Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$15.46
Selleys White For Life Ready To Use Grout is a premium-quality, pre-mixed grout designed to deliver a brilliant, long-lasting white finish for wall and floor tiles. Suitable for interior applications with joints up to 5mm, this product is ideal for both new tile installations and regrouting jobs. Surface Preparation: Ensure all surfaces are clean, dry, and free from dust, oil, old grout, and other contaminants. For new tiling jobs, let tile adhesive set for at least 24 hours. For regrouting, completely remove old grout and thoroughly clean the joints. Application Instructions: Cut the cartridge tip and attach the nozzle. Trim to desired bead width. Using a caulking gun, apply grout into joints, pressing it in to eliminate air gaps. Smooth grout using a rubber float or grout applicator, working diagonally. After 15–20 minutes (depending on temperature), gently wipe tile surfaces with a damp sponge to remove excess grout and haze. Avoid over-wetting and excessive wiping, which can weaken the grout lines. After 24 hours, polish tile surfaces with a soft dry cloth to remove any remaining haze. Coverage: Approx. 2m² per 410g cartridge (based on 300x300mm tiles with 3mm x 5mm joints) Drying Time: Touch dry in 30 minutes Allow 72 hours before exposing to water in wet areas such as showers Clean-Up: Clean tools and tile surfaces with water before the grout cures Once dry, remove excess grout by mechanical means Technical Data: Colour: White Appearance: Smooth, creamy paste Joint Width: Up to 5mm Water Clean-Up: Yes (before curing) Shelf Life: 12 months if stored unopened in a cool, dry place
$16.00
Selleys White For Life Ready To Use Grout is a water-based easy to use, brilliant white grout, ideal for wall and floor tiles and for joints up to 5mm wide. It resists yellowing, staining or blackening, when used as a part of the Selleys White For Life™ Tiling System and as per pack directions*. Provides superior water resistance, mould and soap scum resistance White For Life – Always looks like new* Resists yellowing, staining and blackening* Crack resistant Sand free - resists scratching files Suitable for indoor wall and floor tiles Comes in a cartridge for minimum wastage Where can this product be used? Bathrooms Showers (walls only) Toilets Laundries Kitchens What materials is this product suitable for? Ceramic tiles Porcelain tiles Stone tiles Most other tiles Please contact your store to confirm avaliability, as some stores may have a limited range. How to Use Preparation For new tiling jobs, use Selleys White For Life Tiling Adhesives. Ensure that the tile adhesive has set (usually 24-48hrs). Remove spacers, rake out excessive, dust, debris etc from the joints. If re-grouting remove old grout and clean thoroughly with Selleys Rapid Mould Killer and allow to dry. Do not grout at temperatures below 10°C, or in damp conditions. Before grouting, check ease of removal from matt or textured tile surfaces. Seal porous tiles before grouting or removal of grout from tiles will be difficult. Application Cut seal, screw on nozzle, cut to size. Apply with a caulking gun, forcing grout into joints (for cartridge only). Grout small areas at a time. Work the grout into the joints and smooth off using a rubber squeegee or grout float, moving diagonally across the joints with several passes to compact the grout lines and minimise the amount left on the face of the tiles – avoid moving along the joint as this removes grout from the joint. Tip: hold float/squeegee at 45° angle; clean regularly. Clean up with water, before grout sets. Allow grout to firm up in joints for approx 20 min (longer in colder conditions). Using a damp (not wet) sponge, clean tile surfaces, by wiping lightly, in a circular motion. Finish with a single wipe diagonally across the tile with a clean damp ( not wet) sponge. Avoid repeated wiping as this may remove grout which is not yet fully set, from the joints. Buff and polish the tile surface, after 24hours, with a soft clean cloth. Use Selleys White For Life Grout Cleaner for any stubborn haze marks. overage 1 cartridge is sufficient for 2sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm). 1.4kg is sufficient for 6sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm). Limitations: Not for areas frequently immersed in water eg. Shower floors. Allow to dry for 3 days before exposing grout to water on shower walls. Handy tips If the grout is overworked or excessive water is used to smooth off, it may appear to shrink – simply apply a second coat to affected areas. *To maintain whiteness and long term stain & mould resistance: Allow grout to set for 3 days before sealing Selleys White For Life Sealer for maximum stain resistance. Reapply sealer annually or whenever grout has been scrubbed hard. Clean grout and tiles regularly with Selleys White For Life Tile & Grout Cleaner to avoid build up of soil or soap scrum. Do not use harsh acidic cleaners. Areas subject to high foot traffic will require frequent cleaning. Clean up spills immediately – grout will resist penetration by common stains for up to 10 minutes. Coverage guide 1 cartridge is sufficient for 2m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm) 1.4Kg is sufficient for 6m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm) Clean Up Clean up tools with water before product hardens. Uncured product may be removed with water.
$34.00
Introducing Selleys Water Shield, your go-to solution for making your fabrics water, snow, and ice-repellent without compromising comfort and breathability. Ideal for active individuals and outdoor enthusiasts, this product is designed to keep you dry while ensuring maximum comfort. Key Features Water, Snow, and Ice Repellent: Provides an effective barrier against moisture and cold elements. Breathable: Does not impair the comfort and breathability of the material, making it ideal for sportswear. Where to Use Sportswear, such as ski parkas, gloves, etc. Athletic shoes, including sandshoes and jogging shoes. Camping gear, like tents and sleeping bags. Cloth and canvas bags. Umbrellas. Outdoor furniture, e.g., canvas chairs. Paper maps and plans. Suitable for the Following Materials: Fabric Canvas Nylon How to Use Preparation: Ensure that the item to be treated is clean and dry. Application: Hold the aerosol can upright, approximately 100-150mm (4-6 inches) away from the surface. Spray: Use a sweeping motion to spray until the surface is moist. Dry: Allow approximately 3 hours for drying before using the item. Limitations Not suitable for leather or suede articles. Avoid use on fabric already treated with water repellents like DRW or waterproof materials like Gore-tex® or Driza-bone®. Do not apply to areas that don't require protection (e.g., soles of shoes). Handy Tips Test for colorfastness in an inconspicuous area before full application. Start spraying light-colored areas first, followed by darker areas. Launder or dry-clean soiled articles as usual and reapply the Water Shield. Specifications Size: 200g Aerosol Can Color: Colourless Technology: Silicone-Based Use: Suitable for both interior and exterior applications Keep your gear and clothing dry and comfortable. Experience the protection and convenience of Selleys Water Shield today!
$21.00
Selleys Original Sugar Soap is a powerful liquid household cleaner which is effective in removing grease, grime and dirt from household surfaces. It can be diluted with water or used neat. Also recommended for cleaning surfaces prior to painting and wallpapering. Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Features Concentrated – makes up to 30 litres Professional strength grease & grime cleaner Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Can be diluted with water or used neat Where can this product be used? Kitchen surfaces – to clean floors, walls and cupboards Bathroom & Laundry surfaces – to clean bathtubs, showers, sinks, toilet bowls and tiled surfaces Painting & Wallpapering – wash surfaces prior to painting General Cleaning – appliances, stainless steel, blinds and more What materials is this product suitable for? Floors Tiles Walls Benchtops Cooktops Appliances Wipe off immediately from aluminium and brass surfaces Handy tips Dilute to suit the cleaning task. Liquid Sugar Soap, as a phosphate-based cleaner, can be used as part of lead residue abatement after lead paint removal. Consult the relevant authorities on regulations, requirements and approvals prior to use for this purpose. For smaller areas or spot, cleaning try Selleys Super Kleen Safety tips For stubborn, in-ground stains use neat with a safe scouring cloth – a Selleys Wash Up Wiz is ideal. Avoid contact with skin and eyes. If in eyes, flood with water for 15 minutes. The use of rubber gloves is recommended If swallowed, give a glass of water and see a doctor. If in eyes, wash out immediately with water For advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
$6.00
Selleys Spakfilla Rapid is a ready-mixed lightweight filler that is fast drying, virtually non-shrinking, non-cracking & needs only one application. Features Fill cracks and holes in a single application Pre-mixed and ready to use Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water-based, so can be cleaned up with water Paintable with oil and water-based paints Where can this product be used? Filling cracks and holes on surfaces where no structural movement occurs Filling cracks in walls, ceilings, doors, windows Repairing holes in walls, ceilings, doors and windows What materials is this product suitable for? Wallboard Wood Masonry Plaster Primed nail heads Plasterboard Colours White Technology Water Based Use Interior Exterior (when painted) How To Use Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. Lightly sand back any excess filler from the surface after product dries (30 minutes in thin applications). Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting. Limitations: Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water. Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall. Nailing this product is not recommended. Avoid using below 5°C or in wet conditions. Handy Tips Painting with oil-based paints is not recommended until 24 hours after filler has been applied. Water based paints may be used immediately after filler has set. If filler is found to have stiffened prior to use, stir product. Product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency. Application tools may be cleaned with water. Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen. In exterior applications, protect from rain until dry and painted over with 2 coats of paint. Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry. For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times. Keep container closed when not in use. Clean Up Uncured product may be removed with water. Cured product can be removed by scraping or sanding.
$20.00
Key Features Fill cracks and holes in a single application Pre-mixed and ready to use Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water based, so can be cleaned up with water Paintable with oil and water based paints
$15.00
Selleys Spakfilla Coloursmart is a ready-mixed, lightweight filler which contains a dry time indicator that goes on pink and dries off-white, taking the guesswork out of knowing when to sand & paint! Features Fills cracks and holes in a single application Pre-mixed and ready to use Goes on pink and dries off-white when ready to sand Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water based, so can be cleaned up with water Paintable with oil and water based paints Where can this product be used? Filling cracks and holes on surfaces where no structural movement occurs Filling cracks in walls, ceilings, doors, windows Repairing holes in walls, ceilings, doors and windows What materials is this product suitable for? Plaster Wallboard Wood Plasterboard Masonry Fibrous cement Primed nail heads Size 180g Tub Colours Pink, dries off white Technology Water Based Use Interior Exterior Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. Lightly sand back any excess filler from the surface after product turns off-white (2 hours for holes up to 2mm deep). If more than 2mm deep, or in cold and humid conditions, expect longer drying times. Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting. Limitations: Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water. Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall. Nailing this product is not recommended. Avoid using below 5°C or in wet conditions.
$18.00
A strong, weather and impact resistant adhesive that is ideal for most shoe repairs. Features Easy to use Strong Flexible Bond Weather resistant Impact resistant Appearance Dries yellowish/beige Where can this product be used? Sole Tongue Strap Inner sole Attach beads, jewels, decorative items Will not bond Polyethylene or Polypropylene plastics. For these we recommend Selleys Plastics Glue. May not adhere to some plastic / rubber soles. What materials is this product suitable for? Leather Canvas Fabric Rubber Cork Most Plastics EVA foam (e.g Desert boots sole) How to use this product Ensure surfaces are clean, dry and free from dirt or grease. Remove cap and carefully pierce seal. For larger area repairs such as shoe soles, we recommend you use the contact bond method: For quick and even bonding, apply to one surface only, press together and pull apart. Keep apart until the adhesive film is almost dry (approx. 10 – 20 minutes). Carefully line up surfaces to be joined and press surfaces firmly together. Bonds immediately on contact. Clamping may be necessary in some applications. For smaller areas, either use the contact method as above, or join with a wet bond: Apply Shoe Glue to one surface only and immediately press together. Lightly clamp or hold until dry. Allow adhesive to achieve maximum bond strength (24 hours) before wearing your repaired shoe/s. Wipe nozzle clean and replace cap immediately after use. Clean up application tools and excess adhesive with turps before it dries. Handy tips A piece of plastic from a takeaway container makes a good applicator for shoe soles. Bulldog clips are handy to use for clamping straps and other small areas. Pack includes a removable nozzle for easy application.
$6.00
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$19.12
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$9.00
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$5.00
A specially formulated adhesive and primer system that delivers a strong and shock-resistant bond on all plastics*, even polyethylene, polypropylene & ABS. Features Strong bond on all plastics*, even difficult rigid plastics like polyethylene, polypropylene & ABS Shock resistant, giving you a longer-lasting fix Fast setting in 30 seconds Also bonds plastic to non-plastic materials such as metals, timber, china, rubber, leather, and paper *Does not work on PTFE (Teflon) Where can this product be used? To repair plastic items made of PP, PE and ABS, e.g. plastic toys, office items, remote control What materials is this product suitable for? ALL plastics* including polyethylene, polypropylene and ABS Metals Timber China Rubber Leather Paper How to Use Use the primer pen to apply one coat on each plastic surface to be bonded. Primer pen will appear clear on the surface. Pierce seal at end of the adhesive tube by attaching nozzle & cap and turning clockwise. Remove cap and apply a small amount of glue to one surface only. Limitations: Not suitable for glass or foam, use Selleys Araldite Ultra Clear for glass or Selleys Power Grip Original for polystyrene foam. Product only works on some rubbers and will not work on PTFE. May cause leather to harden or discolour, test on an inconspicuous area first.
$10.29
Selleys Paint Over Sealant is a permanently paintable sealant. Features Paintable Smooth flawless finish. Easy to use and can be used on damp surfaces. Superior adhesion to most building materials. Low odour so can be used in any environment without discomfort. Weather resistant by forming a durable seal which remains flexible, not drying or cracking Superior flexibility +/- 25% movement capability & up to 800% elongation or stretch. Temperature resistance – approximately -40°C +93°C Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. May be discoloured by contact with alloys containing brass, copper or zinc. Do not allow unused product to freeze. Where can this product be used? 10879.Window frames that need painting 102879.Capstones Masonry walls that need painting Perfect for use on or around: Bricks and concrete Windows frames Tiled and wooden fixtures Areas where a sealant is needed and where you want to paint it Not suitable for use in below waterline applications. Not suitable for use on oily woods such as cypress, teak or cedar. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Fibre Cement Painted Surfaces Ceramics Masonry Most metals Most plastics Wood How to use this product Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of sealant. Remove the tape before the sealant skins. For a better finish use a spatula dipped in detergent and water to tool off the sealant. Allow the surfaces to skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water based under coats & flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. To improve the paint finish, wipe the sealant with detergent solution immediately before painting. Avoid smearing sealant on the surrounding surfaces as this may effects its paintability. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin. Avoid breathing in vapours. Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use keep the nozzle on the cartridge Silicone is a reactive product and is designed to cure once exposed to air. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$25.00
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$13.00
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/121994701b5c42c1bd5e5c839bcfcd4e.jpg?v=1757753039&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary FeaturesSuperior formulation+ that stops mould growth*Fast skinning formulation which means you can use your shower in 1 hourProvides a durable waterproof sealResists lifting Where can this product be used?Suitable for use in humid and damp environments such asKitchensBathroomsLaundriesShowersBasinstilesWorktopsBaths & spasPlumbing fixtures What materials is this product suitable for?CeramicGlazed & porcelain fixturesAluminiumPlastic laminatesSome rubbersGlassStainless Steel How to UseBefore applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mouldThoroughly clean surface where sealant will be applied with turps and dry completelyCut nozzle at 45°angle, cut cartridge tip and fit nozzlePlace in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the jointTool with a spatula dipped in detergent water within 5-10 minutes of applicationClean up with turps before product skins Limitations: +Compared to Selleys Wet Area#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growthNot suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility TipsFor neater joints, mask sides before applying the sealant and remove the tape before sealant skinsNot paintable. Complete painting 7 days before applying the sealant
$21.93
![Selleys No More Gaps Timber Floors x 380g [Walnut]](http://gluesaustralia.com.au/cdn/shop/files/169e8e96732544d89fdb6ec6deaba129.jpg?v=1757753052&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
![Selleys No More Gaps Timber Floors x 380g [Jarrah]](http://gluesaustralia.com.au/cdn/shop/files/42b566f39b234ffeab320faed408b86e.jpg?v=1757753057&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
![Selleys No More Gaps Timber Floors x 380g [Hardwood]](http://gluesaustralia.com.au/cdn/shop/files/5160e944b5d3493cbac2a999232381fa.jpg?v=1757753063&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
Selleys No More Gaps Interior Colours is a flexible gap filler available in a range of modern colours, to fill those unsightly gaps and cracks around the home and take away the need to paint. Features Available in a great colour range, so no need to paint. Paintable if required. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for long. Has greater than 350% elongation/stretch and up to +/- 20% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage Can be painted over with both water and oil-based paints, after the surface has skinned. (Approximately 30 minutes after application). Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack Is formulated for long term resistance to cracking and crumbling. Is water-based, so can be cleaned up with water. Will not stain building materials. Has good resistance to weathering. Mould and mildew resistance. Where can this product be used? Between window and door frames and the wall. Along skirting boards. Around cornices. Between benchtops and tiles which are not exposed to water. In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm. What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Bare or painted surfaces Colorbond Many other building materials How To Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut the seal and nozzle and fit to the top of the cartridge. Insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun. Hold the caulking gun at a 45° angle and apply, forcing product into gap Smooth with a wet finger or spatula Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow surface to skin thoroughly prior to painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured. Avoid water contact until fully cured- 72 hours or longer in cold weather. Limitations: Not recommended for foot traffic areas, gaps between tongue and groove boards or weatherboard overlaps. Use Selleys(R) No More Gaps(R) Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards. Use Selleys(R) No More Gaps(R) Exterior & Weatherboard Gap Filler for weatherboard overlaps. Not suitable for areas in prolonged contact with water eg. showers, pools & spas. Where significant joint movement occurs, or for areas of frequent water immersion, use the appropriate Selleys(R) Silicone Sealant. Do not apply or store below 5°C. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying the product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. Allow the surfaces to the skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water-based undercoats and flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. Keep a pack of Selleys Sugar Soap Wipe handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$15.00
![Selleys No More Gaps Filler Sealant Fast Dry [White]](http://gluesaustralia.com.au/cdn/shop/files/da7575e6045648c8aee7c9769b69a8cc.jpg?v=1757753086&width=645)
Selleys No More Gaps Fast Dry has been designed to be painted over in just 20 minutes so that you can finish the job sooner! No More Gaps Fast Dry also provides superior crack resistance with high flexibility and low shrinkage. Features Paint over in 20 minutes* Superior crack resistance Superior adhesion to a broad range of surfaces, resulting in a lasting finish A smooth flawless finish and minimal shrinkage Can be cleaned up easily and quickly with water Will not stain building materials Can be used indoors and outdoors *Allow longer drying times before painting with flat or ceiling paints or in cooler weather. Where can this product be used? Architraves Skirting boards Cornices Window and door frames Wall joints What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Painted surfaces Many other building materials How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into caulking gun such as Selleys Light Speed Caulking gun. Apply with caulking gun, forcing product into gap. For a smooth finish, smooth with a finger dipped in water. For a professional finish use a paint scraper such as a 50mm Soft Grip Scraper. Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow to skin (about 20 minutes) before painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured. Limitations: For gaps between tongue and groove boards and weatherboards use No More Gaps® Exterior & Weatherboard. Where movement is excessive or for areas where contact with water is frequent, use the appropriate Selleys® Silicone Sealant. Handy Tips To avoid paint cracking, apply at temperatures above 10°C and do not apply paint too thick. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler, and a perfect finish. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. Allow the surfaces to skin prior to painting, which is approximately 20 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water based under coats and flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. For exterior applications protect from rain until firmly skinned. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$6.00
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$11.00
![Selleys No More Gaps Coloured Caulk Sealant 450g [Tranquil Retreat]](http://gluesaustralia.com.au/cdn/shop/files/18cfd18e466f43bab8a6fd2d1eaf4bfd.jpg?v=1757753110&width=645)
$15.00
![Selleys No More Gaps Coloured Caulk Sealant 450g [Timeless Grey]](http://gluesaustralia.com.au/cdn/shop/files/047808da6e434754b1b4b492e02434e9.jpg?v=1757753116&width=645)
$15.00
![Selleys No More Gaps Bricks Mortar [Sandstone]](http://gluesaustralia.com.au/cdn/shop/files/9300697130297_4ba0669c-67f5-40d4-9f47-db82307f921f.png?v=1754711842&width=645)
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C. Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$24.79
![Selleys No More Gaps Bricks Mortar [Off White]](http://gluesaustralia.com.au/cdn/shop/files/9300697130334_5a88883c-9e8a-4c25-80f6-535ba26ac80d.png?v=1754711844&width=645)
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C. Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$22.93
![Selleys No More Gaps Bricks Mortar [Medium Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697130327_41339ef1-92ff-417a-bab1-8529f0ee07f6.png?v=1754711845&width=645)
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C. Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$22.93
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Also available in easy tube format. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces How to Use Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$9.00
SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to response to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces
$8.00
Selleys Liquid Nails Rapid Cure is an advanced, high-performance polyurethane construction adhesive that cures in just 10 minutes*. It provides a durable, waterproof bond even when bonding two non-porous surfaces. Features Fast cure in 10 minutes*. More than twice the strength of conventional solvent-based construction adhesives. Waterproof – Uncompromising durability, with excellent water, weather and heat resistance. Can be used to bond most materials, and for most interior & exterior applications. Its advanced formulation exceeds the requirements of BS-EN204 D4 for durability. Resistant (after full cure) to heat to 100 degrees C and cold to -30 degrees C. See “Limitations” below. Does not drip, sag or string between panels. Bridges gap up to 5mm hence can be used on rough and ill-fitting construction materials. Product expands slightly as it cures. The dried adhesive is paintable. *Expect longer times for very dry timber, heavier objects and less porous surfaces or in colder weather. *Limitations – Not suitable for sole fixing or structural bonding. Where can this product be used? Liquid Nails Rapid Cure can be used for applications where higher performance characteristics are necessary. These include applications where: Extra water resistance is essential. eg. Exterior applications such as decking. Extra strength is required. Extra temperature resistance is required. eg. Applications where metal substrates are exposed to direct sunlight. Plastic substrates which are sensitive to solvent-based adhesives are used. Metal installations in which solvent-based adhesives will be slow to cure. Liquid Nails Waterproof is also suitable for typical construction applications such as: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite What materials is this product suitable for? Timber MDF Plasterboard Plastics (Pre-test to determine suitability) Masonry Concrete Particleboard Metals Rubber Tiles LOSP treated pine How to use this product General Avoid contact with skin. Wear safety glasses, impervious gloves and clothing. Surfaces to be bonded should be free of oil, grease and dust. On wet timber pooled water should be wiped off. 1. Cut cartridge tip, fit nozzle and cut end to desired width (approx 5mm diameter). 2. Apply bead along the length of one bonding surface. On broad surfaces apply beads every 40cm. (‘zig-zag’ beads are more appropriate on surfaces of moderate width; eg shiplap panels.) 3. Position pieces and press firmly together. Fix with sufficient nails, screws or clamping to hold the load and achieve contact over the total bond area. Repositionable for up to 5 mins after fitting. 4. Allow to set for 15-20 mins for porous surfaces before removing temporary fasteners or clamps.* Liquid Nails Rapid Cure will achieve a full cure in 24 hours. *Expect longer times for very “dry” timber, heavier objects and less porous surfaces, or in colder weather. Spraying surfaces with a very light mist of water may help speed up the cure. Handy tips Gloves should be worn when applying Liquid Nails Rapid Cure. Avoid contact with skin. Adhesive requires moisture to cure, therefore drying times will vary depending on temperature, humidity and the porosity of materials bonded. Spraying surfaces with a very light mist of water may help speed up the cure. The product should not be applied below 5°C. LIQUID NAILS Rapid Cure expands slightly as it cures. Not suitable for sole fixing for structural bonding. LIQUID NAILS Rapid Cure should always be used in conjunction with mechanical fasteners in structural, critical or high-stress applications. Wet LIQUID NAILS Rapid Cure residues can be removed with acetone or mineral turpentine. Cured or dry LIQUID NAILS Rapid Cure residues can be removed by chiselling, scraping or sanding. Safety tips If swallowed, do NOT induce vomiting. Avoid skin contact. Avoid breathing in vapours. Ensure you use a well-ventilated area The product is an eye, skin and respiratory irritant and can potentially cause irritation. Avoid contamination of waterways. Allow waste or leftover product to completely dry out before disposing of it. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in a cool place. The adhesive should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Liquid Nails Rapid Cure is a polyurethane based adhesive that requires moisture to cure. Wrapping the nozzle in aluminium foil and sealing tightly with tape can prevent moisture exposure for longer storage.
$17.00
Liquid Nails Clear eliminates unsightly mess caused by conventional brown construction adhesives because it dries clear and blends with the surrounding surface. It is ideal where a fine finish is important. Uses Selleys Liquid Nails Clear is suitable for bonding to glass, fibreglass, metals, most plastics*, timber, particleboard, MDF, tiles & ceramics, concrete, painted and masonry substrates. Suitable for bonding mouldings & trims, skirting boards & architraves, general fabrication and creating mosaics. Pre-test plastics to determine compatibility. Technical Features High performance solvent based adhesive. Note: When use on glass to glass, thin film application is recommended for better clarity. Good paintability – Paintable with water based paints. Oil based paints require undercoating with water based paints first. Excellent resistance to water and weather makes it suitable for interior and exterior applications. Application Tips Due to solvent content Liquid Nails Clear should not be used in enclosed space or without ventilation Solvents may affect some plastics Will not bond polyolefin plastics such as polyethylene and polypropylene May damage some polycarbonate, avoid smears and spills Cannot be used on polystyrene foam May not adhere to wet absorbent surfaces or to some old wet metals In very cold weather cartridge must be conditioned to room temperature before use Not recommended for permanent water immersion or water containment structures Must be first painted with water based paint prior to painting with oil based paints Will not accept common wood stains. (If staining is required, it is recommended to stain timber before bonding). Full cure in 2 weeks Not recommended for mirrors Bonds weaken at high temperatures. Avoid bonding metals or heavy materials which will be heated by direct sun. (Consult Selleys about particular applications subject to heating). Ensure that surfaces are free from dust, loose particles and dry. Cut cartridge tip, pierce membrane inside base of nub, fit nozzle and cut end to desired opening and fit cartridge into cartridge gun. In very cold weather, cartridge may need to be conditioned to room temperature for easier gunning. Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. (“zig-zag” beads are more appropriate on surfaces of moderate width) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are re-positionable for up to 20 mins after fitting Allow adhesives to set (at least 24 – 48 hours) before removing any temporary fasteners or clamping. (refer to Bond strength Time) For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-3 minutes before firmly Technical Details and Performance Time for strong bond depends on nature and condition of application. A minimum of 24 to 48 hours is needed for sufficient strength to develop. The bond will continue to strengthen over time. Full cure up to 14 days. Curing is achieved by evaporation of solvent. Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (e.g. metals and glass). Indicative information only, not to be used for setting specifications. Appearance Clear soft adhesive Viscosity 5000 – 9000P TE/2 @ 25oC HAF/HELIPATH Skin Time / Tack Free Time 5 min. @ 25oC Specific Gravity 0.87g/mL Extrudability 100g/min. @ 25oC (at 628kPa pressure through 3mm orifice) Solid Content 60% Cure By evaporation of solvent Water Based Paints Good Alkyd Paints Good, after first undercoating with a water based paint Flammability Uncured adhesive- flammable Cured adhesive – will burn if ignited Service Temperature Maximum 80oC Coverage 15 metres of a 5mm diameter bead Cleaning Clean off wet adhesive with mineral turps or white spirit. Dry adhesive can be removed by scraping or sanding.
$13.00
Selleys KwikGrip Spray 350g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces Adhesive Mastery: Quick, Clear & Heat Resistant Discover the power of Selleys KwikGrip Spray 350g, a versatile adhesive spray that bonds instantly on contact. Ideal for both absorbent and non-absorbent surfaces, it offers a quick-drying and heat-resistant solution for a multitude of projects. Key Features: Versatile adhesive spray Durable bond Fast drying and dries clear Heat resistance up to 70°C Common Applications: Car upholstery repairs Fixing laminate on tables and bench tops Patching vinyl flooring Art and craft projects And many more... Compatible Materials: Laminated plastics Timber Craft foam Aluminium Leather Canvas Rubber Most plastics* How to Use: USE ONLY IN A WELL VENTILATED AREA. Shake the can well. Ensure surfaces are clean and dry. Hold the can 20cm away and spray surfaces evenly. For a permanent bond, spray both surfaces and wait until touch dry before pressing together. Clamp overnight for a firm bond. For a temporary bond, spray one surface and press together while still tacky. Limitations: Not suitable for bonding rough, ill-fitting surfaces or certain plastics like polyethylene or polypropylene. Refer to the guidelines for alternative solutions. Handy Tips: After use, clean the nozzle by inverting the can and spraying until clear
$21.00
A versatile hand kneadable, fast setting, non-rusting co-extruded epoxy repair system that can be used for repairing ferrous and aluminium metal items. It comes in a handy roll form, with the black hardener encapsulated in the grey resin part. The product hardens in 5-10 minutes, after mixing, to a black metal-like material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under water (but dry surfaces for application are best and recommended). Rapid Set (less than 10 minutes). Can be used for fuel resistant repairs. Appearance Dries Dark Grey/Charcoal Where can this product be used? Rebuilding engine parts and rusted metal etc Repairing a hole in a fuel tank Repair of iron pipes, tools and equipment Repair stripped threads Forming of nuts and bolts in place Attaching fixtures and signs Fixing radiators Repairing holes in cars and boats Patching ducts and tanks Making prototypes Thread locking Repair of down pipes and gutters Anchoring of bolts Repairing your metal outdoor furniture Set time increases at temperatures below 20°C Not recommended for plastic fuel tanks Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Not tested for drinking water contact to AS/NZ 4020:2005 What materials is this product suitable for? Steel Wide range of terrous metal and aluminium items Most plastics (pre-test required) Glass How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning Cut off required amount. Replace disc on remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to uniform colour. If mixing is difficult, warm to room temperature. Apply with pressure to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Steel will harden and begin to form a strong bond. After 60 minutes Knead-It Steel may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour, and feel a mild heat radiating from thre knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Store in a cool place for maximum shelf life Use Knead-It Multi Purpous for applications in contact with drinking water. Use Knead-It Aqua for applications in wet/submerged areas. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Steel. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$26.00
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$13.00
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$26.00
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$13.00
Features Simply sticks almost anything without screws or clamps* Instantly holds even on vertical surfaces* Adjustable for up to 15 minutes UV & water-resistant Holds up to 360kg/ m² Where can this product be used? Indoors and outdoors for any bonding applications What materials is this product suitable for? Glass Metals Timber Brick Concrete / masonry Tiles Not for polyethylene, polypropylene or teflon Colours White Technology Sil-X® Use Interior Exterior How to use Make sure surfaces are clean, free from grease, girt and grime. Sand back any loose or peeling surfaces. Pull off cap, unscrew nozzle and pierce membrane with the tip of the nozzle. Replace nozzle and cut along the second ridge. Cover one surface in the adhesive in long vertical strips. After applying the adhesive, press surfaces together firmly, ensuring the adhesive spreads. Clean up any excess product with methylated spirits.
$16.00
Features Simply sticks almost anything without screws or clamps* Instantly holds even on vertical surfaces* Adjustable for up to 15 minutes UV & water-resistant Holds up to 360kg/ m² Where can this product be used? Indoors and outdoors for any bonding applications What materials is this product suitable for? Glass Metals Timber Brick Concrete / masonry Tiles Not for polyethylene, polypropylene or teflon Colours White Technology Sil-X® Use Interior Exterior How to use Make sure surfaces are clean, free from grease, girt and grime. Sand back any loose or peeling surfaces. Pull off cap, unscrew nozzle and pierce membrane with the tip of the nozzle. Replace nozzle and cut along the second ridge. Cover one surface in the adhesive in long vertical strips. After applying the adhesive, press surfaces together firmly, ensuring the adhesive spreads. Clean up any excess product with methylated spirits.
$13.00
Liquid Nails Fast is a water-based high strength (*) construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. After drying it is beige (light tan) in colour. Uses Liquid Nails Fast has high initial (immediate) grab which reduces the need to support joins while the adhesive cures. The initial grab works best with porous surfaces. It will bond to many building materials including MDF, particle board, timber, plaster board, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results are achieved when at least one surface is porous. Liquid Nails Fast would typically be used for the following applications: Areas where nailing is not desirable Skirting boards, architraves, cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding minimises slippage when adhering on vertical surfaces Meets or exceeds AS 2329-1999 (Mastic adhesives for fixing wall boards) Does not drip, sag or string between panels Bridges gaps and will adhere materials with uneven surfaces Low mess – excess and squeeze out is easily cleaned up with wet cloth No solvent fumes – ideal for large indoor jobs High flexibility – will withstand thermal movement and vibration High heat resistance – will not lose bonds exposed to sun Paintable when dry Easy to extrude at all temperatures Application Tips Liquid Nails Fast should always be used in conjunction with permanent mechanical fasteners except in low stress applications such as wall panelling and fixing light weight objects. (Bonds may creep under constant heavy loads.) Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications. In cold or damp weather and between non-porous materials drying time is greatly extended Thick applications take longer to dry than thin applications Pre-test plastics to determine suitable bonding. Adheres well to UPVC. Not suitable for polyethylene and polypropylene. For wood flooring applications Liquid Nails (solvent based) is recommended. [Liquid Nails Fast is satisfactory for fixing sheet flooring (particleboard/ply) to joists in conjunction with the manufacturer’s minimum nailing specification but is not recommended for fixing sheet wood flooring to flat surfaces such as existing or concrete floors. Technical Details and Performance For porous substrates good bond strength is achieved after 24 hours and will continue to strengthen over 2-3 day period. Time for strong bond depends on nature and conditions of application. In cold or damp weather and between non-porous materials, drying time is greatly extended. Indicative information only, not to be used for setting specifications. Appearance Lump free, air-free smooth beige paste Specific Gravity Approx. 1.44g/mL @ 25oC Viscosity Typical 7000 – 9000 Poise Slump Typical: 0mm Shear Adhesion Strength (7 days) (AS2329) Greater than 1500kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure) Typical 40N/25mm (wire gauze off hoop pine.(Variant to AS2329)) Initial Bond Strength AS2329-1999D (Tested after 24 hrs) Over 200kPa Heat Resistance Bonds will resist temporary exposure to temperatures up to 140oC. Constant high temperatures will reduce constant load holding power (see below). Creep resistance (under constant load)*2 Fully cured *1 bonds of 625 sq. mm will hold up to 500g loads (7.8kPa) in shear at constant 80oC Fully cured *1 bonds of 625 sq.mm will hold up to 100kPa in shear at 25oC (equivalent to 6Kg load on 625 sq.mm bond area) Coverage 15 metres of a 5mm diameter bead 1mm thick bonds on porous substrates cured at least 7 days at temps above 25oC This data is provided as indicative only. Not to be used for design purposes. Thick bonds reduce constant load holding power and increase curing time. Larger bond areas increase curing time. Cleaning Liquid Nails Fast may be cleaned off with hot soapy water or a damp cloth while still wet. Dry adhesive is best removed by scraping or peeling.
$14.69
Selleys Ezy Glide: The Dry Lubricant Solution for Any Surface, Anywhere No More Squeaks, No More Sticking: All-Surface Dry Lubricant Introducing Selleys Ezy Glide, a dry, non-oily lubricant that offers long-lasting lubrication while avoiding dirt and dust accumulation. Designed for a multitude of surfaces, it's your go-to for making things glide effortlessly. Key Features: Contains a dry lubricant (PTFE) Dries clear Long-lasting lubrication Does not attract dirt and dust Non-oily lubricant Applications Include: Windows Drawers Zipper Doors Locks Indoor/Outdoor Furniture Roller Door Tracks Curtain Tracks Sailboat Runners Children's Toys Sliding Glass Doors and Mirrors Suitable Materials: Wood Metal Leather Other Absorbent Surfaces How to Use: Shake the 150g aerosol can well. Hold the can approximately 80-100 mm (3-4") from the surface and spray lightly. Allow a few minutes for drying. Limitations & Tips: Ezy Glide may not be compatible with some materials like plastics, and it produces a slippery coating. Test in an inconspicuous area first and avoid over-spraying onto floors. Use the extension tube for hard-to-reach areas. Ezy Glide does not contain silicone. Avoid overspraying on fabric as it may mark the material.
$15.00
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before the adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High-Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many kinds of wood. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be softened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$6.00
The Selleys 3-in-1 Adhesive, Sealant & Gap Filler is your ultimate all-in-one solution for a wide range of DIY and professional applications. This versatile product combines the power of a strong adhesive, the reliability of a waterproof sealant, and the precision of a gap filler, all in one easy-to-use formula. Whether you're tackling home repairs, sealing joints, or filling cracks, Selleys 3-in-1 ensures a durable, flexible, and weather-resistant finish. Perfect for both indoor and outdoor use, it adheres to a variety of surfaces including wood, metal, glass, and ceramics. With Selleys 3-in-1, you can trust in a product that delivers exceptional results every time, simplifying your projects and saving you time and effort Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material damp or dry,inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water based paints. Limitations: Not recommended for solvent based paints. If required, paint with a water based paint first. Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Size: 480g Cartridge Colour: White Technology Sil-X® Use: Interior & Exterior
$19.00
Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Easy-to-apply design with no mess or tools. Use instead of nails and screws Specifications Brand Scotch-Mount™ Overall Width (Metric) 2.54 cm Product Colour White Details Scotch™ Indoor Double-Sided Mounting Tape is ideal for painted surfaces and allows you to quickly and easily beautify and organise your space. Whether you’re creating a gallery wall or affixing the family chore chart, this permanent double-sided foam tape delivers a strong bond every time because of its 3M™ industrial strength adhesive. Your work is up and ready to admire in 30 seconds flat – no nails or hammer needed. Never let how you’re going to hang it get in the way of your creativity with the powerful adhesion of Scotch™ Indoor Double- Sided Mounting Tape. Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Easy-to-apply design with no mess or tools. Use instead of nails and screws Great for do-it-yourself projects
$15.99
Holds up to 4.5kg, 22cm holds 1kg Mount organisational caddies in the home office or kitchen, chalkboards, decorative signs or plaques Ideal for indoor use only, no need for nails and screws Double coated foam tape that isflexible, soft and conformable Specifications Brand Scotch™ Indoor/Outdoor Indoor Overall Length (Metric) 1.3 cm Overall Width (Metric) 2.5 cm Product Colour White Product Type Rolls Size 2.5cm x 1.3m Details Scotch™ Indoor Mounting Tape makes it so easy to beautify and organise your space quickly and easily. Whether you're creating a gallery wall or affixing the family chore chart, this permanent double-sided foam tape delivers a strong bond every time. Your work is up and ready to admire, no nails or hammer required. Never let how you're going to hang it get in the way of your creativity with the powerful adhesion of Scotch™ Indoor Mounting Tape.
$9.50
Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Specifications Brand Scotch™ Indoor/Outdoor Indoor Product Type Mounting Strip Details This virtually invisible, professional-quality tape is designed for attaching items up to 4.5kg to any smooth wall or surface. It is perfect for discretely mounting items on glass, tile or mirrors. For items that need an undetectable mounting means, reach for the stealth adhering power of Scotch™ Clear Mounting Tape. Virtually clear, this double sided permanent tape is perfect for mounting glass, tiles and artwork. Its strong bond holds up to 15 pounds, without the hassle of nails or a hammer. So whether you're mounting acrylic cosmetic organisers or a translucent picture frame, affix it confidently with Scotch™ Clear Mounting Tape. Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Ideal for use on glass, metal, tile, plastic and more Intended for indoor and outdoor use Ensure your surface is smooth, clean and dry for the best bond Made in the USA from domestic and globally-sourced materials UV resistant colour: Clear
$14.24
Holds up to 1.8kg, 2.5cm holds 113g, 10cm holds 453g Mount organisational caddies in the home office or kitchen, chalkboards, decorative signs or plaques Ideal for indoor use only, no need for nails and screws Double coated foam tape that isflexible, soft and conformable Specifications Brand Scotch™ Good For Outdoors No Indoor/Outdoor Indoor Overall Length (Metric) 2.5 cm Overall Width (Metric) 2.5 cm Product Colour White Product Type Squares Size 2.5cm x 2.5cm Details Scotch® Indoor Mounting Tape makes it so easy to beautify and organise your space quickly and easily. Whether you're creating a gallery wall or affixing the family chore chart, this permanent double-sided foam tape delivers a strong bond every time. Your work is up and ready to admire, no nails or hammer required. Never let how you're going to hang it get in the way of your creativity with the powerful adhesion of Scotch® Indoor Mounting Tape. Scotch® is the permanent mounting solution that is fast, easy and does not require the need for any tools. Holds up to 1.8kg, 2.5cm holds 113g, 10cm holds 453g Mount organisational caddies in the home office or kitchen, chalkboards, decorative signs or plaques Ideal for indoor use only, no need for nails and screws Double coated foam tape that isflexible, soft and conformable Bonds to any smooth, indoor surface Faster, safer, and more versatile than screws and nails Ideal for Indoor use on any smooth surface No need for any tools, nails or screws
$9.96
![Scotch 3M Mount Double Sided Squares Indoor 15lb x 48 [2.54cm x 2.54cm]](http://gluesaustralia.com.au/cdn/shop/files/051131769960N_f18dde17-9448-4437-aace-df5695c465e8.jpg?v=1754711993&width=645)
Scotch Indoor Double-Sided Mounting Squares are ideal for painted surfaces and allow you to quickly and easily beautify and organize your space. Whether you’re creating a gallery wall or affixing the family chore chart, these permanent double-sided foam squares hold up to 15 pounds and deliver a strong bond every time because of their 3M™ industrial strength adhesive. Your work is up and ready to admire in 30 seconds flat – no nails or hammer needed. Never let how you’re going to hang it get in the way of your creativity with the powerful adhesion of Scotch Indoor Double- Sided Mounting Squares. Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 3 squares To hold 15 lb use 45 squares Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in the USA with Globally Sourced Materials Color: White Specifications Size (Imperial) 0.5 in x 0.5 in, 1 in x 1 in
$8.89
Scotch Indoor Double-Sided Mounting Tape is ideal for painted surfaces and allows you to quickly and easily beautify and organize your space. Whether you’re creating a gallery wall or affixing the family chore chart, this permanent double-sided foam tape holds up to 15 pounds and delivers a strong bond every time because of its 3M™ industrial strength adhesive. Your work is up and ready to admire in 30 seconds flat – no nails or hammer needed. Never let how you’re going to hang it get in the way of your creativity with the powerful adhesion of Scotch Indoor Double- Sided Mounting Tape. Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 3" To hold 15 lb use 45" Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in the USA with Globally Sourced Materials Color: White
$9.27
You have seen 432 out of 657 products
Easy-to-use, low-odour products with straightforward instructions and tidy finishes—great for home fixes and craft. Prefer water clean-up and clear-drying where appearance matters. Use filters to refine by chemistry and set speed. Always review the product page and TDS/SDS.
