Replacement adhesive strips to reuse your existing Command hooks and hangers. Fresh adhesive for reliable hold Easy to apply and remove cleanly Sized to fit matching hooks Examples of use: Refresh worn strips on bathroom hooks Swap seasonal decor without new hardware Rehang key rails and caddies
$5.29
Round adhesive clips to guide and tame charging or appliance cords. Keeps cables in place Damage-free removal Blends with modern setups Examples of use: Route a phone charger behind a nightstand Secure a lamp cord to a skirting board Organise USB leads near a workstation
$7.13
Bathroom caddy accessory that mounts without drilling for tidy storage. Water-resistant adhesive Rust-free design Removes cleanly from tiles and glass Examples of use: Hold soap and sponges at the sink Keep shower gels within reach Organise shaving accessories
$32.67
Stylish metal-finish adhesive hooks for a premium look without drilling. Modern finish elevates decor Strong hold on smooth surfaces Removes cleanly when needed Examples of use: Hang hats and bags in entryways Hold bath towels in style Organise accessories in wardrobes
$9.05
Replacement adhesive strips to reuse your existing Command hooks and hangers. Fresh adhesive for reliable hold Easy to apply and remove cleanly Sized to fit matching hooks Examples of use: Refresh worn strips on bathroom hooks Swap seasonal decor without new hardware Rehang key rails and caddies
$10.40
Clear mini hooks sized for kitchen tools and lightweight accessories. Food-area friendly surfaces Removes cleanly Compact, clear design Examples of use: Hang measuring spoons by the stove Hold tea towels or oven mitts Store small gadgets on a splashback
$6.95
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$7.65
Stylish metal-finish adhesive hooks for a premium look without drilling. Modern finish elevates decor Strong hold on smooth surfaces Removes cleanly when needed Examples of use: Hang hats and bags in entryways Hold bath towels in style Organise accessories in wardrobes
$10.29
Stylish metal-finish adhesive hooks for a premium look without drilling. Modern finish elevates decor Strong hold on smooth surfaces Removes cleanly when needed Examples of use: Hang hats and bags in entryways Hold bath towels in style Organise accessories in wardrobes
$9.62
Stylish metal-finish adhesive hooks for a premium look without drilling. Modern finish elevates decor Strong hold on smooth surfaces Removes cleanly when needed Examples of use: Hang hats and bags in entryways Hold bath towels in style Organise accessories in wardrobes
$17.05
Stylish metal-finish adhesive hooks for a premium look without drilling. Modern finish elevates decor Strong hold on smooth surfaces Removes cleanly when needed Examples of use: Hang hats and bags in entryways Hold bath towels in style Organise accessories in wardrobes
$39.27
High-capacity adhesive hook or strip for heavier household items. Big hold with clean removal For smooth, sealed surfaces No nails or screws required Examples of use: Hang large frames within rating Hold bulky robes or bags Mount organisers or small shelves
$5.24
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$9.82
Picture hanger engineered for wire-back or sawtooth frames with stable support. Quick stick-on install Clean removal with no wall damage Keeps frames level Examples of use: Hang framed art and certificates Display mirrors within weight rating Mount signage in halls
$8.02
Tiny hooks for lightweight items where discretion matters. Clear or white low-profile design Peel off without residue Ideal for renters and offices Examples of use: Hang fairy lights droppers Display small decor tags Hold charging cables or earphones
$5.24
Stylish metal-finish adhesive hooks for a premium look without drilling. Modern finish elevates decor Strong hold on smooth surfaces Removes cleanly when needed Examples of use: Hang hats and bags in entryways Hold bath towels in style Organise accessories in wardrobes
$9.98
Wall-mounted hanger to air, dry or stage outfits without drilling. Folds when not in use Strong adhesive backing Great for laundries and wardrobes Examples of use: Hang shirts after ironing Air-dry gym gear Stage school uniforms overnight
$7.73
Bathroom caddy accessory that mounts without drilling for tidy storage. Water-resistant adhesive Rust-free design Removes cleanly from tiles and glass Examples of use: Hold soap and sponges at the sink Keep shower gels within reach Organise shaving accessories
$15.82
High-capacity adhesive hook or strip for heavier household items. Big hold with clean removal For smooth, sealed surfaces No nails or screws required Examples of use: Hang large frames within rating Hold bulky robes or bags Mount organisers or small shelves
$9.24
Stylish metal-finish adhesive hooks for a premium look without drilling. Modern finish elevates decor Strong hold on smooth surfaces Removes cleanly when needed Examples of use: Hang hats and bags in entryways Hold bath towels in style Organise accessories in wardrobes
$18.88
High-capacity adhesive hook or strip for heavier household items. Big hold with clean removal For smooth, sealed surfaces No nails or screws required Examples of use: Hang large frames within rating Hold bulky robes or bags Mount organisers or small shelves
$16.95
Bathroom caddy accessory that mounts without drilling for tidy storage. Water-resistant adhesive Rust-free design Removes cleanly from tiles and glass Examples of use: Hold soap and sponges at the sink Keep shower gels within reach Organise shaving accessories
$41.95
Specialised hanger for canvas frames with stable, centred support. Designed for canvas bars Level hold without nails Removes cleanly Examples of use: Hang stretched canvas art Display craft canvases Rotate gallery pieces without patching holes
$6.71
Specialised hanger for canvas frames with stable, centred support. Designed for canvas bars Level hold without nails Removes cleanly Examples of use: Hang stretched canvas art Display craft canvases Rotate gallery pieces without patching holes
$7.98
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$19.66
Clear clips for routing lights and small cables with near-invisible finish. Low-profile and clear Adhesive removes cleanly Includes extra strips for repositioning Examples of use: Outline a window with fairy lights Hold LED string lights along a pergola Tidy USB cables on a desk edge
$15.23
Tiny hooks for lightweight items where discretion matters. Clear or white low-profile design Peel off without residue Ideal for renters and offices Examples of use: Hang fairy lights droppers Display small decor tags Hold charging cables or earphones
$6.23
Tiny hooks for lightweight items where discretion matters. Clear or white low-profile design Peel off without residue Ideal for renters and offices Examples of use: Hang fairy lights droppers Display small decor tags Hold charging cables or earphones
$14.68
High-capacity adhesive hook or strip for heavier household items. Big hold with clean removal For smooth, sealed surfaces No nails or screws required Examples of use: Hang large frames within rating Hold bulky robes or bags Mount organisers or small shelves
$10.08
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$12.92
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$12.62
Picture hanger engineered for wire-back or sawtooth frames with stable support. Quick stick-on install Clean removal with no wall damage Keeps frames level Examples of use: Hang framed art and certificates Display mirrors within weight rating Mount signage in halls
$12.06
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$12.40
Thin adhesive strips for posters and prints without pinholes or tape marks. Removes cleanly from painted walls Holds securely yet peels away Low profile for flat finish Examples of use: Mount kids’ posters in bedrooms Display timetables in a study Put up event signs for parties
$5.19
Clear clips for routing lights and small cables with near-invisible finish. Low-profile and clear Adhesive removes cleanly Includes extra strips for repositioning Examples of use: Outline a window with fairy lights Hold LED string lights along a pergola Tidy USB cables on a desk edge
$6.92
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$16.79
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$14.12
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$5.24
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$12.22
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$7.84
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$7.33
Damage-free picture hanging strips for clean, strong holds on flat surfaces. No nails, no residue on removal Holds frames level Suitable for painted walls and most smooth surfaces Examples of use: Mount family photos or art frames Hang lightweight notice boards Create gallery walls without drilling
$16.50
UNi-PRO Cornice Adhesive 2.5 kg Overview UNi-PRO Cornice Adhesive 2.5 kg is a high quality cornice adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials plaster cornice plasterboard masonry Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Apply between 10°C and 30°C in dry, draft free conditions. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Sets firm to hold cornice in place, full cure over 24 hours or as directed. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Wipe away fresh adhesive with a damp cloth. Scrape away set material carefully. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$19.75
Gyprock CSR Acrylic Stud Adhesive 1 kg is a reliable acrylic stud adhesive for secure plasterboard fixing chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 1 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Gyprock CSR CSR for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Gyprock CSR Acrylic Stud Adhesive 1 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Fixing plasterboard to studs and battens Reducing the chance of nail pops and drumminess Suitable surfaces The adhesive works well on the following surface types when properly prepared: Timber framing and battens Metal studs as directed by code Back of plasterboard Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of install sheets within the wet time window. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Apply daubs as specified, then fix sheets with screws or nails. Adhesive cures to a resilient bond that complements mechanical fastening. Temperature and environmental performance Use in moderate temperatures for consistent cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean fresh residue with a damp cloth. Scrape away cured beads before setting coats. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed. Do not allow to skin in the tub. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$23.57
Bastion High-Bond Stud Adhesive 5.2 kg is a reliable stud adhesive for fixing plasterboard to timber or metal framing chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 5.2 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Bastion High-Bond for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Bastion High-Bond Stud Adhesive 5.2 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Plasterboard installation on studs Reducing screw count by bonding and fixing together Renovations where clean bond lines are important Suitable surfaces The adhesive works well on the following surface types when properly prepared: Timber studs Galvanised metal studs Plasterboard back surfaces Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of work within the wet time window to ensure transfer. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Applies as a bead to studs. Press board into place and fix with screws while the adhesive is wet. Final cure occurs as the solvent or moisture leaves the bead. Temperature and environmental performance Use in dry, shaded conditions during lining work. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Remove fresh smears with a suitable cleaner. Trim cured squeeze out before finishing. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store closed and away from heat sources. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$29.39
![Bostik Blu Stik Glue Sticks 35g [10 Pack]](http://gluesaustralia.com.au/cdn/shop/files/3247a52b-3527-4297-825a-a050176be4e8_d6fe2015-9cbc-4930-b3d1-683224070b7d.png?v=1760577211&width=645)
Key features Goes on blue, dries clear for easy, mess free gluing Non toxic, acid free and solvent free Fast drying with a strong hold on porous materials Allows brief repositioning before it sets Twist up stick with tight sealing cap to prevent drying out Low mess and easy to use for kids and adults Great value multi pack for classrooms and home offices Ideal for Paper and cardboard Photos and craft paper Lightweight fabric embellishments School assignments, posters and scrapbooks Directions Surfaces should be clean, dry and free of dust. Uncap and twist the base to raise the glue. Apply a thin, even layer to one surface. Join parts and press firmly for several seconds. Allow to dry. Full strength is reached after the glue has set clear. Clean up and safety Wipe fresh residue with a damp cloth. Wash hands and tools with warm soapy water. Keep capped when not in use. Keep out of reach of young children. Good to know Not recommended for non porous surfaces like metal or glass. For best results, store in a cool, dry place. Pack contents 10 glue sticks x 35 g each.
$33.50
Bostik Green Stik is an easy to use glue stick for everyday crafting, school projects, and office tasks. It applies smoothly, goes on clear, and dries clear for a neat finish. Why you will love it Non toxic and acid free Smooth application with strong initial tack Ideal for paper crafting, cut and paste, and classroom use Low mess and easy to control for kids and adults Surfaces Paper Cardboard Light fabric and similar porous materials How to use Ensure surfaces are clean, dry, and free from dust. Twist the base to raise the glue. Apply a thin, even layer to one surface. Press surfaces together firmly for several seconds. Allow to dry. For best results on heavier paper, apply to both surfaces. Clean up Wipe away excess with a damp cloth while still wet. Allow to dry fully before handling. Environment and packaging Formulated with a high percentage of natural ingredients Packaged in a recycled plastic container with soy ink label Packaging is curbside recyclable in many areas when the lid is attached Good to know Colour when applied: clear Dries: clear Size: 35 g
$4.95
Bostik Pink Stik is a neat, no-mess glue stick that goes on pink so coverage is easy to see, and dries pink to add fun colour to your creations. Perfect for school projects, craft, scrapbooking and everyday office use. Why you will love it Goes on pink and dries pink Smooth application with quick grab Non toxic and acid free Low mess twist up tube Washable from hands and most fabrics Best for Paper, card and photos School assignments and scrapbooks Office presentations and collages How to use Ensure surfaces are clean, dry and free from dust. Twist up a small amount of glue and apply a thin, even coat to one surface. Join surfaces and press firmly. For heavier card, apply to both surfaces. Replace cap after use to prevent drying out. Clean up and safety Fresh glue washes off skin with soap and water. Wipe excess from surfaces with a damp cloth before it dries. Keep out of reach of young children when not in use. Specifications Brand Bostik Product Pink Stik Glue Stick Size 35 g Colour (wet) Pink Colour (dry) Pink Suitable materials Paper, card, photos, light fabrics Not recommended for glossy plastics, foam, or other non porous surfaces where a stronger adhesive is required.
$4.95
You have seen 192 out of 324 products
Kneadable putties and hand-moulded compounds for shaping, patching and quick repairs. Wear gloves, mix to a uniform colour, and apply within the working time; many can be sanded/painted after cure. Use filters to refine by chemistry, set speed and temperature rating. Always consult the product page and TDS/SDS.
