Note :If you are working on a wooden floor, you will need to use the Fix-A-Floor Polyurethane For Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive " Now Patented", is an Extra Strength Bonding Adhesive customized for the specific use of Re-Bonding loose and hollow tile, marble & stone without the expense and mess of removing or replacing them. Fix-A-Floor is a simple do it yourself repair that is fast, easy and affordable not to mention fun and quite rewarding to anyone who can operate a drill, caulking gun and mix up a small batch of grout. Works on all sub-floor materials. Just Drill & Fill! The TipThe Tip of the 10.1 oz. Fix-A-Floor tube has been specially designed and engineered with a pre-drilled 1/8" hole for the sole purpose of filling drilled holes in loose & hollow tile, marble & stone floors. The Tip is extra firm and allows for a strong seal which promotes good flow and complete coverage. The 1/8" pre-drilled tip allows for use in narrow grout line applications or wider. It has marked lines showing clear cut points of 3/16", 1/4" or any other size you may need. The AdhesiveFix-A-Floor Repair Adhesive is Strong & Flexible with elastomeric bonding properties to eliminate any future problems due to foundation settlement, expansion & contraction of the sub floor as well as poor original installation... Used by professionals for years, now YOU can fix your loose & hollow, squeaky floors with Fix-A-Floor!!! Fix-A-Floor is Non-Toxic, Non-Flammable & Eco-Friendly! Large problem area or small problem areas are no problem with Fix-A-Floor! Guaranteed for the life of your floor! Just Drill & Fill! FAQs Q: Will Fix-A-Floor work if I have heated floors?A: Yes! We have customers using Fix-A-Floor with heated floor elements all the time with no problems. Keep heating element off before, during & for 48 hrs. after applying. Q: Some of my grout is missing or completely gone? How can I use Fix-A-Floor?A: If bits and pieces of grout are missing here and there around the problem area, just go ahead and Drill & Fill, the adhesive will actually help to re-bond the bits that are cracking and loose. If your grout is completely gone we recommend lightly re-grouting the area allow to dry and then Drill & Fill! Q: Can I use Fix-A-Floor to fix my entire floor or just a small area?A: Fix-A-Floor works great on all size problem areas from 1 tile to the whole entire floor! Works on all types of Tile, Marble & Stone floors too! Q: Can I use Fix-A-Floor outside on my patio or deck?A: Yes! Fix-A-Floor works beautifully on interior and exterior applications. Q: Can I use Fix-A-Floor in my shower or Pool?A: No! Fix-A-Floor is not recommended for areas with exposed to excessive moisture. Q: Is Fix-A-Floor Safe?A: Yes! Fix-A-Floor is a non-toxic, non-flammable and Eco-Friendly water-based adhesive. Q: Can I use Fix-A-Floor to re-glue a tile that is off the floor?A: Yes, simply squeeze Fix-A-Floor onto the floor where the tile was and press the tile back down onto the floor, place weight and allow to dry for 24 hrs. Tile will be rebonded! Q: Do I have to place buckets of water on my floor after I Drill & Fill?A: It is recommended you place some kind of weight on the area to aid in curing and to be sure no excess adhesive is trapped under your floor before regrouting. It is not mandatory. Q: What if I don’t see the adhesive coming up out of the other holes?A: While filling Fix-A-Floor will usually come up and out of the other drilled holes. If this does not happen move to another hole and continue to fill, the adhesive is still travelling under the floor. If you see the adhesive coming back up out of the hole you are filling, be sure you are NOT pressing the tip of the tube down onto the subfloor. Q: What if the adhesive is clumpy or not flowing out of the tube properly?A: The adhesive in the tube has frozen either in transit during the cold winter months this can happen. Simply contact us for a replacement.
$34.95
Say Goodbye to Stubborn, Sticky Messes! Tired of wrestling with stubborn price tags that tear and leave a papery, sticky mess? Frustrated by gummy residue left behind by tape on new appliances or furniture? We've all been there, risking our fingernails and damaging surfaces trying to scrape and scrub away unwanted adhesives. It’s time to stop the struggle. Introducing Un-Du® Adhesive Remover, the ultimate solution from Glues Australia that works like magic. This isn't just another solvent; it's a revolutionary removal system. Unlike harsh chemicals that dissolve glue and ruin your items, the Un-Du® formula cleverly works by temporarily neutralizing the adhesive. A few drops are all it takes to seep under the label or sticker, breaking the bond with the surface. Simply lift it off cleanly and effortlessly with the handy included scraper tool. The best part? Once the fast-evaporating Un-Du® formula disappears, the stickiness on the sticker returns, allowing you to reuse it somewhere else! It’s the perfect tool for repositioning labels, photos, and more. An Essential Tool for Every Australian Home From the kitchen to the garage, you'll find hundreds of uses for Un-Du®. It’s the one tool that’s more versatile than duct tape, designed to solve all those sticky problems that pop up in daily life. Keep a bottle handy and you'll always be prepared. Gift Giving Made Easy: Effortlessly removes price stickers from delicate gifts like crystal vases, books, and photo frames without leaving a trace. Clean Up Your Car: Finally get rid of that old bumper sticker from your ute or the remnants of a parking permit on your windscreen without damaging the paint or glass. Appliance & Furniture Rescue: Safely removes warranty stickers, energy rating labels, and masking tape from new fridges, TVs, and fine wood furniture. Household Accidents: Lifts chewing gum from carpet, tar from floors, and crayon marks from walls with remarkable ease. The Ultimate Office & Warehouse Productivity Hack Streamline your workflow and maintain a clean, professional workspace. Un-Du® is an indispensable asset for any office, mailroom, or warehouse environment, saving you time, money, and frustration. Package & Mail Management: Open self-sealing envelopes and padded mailers without tearing them, perfect for retrieving contents or reusing packaging. File & Asset Organisation: Easily remove and replace labels on files, shelves, computer disks, and office equipment without leaving a sticky, dirt-collecting residue. Mistake Correction: Quickly lifts correction fluid (White Out) from documents without smudging or tearing the paper. Workspace Maintenance: Removes old tape marks from desks, partitions, and windows, keeping your office looking pristine. A Must-Have for Crafters and Memory Keepers Your precious memories and delicate projects deserve the best care. The Un-Du® formula is completely acid-free and photo-safe, making it the trusted choice for hobbyists, scrapbookers, and archivists who demand perfection and preservation. Scrapbooking Perfection: Safely lift and reposition photos in albums and scrapbooks without causing fading, yellowing, or damage. Model Making: Remove masking tape from delicate models without lifting paint or leaving residue. Paper Crafts: Adjust stickers and embellishments on acid-free and lignin-free papers with total confidence. Stop struggling and start un-sticking the clean, simple, and safe way. Add Un-Du® Adhesive & Sticker Remover to your cart today and discover a world free from sticky situations! Product Specifications Brand: Un-Du® Product Name: Adhesive & Sticker Remover Formula: Acid-Free, Photo-Safe, Quick-Evaporating Solvent Key Feature: Temporarily neutralizes adhesives, allowing for the reuse of most stickers and labels after evaporation. Residue: Leaves no oily, greasy, or sticky residue behind. Tool: Comes with an attached, non-scratching, integrated scraper tool for easy lifting. Common Applications: Sticker & Label Removal Tape & Decal Removal Price Tag Removal Gum & Tar Cleaning Correction Fluid (White Out) Lifting Opening Sealed Envelopes Safe For Use On Surfaces Including: Glass & Plastics Fine Wood Furniture Metals Carpets & Upholstery Delicate Fabrics Photos Acid & Lignin-Free Papers Painted Surfaces & Wallpaper And much more!
$19.00
Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$23.00
*NEW* Fix-A-Floor Polyurethane Wood Floor Repair Adhesive is an Extra Strength, Super Blend Formula! Created specifically for Re-Bonding those Loose & Hollow, Squeaky, Popping, Bouncy Wood Floors. No need to remove or replace, Just Drill & Fill! The narrow tip allows for the smallest holes to be drilled leaving an undetectable permanent repair. Works on all Hardwoods, Engineered Wood & Bamboo Floors. Good for Indoors & Outdoors, Small or Large problem areas. Odorless, Very Low VOC’s. Coverage: One 10.1 oz. Fix-A-Floor Repair Adhesive Tube covers approximately 2 ft. x 2 ft. (4 sq. ft.). Just Drill & Fill Flooring Professionals prefer a polyurethane when fixing wood floors. The super blend polyurethane properties of the Fix-A-Floor adhesive will not foam or expand when applied and dries in 24 hrs. The adhesive when dry will move with the natural expansion and contraction of the sub floor below ensuring it will never dry and crack and lose its bond. Finally fix those loose, squeaky, bouncy wood floors forever. The Original Fix-A-Floor is good for wood flooring repair for smaller spot fixing, we recommend the Fix-A-Floor Polyurethane for small and larger wood flooring applications. Not recommended for use in moist or wet areas. The Fix-A-Floor Large Application Syringe is another fantastic way to apply Fix-A-Floor if you wish to drill an even smaller hole than 9/64" to fix those loose, squeaky, bouncy wood floors. Always test in a small area first to ensure desired results. Keep from freezing before use. Directions for Fixing Wood Floors: 1.Locate problem areas by tapping with wooden dowel, broom handle or similar, mark perimeter with chalk or painters’ tape. 2.Inside the marked area use a 9/64" drill bit and drill at least 1 hole on each end of problem floorboard(s), larger areas may require additional holes. Vacuum over each hole to clear debris. 3.Pull cap off tip and unscrew the tip to pierce a large hole using an awl or similar into the top of the threaded tube. If needed poke hole with awl through tip to clear, screw tip back on tube. 4.Using a quality caulk gun begin filling Fix-A-Floor into each drilled hole. Once adhesive spills up and out of nearby hole(s) this ensures complete coverage. Place finger over tip to avoid spillage when moving between holes. 5.Once filled, wipe clean with damp rag/sponge, and allow to cure for 24 hours before filling holes. Visit your local flooring/home improvement store to locate matching wood putty/filler and fill holes. For any excess residue please use mineral spirits to wipe clean. Your Floor is FIXED!
$49.95
A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength after 3 days. Features: -Araldite is stronger than other glues due to the chemical reaction of the two parts -Bonds a variety of surfaces -Dries Clear -Very Strong, durable bonding -Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) -Forms a rigid, durable bond -Can be used for gap filling (surfaces need not mate closely) -Good chemical resistance -Heat Resistant -Clamping is recommended to achieve a stronger bond -Not suitable for bonding plastics such as Polypropylene and Polyethylene -Bond strength weakens above 80°C but strength is regained when temperature drops Appearance: Translucent Where can this product be used? -Load bearing repairs -Gluing the head back on your hammer -Fixing loose table or chair legs. -Bonding solid pieces of Aluminium sheeting -Bonding timber on your boat -Repairing splits and cracks in Cricket bats -Bonding fibreglass sheets -Repairing Ski’s -Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? -Glass -Metal -Wood -Fabric -Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics -Crystal -Leather How to use this product -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each -Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. Handy tips -For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. -To extend product life replace caps immediately after use. Ensure you wipe excess from the nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. -When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) -Wipe off any uncured Araldite with acetone or nail polish remover. -To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. -To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. -Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. -Clamping recommended for a stronger bond. -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. -Ensure the surface is dry before applying the product. Safety tips: -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Do not use solvents near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention -Non-toxic when set. -For further information refer to the Material Safety Data Sheet (MSDS). -Storage and re-use -Ensure caps are replaced and product stored in a cool dry place.
$17.00
Earl’s MulTfill Multi-Purpose Paintable Putty Brand: Earl’s Earl’s MulTfill is a premium, ready-to-use multi-purpose filler designed for fast, clean, and durable repairs across interior and exterior projects. The heavy-bodied formula spreads smoothly, levels cleanly, and dries hard without shrinking, sinking, cracking, or falling out. With zero VOCs and no acrylics, latex, or solvents, it’s a low-odour choice for homes, workshops, and job sites. Clean-up is simple with water, and once dry MulTfill sands easily to a fine, paint-ready surface. Why you’ll love it Ready from the tub: no mixing, no mess, no wastage — just open, apply, and close. Zero VOCs: stable, low odour and user-friendly. Non-sinking, non-shrinking: fills stay flush and true. Won’t fall out: dries hard for lasting repairs. Paintable finish: accepts most coatings for a seamless result. Sands like a dream: refined finish without clogging when sanded dry. Long shelf life: keep the lid sealed and it’s ready when you are. Where it works Use MulTfill on common building materials including wood (including weathered and damaged sections once sound), masonry, plasterboard, cement sheet, concrete, and primed metal. It’s ideal for nail holes, dents, shallow voids, corner repairs, skim touch-ups, and general surface preparation before painting. Colour options White, Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut. How to use Prep: Ensure the area is clean, dry, and sound. Remove loose material and dust. For best glide, lightly wet your putty knife. Apply: Press firmly to fill the defect and smooth off. For deep voids, apply in layers up to 6 mm per pass, allowing each layer to dry before the next. Sand: Once fully dry, sand with 120 grit or finer to achieve a smooth, level surface. Coat: Prime if required, then paint. For clear finishes, tint the filler with suitable colorants or oxides before application to harmonise with surrounding material. Cleanup & care: Clean tools with water. If product thickens in the tub, add a few drops of clean water and stir until smooth. Always reseal promptly. Pro tips Feather edges wide when blending across boards or wall patches. On exterior jobs, protect from rain during cure and overcoat appropriately for exposure. Tinting before clear coats helps the repair visually disappear on timber substrates. Specifications Brand Earl’s Product Type Multi-purpose paintable putty / filler (water-based) Use Interior and exterior VOC Zero VOC Contains No acrylic, latex, or solvents Substrates Wood, masonry, plasterboard, cement sheet, concrete, primed metal Application Thickness Up to 6 mm per layer; allow to dry between layers Sanding Dry sand; 120 grit or finer Overcoating Accepts most paints; for clear coats, tint filler first for best colour match Clean-up Water Colours White; Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut Pack Sizes 140 g, 600 g, 1 kg, 2 kg, 3 kg (varies by colour) Shelf Life Up to 5 years if sealed and stored correctly Country of Origin Australia Storage Keep container tightly closed when not in use. Store in a cool, dry place out of direct sun. Avoid prolonged freezing. If product thickens, add a few drops of water and mix to restore spreadability. What’s in the tub A smooth-spreading, heavy-bodied filler that levels cleanly, sands easily, and delivers a paint-ready finish across interior and exterior surfaces — with no mixing, no fuss, and no strong odour.
$6.00 - $52.00
![Sika SikaSeal Roof & Gutter Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9318324010461.png?v=1754724138&width=645)
![Sika SikaSeal Roof & Gutter Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324010454.png?v=1754724138&width=645)
SikaSeal® Roof & Gutter Silicone Sealant Product Type: 1-component neutral cure roof and gutter silicone sealant Product Overview SikaSeal® Roof & Gutter is a versatile, one-component, neutral curing silicone sealant designed for use in roofing and guttering applications. This sealant offers excellent adhesion to a variety of construction materials and is ideal for sealing roofs, gutters, and plumbing fixtures, both for exterior and interior applications. It cures quickly and provides a flexible, waterproof seal with superior temperature resistance. Key Features Neutral cure, low odour formula Excellent adhesion to common construction materials such as glass, metals, ceramics, tiles, plastics, concrete, and rubber Fast curing with a non-sag formula for easy application Interior and exterior use with a temperature resistance range of -40°C to +150°C High movement capability (±25% for translucent, ±50% for coloured variants) Waterproof seal for durable, long-lasting performance Non-toxic and water-potable approved per AS/NZS 4020:2018 Applications SikaSeal® Roof & Gutter is ideal for: Roof and gutter sealing Sealing polycarbonate roof sheeting General sealing around plumbing fixtures and penetrations Sealing interior and exterior joints Specifications Packaging 300ml cartridge Shelf Life 12 months (if stored properly) Colours Available Translucent, Grey, White, Black Density Translucent: ~1.02 kg/l, Colours: ~1.39 kg/l Shore A Hardness Translucent: ~26, Colours: ~46 Elongation at Break Translucent: ~250%, Colours: ~310% Movement Capability Translucent: ±25%, Colours: ±50% Service Temperature -40°C to +150°C Application Instructions Ensure the substrate is clean, dry, and free from oils, grease, dust, and other contaminants. For optimal adhesion, follow the recommended priming procedures based on the substrate type (non-porous or porous). Apply SikaSeal® Roof & Gutter using a sealant gun, ensuring full contact with the joint sides. Tool the sealant immediately after application for a smooth, durable finish. Important Considerations Do not apply on natural stone or bituminous substrates Not recommended for use under water pressure or in permanent water immersion Pre-test required on stressed polyacrylate and polycarbonate materials May cause discoloration on light-colored silicone when exposed to UV radiation (this does not affect the product's performance) Not suitable for use in confined spaces with no air circulation (requires atmospheric moisture to cure) Packaging & Storage Store in the original, unopened packaging in a dry location between +5°C and +25°C. Shelf life is 12 months from the production date under proper storage conditions. Contact & Ordering For more information or to place an order, contact us at admin@gluesaustralia.com.au
$13.00
![Sika Sikasil Pool Silicone Water Resistance [White]](http://gluesaustralia.com.au/cdn/shop/files/7612894609400_e5cdedf3-65af-430d-be37-52c0a1c7ff7a.png?v=1754711689&width=645)
$28.10
Sikaflex®-111 Stick & Seal White: The Multipurpose Adhesive & Sealant Product Overview Experience the versatility of Sikaflex®-111 Stick & Seal, a 1-part adhesive and sealant that caters to both internal and external projects. Key Advantages Bonds to a plethora of substrates without the need for surface pre-treatment Excellent adhesion to damp concrete Compatible with a multitude of construction materials Strong mechanical and weathering resistance CE Marking for quality assurance Usage Sikaflex®-111 is perfect for bonding and sealing the following materials: Concrete Masonry Most stones Ceramic Wood Metal Glass Various Plastics Packaging Available in 290 ml cartridges, 12 per box. Application Instructions Ensure the substrate is clean and free of contaminants for optimum adhesion. For detailed application instructions, please contact Sika Technical Services.
$25.02
SikaBond®-145 SuperGrip Premium polyurethane construction adhesive with fast build up of Strength SikaBond®-145 SuperGrip is a premium grade one-component polyurethane construction adhesive with good initial grab and high strength after 30 minutes^. SikaBond®-145 SuperGrip is a versatile, ready to use, fast curing, general purpose construction adhesive suitable for interior and exterior use. One-component. Interior & exterior. Non-shrink. Usage SikaBond®-145 SuperGrip is suitable for use in construction and repair applications where a permanent strong bond is required between porous-nonporous surfaces. SikaBond®-145 SuperGrip is suitable for bonding most common construction materials such as: Wood MDF Concrete Brick Metal Polystrene Polyurethane foam Some PVC Marble Granite Ceramic LOSP Timber Advantages One-component. Interior & exterior. Non-shrink. Non-sag. High initial grab. Adheres rapidly. Stong bond in 30 minutes^. Fast cure. Solvent-free. Resistant to heat. Resistant to weathering. Water resistant -D4 according to DIN En 204 Applies white, can dry translucent if applied in thin layers.
$24.15
SikaBond®-115 Max Tack is a 1-part construction adhesive with high final strength, designed for bonding most construction material substrates. It is suitable for internal and sheltered outdoor use. Key Features: Easy to apply Easy to clean Rapid build-up of strength High final strength Very low emissions (Acrylic dispersion) Applications: Ideal for bonding various construction components, including: Skirting boards Wooden frames Battens Mouldings Panels Terracotta tiles Anodised aluminium Polystyrene mouldings and ceiling tiles Bonds well to materials like: Concrete Mortar Fibre cement Wood Painted surfaces Shelf Life & Storage: Shelf life: 18 months from production date. Storage conditions: Store in original, unopened, undamaged packaging in a dry environment, at temperatures between +5°C and +25°C. Technical Details: Density: ~1.40 kg/l (ISO 1183-1) Application Instructions: Follow standard building and construction practices when applying SikaBond®-115 Max Tack. Substrate Preparation: Ensure the substrate is clean, sound, dry, and free from contaminants like oil, grease, cement laitance, old sealants, and loose paint. Remove dust and friable material through wire brushing, grinding, sanding, or other mechanical methods. For best results, follow these priming and pre-treatment steps: Non-Porous Substrates: For surfaces such as aluminium, anodised aluminium, stainless steel, PVC, and glazed tiles: Slightly roughen the surface using a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Wait 15 minutes before applying adhesive (within 6 hours). For metals like copper, brass, and titanium-zinc: Clean and pre-treat using Sika® Aktivator-205. After 15 minutes, apply Sika® Primer-3 N by brush. Wait at least 30 minutes (within 8 hours) before applying adhesive. Porous Substrates: For concrete, aerated concrete, mortars, and bricks: Prime the surface with Sika® Primer-3 N. Wait at least 30 minutes (within 8 hours) before applying adhesive. Note: Primers are adhesion promoters and are not a substitute for proper surface preparation. They also enhance the long-term bond strength. Cleaning of Tools: Clean tools and equipment immediately after use with Sika® Remover-208. For skin cleaning, use Sika® Cleaning Wipes-100. Once cured, the adhesive can only be removed mechanically. For more information, please consult Sika Technical Services.
$17.40
Selleys MarineFlex delivers a waterproof seal for joints & gaps, even under water*. Suitable for boats, pools & spas. MarineFlex high-performance adhesive sealant can be used on boats, pools & spas, where you need a waterproof seal or bond, even underwater* It can be applied & will cure under water – no need to drain your pool or spa. Compared to traditional polyurethanes it provides a more durable seal & bond with superior UV resistance. Features Salt, fresh & chlorinated water (pools/spas)^ Above and below the waterline No primer required Shock absorbing & vibration dampening Solvent & isocyanate free Sandable when fully cured Powered by Sil-X advanced polymer technology Limitations #Not suitable for PP, PE or PTFE *critical seals/repairs underwater should be regularly checked & repaired if required. Not for polycarbonate and Perspex underwater ^Gelcoat must be lightly sanded prior to product application Where can this product be used? Suitable for boats, pools & spas^ What materials is this product suitable for? Metals Glass Ceramic Tiles Sealed/painted timber & concrete Fibreglass Gelcoat* Most plastics# (pre-test before use)
$25.00
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$26.95
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$4.43
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$24.50
Marathon Scale and Rust Remover CONCENTRATED 2L Bottle Tough on calcium, rust and scale deposits. Ideal to use on tiles, porcelain, sinks, showers and baths
$7.00
![Parfix Roof Gutter Concrete Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697115768_c056520c-16e5-4bd6-9d65-de084d15ff93.jpg?v=1754712245&width=645)
Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
$9.35
Parfix Maxi Nails 300g: The Ultimate Multi-Surface Construction Adhesive Key Features High-strength bond suitable for a variety of applications Paintable for aesthetic versatility Effective both indoors and outdoors Specifications Colour: Beige Model Name: Parfix 300g Maxi Nails Construction Adhesive Material: Polymer Dissolved in Hydrocarbon Solvent Outdoor: Yes Indoor: Yes Why Choose Parfix Maxi Nails 300g? Designed to handle a multitude of construction challenges, Parfix Maxi Nails 300g provides a robust bond that lasts. Whether you're working indoors or taking on external projects, this adhesive is formulated to give you the results you need.
$4.19
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/9310492265001_6fb5fccc-7784-41bb-9997-bbd917e3c834.png?v=1754712704&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$22.51
Earl’s Graffiti Barrier & Remover System – Non-Toxic, Biodegradable Stop graffiti before it sticks—and remove it fast when it does. This two-part system pairs a sacrificial Graffiti Barrier coating with a powerful, non-caustic Graffiti Remover. Use the Barrier to shield vulnerable surfaces so future tags release easily, and use the Remover to dissolve existing graffiti on common building substrates. Both products are non toxic, contain no caustic soda, and are designed for safe, simple use in domestic or commercial settings. Why choose this system Complete solution: Protect plus remove—works as a proactive coating and a reactive cleaner. Non-toxic & biodegradable: No caustic soda; safer handling and cleanup. Wide surface compatibility: Brick, cement render, timber fences, stone, metal, garage doors, and signage (always test first). Fast turnaround: Barrier rolls or brushes on quickly; Remover dissolves graffiti that can be rinsed away with water. Made for Australian conditions: Practical directions for real-world sites—homes, schools, retail, body corporate assets, and councils. What’s in the box Earl’s Graffiti Barrier: A sacrificial, protective coating that forms an invisible* shield to make future clean-downs faster and gentler. Earl’s Graffiti Remover: A non-caustic cleaner that dissolves graffiti so residues can be scrubbed and rinsed away. *Appearance may vary by substrate; see Specifications and always test a small area first. Where to use Masonry: Bricks, blockwork, stone, concrete/cement render. Timber & metal: Timber fences, metal doors, garage doors, and metal signage. High-risk zones: Laneways, rear service doors, fence lines, public-facing walls, and transport corridors. How it works The Barrier creates a sacrificial layer. When tagging occurs later, graffiti sits at or near the surface and releases more readily during cleanup. The Remover penetrates and dissolves paints/inks so they can be agitated and rinsed from the substrate, especially effective on porous mineral surfaces and surfaces previously treated with the Barrier. Directions 1) Apply the Graffiti Barrier (preventive) Prep: Surface must be clean, dry, sound, and free of dust, oil, or old failing coatings. Mask adjacent areas. Application: Stir/shake well. Apply sparingly by roller or brush in a single, consistent roll direction. Coverage: Up to ~6 m²/L on render or dark/porous surfaces (coverage varies by substrate profile and porosity). Conditions: Do not apply below 12 °C or in very cold/damp conditions. Appearance: Dries to an opaque protective film; test a small inconspicuous area to confirm finish/visual impact. 2) Use the Graffiti Remover (reactive) For unpainted mineral surfaces: Spray or liberally apply Remover directly to the graffiti. Allow time for the film to soften/dissolve. Agitate: Scrub with a stiff bristle brush to lift residues from pores and profiles. Rinse: Wash off thoroughly with clean water. Repeat on deeply embedded areas if required. Barrier not previously applied? The Remover can still be used to clean most common surfaces; repeat as necessary. Pro tips Always conduct a spot test in an inconspicuous area to verify appearance and cleaning performance. Highly porous or dark substrates may need additional coats of the Barrier for consistent protection. Schedule maintenance inspections in high-risk locations so tags are removed promptly, discouraging re-offending. Clean-up & safety Use appropriate PPE (gloves/eye protection). Provide ventilation when working in enclosed areas. Avoid runoff into drains and waterways. Collect residues where practical and dispose of in accordance with local regulations. Store sealed in a cool, dry place away from direct sun and sources of ignition. Keep out of reach of children. Specifications Property Graffiti Barrier Graffiti Remover Function Sacrificial protective coating to ease future graffiti removal Non-caustic graffiti dissolver for reactive cleaning Key claims Non toxic, non caustic, biodegradable Non caustic; designed to dissolve graffiti for water rinsing Suitable substrates Brick, cement render, stone, timber fences, metal, garage doors Brick, cement render, stone, timber fences, metal, garage doors, metal signs Appearance / finish Dries opaque (test first for visual impact) Clear liquid cleaner (appearance varies by manufacturer’s batch) Application method Roller or brush (single roll direction) Spray/apply, dwell, scrub, rinse with water Coverage (guide) Approx. 6 m²/L on render or dark/porous surfaces (substrate dependent) Consumption varies with thickness of graffiti and porosity Application temperature Do not apply below 12 °C Use in ambient conditions; avoid extreme heat/cold; ventilate area Cleanup Allow to dry; future clean-downs remove tags more easily Rinse dissolved residues thoroughly with clean water Typical uses Preventive protection for high-risk surfaces Removal of existing tags and markers
$33.00
Earl’s Powder Putty – Mix-to-Use Interior & Exterior Filler Earl’s Powder Putty is a multi-purpose powder filler for professional and DIY repairs. Just add water, mix only what you need, and achieve a tough, easy-sand finish with no waste and no shrinking. Brand: Earl’s Interior and exterior use* Mix-on-demand convenience Non-shrinking, smooth finish Easy sanding and shaping Indefinite shelf life in dry powder form Proudly made in Australia *Exterior applications must be sealed/painted and used on stable substrates. About Earl’s Powder Putty Earl’s Powder Putty delivers reliable, high-quality filling for timber, walls, masonry and metal. Because it’s supplied as a dry powder, you can tailor the mix to your task—stiffer for knife-grade filling and sculpting, or looser for fine skim work. The result is a hardwearing repair that sands easily and accepts coatings beautifully. Where Earl’s Powder Putty Works Timber & woodwork: doors, frames, skirting, architraves, furniture, cabinetry Walls & panels: plasterboard and cement sheeting patching and feathering Masonry & concrete: chips, small holes and surface imperfections Metals: minor dents and irregularities prior to priming and painting Floor preparation: quick patching of distressed boards prior to covering Craft & hobby: architectural details, mouldings and small sculpting tasks Why Choose Earl’s No shrink: Formulated to dry without shrinking for flush, invisible repairs. Mix what you need: Reduce waste and always work with a fresh batch. Shapes perfectly: Once dry, Earl’s Powder Putty can be cut, carved, sanded or sawn. Paint-ready: Accepts primers and topcoats after proper dry and prep. Economical & dependable: Indefinite shelf life in powder form when stored dry. Directions for Earl’s Powder Putty Surface prep: Ensure the area is clean, dry and sound. Remove loose material, dust, grease and contaminants. Key glossy surfaces for better adhesion. Mix: In a clean container, add Earl’s Powder Putty and slowly incorporate clean water. Stir to a smooth, lump-free paste. Adjust water to suit the task. Apply: Press the mix firmly into the repair with a putty knife or trowel. Slightly overfill to allow for sanding back flush. Build: For deep repairs, apply in layers, allowing each to firm before adding the next. Finish: Once dry, sand smooth. The cured filler can be carved or sawn to refine edges and profiles. Coat: Prime/seal and paint after full dry. For exterior use, always seal with suitable coatings. Clean-up: Clean tools with water while the product is still wet. Dry and recoat times vary with temperature, humidity and film thickness. Allow extra time in cool or damp conditions and for deep fills. Good to Know About Earl’s Not waterproof by itself: Water and weather resistance requires sealing/painting. Not flexible: Avoid use where movement, vibration or structural flexing is expected. Stable substrates only: Ensure exterior bases are sound and well prepared. Storage: Keep Earl’s Powder Putty dry and tightly closed. Moisture exposure can reduce performance after opening. Safety: Avoid dust during mixing and sanding. Use PPE and adequate ventilation. Typical Earl’s Applications Filling nail and screw holes, chips and minor cracks Skim patching and feathering edges prior to painting Rebuilding small decorative profiles and mouldings Levelling minor surface imperfections before finishing Specifications Brand Earl’s Product Name Earl’s Powder Putty Product Type Multi-purpose powder filler Format Dry powder; mix with clean water Colour (dry) Off-white to white; paintable Use Areas Interior and exterior* (exterior must be sealed/painted; stable substrates only) Substrate Compatibility Wood, plasterboard, cement sheeting, concrete, masonry, properly prepared metal Shrinkage Non-shrinking when used as directed Sandability Easy sanding once fully dry Paintability Prime/seal and paint after full dry Water Resistance Requires sealing; product itself is not waterproof Shelf Life (powder) Indefinite when stored cool, dry and sealed Clean-up Water while wet Tools Putty knife, trowel, mixing stick or paddle, sanding block Country of Origin Australia Limitations of Earl’s Powder Putty Do not use as a flexible gap filler or where structural movement is expected. Always prime/seal before exposure to moisture or exterior weather. Deep repairs may require multiple layers with adequate drying between coats. Not for permanently wet, submerged or high-movement joints. FAQs – Earl’s Powder Putty Can I mix a large batch and store it?Mix only what you can use within the working time. Discard any mix that begins to stiffen or set. Can I screw or nail into it?For non-structural tasks, light fixings may be possible in sufficiently thick, fully cured areas. Pre-drill as needed and test first. Is it paintable?Yes. Once dry and sanded, prime or seal the repair and finish with your chosen coating system. Always follow label directions. Test on a small, inconspicuous area to confirm compatibility and finish.
$10.50 - $81.00
Concremate Expanding Anchoring Cement Anchor, patch and lock in place with confidence. Concremate is a high-performance expanding cement designed for rapid, reliable anchoring and structural patching. Mixed to a workable, mortar-like consistency, it expands slightly as it cures to counteract drying shrinkage. That controlled expansion grips embedded items and surrounding material tightly, delivering a secure, long-lasting hold that stands up to strain, stress and vibration. Why choose Concremate Fast turnaround: initial set in about 30 minutes and hard in approximately 1 hour, so many jobs can progress the same day. Expands and grips: engineered expansion of about 0.125% offsets shrinkage and locks into the substrate. High ultimate strength: cures to a finish that becomes harder than standard concrete at 28 days when properly mixed and applied. Versatile application: ideal for anchoring bolts, rails, brackets and fixtures, as well as patching holes, chases and cracks. Durable performance: forms a robust, long-term bond that resists severe mechanical stress and vibration. Where it excels Use Concremate for secure embedment and structural repairs on common mineral surfaces. It is suitable for: Concrete and masonry Brickwork and stone Tiles and terrazzo Plaster and similar mineral substrates Typical projects Anchoring handrails, posts, machine base bolts, threaded rods and heavy brackets Fixing door and window hardware to masonry openings High-pressure grouting under plates, around pipe sleeves and service penetrations Patching voids, chased conduits, spalled edges and impact damage in floors, walls and ceilings How it works Concremate is a mineral-based expanding cement. After mixing with clean water, the paste hydrates and begins to set. A small, controlled expansion during cure offsets natural drying shrinkage. The result is a tight, interference-style fit that increases grip on embedded items and keys the patch into surrounding material. For best results, the material must be able to expand slightly while drying and should not be constrained in a completely sealed cavity. Directions for use Surface preparation: Remove dust, loose material, laitance, oil and contaminants. Roughen smooth surfaces and blow or brush clean. Pre-dampen porous substrates to a surface-saturated dry condition; do not leave standing water. Mixing: Add powder to clean water while stirring until a smooth, lump-free, mortar-like consistency is reached. Mix only what you can place within the working time. Do not over-water. Placement for anchoring: Fill the prepared hole or pocket from the bottom up to avoid entrapped air. Insert the fixture or fastener while the mix is workable and align immediately. Hold steady until initial set. Placement for patching: Tightly pack the mix into the void in layers, compacting each layer to ensure full contact. Strike off and finish the surface as required. Curing: Protect from rapid drying, wind and direct sun during early cure. Avoid vibration or load until the material has hardened. Cleanup: Clean tools and splashes with water while product is fresh. Once hardened, mechanical removal may be required. Good practice tips Plan the job so placement occurs immediately after mixing for best expansion and bond. For deep holes or large voids, place in lifts and compact each lift. Do not confine completely in a sealed cavity; allow space for controlled expansion. Avoid adding sand, cement or other admixtures that can change performance. Performance and durability When correctly mixed and applied, Concremate develops a hard, dense matrix with strong adhesion to mineral substrates and embedded metals. The slight expansion on cure reduces micro-gapping at the interface, improving load transfer and long-term durability. After full cure at 28 days, the set material achieves hardness that exceeds standard concrete, supporting demanding anchoring and patching tasks. Safety and handling Wear suitable gloves, eye protection and a dust mask when mixing and placing. Avoid contact with skin and eyes. In case of contact, rinse with plenty of water. Store in a cool, dry place in the original, tightly closed container. Keep out of reach of children and pets. Specifications Product type Expanding cement anchoring and patching compound Form Premixed dry powder Color Grey Mix consistency Mortar-like paste when mixed with clean water Initial set About 30 minutes (conditions dependent) Hard set Approximately 1 hour (conditions dependent) Ultimate hardness Harder than standard concrete at 28 days Expansion Approx. 0.125% during cure Recommended substrates Concrete, brick, stone, tiles, plaster, terrazzo Primary uses Anchoring bolts, rails, brackets and fixtures; patching holes, chases and cracks; high-pressure grouting Cleanup Water while fresh Storage Cool, dry conditions in sealed container What to expect on the job With suitable surface preparation and correct mixing, you can expect a smooth placement, quick set and a dense, high-integrity bond. The expansion action helps lock hardware and patches into place. Protect new work from early movement and moisture loss, then return to service once the hard set has been achieved and the repair or anchorage has reached the necessary strength for your application. Limitations Not for use where the mix cannot expand slightly during cure. Do not apply over active movement joints or flexible substrates. Working and set times vary with temperature, humidity and mix ratio. Note: Always trial on a small, inconspicuous area or non-critical hole to confirm suitability for your specific substrate and conditions.
$17.00 - $99.00
Agnews Water Putty - Hard-Setting Filler for Wood, Plasterboard, Concrete & More Agnews Water Putty is a professional, powder-based repair and levelling compound for durable, long-lasting results. Mix only what you need with clean water, then patch, level or rebuild surfaces with confidence. Once cured, it sets rock hard, bonds permanently, and can be sawn, drilled and sanded to a smooth, paint-ready finish. Key features Brand: Agnews Unlimited shelf life when stored dry Non cracking, non shrinking, non sinking Won't fall out – adheres firmly and fills to any depth Interior & exterior grade (seal exterior applications after full dry) Non flammable and no VOCs Mix what you need for minimal waste Suitable substrates Plasterboard, concrete, wood/timber, cement sheet, masonry. Also suitable for minor floor levelling and feathering on concrete, timber and ceramic tile substrates. Typical applications Fill holes in wood: knotholes, nail and screw holes, dents, edge build-ups Wall patching: cracks and cavities in plasterboard and cement sheet Furniture repair: tighten loose joints, reset fasteners, rebuild profiles Floor levelling: ramp or smooth minor level variations before floor coverings Trim and fixtures: refit loose door bumpers and trims with reliable hold Architectural & hobby moulding: casting and shaping durable components Why choose Agnews Agnews Water Putty cures to a dense, stone-hard finish that resists shrinkage and cracking even in deep fills. It bonds securely, stays put, and finishes cleanly, delivering a stable base for sanding, priming and painting. From small touch-ups to larger restorations, it provides consistent, professional results. Directions (general guide) Surface prep: Ensure the area is clean, dry, sound and free of dust, oil or loose material. For very porous substrates, lightly dampen to reduce rapid suction. Mix: Add powder to clean water and blend to a smooth, lump-free paste. Adjust water to suit application (thicker for filling, looser for fairing/skim). Apply: Press firmly into cracks or voids with a putty knife or trowel. Overfill slightly so you can sand back flush. Cure: Allow to dry thoroughly. Dry time varies with thickness, temperature and humidity. Finish: Sand to profile. Prime and paint or seal. For exterior applications, always seal after full dry. Exterior use guidance This is a hard-setting, non-flexible compound. For exterior use, only apply over stable substrates with minimal expansion and contraction from temperature changes. Ensure the putty is fully dry before sealing with a suitable exterior-grade coating. Finishing & compatibility Paintable and sealable after full dry; prime as required for best results. Can be cut, carved, drilled and sanded after cure without crumbling. For stained timber finishes, test a small area first for colour and absorption. Pro tips Mix small batches and use promptly. For deep voids, apply in layers if needed, allowing each layer to firm before the next. Store powder in a cool, dry place to maintain its unlimited shelf life. Clean tools with water before material cures. At a glance Substrates: plasterboard, concrete, wood/timber, cement sheet, masonry Uses: patching, levelling, rebuilding, moulding Properties: non cracking, non shrinking, non sinking, non flammable, no VOCs Finish: hard, dense, smooth and paint-ready after sanding/priming
$7.00 - $40.00
Overview This high-quality general-purpose silicone sealant is a versatile solution for a wide range of sealing and bonding applications. Engineered with neutral cure technology, it is designed to provide a durable, flexible, and weather-resistant seal that remains reliable even in demanding environments. Once cured, the sealant forms a strong rubber-like finish that is permanently elastic, ensuring long-lasting performance both indoors and outdoors. Key Features Neutral Cure Technology: Low-odor curing system suitable for sensitive applications. Permanently Flexible: Retains elasticity over time without cracking or shrinking. Waterproof Protection: Provides a watertight seal, protecting against leaks and moisture ingress. Interior & Exterior Use: Unaffected by rain, snow, extreme temperatures, or prolonged UV exposure. Excellent Adhesion: Bonds strongly to most common building materials without primer. Easy Application: Smooth flow from the tube, easy to tool and clean before curing. Applications This sealant is designed for general-purpose use across a variety of materials and environments. Its flexibility and adhesion make it suitable for: Sealing around window and door frames. Lap joints in metal guttering and roofing sheets. Bonding panels such as wood, plasterboard, insulation board, and drywall. Fixing masonry joints including sills, brickwork, and decorative trims. Gap filling around pipes, conduits, and penetration surfaces. General sealing in kitchens, bathrooms, and living areas where flexibility is required. Limitations Not suitable for permanent water immersion (e.g., underwater joints or continuous water load). Not recommended for use on polyethylene (PE), polypropylene (PP), polycarbonate (PC), polymethyl methacrylate (PMMA), PTFE, neoprene, bituminous surfaces, or very soft plastics. Not intended for deep cavity filling without adequate moisture for curing. Surface Preparation To ensure maximum performance, surfaces must be clean, dry, and free from dust, grease, or loose particles. Non-porous surfaces should be wiped with solvent and dried with a clean cloth. Porous surfaces should be lightly abraded or brushed to remove contaminants and improve adhesion. Complete any painting work before applying the sealant. Application Instructions Remove the cap and pierce the nozzle seal. Apply steadily along the joint or surface, ensuring continuous contact. Smooth or tool the bead before skin formation occurs. If masking tape is used, remove immediately after tooling to avoid tearing the cured seal. Curing At room temperature (23°C), the sealant will skin over within 15 minutes and achieve full cure within 24 hours, depending on humidity and joint depth. Once cured, it provides a permanently flexible and weatherproof joint. Cleaning & Maintenance Excess uncured sealant can be cleaned using a cloth dampened with mineral turpentine. Fully cured material should be trimmed away carefully with a sharp blade. Store unused tubes in a cool, dry place below 25°C and away from direct sunlight. Shelf life is up to 12 months from the date of manufacture. Health & Safety Use in a well-ventilated area. Avoid contact with eyes and mucous membranes, as uncured sealant may cause irritation. In case of contact with eyes, flush thoroughly with water and seek medical advice. Keep out of reach of children. Always follow safety instructions and refer to the product’s safety data for detailed guidance. Why Choose This General Purpose Silicone Sealant? This sealant is a trusted choice for tradespeople, DIY enthusiasts, and homeowners seeking a reliable solution for everyday sealing needs. Its combination of flexibility, adhesion, and weather resistance ensures that once applied, it continues to protect and bond effectively for years to come. Whether you are fixing a leaking gutter, sealing around windows, or bonding decorative trims, this product provides professional results with minimal effort. Technical Specifications Technology Neutral Cure Silicone Appearance Clear Paste Working Time Up to 15 minutes Tack-Free Time Approximately 15 minutes Full Cure at 23°C 24 hours Flexibility Permanently elastic after curing Weather Resistance Unaffected by rain, snow, UV, and temperature variations Applications Windows, doors, guttering, masonry, panels, pipes, decorative elements Storage Below 25°C, out of direct sunlight Shelf Life 12 months from manufacturing date
$9.98
Holds up to 13.6Kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$11.55
Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistantRecommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$12.95
Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$23.00
![Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240085.jpg?v=1754724137&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$0.00 - $28.00
![Sika Sikaflex Pro+ Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$24.00
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Black]](http://gluesaustralia.com.au/cdn/shop/files/2330c4b4af69418ba74ba7691a5becd0.jpg?v=1757756157&width=645)
Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
$0.00 - $17.00
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$24.43
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$12.75
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$18.48
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$9.70
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$28.21
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, benchtops, tiles, slate, stainless steel, baths, glass, stovetops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQs. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra-concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$5.33
T-Rex® Brute Force® high-performance duct tape is a bold next step in tape technology. Built with Forge-Link™ Technology, an extreme tensile cloth, one loop of T-Rex Brute Force tape holds 700+ pounds of weight, making it the strongest duct tape on the market, period. Too tough to tear by hand, this premium tape features an aggressive double-thick adhesive with a durable waterproof backing, so you can secure, fasten or hold all sorts of materials for any project, on any job site. Hold more. Do More.™ T-Rex Brute Force. FEATURES: Extreme tensile strength 1 loop of tape holds 700+ pounds of weight Made with patented Forge-Link™ Technology Waterproof backing High tack, double-thick adhesive that sticks to rougher and dirtier surfaces, withstands severe pressure UV resistant materials
$36.00
Our Quick Setting Gel Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product fills gaps and covers large porous surfaces. The final cure colour is cream but can be mixed with paint to colour match. This product sets in only 5 minutes. Works best on: • Porous materials • Ceramic • Metal • Pottery • Wood • Tile • Crafts Properties: Initial colour: Green resin/white hazy hardener Maximum Gap: .25” Final colour: White hazy Hardness, Shore D: 75-85 (After full cure) Set Time: 4-6 minutes @ 65-80F Shear Strength, Steel: 1500 psi (± 20%) Handling Time: After 1 hour Aluminum: 900 psi (± 20%) Full Strength: 24 hours Operating Temperature Range:-320 to 3000F (-360 to 1490C) Instructions: 1. Surfaces should be clean and dry, free from oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from container following package directions & mix thoroughly approximately 1 minute. Use package blister or clean cardboard for mixing container, do not use metal. 4. Apply to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F / 25C) with full cure in 24 hours. Helpful Hints: To colour Epoxy Gel, do test sample using mixed epoxy with added small amounts of colourant, such as paint (latex or oil), stain or tint. Mix well & apply to scrap piece of wood. Let dry to compare the final colour to the color of repair item. Keep testing until a colour match is achieved, then mix the appropriate amount of colourant with Epoxy Gel and bond repair item.
$9.95
The Permanent Patch is a very unique, easy-to-use UV or sunlight activated repair patch. It is fiberglass-reinforced polyester and creates long-lasting repairs. No mixing is required - one step no mess. This incredible permanent patch is waterproof and will not rot or rust. It can be drilled, tapped, sanded and painted in less than an hour. The Permanent Patch makes long lasting repairs on Everything Under The Sun™. Works best on Aluminum Concrete Drywall Fiberglass Metal Most Plastics Pottery PVC Pipe Rubber Stucco Wood USE INSTRUCTIONS: NOTE - This product must be exposed to UV sunlight or UV source to cure. Rubber or plastic gloves recommended for sensitive individuals. Not recommended for drinking water applications. 1. Use the Anchor-Tite Patch in a well-ventilated area. Keep the Patch in the black, UV-protected package until you are ready to do a repair. 2. Clean parts to be repaired with soap & water and allow to dry completely. Roughen surface with wire brush or sandpaper. 3. While still in the black UV-protected package, cut the patch material to extend ¾” beyond the repair area using scissors or knife. Remove the white backing and apply cut Patch over repair and press firmly in place. Store unused portion away from sunlight or UV sources. If outside surface is to be painted or finished, remove clear nylon film prior to cure. 4. Expose the bonded Patch to UV sunlight, black lamp or other UV sources until the product is hardened (see approximate times above). 5. After the product is hard and fully cured, it can be drilled, sanded or painted. 6. Wash hands and skin well with soap and water after use. STORAGE AND SHELF LIFE Store product sealed in the original black UV-protected package in a cool (<75F), dry location away from UV sources or sunlight. Stored under these conditions, a one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS Contains Styrene. Eye, skin & respiratory irritant. Use & store in a well-ventilated area away from heat & sunlight. Avoid contact with eyes & skin. Do not ingest. Wash hands & skin with soap and water after use. If eye contact occurs, flush with water for 15 minutes & get medical attention. With skin contact, if irritation persists, get medical attention. If swallowed, do not induce vomiting; get immediate medical attention & show container label. KEEP OUT OF REACH OF CHILDREN.
$35.00
Fix-All Adhesive is a great all-purpose solvent glue and sealer. It seals and repairs almost any surface easily and quickly. A great product for gluing wood, fabric, brick, canvas, and concrete. Also repairs tears and helps fill cracks and holes. Pacer Technology Super Glue Fix-All Adhesive (T-FA) is a single component adhesive that glues, seals and repairs and is best used for: • Metal • Plastics • Ceramics • Wood • Glass • Rubber • Fabrics • Brick • Leather • Canvas • Concrete • China • Vinyl • Porous materials • Non-Porous materials Properties: Initial colour: Clear Final colour: Clear to light yellow Open Time: 10 minutes Dry Time: 30 minutes Handling Time: 3 hours Full Strength: 24 hours Operating Temperature Range: -200 to 1500F (-290 to 660C) Instructions: Use in a well-ventilated area. Protect work surfaces. As a glue: Apply to both surfaces and let dry 10 minutes. Press parts together. Full cure in 24 hours. For rough, uneven or very porous surfaces, apply a thick layer to both surfaces and wait 30 minutes before joining parts. As a sealer: Fill crack or hole with extra amounts of Fix-All and allow to dry. Add additional adhesive as needed. For repair: To repair vinyl, rubber or fabric tears, apply Fix-All with a spatula behind, through and above the tear. Hold sides together using a strong piece of tape across the tear to hold it tightly. Remove tape after 3 hours. Remove excess with a rubber eraser. Note: when thick layers are required it is better to apply a number of thin coats. Allow curing for 3 hours before handling. Full cure in 24 hours. Notes: Solvents may evaporate from bottle or tube if left open for prolonged periods. Not recommended for Teflon, Polyethylene or Polypropylene bonding. Avoid constant submergence in water and exposure to extremely high temperatures after cure. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains xylene, naphtha and ethylbenzene. DANGER: liquid adhesive is Extremely Flammable. Harmful or fatal if swallowed. Vapour harmful. Avoid breathing vapours. Use and store in a well-ventilated area away from heat, sparks or flame. May cause eye/skin irritation. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN.
$25.00
$15.00
This acrylic-based Industrial Strength product dispenses resin and hardener automatically into equal parts with one push. Hold surfaces together with clamp, tape or weights allowing 5-10 minutes setting time. Works well on plastic toys, fixtures made of plastic, metal, concrete and many other materials. Cures to an opaque light yellow colour. Works best on: Plastics Metal Concrete Glass Ceramics China Properties: Initial colour: Light yellow to amber Final colour: Light yellow Positioning Time: 3 – 5 minutes Set Time: 5-10 minutes @ 65-80F Handling Time: 2 hours Full Strength: 24 hours Instructions: (Note: not recommended for polyethylene or polypropylene bonding). 1. Surfaces should be clean and dry, free from oil and grease. 2. Roughen surfaces with emery cloth or sandpaper & wipe clean with a solvent for best results. 3. Dispense from the syringe and mix thoroughly approximately 1 minute. 4. Apply to both surfaces and mate parts together. 5. Remove excess glue immediately with denatured alcohol. 6. Sets in 5-10 minutes at room temperature (77F or 25C) with full cure in 24 hours. Storage: After use, pull back on the plunger, wipe tips to remove residual product and reseal with plug. Store product sealed, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected. Safety: WARNING: FLAMMABLE. Eye and skin irritant. Contains Methyl methacrylate. May cause sensitization by skin contact. In case of direct eye contact, flush with water for 15 minutes and consult a physician. Wash hands and skin thoroughly with soap and water after use. If swallowed, seek medical advice immediately and show container label. Use with adequate ventilation. Keep out of reach of children.
$9.95
Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance. Incredible bond strength Waterproof Superior strength Adheres to even visibly damp surfaces Fast curing - less than 30 minutes Materials: wood, ceramic, stone, concrete, metal, glass, fibreglass, leather, laminate, masonry, plasterboard and some plastics.
$25.98
Tarzans Grip Mega Bond Glue is suitable for bonding large variety of surfacees in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resitance. Incredible bond strength Waterproof Adheres to even visibly damp surfaces Fast curing - less than 30 minutes
$10.50
Tarzan's Grip 5min Epoxy is a two-part all purpose adhesive. When mixed equally together it provides a tough, rigid, high strength bond to tackle the toughest DIY projects. Its also fast - sets in 5 minutes and reaches initial handling strength in 30 minutes. Easy mix Durable bond Dries clear Water resistant
$12.29
![Sika SikaSeal Flexible Gap Filler Super-200 Paintable [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/9318324010690_a135bef3-1e63-49fe-b52d-552f6c48153c.png?v=1754711651&width=645)
SikaSeal® Super-200 is great for sealing of connection joints with moderate movement Good UV resistance Low odour For exterior and interior use USE Sealing of connection joints with moderate movement around windows, window sills, doors, PVC pipes, dry partition walls and ceiling Filling of cracks on interior and exterior walls (with no permanent water immersion) CHARACTERISTICS AND ADVANTAGES For exterior and interior use High movement capability ±12.5% Good UV resistance Solvent-free, low odour Overpaintable Very good adhesion on most construction materials such as concrete, plaster, wood Possible storage at -10°C for short period of time (max 24h) Conforms to EN 15651-1 F INT EXT
$6.73
Sikaflex®-111 Stick & Seal Grey: The Multipurpose Adhesive & Sealant Product Overview Experience the versatility of Sikaflex®-111 Stick & Seal, a 1-part adhesive and sealant that caters to both internal and external projects. Key Advantages Bonds to a plethora of substrates without the need for surface pre-treatment Excellent adhesion to damp concrete Compatible with a multitude of construction materials Strong mechanical and weathering resistance CE Marking for quality assurance Usage Sikaflex®-111 is perfect for bonding and sealing the following materials: Concrete Masonry Most stones Ceramic Wood Metal Glass Various Plastics Packaging Available in 290 ml cartridges, 12 per box. Color Options Choose from White, Concrete Grey, or Black to match your project requirements. Application Instructions Ensure the substrate is clean and free of contaminants for optimum adhesion. For detailed application instructions, please contact Sika Technical Services.
$25.02
Sikaflex®-111 Stick & Seal Black: Seal, Bond, and Build with Ease Product Overview The one-stop solution for all your adhesive and sealing needsSikaflex®-111 Stick & Seal Black. Advantages Bonds effortlessly to a myriad of substrates with no surface pre-treatment needed Excellent for use on damp concrete Fully compatible with most construction materials Durable against weathering and mechanical wear CE Marked for quality assurance Usage Scenarios This versatile product is perfect for: Concrete Masonry Stones Ceramic Wood Metal Glass Plastics including PVC, PA, PET, and EPS/XPS Packaging Available in 290 ml cartridges, packed 12 cartridges per box. Color Options Also available in White and Concrete Grey. Application Guidelines For best results, the substrate should be free of contaminants. Further instructions for both porous and non-porous substrates are available. Cleaning & Maintenance Use Sika® Remover-208 for cleaning tools and Sika® Cleaning Wipes for skin.
$25.02
You have seen 48 out of 263 products
Find products tagged for use on concrete. This collection includes adhesives, sealants, tapes and accessories chosen for typical repairs and installs on concrete surfaces. Compare cure speed, flexibility, clarity and temperature ratings to match your project. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
