Low Shine

Dunlop Ready-to-Go Coloured Grout is a premium, pre-mixed grout for fast, clean results on walls and floors. No mixing, no mess, just open, apply, and buff for a smooth, long-lasting finish. The formula includes Grout Shield for anti-mould and anti-bacterial protection to help surfaces stay cleaner for longer. Suitable for interior and exterior applications, and available in a wide colour range to match or contrast your tiles. Ready-mixed convenience, apply straight from the tub Contains Grout Shield for mould and bacteria resistance Use on walls & floors, indoors & outdoors* Ideal for joint widths from 1–5 mm Great for rejuvenating old grout (min. removal depth: 1 mm walls, 2 mm floors) *Always follow the data sheet guidance for your specific area and exposure. Where to Use Ceramic, porcelain and most glazed tiles Bathrooms, kitchens, splashbacks, laundries, living areas Light-duty exterior tiled areas (check exposure & substrate) This grout is designed for typical domestic and light commercial tiling where a smooth, uniform finish is desired. Colours & Finish Available in a contemporary colour palette (e.g. whites and greys) to complement most tile styles. Use Dunlop’s colour selector to visualise combinations before you start. Coverage Coverage varies by tile size, joint width and depth. As a guide (per kg) of grout: Tile size (L×W×Thickness) Joint width 1.5 mm Joint width 3 mm Joint width 5 mm 25×25×4 mm mosaics ≈1.04 m²/kg ≈0.52 m²/kg ≈0.31 m²/kg 100×100×8 mm ≈2.08 m²/kg ≈1.04 m²/kg ≈0.63 m²/kg 200×200×8 mm ≈4.17 m²/kg ≈2.08 m²/kg ≈1.25 m²/kg Tip: Allow an extra 10–15% for wastage due to technique, tile type and site conditions. Directions (Summary) Prep: Ensure joints are clean, dry, and free from dust, adhesive residue and contaminants. For rejuvenation, remove at least 1 mm (walls) or 2 mm (floors) of old grout. Apply: Using a rubber grout float, force grout firmly into joints at a 45° angle. Strike & shape: Allow grout to firm in the joint (~15 mins). Shape joints as required. Clean: Wipe diagonally with a dense, damp sponge, rinsing frequently. Use minimal water to reduce shade variation and shrinkage. Buff: When touch-dry (typically 6–24 hrs), buff tile faces with a clean, dry cloth. Drying & Use Initial set at ~24 hrs at 23 °C / 50% RH Shower walls can be exposed to water after ~24 hrs Clean-Up & Storage Clean tools and residue with water while the grout is still wet. Reseal the tub between uses to prevent skinning. Store upright in a cool, dry place. Safety Read the Safety Data Sheet before use and follow PPE guidance. Avoid contact with eyes and prolonged skin contact. Keep out of reach of children.

Read more less

Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.  Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C.  Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.

Read more less

Get sharp, clean paint edges with Paint Partner Thick Masking Tape. This reliable painter’s tape is designed to stick firmly, remove cleanly within the recommended time, and resist paint bleed for professional looking results on walls, ceilings, trims, doors, and furniture. Crisp paint lines with reduced bleed on properly prepared surfaces Thicker construction for easy handling, straight tearing, and consistent edging Clean removal within the recommended timeframe to help reduce residue Suitable for most interior paint systems including acrylic and enamel Value 6 pack for multi room or multi day projects Ideal For Masking skirting boards, window frames, architraves, and cornices Two tone feature walls and colour blocking Furniture upcycling and detailed trim work Protecting hardware and fixtures during repainting Specifications Brand Paint Partner Product Thick Masking Tape for Crisp Paint Lines Width 24 mm Length per roll 27 m Pack size 6 rolls Adhesive type Pressure sensitive Surface types Painted drywall, timber trim, metal, glass, and sealed surfaces Use Interior masking and edge definition Removal window Remove within the recommended project timeframe for clean results Colour Neutral masking tape How to Use Prep the surface Ensure it is clean, dry, and free of dust or grease. Lightly sand and wipe where needed. Apply the tape Align to the paint edge and press down firmly, smoothing along the full length to seal the edge. Paint Apply paint in light coats, brushing or rolling away from the tape edge to reduce bleed. Remove While paint is still slightly tacky or once fully dry per paint instructions, peel the tape back on itself at a 45 degree angle. Pro Tips Burnish the tape edge with a clean cloth or plastic card for the sharpest lines. For textured walls, apply a very light coat of the base colour along the tape edge, let it set, then apply the top colour. Test in a small, hidden area on delicate or freshly painted surfaces. What’s in the Pack 6 rolls of Paint Partner Thick Masking Tape, each 24 mm x 27 m. Storage and Safety Store in a cool, dry place away from direct sunlight. Use on fully cured paint only. Always test before full application. Dispose of used tape in household waste according to local guidelines. Frequently Asked Questions Will it pull off existing paintWhen applied to properly cured paint and removed within the recommended timeframe, it is designed for clean removal. Always test on a small area first. Can I use it outdoorsBest suited for interior projects. For extended outdoor exposure consider a UV resistant painter’s tape. How do I get the sharpest edgePress the tape down firmly along the edge and remove at a 45 degree angle while paint is slightly tacky or fully cured as directed by the paint manufacturer. Why Buy From Glues Australia Australian based support and fast dispatch Carefully curated paint preparation range Competitive pricing on multi pack project essentials

Read more less

DESCRIPTION SikaSeal® Acrylic 100 is a flexible, one component, water based acrylic joint sealant and gap filler where low demand of elongation are required, for interior use. USES SikaSeal® Acrylic 100 is suitable for sealing low movement joints around: ? brick ? Concrete ? Plasterboard ? Windows ? Doors ? Ceramic tiles SikaSeal® Acrylic 100 fills cracks and adheres to: ? Glass ? Wood ? Aluminium ? Brick ? Concrete ? Plasterboard ? Ceramic ? Painted surfaces. CHARACTERISTICS / ADVANTAGES Excellent adhesion to most common construction materials. Water clean-up of uncured sealant. Can be sanded back once fully cured if required to give smooth surface finish. Can be painted over using water based paints. Non-toxic

Read more less

Selleys Brick and Concrete Silicone is a neutral (non-corrosive) cure 100% silicone sealant. It is low modulus or can be stretched easily, which makes it ideal for joints which will move significantly such as expansion joints in concrete, and is grey so it will blend in with the concrete surrounds. Features Superior flexibility +/- 25% movement capability & up to 500% elongation or stretch. Superior silicone formulation forms a durable seal which locks out water and which does not shrink when drying. UV and weather resistant – Immune to the damaging effects of the sun. Temperature resistance – approximately -60°C +150°C. Superior adhesion to concrete and fibre cement surfaces. Low odour so can be used in any environment without discomfort. 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Grey Appearance Smooth Where can this product be used? joints in brick walls expansion joints in concrete Perfect for use on or around: Walls Patios Floors Fencing Windows Expansion joints in concrete. Can not be painted over. Not suitable for use in below waterline applications. Do not use in below ground applications. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Bricks and mortar Ceramics and porcelain Concrete Fibre cement Marble & stone Metal Wood Many plastics including polystyrene How to use this product Throughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow to dry completely before applying silicone. If there old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenous product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course grain, as the silicone will adhere more readily to a scratched up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipes. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see a handy tip. The sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. Handy tips Tips for Using a Brick & Concrete Silicone Sealant Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safetytips Uncured product may irritate eyes. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use keep the nozzle on the cartridge Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.

Read more less

Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS  Initial set 5 minutes. Curing set 15-30 minutes.  Compressive strength of 2,000psi or greater in 24 hours  Maximum strength in 28 days  Non-toxic  Volume change: Expansion after 24 hours 0.1%  Contraction after 28 days 0.01%  Water absorption 1.7% after 14 days  Factory Production to BS 5750 Part II BONDS TO:  CEMENT  TIMBER  MASONRY  FIBREGLASS  STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.

Read more less

Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS  Initial set 5 minutes. Curing set 15-30 minutes.  Compressive strength of 2,000psi or greater in 24 hours  Maximum strength in 28 days  Non-toxic  Volume change: Expansion after 24 hours 0.1%  Contraction after 28 days 0.01%  Water absorption 1.7% after 14 days  Factory Production to BS 5750 Part II BONDS TO:  CEMENT  TIMBER  MASONRY  FIBREGLASS  STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.

Read more less

Crommelin Pond Sealer Clear is a water-based, clear waterproofing membrane for sealing above-ground ponds, bird baths and ornamental water features, supplied here in a 1L pail. It goes on as a seamless coating and dries to a clear, low-sheen finish, so the look of the concrete, render or brickwork underneath is kept. It is designed to stay watertight under permanently wet conditions on structures that don't move.About the formulaA ready-to-use, water-based membrane that is non-toxic and safe for fish and plants. The manufacturer's technical data sheet also lists it as suitable for collecting or storing drinking water. It is UV stable, dries quickly and has excellent adhesion to porous cement-based surfaces. Repairs are easy, and tools wash up with water. It dries clear and hard, so it is meant for solid structures without joins, internal corners or expected movement. Where there are existing holes or cracks, or movement is expected, Crommelin recommends its Pond Sealer Colours membrane instead.Where to use itIndoors: ornamental water features, indoor fountains and other solid, porous water-holding features that won't flex.Outdoors: new or renovated above-ground fish ponds, bird baths, and ornamental water features built from concrete, render, brick or block.Suitable surfaces include concrete, cement render, brickwork, concrete blocks and other cementitious substrates. It is not suitable for non-porous surfaces.How to use itSurfaces must be clean, sound and completely dry, and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and laitance. Repair any loose or crumbly areas first with a suitable repair mortar. To check porosity, wet a small area. If it darkens, the surface is porous and can be sealed. If it doesn't, it is too dense to seal. Stir the sealer well before use and apply with a brush or roller. Apply when surface and air temperatures are between 10 and 35°C and humidity stays at or below 85%. First coat: mix equal parts sealer and water, then apply a thin, even coat. Allow about 15 minutes to dry. Second coat: apply un-thinned sealer over the surface and let it dry. Third coat: apply un-thinned sealer at right angles (90 degrees) to the first coat. Wash brushes and rollers in water before the sealer dries. Important notesRecoat after about 4 hours. Full cure takes about 7 days, and good airflow helps. Keep the coating away from moisture until it has fully cured, and protect it from damage before filling with water. Not suitable for use in chlorinated water. Do not apply it to non-porous surfaces. It is not intended for in-ground ponds or for structures with cracks or movement. Don't apply in extreme heat, cold or humidity. Coverage depends on how porous the surface is. As a guide, 1L produces about 2 to 4 square metres of finished coating.Specifications Brand Crommelin Product Pond Sealer Clear Pack 1L pail Colour Clear when dry, low-sheen finish Base Water-based membrane Application Brush or roller Recoat time About 4 hours Full cure About 7 days Coverage About 2 to 4 m² of finished coating per 1L, depending on surface porosity Application conditions 10 to 35°C, maximum 85% humidity Clean up Water, before the product dries Use Interior and exterior, fish ponds and ornamental water features SafetyStore in a cool, dry place. Follow normal good practice when handling: avoid contact with eyes and skin, wash hands after use, and keep out of reach of children. Crommelin supplies it on request. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Selleys Wet Area Matt White: The Lasting Choice for Wet Areas Key Features Matt finish for elegant look 100% silicone sealant 25-year guarantee against cracking or peeling Waterproof seal with superior adhesion Mould-resistant formula Non-corrosive, neutral cure Best For Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures. Suitable Materials Ceramic, Glazed & Porcelain Fixtures Metal, Copper & Brass Fittings Plastic Laminates Rubber Glass Stainless Steel Concrete & Grouts Many Plastics including Polystyrene How to Use Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application. Limitations Not paintable Not suitable for certain materials and uses Handy Tips Mask sides for neater joints. Work in manageable sections for a smoother finish. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping. Additional Info Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.

Read more less

Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS  Initial set 5 minutes. Curing set 15-30 minutes.  Compressive strength of 2,000psi or greater in 24 hours  Maximum strength in 28 days  Non-toxic  Volume change: Expansion after 24 hours 0.1%  Contraction after 28 days 0.01%  Water absorption 1.7% after 14 days  Factory Production to BS 5750 Part II BONDS TO:  CEMENT  TIMBER  MASONRY  FIBREGLASS  STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.

Read more less

A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. SafetyAvoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. SafetyAvoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

The Cyclone Fibreglass Flyscreen is a traditional, flexible insect screen mesh for replacing or fitting flyscreens on windows and doors, supplied here as a 910mm wide x 2m long roll. It suits everyday home use and is easy to cut to size and fit into a standard screen frame.About the productThis is a woven fibreglass flyscreen mesh with a matte charcoal protective coating. The dark finish helps cut sun glare and the coating has low heat transfer. The fabric is supple and pliable, so it is easy to handle and holds firm tension once it is fitted. Cyclone says it will not dent, corrode or stain, and it is UV stabilised for a longer working life. Cyclone rates its insect protection at 2 out of 3 on its own scale.Where to use itIndoors: window and door screens in bedrooms, living areas, kitchens and laundries, to allow fresh air while keeping flying insects out.Outdoors: screens on external doors, sliding doors and windows, where the UV stabilised mesh is built to cope with sun exposure.How to use it Measure your screen frame and cut the mesh a little larger than the frame opening. Lay the mesh over the frame groove and press it in with spline, using a spline roller (not included). Pull the mesh evenly as you work around the frame so it stays tight and flat. Trim off the excess mesh neatly along the spline once fitted. The flexible, pliable weave makes it quick to spline in and it resists kinking and denting. Important notesThis pack contains the mesh only. Spline, frames and tools are not included. Fibreglass mesh is a general-purpose flyscreen and is not a security screen or a pet-proof mesh. If you need extra protection against very small insects such as midges or sandflies, look at a finer weave screening. Wear gloves when cutting and handling if you have sensitive skin.Specifications Brand Cyclone Product Fibreglass Flyscreen Size 910mm wide x 2m long (1 roll) Material Fibreglass Colour Charcoal Finish Matte Insect protection rating 2 out of 3 (manufacturer scale) UV performance UV stabilised Hardware included No Use Window and door flyscreens, indoor and outdoor Care and storageKeep the roll flat or loosely rolled in a dry place and avoid sharp creases. Once fitted, clean the screen gently with a soft brush or cloth and mild soapy water, then rinse. Avoid scraping or pulling hard on the mesh so it keeps its tension and shape.

Read more less

Feast Watson Outdoor Furniture Oil in Clear is a penetrating timber oil made to protect outdoor furniture while keeping the natural look of the wood, supplied here in a 1L can. It soaks into the surface rather than sitting on top, so it leaves a natural matt finish that lets the grain and texture show through.About the formulaAn oil-based, one-component formula enriched with eucalyptus oil. It is designed to resist mould and to give excellent water resistance, and the film is penetrating, so it is not expected to crack or flake. The Clear colour keeps the timber's own tone. It is not recommended for direct sunlight or extreme conditions. If you want a higher level of UV protection, choose one of the tinted colours in the range (Hardwood, Jarrah, Teak or Weathered Grey).Where to use itIndoors: not the intended use, as this oil is made for outdoor timber.Outdoors: timber outdoor furniture such as chairs, tables and benches, plus timber BBQ trolleys.Suitable for exterior timber furniture. Test a small, hidden area first if you are unsure how your timber will look.How to use itClean the furniture first with Feast Watson Woodclean to remove dirt, oil, wax and grease, then let it dry fully. Stir the oil thoroughly before and during use so the colour stays even. If you need more than one can, combine them in a larger container first. Apply the first coat with a quality brush, working in sections along the grain and fully coating edges and end grain. A roller or applicator pad can also be used. Let the oil soak in, then wipe off any excess with a brush or clean cloth. Leave it for 12 hours before applying a second coat. For chairs and benches, start on the inside of the legs, then move up to the seat and finish with the back. Clean brushes and tools with mineral turpentine.Important notesAllow about 12 hours between coats. Touch dry time is around 6 hours at 25°C and 50% humidity, and cooler or more humid conditions will take longer. Do not apply below 10°C, in very hot weather, or when rain or heavy dew is expected while the coating dries. Two coats are recommended, and the manufacturer lists a spread rate of about 6m² per litre, which varies with the timber. Over time, watch for colour loss, dryness and weathering. When that happens, clean with Woodclean and apply one maintenance coat. Soak used rags and cloths in water before disposing of them.Specifications Brand Feast Watson Product Outdoor Furniture Oil Size 1L Colour Clear Base Oil-based, with eucalyptus oil Finish Matt Application Brush, roller or applicator pad Coats 2 Recoat time 12 hours Spread rate About 6m² per litre Minimum application temperature 10°C Clean up Mineral turpentine Use Exterior timber furniture, BBQ trolleys and benches SafetyUse in a well-ventilated area and keep away from heat, sparks and open flame. Avoid contact with skin and eyes, and wear gloves and safety glasses while working. Keep out of reach of children and store the sealed can in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Mont Marte Deco Pudge Matte is a 3-in-1 water-based decoupage glue, art sealer and matte varnish, supplied in a 300ml bottle for craft projects. You can stick your paper down, seal the surface and finish the piece with one product, so there is no need to swap between bottles mid-project.About the formulaA water-based, non-toxic formula with a milky appearance in the bottle. It dries clear to a soft matte finish that resists yellowing. The finish can be lightly sanded between coats for a smoother result, and brushes and tools wash out with soap and water while the product is still wet.Where to use itIndoors: decoupage, scrapbooking, school projects, paper crafts and sealing finished artwork or painted pieces.Outdoors: not recommended. This product is intended for indoor use only.Suitable for gluing paper to a surface and for sealing over acrylic paint, stains, wood, fabric and decoupage projects.How to use itBrush a thin layer of Deco Pudge onto the surface, lay your paper over it and smooth out any bubbles. Once the paper is down, brush 2 to 3 coats over the top as a sealer and varnish, letting each coat dry before applying the next. A light sand between coats leaves an extra-smooth surface. Wash tools with soap and water while the product is still wet. Reseal the bottle after use.Important notesThe product is touch dry in around 30 minutes and fully dry in about 24 hours. Store the bottle sealed in a cool place between 5 and 30 degrees C, away from direct sunlight. It is not intended for outdoor use. Always test on an offcut or a hidden spot first if you are working over a special finish.Specifications Brand Mont Marte Product Deco Pudge Decoupage Glue and Sealer, Matte Model number MMBB1210 Size 300ml bottle Appearance Milky liquid, dries clear Finish Soft matte Base Water-based Application Brush Touch dry Around 30 minutes Fully dry About 24 hours Clean up Soap and water while wet Storage temperature 5 to 30 degrees C Pack dimensions 54 x 54 x 169 mm Use Indoor only SafetyIt is a water-based craft product, but it is not designed to be eaten, so keep it away from food and drink and out of reach of young children. Children should be supervised when using it. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Crommelin DiamondTough Stone Shield Clear Sealer is a premium waterborne sealer made for dense natural stone, supplied here in a 1L pack that suits benchtops, feature walls and smaller floor areas. It protects against stains and water, dries clear, and leaves a natural to low sheen finish. Crommelin previously sold it as DiamondCoat Stone Shield. The brand says only the name has changed, not the product.About the formulaA water-based sealer that both penetrates the surface and forms a thin protective film, while still letting the stone breathe. It resists staining and abrasion and repels water well. It also contains an anti-microbial additive that helps stop mould and algae growing on the sealed surface. It is low odour and low VOC, dries quickly, and can be recoated soon after the first coat. It can be applied to vertical and horizontal surfaces.Where to use itIndoors: dense stone floor and wall tiles, stone and concrete benchtops, kitchens and living areas, and polished concrete.Outdoors: natural stone cladding and other exterior dense stone surfaces that suit a clear, low sheen protective coat.Suitable surfaces include granite, marble, bluestone, travertine, porcelain, polished concrete, terracotta, reconstituted stone and natural quarry stone. Always test a small patch first to check the colour enhancement, finish and slip resistance.How to use itThe surface must be clean and fully dry before you start. Crommelin requires a moisture test every time. If the surface has been acid etched, neutralise and rinse it thoroughly first. Apply the first coat evenly with a clean, lint-free tool so the surface is wet but no white excess liquid is left standing. Suitable tools are a brush, a roller, a lambswool applicator, a lint-free cloth or an airless sprayer. Apply the second coat in the same way once the first is touch dry, and within 2 hours. On very dense surfaces such as polished marble, the sealer may only need to be wiped on. If streaky film builds up on a dense surface once dry, wash it with warm soapy water, rinse and buff with a soft cloth. Clean tools with warm water and a little detergent straight after use.Important notesDo not apply when it is too hot or cold, when humidity is high, or when rain is expected within 48 hours. Allow about 24 hours before light foot traffic. Full cure takes around 7 days. Over-applying can leave a visible film on very dense stone, so work thinly and use a test patch to confirm the right rate. This product is a clear sealer. It cannot be tinted.Specifications Brand Crommelin Product DiamondTough Stone Shield Clear Sealer Pack 1L pail Colour Clear when dry Base Waterborne Finish Natural to low sheen Application Brush, roller, lambswool applicator, lint-free cloth or airless spray Recoat As soon as the first coat is touch dry, within 2 hours Light foot traffic About 24 hours Full cure About 7 days Application temperature 5 to 35°C Coverage Roughly 10 to 30 m² per litre, depending on how dense the surface is Primer required No Tintable No Use Interior and exterior SafetyEven so, avoid contact with skin and eyes, avoid breathing spray mist, and wear suitable protective clothing, gloves and eye protection when spraying. Keep the container sealed and store it in a cool, dry place. Keep it out of reach of children, and do not let it enter drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.

Read more less

Get crisp, professional paint lines with Wagner Mask-It. This painter’s masking tape is designed to seal neatly along the edge, reduce paint bleed, and remove cleanly when the job is done. Ideal for walls, trim, skirting boards, window frames, and any detail work where a sharp finish matters. Key Benefits Clean paint edges that help minimise bleed on most interior surfaces. Easy application with a smooth unwind and hand tearable backing. Clean removal when used as directed on properly prepared surfaces. Works with brushes, rollers, and spray for DIY and trade jobs. Perfect For Cutting in around ceilings, cornices, and trims Protecting hardware, switches, and fittings Two tone feature walls and accent colours Masking glass, tiles, and metal fixtures during repainting Surface Compatibility Use on properly prepared, fully cured interior paint, primed timber, metal, glass, and most smooth surfaces. Always test in an inconspicuous area first. How To Use Prep the surface: Ensure it is dry, dust free, and fully cured. Apply the tape: Press down firmly along the edge with a putty knife or fingernail to seal. Paint: Roll or brush away from the tape edge for best results. Remove: Peel back slowly at a 45 degree angle while paint is still slightly tacky, unless your coating specifies otherwise. Pro Tips Burnish the tape edge lightly to improve the seal on textured areas. Apply light coats near the edge. Heavy wet coats can overwhelm any mask. For long runs, overlap tape pieces by a few millimetres and press the overlap firmly. Good To Know Suitable for indoor projects and general decorating. Store in a cool, dry place away from direct sunlight to maintain performance. Available in popular widths to suit trim work and broad masking. Frequently Asked Questions Will it pull off fresh paint?Only apply to fully cured paint. Cure times vary by product and conditions. When in doubt, allow extra time and test first. Does it work on lightly textured walls?Yes, on many light textures, but press down firmly along the edge and use lighter coats near the tape line. Can I use it with spray equipment?Yes. Apply, seal the edge, and use controlled passes. Avoid flooding the tape line.

Read more less

Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®

Read more less

Usage Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates. Advantages Up to 4 hours fire resistance according to AS 1530.4 Up to 4 hours fire resistance according to EN 1366-4 Very good resistance to weathering Movement capability of ± 35% (ASTM C 719) Easy to smooth and very good workability Good adhesion to many different substrates Neutral curing   Colour Grey

Read more less

Selleys No More Gaps Interior Colours is a flexible gap filler available in a range of modern colours, to fill those unsightly gaps and cracks around the home and take away the need to paint. Features Available in a great colour range, so no need to paint. Paintable if required. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for long. Has greater than 350% elongation/stretch and up to +/- 20% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage Can be painted over with both water and oil-based paints, after the surface has skinned. (Approximately 30 minutes after application). Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack Is formulated for long term resistance to cracking and crumbling. Is water-based, so can be cleaned up with water. Will not stain building materials. Has good resistance to weathering. Mould and mildew resistance. Where can this product be used? Between window and door frames and the wall. Along skirting boards. Around cornices. Between benchtops and tiles which are not exposed to water. In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm.  What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Bare or painted surfaces Colorbond Many other building materials How To Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut the seal and nozzle and fit to the top of the cartridge. Insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun. Hold the caulking gun at a 45° angle and apply, forcing product into gap Smooth with a wet finger or spatula Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow surface to skin thoroughly prior to painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured. Avoid water contact until fully cured- 72 hours or longer in cold weather. Limitations: Not recommended for foot traffic areas, gaps between tongue and groove boards or weatherboard overlaps. Use Selleys(R) No More Gaps(R) Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards. Use Selleys(R) No More Gaps(R) Exterior & Weatherboard Gap Filler for weatherboard overlaps.  Not suitable for areas in prolonged contact with water eg. showers, pools & spas. Where significant joint movement occurs, or for areas of frequent water immersion, use the appropriate Selleys(R) Silicone  Sealant. Do not apply or store below 5°C.  Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying the product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. Allow the surfaces to the skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water-based undercoats and flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. Keep a pack of Selleys Sugar Soap Wipe handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.

Read more less

Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a grey, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.

Read more less