For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 58-11 Anaerobic Thread Sealant Loxeal 58-11 is a high performance anaerobic sealant designed for metal thread joints only. It replaces PTFE tape and cord, delivers instant sealing against moderate pressure, and cures to form a shock and vibration resistant seal that remains reliable from -55°C to +150°C. Why choose Loxeal 58-11 Instant sealing against moderate pressure to get systems back in service fast. Thixotropic formulation stays where you put it and resists migration on threads. Wide chemical compatibility including gas, water, LPG, hydrocarbons, oils and more. Shock and vibration resistant for durable, leak free joints. Temperature range from -55°C to +150°C for tough Australian conditions. Certified and approved Gas approvals: DVGW and DIN EN 751-1, plus Australian Gas Association for working pressure up to 20 bar. Oxygen service: Approved for gaseous oxygen up to 10 bar at +60°C. Potable water: WRAS listed and suitable for contact with wholesome water. Also approved for contact with drinking water by Global Mark. Food area use: NSF registered category S4 for use as an adhesive in and around food processing areas. Hydrogen: Tested by KIWA as a sealant for use with pure hydrogen to EN 751-1. Typical applications Sealing tapered and parallel metal threaded fittings in plumbing, HVAC, gas and hydraulic systems. Replacing PTFE tape or thread cord on metal pipework where a permanent, pressure resistant seal is needed. Directions Clean and degrease threads thoroughly. Cut the nozzle to the required bead size. Apply a continuous bead 1 to 2 threads back from the leading edge. Ensure full coverage around the circumference. Assemble and tighten the joint. Wipe away excess uncured material. Allow to cure (see Cure times). Cure speed can be accelerated on passive metals or at low temperature with an appropriate activator. Cure times at +25°C Handling: 15 to 30 minutes Functional: 1 to 3 hours Time to water service for potable water systems at +21.1°C Brass, copper, cast iron: 24 hours Stainless steel, aluminium: 7 days Technical data Chemistry Anaerobic methacrylate Colour Yellow (fluorescent under blue light) Viscosity at +25°C 20,000 to 80,000 mPa·s, thixotropic Specific gravity Approx. 1.1 g/ml Gap filling Up to 0.30 mm (M56 / 2 inch) Flash point Greater than +100°C Shear strength 6 to 13 N/mm² (ISO 10123) Breakaway torque 18 to 24 N·m (ISO 10964) Prevailing torque 7 to 14 N·m (ISO 10964) Service temperature -55°C to +150°C Shelf life 1 year in unopened packaging at ? +25°C Chemical resistance Excellent resistance to motor oil, gearbox oil, gasoline and hydraulic oil. Excellent to good resistance in 50 percent water glycol at elevated temperature. Limitations and notes For metal to metal threaded joints only. Not suitable for plastic threads or rubber components. Liquid product can attack some coatings and plastics. Pre test if unsure. For disassembly, use normal tools. Heat components to approximately +150°C to +250°C if required, then remove cured residue mechanically and clean with solvent. Store in a cool, dry place at or below +25°C. Do not return unused product to the bottle. All technical information is provided as a guide only. Always verify suitability with your specific materials, operating pressures and local regulations before use. Follow all safety and handling instructions on the product label and safety data sheet.
$19.31
LOCTITE 263 is designed for the permanent locking and sealing of threaded fasteners. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. It's particularly suited for heavy duty applications such as studs into motor housings, nuts onto studs in pump housings and other fasteners where high strength is required. LOCTITE 263 provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids. Recommended on High strength Locks studs against vibration loosening Controlled/torque tension Prevents thread corrosion Fast curing How to use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole. For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours. Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush. For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 4. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 5. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 6. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 7. Assemble and tighten as required For Disassembly 1. Apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush
$18.13
Threadlocking Adhesive - medium strength. General purpose. Suitable for all metal threaded assemblies. LOCTITE® 243 is a general purpose threadlocker of medium bond strength. This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration. The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces. It is proven to be tolerant of minor contamination due to industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids. Prevents loosening on vibrating assemblies, e.g. pumps, gearboxes or presses. Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces). Proven to tolerate minor contamination by industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids Permits disassembly with hand tools for servicing Technology: Acrylic Chemical Type: Dimethacrylate ester Appearance (uncured) Blue liquidLMS Fluorescence Positive under UV lightLMS Components One component - requires no mixing Viscosity Medium, thixotropic Cure Anaerobic Secondary Cure Activator Application Threadlocking Strength Medium LOCTITE® 243™ is designed for the locking and sealing of threaded fasteners which require normal disassembly with standard hand toolsThe product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature of LOCTITE® 243™ reduces the migration of liquid product after application to the substrateLOCTITE® 243™ provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Safety Data Sheet (SDS). Where aqueous washing systems are used to clean the surfaces before bonding, it is important to check for compatibility of the washing solution with the adhesive. In some cases, these aqueous washes can affect the cure and performance of the adhesive. This product is not normally recommended for use on plastics (particularly thermoplastic materials where stress cracking of the plastic could result). Users are recommended to confirm the compatibility of the product with such substrates. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. Shake the product thoroughly before use 4. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 5. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 6. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 7. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 8. Assemble and tighten as required For Disassembly 1. Remove with standard hand tools 2. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot 3. Apply localized heat to the assembly to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush
$18.07
Loctite 222 Threadlocker prevents corrosion, loosening from shock or vibration, and seals to prevent leakage. It also allows for simple, hand tool disassembly without shearing the screw. Easy to remove, it is typically used with small screws up to 1/4 inch. Recommended on Low strength Stops vibration loosening of screws and seals against leakage Prevents thread corrosion Dismantle with normal hand tools How to Use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole. For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours. Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush. For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot.
$18.13
Hold It Australia T90 PENETRATOR Wicking Grade for Close Fitting Parts - 50ml Description: HOLDIT AUSTRALIA T90 Penetrant is a fast-curing, low viscosity anaerobic compound that seeks voids in assembled components to cure anaerobically on close-fitting metal parts. It's ideal for securing tightly fitted assemblies. Applications T90 is excellent for post-assembly application, effectively preventing loosening of metal threaded fasteners. It is suitable for securing parts with minimal clearance and repairing hairline cracks in metal castings. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. For porosity or hairline cracks in casting products, brush directly onto the parts. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the flange faces first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 58-31 Gasketing Elastic Anaerobic Adhesive 75ml Loxeal 58-31 is a high-performance anaerobic gasketing adhesive that cures to an elastic, flexible film, replacing solid pre-formed gaskets on flange joints. It seals against gases, water, LPG, fuels, oils and a wide range of chemicals, resists shocks and vibration, and keeps sealing from -55°C right up to +180°C. The thixotropic consistency stops the sealant migrating before or during cure, and the red adhesive fluoresces under blue light for easy inspection on the production line. Why choose Loxeal 58-31? Elastic cured film accommodates joint movement while maintaining the seal Higher strength and faster fixture than general-purpose flange sealants Extended service temperature to +180°C Thixotropic — no running or migration on vertical flanges Fluorescent under blue light for quality-control checks Dismantles with standard tools when service is required Typical applications Sealing flange joints on pumps, gearboxes and differential housings where an elastic, vibration-resistant gasket and elevated temperature capability are needed — demanding automotive, transport and industrial maintenance work. How to use Clean and degrease the flange faces (Loxeal Cleaner 10 recommended). Apply enough product to fill the joint gap completely. Assemble the parts and hold them in place while curing. Use Loxeal Activator 11 for faster cure on passive metals or at low temperatures. To dismantle, use normal tools (heat to +150°C/+250°C if necessary), remove cured residue mechanically and clean with acetone. Cure times At +25°C on steel: handling strength in 10–20 minutes, functional strength in 1–3 hours and full cure in 6–12 hours. Cure speed varies with gap, substrate and temperature. Specifications Chemistry Anaerobic methacrylate Colour Red (fluorescent under blue light) Viscosity (+25°C) 70–600 Pa·s Specific gravity (+25°C) Approx. 1.1 g/ml Maximum gap fill 0.50 mm Breakaway torque (ISO 10964) 15–25 N·m Prevailing torque (ISO 10964) 18–28 N·m Shear strength (ISO 4587) 8–13 N/mm² Tensile strength (ISO 6922) 7–10 N/mm² Impact strength (ASTM D-950) 4–7 kJ/m² Service temperature -55°C to +180°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Fully cured Loxeal 58-31 offers excellent resistance to motor oil and gearbox oil at +125°C through 1,000 hours, excellent-to-good resistance to hot 50% water/glycol mixtures, and moderate resistance to gasoline on prolonged exposure. Important notes Recommended for metal surfaces — seek technical advice before applying to non-metal parts. Uncured adhesive can damage coatings, some plastics and elastomers, and may cause delayed stress-cracking in certain thermoplastics. Store cool and dry at no more than +25°C; do not refill containers with used product. Safety Consult the Safety Data Sheet (SDS) before use. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$59.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the flange faces first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 58-14 Gasketing Anaerobic Adhesive 75ml Loxeal 58-14 is a medium-strength anaerobic gasketing adhesive that forms a flexible in-place gasket between flange faces, doing away with pre-cut solid gaskets. The highly thixotropic formula stays exactly where it is applied without migrating before or during cure, and the cured film seals dependably against gases, water, LPG, fuels, oils and many other chemicals across a service range of -55°C to +150°C. Why choose Loxeal 58-14? One liquid gasket replaces an inventory of pre-formed paper, cork and plastic gaskets Flexible cured film shrugs off shocks and vibration Thixotropic — stays put on vertical and horizontal flanges Fills gaps up to 0.50 mm and compensates for minor surface imperfections Assemblies can be dismantled later with standard workshop tools Typical applications Gasketing and sealing of flange joints on pumps, gearboxes, differential housings and similar close-fitting metal assemblies in automotive workshops, plant maintenance and general engineering. How to use Clean and degrease both flange faces (Loxeal Cleaner 10 recommended). Apply a continuous bead so the joint gap is completely filled. Assemble the parts and hold them in position while the adhesive cures. On passive metals or in cold conditions, accelerate the cure with Loxeal Activator 11. To dismantle, use normal tools (heating the parts to +150°C/+250°C helps if needed), remove cured residue mechanically and clean up with acetone. Cure times At +25°C on steel: handling strength in 15–30 minutes, functional strength in 3–6 hours and full cure in around 24 hours. Cure speed varies with gap size, substrate and temperature. Specifications Chemistry Anaerobic methacrylate Colour Orange Viscosity (+25°C) 28,000–100,000 mPa·s, highly thixotropic Specific gravity (+25°C) Approx. 1.1 g/ml Maximum gap fill 0.50 mm Shear strength (ISO 4587) 5–10 N/mm² Tensile strength (ISO 6922) 5–8 N/mm² Impact strength (ASTM D-950) 3–5 kJ/m² Service temperature -55°C to +150°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance Once fully cured, Loxeal 58-14 shows excellent resistance to motor oil and gearbox oil at +125°C out to 1,000 hours, and good long-term resistance to gasoline and to 50% water/glycol mixtures at +87°C. Important notes Formulated for metal surfaces — contact a technical adviser before use on non-metal parts. The liquid adhesive can attack coatings, some plastics and elastomers, and may induce delayed stress-cracking in certain thermoplastics. Store in a cool, dry place at no more than +25°C and never return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use and follow standard workshop hygiene practices. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$49.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the flange faces first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 59-10 Gasketing High Temperature Anaerobic Adhesive 75ml Loxeal 59-10 is a single-component, medium-strength anaerobic flange sealant with outstanding heat resistance up to +200°C. It cures at room temperature when confined without air between close-fitting metal surfaces, forming a durable in-place gasket that replaces pre-formed gaskets, allows wider machining tolerances and still permits dismantling with normal tools. The cured seal is highly resistant to vibration, heat, water, gases, LPG, oils, fuels and many chemicals. Why choose Loxeal 59-10? Service temperature from -55°C to +200°C — ideal for hot-running assemblies Replaces pre-formed gaskets and assures true metal-to-metal contact Fills gaps up to 0.50 mm, accommodating greater machining tolerances Highly resistant to vibration, oils, hydrocarbons and coolants Parts remain serviceable — dismantle with everyday workshop tools Typical applications Sealing flat, rigid flange joints on pumps, gearboxes, camshaft blocks and motor flanges — anywhere a heat-tolerant, vibration-proof formed-in-place gasket is required. How to use Clean and degrease the mating surfaces (Loxeal Cleaner 10 recommended). Apply enough product to fill the joint gap completely. Bring the parts together and leave undisturbed until cured. On passivated surfaces or at low temperature, use Loxeal Activator 11 to speed the cure. For disassembly, use normal tools (heat to +150°C/+250°C if needed), remove cured residue mechanically and clean with acetone. Cure times At +25°C on steel: handling strength in 15–30 minutes, functional strength in 3–6 hours and full cure in 6–12 hours. Cure speed depends on substrate, gap and temperature. Specifications Chemistry Anaerobic methacrylate Colour Red Viscosity (+25°C) 50–300 Pa·s Specific gravity (+25°C) Approx. 1.05 g/ml Maximum gap fill 0.50 mm Shear strength (ISO 4587) 5–10 N/mm² Tensile strength (ISO 6922) 6–8 N/mm² Impact strength (ASTM D-950) 3–5 kJ/m² Service temperature -55°C to +200°C Flash point > +100°C Shelf life 1 year at +25°C in original unopened packaging Chemical resistance After full cure, Loxeal 59-10 maintains excellent resistance to motor oil and gearbox oil at +125°C and to 50% water/glycol coolant at +87°C through 1,000 hours; resistance to gasoline is excellent initially, reducing with prolonged immersion. Important notes Recommended for metal surfaces — seek technical advice before use on non-metal parts. Liquid product may damage coated parts and elastomers, and contact with some thermoplastics can induce stress-cracking that is not immediately visible. Store in a cool, dry place at +25°C or below; never return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. The information above is provided as a general guide only, based on the manufacturer's technical data. Always confirm suitability for your specific application before use.
$54.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 85-86 Thread Sealant High Temperature Anaerobic Adhesive 50ml Loxeal 85-86 is a high strength anaerobic adhesive for locking and sealing threaded joints on all metals, in both free and forced matings. It maintains its sealing performance up to +200°C and offers high resistance to thermal shock, vibration, water, gas, oils, fuels, refrigerant fluids and many other chemicals – making it the choice for hot pipework, gas lines and demanding sealing jobs where standard sealants fall short. Why choose Loxeal 85-86? Seals and locks in one step with high mechanical strength Keeps sealing up to +200°C (service range -55°C to +200°C) Works on all metals, including free and press-fit assemblies Resists thermal shock, vibration, fuels, refrigerants and many chemicals Generous gap fill up to 0.30 mm on threads up to M56 / 2″ Green colour, fluorescent under blue light, for easy inspection Certified and approved Approved for gas-tight threaded joints to EN 751-1 (DIN-DVGW) WRAS approved for contact with wholesome (potable) water Compliant with the UBA (German Environment Agency) declaration for potable water use BAM certified as a sealant in the presence of gaseous oxygen up to 20 bar at +60°C Typical applications Sealing threaded joints on gas, steam, hot water and heating pipework Potable water fittings (observe the potable-water cure times below) Refrigeration, fuel and industrial fluid lines exposed to heat and vibration How to use Clean and degrease both threads with Loxeal Cleaner 10 and allow to dry. Apply a continuous bead circumferentially, 1–2 threads back from the leading edge, using enough product to give a complete seal. Assemble and tighten the joint, then wipe off any uncured excess. Allow to cure before pressurising. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 (this may reduce final strength). Cure times at +25°C Handling strength: 10–40 minutes Functional strength: 6–12 hours Full cure: 24–36 hours Before contact with potable water: allow 24 hours at +20°C for brass, copper and cast iron; 7 days for stainless steel and aluminium Specifications Chemistry Anaerobic methacrylate Colour Green (fluorescent under blue light) Viscosity (+25°C) 2,200–4,000 mPa·s Specific gravity (+25°C) 1.05 Max thread size / gap fill M56 / 2″ / 0.30 mm Shear strength (ISO 10123) 15–25 N/mm² Breakaway torque (ISO 10964) 25–35 N·m Prevailing torque (ISO 10964) 40–55 N·m Service temperature -55°C to +200°C Shelf life 1 year in original unopened packaging at up to +25°C Important notes Recommended for metal thread joints only – contact a technical service before use on other materials. Do not contaminate the adhesive with metal; cut the nozzle to the required bead size. The liquid product can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. High strength – for disassembly, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$39.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-03 Threadlocker Medium Strength Anaerobic Adhesive 10ml Loxeal 55-03 is a medium strength anaerobic threadlocker for nuts, bolts and studs of all types that may need to be dismantled later with standard hand tools. It tolerates minor oil contamination on the parts, so it keeps performing where threads are not perfectly clean. Once cured it resists vibration, corrosion, water, gas, oils, hydrocarbons and many other chemicals, and it holds its sealing properties from -55°C to +200°C (up to +250°C for short periods), with proven unscrewing resistance at +200°C. Why choose Loxeal 55-03? Medium strength – assemblies can be dismantled with normal tools when servicing is needed Tolerates light oil contamination on threads Locks and seals fasteners in one step, stopping loosening caused by vibration Wide service temperature range of -55°C to +200°C Blue colour, fluorescent under blue light, for easy inspection on the production line Seals the thread against ingress, helping prevent rust and fretting corrosion Certified and approved Approved as a gas-tight sealant for threaded fittings to European norm EN 751-1 (DVGW and Gaz de France) WRAS approved – suitable for use in contact with potable water Compliant with the UBA (German Environment Agency) declaration for potable water applications NSF registered in category S4 as acceptable for use as an adhesive in and around food processing areas Typical applications Securing nuts, bolts, studs and screws on machinery, vehicles and equipment subject to vibration Sealing threaded fittings on gas, water and compressed air lines Automotive, plumbing and general maintenance work where later disassembly must remain possible How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before putting the joint into service. On passive surfaces (e.g. stainless steel, plated parts) or in cold conditions, pre-treat with Loxeal Activator 11 to speed the cure (this may slightly reduce final strength). Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate resin Colour Blue (fluorescent under blue light) Viscosity (+25°C) 1,700–9,000 mPa·s, thixotropic Specific gravity (+25°C) 1.07 Max thread size / gap fill M36 / 0.25 mm Shear strength (ISO 10123) 9–13 N/mm² Breakaway torque (ISO 10964) 18–23 N·m Prevailing torque (ISO 10964) 9–16 N·m Service temperature -55°C to +200°C (+250°C short term) Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, ethanol and biodiesel, with good resistance to petrol, brake fluid, 50% water/glycol and acetone after 1,000 hours of exposure. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. Not approved for use with pure oxygen or oxygen-rich systems, and not suitable for sealing chlorine or other strong oxidising agents. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$14.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-14 Thread Sealant Anaerobic Adhesive 50ml Loxeal 55-14 is a medium strength anaerobic thread sealant for hydraulic and pneumatic threaded connectors up to 1-1/2″. It replaces PTFE tape and hemp for sealing against gases, water, LPG, hydrocarbons, oils and many other chemicals. A medium thixotropic consistency stops the sealant migrating out of the thread before or during cure, and the cured joint is highly resistant to heat, corrosion, shocks and vibration across a service range of -55°C to +150°C. Why choose Loxeal 55-14? General purpose sealer for hydraulic and pneumatic fittings up to 1-1/2″ Replaces PTFE tape and hemp – no shredding, no re-taping, no clogged valves Medium strength – joints can still be dismantled with normal tools Thixotropic formula stays on the thread instead of dripping or migrating Seals against gases, water, LPG, oils, hydrocarbons and many chemicals Resists shock, vibration and corrosion from -55°C to +150°C Typical applications Sealing threaded connectors on hydraulic and pneumatic systems Pipework carrying water, compressed air, LPG, oils and industrial fluids General plumbing and maintenance sealing of metal pipe threads How to use Clean and degrease both threads with Loxeal Cleaner 10 and allow to dry. Apply a bead of sealant around the male thread so the gap is completely filled. Assemble and tighten the connection. Allow to cure before pressurising. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to speed the cure. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 5–10 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Red (fluorescent under blue light) Viscosity (+25°C) 2,500–12,000 mPa·s, thixotropic Specific gravity (+25°C) 1.05 Max thread size / gap fill M56 / 2″ / 0.30 mm Shear strength (ISO 10123) 8–12 N/mm² Breakaway torque (ISO 10964) 12–18 N·m Prevailing torque (ISO 10964) 20–30 N·m Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Important notes Formulated for metal threads only – contact a technical service before use on other materials. The liquid sealant can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$34.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 53-11 Retaining Compound Anaerobic Adhesive 50ml Loxeal 53-11 is a medium strength anaerobic retaining compound for fixing bearings, liners, bushes, keys and splines into housings and onto shafts. It fills the space between cylindrical parts to give 100% surface contact, boosting load-carrying capacity while still allowing disassembly with standard workshop methods. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals across a service range of -55°C to +150°C. Why choose Loxeal 53-11? General purpose retainer for bearings, bushes, liners, keys and splines Medium strength – parts remain serviceable and can be dismantled Fills the joint completely, preventing fretting corrosion between mating parts Increases load transmission compared with a mechanical fit alone Low viscosity wicks into close-fitting cylindrical assemblies Resists vibration, oils, fuels and many chemicals from -55°C to +150°C Typical applications Retaining bearings and bushes in housings and on shafts Securing cylinder liners, keys, splines and sleeves Workshop repairs to restore security in worn cylindrical fits How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts, seating them fully, and hold in position for the cure time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Yellow (fluorescent under blue light) Viscosity (+25°C) 400–650 mPa·s Specific gravity (+25°C) 1.05 Max thread size / gap fill M20 / 0.12 mm Shear strength (ISO 10123) 8–12 N/mm² Breakaway torque (ISO 10964) 11–20 N·m Prevailing torque (ISO 10964) 15–25 N·m Impact strength (ASTM D-950) 1–5 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to motor oil and gearbox oil at +125°C, petrol and brake fluid at +25°C (out to 5,000 hours), with good resistance to 50% water/glycol at +87°C. Important notes Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, use normal tools; if needed, heat parts to +150°C/+250°C, remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$39.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease both parts first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 82-21 Retaining Compound Fast Cure Anaerobic Adhesive 50ml Loxeal 82-21 is a fast curing, high strength anaerobic retaining compound for close-fitting cylindrical parts – shafts, bushes, pulleys and rotors. Its low viscosity flows into precise fits, reaching handling strength in as little as 5–10 minutes, and cures to a tough bond with 17–22 N/mm² shear strength. The cured adhesive is highly resistant to heat, corrosion, vibration, water, gases, oils and hydrocarbons across a service range of -55°C to +150°C. Why choose Loxeal 82-21? Fast fixture – handling strength in 5–10 minutes keeps jobs moving High strength bond for permanent retention of close-fitted parts Low viscosity penetrates precise cylindrical fits (up to 0.10 mm gap) High impact strength of 11–15 kJ/m² for parts under shock loading Fills the joint completely, preventing fretting corrosion Resists vibration and many chemicals from -55°C to +150°C Typical applications Bonding pulleys, gears and rotors onto shafts Retaining bushes and bearings in precision housings Production assembly where fast fixture times are needed How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply the adhesive so the bond gap is completely filled. Assemble the parts promptly, seating them fully, and hold for the fixture time. Allow to cure before loading. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 5–10 minutes Functional strength: 1–3 hours Full cure: 3–6 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green Viscosity (+25°C) 120–180 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M12 / 0.10 mm Shear strength (ISO 10123) 17–22 N/mm² Breakaway torque (ISO 10964) 24–35 N·m Prevailing torque (ISO 10964) 50–60 N·m Impact strength (ASTM D-950) 11–15 kJ/m² Service temperature -55°C to +150°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to refrigerants (Freon) at +25°C, excellent resistance to petrol out to 500 hours, and moderate resistance to motor and gearbox oils at +40°C over extended exposure. Important notes High strength – intended as a permanent retaining bond. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$44.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 83-54 Threadlocker High Strength Anaerobic Adhesive 50ml Loxeal 83-54 is a high strength anaerobic threadlocker for permanently locking and sealing studs, nuts, bolts and threaded fasteners that are not intended to be dismantled. It can be used on all metals, in both free and interference fits, and delivers high unscrewing resistance with temperature performance up to +200°C. The cured adhesive stands up to heat, corrosion, vibration, water, gases, oils, hydrocarbons and many chemicals, making it a direct alternative to other high-strength studlocks such as Loctite 263. Why choose Loxeal 83-54? High strength, permanent locking for fasteners that must not come loose Strong prevailing torque of 50–65 N·m keeps holding even after the initial break Service temperature from -55°C to +200°C Suitable for all metals, in free or forced (press-fit) matings Green colour, fluorescent under blue light, for easy quality inspection Seals the thread, protecting against corrosion and leakage Typical applications Permanent locking of studs into engine blocks, housings and castings Heavy machinery, driveline and suspension fasteners exposed to strong vibration Fasteners on pumps, compressors and equipment where loosening would be a safety risk How to use Clean and degrease both parts with Loxeal Cleaner 10 and allow to dry. Apply enough adhesive to completely fill the engaged threads. Assemble and tighten the fastener to the required torque. Allow to cure before loading the joint. On passive surfaces or in cold conditions, pre-treat with Loxeal Activator 11 to accelerate curing. Cure times at +25°C Handling strength: 10–20 minutes Functional strength: 1–3 hours Full cure: 5–10 hours (maximum properties develop over 24–36 hours) Specifications Chemistry Anaerobic methacrylate Colour Green (fluorescent under blue light) Viscosity (+25°C) 450–650 mPa·s Specific gravity (+25°C) 1.1 Max thread size / gap fill M20 / 0.15 mm Shear strength (ISO 10123) 15–20 N/mm² Breakaway torque (ISO 10964) 25–35 N·m Prevailing torque (ISO 10964) 50–65 N·m Service temperature -55°C to +200°C Shelf life 1 year in original unopened packaging at up to +25°C Chemical resistance Manufacturer ageing tests show excellent long-term resistance to petrol and brake fluid at +25°C, good resistance to 50% water/glycol at +87°C, and good short-term resistance to motor and gearbox oils at +125°C (moderate on extended exposure). Important notes Designed as a permanent locking product – routine disassembly is not intended. Formulated for metal substrates only – contact a technical service before use on other materials. The liquid adhesive can damage coatings, some plastics and elastomers, and may cause stress cracking in some thermoplastics. To disassemble, heat parts to +150°C/+250°C, use normal tools, then remove cured residue mechanically and clean with acetone. Store in a cool, dry place at no more than +25°C and do not return used product to the container. Safety Consult the Safety Data Sheet (SDS) before use. For professional and industrial use. This information is provided as a general guide only, based on the manufacturer's technical data sheet. Always verify suitability for your specific application and consult the current TDS and SDS before use.
$44.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 55-03 Medium Strength Anaerobic Threadlocker Loxeal 55-03 is a medium strength anaerobic threadlocker for nuts and bolts of all types that may need to be dismantled later. It tolerates minor oil contamination on parts, so it performs even on as-received fasteners, and it holds its locking and sealing properties from -55°C to +200°C (up to +250°C for short periods). The direct alternative to Loctite 243. Why choose Loxeal 55-03 Oil tolerant: cures reliably on lightly oiled threads without extensive cleaning. High temperature: proven unscrewing resistance at +200°C. Serviceable strength: locks firmly against vibration yet can be dismantled with hand tools. Wide chemical compatibility: resists water, gas, oils, gasoline, brake fluid, ethanol, biodiesel and many chemicals. Blue colour, fluorescent under blue light for easy inspection. Certified and approved Gas: approved as gas-tight sealant for threaded fittings to EN 751-1 (DVGW and Gaz de France). Potable water: WRAS approved and compliant with the German UBA declaration for drinking water use. Food areas: NSF registered category S4 for use as an adhesive in and around food processing areas. Typical applications Locking machine bolts, pump housings, gearbox fasteners and automotive nuts and bolts subject to vibration. Threaded fittings in gas and potable water systems where certified products are required. Maintenance work on equipment where fasteners arrive lightly oiled. How to use Clean and degrease parts where practical (Loxeal Cleaner 10 recommended); minor oil films are tolerated. Apply enough product to completely fill the engaged threads. Assemble the parts and hold for the curing time. On passive surfaces or in cold conditions, Loxeal Activator 11 speeds curing (may slightly reduce final strength). Cure times at +25°C Handling: 10 to 20 minutes Functional: 1 to 3 hours Full cure: 24 to 36 hours depending on substrate, gap and temperature Specifications Chemistry Anaerobic methacrylate resin Colour Blue (fluorescent under blue light) Strength grade Medium (dismantlable) Viscosity at +25°C 1,700 to 9,000 mPa·s, thixotropic Specific gravity Approx. 1.07 g/ml Friction coefficient Approx. 0.10 Max thread / gap filling M36 / 0.25 mm Shear strength 9 to 13 N/mm² (ISO 10123) Breakaway torque 18 to 23 N·m (ISO 10964) Prevailing torque 9 to 16 N·m (ISO 10964) Service temperature -55°C to +200°C (+250°C short term) Approvals EN 751-1 (DVGW, Gaz de France), WRAS, UBA, NSF S4 Shelf life 1 year in unopened packaging at up to +25°C Chemical resistance Excellent long-term resistance to motor oil and gearbox oil at +125°C, ethanol and biodiesel at room temperature; excellent to good resistance to gasoline, brake fluid and 50 percent water glycol. Important notes For metal fasteners. Liquid product can damage coatings, some plastics and elastomers; stress cracking may develop with some thermoplastics. Not approved for pure oxygen or oxygen-rich systems, and not suitable as a sealant for chlorine or other strong oxidising agents. For disassembly use normal tools; if needed heat parts to +150°C to +250°C, remove cured residue mechanically and clean with acetone. Store cool and dry at or below +25°C. Do not return used product to the bottle. Safety Consult the Safety Data Sheet before use. For professional and industrial use. Follow all handling instructions on the product label. All technical information is provided as a guide only. Always verify suitability with your specific materials and operating conditions before use.
$39.95
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 24-18 Low Strength Anaerobic Threadlocker Loxeal 24-18 is a low strength anaerobic threadlocker for nuts, bolts and screws of all types that need to be easily dismantled later with ordinary hand tools. It locks fasteners against loosening from vibration and thermal cycling while staying serviceable, making it the go-to grade for small screws, adjustment fasteners and parts that see regular maintenance. Why choose Loxeal 24-18 Easy disassembly: low breakaway torque means fasteners come apart with standard tools, no heat needed in most cases. Anti-vibration: prevents self-loosening caused by vibration, shock and temperature changes. Wide chemical compatibility: resists water, gases, oils, gasoline, diesel and many chemicals. Gas approved: DVGW approved as a gas-tight sealant for threaded fittings to European norm EN 751-1. Service temperature from -55°C to +150°C. Purple colour, fluorescent under blue light for easy inspection. Typical applications Locking small screws, grub screws, calibration and adjustment fasteners that require frequent servicing. General automotive, machinery and DIY threadlocking where easy removal matters. Thread sealing of metal fittings where a low strength, dismantlable seal is acceptable. How to use Clean and degrease threads (Loxeal Cleaner 10 recommended). Apply enough product to fill the engaged threads. Assemble the parts and tighten as normal. Allow to cure before putting into service. On passivated surfaces or in cold conditions, use Loxeal Activator 11 to speed curing. Cure times at +25°C Handling: 15 to 30 minutes Functional: 1 to 3 hours Full cure: up to 24 to 36 hours depending on substrate, gap and temperature Specifications Chemistry Anaerobic methacrylate Colour Purple (fluorescent under blue light) Strength grade Low (easy to dismantle) Viscosity at +25°C 800 to 1,400 mPa·s Specific gravity Approx. 1.05 g/ml Max thread / gap filling M24 / 0.20 mm Shear strength 3 to 5 N/mm² (ISO 10123) Breakaway torque 5 to 8 N·m (ISO 10964) Prevailing torque 2 to 5 N·m (ISO 10964) Service temperature -55°C to +150°C Approvals DVGW gas-tight sealant, EN 751-1 Shelf life 1 year in unopened packaging at up to +25°C Chemical resistance Excellent resistance to gasoline and brake fluid at room temperature; excellent to good resistance to motor oil, gearbox oil and diesel at +125°C, and to 50 percent water glycol at +87°C. Important notes For metal fasteners. Liquid product can attack some coatings, plastics and elastomers; contact with some thermoplastics may cause stress cracking. Pre-test if unsure. For disassembly use normal tools; if needed heat parts to +150°C to +250°C, remove cured residue mechanically and clean with acetone. Store cool and dry at or below +25°C. Do not return used product to the bottle. Safety Consult the Safety Data Sheet before use. Follow all handling instructions on the product label. All technical information is provided as a guide only. Always verify suitability with your specific materials and operating conditions before use.
$39.95
Red, permanent Thread Locker prevents loosening by filling in the inner spaces in threaded metal parts to form a tough solid assembly. Pacer Technology Super Glue Red Threadlocker (15191) is a high strength premium grade product used to permanently lock or seal metal threaded components or for metal fasteners up to 1” in diameter. Also prevents loosening due to high vibration. Appearance – red liquid with mild odour. Use Instructions: For best results, parts should be clean and dry. Apply a bead around the part to be bonded & assemble with a twisting motion to spread adhesive. Allow curing 24 hours for maximum strength. The excess adhesive on the outside of parts will not cure and can be removed with a solvent-soaked cloth. Storage and shelf life: Recap for storage. A one-year shelf life can be expected. CAUTION: IRRITATING TO EYES AND SKIN. Contains methacrylate esters and cumene hydroperoxide. Avoid contact with eyes and skin. May cause skin dermatitis on prolonged contact with sensitive individuals. In case of eye contact, rinse immediately with plenty of water and seek medical advice. Wash skin thoroughly with soap and water after use. Seek medical advice if skin irritation persists. KEEP OUT OF REACH OF CHILDREN.
$9.95
Blue, removable Thread Locker prevents threaded metal fasteners, nuts, bolts, and screws from loosening. Thread Locker is an advanced anaerobic adhesive. Pacer Technology Super Glue Blue Threadlocker (15190) is a premium grade product used to lock or seal metal threaded components or for metal fasteners up to ¾” in diameter. This product prevents loosening due to high vibration. Parts can be disassembled with simple hand tools. PROPERTIES: Appearance – blue liquid with mild odor. USE INSTRUCTIONS: For best results, parts should be clean and dry. Apply a bead around the part to be bonded & assemble with a twisting motion to spread adhesive. Allow to cure 24 hours for maximum strength. Excess adhesive on outside of parts will not cure and can be removed with a solvent-soaked cloth. STORAGE AND SHELF LIFE Recap for storage. A one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS CAUTION: IRRITATING TO EYES AND SKIN. Contains methacrylate esters and cumene hydroperoxide. Avoid contact with eyes and skin. May cause skin dermatitis on prolonged contact with sensitive individuals. In case of eye contact, rinse immediately with plenty of water and seek medical advice. Wash skin thoroughly with soap and water after use. Seek medical advice if skin irritation persists.KEEP OUT OF REACH OF CHILDREN.
$12.50
LOCTITE® 249 is a blue, dimethacrylate ester acrylic film thread locker. It is supplied in a low tack film to provide a convenient and easy to use package, especially where a liquid product may be too fluid to stay on a part or be difficult to apply. This product can be used for immediate assembly or days later and provide consistent strength on a variety of metal substrates. Dimethacrylate ester acrylic film threadlocker. It is supplied in a low tack film to provide a convenient and easy to use package. Designed for the locking and sealing of threaded fasteners which require normal disassembly with standard hand tools Supplied in a low tack film to provide a convenient and easy to use package Can be used for immediate assembly or days later Provides consistent strength on a variety of metal substrates Technical Information Color Blue Cure Type Activator Cure, Anaerobic Cure Full Cure Temperature 77 °F Key Characteristics No Mix Number of Components 1 Part Physical Form Film Storage Temperature 46 - 69 °F Technology Acrylic Temperature -65 - 300 °F Thread Size (Maximum) R3/4" Torque Break on M10 Steel 74 in./lb. Torque Prevail on M10 Steel 47 in./lb. Viscosity 8700 mPa.s (cP) Brookfield Viscosity Temperature 25 °C
$16.08
LOCTITE 660 is a high strength retaining compound with good gap filling properties, ideal for repairing worn-out seats, keys, splines, bearings or tapers without remachining. LOCTITE® 660 is designed for the bonding of cylindrical fitting parts, particularly where bond gaps occurs without the need for remachining. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. LOCTITE 660 exhibits excellent gap cure characteristics and is also suitable for retaining shims. Ideal for repairing worn parts without remachining Enables re-use of worn bearing seats, keys, splines or tapers Suitable for retaining shims P1 NSF Reg. No.: 123704 Technical Information Agency Approvals / Specifications NSF P1 Color Silver Diametrical Clearance (Maximum) Unit mm Fixture Time 15 min. Fixture Time Temperature 15 °C Gap Fill 0.5 mm Key Characteristics Thixotropic Substrates Metal: Steel
$10.59
Retaining Compound - medium strength. If disassembly is required. Ideal for parts that need subsequent dismantling. LOCTITE® 641 is designed for the bonding of cylindrical fitting parts, particularly where disassembly is required for servicing operations. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings Technical Information Colour Yellow Diametrical Clearance (Maximum) 0.1 mm Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.1 mm Shear Strength Unit, Steel psi Shear Strength, Steel 1700 Specific Gravity 1.07 g/l Specific Gravity Temperature 25 °C Substrates Metal: Steel Temperature -65 - 300 °F Viscosity 525 - 1950 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$22.40
High strength methacrylate ester acrylic retaining compound designed for the bonding of cylindrical fitting parts. LOCTITE® 609 is a green, high strength methacrylate ester acrylic retaining compound designed for the bonding of cylindrical fitting parts. The product cures in the absence of air between close-fitting metal surfaces. Typical applications include rotor to shafts in fractional and subfractional horsepower motors. Locks bushings and sleeves in housings on shafts. Augments press fits. Low viscosity Prevents loosening and leakage from shock and vibration Augments press fits Tested to the lot requirements of Military Specification Mil-R-46082B (this is a regional approval) Technical Information Agency Approvals / Specifications ASTM D5363, CFIA Listed, MIL-R-46082B for existing designs Application Method Pressure Applications For Close Fitting Parts, Retaining Colour Green Cure Type Anaerobic Cure Diametrical Clearance (Maximum) Unit in. Fixture Time 10 min. Fixture Time Temperature 10 °C Full Cure Temperature 22 °C Full Cure Time 24 hr. Gap Fill 0.006 in. Key Characteristics Fluorescent, Strength: High Strength, Viscosity: Low Viscosity Number of Components 1 Part Physical Form Liquid Shear Strength Unit, Steel psi Shear Strength, Steel 2300 Specific Gravity 1.1 g/l Specific Gravity Temperature 25 °C Substrates Metal Technology Acrylic Temperature -65 - 300 °F Viscosity 125 mPa.s (cP) Brookfield Viscosity (#7sp/20/rpm) 125 mPa.s (cP) Brookfield Viscosity Temperature 25 °C
$12.12
Thread Sealant - medium strength. For fine threads in hydraulic, pneumatic and general fittings. Fast curing. LOCTITE® 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part. Ideal for fine threads as used in hydraulic, pneumatic & general fittings Suitable for metal threads only Instant low-pressure seal Resistant to fuel, oil, coolants and hydraulic fluids Locks connection against vibration loosening PRODUCT DESCRIPTION LOCTITE® 542 provides the following product characteristics: Technology Acrylic Chemical Type Dimethacrylate ester Appearance (uncured) Brown liquidLMS Components One component - requires no mixing Viscosity Low Cure Anaerobic Secondary Cure Activator Application Thread sealing Strength Medium Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry. 2. If the material is an inactive metal or the cure speed is too slow, spray all threads with and allow to dry. 3. Apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also. 4. Using compliant practices, assemble and wrench tighten fittings in accordance with manufacturers recommendations. 5. Properly tightened fittings will seal instantly to moderate pressures. For maximum pressure resistance and solvent resistance allow the product to cure a minimum of 24 hours. For Disassembly 1. Remove with standard hand tools. 2. Where hand tools do not work because of excessive engagement length or large diameters (over 1"), apply localized heat to approximately 250 °C. Disassemble while hot. For Cleanup 1. Cured product can be removed with a combination of soaking in a Loctite solvent and mechanical abrasion such as a wire brush.
$12.26
LOCTITE 518 is a medium-strength, general purpose gasketing product with excellent contamination tolerance. Ideal for use on casted iron, steel and aluminum flanges. LOCTITE® 518 cures when confined in the absence of air between close-fitting metal surfaces. It is an anaerobic gasketing material designed for use on rigid iron, aluminum, and steel flanged mating surfaces. LOCTITE 518 fills gaps up to 0.25mm and forms a flexible, chemical-resistant seal that will not tear or decay. Parts disassemble easily, even after extended service. Typical applications include sealing close-fitting joints between rigid metal faces and flanges. It is also used as a formed-in-place gasket on rigid flanged connections, e.g. transmissions and motor housings. Semi-flexible, medium-strength anaerobic flange gasket Easy to automate Reduces process costs – eliminates manual assembly of conventional gaskets NSF P1 Reg. No. 123758 For active and inactive rigid metal flanges Cures through minor surface contamination Adapts to flange surface irregularities and gaps up to 0.25 mm Gel-type consistency Seals instantly against low pressure Reduces inventory costs – no need for large inventory of cut gaskets Resists high pressure when fully cured No compression set or misaligned gaskets Technical Information Applications Rigid Assembly Gasketing Colour Red Cure Schedule Temperature (Step 1) 200 Cure Schedule Temperature Unit (Step 1) °C Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.3 mm Shelf Life Temperature -40 °C Specific Gravity 1.1 g/l Specific Gravity Temperature 25 °C Substrates Metal: Aluminum Temperature -65 - 300 °F Tensile Shear Strength 7.5 N/mm² Viscosity 500000 - 1000000 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$9.95
LOCTITE 290 is a medium/high strength, wicking grade threadlocking adhesive that is ideal for locking preassembled fasteners. LOCTITE® 290 is a liquid medium/high-strength threadlocker designed for the locking and sealing of threaded fasteners. Because of its low viscosity and capillary action, the product wicks between engaged threads and eliminates the need for disassembly prior to application. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. The product can also fill porosities in welds, castings and powdered metal parts. Ideal for locking preassembled fasteners, e.g. instrumentation fasteners, electrical connectors and set screws Works on metal only Proven to be tolerant of minor contamination due to industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids Requires heat for disassembly
$12.48
Hold It Australia T77 STUDLOCK High Strength for Bolts 25mm and Above - 50ml Description: HOLDIT AUSTRALIA T77 Studlock large diameter high strength threadlocker is a red, general purpose adhesive for permanent threaded assemblies. It effectively locks fasteners 1 and larger in diameter, providing a seal against leakage and corrosion while resisting attacks from lubricants and industrial liquids and gases. Applications Ideal for eliminating double nutting/welding in critical assemblies. T77 allows for reduced casting thickness and prevents cracked castings from interference fit stresses. Suitable for larger diameter studs with coarse threads and can be used to reclaim worn stud holes. Primers are recommended for large gaps and poorly fitting parts. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Hold It Australia T72 STUDLOCK High Temp High Strength for Bolts 25mm and Above - 50ml Description: HOLDIT AUSTRALIA T72 Studlock is a High Strength-High Temperature Threadlocker. This red, single component, anaerobic adhesive is ideal for joining threaded parts exposed to operating temperatures up to 232°C. Its enhanced chemistry allows superior performance at temperatures significantly higher than other thread locking products. Applications T72 is perfect for high-temperature locking and sealing of studs, nuts, screws, bolts, and fittings. It effectively locks and seals parts against leakage, contamination, and corrosion, particularly suitable for larger diameter, coarse-threaded parts. Recommended for components not requiring routine maintenance, as disassembly can be challenging and may require heat. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Hold It Australia T71 THREADLOCK High Strength, Low Viscosity - 50ml Description: HOLDIT AUSTRALIA T71 Threadlock is a high-strength, anaerobic thread locking compound. T71 is developed for the permanent locking of threaded fasteners and performs well on aluminium, steel, plated fasteners, stainless steel, and special alloy parts. It boasts good temperature stability and solvent resistance. Applications T71 is designed to lock and seal large fasteners, especially in applications where shock and vibration might cause loosening. Its high strength ensures a reliable lock in demanding environments. Instructions for Use Clean all surfaces with a cleaning solvent and let them dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or to the internal threads of a blind hole. Assemble the components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Hold It Australia STUDLOCK Mid Strength Lubricated for Torque Assembly - 50ml Description: HOLDIT AUSTRALIA T62 Lubricated Thread Locker is a medium strength, anaerobic thread locking compound, perfect for permanent locking of threaded fasteners. T62 is effective on aluminium, steel, plated, stainless steel, and special alloy parts. It is characterized by its good temperature and solvent resistance. Applications Designed for locking and sealing large fasteners (1 and larger), T62 is ideal for applications where shock and vibration may cause fasteners to loosen, ensuring a stable and permanent lock. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry for optimal adhesion. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying any load. Active & Inactive Metal Table Consult the Active and Inactive Metal Table for specific application guidance on different metal types.
$34.86
Hold It Australia T43 NUTLOCK Medium Strength (Oil Tolerant) - 50ml Description: HOLDIT AUSTRALIA T43 Nutlock is an oil tolerant, medium viscosity, Thixotropic, anaerobic thread locking adhesive suitable for all types of metal threaded fasteners. The cured adhesive offers controlled medium strength, excellent temperature, and solvent resistance, particularly against water and nonpolar solvents. It rapidly cures on plated, oily metal surfaces or inactive surfaces. Applications Ideal for replacing lock washers and plastic inserts, NUTLOCK locks machine tool access bolts, studs, hydraulic system bolts, gear box bolts/drive shaft, bearing cover cap screws, counter sunk screws, conveyor roller bolts, and is suitable for construction equipment. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry for optimal bonding. If metal is inactive or cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Please consult the Active and Inactive Metal Table for specific application guidance.
$34.86
Hold It Australia T22 SCREWLOCK Low Strength for Easy Disassembly - 50ml Description: HOLDIT AUSTRALIA T22 Screwlock is a low strength, anaerobic thread locking compound, ideal for locking threaded fasteners that require disassembly with standard hand tools. It performs excellently on aluminium, steel, plated, stainless steel, and special alloy parts. T22 is characterized by its good temperature and solvent resistance. Applications T22 is specifically formulated to lock and seal small screws (less than ¼), including set screws with long engagement lengths. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry for optimal results. If the metal is inactive or the cure speed is too slow, apply HOLDIT AUSTRALIA AA471 Activator or HOLDIT AUSTRALIA AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow to fully cure before applying load. Properties of Uncured Material Chemical Type: Anaerobic Colour: Purple Toxicity: Low Solid Content: 100% Viscosity @ 25°C, cPs: 900-1,500 cps Specific Gravity: 1.05 Shelf Life: 24 months Performance of Cured Material Fixture Speed: 15-20 Min @ 22°C Full Cure: 24 Hours @ 22°C Temperature Range: -50°C to 150°C Product Conformity: MIL-S-46163A, ASTM D-5363, NSF Technical Datasheet The cure speed of HOLDIT AUSTRALIA T22 is dependent on temperature and substrate. The product shows a breakaway strength of 1Nm 9Nm on 3/8 plain steel nut & bolt after 1 hour and 5Nm 11Nm after 24 hours. On a 3/8 zinc nut & bolt, the strength is 1Nm 4Nm after 24 hours. Environmental and Fluid Resistance Heat Age: 100% retention in Engine oil @ 150°C Brake Fluid @ 150°C: 85% retention ATF @ 150°C: 85% retention 50/50 water/ethylene glycol @ 120°C: 80% retention Water @ 100°C: 80% retention Gasoline @ 25°C: 95% retention Diesel Fuel @ 25°C: 100% retention Ethyl Alcohol @ 25°C: 90% retention Active & Inactive Metal Table Category Cure Speed Metals Super Active Very Fast Cure Brass, Copper, Magnesium Active Fast Cure Iron, Steel, Nickel, Aluminium Inactive Slow Cure Stainless Steel, Titanium, Zinc Passive Primer Necessary Anodized Aluminium, Galvanised Steel, Ceramics, Glass, Plastics, Painted Finishes
$34.86
Threadlockers, retaining compounds and gasket makers that cure in the absence of air on metal parts. Ideal for fasteners, bearings and flanges. Choose low/medium/high strength as needed and follow cleaning/priming steps for best results. Use filters to refine by strength, temperature rating and application type. Always review the product page and TDS/SDS.
