Fuel & Oil Resistant

Sikaflex-227 is a one-component poly­­urethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.

Read more less

Loxeal 58-11 Anaerobic Thread Sealant Loxeal 58-11 is a high performance anaerobic sealant designed for metal thread joints only. It replaces PTFE tape and cord, delivers instant sealing against moderate pressure, and cures to form a shock and vibration resistant seal that remains reliable from -55°C to +150°C. Why choose Loxeal 58-11 Instant sealing against moderate pressure to get systems back in service fast. Thixotropic formulation stays where you put it and resists migration on threads. Wide chemical compatibility including gas, water, LPG, hydrocarbons, oils and more. Shock and vibration resistant for durable, leak free joints. Temperature range from -55°C to +150°C for tough Australian conditions. Certified and approved Gas approvals: DVGW and DIN EN 751-1, plus Australian Gas Association for working pressure up to 20 bar. Oxygen service: Approved for gaseous oxygen up to 10 bar at +60°C. Potable water: WRAS listed and suitable for contact with wholesome water. Also approved for contact with drinking water by Global Mark. Food area use: NSF registered category S4 for use as an adhesive in and around food processing areas. Hydrogen: Tested by KIWA as a sealant for use with pure hydrogen to EN 751-1. Typical applications Sealing tapered and parallel metal threaded fittings in plumbing, HVAC, gas and hydraulic systems. Replacing PTFE tape or thread cord on metal pipework where a permanent, pressure resistant seal is needed. Directions Clean and degrease threads thoroughly. Cut the nozzle to the required bead size. Apply a continuous bead 1 to 2 threads back from the leading edge. Ensure full coverage around the circumference. Assemble and tighten the joint. Wipe away excess uncured material. Allow to cure (see Cure times). Cure speed can be accelerated on passive metals or at low temperature with an appropriate activator. Cure times at +25°C Handling: 15 to 30 minutes Functional: 1 to 3 hours Time to water service for potable water systems at +21.1°C Brass, copper, cast iron: 24 hours Stainless steel, aluminium: 7 days Technical data Chemistry Anaerobic methacrylate Colour Yellow (fluorescent under blue light) Viscosity at +25°C 20,000 to 80,000 mPa·s, thixotropic Specific gravity Approx. 1.1 g/ml Gap filling Up to 0.30 mm (M56 / 2 inch) Flash point Greater than +100°C Shear strength 6 to 13 N/mm² (ISO 10123) Breakaway torque 18 to 24 N·m (ISO 10964) Prevailing torque 7 to 14 N·m (ISO 10964) Service temperature -55°C to +150°C Shelf life 1 year in unopened packaging at ? +25°C Chemical resistance Excellent resistance to motor oil, gearbox oil, gasoline and hydraulic oil. Excellent to good resistance in 50 percent water glycol at elevated temperature. Limitations and notes For metal to metal threaded joints only. Not suitable for plastic threads or rubber components. Liquid product can attack some coatings and plastics. Pre test if unsure. For disassembly, use normal tools. Heat components to approximately +150°C to +250°C if required, then remove cured residue mechanically and clean with solvent. Store in a cool, dry place at or below +25°C. Do not return unused product to the bottle. All technical information is provided as a guide only. Always verify suitability with your specific materials, operating pressures and local regulations before use. Follow all safety and handling instructions on the product label and safety data sheet.

Read more less

Selleys Auto Fix Auto Sealant Translucent 100 mL Keep water out and vibrations at bay with a clear automotive sealant that bonds fast and stays flexible. Selleys Auto Fix Auto Sealant is a 100 percent neutral cure silicone designed for cars, caravans, and general automotive sealing where a durable waterproof finish is essential. Why you will like it 100 percent neutral cure silicone Versatile general purpose sealant for automotive use Waterproof seal that resists vibration and temperature extremes UV and weather resistant for long lasting performance Skins in 5 minutes, set to touch in 30 minutes, full cure in 24 hours Where to use it Adheres to most auto and caravan materials, including: Glass and painted surfaces Fiberglass and most plastics Trim components Most rubbers Typical applications Sealing around lights, windows, and trim Gasket style sealing where a flexible waterproof joint is required General leak prevention and small gap sealing in automotive and caravan fittings Directions Preparation: Clean surfaces so they are free of dust, oil, and moisture. Wipe with mineral turpentine and allow to dry. Cut and load: Remove cap, unscrew nozzle, remove seal. Refit nozzle and cut at a 45 degree angle to the desired bead size. Apply: Squeeze the tube with steady pressure to lay a continuous bead. Smooth with a gloved finger before the sealant skins. Clean up: Before cure, clean tools and excess with mineral turpentine. Once cured, remove by cutting or scraping. After use: Replace cap. Let cured material in the nozzle be removed before next use. Handy tips Mask edges for neat joints. Remove tape before skin forms. Work within the skin time to achieve a smooth finish. Limitations Not recommended for Natural rubber, NBR, or Chloroprene Neoprene Technical details Technology 100 percent neutral cure silicone Colour Translucent Packaging Tube 100 mL Density 1.02 g per mL Application temperature -20°C to 50°C Skin time 5 minutes Shore A hardness 25 Elongation at break 370 percent Movement capability 25 percent Service temperature -40°C to 180°C VOC 26 g per L Clean up and storage Clean uncured sealant with mineral turpentine Store below 30°C in a cool dry place Use within 24 months from date of production Safety: Refer to the product SDS for handling and first aid information. Use in a well ventilated area and keep out of reach of children.

Read more less

Selleys Auto Fix Windscreen Sealant 100 mL - Black Stop leaks fast around windscreens and windows with a durable, weather resistant silicone seal. Selleys Auto Fix Windscreen Sealant forms a waterproof barrier that resists vibration, UV and temperature extremes, keeping water, dust and drafts out. Why choose this sealant 100 percent neutral cure silicone for reliable sealing Forms a waterproof seal to stop leaks quickly UV and weather resistant for long term performance Skins in 5 minutes and is touch dry in about 30 minutes Handles joint movement up to 25 percent Suitable surfaces Glass and windscreens Rubber surrounds and trims Painted surfaces and most plastics Metal frames and channels Typical applications Sealing between windscreen glass and rubber Sealing between rubber and metal frames Stopping minor water ingress around vehicle windows General sealing where a flexible, black silicone finish is desired Key specifications Technology Neutral cure silicone Colour Black Movement capability Up to 25 percent Skin time About 5 minutes Set time About 30 minutes Full cure Approximately 24 hours Service temperature -40°C to 180°C Application temperature -20°C to 50°C VOC 26 g/L Pack size 100 mL tube Directions Remove any dirt or moisture between the rubber and glass, or rubber and metal. Clean with mineral turpentine and allow to dry. Remove cap, unscrew nozzle, pierce inner seal, refit nozzle, then cut the tip at a 45 degree angle. Insert the nozzle between the rubber and glass or rubber and metal where possible. Squeeze the tube with steady pressure to push sealant into the joint. Smooth off with a gloved finger. If additional smoothing is needed, do it before the sealant skins. Clean up uncured sealant with mineral turpentine. Cured material must be cut or scraped away. Replace the cap after use. Allow sealant in the nozzle to cure, then remove before next use. Handy tips For neat lines, mask both sides of the joint and remove tape before the sealant skins. Best results occur when the joint is clean, dry and free of loose material. Limitations Not recommended on natural rubber, NBR or chloroprene neoprene due to poor adhesion. Clean up and storage Clean uncured sealant with mineral turpentine. Remove cured sealant by cutting or scraping. Store in a cool, dry place below 30°C. Use within 24 months of production. What you get 1 x Selleys Auto Fix Windscreen Sealant 100 mL - Black

Read more less

Boston Liquid Thread Sealant 50g Boston Liquid Thread Sealant is an anaerobic sealant formulated to seal metal threads on gas and water pipes. It cures in the absence of air once confined between metal surfaces, creating a reliable, leak resistant seal. Why choose this sealant Seals metal threaded fittings for gas and water systems Fast handling strength in 10 to 20 minutes at room temperature Full cure in 24 hours for long lasting performance Resists vibration and helps prevent loosening Approved for gas service and type tested for contact with potable water Where to use Metal to metal threaded connections on gas lines and appliances Metal to metal threaded connections on cold and warm water pipes up to 55°C Not suitable for Plastic, glass, or rubber parts Non threaded gaps or joints exposed to air Continuous steam temperatures above 135°C Directions Remove oil and contamination from threads. Ensure parts are clean and dry. Apply sealant to one surface, covering 2 to 3 thread rotations. Assemble threads. Wipe off any excess sealant immediately. Allow 10 to 20 minutes for initial cure before pressurising. Allow 24 hours for full cure. Disassembly can be performed using standard hand tools. Good to know Anaerobic sealants cure when air is excluded between metal parts. Sealant exposed to air will not cure. Packaging is larger than contents to prevent in bottle curing. Net content is 50g. Always wipe away excess to avoid any metallic taste from uncured material in potable water systems. Apply with good ventilation. If contact occurs with eyes or skin, flush with clean water immediately. Store in a cool, dry place. Keep out of reach of children. Approvals and compliance Approved by the Australian Gas Association (Cert. No. 7583, Class III, 2000 kPa) Type Tested AS/NZS 4020 (PTT40067, SAI Global) Specifications Chemistry Anaerobic thread sealant for metal parts Pack size 50g Initial cure 10 to 20 minutes Full cure 24 hours Gas temperature range -10°C to +135°C Water temperature range Up to 55°C Pressure class Class III, up to 2000 kPa Substrates Metal to metal threads only What is included 1 x Boston Liquid Thread Sealant 50g tube.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

Sikaflex-227 is a one-component poly­­urethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.

Read more less

Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 5–35°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.

Read more less

Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 5–35°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.

Read more less

Silicone 401 RTV is a one part ready to use, acid cure, room temperature vulcanising (RTV), silicone adhesive sealant. It cures rapidly on exposure to atmospheric moisture to form a versatile, durable, resilient silicone rubber. It is available in clear. Uses Silicone 401 is suitable for form-in-place gaskets and for adhesive, sealing and electrical insulating applications in manufacturing and plant maintenance. Technical Features Wide Temperature Tolerance: Remains permanently flexible under operating temperatures from – 60oC to 205oC, and will tolerate short periods of 260oC Good Chemical Resistance: Good resistance to most organic and inorganic chemicals, solvents and oils Primerless Adhesion: Adheres without primer to many metal, glass, ceramic, rigid plastic, rubber painted and wood substrates Non-toxic: Suitable for incidental food contact in food handling equipment and food contact surfaces Excellent Weatherability: Excellent resistance to ozone, UV light and ageing Good Electrical Insulating Properties: Insulating properties are comparable to other insulating rubbers at room temperature, though performs better than many other rubbers at higher temperatures and water has little effect on these properties Application Tips Not recommended for use with petrol, distillate and some other hydrocarbon solvents. These can cause softening and swelling which is undesirable in some applications. Do not use in totally confined joints where sealant is not exposed to atmospheric moisture Chemical compatibility should be tested for each application under consideration Cannot be over-painted Technical Details and Performance Indicative information only, not to be used for setting specifications. Typical Application Properties Consistency Non – sag, gun grade Tack Free Time (25oC, 50% r.h.): 15 – 20 minutes Skin Forming Time 5 to 10 minutes (depending on weather conditions) Cure Time (3mm Section @ 25oC, 50% R.H.): 24 hours Shrinkage During Curing Approximately 3.5% by volume Specific Gravity 1.04 Storage Life (Below 30oC in original unopened container):12 months Typical Mechanical Performance Properties (3 day cure @ 25oC, 50% R.H.) Tensile Strength (MPa) 1.2 Ultimate Elongation % 400 Hardness (Shore A) 25 Tear Strength (N/mm) 5.0 Joint Movement Capability ± 25% Typical Electrical Properties (at Room Temperature) Dielectric Strength kv/mm 21 Dielectric Constant @50Hz to 5MHz 2.6-2.8 Dissipation Factor Tan @50Hz-5MHz 20×10-4 to 5×10-4 Volume Resistivity (ohm-cm) 1×1013 (wet 60oC) 1×1014 (dry 23oC) Typical Thermal Properties Brittle Point –60oC Maximum Continuous Operating Temperatures 205oC Maximum Intermittent Operating Temperatures 260oC

Read more less

PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.

Read more less

Retaining Compound - medium strength. If disassembly is required. Ideal for parts that need subsequent dismantling.   LOCTITE® 641 is designed for the bonding of cylindrical fitting parts, particularly where disassembly is required for servicing operations. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings.   Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings   Technical Information Colour Yellow Diametrical Clearance (Maximum) 0.1 mm Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.1 mm Shear Strength Unit, Steel psi Shear Strength, Steel 1700 Specific Gravity 1.07 g/l Specific Gravity Temperature 25 °C Substrates Metal: Steel Temperature -65 - 300 °F Viscosity 525 - 1950 mPa.s (cP) Brookfield Viscosity Temperature 77 °F

Read more less

LOCTITE 263 is designed for the permanent locking and sealing of threaded fasteners. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. It's particularly suited for heavy duty applications such as studs into motor housings, nuts onto studs in pump housings and other fasteners where high strength is required. LOCTITE 263 provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids. Recommended on High strength Locks studs against vibration loosening Controlled/torque tension Prevents thread corrosion Fast curing How to use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole.  For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours.  Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush.  For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 4. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 5. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 6. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 7. Assemble and tighten as required For Disassembly 1. Apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush

Read more less

Threadlocking Adhesive - medium strength. General purpose. Suitable for all metal threaded assemblies. LOCTITE® 243 is a general purpose threadlocker of medium bond strength. This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration. The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces. It is proven to be tolerant of minor contamination due to industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids. Prevents loosening on vibrating assemblies, e.g. pumps, gearboxes or presses. Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces). Proven to tolerate minor contamination by industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids Permits disassembly with hand tools for servicing Technology: Acrylic Chemical Type: Dimethacrylate ester Appearance (uncured) Blue liquidLMS Fluorescence Positive under UV lightLMS Components One component - requires no mixing Viscosity Medium, thixotropic Cure Anaerobic Secondary Cure Activator Application Threadlocking Strength Medium LOCTITE®  243™ is designed for the locking and sealing of threaded fasteners which require normal disassembly with standard hand toolsThe product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature of LOCTITE®  243™ reduces the migration of liquid product after application to the substrateLOCTITE® 243™ provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Safety Data Sheet (SDS). Where aqueous washing systems are used to clean the surfaces before bonding, it is important to check for compatibility of the washing solution with the adhesive. In some cases, these aqueous washes can affect the cure and performance of the adhesive. This product is not normally recommended for use on plastics (particularly thermoplastic materials where stress cracking of the plastic could result). Users are recommended to confirm the compatibility of the product with such substrates. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. Shake the product thoroughly before use 4. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 5. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 6. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 7. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 8. Assemble and tighten as required For Disassembly 1. Remove with standard hand tools 2. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot 3. Apply localized heat to the assembly to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush

Read more less

Loctite 222 Threadlocker prevents corrosion, loosening from shock or vibration, and seals to prevent leakage. It also allows for simple, hand tool disassembly without shearing the screw. Easy to remove, it is typically used with small screws up to 1/4 inch. Recommended on Low strength Stops vibration loosening of screws and seals against leakage Prevents thread corrosion Dismantle with normal hand tools How to Use: Step 1: Safety Precautions Keep out of reach of children.   Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole.  For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours.  Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush.  For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot.

Read more less

Hold It Australia T90 PENETRATOR Wicking Grade for Close Fitting Parts - 50ml Description: HOLDIT AUSTRALIA T90 Penetrant is a fast-curing, low viscosity anaerobic compound that seeks voids in assembled components to cure anaerobically on close-fitting metal parts. It's ideal for securing tightly fitted assemblies. Applications T90 is excellent for post-assembly application, effectively preventing loosening of metal threaded fasteners. It is suitable for securing parts with minimal clearance and repairing hairline cracks in metal castings. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. For porosity or hairline cracks in casting products, brush directly onto the parts. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces

Read more less

Hold It Australia T77 STUDLOCK High Strength for Bolts 25mm and Above - 50ml Description: HOLDIT AUSTRALIA T77 Studlock large diameter high strength threadlocker is a red, general purpose adhesive for permanent threaded assemblies. It effectively locks fasteners 1” and larger in diameter, providing a seal against leakage and corrosion while resisting attacks from lubricants and industrial liquids and gases. Applications Ideal for eliminating double nutting/welding in critical assemblies. T77 allows for reduced casting thickness and prevents cracked castings from interference fit stresses. Suitable for larger diameter studs with coarse threads and can be used to reclaim worn stud holes. Primers are recommended for large gaps and poorly fitting parts. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces

Read more less

Hold It Australia T22 SCREWLOCK Low Strength for Easy Disassembly - 50ml Description: HOLDIT AUSTRALIA T22 Screwlock is a low strength, anaerobic thread locking compound, ideal for locking threaded fasteners that require disassembly with standard hand tools. It performs excellently on aluminium, steel, plated, stainless steel, and special alloy parts. T22 is characterized by its good temperature and solvent resistance. Applications T22 is specifically formulated to lock and seal small screws (less than ¼”), including set screws with long engagement lengths. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry for optimal results. If the metal is inactive or the cure speed is too slow, apply HOLDIT AUSTRALIA AA471 Activator or HOLDIT AUSTRALIA AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow to fully cure before applying load. Properties of Uncured Material Chemical Type: Anaerobic Colour: Purple Toxicity: Low Solid Content: 100% Viscosity @ 25°C, cPs: 900-1,500 cps Specific Gravity: 1.05 Shelf Life: 24 months Performance of Cured Material Fixture Speed: 15-20 Min @ 22°C Full Cure: 24 Hours @ 22°C Temperature Range: -50°C to 150°C Product Conformity: MIL-S-46163A, ASTM D-5363, NSF Technical Datasheet The cure speed of HOLDIT AUSTRALIA T22 is dependent on temperature and substrate. The product shows a breakaway strength of 1Nm – 9Nm on 3/8” plain steel nut & bolt after 1 hour and 5Nm – 11Nm after 24 hours. On a 3/8” zinc nut & bolt, the strength is 1Nm – 4Nm after 24 hours. Environmental and Fluid Resistance Heat Age: 100% retention in Engine oil @ 150°C Brake Fluid @ 150°C: 85% retention ATF @ 150°C: 85% retention 50/50 water/ethylene glycol @ 120°C: 80% retention Water @ 100°C: 80% retention Gasoline @ 25°C: 95% retention Diesel Fuel @ 25°C: 100% retention Ethyl Alcohol @ 25°C: 90% retention Active & Inactive Metal Table Category Cure Speed Metals Super Active Very Fast Cure Brass, Copper, Magnesium Active Fast Cure Iron, Steel, Nickel, Aluminium Inactive Slow Cure Stainless Steel, Titanium, Zinc Passive Primer Necessary Anodized Aluminium, Galvanised Steel, Ceramics, Glass, Plastics, Painted Finishes

Read more less