In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A flexible multipurpose gap filler, to fill gaps around cornice, wall joints, skirting board, window and door frames where where movement causes ordinary fillers to crack or fall out.
For use on: Wood, brick, aluminium, glass, plasterboard, ceramic
tiles and painted surfaces (INTERIOR & EXTERIOR)
Coverage: 30m/3mm bead.
Dry time: Skins in 30 minutes at 25°C. Full cure in 7days.
Ready to use: YES
Available in: 475g
Colour: White
NOTE: Not for fine joints between tongue and groove boards or weatherboard overlaps.
• Ensure surfaces are clean, dry and free from oil, dust, grease, flaking paint and old sealant.
• Using caulking gun, push sealant ahead of nozzle forcing it onto the surface and into the joint. Ensure the sealant is touching both sides of the gap.
• Smooth with wet finger or knife and remove excess sealant immediately with a damp cloth.
• Allow sealant to skin approx 30 min before painting with water-based paints.
• Allow to set for 48 hours if using oil based paint or if joint is large.
• Some water-based undercoats and flat paints may crack on drying. Test a small section of sealant. Paint cracking may be reduced by using a vinyl/ acrylic semi glossed paint or oil based undercoats first, or by allowing the sealant to cure thoroughly before painting.
• Do not use outside if rain is imminent, not for contantly damp areas.
• Painting improves exterior durability.
• Use Poly silicone sealants for a watertight seal or where movement is excessive.
• Water clean up
Q. How do I fill gaps between my wooden window frames and inside wall?
A. You're dealing with two different materials here, plaster and wood. To allow for differential movement between them, use Polyfilla Gap Filler, wiping off any excess with a damp cloth.
Q. I painted over the areas where I used Polyfilla Gap Filler and now cracks have appeared. Why has this happened?
A. If the gap filler was not cured sufficiently before it was painted over, cracks can occur as the gap filler shrinks. To prevent this, allow 48 hours drying time when you are filling large gaps or painting with oil-based paints. Also, some water based undercoats and paints shrink during drying and as Polyfilla Gap Filler is flexible, it won't stop cracks appearing in the shrinking paint on its surface. Test the paint on a small section of gap filler and if this is a problem you can reduce cracking by allowing the filler to cure thoroughly or by first coating it with a vinyl/acrylic semi-gloss or oil-based undercoat.
Q. Why does my gap filler keeps cracking?
A. It is important to remember that the width of a gap affects how much the product can move. Fine cracks less than 2mm allow the gap filler to move only very tiny amounts before it may crack again. It is best to ensure that you have at least 3mm worth of product so you can maximise the movement capability of your joint.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Interior and exterior use
Acetic cure
Excellent bond to glass
Parfix Window & Glass Silicone is suitable for use on windows, glass partitions and glass blocks.
Ideal for both interior and exterior use, Parfix Window & Glass Silicone is an acetic cure silicone with that bonds securely to glass, providing a water tight and UV resistant seal.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Can be used on both interior and exterior substrates
Highly flexible
Non-corrosive
Neutral cure
Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use.
Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Can be used on both interior and exterior substrates
Highly flexible
Non-corrosive
Neutral cure
Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use.
Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sanitary grade silicone
Acetic cure
Excellent adhesion
Watertight seal
Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sanitary grade silicone
Acetic cure
Excellent adhesion
Watertight seal
Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Parfix Glass Silicone Black: Unmatched Bonding for All Your Glass Needs
Key Features
Excellent bond to glass
Acetic cure for optimal sealing
Designed for interior and exterior use
UV resistant and shrink-proof
Specifications
Colour
Black
Model Name
Parfix Window and Glass 300g
Model Number
9300697122445
Material
Silicone polymer
Paintable
No
Stainable
No
UV Resistant
Yes
Outdoor
Yes
Indoor
Yes
Shrink Resistant
Yes
Sandable
No
Applications
Suitable for use on windows, glass partitions, and glass blocks.
Instructions
For optimal results, apply on clean, dry surfaces. Follow safety guidelines for acetic cure silicones.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Paintable
Flexible
Durable
Parfix Gap Filler is a multi-purpose flexible filler that is suitable for interior applications such as skirting and architraves, door and window frames.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Highly flexible as well as mould and UV resistant, Parfix All Purpose Silicone is suitable for use on shower screens, metal roofing, concrete and gutters.
Highly flexible
Mould and UV resistant
Neutral cure
Non-corrosive
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Flexible Wood Filler repairs small cracks and holes in wood. As the name implies, it is a flexible filling for wood, great for interior and exterior use.
Suitable for all types of interior & exterior wood
Quick drying, easy to sand
Water resistant finish will not shrink, crack or crumble
Stainable and paintable
Properties
Ready for use
Excellent adhesion to all types of wood
Tough and durable fill that flexes with the natural movement of wood
Accepts nails and screws
Sandable and paintable after approx. 3 hours (1 cm layer at 20°C)
Must be overcoated when used outside (minimum 2 coats)
Paintable with all types of paint
Maximum layer thickness: 1 cm
Maximum depth: 2 cm
Colour: natural/pine
How to apply
Substrate must be clean, dry, dust and grease free.
Remove all loose material.
Mix the product well before use.
Product can be applied directly from the pot.
Apply filler firmly into the hole with a filling knife.
For a smooth result, finish with a damp filling knife.
For deeper repairs, build up in layers of 1cm, letting the product dry in between layers.
Once dry, sand the filler so it is even with the surface and dust off. Finish with a stain, varnish or paint. The filler may stain or varnish differently to the surrounding wood.
Clean tools with warm water.
Do not store or use below 5°C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Flexible Wood Filler repairs small cracks and holes in wood. As the name implies, it is a flexible filling for wood, great for interior and exterior use.
Suitable for all types of interior & exterior wood
Quick drying, easy to sand
Water resistant finish will not shrink, crack or crumble
Stainable and paintable
Properties
Ready for use
Excellent adhesion to all types of wood
Tough and durable fill that flexes with the natural movement of wood
Accepts nails and screws
Sandable and paintable after approx. 3 hours (1 cm layer at 20°C)
Must be overcoated when used outside (minimum 2 coats)
Paintable with all types of paint
Maximum layer thickness: 1 cm
Maximum depth: 2 cm
Colour: natural/pine
How to apply
Substrate must be clean, dry, dust and grease free.
Remove all loose material.
Mix the product well before use.
Product can be applied directly from the pot.
Apply filler firmly into the hole with a filling knife.
For a smooth result, finish with a damp filling knife.
For deeper repairs, build up in layers of 1cm, letting the product dry in between layers.
Once dry, sand the filler so it is even with the surface and dust off. Finish with a stain, varnish or paint. The filler may stain or varnish differently to the surrounding wood.
Clean tools with warm water.
Do not store or use below 5°C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on!
Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours.
FEATURES
Premium quality 100% silicone
Ideal for wet areas
Indoor and outdoor use
Maximum flexibility
BENEFITS
Proven to last in all weather
Mould resistant
Tack free in 10 minutes
Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products.
The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use.
In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on!
Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours.
FEATURES
Premium quality 100% silicone
Ideal for wet areas
Indoor and outdoor use
Maximum flexibility
BENEFITS
Proven to last in all weather
Mould resistant
Tack free in 10 minutes
Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products.
The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use.
In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Monarch Mini Roof & Gutter Silicone is a neutral cure silicone sealant that is ideal for repairing or installing gutters, roofs, downpipes, skylights and more. It can also be used to install metal sheets in the roofing industry and various other building services.
With such versatility on offer it's no wonder this product's demand has soared so rapidly! What else would you want from your sealant? Well there are added features like its flexibility and resilience that make it perfect for all applications. You can count on Monarch Mini Roof & Gutter Silicone to stick around because of its long-lasting durability - don't wait until disaster strikes again when you could have had the protection you needed beforehand.
FEATURES
Premium quality 100% silicone
Non-corrosive
Neutral cure
AS 4020 approved
BENEFITS
Quick exposure to light running water
Suitable for use in all weather
UV resistant
Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products.
The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use.
In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Monarch Mini Roof & Gutter Clear Silicone: The Compact Caulking Solution
Product Overview
Designed for roofing and outdoor applications, the Monarch Mini is perfect for a variety of materials like metal, brick, galvanized iron, tiles, and aluminium.
Key Features & Benefits
Quick exposure to light running water
UV resistant for lasting outdoor use
Neutral cure, making it versatile and safe for different materials
Non-corrosive and AS 4020 approved
Compatible with Monarch Mini Compact Caulking Gun
Perfect For
Great for small projects where a full-size cartridge is not needed. Ideal for:
Repairing gutters
Fixing roofs
Mending downpipes
Tight spaces that traditional cartridges can't reach
Colors Available
Available in black and translucent versions for versatility in your projects.
How To Use
Best when used with a Monarch Mini Compact Caulking Gun to reach tight spaces. Always follow the safety guidelines as provided on the product label.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
The unique rubber-infused gel formula allows powerful bonds that are extremely precise even on flexible materials. Ideal for porous and vertical surfaces, and strong enough to withstand extreme conditions. The gel’s high strength non-drip formula then dries transparent to form invisible bonds that give a long lasting durability that is both weather and shock-resistant. For intricate, hard to reach spots, Loctite Power Flex Gel Control features an easy grip squeeze bottle and nozzle for precise applications.
Recommended on:
Rubber, Leather, Wood, Metal, Porcelain, Paper, Plastic.
Properties:
-Rubber infused gel formula for extra strong and flexible bonds
-Ideal for porous and vertical surfaces
-Water resistant
-Bonds in seconds
-Withstands heavy loads
-Dries transparent
-Easy to open, self-piercing and anti-clog cap
-Choice of applicators: convenient tube or easy grip control with a longer nozzle
-Suitable for use on most surfaces*
-Solvent-free
-* Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres.
Step by Step
Ensure surfaces to be joined are clean, completely dry and close fitting.
Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open.
Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set.
Replace the cap immediately and store upright in a cool dry place.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Loctite Extreme Glue No Drip Gel contains a revolutionary Flextec formulation that fuses multiple materials together for a long-lasting bond.
When a project or repair requires an adhesive with a higher viscosity and advanced resistance to extreme conditions, this liquid gel is your new go-to. This versatile, gap-filling glue seals and repairs nearly any surface, and it’s perfect for harsh conditions where constant flexing is a problem. Loctite Extreme Glue No Drip Gel dries clear and minimizes dripping for a clean, professional finish on any household project. It’s even dishwasher safe! Plus, our glue is durable enough to use outdoors because it cures quickly and is resistant to vibration, impact, moisture, UV exposure, and extreme temperatures.
No Drip Gel is great for vertical applications
Withstands vibration, impact, moisture, and UV light
Strong and durable for long-lasting results
Use as an indoor or outdoor glue
Crystal-clear formula for a clean, professional look
Water-resistant and temperature-resistant from -58° to 248° F
Gap-filling gel for imperfect-fitting surfaces
Flexible bond and precise grip
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Kwik Grip Crystal Clear applies clear and dries crystal clear for less mess and invisible bond lines. Excellent for achieving a neat, clear finish when bonding large, flat close-fitting surfaces eg veneers and laminates for bench or table tops. Forms a durable, heat and water-resistant bond.
Features:
Solvent based contact adhesive
Applies clear and dries crystal clear
Strong, durable bond on broad surfaces
Easy to spread
Heat resistant – up to 80°C
Water resistant
Where can this product be used?
Applications where invisible bond lines are needed such as adhering decorative strips to a mirror
Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench or table tops
Patching vinyl flooring
Replacing a vinyl tile
Cork tiling
Laying a vinyl floor
Fixing shoes
Fixing laminate to tables, benchtops etc
Leather shoe and leather repairs, leather work eg handbags
Adhering flexible or other material to Aluminium
Joining, repairing holes in tents, car covers and other outdoor equipment
Seek advice of vinyl flooring manufacturers prior to use with their products as discolouration and bubbling can occur with some types. If in doubt, Kwik Grip Waterbased is safe to use for all these applications and will provide excellent bonding.
Not suitable for bonding rough, ill-fitting surfaces. (Consider the suitability of alternative products such as Liquid Nails for these applications).
What materials is this product suitable for?
Veneers
Rubber
Cork
Felt
Leather
Canvas
Metals
Timber
How to use this product
USE ONLY IN A WELL VENTILATED AREA
Contact Bonding
Hold down lid, whilst opening can.
Ensure surfaces are clean and dry. If cutting laminate sheets, cut slightly oversize. For porous surfaces apply a thin coat to seal surface and allow to dry for approx. 40mins.
Using applicator, completely cover both surfaces with adhesive and keep surfaces apart until ‘touch dry’ – approx 15 minutes, no more than 30 minutes.
Position items carefully, still keeping surfaces apart with dowels. When edges are perfectly aligned, remove dowels, and working from one edge, press surfaces firmly together. Grabs IMMEDIATELY on contact.
Secure the bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block.
Maximum bond strength is reached after 24 hours. Clamping of warped or curled surfaces may be necessary.
Wet Bonding (For small areas or for bonding where one surface is porous)
Ensure surfaces are clean and dry.
Apply KWIK GRIP to one surface, then bring the surfaces together and clamp until dry.
Handy tips
Care should be taken to test plastics prior to use as solvents present will attack some polystyrene and sheet vinyls.
Cover: 500mL covers up to 2.5m2 of one surface, depending on porosity of surfaces.
For vertical surfaces we recommend using SELLEYS Kwik Grip Vertical Gel.
For applications in confined or low ventilation areas eg car interior, we recommend using SELLEYS Kwik Grip Waterbased, as it is non-toxic and free of fumes.
Use a brush, knife or serrated scraper for application.
When using the contact method REMEMBER bonding is immediate once the two surfaces are joined.
Keep container sealed when not in use.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Kwik Grip Crystal Clear has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent.
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Contains highly flammable solvents and care should be taken to ensure all fire precautions are observed. As an alternative, Kwik Grip Waterbased is non-flammable.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gorilla Clear Grip® is a flexible, fast-setting, crystal clear contact adhesive that creates a strong, permanent bond. Gorilla Clear Grip® is paintable and waterproof making it great for projects both inside and out! Build, Repair, Craft™
PRODUCT FEATURES
WATERPROOF – For indoor/outdoor use
FAST GRAB – Holds in just seconds
PERMANENT BOND
FLEXIBLE
CRYSTAL CLEAR
HEAVY DUTY
NO-RUN FORMULA
PAINTABLE
PHOTO SAFE
WASHER & DRYER SAFE
BONDS: Metal, Glass, Fabric, Wood, Ceramic, Leather, Paper, Plastic*, and More!
*Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces.
All surfaces should be clean and free of dirt, grease and oil. Best if used between 10°C and 32.2°C. Clear Grip® should only be used in a well ventilated area.
Apply adhesive to each surface to be bonded.
To maximize bond strength: Wait approximately two minutes for adhesive to partially dry before joining surfaces.
Press surfaces firmly together.
NOTE: Bond forms immediately and can be difficult to reposition.
Cure Time
Allow for a minimum of 24 hours for full cure. Cure time may increase with lower temperatures and when used on non-porous surfaces.
Storage Tips
After each use, wipe nozzle with a dry cloth and tightly replace cap. Store in a cool, dry location. Tip: For easier re-opening, apply a thin coat of petroleum jelly to the threads before replacing cap. Store away from children and animals.
Clean-up
Wipe uncured adhesive with a dry cloth and clean with acetone, isopropyl alcohol, or citrus based solvents according to manufacturer’s instructions. Cured adhesive may be removed by scraping from surface.
Paintable
When fully cured.
*NOTE: Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces.
TECHNICAL SPECS
APPLICATION TEMPERATURE – 10° to 32.2° C, best at room temperature
OUTDOOR – Yes
MOISTURE RESISTANT – Waterproof
PAINTABLE – Yes – Can be painted with water and oil based paints, spray paint
SANDABLE – Yes
STAINABLE – Yes
CURED COLOR – Clear
STORAGE TIPS – Flammable adhesive, do not use or store near heat, sparks, flames, or while smoking. Store in a cool, dry location. Wipe nozzle clean before replacing cap, for easy re-open apply a thin coat of petroleum jelly to threads.
GAP FILLING – No
PHOTO SAFE – Yes
WASHER & DRYER SAFE – Yes
How should Gorilla Clear Grip® be stored?
After each use, wipe nozzle with a dry cloth and tightly replace cap. Store in a cool, dry location. Tip: for easier re-opening, apply a thin coat of petroleum jelly to the threads before replacing cap.
What surfaces does Clear Grip® adhere to?
Gorilla Clear Grip® can be adhered to many surfaces including:
Wood, Metal, Stone, Ceramic, Glass, Plastic*, PVC, Brick, Concrete, Foam, Paper, Rubber, Fabric, and Laminate.
*NOTE: Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces.
Is Gorilla Clear Grip® food safe?
Clear Grip® should not be used around food.
How do you clean up Gorilla Clear Grip®?
When using Clear Grip®, it is best to wear safety glasses and chemical resistant gloves.
To clean uncured adhesive: wipe uncured adhesive with a dry cloth and clean with acetone, isopropyl alcohol, or citrus based solvents according to manufacturer’s instructions. Cured adhesive may be removed by scraping from surface.
See first aid treatment for skin contact.
Is Gorilla Clear Grip® gap filling?
No
Is Gorilla Clear Grip® UV Resistant?
Yes
Can Gorilla Clear Grip® be used both indoors and outdoors?
Yes, Gorilla Clear Grip® can be used both indoors and outdoors.
Is Gorilla Clear Grip® stainable?
Yes, Gorilla Clear Grip® is stainable when fully cured.
Is Gorilla Clear Grip® sandable?
Yes, cured Gorilla Clear Grip® is sandable.
Is Gorilla Clear Grip® paintable?
Yes, when fully cured.
Is Gorilla Clear Grip® Washer/Dryer safe?
Yes
Is Gorilla Clear Grip® photo safe?
Gorilla Clear Grip® is safe to use with photos.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Primer & Additive is a water-based multipurpose solution that improves the bond between porous substrates and adhesives, waterproofing membranes, or screeds. It can be used as a primer before tiling or as an additive to strengthen screeds and grouts.
Surface Preparation:
Ensure the surface is clean, dry, and free of dust, oil, wax, paint, or other contaminants. For new concrete or screeds, allow to cure completely. Fill cracks and voids using a patching compound.
Application Instructions:
As a primer, dilute 1 part Dunlop Primer & Additive with 3 parts water. Apply evenly using a brush or roller. Allow it to dry for at least 30 minutes before applying adhesives or membranes.
As an additive, replace part or all of the mixing water in tile adhesives or grouts to improve flexibility and adhesion. Follow the manufacturer's recommended ratios.
Coverage:
Approximately 6–10m² per litre, depending on surface porosity.
Drying Time:
Allow to dry for at least 30 minutes before overcoating. Drying may vary depending on temperature and humidity.
Clean Up:
Clean tools and equipment with water immediately after use.
Technical Data:
Base: Water-based acrylic polymer
pH: Neutral
Appearance: Milky white liquid
Shelf Life: 12 months (unopened in cool, dry conditions)
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Express Wet Area Waterproofing Membrane is a high-performance, fast-drying liquid membrane designed for use in internal wet areas including bathrooms, showers, laundries, and kitchens. This flexible, water-based acrylic polyurethane formulation creates a seamless and highly durable waterproof barrier that is tile-ready within hours.
It’s suitable for use under tile adhesives, screeds, and other flooring products. The product forms a tough, elastomeric layer that resists movement, cracking, and water penetration. It meets the requirements of Class III membranes and is suitable for both floor and wall applications.
Surface Preparation:
Ensure all surfaces are clean, dry, and structurally sound. Remove dust, grease, oil, curing compounds, and loose or flaking materials. Prime all surfaces using a compatible primer. On porous or highly absorbent surfaces, apply a second primer coat if needed. Any existing cracks, gaps, or joints should be sealed or reinforced using bond breakers or reinforcing fabric.
Application Instructions:
Apply the membrane using a brush or roller.
Two coats are required for effective waterproofing.
First coat should be applied in one direction.
Once dry to the touch (approx. 2 hours), apply the second coat in the opposite direction.
Membrane should extend at least 150mm up walls in general wet areas and 1.8m in shower recesses.
Waterproofing must be applied continuously and without breaks or pinholes.
Use reinforcing fabric over joints and corners if required.
Avoid application in conditions below 10°C or above 35°C.
Coverage:
Approximately 1m² per litre per coat. A 5kg pail covers roughly 2.5m² with two coats, depending on surface porosity.
Drying Time:
Touch dry: 1–2 hours
Recoat time: 2 hours
Ready for tiling: 4–6 hours
Fully cured: 24 hours
Drying times will vary with ambient temperature and humidity.
Clean Up:
Clean tools and equipment immediately after use with water. Do not allow membrane to dry on tools.
Technical Data:
Type: Water-based acrylic polyurethane
Classification: Class III membrane
Application Method: Brush or roller
Flexibility: High
Water Resistance: Excellent
Colour: Grey
Shelf Life: 12 months (unopened in cool, dry conditions)
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Damp-Proof Waterproofing is an acrylic brush-on membrane designed to prevent rising damp, efflorescence, and resist negative hydrostatic pressure. It adheres excellently to substrates including brick, masonry, concrete block, concrete, stone, and timber, and can be easily applied using a brush or roller. Once cured, it can be overcoated with most decorative paints.
Surface Preparation: Ensure all surfaces are structurally sound and free from existing coatings, adhesives, and efflorescence to achieve maximum bond strength and resistance to hydrostatic pressure. Surfaces may be damp but not wet and must be cleaned free of dirt, grease, oil, or other contaminants. Fill holes and non-structural cracks with a suitable floor repairer before application.
Application Instructions:
For Floors: Spread the material using a brush or long nap roller to achieve coverage, then finish with a long nap roller.
For Walls: Apply using a brush, roller, or spray, ensuring even coverage.
Work the material into voids to avoid pinholing.
For areas affected by hydrostatic pressure, apply a minimum of two coats. The second coat can be applied after 4 hours. Ensure uniform coverage and the required dry film thickness per coat.
Coverage:
Single Coat: Approximately 3m² per litre, per coat, when used as a barrier to efflorescence or as a moisture-resistant coating over green concrete.
Multiple Coats: For areas with hydrostatic pressure, two coats are required at a coverage rate of 1.5m² per litre per coat. Additional coats may be necessary to achieve uniform coverage.
Drying Time: Allow the membrane to cure for 24 hours before applying adhesives, mortars, decorative coatings, or other surface treatments. Ensure the membrane is not damaged during subsequent treatments. For floor surfaces, allow the final coating to cure for at least 24 hours before further treatment to minimize the risk of mechanical damage.
Clean Up: Wash all equipment with water or a water/detergent mixture immediately after use.
Technical Data:
Base: Acrylic
Application Temperature: 10°C to 35°C
Dry Film Thickness: Achieve required thickness as per application guidelines
Curing Time: 24 hours before overcoating
Shelf Life: Refer to packaging for details
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Davco SMP Evo Tile Adhesive is a high-performance, flexible cement-based adhesive ideal for the installation of natural stone, porcelain, and marble tiles. Specially designed with advanced low-dust technology, it provides a cleaner and safer working environment. Its superior non-slump properties make it perfect for wall and floor tiling, including large-format tiles.
Surface Preparation:
Ensure surfaces are structurally sound, dry, and free from contaminants like dust, oil, and wax. Smooth surfaces should be roughened slightly, and absorbent substrates should be primed. Existing tiles must be clean, dry, and securely bonded.
Mixing:
Mix 5kg of powder with approximately 1.4–1.5L of clean water using a mechanical mixer until a smooth, lump-free paste is formed. Allow it to stand for 5 minutes before remixing. Do not add more water after mixing.
Application:
Apply the adhesive with a notched trowel over an area no larger than can be tiled within the open time. Firmly press tiles into the adhesive bed with a twisting motion to ensure full contact. Back-buttering may be necessary for large tiles or uneven substrates.
Coverage:
Approximately 1.5–1.75m² per 5kg bag using a 10mm notch trowel.
Drying Time:
Tiles can generally be grouted after 24 hours. Allow 2 days before exposure to water in wet areas and 21 days for submerged areas like pools.
Clean-up:
Clean tools and excess adhesive with water before it sets. Once cured, adhesive must be removed mechanically.
Technical Data:
Classification: C2S1TE
Pot life: 1.5 hours
Open time: 30 minutes
Adjustability time: 20 minutes
VOC content: Low
Appearance: White powder
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Concentrated grout additive designed to increase the flexibility, strength and water resistance of cement based grouts.
Davco® 4 in 1 Grout Additive is suitable for interior and exterior domestic applications. Ideal for submerged and high foot traffic areas, where a high degree of deformability is required.
Increases flexibility, strength and water resistance of cement based grout
Enhances the colour of grout
Reduced likelihood of efflorescence
Usage
To reduce the porosity of cement based grouts
To improve the compressive strength of cement based grouts
To improve the flexural strength of cement-based grouts
Suitable for use when grouting over fibre cement sheet floors and swimming pools or where a greater performance level / heavy duty performance is required
Advantages
Increases flexibility, strength and water resistance of cement based grout
Enhances the colour of grout
Reduced likelihood of efflorescence
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Noise, vibration, and impact dampening properties are exceptional.
Adhesion and sealing qualities are excellent.
Tack-free time and cure speed are both quick.
It's safe to use in both salt and fresh water.
Designed in Australia
Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik.
Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications.
It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Noise, vibration, and impact dampening properties are exceptional.
Adhesion and sealing qualities are excellent.
Tack-free time and cure speed are both quick.
It's safe to use in both salt and fresh water.
Designed in Australia
Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik.
Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications.
It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bostik Seal it Kitchen & Bathroom White: The All-In-One Solution for Wet Areas
Product Overview
A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments.
Key Features
Neutral cure for versatile application
Excellent for UV exposure and porous surfaces
Resistant to mold and mildew
±25% joint movement capabilities
WaterMark approved for quality assurance
Low odour and UV resistant
Safe on various materials including galvanized steel and concrete
Where to Use
This product is ideal for sealing in:
Kitchens, bathrooms, toilets, and showers
Basins and vanity units
Glass partitions
Ceramic tiles
Vitreous enamel
Most laminated surfaces
Fibre glass
Rimless sinks
Instructions
Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bostik Seal it Kitchen & Bathroom Translucent: The All-In-One Solution for Wet Areas
Product Overview
A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments.
Key Features
Neutral cure for versatile application
Excellent for UV exposure and porous surfaces
Resistant to mold and mildew
±25% joint movement capabilities
WaterMark approved for quality assurance
Low odour and UV resistant
Safe on various materials including galvanized steel and concrete
Where to Use
This product is ideal for sealing in:
Kitchens, bathrooms, toilets, and showers
Basins and vanity units
Glass partitions
Ceramic tiles
Vitreous enamel
Most laminated surfaces
Fibre glass
Rimless sinks
Instructions
Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bostik Seal it Kitchen & Bathroom Light Grey: The All-In-One Solution for Wet Areas
Product Overview
A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments.
Key Features
Neutral cure for versatile application
Excellent for UV exposure and porous surfaces
Resistant to mold and mildew
±25% joint movement capabilities
WaterMark approved for quality assurance
Low odour and UV resistant
Safe on various materials including galvanized steel and concrete
Where to Use
This product is ideal for sealing in:
Kitchens, bathrooms, toilets, and showers
Basins and vanity units
Glass partitions
Ceramic tiles
Vitreous enamel
Most laminated surfaces
Fibre glass
Rimless sinks
Instructions
Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bostik Nail It Instant Grab White: Grab It Fast, Hold It Forever
Product Overview
Bostik Nail It Instant Grab White is a high-quality professional adhesive crafted with MSP (Modified-Silyl Polymer) technology. It offers extremely high initial tack, eliminating the need for fixation or support during curing.
Smart Advantages
Extremely high initial tack
No fixation or support needed during curing
Free of isocyanates, phthalates, solvents, and silicones
Suitable for both interior and exterior use
Non-corrosive towards metals
Almost odorless
Resistant to moisture, weather, and UV
Applications
Universal bonding adhesive suitable for:
Stone, Concrete, Glass
Metals, Alloys, Stainless steel
Plastics, Polyurethane, PVC
Wood, Paint Systems
Directions for Use
Application should be done in vertical stripes using a caulking gun. No need for fixation or support due to high initial strength.
Limitations
Not suitable for certain plastics, continuous water exposure, or movement joints.
Cleaning & Safety
Remove excess uncured adhesive with Bostik Handy Wipe or a damp cloth. Cured adhesive can only be mechanically removed.
Product Codes & Specifications
Available in 290ml cartridges. Temperature resistance ranges from -40°C to +90°C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Betta Tilecare Wet Area Waterproofer is a flexible, fast-drying, liquid rubber membrane designed for waterproofing internal wet areas such as bathrooms, showers, laundries, and tiled spaces. It provides a durable, seamless moisture barrier that resists water pressure and prevents leaks when applied beneath tiles, screeds, or surface coatings.
Surface Preparation:
All surfaces must be clean, dry, and structurally sound. Remove dust, oil, grease, wax, and loose or flaking material. Smooth, glossy surfaces should be roughened or etched. Rough or uneven surfaces should be patched and leveled. Mechanically remove any surface contamination or de-bonded coatings for optimal adhesion.
Priming (if required):
Use a compatible primer on highly porous, glossy, or damp surfaces to promote adhesion. Ensure primed surfaces are dry before applying the membrane.
Application Instructions:
Apply a bond breaker system such as joint tape or fabric to corners, joints, and penetrations.
Apply the first coat using a brush or roller, working it into the surface to avoid pinholes.
Allow the first coat to dry (approx. 1 hour), then apply the second coat in the opposite direction.
Total coverage should be at least 1.5L/m², forming a final dried film thickness of approximately 1.2mm.
Coverage should extend up walls at least 150mm in general areas and 1800mm in shower recesses.
Allow the membrane to cure fully before tiling or overcoating.
Coverage:
Approximately 1.5L per square metre for two coats, depending on surface porosity.
Drying Time:
Tack-free: 45 minutes
Recoat: 1 hour
Ready for tiling: 4 hours
Flood test ready: 16 hours
Dry times may vary based on temperature and humidity.
Clean Up:
Clean tools and equipment with water immediately after use.
Technical Data:
Base: Water-based liquid rubber
Colour: Grey
Finish: Flexible, seamless membrane
Dried Film Thickness: Approx. 1.2mm (after two coats)
Application Temp: 5°C to 35°C
Shelf Life: Refer to packaging for details
Sealants/adhesives engineered to accommodate movement without cracking. Check stated movement capability for your joint design. Use filters to refine by chemistry and cure speed. Always review the product page and TDS/SDS.
![Poly Gap Filler Sealant Multipurpose [White]](http://gluesaustralia.com.au/cdn/shop/files/9311531000683_aaee7eb0-0b5d-4d11-8699-1eea1db48c2c.png?v=1754712208&width=645)
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Light Grey]](http://gluesaustralia.com.au/cdn/shop/files/9311531002762_be7a4237-355f-47f3-ae09-dabb40913652.png?v=1754712211&width=645)
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Cedar]](http://gluesaustralia.com.au/cdn/shop/files/9311531002731_8a23516e-dc7a-4a74-9fda-5436c7c62091.jpg?v=1754712214&width=645)
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Black]](http://gluesaustralia.com.au/cdn/shop/files/9311531002724_6b56cb9d-718d-4289-8566-b1965f6372f4.webp?v=1754712217&width=645)
![Parfix Window Glass Silicone Sealant Interior Exterior [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115942_3d0cfbff-93da-42bb-89d0-8cab3402309a.jpg?v=1754712239&width=645)
![Parfix Roof Gutter Concrete Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115744_c50eb875-361a-40d9-9352-04fade1d8d60.jpg?v=1754712244&width=645)
![Parfix Roof Gutter Concrete Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697115768_c056520c-16e5-4bd6-9d65-de084d15ff93.jpg?v=1754712245&width=645)
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
![Parfix Kitchen & Bathroom Silicone Sealant 300g [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697115928_85e9adb4-ec92-46ea-8eda-b6ab353e59f8.jpg?v=1754712261&width=645)
![Parfix Gap Filler Flexible Paintable Interior [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697115812_e966678a-f2ee-4e79-abc6-2f960851c302.png?v=1754712264&width=645)
![Monarch Mini Silicone Mould Resistant [White]](http://gluesaustralia.com.au/cdn/shop/files/9320090029066_2af7d350-636b-476c-9c8a-71b4ddb4f0e5.png?v=1754712301&width=645)
![Monarch Mini Silicone Mould Resistant [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9320090029073_9b2a79dd-e58b-4fb6-a3b1-d6525871d967.png?v=1754712303&width=645)
![Monarch Mini Roof and Gutter Silicone [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090029257_ad8c4dd8-7138-4341-881e-1e58084dc0c8.png?v=1754716023&width=645)
![Monarch Mini Roof and Gutter Silicone [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090029257_d1f88907-d8a6-4e7f-b887-a4ac4f2ab20a.png?v=1754716023&width=645)
![Monarch Mini Gap Filler [White]](http://gluesaustralia.com.au/cdn/shop/files/9320090029080_1b178ddb-e3de-4ec1-83bb-8e320595bdb3.jpg?v=1754712311&width=645)
![Monarch Mini Gap Filler [Cream]](http://gluesaustralia.com.au/cdn/shop/files/9320090030581_c5a95353-e7ee-4d92-8445-93066291f976.jpg?v=1754712313&width=645)
![Monarch Mini Gap Filler [Brown]](http://gluesaustralia.com.au/cdn/shop/files/9320090030574_91b63521-91d4-427c-ba6f-c5f54343a9c6.jpg?v=1754712314&width=645)
![Monarch Mini Gap Filler [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090030567_dd3b7bac-a9e5-4986-9275-2bff35fb52de.jpg?v=1754712316&width=645)
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/9310492265001_6fb5fccc-7784-41bb-9997-bbd917e3c834.png?v=1754712704&width=645)
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9310492265025_0316718a-8147-4bdd-955a-19d6d8a0bc59.png?v=1754712705&width=645)
![Poly Gap Filler Sealant Multipurpose [White]](//gluesaustralia.com.au/cdn/shop/files/9311531000683_aaee7eb0-0b5d-4d11-8699-1eea1db48c2c.png?v=1754712208&width=645)
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Light Grey]](//gluesaustralia.com.au/cdn/shop/files/9311531002762_be7a4237-355f-47f3-ae09-dabb40913652.png?v=1754712211&width=645)
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Cedar]](//gluesaustralia.com.au/cdn/shop/files/9311531002731_8a23516e-dc7a-4a74-9fda-5436c7c62091.jpg?v=1754712214&width=645)
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Black]](//gluesaustralia.com.au/cdn/shop/files/9311531002724_6b56cb9d-718d-4289-8566-b1965f6372f4.webp?v=1754712217&width=645)
![Parfix Window Glass Silicone Sealant Interior Exterior [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697115942_3d0cfbff-93da-42bb-89d0-8cab3402309a.jpg?v=1754712239&width=645)
![Parfix Roof Gutter Concrete Silicone Sealant [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697115744_c50eb875-361a-40d9-9352-04fade1d8d60.jpg?v=1754712244&width=645)
![Parfix Roof Gutter Concrete Silicone Sealant [Black]](//gluesaustralia.com.au/cdn/shop/files/9300697115768_c056520c-16e5-4bd6-9d65-de084d15ff93.jpg?v=1754712245&width=645)
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
![Parfix Kitchen & Bathroom Silicone Sealant 300g [White]](//gluesaustralia.com.au/cdn/shop/files/9300697115928_85e9adb4-ec92-46ea-8eda-b6ab353e59f8.jpg?v=1754712261&width=645)
![Parfix Gap Filler Flexible Paintable Interior [White]](//gluesaustralia.com.au/cdn/shop/files/9300697115812_e966678a-f2ee-4e79-abc6-2f960851c302.png?v=1754712264&width=645)
![Monarch Mini Silicone Mould Resistant [White]](//gluesaustralia.com.au/cdn/shop/files/9320090029066_2af7d350-636b-476c-9c8a-71b4ddb4f0e5.png?v=1754712301&width=645)
![Monarch Mini Silicone Mould Resistant [Translucent]](//gluesaustralia.com.au/cdn/shop/files/9320090029073_9b2a79dd-e58b-4fb6-a3b1-d6525871d967.png?v=1754712303&width=645)
![Monarch Mini Roof and Gutter Silicone [Black]](//gluesaustralia.com.au/cdn/shop/files/9320090029257_ad8c4dd8-7138-4341-881e-1e58084dc0c8.png?v=1754716023&width=645)
![Monarch Mini Roof and Gutter Silicone [Black]](//gluesaustralia.com.au/cdn/shop/files/9320090029257_d1f88907-d8a6-4e7f-b887-a4ac4f2ab20a.png?v=1754716023&width=645)
![Monarch Mini Gap Filler [White]](//gluesaustralia.com.au/cdn/shop/files/9320090029080_1b178ddb-e3de-4ec1-83bb-8e320595bdb3.jpg?v=1754712311&width=645)
![Monarch Mini Gap Filler [Cream]](//gluesaustralia.com.au/cdn/shop/files/9320090030581_c5a95353-e7ee-4d92-8445-93066291f976.jpg?v=1754712313&width=645)
![Monarch Mini Gap Filler [Brown]](//gluesaustralia.com.au/cdn/shop/files/9320090030574_91b63521-91d4-427c-ba6f-c5f54343a9c6.jpg?v=1754712314&width=645)
![Monarch Mini Gap Filler [Black]](//gluesaustralia.com.au/cdn/shop/files/9320090030567_dd3b7bac-a9e5-4986-9275-2bff35fb52de.jpg?v=1754712316&width=645)
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]](//gluesaustralia.com.au/cdn/shop/files/9310492265001_6fb5fccc-7784-41bb-9997-bbd917e3c834.png?v=1754712704&width=645)
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [Black]](//gluesaustralia.com.au/cdn/shop/files/9310492265025_0316718a-8147-4bdd-955a-19d6d8a0bc59.png?v=1754712705&width=645)
