working. Store sealed and away from children. Consult the Safety Data Sheet for full handling guidance.
$34.59
Stop leaks fast with Gorilla Patch and Seal Tape. This ultra thick, flexible sealing tape conforms to rough, uneven, and curved surfaces to create a strong, watertight barrier. Ideal for emergency fixes and long term maintenance around the home, workshop, caravan, and boat. Why you will love it Instant waterproof seal helps stop leaks on contact Works above or below the waterline for pools, gutters, and marine jobs UV and weather resistant for outdoor use Conforms and stretches to seal gaps, cracks, and seams Sticks to many surfaces including PVC, metal, plastic, glass, tile, and more Great for Repairing pinholes and cracks in gutters and downpipes Patching above ground pool liners and inflatable pools Sealing roof sheets, skylights, flashings, and RV seams Fixing garden hoses, buckets, and water features Temporary window and greenhouse repairs Surface compatibility Material Suitable Notes PVC, ABS, most rigid plastics Yes Clean and dry for best bond Metal, aluminium, galvanized steel Yes Remove rust and loose paint Glass, glazed tile, ceramics Yes Degrease surface Rubber, EPDM, vinyl Yes Press firmly to conform Textured masonry, concrete Yes Fill deep voids first for a flat seal Silicone coated or oily surfaces No Adhesion is limited How to use Prep Clean and dry the area. For underwater patches, wipe away algae or loose debris. Measure Cut a piece that extends past the damage by at least 25 mm on all sides. Apply Peel the liner and place tape over the damage. Start from the centre and work outwards. Seal Press down hard, removing air bubbles. Use a roller or rounded tool for maximum contact. Cure Initial grab is immediate. Full bond strength improves over 24 hours. Tips for best results Round the corners of the patch to reduce lifting For high pressure leaks, apply a larger patch or multiple layers Do not apply over active flowing water without reducing the flow first Frequently asked Can I use it underwater Yes. It can be applied to wet surfaces and submerged areas. Clean the surface as well as possible for the best seal. Is it paintable Most tapes are not paintable. If appearance matters, trim neatly and paint the surrounding surface instead. Is it a permanent fix It provides a durable seal for many applications. For structural or critical repairs, consider a permanent fix when practical. Good to know Temperature use range typically suits most Australian conditions Store in a cool, dry place and keep the roll protected from dust Glues Australia keeps Australia together. If you need help choosing the right sealing solution for your job, contact our team.
$57.40 $40.04
Dulux Precision Maximum Strength Adhesion Primer Get a tough, reliable bond on hard to paint surfaces with Dulux Precision Maximum Strength Adhesion Primer. This water based, low odour primer works as a primer, sealer and undercoat, creating a strong foundation for acrylic or oil based topcoats on both interior and exterior projects. Why choose this primer Water based with low odour Excellent adhesion on glossy and hard to coat surfaces Suitable as primer, sealer and undercoat Interior and exterior use Fast drying: touch dry in 30 minutes, recoat in 1 to 2 hours Topcoat within 30 days for best results Ideal surfaces Tiles, high gloss enamels, varnished timber, uPVC, fiberglass, aluminium, galvanised steel, Colorbond, glass, glazed brick, laminates and previously painted glossy finishes. Key specs Finish Flat Colour White Coverage Up to 10 m² per litre per coat, depending on surface Dry time Touch dry 30 minutes Recoat time 1 to 2 hours Full strength 7 days after application VOC 30.4 g/L Application temperature Between 10°C and 32°C Clean up Water Pack sizes 1 L and 4 L How to use Prepare the surface so it is clean, dry and free of grease, wax, dust, loose paint and rust. Wash if needed and allow to dry. Stir thoroughly before and during use. Apply 1 even coat with a high quality brush, roller or spray. For very smooth surfaces 1 coat is usually sufficient. Allow 1 to 2 hours before recoating or applying the topcoat. Topcoat within 30 days. Application tips Do not tint for difficult surfaces. Thin only if necessary with a small amount of water. When using solvent based enamel topcoats, lightly sand the primer before applying the enamel. If using under products with strong solvents, let the primer dry 24 hours and test compatibility on a small area first. Where not to use Floors, benchtops or surfaces subject to standing water Below 10°C surface temperature or if conditions may drop below 10°C during drying Clean up and safety Clean tools with water and a mild detergent, then rinse. Ensure good ventilation during use. Wear eye protection and avoid skin and eye contact. Always follow label directions.
$260.30
Dunlop Pressure Sensitive Carpet Tile Adhesive 2L Dunlop Carpet Tile Adhesive is a high strength, water based pressure sensitive adhesive designed for carpet tiles and double bonded underlay systems. It tacks off to a clear, dry-to-touch film that grips firmly yet allows tiles to be lifted and replaced for maintenance. Key features Pressure sensitive grab for secure hold and easy tile replacement Water based, low odour, easy to apply Suitable for smooth or textured tile backings and composition vinyl tiles Works with double bonded underlays in commercial fitouts Suitable substrates Concrete, plywood, fibre cement sheet, compressed fibre cement, and suitable underlay sheets. Subfloors must be dry, smooth, clean, and prepared to AS 1884 requirements including moisture testing. Coverage Approx. 10 m² per 2 L using a 1.6 mm V notched trowel Approx. 14 m² per 2 L using a long nap roller Drying and traffic Allow adhesive to become tacky and transparent before laying tiles. Typical tack off time is 2 to 4 hours depending on conditions. Heavy foot traffic after 24 hours Avoid wet cleaning or water exposure for 48 hours Application guide Prepare the subfloor. Prime very porous substrates if required. Treat rising damp or green concrete with a suitable moisture barrier. Apply adhesive evenly: Textured backs, composition vinyl tiles, and double bond underlays: 1.6 mm V notched trowel held at about 60 degrees Smooth backed tiles: long nap roller Wait until the film is tacky and clear with no transfer to fingertips. Early placement into wet adhesive will create a more permanent bond. Lay tiles, cut and reposition as required, then roll in both directions with a suitable roller to ensure full contact. Clean up Clean tools immediately with warm soapy water. Remove dried residue with mineral turps. Storage and shelf life 12 months in unopened packaging when stored in a cool, dry place at about 23°C and 50% RH. Good to know Do not apply below 15°C or above 30°C surface temperature. Not suitable for traditional carpet-to-underlay stretch-in installations. For double bond systems, follow the flooring manufacturer’s instructions. Safety Wear gloves and eye protection, ensure adequate ventilation, and keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$38.56
Bostik Glu Tape is a clean, quick and mess free double sided adhesive for everyday sticking and craft projects. At 6 mm wide and 12 m long, it gives precise control for cards, scrapbooks, posters, school projects and office tasks. Why you will love it Instant stick with no drying time Clean finish with no liquid glue spills Thin 6 mm width for neat, accurate placement Strong hold on most paper and lightweight materials Great for home, school and office use Great for Card making and scrapbooking Mounting photos, prints and posters Sealing envelopes and gift wrapping School assignments and craft projects Suitable surfaces Paper and cardboard Lightweight foam and foamboard Most coated papers and photo papers How to use Ensure surfaces are clean, dry and free of dust or oils. Apply the tape along the area to be bonded, pressing down firmly. Peel away the release liner if present, then align and press surfaces together. Rub over the bond area to secure a strong hold. Tips Test on delicate or coated papers before full application. For best results, apply at room temperature and avoid stretching the tape. Store in a cool, dry place out of direct sunlight. Specifications Type: Double sided adhesive tape Width: 6 mm Length: 12 m Color: Clear adhesive Pack contents: 1 roll
$10.60
Earl’s Graffiti Barrier & Remover System – Non-Toxic, Biodegradable Stop graffiti before it sticks—and remove it fast when it does. This two-part system pairs a sacrificial Graffiti Barrier coating with a powerful, non-caustic Graffiti Remover. Use the Barrier to shield vulnerable surfaces so future tags release easily, and use the Remover to dissolve existing graffiti on common building substrates. Both products are non toxic, contain no caustic soda, and are designed for safe, simple use in domestic or commercial settings. Why choose this system Complete solution: Protect plus remove—works as a proactive coating and a reactive cleaner. Non-toxic & biodegradable: No caustic soda; safer handling and cleanup. Wide surface compatibility: Brick, cement render, timber fences, stone, metal, garage doors, and signage (always test first). Fast turnaround: Barrier rolls or brushes on quickly; Remover dissolves graffiti that can be rinsed away with water. Made for Australian conditions: Practical directions for real-world sites—homes, schools, retail, body corporate assets, and councils. What’s in the box Earl’s Graffiti Barrier: A sacrificial, protective coating that forms an invisible* shield to make future clean-downs faster and gentler. Earl’s Graffiti Remover: A non-caustic cleaner that dissolves graffiti so residues can be scrubbed and rinsed away. *Appearance may vary by substrate; see Specifications and always test a small area first. Where to use Masonry: Bricks, blockwork, stone, concrete/cement render. Timber & metal: Timber fences, metal doors, garage doors, and metal signage. High-risk zones: Laneways, rear service doors, fence lines, public-facing walls, and transport corridors. How it works The Barrier creates a sacrificial layer. When tagging occurs later, graffiti sits at or near the surface and releases more readily during cleanup. The Remover penetrates and dissolves paints/inks so they can be agitated and rinsed from the substrate, especially effective on porous mineral surfaces and surfaces previously treated with the Barrier. Directions 1) Apply the Graffiti Barrier (preventive) Prep: Surface must be clean, dry, sound, and free of dust, oil, or old failing coatings. Mask adjacent areas. Application: Stir/shake well. Apply sparingly by roller or brush in a single, consistent roll direction. Coverage: Up to ~6 m²/L on render or dark/porous surfaces (coverage varies by substrate profile and porosity). Conditions: Do not apply below 12 °C or in very cold/damp conditions. Appearance: Dries to an opaque protective film; test a small inconspicuous area to confirm finish/visual impact. 2) Use the Graffiti Remover (reactive) For unpainted mineral surfaces: Spray or liberally apply Remover directly to the graffiti. Allow time for the film to soften/dissolve. Agitate: Scrub with a stiff bristle brush to lift residues from pores and profiles. Rinse: Wash off thoroughly with clean water. Repeat on deeply embedded areas if required. Barrier not previously applied? The Remover can still be used to clean most common surfaces; repeat as necessary. Pro tips Always conduct a spot test in an inconspicuous area to verify appearance and cleaning performance. Highly porous or dark substrates may need additional coats of the Barrier for consistent protection. Schedule maintenance inspections in high-risk locations so tags are removed promptly, discouraging re-offending. Clean-up & safety Use appropriate PPE (gloves/eye protection). Provide ventilation when working in enclosed areas. Avoid runoff into drains and waterways. Collect residues where practical and dispose of in accordance with local regulations. Store sealed in a cool, dry place away from direct sun and sources of ignition. Keep out of reach of children. Specifications Property Graffiti Barrier Graffiti Remover Function Sacrificial protective coating to ease future graffiti removal Non-caustic graffiti dissolver for reactive cleaning Key claims Non toxic, non caustic, biodegradable Non caustic; designed to dissolve graffiti for water rinsing Suitable substrates Brick, cement render, stone, timber fences, metal, garage doors Brick, cement render, stone, timber fences, metal, garage doors, metal signs Appearance / finish Dries opaque (test first for visual impact) Clear liquid cleaner (appearance varies by manufacturer’s batch) Application method Roller or brush (single roll direction) Spray/apply, dwell, scrub, rinse with water Coverage (guide) Approx. 6 m²/L on render or dark/porous surfaces (substrate dependent) Consumption varies with thickness of graffiti and porosity Application temperature Do not apply below 12 °C Use in ambient conditions; avoid extreme heat/cold; ventilate area Cleanup Allow to dry; future clean-downs remove tags more easily Rinse dissolved residues thoroughly with clean water Typical uses Preventive protection for high-risk surfaces Removal of existing tags and markers
$37.95
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$24.43
LOCTITE 518 is a medium-strength, general purpose gasketing product with excellent contamination tolerance. Ideal for use on casted iron, steel and aluminum flanges. LOCTITE® 518 cures when confined in the absence of air between close-fitting metal surfaces. It is an anaerobic gasketing material designed for use on rigid iron, aluminum, and steel flanged mating surfaces. LOCTITE 518 fills gaps up to 0.25mm and forms a flexible, chemical-resistant seal that will not tear or decay. Parts disassemble easily, even after extended service. Typical applications include sealing close-fitting joints between rigid metal faces and flanges. It is also used as a formed-in-place gasket on rigid flanged connections, e.g. transmissions and motor housings. Semi-flexible, medium-strength anaerobic flange gasket Easy to automate Reduces process costs – eliminates manual assembly of conventional gaskets NSF P1 Reg. No. 123758 For active and inactive rigid metal flanges Cures through minor surface contamination Adapts to flange surface irregularities and gaps up to 0.25 mm Gel-type consistency Seals instantly against low pressure Reduces inventory costs – no need for large inventory of cut gaskets Resists high pressure when fully cured No compression set or misaligned gaskets Technical Information Applications Rigid Assembly Gasketing Colour Red Cure Schedule Temperature (Step 1) 200 Cure Schedule Temperature Unit (Step 1) °C Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.3 mm Shelf Life Temperature -40 °C Specific Gravity 1.1 g/l Specific Gravity Temperature 25 °C Substrates Metal: Aluminum Temperature -65 - 300 °F Tensile Shear Strength 7.5 N/mm² Viscosity 500000 - 1000000 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$9.95
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
$40.93
Dunlop Express Wet Area Waterproofing Membrane is a high-performance, fast-drying liquid membrane designed for use in internal wet areas including bathrooms, showers, laundries, and kitchens. This flexible, water-based acrylic polyurethane formulation creates a seamless and highly durable waterproof barrier that is tile-ready within hours. It’s suitable for use under tile adhesives, screeds, and other flooring products. The product forms a tough, elastomeric layer that resists movement, cracking, and water penetration. It meets the requirements of Class III membranes and is suitable for both floor and wall applications. Surface Preparation: Ensure all surfaces are clean, dry, and structurally sound. Remove dust, grease, oil, curing compounds, and loose or flaking materials. Prime all surfaces using a compatible primer. On porous or highly absorbent surfaces, apply a second primer coat if needed. Any existing cracks, gaps, or joints should be sealed or reinforced using bond breakers or reinforcing fabric. Application Instructions: Apply the membrane using a brush or roller. Two coats are required for effective waterproofing. First coat should be applied in one direction. Once dry to the touch (approx. 2 hours), apply the second coat in the opposite direction. Membrane should extend at least 150mm up walls in general wet areas and 1.8m in shower recesses. Waterproofing must be applied continuously and without breaks or pinholes. Use reinforcing fabric over joints and corners if required. Avoid application in conditions below 10°C or above 35°C. Coverage: Approximately 1m² per litre per coat. A 5kg pail covers roughly 2.5m² with two coats, depending on surface porosity. Drying Time: Touch dry: 1–2 hours Recoat time: 2 hours Ready for tiling: 4–6 hours Fully cured: 24 hours Drying times will vary with ambient temperature and humidity. Clean Up: Clean tools and equipment immediately after use with water. Do not allow membrane to dry on tools. Technical Data: Type: Water-based acrylic polyurethane Classification: Class III membrane Application Method: Brush or roller Flexibility: High Water Resistance: Excellent Colour: Grey Shelf Life: 12 months (unopened in cool, dry conditions)
$80.40
You have seen 48 out of 53 products
Roller-grade adhesives for broad, uniform coverage on floors, laminates and panels. Choose the recommended roller nap to achieve the specified spread rate and film thickness; avoid puddling and missed spots. Use filters to refine by chemistry, open time and temperature rating. Always follow the product page and TDS/SDS for prep, application and curing.
