In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gorilla Clear Grip® is a flexible, fast-setting, crystal clear contact adhesive that creates a strong, permanent bond. Gorilla Clear Grip® is paintable and waterproof making it great for projects both inside and out! Build, Repair, Craft™
PRODUCT FEATURES
WATERPROOF – For indoor/outdoor use
FAST GRAB – Holds in just seconds
PERMANENT BOND
FLEXIBLE
CRYSTAL CLEAR
HEAVY DUTY
NO-RUN FORMULA
PAINTABLE
PHOTO SAFE
WASHER & DRYER SAFE
BONDS: Metal, Glass, Fabric, Wood, Ceramic, Leather, Paper, Plastic*, and More!
*Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces.
All surfaces should be clean and free of dirt, grease and oil. Best if used between 10°C and 32.2°C. Clear Grip® should only be used in a well ventilated area.
Apply adhesive to each surface to be bonded.
To maximize bond strength: Wait approximately two minutes for adhesive to partially dry before joining surfaces.
Press surfaces firmly together.
NOTE: Bond forms immediately and can be difficult to reposition.
Cure Time
Allow for a minimum of 24 hours for full cure. Cure time may increase with lower temperatures and when used on non-porous surfaces.
Storage Tips
After each use, wipe nozzle with a dry cloth and tightly replace cap. Store in a cool, dry location. Tip: For easier re-opening, apply a thin coat of petroleum jelly to the threads before replacing cap. Store away from children and animals.
Clean-up
Wipe uncured adhesive with a dry cloth and clean with acetone, isopropyl alcohol, or citrus based solvents according to manufacturer’s instructions. Cured adhesive may be removed by scraping from surface.
Paintable
When fully cured.
*NOTE: Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces.
TECHNICAL SPECS
APPLICATION TEMPERATURE – 10° to 32.2° C, best at room temperature
OUTDOOR – Yes
MOISTURE RESISTANT – Waterproof
PAINTABLE – Yes – Can be painted with water and oil based paints, spray paint
SANDABLE – Yes
STAINABLE – Yes
CURED COLOR – Clear
STORAGE TIPS – Flammable adhesive, do not use or store near heat, sparks, flames, or while smoking. Store in a cool, dry location. Wipe nozzle clean before replacing cap, for easy re-open apply a thin coat of petroleum jelly to threads.
GAP FILLING – No
PHOTO SAFE – Yes
WASHER & DRYER SAFE – Yes
How should Gorilla Clear Grip® be stored?
After each use, wipe nozzle with a dry cloth and tightly replace cap. Store in a cool, dry location. Tip: for easier re-opening, apply a thin coat of petroleum jelly to the threads before replacing cap.
What surfaces does Clear Grip® adhere to?
Gorilla Clear Grip® can be adhered to many surfaces including:
Wood, Metal, Stone, Ceramic, Glass, Plastic*, PVC, Brick, Concrete, Foam, Paper, Rubber, Fabric, and Laminate.
*NOTE: Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces.
Is Gorilla Clear Grip® food safe?
Clear Grip® should not be used around food.
How do you clean up Gorilla Clear Grip®?
When using Clear Grip®, it is best to wear safety glasses and chemical resistant gloves.
To clean uncured adhesive: wipe uncured adhesive with a dry cloth and clean with acetone, isopropyl alcohol, or citrus based solvents according to manufacturer’s instructions. Cured adhesive may be removed by scraping from surface.
See first aid treatment for skin contact.
Is Gorilla Clear Grip® gap filling?
No
Is Gorilla Clear Grip® UV Resistant?
Yes
Can Gorilla Clear Grip® be used both indoors and outdoors?
Yes, Gorilla Clear Grip® can be used both indoors and outdoors.
Is Gorilla Clear Grip® stainable?
Yes, Gorilla Clear Grip® is stainable when fully cured.
Is Gorilla Clear Grip® sandable?
Yes, cured Gorilla Clear Grip® is sandable.
Is Gorilla Clear Grip® paintable?
Yes, when fully cured.
Is Gorilla Clear Grip® Washer/Dryer safe?
Yes
Is Gorilla Clear Grip® photo safe?
Gorilla Clear Grip® is safe to use with photos.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gorilla takes epoxy to a new level—the Gorilla Tough level. With its superior solvent and water resistance, Gorilla Epoxy adhesive is incredibly strong and durable for household and automotive repairs alike. The easy-to-use syringe keeps the epoxy resin and hardener separate, so it is easy to dispense and won’t harden over time. The two-part, gap-filling formula easily bonds steel, aluminum, glass, wood, ceramic, tile and most plastics. Plus, it dries in an ideal, crystal-clear finish that makes projects look spotless.
Features:
Dries Clear: Ideal for clean, easy finishing
5 Minute Set: Plenty of repositioning time for the perfect fit.
Gap-Filling: Fills voids and bonds uneven and vertical surfaces.
Water Resistant: Withstands moderate exposure to water
Solvent resistant
Non-Toxic once cured
Easy-to-use syringe: Separate barrels of epoxy resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses.
Directions
Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together.
Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded.
Prepare Your Work Area and the Surface
If you’re using Gorilla Epoxy for the first time, or bonding a new type of material, we always recommend trying a test piece first.
Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together.
Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded.
Mixing Gorilla Epoxy
Remove the black cap from the two syringes. With tip pointing upward, cut or snap the end from tip of the syringes. With the tip still pointing upward, eliminate air and ensure even dispensing by slowly pushing the plunger until both the resin and the hardener are at the tip
Push the plunger to dispense even amounts of resin and hardener onto a clean, disposable, contained surface. The package itself can be used as a mixing tray. If you flip the plastic blister shell over, you can use the small well as a starter dish to begin dispensing until both the resin and hardener are flowing equally. Once the flow is even, move to the larger mixing well to dispense your even ratio.
Mix the two parts for about 20 seconds, until the mixture is uniform. Apply within 5 minutes.As you mix, you will notice that the epoxy warms up. This is a reaction that occurs as the resin and hardener combine.
Application
After mixing is complete, apply Gorilla Epoxy within 5 minutes. The epoxy mixture will continue to thicken and the bond strength will decrease the longer you wait to apply.
Clamping
To reach maximum bond strength, clamp project together and leave undisturbed.
Important Cure Times
Set: 5 minutes to apply and position
Handling: Allow to cure for 30 minutes undisturbed (no weight or handling)
Final Cure: Allow 24 hours for load-bearing weight
Storage: To close, pull plunger slightly back. Wipe tip clean with dry cloth and align notch on tip and cap. Close tightly.
Visit our FAQs for more information on what surfaces Gorilla Epoxy will bond, clean up information and more.
FAQ
Is Gorilla Epoxy gap filling?
Yes. Gorilla Epoxy is gap filling. It will fill voids and bond uneven and vertical surfaces. If filling gaps outdoors, note that Gorilla Epoxy may yellow over time with exposure to sunlight.
What is the shelf life? Are there storage tips to extend the shelf life?
Shelf life for Gorilla Epoxy is a maximum of two years. The adhesive is not activated until the resin and hardener come in contact with one another, so the shelf life is likely to be much longer if the epoxy tip is wiped clean after each use and the cap is securely replaced. Make sure you notice the notch on the cap and be sure to align that with the notch on the syringe tip. This will further ensure the two parts do not accidentally mix.
What is the best application temperature?
For best results, apply in room temperature situations. Application in cold temperatures will slow the cure time of Gorilla Epoxy, while application in hot temperatures can speed up the cure time.
Gorilla Epoxy’s cured bond withstands temperatures ranging from -23° to 82°C
Do I need to use clamps with Gorilla Epoxy? How long?
Clamps are recommended for use during setup to ensure the bond sets correctly.
Set Time: 5 minutes to mix, apply and position
Handling Time: Leave 30 minutes undisturbed (clamping is recommended)
Full Cure Time: 24 hours for load-bearing weight
How much Gorilla Epoxy do I apply?
Gorilla Epoxy is a very strong adhesive. It does not take a lot to get a strong bond.
Average coverage from our 25 mL epoxy syringe will cover 100 square inches.
What can I use as a mixing tray or stir stick?
A mixing tray and stir stick will be included in your Gorilla Epoxy package. Other ideas for mixing trays include aluminum foil trays, cardboard, or paper/plastic plates. Try using popsicle sticks, plastic utensils or straws for mixing.
What is Gorilla Epoxy?
Gorilla Epoxy is a two-part formula that requires equal parts of resin and hardener mixed together for activation. For best strength results, mix a 1-to-1 ratio of resin and hardener. Once mixed, Gorilla Epoxy is capable of bonding many materials and offers high strength results.
How do I remove Gorilla Epoxy?
Gorilla Epoxy is a very strong adhesive and is solvent resistant. Removing dried adhesive is difficult to do. Acetone will soften the epoxy; however, full removal will require mechanical means, such as scraping, rubbing, or sanding.
Uncured Removal:
Skin: Acetone, isopropyl alcohol, 2–3 washings with soap and water. Reminder: Cured glue requires mechanical means, such as rubbing or washing with exfoliating soaps.
Hair: Isopropyl alcohol
Clothes and Carpet: Isopropyl alcohol. For clothes and carpet, avoid acetone, soap and water, and mineral spirits, as they will not work well on fabric.
What surfaces will Gorilla Epoxy bond?
Gorilla Epoxy is very versatile. It boasts high-strength results for steel, wood, aluminum, ceramic, tile, glass, most plastics, pressure-treated lumber and much more!
What surfaces will Gorilla Epoxy bond?
Gorilla Epoxy is water resistant, which means it will resist moderate exposure to water but should not be fully submerged. If you need an adhesive that is 100% waterproof, check out our Original Gorilla Glue®.
How do I dispense Gorilla Epoxy?
Make sure all surfaces are clean, dry and free of oil. To improve adhesion, roughen up smooth surfaces with sandpaper before gluing. Remove black cap from the middle of the plunger. With tip pointing upward, snap end from the tip of the syringe. Slowly push plunger until resin and hardener are at the tip, then dispense evenly. The package blister can be used as a mixing tray. Mix for at least 20 seconds until the mixture is uniform. Apply to surface within 5 minutes. Clamp surfaces together or leave undisturbed for 30 minutes. To close, pull plunger slightly back. Wipe syringe tip with a clean, dry cloth then snap the black cap on tightly.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
APPLICATION
1. Pierce seal at end of tube by turning nozzle and cap clockwise.
2. Ensure the working surface is clean, dry, free of dust or any grease. 3. Apply adhesive sparingly to one surface only.
4. Place surfaces together and press firmly for 10 - 60 seconds. Adequate for practical purposes after 30 minutes
STORAGE:
5. After use. clean nozzle immediately with a cloth, replace cap and store upright between 5- 25°C. Avoid strong light and heat sources
LIMITATION:
Not recommended for polyethylene, polyester plastic & glass. Not suitable for use on items which contain hot liquids eg. Cups, mugs. May cause leather to discolour or harden. Test on a hidden area before use if in doubt. For interior use only.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
APPLICATION
1. Pierce seal at end of tube by turning nozzle and cap clockwise.
2. Ensure the working surface is clean, dry, free of dust or any grease. 3. Apply adhesive sparingly to one surface only.
4. Place surfaces together and press firmly for 10 - 60 seconds. Adequate for practical purposes after 30 minutes
STORAGE:
5. After use. clean nozzle immediately with a cloth, replace cap and store upright between 5- 25°C. Avoid strong light and heat sources
LIMITATION:
Not recommended for polyethylene, polyester plastic & glass. Not suitable for use on items which contain hot liquids eg. Cups, mugs. May cause leather to discolour or harden. Test on a hidden area before use if in doubt. For interior use only.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Repositionable Dots™ Dot N Go® dispenser fits in the palm of your hand and can be used as a 'second set of hands' to hold small, lightweight items in place temporarily. It's perfect for quick fixes and repairs around the home.
Not recommended for heavy or bulky materials that require a permanent bond.
Glue Strength - Temporary
Features/Benefits:
Hand-held Dispenser | Easy to Use
Acid-Free | Photo Safe
Non-Toxic | Kid Friendly
Instant Bond | Mess Free
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Glue Dots® Advanced Strength Double-Sided Sheets can be custom cut to any size or shape to provide adhesive coverage for projects both big and small. Ideal for tough jobs and DIY projects that require exceptional holding power.
Not recommended for temporary applications or delicate items.
Glue Strength - Super-Strength (Holds up to 8 lbs.)
Features/Benefits:
Resealable Bag | Easy to Store
Acid-Free | Photo Safe
Non-Toxic | Kid Friendly
Instant Bond | Mess Free
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bostik Hot Melt Sticks are made of a general purpose translucent flexible hot melt in a stick form for use with the Bostik Hot Melt Glue Gun. It provides an instant, fast, clean and versatile bond between a myriad of household and craft materials and suitable for many porous materials.
Recommended Uses
Ideal for:
Craft projects
Home décor projects
Minor household repairs
DIY projects
Materials
Designed to stick to:
Most craft and household materials
Fabric
Wood
Leather
Most plastics
Polystyrene
Ceramics
Features
Once heated and gunned out, it provides instant adhesion
Adhesive is clear and flexible when dry
Fast, clean and versatile
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
These non-yellowing dots are easy to use, acid and lignin free, making them ideal for use in the home, office and school as an alternative to drawing pins, staples or tape. They are solvent-free and non-toxic. Bostik Glu Dots are also available in an extra strength version, for permanent applications.
Key Features
Repositionable
Transparent, non-visible
Solvent-free and non-toxic
Acid and lingin free, suitable for photographs
Description
Bostik Removable Glu Dots are little circles of double-sided, clear adhesive which stick almost anything including paper, wood, plastic, metal, glass and painted surfaces. These non-yellowing dots are easy to use, acid and lignin free, making them ideal for use in the home, office and school as an alternative to drawing pins, staples or tape. They are solvent free and non-toxic. Bostik Glu Dots are also available in an EXTRA STRENGTH version, for permanent applications.
APPLICATIONS
- Holding up posters, cards, certificates, notices, maps, menus, calendars,
messages, timetables, learning aids, children paintings, decorations, etc.
- Keeping in place telephones, mouse pads, pens, candles, figurines, vases, calculators, ornaments, etc.
- Keeping picture frames straight.
- Sticking photos in an album.
- Ideal for school projects, scrapbooking, art and craft projects.
ADHESION
Bostik Removable Glu Dots sticks extremely well to non-porous surfaces such as metal, glass, plastics, vinyl coated and painted surfaces and porous surfaces such as paper, boards, cloth, and wood.
LIMITATIONS
- Not suitable for highly absorbent, damp or dusty surfaces.
- Not suitable for holding up heavy objects.
- May damage delicate papers on removal.
Safety Instructions:
Bostik Removable Glu Dots is non-toxic. The product poses a choking hazard if ingested. In the event of ingestion, the mouth should be washed with water. Seek medical assistance if irritation or discomfort persists.
Refer to our Safety Data Sheet for further toxicological information and comprehensive handling instructions.
Surface Preparation:
Ensure that surfaces are clean, dry and free of any dust, grease and loose materials.
How to Use:
1. Tear along the perforations.
2. Peel off the paper backing.
3. Press the dot firmly onto the first surface.
4. Remove the clear film.
5. Press the second surface firmly onto the dot.
6. Reposition if necessary
Cleaning
Remove dots carefully by rubbing and rolling them off. Use mineral turpentine to remove any remaining residue.
Storage
The shelf life of the product is indefinite if stored at room temperature.
Packaging
64 Glu Dots in a wallet
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
These non-yellowing dots are easy to use, acid and lignin free, making them ideal for use in the home, office and school as an alternative to drawing pins, staples or tape. They are solvent-free and non-toxic. Bostik Glu Dots are also available in an extra strength version, for permanent applications.
Ket Features:
-Repositionable
-Transparent, non-visible
-Solvent-free and non-toxic
-Acid and lingin free, suitable for photographs
Description
Bostik Extra Strength Glu Dots are little circles of double-sided, clear adhesive which exhibit high tack, offering secure bonds to almost anything including paper, wood, plastic, metal, glass and painted surfaces. These non-yellowing dots are designed to provide a permanent hold and the bond strength will increase over time. They are easy to use, acid and lignin free, making them ideal for use in the home, office and school as an alternative to drawing pins, staples or tape. They are solvent free and non-toxic. Bostik Glu Dots are also available in a REMOVABLE version, for non-permanent applications.
Applications
- Holding up posters, cards, certificates, notices, maps, menus, calendars, messages, timetables, learning aids, children paintings, decorations, etc.
- Keeping in place telephones, mouse pads, pens, candles, figurines, vases, calculators, ornaments, etc.
- Keeping picture frames straight.
- Sticking photos in an album.
- Ideal for school projects, scrapbooking, art and craft projects.
Adhesion
Bostik Extra Strength Glu Dots Stick extremely well to non-porous surfaces such as metal, glass, plastics, vinyl coated and painted surfaces and porous surfaces such as paper, boards, cloth, and wood.
Limitations
- Not suitable for highly absorbent, damp or dusty surfaces.
- Not suitable for holding up heavy objects.
- May damage delicate papers on removal.
Safety Instructions
Bostik Extra Strength Glu Dots is non-toxic. The product poses a choking hazard if ingested. In the event of ingestion, the mouth should be washed with water. Seek medical assistance if irritation or discomfort persists. Refer to our Safety Data Sheet for further toxicological information and comprehensive handling instructions.
Surface Preparation
Ensure that surfaces are clean, dry and free of any dust, grease and loose materials.
How to use
1. Tear along the perforations.
2. Peel off the paper backing.
3. Press the dot firmly onto the first surface.
4. Remove the clear film.
5. Press the second surface firmly onto the dot.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours.
Features
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Very quick setting in 90 seconds
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling
Good chemical resistance
Where can this product be used?
General small household repairs
Fixing gemstones to mounts
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Most Plastics
How to use this product
General Use
Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
All traces of grease, rust paint, etc. should be removed.
For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately.
Ensure correct caps are replaced on each tube or they will adhere.
Handy tips
Note: For information on how to identify plastics refer to the Selleys plastics guide.
For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap.
When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
Wipe off any uncured Araldite with acetone or nail polish remover.
To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Clamping recommended for a stronger bond.
Singles are great for those unexpected household breakages, so keep a couple at home just in case.
Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
Fast-acting solutions for quick repairs and production tasks. Great for small parts and close-fit joints; consider gels for vertical surfaces. Use filters to refine by chemistry and set time. Always check the product page and TDS/SDS.
