Note: This product is formulated for timber floors. If you need an adhesive for tiled floors, please use the regular Fix-A-Floor available Click here. NEW – Fix-A-Floor Polyurethane Wood Floor Repair Adhesive features an extra-strength, super-blend formula specifically designed for re-bonding loose, hollow, squeaky, popping, or bouncy timber floors. There’s no need to remove or replace floorboards — simply Drill & Fill for a long-lasting, nearly invisible repair. The precision nozzle allows for very small drill holes, ensuring a clean finish. Ideal for all solid hardwood, engineered timber, and bamboo floors. Suitable for both indoor and outdoor use, and for small or large repair areas. Odourless and very low in VOCs. Coverage: One 300 mL tube covers approximately 0.37 m² (around 600 mm x 600 mm). Just Drill & Fill! Flooring professionals often prefer polyurethane when repairing timber floors due to its strength and flexibility. The Fix-A-Floor polyurethane formula does not foam or expand when applied and cures within 24 hours. Once set, it moves naturally with the timber’s expansion and contraction, preventing cracking or bond failure. Perfect for permanently fixing loose, squeaky, or bouncy floors. Not recommended for use in moist or wet areas. The Fix-A-Floor Large Application Syringe is another excellent option for applying the adhesive if you’d like to drill even smaller holes than 3.5 mm. Always test on a small area first to confirm desired results, and keep from freezing before use. Directions for Repairing Timber Floors: Locate problem areas by tapping the floor with a wooden dowel, broom handle, or similar object, and mark the perimeter using chalk or painter’s tape. Inside the marked area, use a 3.5 mm drill bit and drill at least one hole on each end of the affected floorboard(s). Larger areas may require additional holes. Vacuum debris from each hole. Remove the cap and unscrew the nozzle. Pierce a large hole in the tube with an awl or similar tool. If needed, clear the nozzle before screwing it back on. Using a quality caulking gun, inject Fix-A-Floor into each drilled hole. When adhesive seeps from adjacent holes, you have achieved full coverage. Place a finger over the nozzle when moving between holes to prevent spills. Once complete, wipe away any excess with a damp cloth or sponge and allow to cure for 24 hours before filling holes. Use a matching timber filler or putty from your local hardware store. Clean any residue with mineral turpentine. Your floor is FIXED!
$54.95 $49.95
Sikaflex®-291 Black Marine-Grade Polyurethane Sealant 150mL is a premium, one-component, non-sag adhesive sealant specially formulated for marine environments. It cures on exposure to atmospheric moisture, forming a strong, elastic, and durable bond that resists saltwater, vibration, and weathering. Trusted by boat builders and marine professionals worldwide, Sikaflex®-291 meets International Maritime Organisation (IMO) standards for safety and performance. Features & Benefits Marine-grade polyurethane formula with superior adhesion Excellent weathering and saltwater resistance Elastic and vibration-resistant for long-lasting seals Low odour and non-corrosive composition Can be sanded and overpainted after curing Maintains flexibility across wide temperature ranges Where to Use Sealing and bonding on boats, yachts, and marine structures Deck fittings, hatches, and hardware installations Elastic, vibration-resistant joints above and below deck Bonding wood, metals, primers, coatings, ceramics, and GRP plastics Important Notes Not suitable for plastics prone to stress cracking such as Plexiglas or Polycarbonate Surfaces must be clean, dry, and free from grease or dust before application Recommended application temperature: 5°C to 40°C Technical Details Chemical Base 1-component polyurethane Colour Black Cure Mechanism Moisture-curing Density (uncured) Approx. 1.3 kg/L Shore A Hardness 40 Tensile Strength 1.8 MPa Elongation at Break 500% Temperature Resistance -50°C to +90°C (up to 180°C short term) Skin Time Approx. 60 minutes Shelf Life 12 months (stored below 25°C) Packaging 150 mL Tube For marine sealing and bonding you can trust, Sikaflex®-291 delivers professional-grade strength, flexibility, and durability on every project.
$20.52 $0.14/ml
Selleys Kwik Grip Crystal Clear applies clear and dries crystal clear for less mess and invisible bond lines. Excellent for achieving a neat, clear finish when bonding large, flat close-fitting surfaces such as veneers and laminates for bench or table tops. Forms a durable, heat and water-resistant bond. Features Solvent based contact adhesive Applies clear and dries crystal clear Strong, durable bond on broad surfaces Easy to spread Heat resistant – up to 80°C Water resistant Where can this product be used? Applications where invisible bond lines are needed such as adhering decorative strips to a mirror Bonding veneers of timber and laminated plastics (e.g. Laminex and Formica) to bench or table tops Patching vinyl flooring or replacing a vinyl tile Cork tiling and laying a vinyl floor Fixing shoes or laminate to tables, benchtops, etc. Leather shoe and leather repairs, handbags, and leather work Adhering flexible or other materials to aluminium Joining or repairing holes in tents, car covers, and other outdoor equipment Seek advice of vinyl flooring manufacturers prior to use with their products as discolouration and bubbling can occur with some types. If in doubt, Kwik Grip Waterbased is safe to use for all these applications and will provide excellent bonding. Not suitable for bonding rough, ill-fitting surfaces. Consider using alternative products such as Selleys Liquid Nails for these applications. What materials is this product suitable for? Veneers Rubber Cork Felt Leather Canvas Metals Timber How to use this product Use only in a well-ventilated area. Contact Bonding Hold down lid while opening can. Ensure surfaces are clean and dry. For porous surfaces, apply a thin coat to seal surface and allow to dry for approx. 40 minutes. Using an applicator, completely cover both surfaces with adhesive and keep apart until touch dry (approx. 15 minutes, no more than 30 minutes). Position items carefully, still keeping surfaces apart with dowels. When edges are perfectly aligned, remove dowels and press surfaces firmly together from one edge to the other. Secure the bond by running a roller over the bonded surfaces or by hammering from the centre outwards using a padded block. Maximum bond strength is reached after 24 hours. Clamping may be necessary for warped or curled surfaces. Wet Bonding (for small areas or porous surfaces) Ensure surfaces are clean and dry. Apply Kwik Grip to one surface, then bring the surfaces together and clamp until dry. Handy Tips Test plastics before use as solvents may attack some polystyrene and sheet vinyls. 500mL covers up to 2.5m² of one surface, depending on porosity. For vertical surfaces use Selleys Kwik Grip Vertical Gel. For confined or low-ventilation areas, use Selleys Kwik Grip Waterbased, which is non-toxic and fume-free. Use a brush, knife, or serrated scraper for application. Bonding is immediate once the two surfaces are joined. Keep container sealed when not in use. Surface Preparation and Cleanup For porous surfaces, clean with Selleys Liquid Sugar Soap. For non-porous surfaces (e.g. glass or metal), clean with mineral turpentine followed by methylated spirits. For old paint or residue, use Selleys Kwik Strip Smart and ensure surface is dry before applying adhesive. While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools can be cleaned by soaking in toluol or lacquer thinner. Keep Selleys Sugar Soap Wipes handy for quick cleanup. Safety: Contains highly flammable solvents. Ensure all fire precautions are observed. As an alternative, Kwik Grip Waterbased is non-flammable.
$11.34
Bring Your Leather Items Back to Life Restore your favourite leather goods such as shoes, belts, bags, and upholstery with confidence using Bostik Leather Repair Glue. This precision adhesive delivers a strong, flexible, and water-resistant bond that dries crystal clear. Key Features Ultra strong and long lasting bond for real and imitation leather Flexible and clear finish with no visible residue Resistant to water and heat up to approximately 60 °C Precision application through fine nozzle squeeze tube Multi material versatility suitable for leather, PVC, felt, canvas, some plastics, wood, and metal How to Use Ensure surfaces are clean, dry, and free from dust, oil, or old adhesive residue. For leather surfaces, avoid applying to the shiny side to prevent marks. Apply a thin film of glue to one surface. For non porous materials, apply to both surfaces. Press the surfaces together firmly. The bond sets almost instantly and reaches full strength in about 24 hours. Replace the cap immediately after use to prevent the tube from drying out. Tips and Care For best adhesion, lightly roughen smooth or shiny surfaces with fine sandpaper before gluing. Avoid stressing the repair before full cure. To remove unwanted glue, use acetone or nail polish remover on a small hidden area first. Technical Specs and Safety Form: Clear solvent based polyurethane adhesive Heat resistance: up to approximately 60 °C Highly flammable. Keep away from heat, sparks, and flame. Always follow manufacturer instructions and safety guidance. Use in a well ventilated area, wear protective gloves, and avoid contact with skin or eyes. Packaging Size: 20 mL tube
$15.00
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$28.82
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$25.54
Earl’s Wood Hardener - Restore Soft, Rotted Timber Like New Bring weakened, decayed timber back to life with Earl’s Wood Hardener. This water-based consolidator penetrates deep into soft, rotted fibres and bonds them into a tough, stable base that’s ready for filling, sanding, and painting. Use it to save windowsills, frames, posts, decking boards, furniture, fences, and more—without costly tear-outs or replacements. Why Customers Love It Repairs instead of replacing: Restores soft, crumbly timber to near original strength so you can patch and repaint. Water-based formulation: Low odour, no volatile organic compounds, and non-toxic when cured. Ready to use: Pre-mixed; just shake and apply—no diluting or measuring. Works inside and out: Ideal for interior and exterior timber exposed to weathering. Versatile application: Pour, brush, spray, or syringe to saturate deep into affected areas. Long shelf life: Stays usable for extended periods when stored correctly. Proudly Australian made: Developed for local conditions and everyday DIY and trade use. Where to Use Window sills and sashes, door frames, posts, fences, balustrades, fascia boards, decking edges, outdoor furniture, indoor furniture, trims, mouldings—any non-structural timber showing soft rot or fibre breakdown. How It Works The thin, penetrating formula wicks into softened timber fibres. As it cures, it binds those fibres together to form a firm, stable base that can be filled, sanded, and coated. No need to carve out all the rot—thorough saturation does the heavy lifting. Directions Prep: Ensure the area is dry. Remove dirt, dust, grease, loose paint, varnish, and flaky wood. Mask adjacent finishes if needed. Apply: Shake well. Generously pour, brush, spray, or syringe the hardener into the affected timber. Repeatedly saturate to drive product deep into fibres. Cure: Allow to cure until solid and no longer tacky to the touch. Extremely soft timber may need multiple treatments. Repair: Fill voids with a compatible wood filler, let set, then sand smooth. Finish: Prime/seal and paint or coat as desired. Pro Tip For deep penetration around a localized patch of rot, mark approximately 75 mm either side of the soft area and drill small holes between those points. Brush, spray, or syringe the hardener into the holes until saturation is achieved. Clean-Up & Safety Clean tools and drips with water while wet. Use above 7 °C and in well-ventilated areas. Non-toxic when cured. Always follow label directions and keep out of reach of children. Compatibility Once cured, the hardened substrate accepts most timber fillers and putties. After filling and sanding, it can be primed and top-coated with typical timber paints and finishes. Always test on a small area for compatibility. Limitations Not for structural load-bearing repairs. Not recommended for constant water immersion or areas that cannot be dried prior to application. Timber must be reasonably sound after consolidation; heavily degraded material may require multiple treatments or replacement. Specifications Type Water-based timber consolidant / hardener Use Restoring soft, rotted, non-structural timber prior to filling and painting Appearance Low viscosity liquid; dries clear/transparent Odour / VOC Low odour; no volatile organic compounds Application Methods Pour, brush, spray, or syringe to saturate fibres Interior / Exterior Suitable for both Minimum Application Temperature Above 7 °C Cure Indicator Ready for filling when firm and not tacky to the touch Clean-Up Water while wet Shelf Life In excess of 2 years when stored sealed in a cool, dry place Substrates Soft or rotted timber (non-structural), interior and exterior Country of Manufacture Australia Packaging Ready-to-use container What’s in the Box Earl’s Wood Hardener (ready to use) Storage Keep container tightly closed. Store upright in a cool, dry location away from freezing and direct heat. Do not allow product to dry out in the container. Disposal Allow residual product to cure before disposal. Follow local waste regulations. Important Notes Always read and follow the product label before use. Test on a discreet area to confirm adhesion and finish compatibility. The consolidated timber is not structural and should not be relied upon for load-bearing applications.
$27.95 - $179.95
Crommelin Hybrid MS Polyurethane Flexible Sealant 300ml Take on interior and exterior sealing with a professional grade hybrid MS polyurethane. This single component sealant delivers a flexible, durable seal on common building substrates and is suitable for a wide range of construction and maintenance tasks. Key benefits Very low VOC and isocyanate free UV resistant for long term outdoor performance High flexibility to accommodate joint movement Excellent adhesion on properly prepared porous and non porous surfaces Easy to gun, tool and clean up Typical applications Construction and expansion joints Perimeter sealing around windows and doors Roofing and cladding laps, flashings and penetrations General gap sealing in wet and dry areas Suitable substrates Concrete, masonry, brick and render Timber and fibre cement Metals and coated metals Many plastics* and glass *Always pre test for compatibility and adhesion. Surface preparation Surfaces must be clean, dry, sound and free of dust, oil, release agents and loose material. Remove old sealant and contaminants. Abrade dense or glossy surfaces if required. Use suitable primer if specified for difficult or highly porous substrates. Mask edges for neat joints and install closed cell backing rod where needed to control joint depth. Application Cut nozzle to required bead size and load cartridge into a quality caulking gun. Gun a continuous bead into the joint ensuring full contact with sides and backing. Tool off with a moistened spatula for a smooth finish before skin forms. Protect from water and disturbance during initial cure. Clean up Clean tools and fresh spills promptly. Once cured, remove by mechanical means. Good to know Low odour formulation suitable for indoor use with ventilation. Paintable with many water based coatings once skinned and cured. Always test first. Store upright in a cool, dry place. Keep out of direct sunlight. Safety Wear suitable gloves and eye protection. Avoid contact with skin and eyes. If contact occurs, rinse with clean water. Refer to the product Safety Data Sheet for full precautions. What’s in the box 1 x 300ml cartridge 1 x application nozzle
$16.45
![Sika Sikaflex 252 High Strength Structural Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/7612895456188_c10ea96d-b0be-41ba-a0ee-9656fab35b16.jpg?v=1754711652&width=645)
![Sika Sikaflex 252 High Strength Structural Adhesive Sealant [Black] (2)](http://gluesaustralia.com.au/cdn/shop/files/sika-sikaflex-252-high-strength-structural-adhesive-sealant-black-2.jpg?v=1792406707&width=645)
Elastic adhesive for vehicle assembly bonding Sikaflex®-252 is an elastic 1-component polyurethane adhesive especially designed for bonding large components in vehicle assembly. It is suitable for bonding coated metal, GRP, ceramic materials and plastics. Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties PRODUCT BENEFITS Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties Can be painted Vibration-damping Electrically non-conductive Usage Sikaflex®-252 is suitable for assemblies that are subject to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminum (including anodized components), sheet steel (including phosphated, chromated and galvanized components), metal primers and paint coatings (2-component systems), ceramic materials and plastics. Seek manufacturer’s advice before using on plastics that are prone to stress cracking. This product is suitable for professional experienced users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
$53.62
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work. Uses SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include: Wood Stone Metals Glass Ceramics Concrete Brick Masonry Advantages Waterproof Resistant to solvents and chemicals Paintable with water based and solvent based paints High adhesion strength Storage and Shelf Life Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous). Application Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations. Colour: Brown Density 1.11 kg/litre approx. Bond Strength Tensile Strength - 3030kpa Test Substrate - Timber: End grain to end grain Viscosity 6,000cps Handling Precautions Avoid contact with skin and eyes. Wear protective gloves and eye protection during work. If skin contact occurs, wash skin thoroughly. If in eyes, hold eyes open, flood with warm water, seek medical attention without delay. A full Material Safety Data sheet is available from Sika on request.
$24.20
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. Features: CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More Directions All surfaces must be clean and tight fitting. Clear Gorilla Glue will stain clothes. 1. Damp It For non-porous surfaces only (i.e. metal, glass, plastics), lightly dampen one surface with water. Do not add water to the bottle. 2. Glue It Apply Clear Gorilla Glue to surfaces. Best at room temperature. 3. Clamp-It Clamp objects together for 2 hours. Full cure in 24 hrs. You can use heavy objects to achieve clamping pressure. *Not recommended for use on polyethylene or polypropylene plastics. Storage Tips After each use, wipe nozzle clean with a dry cloth and tightly replace lid. Store in a cool, dry place with exposure to light. Lack of light and heat can cause the product to yellow. Cured glue can be removed from work surface with chisel, scraper or sandpaper. Store away from children and animals. Specs: APPLICATION TEMPERATURE – 32° to 100° F, best at room temperature SERVICE TEMPERATURE – -20° to 180° F OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – No FAQS What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight-fitting joints. It’s perfect for a fix you need doing fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also gap filling which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant and can withstand intermittent exposures, however, is not meant for a constant soak. Original or White Gorilla Glue is 100% waterproof and can withstand soaking and longer-term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$29.94
Loctite Vinyl, Fabric & Plastic Flexible Adhesive is a clear, single-part liquid glue made for mending rips, tears and splits in flexible materials. It dries to a transparent, waterproof bond that stays bendable, so repairs to vinyl, fabric and many plastics flex with the item instead of cracking, and the clear finish lets you avoid unsightly patches or tape. Formula overviewThis is a polyurethane-based adhesive supplied as a clear, low-viscosity liquid in a 30ml (1 fl oz) squeeze tube. It cures by solvent release to a flexible solid that resists water once fully set. The bond will not go brittle with age, although prolonged exposure to sunlight can cause some yellowing over time. Where to use itIndoors: vinyl upholstery and seat covers, cushions, raincoats and other wet-weather clothing, shoes, weather stripping, toys and general household items made from vinyl, fabric, leather and rubber.Outdoors: tarps, camping and outdoor gear, beach balls, inflatable mattresses and wading pools, wherever a waterproof and flexible repair is needed. It bonds a wide range of substrates, including vinyl (PVC), fabric, leather, rubber, canvas, paper, wood, glass, metal, ceramic and many flexible plastics. How to useWork in a well-ventilated area and make sure both surfaces are clean, dry and free of oil, grease, wax and paint. Lightly roughen very smooth surfaces so the glue can grip. Pierce the foil seal in the head of the tube using the reverse end of the cap.Small tears: apply along both edges of the damage, press together and hold with masking tape for around two hours.Larger tears: place a cloth or fibreglass patch behind the damaged area for extra strength, apply along the edges, then tape the repair for around two hours.Contact method: coat both surfaces, leave for 10 to 30 minutes until touch-dry, then bring the parts together within 30 minutes. Allow a full 24 hours of cure before exposing the repair to water. Wipe away wet excess before it sets, and trim cured residue carefully with a sharp blade. Important notesDo not use on polyethylene (PE), polypropylene (PP), PTFE, PET, polystyrene foam board or polyformaldehyde.Do not use on rubberised or coated cotton, foam rubber, neoprene or urethane rubber.Not suitable for faux leather or leatherette.Not recommended where the repair will be exposed to temperatures above 60°C.Clean up uncured adhesive with acetone, following the solvent maker's precautions, as acetone can damage some plastics and is highly flammable. Specifications Brand Loctite Type Polyurethane flexible repair adhesive Size 30ml (1 fl oz) Colour Clear Form Liquid, carded squeeze tube Density 0.820 to 0.900 Viscosity 2250 to 2750 cps Open time 10 to 30 minutes Full cure 24 hours Application temperature 5°C to 30°C Service temperature Up to 60°C Flash point -9°C VOC content Up to 80.8 g/L (CARB) Water resistance Waterproof once cured Shelf life 24 months unopened Clean up Acetone (uncured) SafetyContains methyl ethyl ketone. The vapour is harmful and may cause dizziness, headache or nausea and may affect the nervous system. The product is a skin sensitiser and can irritate the eyes, skin and respiratory tract. Use only in a well-ventilated area, keep away from heat, sparks and open flame, do not smoke while using it, and keep the container closed when not in use. Refer to the Safety Data Sheet (SDS) for full details.
$14.08
Repair flexible plastic items easily with Bostik Soft Plastics Glue. This clear, quick-drying adhesive creates a strong yet flexible bond that withstands stretching, bending and movement, making it perfect for repairing soft plastic and vinyl materials around the home, outdoors or on the go. Ideal for Inflatable toys, air mattresses and pool liners Vinyl upholstery, raincoats and tarps Plastic footwear, shower curtains and coated fabrics Features and Benefits Dries clear for neat, invisible repairs Flexible and waterproof once cured Strong, long-lasting bond for soft PVC and vinyl Easy to apply directly from the tube Directions Ensure surfaces are clean, dry and free from grease or dust. Apply a thin, even layer of glue to both surfaces. Press together firmly and allow to dry for 10–15 minutes. For best results, leave for 24 hours to achieve full bond strength. Clean Up Wipe away excess adhesive with a clean cloth before it sets. Once cured, mechanical removal may be required. Safety Information Use in a well-ventilated area. Avoid contact with skin and eyes. Keep out of reach of children.
$12.98
![Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240085.jpg?v=1754724137&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$35.34 - $39.95
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524002800_e901daee-d941-4c51-bb2c-fdfedd9a6316.jpg?v=1754711662&width=645)
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/sikaflex-sika-227-automotive-sealant-fast-curing-non-sagging-310ml-white-2.jpg?v=1792406669&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$31.92
![Sika Sikaflex 291 Marine Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb9d6399-3f9c-4c6e-aeb9-97604f6829a6.jpg?v=1754711703&width=645)
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck. Why Choose Sikaflex®-291 Excellent adhesion to common marine substrates Good ageing & weathering resistance for long service life Elastic to absorb vibration and movement Low odour and non-corrosive Overpaintable and sandable after cure* Available colours: White, Grey, Black *Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area. Typical Uses Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications. Suitable Substrates Wood Metals, metal primers and 2-component paint systems Ceramic materials Plastics such as GRP (fibreglass), etc. Do Not Use On Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate) Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility. Technical Data (Typical) Property Method / Note Value Chemical base — 1-component polyurethane Cure mechanism — Moisture-curing Colour CQP001-1 White, Grey, Black Density (uncured) — ~1.3 kg/L (colour-dependent) Non-sag properties — Good Application temperature Ambient 5 – 40 °C (optimum 15 – 25 °C) Skin time CQP019-1 (A) ~60 minutes Open time CQP526-1 (A) ~45 minutes Curing speed CQP049-1 Depends on temperature & humidity (see TDS) Shrinkage CQP014-1 ~5 % Shore A hardness CQP023-1 / ISO 48-4 ~40 Tensile strength CQP036-1 / ISO 527 ~1.8 MPa Elongation at break CQP036-1 / ISO 527 ~500 % Tear resistance CQP045-1 / ISO 34 ~6 N/mm Service temperature (continuous) CQP513-1 −50 to +90 °C Service temperature (short-term) CQP513-1 +160 °C (4 h), +180 °C (1 h) Shelf life (B) 12 months (store < 25 °C) CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C. Application Guidance Surface Preparation Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates. Application Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity. Optimum substrate and product temperature is 15 – 25 °C. Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment. Tooling & Finishing Tool within the skin time. Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability). Cleaning & Removal Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent. Cured material: remove mechanically (e.g. knife, wire, abrasion). Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin. Overpainting Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting. If the paint requires baking > 80 °C, allow the sealant to fully cure first. Always conduct preliminary trials under manufacturing conditions. Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area. Compliance & Approvals Meets requirements set out by the International Maritime Organization (IMO). Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable. FAQs Can Sikaflex®-291 be overpainted? Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area. What is a “marine grade” sealant/adhesive? Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline. When and why should a primer be used? Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing. What does the Wheelmark indicate? The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED). Which substrates does Sikaflex®-291 bond to? Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate). How do I remove Sikaflex®-291? Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material. Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
$28.97
Showerbond is a solvent based, fast grab, gun grade adhesive. It has been specifically formulated for bonding plastic shower linings to gypsum plasterboard or fibre cement wall linings, as well as timber. Use Showerbond is used for bonding plastic shower linings to wall linings. Advantages Fast curing. Will not damage plastic shower liners. Panels can be relocated for up to 30 minutes after positioning. Excellent adhesion to most common building materials. Easy to apply and clean up. Recommended for use with Seratone Silverseal, Clearlite Showers, Duracryl® ,and Athena Showers Product Data Form: Smooth paste Colour: Green Storage & Shelf Life: Twelve (12) months when stored in original unopened containers in a cool, dry place away from naked flames. Packaging: Showerbond is supplied in 300 ml cartridges. Technical Data Solids content: 65% approx. by weight Cure type: Solvent release Cure rate: 24 hours @ 20C Application temperature: 5C to 35C Skinning time: 1 minute Relocation time: Up to 30 minutes, depending on temperature and ventilation Flammability: Flammable solvents are released during cure Toxicity: Non toxic when cured Movement accommodation: Slight, will accept normal building movement Coverage: On average, one cartridge of Showerbond will supply 20 metres of 5 mm bead. Application Conditions Surface Preparation Ensure both surfaces to be bonded are clean, dry and grease free. Cut nozzle on cartridge as shown below so that a 5-6 mm bead will be extruded. Application Apply a 5-6 mm bead in vertical lines at 100 mm centres onto substrate, and apply continuous bead within 15 mm of the perimeter line of the shower lining. Place shower lining onto wall within 10 minutes and firmly press the entire sheet with your hands so that full contact is made with all beads of adhesive. Brace the lining as required in the shower manufacturer's installation instructions. Bracing if required should remain in position for not less than 18 hours. The shower should not be used for at least 24 hours after the wall lining has been installed. Do not apply blobs of adhesive. These will cause unsightly undulations and buckles in the sheet.
$21.37
Selleys Liquid Nails Exterior: The Builder's Choice for Durable Outdoor Bonds Key Features Adheres up to 3 tonnes per m² after just 4 hours on timber Water, heat, and UV-resistant Long-lasting bond that won't crack or go brittle Fast and easy water clean-up Compliant with Australian Standard AS 2329(1999) and Green Building Council VOC limits Suitable Materials This adhesive is ideal for the following materials: Timber Plasterboard MDF LOSP Treated Timber Concrete Masonry Plastics (pre-test for compatibility) Tiles Glass Ceramics Directions for Use Follow these simple steps for optimal performance: Ensure surfaces are clean and free from grease or loose particles. Cut cartridge tip, fit nozzle, and cut to 5mm opening. Apply adhesive along the material's length or in beads on flat surfaces. Press pieces firmly together, securing with fasteners or clamps. Allow to set for a minimum of 4 hours before removing any temporary fasteners. Limitations Not suitable for use on PFTE, PE, or PP. Cleaning & Safety Clean up is easy with warm soapy water or a damp cloth for wet adhesive, and a scraper or sandpaper for dried adhesive. Product Specifications Available in 350g cartridges, in white color, and uses Self-crosslinking acrylic technology.
$12.00
Selleys Brick and Concrete Silicone is a neutral (non-corrosive) cure 100% silicone sealant. It is low modulus or can be stretched easily, which makes it ideal for joints which will move significantly such as expansion joints in concrete, and is grey so it will blend in with the concrete surrounds. Features Superior flexibility +/- 25% movement capability & up to 500% elongation or stretch. Superior silicone formulation forms a durable seal which locks out water and which does not shrink when drying. UV and weather resistant – Immune to the damaging effects of the sun. Temperature resistance – approximately -60°C +150°C. Superior adhesion to concrete and fibre cement surfaces. Low odour so can be used in any environment without discomfort. 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Grey Appearance Smooth Where can this product be used? joints in brick walls expansion joints in concrete Perfect for use on or around: Walls Patios Floors Fencing Windows Expansion joints in concrete. Can not be painted over. Not suitable for use in below waterline applications. Do not use in below ground applications. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Bricks and mortar Ceramics and porcelain Concrete Fibre cement Marble & stone Metal Wood Many plastics including polystyrene How to use this product Throughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow to dry completely before applying silicone. If there old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenous product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course grain, as the silicone will adhere more readily to a scratched up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipes. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see a handy tip. The sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. Handy tips Tips for Using a Brick & Concrete Silicone Sealant Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safetytips Uncured product may irritate eyes. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use keep the nozzle on the cartridge Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$19.79
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/9310492265001_6fb5fccc-7784-41bb-9997-bbd917e3c834.png?v=1754712704&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$22.51
Bastion Bond Breaker Joint Sealant Professional silicone bond breaker for wet areas. Create a flexible, waterproof separation at wall to wall and wall to floor junctions so your membrane and tile system can move without cracking. Ideal for bathrooms, showers, laundries and balconies. Why choose this sealant Permanently flexible to absorb movement in corners and junctions Neutral cure silicone suitable for use with most waterproofing membranes Low odour, low VOC, indoor use friendly Excellent adhesion to common building materials including concrete, masonry, ceramic tile, porcelain and most metals Water resistant once cured and designed for wet area applications Easy to gun out and tool for a smooth finish Typical uses Forming a bond breaker fillet in shower bases, bathrooms and laundries before waterproofing Movement joints at internal corners prior to tiling General wet area sealing where a flexible joint is needed Surface preparation Ensure surfaces are clean, dry and free from dust, oil, loose material and old sealant. Mask adjacent edges for a neat finish if required. For wide gaps, insert backing rod to control sealant depth. How to apply Cut the cartridge nozzle to the desired bead size and load into a standard caulking gun. Gun a continuous bead into the corner or joint. Aim for a smooth cove fillet in the 5 to 12 mm range. Tool the bead with a spatula or rounded tool to compact and shape it. Remove masking tape while the sealant is still wet. Allow the bond breaker to skin before applying compatible waterproofing membranes over the area. Follow your membrane manufacturer’s recoat time. Cure and finishing Skin time is typically minutes depending on temperature and humidity. Full cure occurs over 24 to 48 hours for standard beads. Thicker sections require longer. After the membrane has cured, complete tiling and finish perimeter joints with a sanitary grade silicone. Clean up Wipe away excess immediately with a clean cloth. Once cured, remove mechanically by trimming and peeling. Handy tips Not paintable. If painting is required, paint adjacent surfaces before sealing. Always use backing rod for large joints to control sealant depth and reduce three sided adhesion. Pre test on sensitive or natural stone surfaces. Do not use in continuously immersed conditions or for structural glazing. Storage and packaging Cartridge size: 300 mL Store upright in a cool, dry place. Use before the best by date printed on the cartridge. Safety Use in a well ventilated area. Avoid contact with skin and eyes. Keep out of reach of children. Refer to the product label for first aid directions. In the box 1 x 300 mL cartridge of Bastion Bond Breaker Joint Sealant 1 x application nozzle
$11.94
Sikaflex 258 Primerless Glass Adhesive 310 mL is a reliable polyurethane glass adhesive designed for primerless bonding to suitable automotive glass chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 310 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Sikaflex 258 for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Sikaflex 258 Primerless Glass Adhesive 310 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bonding glass where a primerless system is specified Automotive and transport glazing carried out by trained users Suitable surfaces The adhesive works well on the following surface types when properly prepared: Compatible glass substrates Painted frames and prepared bodywork per Sika guidance Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of observe skin time and install components within this window. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Moisture cure technology forms a strong, elastic bond. Skin forms first, followed by through cure depending on joint depth and humidity. Temperature and environmental performance Do not apply below the minimum stated on pack. Maintain adequate humidity for moisture cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Remove fresh adhesive with suitable cleaner. Once cured, trim with a sharp blade using care. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store cartridges cool and dry. Check use by dates before installation in critical work. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$37.49
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$27.72
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work. Uses SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include: Wood Stone Metals Glass Ceramics Concrete Brick Masonry Advantages Waterproof Resistant to solvents and chemicals Paintable with water based and solvent based paints High adhesion strength Storage and Shelf Life Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous). Application Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations. Colour: Brown Density 1.11 kg/litre approx. Bond Strength Tensile Strength - 3030kpa Test Substrate - Timber: End grain to end grain Viscosity 6,000cps Handling Precautions Avoid contact with skin and eyes. Wear protective gloves and eye protection during work. If skin contact occurs, wash skin thoroughly. If in eyes, hold eyes open, flood with warm water, seek medical attention without delay. A full Material Safety Data sheet is available from Sika on request.
$15.39
SikaTitan® 258 is a primerless to windscreen, one-component direct glazing adhesive. It is easy to apply and has a paste-like consistency. On exposure to atmospheric moisture it cures to a durable elastomer. SikaTitan® -258 provides a long tack-free time and ensures a safe application even under warm conditions. Note: Primerless application requires the glass to be prepared with a non-antistatic glass cleaner. Also the bonding surfaces must be free of contamination prior to the application of the adhesive. SikaTitan® -258 is manufactured in accordance with ISO 9001 / 14001 quality assurance system and with the responsible care program. Product Benefits - Primerless to glass - One-component formulation - Cold application - Good application properties such as bead stability / good non-sag properties - Short cut-off string - Tested according to FMVSS 212/208 (with double-side airbags, no seatbelts) Areas of Application SikaTitan® -258 is suitable for direct-glazing applications in the Automotive Glass Replacement business. With its good performance and application properties it is suitable for mobile as well as inhouse installations.This product is to be used by professional experienced fitters only. If this product is used for other applications than Automotive Glass Replacement, trials must be carried out prior to use. Technical Product Data Chemical base 1-C polyurethane Colour (CQP1) 001-1) Black Cure mechanism Moisture-curing Density (uncured) (CQP 006-4) 1.1 kg/l approx. Non-sag properties (CQP 061-1) Good Application temperature +5 to +40°C Skin time2) (CQP 019-1) 40min. approx. Open time2) (CQP 526-1) 30min. approx. Curing speed(CQP 049-1) Shore A hardness (CQP 023-1 / ISO 868) 51 approx. Tensile strength (CQP 036-1 / ISO 37) 5 MPa approx. Elongation at break (CQP 036-1 / ISO 37) 650% approx. Tensile lap-shear strength (CQP 046-1 / ISO 4587) 2.5 MPa approx. Safe Drive-Away Time2) (cars) with double side airbag according to FMVSS 212 / 208 (CQP 511-1) without airbag 6 hours 2 hours Chemical Resistance SikaTitan® -258 is resistant to fresh water, seawater, limewater, sewage effluent, diluted acids and caustic solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic acids and caustic solutions or solvents. Method of Application Removal of old glass Remove damaged glass in accordance with the vehicle manufacturer’s instructions. Surface preparation Surfaces must be clean, dry and free from dust and grease. The bond faces must be prepared with a non-antistatic glass cleaner. Bonding surface must be free of contaminants before application of the product. Windshields without ceramic coatings need additional UV protection. Application Cut off the tip of the nozzle in accordance with the vehicle manufacturer's recommendations and screw onto the cartridge. It is recommended to apply the adhesive with a piston-type application gun. To ensure a uniform thickness of adhesive bead, we recommend that the adhesive be applied in the form of a triangular bead (see fig. 1 below). The substrate temperature must be between 5°C and 35°C.
$44.46
![Sika Sikaflex 291 Marine Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb4dfb0d-a336-4739-9b91-9ca89764b874.jpg?v=1754711704&width=645)
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck. Why Choose Sikaflex®-291 Excellent adhesion to common marine substrates Good ageing & weathering resistance for long service life Elastic to absorb vibration and movement Low odour and non-corrosive Overpaintable and sandable after cure* Available colours: White, Grey, Black *Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area. Typical Uses Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications. Suitable Substrates Wood Metals, metal primers and 2-component paint systems Ceramic materials Plastics such as GRP (fibreglass), etc. Do Not Use On Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate) Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility. Technical Data (Typical) Property Method / Note Value Chemical base — 1-component polyurethane Cure mechanism — Moisture-curing Colour CQP001-1 White, Grey, Black Density (uncured) — ~1.3 kg/L (colour-dependent) Non-sag properties — Good Application temperature Ambient 5 – 40 °C (optimum 15 – 25 °C) Skin time CQP019-1 (A) ~60 minutes Open time CQP526-1 (A) ~45 minutes Curing speed CQP049-1 Depends on temperature & humidity (see TDS) Shrinkage CQP014-1 ~5 % Shore A hardness CQP023-1 / ISO 48-4 ~40 Tensile strength CQP036-1 / ISO 527 ~1.8 MPa Elongation at break CQP036-1 / ISO 527 ~500 % Tear resistance CQP045-1 / ISO 34 ~6 N/mm Service temperature (continuous) CQP513-1 −50 to +90 °C Service temperature (short-term) CQP513-1 +160 °C (4 h), +180 °C (1 h) Shelf life (B) 12 months (store < 25 °C) CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C. Application Guidance Surface Preparation Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates. Application Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity. Optimum substrate and product temperature is 15 – 25 °C. Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment. Tooling & Finishing Tool within the skin time. Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability). Cleaning & Removal Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent. Cured material: remove mechanically (e.g. knife, wire, abrasion). Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin. Overpainting Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting. If the paint requires baking > 80 °C, allow the sealant to fully cure first. Always conduct preliminary trials under manufacturing conditions. Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area. Compliance & Approvals Meets requirements set out by the International Maritime Organization (IMO). Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable. FAQs Can Sikaflex®-291 be overpainted? Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area. What is a “marine grade” sealant/adhesive? Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline. When and why should a primer be used? Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing. What does the Wheelmark indicate? The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED). Which substrates does Sikaflex®-291 bond to? Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate). How do I remove Sikaflex®-291? Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material. Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
$28.97
SikaBond®-145 SuperGrip Premium polyurethane construction adhesive with fast build up of Strength SikaBond®-145 SuperGrip is a premium grade one-component polyurethane construction adhesive with good initial grab and high strength after 30 minutes^. SikaBond®-145 SuperGrip is a versatile, ready to use, fast curing, general purpose construction adhesive suitable for interior and exterior use. One-component. Interior & exterior. Non-shrink. Usage SikaBond®-145 SuperGrip is suitable for use in construction and repair applications where a permanent strong bond is required between porous-nonporous surfaces. SikaBond®-145 SuperGrip is suitable for bonding most common construction materials such as: Wood MDF Concrete Brick Metal Polystrene Polyurethane foam Some PVC Marble Granite Ceramic LOSP Timber Advantages One-component. Interior & exterior. Non-shrink. Non-sag. High initial grab. Adheres rapidly. Stong bond in 30 minutes^. Fast cure. Solvent-free. Resistant to heat. Resistant to weathering. Water resistant -D4 according to DIN En 204 Applies white, can dry translucent if applied in thin layers.
$24.15
Selleys Liquid Nails Rapid Cure is an advanced, high-performance polyurethane construction adhesive that cures in just 10 minutes*. It provides a durable, waterproof bond even when bonding two non-porous surfaces. Features Fast cure in 10 minutes*. More than twice the strength of conventional solvent-based construction adhesives. Waterproof – Uncompromising durability, with excellent water, weather and heat resistance. Can be used to bond most materials, and for most interior & exterior applications. Its advanced formulation exceeds the requirements of BS-EN204 D4 for durability. Resistant (after full cure) to heat to 100 degrees C and cold to -30 degrees C. See “Limitations” below. Does not drip, sag or string between panels. Bridges gap up to 5mm hence can be used on rough and ill-fitting construction materials. Product expands slightly as it cures. The dried adhesive is paintable. *Expect longer times for very dry timber, heavier objects and less porous surfaces or in colder weather. *Limitations – Not suitable for sole fixing or structural bonding. Where can this product be used? Liquid Nails Rapid Cure can be used for applications where higher performance characteristics are necessary. These include applications where: Extra water resistance is essential. eg. Exterior applications such as decking. Extra strength is required. Extra temperature resistance is required. eg. Applications where metal substrates are exposed to direct sunlight. Plastic substrates which are sensitive to solvent-based adhesives are used. Metal installations in which solvent-based adhesives will be slow to cure. Liquid Nails Waterproof is also suitable for typical construction applications such as: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite What materials is this product suitable for? Timber MDF Plasterboard Plastics (Pre-test to determine suitability) Masonry Concrete Particleboard Metals Rubber Tiles LOSP treated pine How to use this product General Avoid contact with skin. Wear safety glasses, impervious gloves and clothing. Surfaces to be bonded should be free of oil, grease and dust. On wet timber pooled water should be wiped off. 1. Cut cartridge tip, fit nozzle and cut end to desired width (approx 5mm diameter). 2. Apply bead along the length of one bonding surface. On broad surfaces apply beads every 40cm. (‘zig-zag’ beads are more appropriate on surfaces of moderate width; eg shiplap panels.) 3. Position pieces and press firmly together. Fix with sufficient nails, screws or clamping to hold the load and achieve contact over the total bond area. Repositionable for up to 5 mins after fitting. 4. Allow to set for 15-20 mins for porous surfaces before removing temporary fasteners or clamps.* Liquid Nails Rapid Cure will achieve a full cure in 24 hours. *Expect longer times for very “dry” timber, heavier objects and less porous surfaces, or in colder weather. Spraying surfaces with a very light mist of water may help speed up the cure. Handy tips Gloves should be worn when applying Liquid Nails Rapid Cure. Avoid contact with skin. Adhesive requires moisture to cure, therefore drying times will vary depending on temperature, humidity and the porosity of materials bonded. Spraying surfaces with a very light mist of water may help speed up the cure. The product should not be applied below 5°C. LIQUID NAILS Rapid Cure expands slightly as it cures. Not suitable for sole fixing for structural bonding. LIQUID NAILS Rapid Cure should always be used in conjunction with mechanical fasteners in structural, critical or high-stress applications. Wet LIQUID NAILS Rapid Cure residues can be removed with acetone or mineral turpentine. Cured or dry LIQUID NAILS Rapid Cure residues can be removed by chiselling, scraping or sanding. SafetyAvoid skin contact. Avoid breathing in vapours. Ensure you use a well-ventilated area The product is an eye, skin and respiratory irritant and can potentially cause irritation. Avoid contamination of waterways. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Store in a cool place. The adhesive should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Liquid Nails Rapid Cure is a polyurethane based adhesive that requires moisture to cure. Wrapping the nozzle in aluminium foil and sealing tightly with tape can prevent moisture exposure for longer storage.
$20.69
Flexiseal FC is a fast curing polyurethane Adhesive and Sealant with high flexibility and excellent adhesion. Waterproof+, suitable for indoor and outdoor applications^, paintable after it has cured. Best for : Common building materials such as concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics*. Product Details Where can this product be used? External wall and cladding joints Weatherproofing joints between brickwork, masonry, wood concrete or metal frames Joints in walls, balconies, around window or door frames Joints in bridge and balcony parapets Retaining walls Roofing Acoustic rated walls What materials is this product suitable for? Common building materials such as concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics*. *Will not adhere to PE, PP or PTFE–test other plastics and rubber first. How to Use AS AN ADHESIVE: Apply a bead or small blobs on surface. Assemble parts together and clamp firmly to hold until cured. Remove excess immediately. Initial bond achieved in 24 hours depending on temperature and humidity. Bond strength increases over a few days. AS A SEALANT: Extrude sealant into the joint ensuring full contact with the sides of joint. Avoid entrapment of air. Smooth sealant with spatula forcing it into the joint. For best performance, install joint backing rod (polyethylene or polyurethane foam rod) in the joint to control depth and ensure joint movement. Suitable for +/- 25% joint movement. Complies with ISO11600/F/25HM. Limitations: *Will not adhere to PE, PP or PTFE–test other plastics and rubber first. ^To maximise durability in outdoor applications paint with a suitable exterior paint. Some colours may discolour after exposure to UV radiation. +Not suitable for permanent water immersion or below water line use. Clean Up Mineral turps. Cured product can only be removed mechanically
$25.37
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
$10.86
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$17.12
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding Features Super Durable High Strength 100% waterproof* – *(not for permanent water immersion) Bonds wood to almost anything Acid & chemical Resistant – PVA’s break down with acid/alkaline contact Versatile can be used to bond surfaces other than wood Heat resistant up to 140 deg Generous working time (10 minutes) Expands as it dries Sandable – easy, will not clog sandpaper like other PVA emulsion glues Paintable Stainable after sanding The product is a brown liquid and turns a light yellow when fully cured Can be used for gap filling Can Also be used to bond surfaces other than wood I.e metal to metal Bonds MDF Non-Toxic (once fully cured) Where can this product be used? Interior and exterior Sauna or cabinet repairs in high heat areas Bonding Timber to other surfaces (metal etc) Cubby House with metal roof & floor lining Planter boxes Steps leading off a verandah Timber letterbox to a metal support frame Window frame Decorative timber to a pergola Interior panels of a boat Repairing wooden boat oars Repairing wooden handles on tools Timber joinery Laminating chopping boards Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice) Cannot be used if application temperature is below 5°C For best results, one surface should be porous Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua Not recommended for structural applications Not recommended for vertical projects due to runny consistency While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming Surfaces should be clamped tightly or weighted What materials is this product suitable for? MDF Glass Metal Concrete Ceramic Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first). All timbers How to use this product Surfaces to be bonded must be close fitting, clean, dust and grease free. Wipe very dry porous surfaces with a damp cloth 1 minute before bonding. Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures. Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured. Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container). Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting. Clean tools with acetone or white turpetine immediatly after use (before adhesive dries). Handy tips 1L covers approx. 8m2 It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin). For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface. The tighter you clamp, the better bond you will obtain (as Durabond expands). Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.) Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive. In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin. If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off. Safetytips Contains organic isocyanate polymers. On contact, uncured adhesive can irritate eyes. Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water. Avoid breathing vapours. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Clean tools with acetone or white spirit immediately after use (before adhesive dried). Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
$34.65
![Davco K10 Plus Waterproofing Membrane 20L [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/davco-k10-plus-waterproofing-membrane-20l-grey-2.jpg?v=1792411411&width=645)
Davco K10 Plus is a premixed, ready-to-use, water-based polyurethane waterproofing membrane for tradies and builders, supplied here as a 20L pail in grey. It is a Class III membrane designed to sit under tile, stone and other resilient finishes on both walls and floors, in domestic and commercial jobs.About the formulaA one-part, water-based polyurethane that goes on straight from the pail with no mixing. It is rated Class III under AS/NZS 4858 and is highly flexible, with elongation above 500%. The manufacturer also lists it as non-toxic, UV stable and suitable as an anti-fracture membrane. Because it is water-based and solvent-free, it suits confined areas. Published technical figures include a Shore A hardness of 72 and a tensile strength of 2.1MPa.Where to use itIndoors: walls and floors in showers, bathrooms and other wet areas, ahead of tiling.Outdoors: terraces, balconies, roofs and walkways that will be covered with a hard finish such as tile.Suitable substrates include concrete, cement render and screeds, lightweight blocks, building boards approved for wet areas (such as compressed fibre cement sheet) and prepared metal surfaces. Metal needs an etching primer. All substrates should be primed with a suitable Sika primer before the membrane goes on.How to use itPrepare the substrate so it is sound, clean and primed. New render or screed needs a wood float finish and should cure before you start. Where falls are not already in place, form them with a sand and cement screed first. Apply the membrane by brush or roller in a minimum of two coats to reach a 1mm dry film. Each coat should go on at a wet film thickness of at least 0.75mm. Let the first coat dry for about 1 to 2 hours, then apply the second coat at 90 degrees to the first. Add further coats if needed to reach the minimum dry film thickness. Tools can be cleaned with water while the product is still wet. Tile over the cured membrane using a Sika polymer-modified cement-based tile adhesive.Important notesAllow about 6 to 8 hours before tiling or applying other finishes. Allow 3 days before flood testing and 5 days before the area returns to service. Drying times vary with temperature, humidity and film thickness. The membrane is not designed to be left exposed, so it must be covered with a finish. Follow the current Sika data sheet for primer selection, bond breakers, corners and joints, and for any movement joints. Wet area waterproofing must be done to the relevant Australian Standards and building code requirements, so use a licensed applicator where required. Shelf life is 12 months from manufacture. Store in a cool, dry place out of direct sunlight and do not let it freeze.Specifications Brand Davco (Sika) Product K10 Plus Waterproofing Membrane Pack 20L pail Colour Grey Base Water-based polyurethane, one part, premixed Classification Class III (AS/NZS 4858) Application Brush or roller Elongation Greater than 500% Coverage Approx. 13.3m² per 20L pail at two coats (1mm dry film) Recoat time 1 to 2 hours Ready for tiling 6 to 8 hours Flood test After 3 days Return to service 5 days VOC content 62g/L Shelf life 12 months from manufacture Use Interior and exterior, under tile, stone and other resilient finishes SafetyEven so, wear gloves and eye protection during application and keep the area ventilated, especially in enclosed spaces. Keep out of reach of children, avoid contact with eyes and skin, and do not let uncured product enter drains or waterways. Store the pail sealed, cool and out of frost. Refer to the Safety Data Sheet (SDS) for full details.
$266.99
![Sika SikaBond T-55(J) Elastic Wood Flooring Adhesive 600ml Foil Pack [Ochre] (2)](http://gluesaustralia.com.au/cdn/shop/files/sika-sikabond-t-55-j-elastic-wood-flooring-adhesive-600ml-foil-pack-ochre-2.jpg?v=1792411222&width=645)
Sika SikaBond T-55(J) is a one-component, elastic polyurethane adhesive for fully bonding solid and engineered timber floors, supplied here as a single 600ml foil pack for smaller flooring jobs and repairs. It spreads easily, stays flexible once cured and helps take the stress out of the bond between the timber and the substrate, which suits floors that need to move a little with the seasons.About the formulaA moisture-curing polyurethane that cures by reacting with humidity in the air, so it needs reasonable ambient moisture to set properly. The cured adhesive is elastic and dampens footfall sound. It is sandable along with the floor, and Sika rates it as low in VOCs. It is approved for use over underfloor heating and can be applied directly onto old ceramic tiles, which can save you from ripping up an existing tiled floor first (do a preliminary adhesion test on glazed tiles).Where to use itIndoors: full-surface bonding of solid timber and engineered timber floors, parquetry and strip panels, mosaic and industrial parquet, and chipboard, over concrete, cement-based screeds, timber subfloors and old ceramic tiles. It can also be used as an underlay layer before timber flooring is laid.Outdoors: not intended for outdoor use, and it is not rated as UV or weather resistant.Suitable substrates include concrete, cement-based floors, chipboard, timber subfloors and ceramic tiles. Sika notes that ground-floor slabs and areas without a damp-proof membrane need moisture protection first (see important notes below).How to use itMake sure the substrate is clean, dry, sound and free of dust, contamination and old coatings or adhesives. Check the substrate moisture content before you start and prime or seal where required. Load the foil pack into a suitable application gun, snip the end and cut the nozzle tip to suit, then lay the adhesive over the floor and spread it evenly with a notched trowel. Sika's current data sheet lists coverage of roughly 600 to 1000 g per square metre depending on the trowel notch and the flooring type. Use a larger notch for long or wide boards and uneven substrates so you get a continuous bed with no hollow spots. Press the timber firmly into the adhesive while it is still wet and keep a 10 to 15mm expansion gap to the walls. Clean tools while the adhesive is uncured, using Sika Remover-208 or Sika Colma Cleaner. Cured adhesive can only be removed mechanically.Important notesSika's data sheet states this product is only suitable for use by professional wood floor applicators. Apply and lay within roughly 15 to 35 degrees ambient and substrate temperature (20 to 35 degrees with underfloor heating), with relative humidity of about 40 to 70 percent. Keep the adhesive at or above 15 degrees for good workability. The floor can be walked on after about 12 hours and sanded after about 24 hours, depending on conditions and adhesive thickness. Do not expose uncured adhesive to alcohol-containing products, as they interfere with curing. Where a ground-floor slab or other area has no damp-proof membrane, follow Sika's moisture-barrier recommendations (Sika Primer MB or MR Fast, or Sikafloor EpoCem) before laying timber. Follow the flooring manufacturer's own installation guidelines as well.Specifications Brand Sika Product SikaBond T-55(J) Elastic Wood Flooring Adhesive Pack 1 x 600ml foil pack Colour Ochre Base 1-component polyurethane, moisture curing Application Foil pack via application gun, spread with a notched trowel Skin / laying time About 60 minutes at 23 degrees and 50% RH Cure rate About 3mm per 24 hours at 23 degrees and 50% RH Walk on / sand After about 12 hours / 24 hours Coverage About 600 to 1000 g per m2, depending on trowel and flooring type Density About 1.35 kg/l Shore A hardness About 38 after 28 days Shelf life 12 months from production, unopened and stored correctly Storage Dry, out of direct sunlight, 5 to 25 degrees Use Interior only SafetyIt contains small amounts (under 1 percent) of isocyanates, so avoid skin contact and breathing vapour, and keep the product away from heat, sparks and open flames. Work in a well-ventilated area and wear gloves and eye protection. If it gets on skin, remove contaminated clothing and wash with soap and plenty of water. For eye contact, rinse with water with the eyes held open and seek advice if irritation persists. Refer to the Safety Data Sheet (SDS) for full details.
$19.37
Soudal Genius Gun Gap Filling Expanding Foam is a one-handed, ready-to-use polyurethane foam for filling gaps, holes and joints while adding thermal and acoustic insulation, supplied here as a single 500ml can. The applicator trigger is built into the can, so there is no need to buy a separate foam gun, and the can can be put away part-used and picked up again on the next job.About the formulaA one-component, moisture-curing polyurethane foam with a stable, thixotropic body that stays where you put it. A built-in trigger and straw let you control the amount you dispense, and the resealable applicator keeps the can usable for up to 6 weeks after first use. Once cured it is light, sound-reducing and chemically inert, with minimal shrinkage and very little post-expansion. Manufacturer data lists a free-foamed density of about 25 kg/m³, sound insulation of 58 dB and thermal conductivity of 0.037 W/m.K. One 500ml can yields roughly 19 litres of free foam, or about 17 metres of joint fill. The foam is champagne in colour and is not UV resistant, so exposed foam needs a protective finish.Where to use itIndoors: filling gaps around door and window frames, sealing pipe and cable penetrations, closing holes and cavities in walls and ceilings, cutting down draughts and thermal bridges, and adding a sound-deadening layer.Outdoors: sealing gaps and openings in roof constructions and around frames and penetrations. Cover the cured foam with paint, plaster or sealant to protect it from UV light.Suitable materials include brick, concrete, masonry, timber, metals and most plastics, as well as most other common building materials. It does not bond to polyethylene (PE), polypropylene (PP) or PTFE. Run a quick adhesion test on unusual substrates first.How to use it Make sure surfaces are clean, dry and free of dust and grease, then lightly mist them with water to help the foam cure. Shake the can hard for at least 20 seconds, then open the cover and fold the tube out horizontally. Turn the can over and squeeze the trigger to dispense. Fill holes and cavities only about one third full, as the foam expands a lot as it cures. Shake the can again every so often while you work. For deep voids, build up in layers and moisten between each layer. When you finish, detach the bung, plug the nozzle with it, close the cap and store the can upright. Once fully cured, trim the foam with a sharp knife, then sand, paint, plaster or cover with sealant as needed. Important notesWipe off uncured foam straight away with Soudal Gun and Foam Cleaner or acetone, and test the cleaner on plastics, lacquer and paint first as they can be affected. Cured foam can only be removed mechanically or with a PU foam remover, and it must never be burned off. Use the product between roughly +5°C and +30°C. Skin forms in about 7 minutes and the foam can be cut after about 25 minutes (manufacturer figures, measured under standard test conditions, so real-world times vary with temperature, humidity and bead size). Cured foam is not UV resistant. Do not use it near electrical boxes or light fittings without checking the clearance guidance. Unopened cans keep for at least 12 months when stored upright in a cool, dry place at +5°C to +25°C.Specifications Brand Soudal Product Genius Gun Gap Filling Expanding Foam Manufacturer code 132272 Pack 1 x 500ml aerosol can Colour Champagne Base One-component polyurethane, moisture curing Application Built-in Genius Gun trigger applicator, one-handed Reusable Up to 6 weeks after first use Skin formation About 7 minutes Cutting time About 25 minutes Yield (500ml) About 19 L of free foam, about 17 m of joint fill Shrinkage after curing Under 3% Expansion after curing Under 1% Temperature resistance (cured) -40°C to +90°C, up to 120°C for a maximum of 1 hour Can size 65 x 65 x 315mm Use Interior and exterior (protect from UV) SafetyThis is a pressurised aerosol with flammable propellant and contains isocyanates. Keep it away from heat, sparks, flames and other ignition sources, do not smoke while using it, and never pierce or burn the can, even when empty. Wear gloves, safety glasses and protective clothing, and use only in well-ventilated areas. People already sensitised to isocyanates, or with asthma, eczema or skin problems, should avoid contact with the product. Refer to the Safety Data Sheet (SDS) for full details.
$16.20
Bostik Fill It Expanda Foam is a one-component, multipurpose polyurethane expanding foam for sealing, filling, bonding and insulating in a single step, supplied here in a 500ml aerosol can with a straw applicator. It expands to take up gaps and cavities of many sizes, then cures into an airtight, moisture-resistant seal that is designed not to shrink away from the surrounding surface.About the formulaA moisture-curing polyurethane foam that is ozone safe and has a mostly closed-cell structure, so it insulates against both heat and cold. Once cured it can be cut, sanded, plastered or painted to a neat finish. The included straw applicator lets you place foam into tight or awkward spots and apply it at any angle. The foam is not UV stable, so cured foam left exposed to sunlight should be painted.Where to use itIndoors: filling gaps and cavities around window and door frames, insulating around pipes, cutting down draughts, dust and noise, and adding a sound-absorbing layer or acoustic baffle.Outdoors: sealing openings in roof construction, filling larger holes and gaps in exterior walls, and helping to keep out insects and rodents (paint exposed cured foam).Suitable materials include concrete, brick, stone, plaster, timber and metal, as well as many plastics such as EPS, XPS, rigid PU foam and uPVC. It is not suitable for polyethylene (PE), polypropylene (PP), polycarbonate (PC), PMMA, PTFE, soft plastics, neoprene or bituminous surfaces.How to use itMake sure surfaces are clean, dry and free of dust, grease and loose material. Apply within the temperature range given on the can (+5°C to +35°C). Fit the straw applicator, shake the can well as directed on the label, and fill gaps only part-way, because the foam expands as it cures. Follow the label and Safety Data Sheet for cleaning up uncured foam. Once cured, trim any excess by cutting or sanding, then paint, plaster or finish as required.Important notesDo not use where the foam will sit under a permanent water load, or in cavities that are too dry to supply the moisture needed for curing. The foam is moisture-curing, so cure time varies with temperature, humidity and the surface. Typical values at 20°C and 60% relative humidity are a skin time of about 8 to 12 minutes and a cure of around 1 hour for a 30mm bead. Uncured foam can stick firmly to skin and clothing, so keep it off both while working.Specifications Brand Bostik Product Fill It Expanda Foam Multipurpose Polyurethane Expanding Foam Pack 500ml aerosol can with straw applicator Colour Off-white Base One-component, moisture-curing polyurethane foam Application Aerosol can with straw applicator Application temperature +5°C to +35°C Skin time About 8 to 12 minutes at 20°C and 60% RH Cure rate About 1 hour for a 30mm bead at 20°C and 60% RH Temperature resistance (cured) -40°C to +90°C continuous Use Interior and exterior SafetyUse in a well-ventilated area, keep away from heat, sparks and open flames, and do not pierce or burn the can, even when empty. Wear gloves, eye protection and protective clothing, and avoid breathing vapour or aerosol. If skin or hair is contaminated, remove affected clothing and flush with running water. Store in a well-ventilated place away from heat and dispose of the can through an approved waste facility. Refer to the Safety Data Sheet (SDS) for full details.
$13.47
Parfix Foam Fill Triple Expanding Filler is a polyurethane foam in a 750g aerosol can, made for packing out large gaps, cracks and cavities in and around the home. It expands well beyond its sprayed volume to fill irregular voids, then cures to a durable, water resistant foam that bonds to most common building surfaces.About the formulaA one-part polyurethane foam based on an isocyanate (MDI) prepolymer, supplied in a pressurised can. Once cured it is a firm, shrink resistant foam that can be cut, sanded and painted. Cured foam is not UV resistant, so exposed outdoor areas should be painted or covered.Where to use itIndoors: gaps around pipes and cable penetrations, cracks and holes in walls, and cavities around frames and fittings.Outdoors: holes and gaps in brickwork and other building surfaces, protected from direct sunlight once cured.Suitable for most building surfaces, including timber, metal, brick, stone and other masonry. Test on a small hidden area first if you are unsure about a particular material.How to use itWear gloves and safety glasses and work in a well ventilated area. Make sure surfaces are clean and free of loose material, dust and grease. Follow the directions printed on the can for shaking, nozzle attachment and application. Because this foam expands strongly, fill the gap only partly and allow room for growth rather than over-filling. Once fully cured, trim any excess with a knife or saw, then sand or paint as required. Uncured foam is best wiped off straight away with a suitable cleaner as directed on the can. Cured foam must be cut or sanded off.Important notesNot UV resistant, so paint or coat any foam that will be exposed to sunlight. Take care not to over-fill, as expanding foam can distort thin frames, door jambs and window casings. Keep the can away from heat, flames and sources of ignition. Check the can label for temperature range, cure times and further directions, as these are not covered in the product data we hold.Specifications Brand Parfix Product Foam Fill Triple Expanding Filler Pack 750g aerosol can Colour Off white / yellow Base Polyurethane (isocyanate-based) Application Aerosol can Finishing Can be cut, sanded and painted Shrink resistant Yes UV resistant No Use Interior and exterior SafetyUse only in well ventilated areas, wear gloves and eye protection, avoid breathing vapour and wash hands after use. People with asthma or sensitivity to isocyanates should take particular care. Do not puncture or burn the can, and keep it away from heat and ignition sources. Store upright in a cool, secure place away from children and check periodically for leaks. Refer to the Safety Data Sheet (SDS) for full details.
$19.76
Bostik Ultraset SF Pro is a ready-to-use, solvent-free polyurethane adhesive for fixing timber flooring, supplied here as a single 600ml sausage pack. It is an elastomeric, one-part formula made for fitting parquet, solid strip, engineered, bamboo and sheet timber flooring to flat concrete or timber subfloors, or over an existing floor.About the formulaA one-part, moisture-curing polyurethane with no solvent and a zero VOC rating. There is no mixing, and it spreads easily. It stays flexible after full cure, so the bond can move with the timber, and it is suitable over radiant heating. Bostik also lists good acoustic properties, and the product is made in Australia. The technical data sheet notes testing to ASTM C794 for peel adhesion on a range of Australian hardwoods. It also notes that the product meets EN 14293:2006 for adhesives bonding parquet to a subfloor. Bostik quotes a Shore A hardness of about 52 and a timber-to-timber shear strength of 1.4 N/mm2 (2mm bond line, BS EN 14293).Where to use itIndoors: direct-stick installation of timber floors over flat concrete or timber subfloors, or over existing floors, in residential and commercial settings. It can also fix recommended acoustic underlays as an intermediate layer between the subfloor and the flooring.Outdoors: not intended for exterior use.Suitable flooring types include parquet, solid strip, engineered, bamboo and sheet timber systems.How to use itSurfaces must be clean, dry, sound and free of voids, curing compounds, loose material, oil and grease. The subfloor should be flat to within 3mm over a 3m straightedge. If it is out of tolerance, prime and level it first using Bostik's recommended primer and levelling compound, and follow their data sheets. Spread the adhesive evenly so the film is not patchy and has no pinholes. The data sheet calls for a wet film thickness above 300 microns. Lay the flooring in line with the timber manufacturer's installation instructions. Where a vapour barrier is needed over a new or green slab, Bostik's Ultraseal Vapour Barrier is the recommended option.Important notesThe adhesive needs atmospheric moisture to cure. In low humidity (below 40%), check with Bostik technical services before you start. Do not use it as a waterproofing membrane. Do not install it over wet, contaminated or friable surfaces, and keep it away from water exposure. Allow timber to acclimatise and leave expansion gaps as the timber manufacturer or installation standard requires. Dense, burnished concrete may need abrading first. Cure and walk-on times depend on temperature, humidity and film thickness, so check the current data sheet for your job. A sausage gun is needed to dispense the 600ml foil pack, and it is not included.Specifications Brand Bostik Product Ultraset SF Pro Solvent Free Polyurethane Timber Flooring Adhesive Pack 1 x 600ml sausage Base One-part, solvent-free, moisture-curing polyurethane (elastomeric) VOC Zero VOC Application Sausage gun, spread with a notched trowel Shore A hardness Approx. 52 Shear strength (timber to timber, 2mm) 1.4 N/mm2 (BS EN 14293) Standards Tested to ASTM C794; meets EN 14293:2006 Use Interior timber flooring, including over radiant heating Origin Made in Australia SafetyBostik describes it as solvent-free and non-flammable. Wear chemical-resistant gloves and eye protection, work with good ventilation, and avoid skin contact and breathing vapour. Store in the original sealed container, under cover, dry and within the manufacturer's temperature range. Refer to the Safety Data Sheet (SDS) for full details.
$15.67
Selleys Aquadhere Durabond is a solvent-free, moisture-curing polyurethane wood glue for jobs that need more durability than a standard PVA can offer, supplied here in a 250ml bottle. It bonds timber to a wide range of other materials, copes with moisture and heat, and can be sanded, painted or stained once cured.About the formulaUnlike water-based PVA glues, Durabond cures by reacting with moisture in the air and the substrate. It gives a strong, water-resistant bond (not intended for permanent immersion) and is heat resistant up to about 140°C. The glue expands slightly as it cures, which helps it fill small gaps in imperfect joints. It also sands without clogging sandpaper or timber the way PVA glues can. Selleys notes it resists acids and most chemicals, unlike PVA-based glues.Where to use itIndoors: furniture making and repairs, timber joinery, cabinet repairs, sauna or other high-heat and high-moisture areas, repairing wooden tool handles, and general workshop fixes.Outdoors: planter boxes, steps off a veranda, window repairs, attaching a timber letterbox to a metal support frame, cubby or kennel repairs, and boat oar or interior panel repairs.Suitable materials include all timbers, MDF, metal, glass, concrete, masonry, ceramics and most plastics. It is not for polyethylene or polypropylene, and you should test other plastics first.How to use itSurfaces should fit closely and be clean, dry of dust and free of grease. At least one surface should be porous, as the glue needs moisture to cure. On very dry porous surfaces, wipe with a damp cloth for about a minute before bonding. Wear gloves, because the adhesive bonds to skin. Apply to the joint, bring the parts together within the working time and clamp them while the glue cures. Once cured, the joint can be sanded, and the surface can be painted or stained after sanding.Important notesWorking time is about 10 minutes, depending on temperature and humidity. Allow around 4 hours of clamp time. Full cure takes up to 24 hours, depending on humidity and how porous the material is. Do not apply below 5°C. Use may be restricted in very dry conditions because the glue needs atmospheric moisture to cure. It is not recommended for structural applications. The bond is waterproof but not for permanent water immersion.Specifications Brand Selleys Product Aquadhere Durabond Polyurethane Wood Glue Pack 250ml bottle Colour Amber, dries to a yellow opaque finish Base Solvent-free, moisture-curing polyurethane Application Bottle, applied by hand Working time About 10 minutes Clamp time About 4 hours Full cure Up to 24 hours Minimum application temperature Above 5°C Heat resistance Up to 140°C Use Interior and exterior SafetyUse with adequate ventilation. Store in a well-ventilated place with the container tightly closed and locked up. Refer to the Safety Data Sheet (SDS) for full details.
$19.76
![Selleys Flexiseal FC Polyurethane Sealant & Adhesive 600ml Sausage [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-flexiseal-fc-polyurethane-sealant-adhesive-600ml-sausage-white-2.png?v=1792410682&width=645)
Selleys Flexiseal FC is a fast-curing polyurethane sealant and adhesive in white, supplied here as a 600ml sausage for sealing and bonding jobs around the building site or the house. It does two jobs in one product: it seals joints between common building materials and bonds them, and it stays flexible enough to cope with the movement those joints see through the seasons.About the formulaA single-component polyurethane with a non-slumping body, so it stays put in vertical joints instead of sagging. It is designed to grip common building surfaces without a primer, cures to a waterproof, flexible seal and can be painted once cured. Selleys rates it for joint movement of around plus or minus 25%.Where to use itIndoors: joints between wall and ceiling elements, around door and window frames, and acoustic rated walls, plus general bonding of building materials.Outdoors: weatherproofing joints between brickwork, masonry, concrete, timber or metal frames, sealing around roofing, retaining walls, external wall and cladding joints, and expansion joints.Suitable materials include concrete, brick, masonry, ceramic tile, metals, softwood and hardwood, plus some plastics (test other plastics and rubber first).How to use itMake sure the joint is clean, dry and free of dust, oil and other contaminants, and use a backing rod in deeper joints. Cut the end of the sausage, load it into a sausage-style applicator gun and extrude the sealant so it makes full contact with both sides of the joint, avoiding trapped air. Tool the surface smooth with a spatula before a skin forms. Once cured, it can be painted. For outdoor work, a suitable exterior paint will help the finish last longer.Important notesWill not adhere to polyethylene (PE), polypropylene (PP) or PTFE. Do not apply when the air or surface temperature is below 5°C. Not suitable for permanent water immersion or below water line use. Not intended for structural applications or general glazing. Avoid alcohol and solvent cleaners on the sealant while it cures, as they can interfere with the cure. Very damp substrates can cause bubbling in the sealant. It may affect the drying of oil or alkyd based paints, so test paint compatibility first. White sealant can yellow slightly with age and sun exposure. Store unopened sausages below 30°C in a cool, dry place out of direct sunlight, where they keep for around 12 months from manufacture. Opened sausages may skin over near the opening, so discard any lump or skin before using the rest.Specifications Brand Selleys Product Flexiseal FC Polyurethane Sealant & Adhesive Size 600ml sausage Colour White Base Polyurethane (single component) Application Sausage, via sausage gun Joint movement capability Plus or minus 25% Minimum application temperature 5°C Shelf life (unopened) About 12 months below 30°C Use Interior and exterior SafetyPolyurethane products can still irritate the skin, eyes and airways, so wear gloves and safety glasses, work with good ventilation and avoid prolonged skin contact. Store in a cool, dry, well-ventilated place away from heat, ignition sources and food, upright and tightly closed. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$32.06
Crommelin One Coat Rapid is a heavy-duty, liquid-applied waterproofing membrane that goes down before tiling, supplied here in a 1L pail for showers, laundries and other small wet-area jobs. It is a polyurethane-modified grey membrane that cures into a seamless, flexible layer under tile, so there are no laps or joins in the finished surface.About the formulaThe membrane is polyurethane modified for high flexibility and reinforced for strength and durability. Crommelin states it stretches by more than 300% and stays flexible over time, which helps it cope with minor substrate movement. It dries to a keyed, slightly textured surface that gives cement-based tile adhesive something to grip. It is made to be used with cement-based tile adhesives that comply with AS 2358, and it is designed to meet AS 4858 and AS 3740. It is water based, so tools clean up with water.Where to use itIndoors: showers, bathrooms, laundries and kitchens, on both walls and floors, before tiling.Outdoors: balconies, patios and podiums under tile, where the membrane is covered by the tile finish.Suitable substrates include concrete, cement render and screeds, plasterboard and wet-area plasterboard, suitably prepared compressed fibre cement sheet, timber, plywood, wet-area particleboard and steel.How to use itSurfaces need to be sound, clean and dry, with loose or crumbling material removed first. New concrete should have cured for at least 28 days before coating. Where the manufacturer's data sheet calls for a surface primer, use a 1:1 dilution of the membrane with water and let it dry. On walls, one coat is enough, and Crommelin quotes coverage of up to 2m² per litre. Floors need more material per square metre, and complex or irregular surfaces may need extra coats, so check the technical data sheet for your job. Allow good airflow while it cures. Once the membrane has cured, a flood test is described in the manufacturer's data sheet: water about 25mm deep for 2 hours, removed straight afterwards. Clean tools with water before the membrane dries. Uncured material can be removed with warm water and detergent.Important notesThis membrane is not designed to go directly onto white-set plaster. Prime that surface first with a coat of Crommelin Next Day New Concrete Sealer and let it dry. Full cure takes about 7 days. Re-coat and cure times get longer in cold, humid or still conditions. Tile over the membrane so it is not left exposed. Waterproofing wet areas is regulated work in many parts of Australia, so check local requirements and follow the manufacturer's full instructions.Specifications Brand Crommelin Product One Coat Rapid Under-tile Waterproofing Membrane Pack 1L pail Colour Grey Base Polyurethane-modified, liquid applied, water clean up Elongation Over 300% Coverage Up to 2m² per litre (see data sheet for floors and irregular surfaces) Full cure About 7 days Standards Designed to comply with AS 4858 and AS 3740 Use Interior and exterior under-tile applications SafetyUse it with good general ventilation, avoid prolonged skin and eye contact, and wash your hands after use. Store the pail sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$36.48
Dunlop FC Joint Sealant Dunlop FC Joint Sealant is a premium, ultra flexible, moisture curing polyurethane sealant designed for jointing fibre cement, blueboard and compressed fibre cement sheets. The non slump formula handles joints up to 40 mm wide with a movement capability of plus or minus 25 percent. It is easy to apply, solvent free and isocyanate free. Colour: Grey. Why choose this sealant High flexibility for dynamic joints Non slump for clean, accurate beads on vertical and horizontal surfaces Solvent free and isocyanate free Paintable after curing Reliable performance supported by a 10 year guarantee Ideal uses Joints in fibre cement, blueboard and compressed fibre cement sheets Facade and cladding joints where movement is expected General building joints up to 40 mm width Compatible surfaces Adheres to most common construction substrates, including: Fibre cement sheets and blueboard Precast concrete panels, blockwork and bricks Sandstone and granite Fibreglass Plasterboard Technical details Movement capability ± 25% Joint width Up to 40 mm Skin time Approximately 35 minutes at 23°C and 50% RH Tack free time Approximately 1 hour at 23°C and 50% RH Cure rate About 2.5 mm per 24 hours at 23°C and 50% RH Application temperature 10°C to 35°C Clean up Warm water immediately after use Shelf life 12 months unopened, stored cool and dry Finish Paintable when dry. Can be overcoated with paint or texture coats. Colour Grey Surface preparation Ensure surfaces are clean and dry, free of dust, oil, grease, salt, mould, release agents and any contaminants that may affect adhesion. Mask adjacent areas to keep lines neat. Follow sheet fixing instructions from the board manufacturer. How to apply Cut the nozzle at a sharp angle slightly wider than the desired bead or joint width. Use a suitable backing rod where required to control depth. Aim for a joint depth equal to half the joint width. Gun the sealant into the joint and tool within 10 minutes using a round spatula to ensure full contact with the joint sides. Curing times increase in cold or humid conditions. Safety and handling Avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection. Ensure adequate ventilation during application. Keep out of reach of children. Refer to the product SDS for full safety guidance. Guarantee Backed by a 10 year guarantee when used as directed.
$21.58
SikaBond High-Strength Foam Construction Adhesive 750 mL is a reliable one component foam construction adhesive dispensed from a can chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 750 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Sika High-Strength for your next project Everyday jobs often involve mixed materials and imperfect surfaces. SikaBond High-Strength Foam Construction Adhesive 750 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Fixing studs, battens, and sheets Filling small gaps while bonding Fast installation where speed saves labour Suitable surfaces The adhesive works well on the following surface types when properly prepared: Timber and masonry Concrete and fibre cement Many building materials except PE and PP Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of assemble parts within the open time to ensure a strong bond. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Expands slightly to fill gaps, then cures to a firm, high strength foam. Provides excellent initial grab and reduces the need for nails in many applications. Temperature and environmental performance Apply within the can's specified temperature range. Humidity supports foam curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured foam with the prescribed cleaner. Once cured, cut back mechanically. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store cans upright. Do not expose to heat. Observe transport and disposal rules for pressurised containers. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$31.50
![Sika Sikaflex Pro+ Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$24.00
Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance. Incredible bond strength Waterproof Superior strength Adheres to even visibly damp surfaces Fast curing - less than 30 minutes Materials: wood, ceramic, stone, concrete, metal, glass, fibreglass, leather, laminate, masonry, plasterboard and some plastics.
$25.98
Tarzans Grip Mega Bond Glue is suitable for bonding large variety of surfacees in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resitance. Incredible bond strength Waterproof Adheres to even visibly damp surfaces Fast curing - less than 30 minutes
$10.50
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black] (2)](http://gluesaustralia.com.au/cdn/shop/files/sikaflex-sika-227-automotive-sealant-fast-curing-non-sagging-310ml-black-2.jpg?v=1792406662&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$27.48
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895456164_5c293f0a-df90-415e-875b-0ed963018cfa.jpg?v=1754711706&width=645)
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/sika-sikaflex-252-high-strength-structural-adhesive-sealant-white-2.jpg?v=1792406508&width=645)
High strength, structural grade polyurethane adhesive sealant High strength elastic adhesive, suitable for structural joints subjected to high dynamic stress Suitable for use on trucks, trailers and caravans with excellent adhesion to timber, metals, primers and paint coatings Vibration dampening USE Sikaflex® 252 is suitable for structural joints that will be subjected to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminium (incl. anodized components), sheet steel (incl. phosphated, chromated and zinc-plated components), metal primers and paint coatings (2-c systems), ceramic materials and plastics. CHARACTERISTICS AND ADVANTAGES 1-C formulation Elastic Can be overpainted Good gap-filling properties Capable of withstanding high dynamic stresses Vibration Damping Non-corrosive Electrically non-conductive Bonds well to a wide variety of substrates
$53.62
You have seen 48 out of 70 products
High‑strength, flexible adhesives and sealants with excellent durability and water resistance. Suitable for many substrates. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
