Loxeal

Loxeal Activator 11 Anaerobic Accelerator Spray 200ml Loxeal Activator 11 cleans, degreases and dramatically accelerates the cure of anaerobic adhesives and sealants – threadlockers, threadsealants, retaining compounds and gasketing products. It is the answer when anaerobic products cure slowly or unreliably: on passive surfaces (such as stainless steel, plated finishes and many alloys), at low temperatures, or across larger gaps. Spray one surface, let the solvent flash off for a few seconds, and fixture is typically achieved in 20–120 seconds. Supplied as a 200ml aerosol for fast, even coverage. Why choose Loxeal Activator 11? Speeds anaerobic fixture time to 20–120 seconds depending on adhesive, gap and temperature Cleans and degreases the joint in the same step Reliable curing in tough conditions – passive metals, cold workshops, larger gaps Long-lasting activation – treated parts remain active for up to three months when protected from dust and weathering Suitable for both threaded and flange joints Convenient 200ml aerosol spray application Typical applications Pre-treating stainless steel, zinc-plated and other passive fasteners before threadlocking or threadsealing Accelerating retaining compounds on bearings, bushes and cylindrical assemblies Speeding gasket and flange sealant cure in cold conditions or production settings How to use Spray Activator 11 onto one of the surfaces to be joined. Allow the solvent to evaporate for a few seconds until the surface is dry. Apply the anaerobic adhesive or sealant to the other surface. Assemble the parts; fixture typically occurs within 20–120 seconds. Specifications Composition Organic activating agents in solvent carrier Appearance Green liquid Viscosity (+25°C) 1–2 mPa·s Specific weight (+25°C) 0.8 g/ml Flash point (COC/DIN/ISO 2592) +21°C Cure acceleration Fixture in 20–120 seconds (adhesive, gap and temperature dependent) On-part activation life 24 hours; up to 3 months if parts are protected from dust and atmospheric agents Breakaway torque (ISO 10964, ref. 83-54) >5 Nm after 5 minutes Pack size 200ml aerosol spray Shelf life 1 year unopened at +25°C Important notes Use of an activator may reduce the final mechanical strength of the anaerobic bond Wait for the solvent to fully evaporate before assembling parts Flammable – keep away from ignition sources and use with good ventilation Store in a cool, dry place at no more than +25°C; do not refill containers with used product Safety Consult the Safety Data Sheet (SDS) before use. Flammable aerosol: keep away from heat, sparks and open flames, use in a well-ventilated area and avoid inhaling vapours. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

Loxeal 31-42 Clear 5-Minute Epoxy Adhesive 50ml Dual Cartridge Loxeal 31-42 is a two-part, fast-setting structural epoxy that cures colourless and transparent, making it ideal for repairs where the glue line needs to stay invisible. Supplied in a convenient 50ml dual cartridge (1:1 ratio) with a mixing nozzle, it dispenses perfectly proportioned adhesive with no weighing or hand mixing. With a working time of around 5 minutes and handling strength in 20–30 minutes, it bonds metals, ferrite, ceramic, marble, glass, concrete, wood and some rigid plastics. Why choose Loxeal 31-42? Dries clear – colourless, transparent bond line suits glass, ceramics and visible repairs Fast 5-minute set – 3–8 minute working time, functional strength in 20–30 minutes No-mess 1:1 dual cartridge with mixing nozzle for accurate, on-part dispensing Gap filling from 0.1 to 2.0 mm for less-than-perfect joints Durable bonds with excellent resistance to water, gasoline, motor oil and cooling gas Easy enough for DIY, strong enough for the workshop Typical applications Structural bonding of metals, ferrite, ceramic, marble, glass, concrete and wood Bonding some rigid plastics such as polyester, ABS and rigid PVC Joining dissimilar materials in one fast operation Household, automotive, hobby and workshop repairs needing a clear, rigid bond How to use Lightly abrade the surfaces, then degrease with Loxeal Cleaner 10 or acetone and allow to dry. Fit the mixing nozzle to the cartridge and discard the first 3–5 cm of extruded adhesive. Apply the mixed adhesive directly to one surface. Assemble the parts immediately and hold them together, without mechanical stress, until handling strength is reached. Remove uncured excess with acetone or a compatible solvent-based cleaner; cured adhesive can only be removed mechanically. Cure times Pot life (working time): 3–8 minutes at +25°C Functional cure: 20–30 minutes at +25°C Strength continues to develop over the following hours; gentle heat accelerates cure Specifications Chemistry Two-part epoxy (resin / amine hardener) Colour (mixed) Colourless / transparent Mixing ratio 1:1 by volume Pot life (+25°C) 3–8 minutes Functional cure 20–30 minutes Shear strength (steel, ISO 4587) 12–14 N/mm² Peel strength (ISO 4578) 4–20 N/25mm Hardness Shore D 65–75 Gap fill 0.1–2.0 mm Service temperature -40°C to +80°C Pack size 50ml dual cartridge (DCT) with mixing nozzle Shelf life 1 year unopened at +5°C to +25°C Important notes Not suitable for rubber, soft materials, polyethylene (PE), polypropylene (PP) or PTFE Apply at temperatures above +15°C; higher temperatures shorten pot life Avoid mixing large volumes at once – the chemical reaction generates heat Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Work in a well-ventilated area, avoid skin and eye contact, and keep out of reach of children. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

Loxeal Metalox Metal Repair Epoxy Kit 10 x 25ml Bi-Syringes Loxeal Metalox is a solvent-free, fast-curing, metal-filled two-part epoxy engineered for repairing and bonding metal components. This trade pack contains 10 x 25ml bi-syringes, each supplied with mixing nozzles, so every job starts with fresh, accurately proportioned adhesive. Its thixotropic (non-sag) paste works as an adhesive filler – rebuilding metal castings, pipework and flanges – and once cured it can be machined, sanded and painted, typically within a few hours of application. Why choose Loxeal Metalox? Trade pack of 10 x 25ml bi-syringes with mixers – fresh 1:1 dispensing on every repair Fast cure – handling strength in around 15 minutes, sandable in about 5 hours at room temperature Strong on steel – lap shear strength of 21 N/mm² on grit-blasted mild steel Machinable, sandable and paintable after polymerisation, even for outdoor repairs Non-sag thixotropic paste stays put on vertical and overhead surfaces Excellent resistance to water and many chemical agents Heat cure option: 1 hour at +60°C speeds cure and boosts final strength Typical applications Repairing metal castings, pipework and flanges Automotive body repair and panel filling Bonding metal substrates, plus concrete, wood and other rigid materials Maintenance and plant repairs where downtime must be kept short How to use Scratch or abrade the surface, then degrease with Loxeal Cleaner 10 or acetone and allow to dry. Fit the mixing nozzle to the bi-syringe and discard the first 3–5 cm of extruded product. Apply the mixed adhesive directly to the repair area; work at temperatures above +15°C. Assemble or shape immediately and leave undisturbed until cured. Once cured (sandable after about 5 hours at +25°C), machine, sand or paint as required. Cure times Pot life: approximately 5 minutes at +25°C Handling strength: approximately 15 minutes Sandable: about 5 hours at +25°C (90% of final hardness) Accelerated cure: 1 hour at +60°C for full resistance sooner Specifications Chemistry Two-part epoxy (resin / amine hardener), metal-filled Colour Part A metallic grey / Part B black Mixing ratio 1:1 by volume Pot life (+25°C) Approx. 5 minutes Handling strength Approx. 15 minutes Lap shear strength (ISO 4587) 21 N/mm² (grit-blasted mild steel); 18 N/mm² (stainless steel) Compression strength (ASTM D695) 60 N/mm² Hardness (ISO 868) Shore D 65 Pack size Trade pack: 10 x 25ml bi-syringes with mixing nozzles Shelf life 24 months unopened at +5°C to +25°C Important notes Apply at temperatures above +15°C; higher temperatures and large mixed quantities reduce pot life Avoid mixing excess product – the curing reaction generates heat Cured adhesive can only be removed mechanically Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Wear suitable gloves, avoid skin and eye contact, and work in a well-ventilated area. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

Loxeal 34-59T Structural Acrylic Adhesive Transparent Gel 150ml Loxeal 34-59T is the transparent gel version of Loxeal's 34-59 series – a fast-curing, chemically activated structural acrylic adhesive used together with a Loxeal Activator (such as Activator 20). No mixing is required: apply the adhesive to one surface and the activator to the other, press the parts together and the joint fixtures in as little as 20–40 seconds. The toughened, thixotropic gel is non-sag on vertical surfaces, bonds ferrites, metals and ceramics, and delivers a wide service temperature range up to +165°C. Supplied in a 150ml pack. Why choose Loxeal 34-59T? Transparent gel formulation for tidy, discreet bond lines No mixing required – cures on contact with the matching Loxeal Activator Very fast fixturing – typical handling time 20–40 seconds High strength – shear strength 20–30 N/mm² with strong impact resistance High temperature capability – service range -65°C to +165°C Non-sag gel suits vertical and overhead application Acid-free chemistry, ideal for high-speed assembly lines Typical applications Structural bonding of ferrites, metals and ceramics (e.g. magnet bonding in motors and speakers) High-speed production and assembly line joining Bonded joints exposed to elevated temperatures, impact and vibration How to use Clean both surfaces with Loxeal Cleaner 10 and allow to dry – water and grease prevent adhesion. Apply the Loxeal Activator to one surface and the adhesive gel to the other. Assemble and press the parts together until handling strength is achieved (20–40 seconds). For gaps larger than 0.5 mm, apply activator to both surfaces before applying the adhesive to one side. Remove excess uncured adhesive with an organic solvent and allow at least 24 hours for full cure before loading the joint. Cure times Handling time (with Activator 20): 20–40 seconds Functional cure: 10–20 minutes Full cure: 24 hours Specifications Chemistry Urethane methacrylate structural acrylic (chemically activated, no-mix) Form Transparent thixotropic gel Viscosity (+25°C) 15,000–25,000 mPa·s (thixotropic) Gap filling 0.05–0.20 mm (activator on both faces for larger gaps) Shear strength (ISO 4587) 20–30 N/mm² Tensile strength (ISO 6922) 20–25 N/mm² Impact strength (ASTM D950) 15–25 kJ/m² Service temperature -65°C to +165°C Pack size 150ml Shelf life 1 year unopened at +25°C Important notes Requires a Loxeal Activator (e.g. Activator 20), applied to the opposing surface – sold separately Not designed for polyolefins (PP/PE), PTFE or soft, flexible materials Store in a cool, dry place away from direct light, at no more than +25°C Specifications shown are for the Loxeal 34-59 series adhesive Safety Consult the Safety Data Sheet (SDS) before use. Avoid skin and eye contact and ensure good ventilation during application. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

Loxeal Superlox Polyolefin Bonder Kit 10 x 25ml Bi-Syringes Loxeal Superlox is a two-part acrylic adhesive developed to bond polyolefins – polypropylene (PP), polyethylene (PE), HDPE and LDPE – and other notoriously difficult low-surface-energy plastics, without primers, flame treatment or other expensive surface pre-treatments. This trade pack contains 10 x 25ml bi-syringes, each with mixing nozzles, dispensing the two components at a simple 1:1 ratio. It joins polyolefins to each other and to other plastics such as ABS and PVC, and to metals, producing structural joints with high shear and peel strength. Why choose Loxeal Superlox? Bonds the "unbondable" – PP, PE, HDPE and LDPE plus other low-surface-energy plastics No primer or surface pre-treatment required – clean, apply, assemble Trade pack of 10 x 25ml bi-syringes with mixers – fresh adhesive for every job Simple 1:1 mixing ratio through the supplied static mixing nozzles Structural performance – high shear and peel strength on plastics and mixed-material joints Also bonds polyolefins to other plastics (ABS, PVC) and to metals Typical applications Repairing and fabricating PP and PE components: tanks, housings, containers, piping and trim Joining polyolefin parts to dissimilar plastics or metal brackets and fittings Manufacturing and maintenance work on low-surface-energy plastic assemblies How to use Clean the surfaces to remove dust, oil and grease (for example with Loxeal Cleaner 10) and allow to dry. Fit the static mixing nozzle to the bi-syringe and discard the first few centimetres of extruded adhesive. Apply the mixed adhesive to one surface. Assemble the parts promptly and hold or clamp them without movement while the adhesive sets. Leave the joint undisturbed until fully cured before applying load. Cure times Fast curing at room temperature – parts typically fixture within minutes of assembly Allow 24 hours for full strength before placing joints under working load Refer to the Technical Data Sheet for precise fixture and cure data for your conditions Specifications Chemistry Two-part structural acrylic, polyolefin bonder Mixing ratio 1:1 by volume via static mixing nozzle Key substrates PP, PE, HDPE, LDPE and other low-surface-energy plastics; also ABS, PVC and metals Surface preparation No primer or pre-treatment required – clean and dry surfaces only Strength profile High shear and peel strength Pack size Trade pack: 10 x 25ml bi-syringes with mixing nozzles Important notes Work at room temperature; low temperatures slow the cure Use each mixing nozzle for one continuous application – fit a fresh nozzle if work is interrupted Cured adhesive can only be removed mechanically Store in a cool, dry place at no more than +25°C Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and avoid skin and eye contact. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

Loxeal Cleaner 10 Degreaser 1L Tin Loxeal Cleaner 10 is a non-CFC, solvent-based cleaner and degreaser formulated for preparing surfaces before bonding or sealing with adhesives and sealants. Great adhesion starts with a clean joint: Cleaner 10 lifts oil, grease and contamination, evaporates completely in around 60 seconds and is non-corrosive, leaving surfaces perfectly ready for adhesive. Importantly, it has no effect on the cure speed or final strength of Loxeal adhesives and sealants. This 1 litre tin is the economical choice for busy workshops and production benches. Why choose Loxeal Cleaner 10? Purpose-made for surface prep before threadlockers, retainers, epoxies, acrylics and instant adhesives Fast flash-off – dries in about 60 seconds at room temperature Non-corrosive and residue-free on metals Does not interfere with adhesive cure speed or bond strength Economical 1 litre tin for decanting or wipe application Non-CFC solvent formulation Typical applications Degreasing machined, treated or coated surfaces before bonding or sealing Cleaning oil- and grease-contaminated parts in maintenance and assembly work Preparing plastic substrates prior to adhesive application (check compatibility first) How to use Apply Cleaner 10 generously to the surfaces to be bonded. While the surface is still wet, wipe with a clean cloth to lift heavy contamination. Allow the solvent to evaporate until the surface is completely dry (about 60 seconds). Apply the adhesive or sealant immediately after drying and assemble the joint. Specifications Formulation Non-CFC solvent blend Appearance Colourless liquid Boiling range +92°C to +102°C Flash point (COC/DIN/ISO 2592) -1°C (highly flammable) Density (+25°C, DIN 51757) 0.70 g/ml Drying time (+25°C) Approx. 60 seconds Water solubility Not soluble Corrosivity None Pack size 1 litre tin Shelf life 12 months at +5°C to +25°C Important notes The solvent can affect certain plastics and coatings – check compatibility on a hidden area first Unclean or partially cleaned surfaces can significantly reduce adhesive performance Do not return used product to the original container Store between +5°C and +25°C in a cool, dry place Safety Consult the Safety Data Sheet (SDS) before use. Highly flammable: keep away from naked flames and non-flameproof electrical equipment, use only in well-ventilated areas, avoid prolonged or repeated skin contact and do not smoke near the product. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

Loxeal Cleaner 10 Degreaser Spray 400ml Loxeal Cleaner 10 is a non-CFC, solvent-based cleaner and degreaser for preparing surfaces before bonding or sealing with adhesives and sealants. This 400ml aerosol puts fast, controlled surface prep straight in your hand: spray, wipe, and the solvent flashes off in around 60 seconds leaving a clean, dry, non-corroded surface ready for adhesive. Cleaner 10 has no effect on the cure speed or final strength of Loxeal adhesives and sealants – but a dirty joint certainly will. Why choose Loxeal Cleaner 10 spray? Convenient aerosol application – even coverage on parts, threads and hard-to-reach areas Fast flash-off – dries in about 60 seconds at room temperature Non-corrosive and residue-free on metals Does not interfere with adhesive cure speed or bond strength Ideal partner for threadlockers, retainers, epoxies, structural acrylics and instant adhesives Non-CFC solvent formulation Typical applications Spray-degreasing fasteners, threads and machined parts before threadlocking or retaining Cleaning oil- and grease-contaminated surfaces in maintenance and assembly work Preparing treated, coated or plastic substrates prior to bonding (check compatibility first) How to use Spray Cleaner 10 directly onto the surfaces to be bonded. While still wet, wipe with a clean cloth to remove heavy contamination. Allow the solvent to evaporate until the surface is completely dry (about 60 seconds). Apply the adhesive or sealant immediately after drying and assemble the joint. Specifications Formulation Non-CFC solvent blend Appearance Colourless liquid Boiling range +92°C to +102°C Flash point (COC/DIN/ISO 2592) -1°C (highly flammable) Density (+25°C, DIN 51757) 0.70 g/ml Drying time (+25°C) Approx. 60 seconds Water solubility Not soluble Corrosivity None Pack size 400ml aerosol spray Shelf life 12 months at +5°C to +25°C Important notes The solvent can affect certain plastics and coatings – check compatibility on a hidden area first Unclean or partially cleaned surfaces can significantly reduce adhesive performance Pressurised container – protect from sunlight and do not expose to temperatures above +50°C Store between +5°C and +25°C in a cool, dry place Safety Consult the Safety Data Sheet (SDS) before use. Highly flammable aerosol: keep away from naked flames, sparks and non-flameproof electrical equipment, use only in well-ventilated areas, avoid prolonged skin contact and do not smoke near the product. Product information is provided as a general guide only. Always refer to the manufacturer's Technical Data Sheet and Safety Data Sheet, and test the product for suitability in your specific application before use.

Read more less

Loxeal Primer 7 Polyolefin Primer 20ml Loxeal Primer 7 is a solvent-based surface primer that makes the “unglueable” plastics glueable. Applied before a cyanoacrylate super glue, it raises the surface energy of polyethylene (PE), polypropylene (PP), thermoplastic rubbers, EPDM, PTFE and silicones, transforming bond strength on these notoriously low-energy materials. It dries in seconds, is fluorescent under blue light so coverage can be checked, and is recommended for use with Loxeal Istant 34 and other ethyl cyanoacrylate adhesives. Supplied in a 20ml bottle. Why choose Loxeal Primer 7? Unlocks polyolefins – makes PP, PE, PTFE, EPDM and silicone bondable with standard super glues Fast and simple – brush on a thin coat, wait a few seconds, then glue as normal Verifiable coverage – fluoresces under a blue lamp for quality control Long working window – primed surfaces stay active for up to one hour Ultra-thin, fluid consistency – roughly 1.5 mPa·s for even wetting of the surface Typical applications Bonding polypropylene and polyethylene parts, containers and housings PTFE, silicone rubber and EPDM components that resist ordinary adhesives Thermoplastic rubber grips, seals and trims Production and repair work on low surface energy plastics How to use Ensure surfaces are clean and dry. Brush a thin coat of Primer 7 onto the surfaces to be bonded and let it dry for a few seconds. Apply your cyanoacrylate adhesive and press the parts together – handling strength develops within seconds. Bond within one hour of priming for best results; reapply primer if more than eight hours pass. Reseal the bottle immediately after use. Usage notes Primer 7 is intended only for difficult, low surface energy materials – do not use it on substrates that bond readily without priming. Best adhesion is achieved when parts are joined within an hour of application. Specifications Chemistry Aliphatic amine in organic solvent Appearance Colourless; fluorescent under blue light Viscosity (+25°C) 1.5 mPa·s Specific weight (+25°C) 0.7 g/ml On-part life Bond within 1 hour; reapply after 8 hours Shelf life 1 year in original unopened packaging at +25°C Pack size 20ml bottle Important notes Solvent based – use in a well-ventilated area away from ignition sources. Store in a cool, dry place below +20°C and do not refill containers with used product. Seal the bottle immediately after each use to preserve the contents. Safety Consult the Safety Data Sheet (SDS) before use and wear suitable protection when handling. This information is provided as a general guide only. Always test on your specific materials and refer to the manufacturer's technical documentation before use.

Read more less

Loxeal Istant 23 Super Glue Fluid Cyanoacrylate Adhesive 100g Loxeal Istant 23 is a fluid, general purpose super glue built on ethyl cyanoacrylate chemistry. Its low viscosity (40–80 mPa·s) wicks neatly into close-fitting joints, and it bonds rubber, metal and most plastics in seconds by reacting with trace moisture on the surfaces. The medium setting speed leaves a short window to seat parts accurately before the adhesive grabs. This 100g workshop bottle is the economical choice for production lines, maintenance teams and busy workshops that go through super glue regularly. Why choose Loxeal Istant 23? Trade-size 100g bottle – keeps high-use workshops and production benches running Fluid, self-wicking formula – flows into tight joints with gaps of 10–60 microns Fast fixture – grabs in as little as 3–30 seconds on common plastics and metals Genuinely versatile – one bottle covers rubber, metals and most rigid plastics Solvent-free, single part – clear cure with tensile strength of 12–25 N/mm² Typical applications Production assembly and repetitive bonding tasks O-rings, seals and neoprene/NBR rubber components Maintenance and repair across rubber, metal and plastic parts Workshops and trades that need a reliable everyday instant adhesive in volume How to use Clean and degrease both surfaces and allow them to dry fully. Apply a small amount of adhesive to one surface only – with super glue, less is more. Bring the parts together promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. If setting is too slow, pair it with Loxeal Activator 9; for polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 40–80 mPa·s (fluid) Gap fill 10–60 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 12–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 100g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Prolonged exposure to very humid conditions can reduce long-term bond strength. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.

Read more less

Loxeal Istant 25 Super Glue Medium Viscosity Cyanoacrylate Adhesive 20g Loxeal Istant 25 is a medium-to-high viscosity super glue based on ethyl cyanoacrylate, designed for bonding plastic, rubber, metal and ceramic – including slightly irregular surfaces where a runny glue would simply drain away. At 350–450 mPa·s it stays where you put it, fills gaps up to 150 microns and fixtures in seconds, with a medium setting speed that gives you a moment to position parts. Supplied in a 20g bottle. Why choose Loxeal Istant 25? Medium viscosity – controllable application that stays put on the joint Handles imperfect surfaces – fills gaps of 10–150 microns Broad substrate range – plastic, rubber, metal and ceramic with one product Fast, strong fixture – tensile strength of 15–23 N/mm² when cured Solvent-free, single part – clean, clear bond line with no mixing Typical applications Repairs on ceramics, ornaments and household items Bonding rubber and plastic parts with less-than-perfect mating surfaces Metal-to-plastic and metal-to-rubber assemblies General workshop, trade and hobby bonding How to use Clean and degrease both surfaces and allow them to dry fully. Apply a modest bead or drops to one surface only. Assemble the parts promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; phenolic resin 5–20 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. For polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7; Loxeal Activator 9 can be used to speed up slow joints. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 350–450 mPa·s (medium) Gap fill 10–150 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 15–23 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.

Read more less

Loxeal Istant 43 Speciale Super Glue Cyanoacrylate Adhesive 50g Loxeal Istant 43 Speciale (43S) is a surface-insensitive, general purpose super glue based on modified ethyl cyanoacrylate. Unfazed by acidic and porous surfaces, it excels at bonding leather, wood, fabric, ceramic and metals where ordinary super glues struggle. It offers proven heat resistance to +120°C (short peaks to +150°C) and is NSF registered for use in and around food processing areas, making it a favourite for demanding trade and industrial work. Supplied in a 50g bottle. Why choose Loxeal Istant 43 Speciale? Surface insensitive – cures reliably on acidic and porous substrates like leather, wood and paper Heat resistant – holds strength up to +120°C, with short-term peaks to +150°C NSF registered – acceptable for use as an instant adhesive in and around food processing areas Very fast on hard-to-glue materials – fabric in 2–20 seconds, leather in 5–15 seconds Strong all-rounder – medium viscosity with tensile strength of 15–25 N/mm² Typical applications Leather goods, footwear and upholstery repairs Woodworking, trim and joinery fixes across many timber species Equipment maintenance around commercial kitchens and food processing plants Fabric, ceramic, metal and rubber bonding in workshops and on site How to use Clean and degrease all surfaces and allow them to dry before applying the adhesive. For low-energy plastics such as PE, PP or PTFE, apply Loxeal Primer 7 first and let it dry. Apply the adhesive sparingly to one surface, then bring the parts together quickly and correctly aligned – the fast cure leaves little room for repositioning. Press firmly for a few seconds until fixed, and keep parts clamped until fully set. Wait 24–72 hours for full cure before applying any mechanical stress. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: paper 1–5 seconds; fabric 2–20 seconds; PVC, ABS and phenolic resin 2–10 seconds; aluminium 2–10 seconds; steel 5–20 seconds; leather 5–15 seconds; ceramic 5–30 seconds; softwoods 5–20 seconds; oak 90–180 seconds. Loxeal Activator 9 can be used to accelerate slow joints. Full cure in 24–72 hours. Specifications Chemistry Modified ethyl cyanoacrylate Colour Clear Viscosity (+25°C) 80–150 mPa·s (medium) Gap fill 10–150 microns Fixture time 1–180 seconds, substrate dependent Full cure 24–72 hours Tensile strength 15–25 N/mm² (ISO 6922) Service temperature -50°C to +120°C (peaks to +150°C) Approvals NSF registered for food processing areas Shelf life 12 months in original unopened packaging Pack size 50g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Not approved for use with pure or gaseous oxygen. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.

Read more less

Loxeal Istant 23 Super Glue Fluid Cyanoacrylate Adhesive 20g Loxeal Istant 23 is a fluid, general purpose super glue built on ethyl cyanoacrylate chemistry. Its low viscosity (40–80 mPa·s) wicks neatly into close-fitting joints, and it bonds rubber, metal and most plastics in seconds by reacting with trace moisture on the surfaces. The medium setting speed leaves a short window to seat parts accurately before the adhesive grabs. Supplied in a 20g bottle that suits both the workbench and the kitchen drawer. Why choose Loxeal Istant 23? Fluid, self-wicking formula – flows into tight joints with gaps of 10–60 microns Fast fixture – grabs in as little as 3–30 seconds on common plastics and metals Genuinely versatile – one bottle covers rubber, metals and most rigid plastics Clear, strong bond line – colourless cure with tensile strength of 12–25 N/mm² Solvent-free, single part – no mixing, no clamping hardware, straight from the bottle Typical applications Everyday repairs across rubber, metal and plastic parts O-rings, seals and neoprene/NBR rubber components Small component assembly in production and maintenance work Household and hobby fixes where a fast, tidy bond is needed How to use Clean and degrease both surfaces and allow them to dry fully. Apply a small amount of adhesive to one surface only – with super glue, less is more. Bring the parts together promptly, align, and hold with light pressure for a few seconds. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; PVC 3–10 seconds; aluminium 5–15 seconds; steel 10–30 seconds; ABS 10–30 seconds; zinc 30–90 seconds. Allow up to 24 hours for full strength. If setting is too slow, pair it with Loxeal Activator 9; for polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 40–80 mPa·s (fluid) Gap fill 10–60 microns Fixture time 3–90 seconds, substrate dependent Tensile strength 12–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Prolonged exposure to very humid conditions can reduce long-term bond strength. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.

Read more less

Loxeal Istant 27 Super Glue High Viscosity Cyanoacrylate Adhesive 20g Loxeal Istant 27 is a high viscosity, gap-filling super glue based on ethyl cyanoacrylate, made for irregular surfaces on plastic, rubber, metal and ceramic. Its thick 1,200–1,800 mPa·s consistency bridges gaps up to 200 microns without running, and its deliberately slower fixture time lets you adjust and align parts during assembly before the bond locks in. Supplied in a 20g bottle. Why choose Loxeal Istant 27? High viscosity, gap-filling formula – fills gaps of 10–200 microns on uneven surfaces Stays where applied – thick consistency will not run out of the joint or drip Repositioning window – slower fixture allows parts to be adjusted during assembly Strong final bond – tensile strength of 18–25 N/mm² when cured Solvent-free, single part – clear cure straight from the bottle Typical applications Bonding rough, porous or poorly matched surfaces Plastic and rubber parts with irregular mating faces Ceramic repairs where a runnier glue would soak away or drip Assemblies that need a few extra seconds of alignment time How to use Clean and degrease both surfaces and allow them to dry fully. Apply a bead of adhesive to one surface only. Assemble the parts, adjust alignment while the slower fixture time allows, then hold with light pressure. Leave the joint undisturbed while strength develops; avoid heavy loads until fully cured. Cure times Fixture speed depends on the substrate, gap, temperature and humidity. Typical fixture times: neoprene/NBR under 5 seconds; phenolic resin 10–40 seconds; aluminium 10–30 seconds; ABS 15–40 seconds; PVC 20–50 seconds; steel 20–50 seconds; zinc 40–100 seconds. Allow up to 24 hours for full strength. For polyethylene, polypropylene, silicone rubber or PTFE, prime first with Loxeal Primer 7; Loxeal Activator 9 can be used to speed up slow joints. Specifications Chemistry Ethyl cyanoacrylate Colour Clear / colourless Viscosity (+25°C) 1,200–1,800 mPa·s (high) Gap fill 10–200 microns Fixture time 5–100 seconds, substrate dependent Tensile strength 18–25 N/mm² (ISO 6922) Service temperature -50°C to +80°C Shelf life 12 months in original unopened packaging Pack size 20g bottle Important notes Bonds skin instantly – avoid contact with skin and eyes, and keep away from children. Store in a cool, dry place below +20°C; refrigeration at +2°C/+7°C extends shelf life. Do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. Use in a well-ventilated area and wear suitable protection when handling. This information is provided as a general guide only. Always test the adhesive on your specific materials and refer to the manufacturer's technical documentation before use.

Read more less

Loxeal Activator 9 Cyanoacrylate Accelerator Spray 200ml Loxeal Activator 9 is an accelerator spray for cyanoacrylate super glues that cleans and degreases parts while slashing setting times. Sprayed onto one surface before assembly, it triggers cure in just 1–4 seconds – even on slow, dry or hard-to-activate substrates – and a treated surface stays active for up to 8 hours. It can also be misted over squeezed-out adhesive after assembly to fix the excess instantly. Supplied as a 200ml aerosol for fast, even coverage. Why choose Loxeal Activator 9? Cure in 1–4 seconds – turns slow joints into instant ones Cleans as it works – degreases parts in the same step 8-hour activation window – pre-treat parts ahead of assembly Fixes surplus glue – instantly sets excess adhesive outside the joint Convenient aerosol – quick, even application on parts of any shape Typical applications Speeding up cyanoacrylate cure on wood, porous and acidic surfaces Production assembly where consistent, rapid fixture times matter Cold or low-humidity conditions where super glue sets slowly Instantly curing glue fillets and squeeze-out for a tidy finish How to use Spray a light coat of Activator 9 onto one of the surfaces to be bonded. Allow it to dry for 20–30 seconds. Apply cyanoacrylate adhesive to the other surface and assemble the parts – cure takes effect in 1–4 seconds. To set surplus adhesive after assembly, mist it lightly with Activator 9. Usage notes Exact curing effect depends on the adhesive type, gap between parts and surface composition. Treated surfaces remain active for around 8 hours, so parts can be prepared in advance. Note that heavy over-application of activator can reduce ultimate bond strength on some joints. Specifications Chemistry Organic chemicals in solvent composition Appearance Colourless Viscosity (+25°C) 1–2 mPa·s Drying time (+25°C) 20–30 seconds Cure effect 1–4 seconds, adhesive and gap dependent Activation life on surface 8 hours Shelf life 12 months in original unopened packaging Pack size 200ml aerosol spray Important notes Solvent based aerosol – use in a well-ventilated area away from heat and ignition sources. Store in a cool, dry place below +20°C and do not refill containers with used product. Pair with Loxeal Istant cyanoacrylate adhesives for best results. Safety Consult the Safety Data Sheet (SDS) before use. Pressurised container – protect from sunlight and do not expose to temperatures exceeding +50°C. This information is provided as a general guide only. Always test on your specific materials and refer to the manufacturer's technical documentation before use.

Read more less

Loxeal 58-31 Gasketing Elastic Anaerobic Adhesive 75ml Loxeal 58-31 is a high-performance anaerobic gasketing adhesive that cures to an elastic, flexible film, replacing solid pre-formed gaskets on flange joints. It seals against gases, water, LPG, fuels, oils and a wide range of chemicals, resists shocks and vibration, and keeps sealing from -55°C right up to +180°C. The thixotropic consistency stops the sealant migrating before or during cure, and the red adhesive fluoresces under blue light for easy inspection on the production line. Why choose Loxeal 58-31? Elastic cured film accommodates joint movement while maintaining the seal Higher strength and faster fixture than general-purpose flange sealants Extended service temperature to +180°C Thixotropic — no running or migration on vertical flanges Fluorescent under blue light for quality-control checks Dismantles with standard tools when service is required Typical applications Sealing flange joints on pumps, gearboxes and differential housings where an elastic, vibration-resistant gasket and elevated temperature capability are needed — demanding automotive, transport and industrial maintenance work. How to use Clean and degrease the flange faces (Loxeal Cleaner 10 recommended). Apply enough product to fill the joint gap completely. Assemble the parts and hold them in place while curing. Use Loxeal Activator 11 for faster cure on passive metals or at low temperatures. To dismantle, use normal tools (heat to +150°C/+250°C if necessary), remove cured residue mechanically and clean with acetone. Cure times At +25°C on steel: handling strength in 10–20 minutes, functional strength in 1–3 hours and full cure in 6–12 hours. Cure speed varies with gap, substrate and temperature. Specifications Chemistry Anaerobic methacrylate Colour Red (fluorescent under blue light) Viscosity (+25°C) 70–600 Pa·s Specific gravity (+25°C) Approx. 1.1 g/ml Maximum gap fill 0.50 mm Breakaway torque (ISO 10964) 15–25 N·m Prevailing torque (ISO 10964) 18–28 N·m Shear strength (ISO 4587) 8–13 N/mm² Tensile strength (ISO 6922) 7–10 N/mm² Impact strength (ASTM D-950) 4–7 kJ/m² Service temperature -55°C to +180°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Fully cured Loxeal 58-31 offers excellent resistance to motor oil and gearbox oil at +125°C through 1,000 hours, excellent-to-good resistance to hot 50% water/glycol mixtures, and moderate resistance to gasoline on prolonged exposure. Important notes Recommended for metal surfaces — seek technical advice before applying to non-metal parts. Uncured adhesive can damage coatings, some plastics and elastomers, and may cause delayed stress-cracking in certain thermoplastics. Store cool and dry at no more than +25°C; do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.

Read more less

Loxeal 58-14 Gasketing Anaerobic Adhesive 75ml Loxeal 58-14 is a medium-strength anaerobic gasketing adhesive that forms a flexible in-place gasket between flange faces, doing away with pre-cut solid gaskets. The highly thixotropic formula stays exactly where it is applied without migrating before or during cure, and the cured film seals dependably against gases, water, LPG, fuels, oils and many other chemicals across a service range of -55°C to +150°C. Why choose Loxeal 58-14? One liquid gasket replaces an inventory of pre-formed paper, cork and plastic gaskets Flexible cured film shrugs off shocks and vibration Thixotropic — stays put on vertical and horizontal flanges Fills gaps up to 0.50 mm and compensates for minor surface imperfections Assemblies can be dismantled later with standard workshop tools Typical applications Gasketing and sealing of flange joints on pumps, gearboxes, differential housings and similar close-fitting metal assemblies in automotive workshops, plant maintenance and general engineering. How to use Clean and degrease both flange faces (Loxeal Cleaner 10 recommended). Apply a continuous bead so the joint gap is completely filled. Assemble the parts and hold them in position while the adhesive cures. On passive metals or in cold conditions, accelerate the cure with Loxeal Activator 11. To dismantle, use normal tools (heating the parts to +150°C/+250°C helps if needed), remove cured residue mechanically and clean up with acetone. Cure times At +25°C on steel: handling strength in 15–30 minutes, functional strength in 3–6 hours and full cure in around 24 hours. Cure speed varies with gap size, substrate and temperature. Specifications Chemistry Anaerobic methacrylate Colour Orange Viscosity (+25°C) 28,000–100,000 mPa·s, highly thixotropic Specific gravity (+25°C) Approx. 1.1 g/ml Maximum gap fill 0.50 mm Shear strength (ISO 4587) 5–10 N/mm² Tensile strength (ISO 6922) 5–8 N/mm² Impact strength (ASTM D-950) 3–5 kJ/m² Service temperature -55°C to +150°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Once fully cured, Loxeal 58-14 shows excellent resistance to motor oil and gearbox oil at +125°C out to 1,000 hours, and good long-term resistance to gasoline and to 50% water/glycol mixtures at +87°C. Important notes Formulated for metal surfaces — contact a technical adviser before use on non-metal parts. The liquid adhesive can attack coatings, some plastics and elastomers, and may induce delayed stress-cracking in certain thermoplastics. Store in a cool, dry place at no more than +25°C and never return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use and follow standard workshop hygiene practices. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.

Read more less

Loxeal 59-10 Gasketing High Temperature Anaerobic Adhesive 75ml Loxeal 59-10 is a single-component, medium-strength anaerobic flange sealant with outstanding heat resistance up to +200°C. It cures at room temperature when confined without air between close-fitting metal surfaces, forming a durable in-place gasket that replaces pre-formed gaskets, allows wider machining tolerances and still permits dismantling with normal tools. The cured seal is highly resistant to vibration, heat, water, gases, LPG, oils, fuels and many chemicals. Why choose Loxeal 59-10? Service temperature from -55°C to +200°C — ideal for hot-running assemblies Replaces pre-formed gaskets and assures true metal-to-metal contact Fills gaps up to 0.50 mm, accommodating greater machining tolerances Highly resistant to vibration, oils, hydrocarbons and coolants Parts remain serviceable — dismantle with everyday workshop tools Typical applications Sealing flat, rigid flange joints on pumps, gearboxes, camshaft blocks and motor flanges — anywhere a heat-tolerant, vibration-proof formed-in-place gasket is required. How to use Clean and degrease the mating surfaces (Loxeal Cleaner 10 recommended). Apply enough product to fill the joint gap completely. Bring the parts together and leave undisturbed until cured. On passivated surfaces or at low temperature, use Loxeal Activator 11 to speed the cure. For disassembly, use normal tools (heat to +150°C/+250°C if needed), remove cured residue mechanically and clean with acetone. Cure times At +25°C on steel: handling strength in 15–30 minutes, functional strength in 3–6 hours and full cure in 6–12 hours. Cure speed depends on substrate, gap and temperature. Specifications Chemistry Anaerobic methacrylate Colour Red Viscosity (+25°C) 50–300 Pa·s Specific gravity (+25°C) Approx. 1.05 g/ml Maximum gap fill 0.50 mm Shear strength (ISO 4587) 5–10 N/mm² Tensile strength (ISO 6922) 6–8 N/mm² Impact strength (ASTM D-950) 3–5 kJ/m² Service temperature -55°C to +200°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance After full cure, Loxeal 59-10 maintains excellent resistance to motor oil and gearbox oil at +125°C and to 50% water/glycol coolant at +87°C through 1,000 hours; resistance to gasoline is excellent initially, reducing with prolonged immersion. Important notes Recommended for metal surfaces — seek technical advice before use on non-metal parts. Liquid product may damage coated parts and elastomers, and contact with some thermoplastics can induce stress-cracking that is not immediately visible. Store in a cool, dry place at +25°C or below; never return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.

Read more less

Loxeal 30-22 UV-Curable High Viscosity Adhesive 50ml Loxeal 30-22 is a fast-curing, high-strength UV adhesive with a thicker, higher-viscosity consistency designed for glass-to-glass and glass-to-metal bonding. The heavier body gives better control on the joint and lets it bridge gaps up to 2 mm, while its crystal-clear, non-yellowing finish with over 98% light transmittance keeps even generous bond lines virtually invisible — ideal for precious crystal work. Why choose Loxeal 30-22? High viscosity (5,500–7,500 mPa·s) resists flowing off the joint before cure Fills bond lines from 0.03 mm up to 2 mm — more forgiving on uneven parts Cures in seconds under UV light (365 nm) Clear, colourless joints with excellent optical clarity Strong bonds on glass-to-glass and glass-to-metal assemblies Typical applications Glass-to-glass and glass-to-metal bonding in glass furniture, decorative items and crystal ware — especially assemblies with larger or less uniform bond gaps where a runnier adhesive would drain away. How to use Ensure both parts are clean and completely dry. Apply the adhesive to one surface and bring the parts together. At least one part must be UV-transparent — position the assembly before exposure. Cure with a UV source emitting between 365 nm and 420 nm (around 100 mW/cm² recommended); exposure of 6–10 seconds is typically sufficient. Extend the exposure for wider gaps or substrates that filter UV. Cure times Typical fixture under a suitable UV lamp is 6–10 seconds. Cure time varies with lamp intensity, distance from the light source, bond-line gap and the light transmittance of the substrate. Specifications Chemistry Methacrylate ester, UV-curing Colour Clear / colourless Viscosity (+25°C) 5,500–7,500 mPa·s Specific gravity 1.10 g/ml Gap fill 0.03–2 mm Tensile strength (ASTM D-2095-69) 8–12 N/mm² Hardness Shore D 50–65 Elongation at break 80–100% Light transmittance > 98% Refractive index 1.49 Service temperature -55°C to +120°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Important notes At least one bonded part must transmit UV light for the adhesive to cure. Cure speed drops with tinted or UV-filtering substrates — extend exposure accordingly. Store in a cool, dry place at no more than +25°C, away from daylight; do not return used product to the bottle. Safety Consult the Safety Data Sheet (SDS) before use and avoid looking directly at UV curing lamps without eye protection. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.

Read more less

Loxeal 85-86 Thread Sealant High Temperature Anaerobic Adhesive 50ml Loxeal 85-86 is a high strength anaerobic adhesive for locking and sealing threaded joints on all metals, in both free and forced matings. It maintains its sealing performance up to +200°C and offers high resistance to thermal shock, vibration, water, gas, oils, fuels, refrigerant fluids and many other chemicals – making it the choice for hot pipework, gas lines and demanding sealing jobs where standard sealants fall short. Why choose Loxeal 85-86? Seals and locks in one step with high mechanical strength Keeps sealing up to +200°C (service range -55°C to +200°C) Works on all metals, including free and press-fit assemblies Resists thermal shock, vibration, fuels, refrigerants and many chemicals Generous gap fill up to 0.30 mm on threads up to M56 / 2″ Green colour, fluorescent under blue light, for easy inspection Certified and approved Approved for gas-tight threaded joints to EN 751-1 (DIN-DVGW) WRAS approved for contact with wholesome (potable) water Compliant with the UBA (German Environment Agency) declaration for potable water use BAM certified as a sealant in the presence of gaseous oxygen up to 20 bar at +60°C Typical applications Sealing threaded joints on gas, steam, hot water and heating pipework Potable water fittings (observe the potable-water cure times below) Refrigeration, fuel and industrial fluid lines exposed to heat and vibration How to use Clean and degrease both threads with Loxeal Cleaner 10 and allow to dry. Apply a continuous bead circumferentially, 1–2 threads back from the leading edge, using enough product to give a complete seal. Assemble and tighten the joint, then wipe off any uncured excess. Allow to cure before pressurising. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 (this may reduce final strength). Cure times at +25°C Handling strength: 10–40 minutes Functional strength: 6–12 hours Full cure: 24–36 hours Before contact with potable water: allow 24 hours at +20°C for brass, copper and cast iron; 7 days for stainless steel and aluminium Specifications Chemistry Anaerobic methacrylate Colour Green (fluorescent under blue light) Viscosity (+25°C) 2,200–4,000 mPa·s Specific gravity (+25°C) 1.05 Max thread size / gap fill M56 / 2″ / 0.30 mm Shear strength (ISO 10123) 15–25 N/mm² Breakaway torque (ISO 10964) 25–35 N·m Prevailing torque (ISO 10964) 40–55 N·m Service temperature -55°C to +200°C Shelf life 1 year in original unopened packaging at up to +25°C Important notes Recommended for metal thread joints only – contact a technical service before use on other materials. Do not contaminate the adhesive with metal; cut the nozzle to the required bead size. The liquid product can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. High strength – for disassembly, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.

Read more less

Loxeal 30-20 UV-Curable Adhesive 50ml Loxeal 30-20 is a fast-curing, high-strength UV adhesive purpose-made for glass and crystal bonding. Under a suitable UV lamp it sets in as little as 6–10 seconds, and its water-clear finish with over 98% light transmittance makes joints all but invisible — the go-to choice for decorative tableware, household and furnishing accessories, giftware and fine crystal work. Why choose Loxeal 30-20? Cures in seconds under UV light (365 nm) — parts are handled almost immediately Exceptional optical clarity: clear, colourless, non-yellowing joints High bond strength on glass-to-glass and glass-to-metal assemblies Bridges bond lines from 0.03 mm up to 1.5 mm Convenient one-part product — no mixing, cures only where the light reaches Typical applications Bonding glass and crystal in decorative tableware, homewares, furnishing accessories, bonbonnières and gift articles; ideal for precious crystal pieces where the joint must stay invisible. How to use Ensure both parts are clean and completely dry. Apply a small amount of adhesive to one surface and bring the parts together. At least one part must be UV-transparent — align the assembly before exposure. Cure with a UV source emitting between 365 nm and 420 nm (around 100 mW/cm² recommended); exposure of 6–10 seconds is typically sufficient. Allow slightly longer exposure for larger gaps or tinted substrates. Cure times Typical fixture under a suitable UV lamp is 6–10 seconds. Actual cure time depends on lamp intensity, distance from the light source, bond-line gap and how much UV passes through the substrate. Specifications Chemistry Methacrylate ester, UV-curing Colour Clear / colourless Viscosity (+25°C) 2,200–2,900 mPa·s Specific gravity 1.1 g/ml Gap fill 0.03–1.5 mm Tensile strength (ASTM D-2095-69) 10–14 N/mm² Hardness Shore D 50–65 Elongation at break 80–100% Light transmittance > 98% Refractive index 1.49 Service temperature -55°C to +120°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Cured Loxeal 30-20 shows excellent long-term resistance to alcohol and refrigerant gases and good resistance to gasoline. Sustained exposure to high humidity (90% RH at +40°C) reduces bond performance, so it is best suited to dry indoor service. Important notes At least one bonded part must transmit UV light for the adhesive to cure. Cure speed drops with tinted or UV-filtering glass — extend exposure accordingly. Not recommended for permanently damp or wet environments. Store in a cool, dry place at no more than +25°C, away from daylight; do not return used product to the bottle. Safety Consult the Safety Data Sheet (SDS) before use and avoid looking directly at UV curing lamps without eye protection. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.

Read more less

Loxeal 55-03 Threadlocker Medium Strength Anaerobic Adhesive 10ml Loxeal 55-03 is a medium strength anaerobic threadlocker for nuts, bolts and studs of all types that may need to be dismantled later with standard hand tools. It tolerates minor oil contamination on the parts, so it keeps performing where threads are not perfectly clean. Once cured it resists vibration, corrosion, water, gas, oils, hydrocarbons and many other chemicals, and it holds its sealing properties from -55°C to +200°C (up to +250°C for short periods), with proven unscrewing resistance at +200°C. Why choose Loxeal 55-03? Medium strength – assemblies can be dismantled with normal tools when servicing is needed Tolerates light oil contamination on threads Locks and seals fasteners in one step, stopping loosening caused by vibration Wide service temperature range of -55°C to +200°C Blue colour, fluorescent under blue light, for easy inspection on the production line Seals the thread against ingress, helping prevent rust and fretting corrosion Certified and approved Approved as a gas-tight sealant for threaded fittings to European norm EN 751-1 (DVGW and Gaz de France) WRAS approved – suitable for use in contact with potable water Compliant with the UBA (German Environment Agency) declaration for potable water applications NSF registered in category S4 as acceptable for use as an adhesive in and around food processing areas Typical applications Securing nuts, bolts, studs and screws on machinery, vehicles and equipment subject to vibration Sealing threaded fittings on gas, water and compressed air lines Automotive, plumbing and general maintenance work where later disassembly must remain possible How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before putting the joint into service. On passive surfaces (e.g. stainless steel, plated parts) or in cold conditions, pre-treat with Loxeal Activator 11 to speed the cure (this may slightly reduce final strength). Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate resin Colour Blue (fluorescent under blue light) Viscosity (+25°C) 1,700–9,000 mPa·s, thixotropic Specific gravity (+25°C) 1.07 Max thread size / gap fill M36 / 0.25 mm Shear strength (ISO 10123) 9–13 N/mm² Breakaway torque (ISO 10964) 18–23 N·m Prevailing torque (ISO 10964) 9–16 N·m Service temperature -55°C to +200°C (+250°C short term) Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, ethanol and biodiesel, with good resistance to petrol, brake fluid, 50% water/glycol and acetone after 1,000 hours of exposure. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. Not approved for use with pure oxygen or oxygen-rich systems, and not suitable for sealing chlorine or other strong oxidising agents. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.

Read more less

Loxeal 55-14 Thread Sealant Anaerobic Adhesive 50ml Loxeal 55-14 is a medium strength anaerobic thread sealant for hydraulic and pneumatic threaded connectors up to 1-1/2″. It replaces PTFE tape and hemp for sealing against gases, water, LPG, hydrocarbons, oils and many other chemicals. A medium thixotropic consistency stops the sealant migrating out of the thread before or during cure, and the cured joint is highly resistant to heat, corrosion, shocks and vibration across a service range of -55°C to +150°C. Why choose Loxeal 55-14? General purpose sealer for hydraulic and pneumatic fittings up to 1-1/2″ Replaces PTFE tape and hemp – no shredding, no re-taping, no clogged valves Medium strength – joints can still be dismantled with normal tools Thixotropic formula stays on the thread instead of dripping or migrating Seals against gases, water, LPG, oils, hydrocarbons and many chemicals Resists shock, vibration and corrosion from -55°C to +150°C Typical applications Sealing threaded connectors on hydraulic and pneumatic systems Pipework carrying water, compressed air, LPG, oils and industrial fluids General plumbing and maintenance sealing of metal pipe threads How to use Clean and degrease both threads with Loxeal Cleaner 10 and allow to dry. Apply a bead of sealant around the male thread so the gap is completely filled. Assemble and tighten the connection. Allow to cure before pressurising. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to speed the cure. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 5–10 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Red (fluorescent under blue light) Viscosity (+25°C) 2,500–12,000 mPa·s, thixotropic Specific gravity (+25°C) 1.05 Max thread size / gap fill M56 / 2″ / 0.30 mm Shear strength (ISO 10123) 8–12 N/mm² Breakaway torque (ISO 10964) 12–18 N·m Prevailing torque (ISO 10964) 20–30 N·m Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Important notes Formulated for metal threads only – contact a technical service before use on other materials. The liquid sealant can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.

Read more less

Loxeal 53-11 Retaining Compound Anaerobic Adhesive 50ml Loxeal 53-11 is a medium strength anaerobic retaining compound for fixing bearings, liners, bushes, keys and splines into housings and onto shafts. It fills the space between cylindrical parts to give 100% surface contact, boosting load-carrying capacity while still allowing disassembly with standard workshop methods. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals across a service range of -55°C to +150°C. Why choose Loxeal 53-11? General purpose retainer for bearings, bushes, liners, keys and splines Medium strength – parts remain serviceable and can be dismantled Fills the joint completely, preventing fretting corrosion between mating parts Increases load transmission compared with a mechanical fit alone Low viscosity wicks into close-fitting cylindrical assemblies Resists vibration, oils, fuels and many chemicals from -55°C to +150°C Typical applications Retaining bearings and bushes in housings and on shafts Securing cylinder liners, keys, splines and sleeves Workshop repairs to restore security in worn cylindrical fits How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts, seating them fully, and hold in position for the cure time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Yellow (fluorescent under blue light) Viscosity (+25°C) 400–650 mPa·s Specific gravity (+25°C) 1.05 Max thread size / gap fill M20 / 0.12 mm Shear strength (ISO 10123) 8–12 N/mm² Breakaway torque (ISO 10964) 11–20 N·m Prevailing torque (ISO 10964) 15–25 N·m Impact strength (ASTM D-950) 1–5 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, petrol and brake fluid at +25°C (out to 5,000 hours), with good resistance to 50% water/glycol at +87°C. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.

Read more less

Loxeal 82-21 Retaining Compound Fast Cure Anaerobic Adhesive 50ml Loxeal 82-21 is a fast curing, high strength anaerobic retaining compound for close-fitting cylindrical parts – shafts, bushes, pulleys and rotors. Its low viscosity flows into precise fits, reaching handling strength in as little as 5–10 minutes, and cures to a tough bond with 17–22 N/mm² shear strength. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils and hydrocarbons across a service range of -55°C to +150°C. Why choose Loxeal 82-21? Fast fixture – handling strength in 5–10 minutes keeps jobs moving High strength bond for permanent retention of close-fitted parts Low viscosity penetrates precise cylindrical fits (up to 0.10 mm gap) High impact strength of 11–15 kJ/m² for parts under shock loading Fills the joint completely, preventing fretting corrosion Resists vibration and many chemicals from -55°C to +150°C Typical applications Bonding pulleys, gears and rotors onto shafts Retaining bushes and bearings in precision housings Production assembly where fast fixture times are needed How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts promptly, seating them fully, and hold for the fixture time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 5–10 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green Viscosity (+25°C) 120–180 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M12 / 0.10 mm Shear strength (ISO 10123) 17–22 N/mm² Breakaway torque (ISO 10964) 24–35 N·m Prevailing torque (ISO 10964) 50–60 N·m Impact strength (ASTM D-950) 11–15 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to refrigerants (Freon) at +25°C, excellent resistance to petrol out to 500 hours, and moderate resistance to motor and gearbox oils at +40°C over extended exposure. Important notes High strength – intended as a permanent retaining bond. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.

Read more less

Loxeal 83-54 Threadlocker High Strength Anaerobic Adhesive 50ml Loxeal 83-54 is a high strength anaerobic threadlocker for permanently locking and sealing studs, nuts, bolts and threaded fasteners that are not intended to be dismantled. It can be used on all metals, in both free and interference fits, and delivers high unscrewing resistance with temperature performance up to +200°C. The cured adhesive stands up to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals, making it a direct alternative to other high-strength studlocks such as Loctite 263. Why choose Loxeal 83-54? High strength, permanent locking for fasteners that must not come loose Strong prevailing torque of 50–65 N·m keeps holding even after the initial break Service temperature from -55°C to +200°C Suitable for all metals, in free or forced (press-fit) matings Green colour, fluorescent under blue light, for easy quality inspection Seals the thread, protecting against corrosion and leakage Typical applications Permanent locking of studs into engine blocks, housings and castings Heavy machinery, driveline and suspension fasteners exposed to strong vibration Fasteners on pumps, compressors and equipment where loosening would be a safety risk How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before loading the joint. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 5–10 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green (fluorescent under blue light) Viscosity (+25°C) 450–650 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M20 / 0.15 mm Shear strength (ISO 10123) 15–20 N/mm² Breakaway torque (ISO 10964) 25–35 N·m Prevailing torque (ISO 10964) 50–65 N·m Service temperature -55°C to +200°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to petrol and brake fluid at +25°C, good resistance to 50% water/glycol at +87°C, and good short-term resistance to motor and gearbox oils at +125°C (moderate on extended exposure). Important notes Designed as a permanent locking product – routine disassembly is not intended. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.

Read more less

Loxeal 55-03 Medium Strength Anaerobic Threadlocker Loxeal 55-03 is a medium strength anaerobic threadlocker for nuts and bolts of all types that may need to be dismantled later. It tolerates minor oil contamination on parts, so it performs even on as-received fasteners, and it holds its locking and sealing properties from -55°C to +200°C (up to +250°C for short periods). The direct alternative to Loctite 243. Why choose Loxeal 55-03 Oil tolerant: cures reliably on lightly oiled threads without extensive cleaning. High temperature: proven unscrewing resistance at +200°C. Serviceable strength: locks firmly against vibration yet can be dismantled with hand tools. Wide chemical compatibility: resists water, gas, oils, gasoline, brake fluid, ethanol, biodiesel and many chemicals. Blue colour, fluorescent under blue light for easy inspection. Certified and approved Gas: approved as gas-tight sealant for threaded fittings to EN 751-1 (DVGW and Gaz de France). Potable water: WRAS approved and compliant with the German UBA declaration for drinking water use. Food areas: NSF registered category S4 for use as an adhesive in and around food processing areas. Typical applications Locking machine bolts, pump housings, gearbox fasteners and automotive nuts and bolts subject to vibration. Threaded fittings in gas and potable water systems where certified products are required. Maintenance work on equipment where fasteners arrive lightly oiled. How to use Clean and degrease parts where practical (Loxeal Cleaner 10 recommended); minor oil films are tolerated. Apply enough product to completely fill the engaged threads. Assemble the parts and hold for the curing time. On passive surfaces or in cold conditions, Loxeal Activator 11 speeds curing (may slightly reduce final strength). Cure times at +25°C Handling: 10 to 20 minutes Functional: 1 to 3 hours Full cure: 24 to 36 hours depending on substrate, gap and temperature Specifications Chemistry Anaerobic methacrylate resin Colour Blue (fluorescent under blue light) Strength grade Medium (dismantlable) Viscosity at +25°C 1,700 to 9,000 mPa·s, thixotropic Specific gravity Approx. 1.07 g/ml Friction coefficient Approx. 0.10 Max thread / gap filling M36 / 0.25 mm Shear strength 9 to 13 N/mm² (ISO 10123) Breakaway torque 18 to 23 N·m (ISO 10964) Prevailing torque 9 to 16 N·m (ISO 10964) Service temperature -55°C to +200°C (+250°C short term) Approvals EN 751-1 (DVGW, Gaz de France), WRAS, UBA, NSF S4 Shelf life 1 year in unopened packaging at up to +25°C Chemical resistance Excellent long-term resistance to motor oil and gearbox oil at +125°C, ethanol and biodiesel at room temperature; excellent to good resistance to gasoline, brake fluid and 50 percent water glycol. Important notes For metal fasteners. Liquid product can damage coatings, some plastics and elastomers; stress cracking may develop with some thermoplastics. Not approved for pure oxygen or oxygen-rich systems, and not suitable as a sealant for chlorine or other strong oxidising agents. For disassembly use normal tools; if needed heat parts to +150°C to +250°C, remove cured residue mechanically and clean with acetone. Store cool and dry at or below +25°C. Do not return used product to the bottle. Safety Consult the Safety Data Sheet before use. For professional and industrial use. Follow all handling instructions on the product label. All technical information is provided as a guide only. Always verify suitability with your specific materials and operating conditions before use.

Read more less

Loxeal 24-18 Low Strength Anaerobic Threadlocker Loxeal 24-18 is a low strength anaerobic threadlocker for nuts, bolts and screws of all types that need to be easily dismantled later with ordinary hand tools. It locks fasteners against loosening from vibration and thermal cycling while staying serviceable, making it the go-to grade for small screws, adjustment fasteners and parts that see regular maintenance. Why choose Loxeal 24-18 Easy disassembly: low breakaway torque means fasteners come apart with standard tools, no heat needed in most cases. Anti-vibration: prevents self-loosening caused by vibration, shock and temperature changes. Wide chemical compatibility: resists water, gases, oils, gasoline, diesel and many chemicals. Gas approved: DVGW approved as a gas-tight sealant for threaded fittings to European norm EN 751-1. Service temperature from -55°C to +150°C. Purple colour, fluorescent under blue light for easy inspection. Typical applications Locking small screws, grub screws, calibration and adjustment fasteners that require frequent servicing. General automotive, machinery and DIY threadlocking where easy removal matters. Thread sealing of metal fittings where a low strength, dismantlable seal is acceptable. How to use Clean and degrease threads (Loxeal Cleaner 10 recommended). Apply enough product to fill the engaged threads. Assemble the parts and tighten as normal. Allow to cure before putting into service. On passivated surfaces or in cold conditions, use Loxeal Activator 11 to speed curing. Cure times at +25°C Handling: 15 to 30 minutes Functional: 1 to 3 hours Full cure: up to 24 to 36 hours depending on substrate, gap and temperature Specifications Chemistry Anaerobic methacrylate Colour Purple (fluorescent under blue light) Strength grade Low (easy to dismantle) Viscosity at +25°C 800 to 1,400 mPa·s Specific gravity Approx. 1.05 g/ml Max thread / gap filling M24 / 0.20 mm Shear strength 3 to 5 N/mm² (ISO 10123) Breakaway torque 5 to 8 N·m (ISO 10964) Prevailing torque 2 to 5 N·m (ISO 10964) Service temperature -55°C to +150°C Approvals DVGW gas-tight sealant, EN 751-1 Shelf life 1 year in unopened packaging at up to +25°C Chemical resistance Excellent resistance to gasoline and brake fluid at room temperature; excellent to good resistance to motor oil, gearbox oil and diesel at +125°C, and to 50 percent water glycol at +87°C. Important notes For metal fasteners. Liquid product can attack some coatings, plastics and elastomers; contact with some thermoplastics may cause stress cracking. Pre-test if unsure. For disassembly use normal tools; if needed heat parts to +150°C to +250°C, remove cured residue mechanically and clean with acetone. Store cool and dry at or below +25°C. Do not return used product to the bottle. Safety Consult the Safety Data Sheet before use. Follow all handling instructions on the product label. All technical information is provided as a guide only. Always verify suitability with your specific materials and operating conditions before use.

Read more less