Note :If you are working on a wooden floor, you will need to use the Fix-A-Floor Polyurethane For Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive " Now Patented", is an Extra Strength Bonding Adhesive customized for the specific use of Re-Bonding loose and hollow tile, marble & stone without the expense and mess of removing or replacing them. Fix-A-Floor is a simple do it yourself repair that is fast, easy and affordable not to mention fun and quite rewarding to anyone who can operate a drill, caulking gun and mix up a small batch of grout. Works on all sub-floor materials. Just Drill & Fill! The TipThe Tip of the 10.1 oz. Fix-A-Floor tube has been specially designed and engineered with a pre-drilled 1/8" hole for the sole purpose of filling drilled holes in loose & hollow tile, marble & stone floors. The Tip is extra firm and allows for a strong seal which promotes good flow and complete coverage. The 1/8" pre-drilled tip allows for use in narrow grout line applications or wider. It has marked lines showing clear cut points of 3/16", 1/4" or any other size you may need. The AdhesiveFix-A-Floor Repair Adhesive is Strong & Flexible with elastomeric bonding properties to eliminate any future problems due to foundation settlement, expansion & contraction of the sub floor as well as poor original installation... Used by professionals for years, now YOU can fix your loose & hollow, squeaky floors with Fix-A-Floor!!! Fix-A-Floor is Non-Toxic, Non-Flammable & Eco-Friendly! Large problem area or small problem areas are no problem with Fix-A-Floor! Guaranteed for the life of your floor! Just Drill & Fill! FAQs Q: Will Fix-A-Floor work if I have heated floors?A: Yes! We have customers using Fix-A-Floor with heated floor elements all the time with no problems. Keep heating element off before, during & for 48 hrs. after applying. Q: Some of my grout is missing or completely gone? How can I use Fix-A-Floor?A: If bits and pieces of grout are missing here and there around the problem area, just go ahead and Drill & Fill, the adhesive will actually help to re-bond the bits that are cracking and loose. If your grout is completely gone we recommend lightly re-grouting the area allow to dry and then Drill & Fill! Q: Can I use Fix-A-Floor to fix my entire floor or just a small area?A: Fix-A-Floor works great on all size problem areas from 1 tile to the whole entire floor! Works on all types of Tile, Marble & Stone floors too! Q: Can I use Fix-A-Floor outside on my patio or deck?A: Yes! Fix-A-Floor works beautifully on interior and exterior applications. Q: Can I use Fix-A-Floor in my shower or Pool?A: No! Fix-A-Floor is not recommended for areas with exposed to excessive moisture. Q: Is Fix-A-Floor Safe?A: Yes! Fix-A-Floor is a non-toxic, non-flammable and Eco-Friendly water-based adhesive. Q: Can I use Fix-A-Floor to re-glue a tile that is off the floor?A: Yes, simply squeeze Fix-A-Floor onto the floor where the tile was and press the tile back down onto the floor, place weight and allow to dry for 24 hrs. Tile will be rebonded! Q: Do I have to place buckets of water on my floor after I Drill & Fill?A: It is recommended you place some kind of weight on the area to aid in curing and to be sure no excess adhesive is trapped under your floor before regrouting. It is not mandatory. Q: What if I don’t see the adhesive coming up out of the other holes?A: While filling Fix-A-Floor will usually come up and out of the other drilled holes. If this does not happen move to another hole and continue to fill, the adhesive is still travelling under the floor. If you see the adhesive coming back up out of the hole you are filling, be sure you are NOT pressing the tip of the tube down onto the subfloor. Q: What if the adhesive is clumpy or not flowing out of the tube properly?A: The adhesive in the tube has frozen either in transit during the cold winter months this can happen. Simply contact us for a replacement.
$34.95
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be resoftened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$9.00
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$108.41
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$22.98
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.90
Clear Boyle Craft Glue Boyle Craft Glue (Clear) is a versatile, water-based adhesive designed for everyday making and detailed craft work. It dries clear and odourless, making it perfect for neat, mess-free results on paper projects, school assignments, scrapbooking, model making, décor builds and more. Why You’ll Love It Dries crystal clear for a clean, professional finish. Water-based & odourless for a low-fuss, indoor craft experience. Heat & light resistant—ideal for display pieces exposed to room lighting/sunlit interiors. Easy-squeeze bottle gives smooth, controlled bead lines and spot application. Cleans up with water—simply wipe while wet for quick tidy-ups. Suitable Materials Formulated for strong, reliable bonds on: Paper, cardboard & posters Wood, balsa & craft sticks Plastics* Glass & ceramics Metal embellishments Fabrics & felt Yarns, beads & sequins Leather and more *Always test first—some low-energy plastics may require light surface prep. Great For School projects & classroom crafts Cardmaking, scrapbooks & photo boards DIY décor, event styling & mood boards Miniatures, models & hobby builds Textile embellishment on felt and fabric (non-washwear items) How to Use Prep: Ensure surfaces are clean, dry and free of dust or oils. Lightly roughen very smooth surfaces for best grab. Apply: Squeeze a thin, even layer to one surface. For porous materials (paper, cardboard, wood), a little goes a long way. Assemble: Press parts together. Use light pressure, clips or tape if needed to hold while setting. Dry: Allow to dry thoroughly. Dry time varies with bead thickness, temperature and humidity. Clean-up: Wipe excess immediately with a damp cloth. Wash tools in water while glue is still wet. Good to Know Indoor use: Formulated for indoor crafting and display. Clear finish: Dries transparent to help hide glue lines and squeeze-out. Heat & light resistance: Helps projects maintain appearance under typical indoor conditions. Washes out with water: Clean hands, tools and fresh spills while wet. Specifications Base Water-based Appearance (dry) Clear Odour Odourless Cleanup Water (while wet) Use Indoor Tips & Testing For non-porous surfaces (glass, metal, some plastics), apply a thin coat to each surface, wait briefly, then join for better grab. Always perform a small test on off-cuts or an inconspicuous area to confirm compatibility and finish. Avoid heavy, load-bearing or structural applications—this is a craft-grade adhesive. FAQs Does it dry clear?Yes—Boyle Craft Glue dries clear for a neat finish. Can I wash it out?Yes—while wet, it washes out with water. Once fully dry/cured, removal may be more difficult. Is it suitable outdoors?It’s designed for indoor craft projects. For outdoor or constantly wet environments, choose a weather-rated adhesive.
$14.89
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697125187.jpg?v=1754724132&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125200.jpg?v=1754724131&width=645)
Selleys SolarFlex Selleys SolarFlex provides protection from ultraviolet (UV) radiation and other harsh weather elements. Harsh Australian and New Zealand conditions make the choice of an effective solar/weather protection solution critical. Features Superior weather protection Long-lasting flexibility No primer required before painting Watertight seal with a 10-year guarantee* Adhesion to wet or damp surfaces Non-bubbling Better curing and extrudability (>5°C) with no slump Paintable with water-based paints after product skins in 60 to 90 minutes Low VOC** Where can this product be used? Skylights Walls Patios Floors Fencing Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics* *Not suitable on polyethylene, polypropylene, or Teflon. Application Instructions Ensure substrates are clean and free of oil, grease, or loose particles. Cut the seal and nozzle, then fit it to the cartridge and place it in the caulking gun. Hold the caulking gun at a 45° angle and gun the sealant ahead of the nozzle, ensuring the product is pushed into the joint. For neat joints, use masking tape on both sides of the joint and remove it before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g., polyethylene backer rod) and appropriate joint width/depth. See the technical datasheet for more information. Limitations Not suitable on polyethylene, polypropylene, or Teflon. Cure excess product before disposal. Not for permanent water immersion or below water-line use. For water immersion, please use Selleys Marine Flex.
$23.92
Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications. Same formula & product you trust, just better looking! Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable. Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age. It is non-toxic, non-flammable & Solvent free 3-4 times stronger than standard P.V. High Solid content (51-53%) means more glue and it goes a lot further Does everything a P.V.A does, plus more Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.
$8.13
Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications. Same formula & product you trust, just better looking! Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable. Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age. It is non-toxic, non-flammable & Solvent free 3-4 times stronger than standard P.V. High Solid content (51-53%) means more glue and it goes a lot further Does everything a P.V.A does, plus more Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.
$103.00
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$24.43
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$12.75
Please refer to the photo of the back of the pack for indications and instructions
$15.00
Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance. Incredible bond strength Waterproof Superior strength Adheres to even visibly damp surfaces Longer work time (10 minutes)
$23.70
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$25.48
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$22.35
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$44.00
Selleys Craft Glue is a water-based PVA adhesive specially formulated for quick adhesion for craft work. The product is an off-white paste which is clear when dry. Features Easy to use – no mixing ready to use straight from the pack and only need to apply to one surface Fast Drying – initial bond can usually be achieved in a few seconds Dries clear Spills don’t stain and it’s easy to clean up with a wet rag Non-toxic – low odour and environmentally friendly Contains no flammable solvents Solvent-free – no fumes and non-flammable Appearance White milky liquid that dries clear Where can this product be used? Re-attach book cover/spine or repair torn bindings Craft/hobby work On very porous or open weave fabrics extra adhesive may be required for optimum bond strength Craft glue has limited water resistance In very cold or damp conditions the adhesive is slower setting What materials is this product suitable for? Fabrics Felt Cardboard Leather Suede Wood Paper Most plastic films (other than polyethylene and polypropylene) Sequins How to use this product Ensure surfaces to be joined are clean, dust and lint free. Shake bottle well before use. Unscrew cap to expose nozzle. Apply a thin coat of Selleys Craft Glue to one surface and press together. Hold in position with light pressure for a few seconds, or longer for very absorbent surfaces. Clean up excess glue quickly with a damp cloth. Wipe nozzle clean and replace cap after use. Handy tips On very porous surfaces applying a thin layer to each side and allowing it to soak in before applying a second layer to one side only may result in a stronger bond. Glue can be resoftened by soaking the item in warm water or by application of acetone. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. Safety tips Avoid eye contact, if contact occurs flush with plenty of water for 15 minutes and seek medical advice. Storage and re-use Clean up excess glue quickly with a damp cloth. Wipe nozzle clean and replace cap after use.
$15.00
Selleys Aquadhere Quick Set is a quick setting PVA wood glue that is suitable for all types of wood, sets twice as fast compared to normal PVAs and requires no clamping in many situations*. It will bond almost anything your craft work calls for! Features Fast bonding No clamping* Convenient and easy to use Non-toxic, water clean-up Dries clear *No need for clamping where joints are not under stress and timber is not bowed, warped etc Where can this product be used? School projects Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window frame Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Decorating What materials is this product suitable for? Interior wood Carboard Paper Fabric Felt Leather How to Use Surfaces to be bonded must be close fitting, dry and clean. Shake bottle and apply thinly to one surface. Press surfaces together firmly for 1-2 minutes. Wipe off excess adhesive with a damp cloth whilst still wet If joint is under stress or timber is bowed or warped, clamp until adhesive sets. Adhesive strength will be sufficient for object to be handled after 5-10 minutes for softwoods and 15-20 minutes for hardwoods. Allow 30-60 minutes before working with object. Maximum strength is attained in 4-8 hours. Allow longer setting/bonding time in cold or humid conditions. Limitations: Not for exterior use. Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere Quick Set is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Selleys Aquadhere exterior or Selleys Aquadhere Durabond). Will not take timber stains. Aquadhere Quick Set is not recommended for joints that are subjected to constant high stress. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Selleys Aquadhere Exterior.
$21.00
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before the adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High-Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many kinds of wood. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be softened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$6.00
$52.00
$29.03
$79.00
$40.16
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$15.74
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$68.31
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$11.52
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$8.12
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$14.76
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$7.86
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$19.67
This product is a quality PVA glue suitable for general woodworking. It is non-toxic, will not stain timber and dries clear. Suitable for Wood, Particle Board, Unglazed Pottery, Laminating, veneers, paper, cardboard, leather, foam and cloth Directions: Ensure all surfaces are clean, dry and free of oil, grease and wax Shake well before use Only apply to one surface Press surfaces together while the adhesive is still wet and clamp lightly (approx 2 to 4 hours in normal conditions) Remove excess glue with a damp cloth Great strength is achieved when dried overnight Cleaning: Clean up with water. Wash hands after use
$44.11
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$21.72
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.00
Note :If you are working on a wooden floor, you will need to use the Fix-A-Floor Polyurethane For Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive " Now Patented", is an Extra Strength Bonding Adhesive customized for the specific use of Re-Bonding loose and hollow tile, marble & stone without the expense and mess of removing or replacing them. Fix-A-Floor is a simple do it yourself repair that is fast, easy and affordable not to mention fun and quite rewarding to anyone who can operate a drill, caulking gun and mix up a small batch of grout. Works on all sub-floor materials. Just Drill & Fill! The Tip The Tip of the 10.1 oz. Fix-A-Floor tube has been specially designed and engineered with a pre-drilled 1/8" hole for the sole purpose of filling drilled holes in loose & hollow tile, marble & stone floors. The Tip is extra firm and allows for a strong seal which promotes good flow and complete coverage. The 1/8" pre-drilled tip allows for use in narrow grout line applications or wider. It has marked lines showing clear cut points of 3/16", 1/4" or any other size you may need. The Adhesive Fix-A-Floor Repair Adhesive is Strong & Flexible with elastomeric bonding properties to eliminate any future problems due to foundation settlement, expansion & contraction of the sub floor as well as poor original installation... Used by professionals for years, now YOU can fix your loose & hollow, squeaky floors with Fix-A-Floor!!! Fix-A-Floor is Non-Toxic, Non-Flammable & Eco-Friendly! Large problem area or small problem areas are no problem with Fix-A-Floor! Guaranteed for the life of your floor! Just Drill & Fill! FAQs Q: Will Fix-A-Floor work if I have heated floors? A: Yes! We have customers using Fix-A-Floor with heated floor elements all the time with no problems. Keep heating element off before, during & for 48 hrs. after applying. Q: Some of my grout is missing or completely gone? How can I use Fix-A-Floor? A: If bits and pieces of grout are missing here and there around the problem area, just go ahead and Drill & Fill, the adhesive will actually help to re-bond the bits that are cracking and loose. If your grout is completely gone we recommend lightly re-grouting the area allow to dry and then Drill & Fill! Q: Can I use Fix-A-Floor to fix my entire floor or just a small area? A: Fix-A-Floor works great on all size problem areas from 1 tile to the whole entire floor! Works on all types of Tile, Marble & Stone floors too! Q: Can I use Fix-A-Floor outside on my patio or deck? A: Yes! Fix-A-Floor works beautifully on interior and exterior applications. Q: Can I use Fix-A-Floor in my shower or Pool? A: No! Fix-A-Floor is not recommended for areas with exposed to excessive moisture. Q: Is Fix-A-Floor Safe? A: Yes! Fix-A-Floor is a non-toxic, non-flammable and Eco-Friendly water-based adhesive. Q: Can I use Fix-A-Floor to re-glue a tile that is off the floor? A: Yes, simply squeeze Fix-A-Floor onto the floor where the tile was and press the tile back down onto the floor, place weight and allow to dry for 24 hrs. Tile will be rebonded! Q: Do I have to place buckets of water on my floor after I Drill & Fill? A: It is recommended you place some kind of weight on the area to aid in curing and to be sure no excess adhesive is trapped under your floor before regrouting. It is not mandatory. Q: What if I don’t see the adhesive coming up out of the other holes? A: While filling Fix-A-Floor will usually come up and out of the other drilled holes. If this does not happen move to another hole and continue to fill, the adhesive is still travelling under the floor. If you see the adhesive coming back up out of the hole you are filling, be sure you are NOT pressing the tip of the tube down onto the subfloor. Q: What if the adhesive is clumpy or not flowing out of the tube properly? A: The adhesive in the tube has frozen either in transit during the cold winter months this can happen. Simply contact us for a replacement.
$65.00
Note: To apply this product you will need a syringe Fix-A-Floor Repair Adhesive " Now Patented", is an Extra Strength Bonding Adhesive customized for the specific use of Re-Bonding loose and hollow tile, marble, stone & creaky wood floors without the expense and mess of removing or replacing them. Fix-A-Floor is a simple do it yourself repair that is fast, easy and affordable not to mention fun and quite rewarding to anyone who can operate a drill, caulking gun and mix up a small batch of grout. Works on all sub-floor materials. Just Drill & Fill! The Adhesive Fix-A-Floor Repair Adhesive is Strong & Flexible with elastomeric bonding properties to eliminate any future problems due to foundation settlement, expansion & contraction of the subfloor as well as poor original installation... Used by professionals for years, now YOU can fix your loose & hollow, squeaky floors with Fix-A-Floor!!! Fix-A-Floor is Non-Toxic, Non-Flammable & Eco-Friendly! Large problem area or small problem areas are no problem with Fix-A-Floor! Guaranteed for the life of your floor! Just Drill & Fill! FAQs Q: Will Fix-A-Floor work if I have heated floors? A: Yes! We have customers using Fix-A-Floor with heated floor elements all the time with no problems. Keep heating element off before, during & for 48 hrs. after applying. Q: Some of my grout is missing or completely gone? How can I use Fix-A-Floor? A: If bits and pieces of grout are missing here and there around the problem area, just go ahead and Drill & Fill, the adhesive will actually help to re-bond the bits that are cracking and loose. If your grout is completely gone we recommend lightly re-grouting the area allow to dry and then Drill & Fill! Q: Can I use Fix-A-Floor to fix my entire floor or just a small area? A: Fix-A-Floor works great on all size problem areas from 1 tile to the whole entire floor! Works on all types of Tile, Marble Stone & Loose Wood floors too! Q: Can I use Fix-A-Floor outside on my patio or deck? A: Yes! Fix-A-Floor works beautifully on interior and exterior applications. Q: Can I use Fix-A-Floor in my shower or Pool? A: No! Fix-A-Floor is not recommended for areas with exposed to excessive moisture. Q: Is Fix-A-Floor Safe? A: Yes! Fix-A-Floor is a non-toxic, non-flammable and Eco-Friendly water-based adhesive. Q: Can I use Fix-A-Floor on my creaky wood floors? A: Definitely! Fix-A-Floor works great on creaky, squeaky wood floors and laminate too! Q: Can I use Fix-A-Floor to re-glue a tile that is off the floor? A: Yes, simply squeeze Fix-A-Floor onto the floor where the tile was and press the tile back down onto the floor, place weight and allow to dry for 24 hrs. Tile or wood will be rebonded! Q: Do I have to place buckets of water on my floor after I Drill & Fill? A: It is recommended you place some kind of weight on the area to aid in curing and to be sure no excess adhesive is trapped under your floor before regrouting. It is not mandatory. Q: What if I don’t see the adhesive coming up out of the other holes? A: While filling Fix-A-Floor will usually come up and out of the other drilled holes. If this does not happen move to another hole and continue to fill, the adhesive is still travelling under the floor. If you see the adhesive coming back up out of the hole you are filling, be sure you are NOT pressing the tip of the tube down onto the subfloor. Q: What if the adhesive is clumpy or not flowing out of the tube properly? A: The adhesive in the tube has frozen either in transit during the cold winter months this can happen. Simply contact us for a replacement.
$85.00
Attach items to paper, wood, cloth, pottery, and more with the non-toxic adhesive of Elmer's Washable School Glue. Specially formulated to be washable and easy to use, Elmer's School Glue perfect for school projects and home arts and crafts. Elmer’s School Glue is adjustable before setting and does not run, delivering reliable results with every use. You can also use your liquid glue to create glue slime! Four 5-ounce bottle of Elmer's Clear Washable School Glue. How can I un-clog my glue cap and what’s the proper way to clean it? The glue caps can actually be taken apart to help remove any blockage. Simply open the cap as far as it will go and then pull the orange part straight up and it should "pop" off. This should allow you to easily access any blockage. The blockage can be cleared with something like a toothpick or paper clip. You can also soak these separated parts in room temperature water which should help to more easily free up any blockage. Once clear, the orange part can simply be pressed/snapped back into position. Watch the how-to un-clog a glue cap video for visual instructions. Is glue made from horses or other animals? No, Elmer's does not make glue from horses or use animals or animal parts. Elmer's products are made from synthetic materials and are not derived from processing horses, cows or any other animals. Why doesn't glue stick to inside of the bottle? As long as the glue remains inside the bottle away from air it will remain fluid. Glue hardens when there is a loss of water from the formula. Exposure to the atmosphere will cause the water to evaporate and make the glue harden. That's why it is important to keep the cap on the glue bottle closed to prevent hardening or drying out. I have a milk allergy. Are your products safe for me to use? Elmer's products are derived from synthetic materials, not any type of animal or milk protein. Of course, if you experience any kind of allergic reaction, be sure to check with your doctor regardless of the type of product you are using. How long can I keep glue? If stored properly and capped tightly, Elmer's school glues and wood glues have an average shelf life of 2 years. Krazy Glue, also known as a cyanoacrylate, has a shelf life of approximately 12 - 18 months. Is Elmer's glue gluten free? All of Elmer's products are gluten free except for the Elmer's Finger Paints. The finger paints contain wheat and oat products. Is Elmer's glue acid free? No. Most of Elmer's glues that are acid-free are labelled as such. Some of Elmer's most popular acid-free products include all of Elmer's glue stick, rubber cement and spray adhesive products.
$4.79
Elmer’s School Glue is a washable, no-run glue that is easy to use and stays where you put it. - It is safe, non-toxic and washable, so accidental messes mean easy clean-up! - Perfect for making slime - Colour: White How can I un-clog my glue cap and what’s the proper way to clean it? The glue caps can actually be taken apart to help remove any blockage. Simply open the cap as far as it will go and then pull the orange part straight up and it should "pop" off. This should allow you to easily access any blockage. The blockage can be cleared with something like a toothpick or paper clip. You can also soak these separated parts in room temperature water which should help to more easily free up any blockage. Once clear, the orange part can simply be pressed/snapped back into position. Watch the how-to un-clog a glue cap video for visual instructions. Is glue made from horses or other animals? No, Elmer's does not make glue from horses or use animals or animal parts. Elmer's products are made from synthetic materials and are not derived from processing horses, cows or any other animals. Why doesn't glue stick to inside of the bottle? As long as the glue remains inside the bottle away from air it will remain fluid. Glue hardens when there is a loss of water from the formula. Exposure to the atmosphere will cause the water to evaporate and make the glue harden. That's why it is important to keep the cap on the glue bottle closed to prevent hardening or drying out. I have a milk allergy. Are your products safe for me to use? Elmer's products are derived from synthetic materials, not any type of animal or milk protein. Of course, if you experience any kind of allergic reaction, be sure to check with your doctor regardless of the type of product you are using. How long can I keep glue? If stored properly and capped tightly, Elmer's school glues and wood glues have an average shelf life of 2 years. Krazy Glue, also known as a cyanoacrylate, has a shelf life of approximately 12 - 18 months. Is Elmer's glue gluten free? All of Elmer's products are gluten free except for the Elmer's Finger Paints. The finger paints contain wheat and oat products. Is Elmer's glue acid free? No. Most of Elmer's glues that are acid-free are labelled as such. Some of Elmer's most popular acid-free products include all of Elmer's glue stick, rubber cement and spray adhesive products.
$24.20
Elmer’s School Glue is a washable, no-run glue that is easy to use and stays where you put it. - It is safe, non-toxic and washable, so accidental messes mean easy clean-up! - Perfect for making slime - Colour: White - Pack size: 225ml How can I un-clog my glue cap and what’s the proper way to clean it? The glue caps can actually be taken apart to help remove any blockage. Simply open the cap as far as it will go and then pull the orange part straight up and it should "pop" off. This should allow you to easily access any blockage. The blockage can be cleared with something like a toothpick or paper clip. You can also soak these separated parts in room temperature water which should help to more easily free up any blockage. Once clear, the orange part can simply be pressed/snapped back into position. Watch the how-to un-clog a glue cap video for visual instructions. Is glue made from horses or other animals? No, Elmer's does not make glue from horses or use animals or animal parts. Elmer's products are made from synthetic materials and are not derived from processing horses, cows or any other animals. Why doesn't glue stick to inside of the bottle? As long as the glue remains inside the bottle away from air it will remain fluid. Glue hardens when there is a loss of water from the formula. Exposure to the atmosphere will cause the water to evaporate and make the glue harden. That's why it is important to keep the cap on the glue bottle closed to prevent hardening or drying out. I have a milk allergy. Are your products safe for me to use? Elmer's products are derived from synthetic materials, not any type of animal or milk protein. Of course, if you experience any kind of allergic reaction, be sure to check with your doctor regardless of the type of product you are using. How long can I keep glue? If stored properly and capped tightly, Elmer's school glues and wood glues have an average shelf life of 2 years. Krazy Glue, also known as a cyanoacrylate, has a shelf life of approximately 12 - 18 months. Is Elmer's glue gluten free? All of Elmer's products are gluten free except for the Elmer's Finger Paints. The finger paints contain wheat and oat products. Is Elmer's glue acid free? No. Most of Elmer's glues that are acid-free are labelled as such. Some of Elmer's most popular acid-free products include all of Elmer's glue stick, rubber cement and spray adhesive products.
$6.50
Boyle Twisters contains 5 fun twisted glitter glue pens. It can be used on most surfaces such as paper, fabric, wood, plastic, glass, metal, tin and much more. Ideal for many craft projects to create fun. Quick Drying Ideal for most handicrafts Airtight Cap Boyle craft glue is ideal to use on paper, cardboard, wood, plastic, glass, ceramics, metal, fabrics, felt, yarns, beads, sequins, leather and much more.
$6.99
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Pink]](http://gluesaustralia.com.au/cdn/shop/files/9314235_0fda3f36-74b9-4f76-87c5-eecf1c56afcc.jpg?v=1754715680&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Pink]](http://gluesaustralia.com.au/cdn/shop/files/9314235_3922d4f4-2f1d-4263-a2de-14b767df10ba.jpg?v=1754715681&width=645)
$9.49
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Orange]](http://gluesaustralia.com.au/cdn/shop/files/9314235_fada9554-ceb7-411e-9690-c908a0973b94.jpg?v=1754715678&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Orange]](http://gluesaustralia.com.au/cdn/shop/files/9314235_b6829499-6c70-4712-bf76-ae02aa34ac1d.jpg?v=1754715678&width=645)
$9.49
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Green]](http://gluesaustralia.com.au/cdn/shop/files/9314235_e4f50d8f-e0a6-4255-a242-9c3e7590f0f3.jpg?v=1754715675&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Green]](http://gluesaustralia.com.au/cdn/shop/files/9314235_e401b93c-d8cb-46ff-be50-3f30c2495024.jpg?v=1754715675&width=645)
$9.49
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Blue]](http://gluesaustralia.com.au/cdn/shop/files/9314235_84aa9bc6-f55e-40c0-afbe-820db6fddb04.jpg?v=1754715673&width=645)
![Boyle Glow In The Dark Sparkling Craft Glue Kids Safe 147ml [Colour: Blue]](http://gluesaustralia.com.au/cdn/shop/files/9314235_0c7f6c0e-695e-4545-a57c-1e5bf7ca1f0c.jpg?v=1754715673&width=645)
$9.49
Apply to your arts, crafts, slime and school projects for a luminous glow. Expose to bright light for minimum 2 minutes. Switch off the lights and watch it glow. When glow fades, expose to light again.
$9.49
Non-Toxic Washable Extra Strength Safe for children Boyle PVA Glue is ideal to bond paper, wood, cork, ceramic, porcelain, fabrics, leather and much more.
$3.38
Quick Drying Ideal for most handicrafts Airtight Cap Boyle craft glue is ideal to use on paper, cardboard, wood, plastic, glass, ceramics, metal, fabrics, felt, yarns, beads, sequins, leather and much more.
$9.49
Quick Drying Ideal for most handicrafts Airtight Cap Boyle craft glue is ideal to use on paper, cardboard, wood, plastic, glass, ceramics, metal, fabrics, felt, yarns, beads, sequins, leather and much more.
$3.08
An adhesive for general woodworking applications. It is also ideal for Art and Craft applications and school supplies. Great to make slime. Ideal to bond paper wood, ceramic, porcelain and fabrics. Boyle PVA glue is suitable for porous surfaces such as wood, laminated board, leather, textiles, cork, paper, felt, styrene foam, cardboard, paper mache, decoupage collage, fabric flowers and more. Non-toxic Dries clear
$14.00
You have seen 48 out of 53 products
Water-based adhesives for wood, paper and porous materials. Choose interior or exterior grades as required; many dry clear and sand well for clean finishes. Clamp time and open time vary by formulation—check your project’s needs. Great for joinery, crafts and school use with easy water clean-up. Use filters to refine by set speed, finish and temperature rating. Always review the product page and TDS/SDS.
