Dunlop Premixed Resaflex Tile Adhesive 1 kg Overview Dunlop Premixed Resaflex Tile Adhesive 1 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$22.68
Dunlop Wall Tile Adhesive 5.5 kg Overview Dunlop Wall Tile Adhesive 5.5 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$59.96
Sika AnchorFix-1 Grey Structural Adhesive 300 ml Overview Sika AnchorFix-1 Grey Structural Adhesive 300 ml is a high quality chemical anchoring adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials concrete masonry natural stone hollow substrates with sleeves Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Observe minimum bond and substrate temperatures specified by the manufacturer. Keep resin warm in cold weather. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Cure time depends on substrate temperature. At 20°C typical cure is within a few hours. Do not load anchors until fully cured. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Wipe uncured resin with appropriate solvent. Once cured, it is chemically resistant and must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$34.90
Gyprock CSR Acrylic Stud Adhesive 1 kg is a reliable acrylic stud adhesive for secure plasterboard fixing chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 1 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Gyprock CSR CSR for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Gyprock CSR Acrylic Stud Adhesive 1 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Fixing plasterboard to studs and battens Reducing the chance of nail pops and drumminess Suitable surfaces The adhesive works well on the following surface types when properly prepared: Timber framing and battens Metal studs as directed by code Back of plasterboard Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of install sheets within the wet time window. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Apply daubs as specified, then fix sheets with screws or nails. Adhesive cures to a resilient bond that complements mechanical fastening. Temperature and environmental performance Use in moderate temperatures for consistent cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean fresh residue with a damp cloth. Scrape away cured beads before setting coats. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed. Do not allow to skin in the tub. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$23.57
![Bostik Blu Stik Glue Sticks 35g [10 Pack]](http://gluesaustralia.com.au/cdn/shop/files/3247a52b-3527-4297-825a-a050176be4e8_d6fe2015-9cbc-4930-b3d1-683224070b7d.png?v=1760577211&width=645)
Key features Goes on blue, dries clear for easy, mess free gluing Non toxic, acid free and solvent free Fast drying with a strong hold on porous materials Allows brief repositioning before it sets Twist up stick with tight sealing cap to prevent drying out Low mess and easy to use for kids and adults Great value multi pack for classrooms and home offices Ideal for Paper and cardboard Photos and craft paper Lightweight fabric embellishments School assignments, posters and scrapbooks Directions Surfaces should be clean, dry and free of dust. Uncap and twist the base to raise the glue. Apply a thin, even layer to one surface. Join parts and press firmly for several seconds. Allow to dry. Full strength is reached after the glue has set clear. Clean up and safety Wipe fresh residue with a damp cloth. Wash hands and tools with warm soapy water. Keep capped when not in use. Keep out of reach of young children. Good to know Not recommended for non porous surfaces like metal or glass. For best results, store in a cool, dry place. Pack contents 10 glue sticks x 35 g each.
$33.50
Bostik Green Stik is an easy to use glue stick for everyday crafting, school projects, and office tasks. It applies smoothly, goes on clear, and dries clear for a neat finish. Why you will love it Non toxic and acid free Smooth application with strong initial tack Ideal for paper crafting, cut and paste, and classroom use Low mess and easy to control for kids and adults Surfaces Paper Cardboard Light fabric and similar porous materials How to use Ensure surfaces are clean, dry, and free from dust. Twist the base to raise the glue. Apply a thin, even layer to one surface. Press surfaces together firmly for several seconds. Allow to dry. For best results on heavier paper, apply to both surfaces. Clean up Wipe away excess with a damp cloth while still wet. Allow to dry fully before handling. Environment and packaging Formulated with a high percentage of natural ingredients Packaged in a recycled plastic container with soy ink label Packaging is curbside recyclable in many areas when the lid is attached Good to know Colour when applied: clear Dries: clear Size: 35 g
$4.95
Bostik Pink Stik is a neat, no-mess glue stick that goes on pink so coverage is easy to see, and dries pink to add fun colour to your creations. Perfect for school projects, craft, scrapbooking and everyday office use. Why you will love it Goes on pink and dries pink Smooth application with quick grab Non toxic and acid free Low mess twist up tube Washable from hands and most fabrics Best for Paper, card and photos School assignments and scrapbooks Office presentations and collages How to use Ensure surfaces are clean, dry and free from dust. Twist up a small amount of glue and apply a thin, even coat to one surface. Join surfaces and press firmly. For heavier card, apply to both surfaces. Replace cap after use to prevent drying out. Clean up and safety Fresh glue washes off skin with soap and water. Wipe excess from surfaces with a damp cloth before it dries. Keep out of reach of young children when not in use. Specifications Brand Bostik Product Pink Stik Glue Stick Size 35 g Colour (wet) Pink Colour (dry) Pink Suitable materials Paper, card, photos, light fabrics Not recommended for glossy plastics, foam, or other non porous surfaces where a stronger adhesive is required.
$4.95
![Bostik Blu Tack Reusable Adhesive 75g [Pink]](http://gluesaustralia.com.au/cdn/shop/files/BOBLUTACGN_05.jpg?v=1760306853&width=645)
Why you will love it Reusable and repositionable No pins or tape required Low mess with easy clean up Holds posters, photos, notes, and lightweight items Malleable for custom shapes and small gap fixes Ideal uses Posters and signs on painted walls, tiles, glass, and metal Securing items on desks and shelves Keeping cables tidy and in place Crafts, school projects, and model making How to use Ensure surfaces are clean, dry, and free from dust or grease. Pinch off a small piece and knead until soft and warm. Form into a ball and place on the item to be mounted. Press firmly to create a good bond. Use more for heavier items. Removal tips Peel off slowly by rolling the adhesive away from the surface. If residue remains, dab with a fresh piece to lift it. Test on delicate or matte paints in an inconspicuous area first. Good to know Not suitable for highly absorbent, recently painted, or dusty surfaces. Avoid use on silk screens, flocked or delicate wallpapers, and porous finishes. Store in a cool place inside the pack for best performance. Specifications Type Reusable adhesive putty Colour Pink Pack size 75 g
$6.50
![Bostik Blu Tack Reusable Adhesive 75g [Yellow]](http://gluesaustralia.com.au/cdn/shop/files/BOBLUTACGN_06.jpg?v=1760306777&width=645)
Why you will love it Reusable and repositionable No pins or tape required Low mess with easy clean up Holds posters, photos, notes, and lightweight items Malleable for custom shapes and small gap fixes Ideal uses Posters and signs on painted walls, tiles, glass, and metal Securing items on desks and shelves Keeping cables tidy and in place Crafts, school projects, and model making How to use Ensure surfaces are clean, dry, and free from dust or grease. Pinch off a small piece and knead until soft and warm. Form into a ball and place on the item to be mounted. Press firmly to create a good bond. Use more for heavier items. Removal tips Peel off slowly by rolling the adhesive away from the surface. If residue remains, dab with a fresh piece to lift it. Test on delicate or matte paints in an inconspicuous area first. Good to know Not suitable for highly absorbent, recently painted, or dusty surfaces. Avoid use on silk screens, flocked or delicate wallpapers, and porous finishes. Store in a cool place inside the pack for best performance. Specifications Type Reusable adhesive putty Colour Yellow Pack size 75 g
$6.50
![Bostik Blu Tack Reusable Adhesive 75g [Green]](http://gluesaustralia.com.au/cdn/shop/files/BOBLUTACGN_03.jpg?v=1760306665&width=645)
Why you will love it Reusable and repositionable No pins or tape required Low mess with easy clean up Holds posters, photos, notes, and lightweight items Malleable for custom shapes and small gap fixes Ideal uses Posters and signs on painted walls, tiles, glass, and metal Securing items on desks and shelves Keeping cables tidy and in place Crafts, school projects, and model making How to use Ensure surfaces are clean, dry, and free from dust or grease. Pinch off a small piece and knead until soft and warm. Form into a ball and place on the item to be mounted. Press firmly to create a good bond. Use more for heavier items. Removal tips Peel off slowly by rolling the adhesive away from the surface. If residue remains, dab with a fresh piece to lift it. Test on delicate or matte paints in an inconspicuous area first. Good to know Not suitable for highly absorbent, recently painted, or dusty surfaces. Avoid use on silk screens, flocked or delicate wallpapers, and porous finishes. Store in a cool place inside the pack for best performance. Specifications Type Reusable adhesive putty Colour Green Pack size 75 g
$6.50
![Bostik Blu Tack Reusable Adhesive 75g [Orange]](http://gluesaustralia.com.au/cdn/shop/files/BOBLUTACGN_04.jpg?v=1760306533&width=645)
Why you will love it Reusable and repositionable No pins or tape required Low mess with easy clean up Holds posters, photos, notes, and lightweight items Malleable for custom shapes and small gap fixes Ideal uses Posters and signs on painted walls, tiles, glass, and metal Securing items on desks and shelves Keeping cables tidy and in place Crafts, school projects, and model making How to use Ensure surfaces are clean, dry, and free from dust or grease. Pinch off a small piece and knead until soft and warm. Form into a ball and place on the item to be mounted. Press firmly to create a good bond. Use more for heavier items. Removal tips Peel off slowly by rolling the adhesive away from the surface. If residue remains, dab with a fresh piece to lift it. Test on delicate or matte paints in an inconspicuous area first. Good to know Not suitable for highly absorbent, recently painted, or dusty surfaces. Avoid use on silk screens, flocked or delicate wallpapers, and porous finishes. Store in a cool place inside the pack for best performance. Specifications Type Reusable adhesive putty Colour Orange Pack size 75 g
$6.50
Key features Dries clear for a neat, invisible finish Non toxic and low odour Water based for easy clean up before curing Suitable for brush or nozzle application Paintable when dry Strong bond on porous surfaces Ideal for Paper, cardboard, photos, and scrapbooking Craft foam, felt, and fabric edge bonding Balsa wood and other light timbers School and hobby projects Directions Ensure surfaces are clean, dry, and free of dust or oil. Apply a thin, even coat to one surface. For very porous materials, coat both surfaces. Join pieces while the glue is wet and press firmly. Clamp or weight if needed. Wipe away excess with a damp cloth. Allow to set. Light handling is typically possible after 30 to 60 minutes. Full strength develops after 24 hours. Clean up Clean tools and fresh spills with a damp cloth. Once cured, scraping or sanding may be required. Handy tips For stronger joints on timber, lightly sand and dry fit pieces before gluing. Avoid excessive glue, which can lead to slow drying and warping on thin paper. Not suitable for continuous water immersion or load bearing joins. Storage Replace cap after use. Store upright in a cool, dry place away from frost and direct heat. Safety Non toxic formula. If irritation occurs, discontinue use. Technical details Base PVA emulsion Appearance White, dries clear Viscosity Medium, smooth flow Open time Up to 10 minutes depending on surface and coat weight Set time Approx. 30 to 60 minutes Full cure 24 hours Water resistance Not recommended for prolonged moisture exposure Paintable Yes, once fully dry
$11.30
Bostik Hobby Craft Dual Tip Liquid Glue 30ml is the perfect choice for creative projects, crafts, and schoolwork. Designed for precision and versatility, this liquid glue features two applicator tips, a fine tip for detailed work and a broad tip for larger surfaces. The smooth, clear formula ensures a clean, professional finish without clumping or streaks. Dual applicator design: Fine and broad tips for all craft needs Clear drying: Leaves no visible residue Ideal for: Paper, cardboard, photos, and light craft materials Easy to use: Non-toxic, washable, and child-friendly Perfect for school and home projects This handy 30ml bottle is compact and easy to store, making it a must-have for hobbyists, students, and anyone who loves crafting. Its dual-tip applicator provides control and convenience whether you're gluing delicate details or covering larger areas. Applications: Arts and crafts, card making, scrapbooking, paper modeling, and DIY projects. Brand: Bostik
$5.88
Bring colour to craft time with Bostik Glu Stik Rainbow. These smooth-gliding, non toxic glue sticks make school projects, scrapbooks, posters and office tasks quick and tidy. They go on smoothly, dry clear and are washable from hands and most fabrics, making them ideal for kids and classrooms. Key features Vibrant rainbow set for fun, easy-to-see application Non toxic and solvent free for peace of mind Dries clear for a neat, professional finish Low mess stick format with twist up design Washable from hands and most washable fabrics Acid free formula suitable for photos and paper crafts Best for Paper, cardboard and lightweight craft foams School homework, posters and collages Scrapbooking and photo mounting Office and home stationery tasks How to use Ensure surfaces are clean, dry and free of dust. Twist base to expose glue and apply a thin, even coat to one surface. Press surfaces together and smooth from the center outward. Allow to dry. For heavier paper, hold or weight for a stronger bond. Clean up Wipe away excess with a damp cloth while wet. Wash hands with warm soapy water. On washable fabrics, pre treat with stain remover and launder according to garment instructions. Helpful tips Replace cap firmly after use to prevent drying out. Use on porous, lightweight materials only. Not suitable for metal, glass or heavy plastics. Test on a small area of delicate papers or photos first. Specifications Format Glue sticks Pack size 5 sticks Stick weight 35 g each Colour Rainbow set. Dries clear Solvent Solvent free pH Acid free Safety: Keep out of reach of young children when not in use. Do not ingest. If irritation occurs, discontinue use.
$18.00
Key features Goes on blue, dries clear for easy, mess free gluing Non toxic, acid free and solvent free Fast drying with a strong hold on porous materials Allows brief repositioning before it sets Twist up stick with tight sealing cap to prevent drying out Low mess and easy to use for kids and adults Great value multi pack for classrooms and home offices Ideal for Paper and cardboard Photos and craft paper Lightweight fabric embellishments School assignments, posters and scrapbooks Directions Surfaces should be clean, dry and free of dust. Uncap and twist the base to raise the glue. Apply a thin, even layer to one surface. Join parts and press firmly for several seconds. Allow to dry. Full strength is reached after the glue has set clear. Clean up and safety Wipe fresh residue with a damp cloth. Wash hands and tools with warm soapy water. Keep capped when not in use. Keep out of reach of young children. Good to know Not recommended for non porous surfaces like metal or glass. For best results, store in a cool, dry place. Pack contents 5 glue sticks x 35 g each.
$23.00
Bostik Glu Tape is a clean, quick and mess free double sided adhesive for everyday sticking and craft projects. At 6 mm wide and 12 m long, it gives precise control for cards, scrapbooks, posters, school projects and office tasks. Why you will love it Instant stick with no drying time Clean finish with no liquid glue spills Thin 6 mm width for neat, accurate placement Strong hold on most paper and lightweight materials Great for home, school and office use Great for Card making and scrapbooking Mounting photos, prints and posters Sealing envelopes and gift wrapping School assignments and craft projects Suitable surfaces Paper and cardboard Lightweight foam and foamboard Most coated papers and photo papers How to use Ensure surfaces are clean, dry and free of dust or oils. Apply the tape along the area to be bonded, pressing down firmly. Peel away the release liner if present, then align and press surfaces together. Rub over the bond area to secure a strong hold. Tips Test on delicate or coated papers before full application. For best results, apply at room temperature and avoid stretching the tape. Store in a cool, dry place out of direct sunlight. Specifications Type: Double sided adhesive tape Width: 6 mm Length: 12 m Color: Clear adhesive Pack contents: 1 roll
$10.60
Keep your glue gun ready for any project with the Bostik HG3 Glue Gun Refills. These high quality hot melt sticks provide a smooth, even flow for clean and reliable bonding. Pack of 10 clear adhesive sticks Compatible with Bostik HG3 Glue Gun Creates a strong, flexible and transparent bond Suitable for wood, plastic, fabric, leather, ceramics and more Perfect for craft work, household repairs and DIY projects. The hot melt formula ensures quick adhesion with minimal mess, giving you professional results every time. How to use: Insert a glue stick into the back of your glue gun. Allow the gun to heat for a few minutes before use. Apply steady pressure on the trigger to release glue. Join surfaces immediately for best results. Let the glue cool completely before handling. Safety Information: Hot glue can cause burns. Avoid contact with skin and eyes. Keep out of reach of children. The Bostik HG3 Glue Gun Refills are ideal for quick fixes, decorative projects and reliable everyday bonding.
$15.21
Key benefits Goes on purple, dries clear for easy, accurate application Low mess, quick grab on paper and card Washable formula that cleans up with water Solvent free and non toxic, suitable for school use Twist up stick for smooth, even coverage Great value multi pack for home, school, and office Best for Paper and cardboard Photos and scrapbooking Homework and classroom crafts Gift wrapping and arts projects How to use Ensure surfaces are clean, dry, and free from dust. Twist the base to raise the stick a few millimetres. Apply an even coat to one surface using light pressure. Join within 30 seconds and press firmly along the bond line. Allow to dry. Handling strength is reached in minutes, full bond develops as it cures. Clean up and storage Fresh residue wipes away with a damp cloth. Wash hands and tools with water. Replace cap after use to prevent drying out. Store upright in a cool, dry place. Typical details Format Solid glue stick Colour when applied Colours Colour when dry Clear Set time Minutes, depending on coat weight and ambient conditions Clean up Water while wet Suitable materials Paper, card, photos, light crafts Not recommended for Non porous surfaces, heavy materials, or outdoor use Pack contents 4 x 8 g glue sticks
$7.77
BBQ Tough Clean Grease & Grime Spray 400 g Bring your grill back to spotless condition with BBQ Tough Clean. This powerful, non-caustic formula is specially designed to lift away grease, fat, and charred food from BBQ plates, grills, and racks, giving you a cleaner and healthier cooking surface without harsh fumes. Key Benefits: Powerful cleaning: Penetrates and dissolves stubborn grease and grime. Spotless results: Leaves BBQ surfaces residue-free for safer cooking. Non-caustic & low fume: Safer to use around your outdoor cooking area. Cold application: Designed to work when the BBQ is cool (before use). Perfect For: Stainless steel and cast iron BBQ plates, grills, and racks Removing built-up food, grease, carbon deposits Deep cleaning before a big barbecue or regular maintenance How to Use: Make sure your BBQ is cold. Remove the racks, grills and plates if possible. Scrape off excess debris and wipe loose grease. Shake the can well and spray liberally onto the surface from upright position. Allow to sit at least 10 minutes (for tough grime, up to 2 hours), then wipe with a damp cloth or scouring pad. Rinse thoroughly with water and dry with a clean cloth. Optional: apply a light coat of cooking oil to surfaces to protect against corrosion. Important Safety & Usage Notes: Do not use on hot BBQs Avoid spraying on painted, plastic or aluminum surfaces. If overspray lands on unintended areas, wipe off immediately and rinse. Not intended for use on exterior, non-cooking surfaces (use an exterior BBQ cleaner for those parts). Keep out of reach of children and pets. Use protective gloves and avoid inhaling fumes.
$7.02
Overview This high-quality general-purpose silicone sealant is a versatile solution for a wide range of sealing and bonding applications. Engineered with neutral cure technology, it is designed to provide a durable, flexible, and weather-resistant seal that remains reliable even in demanding environments. Once cured, the sealant forms a strong rubber-like finish that is permanently elastic, ensuring long-lasting performance both indoors and outdoors. Key Features Neutral Cure Technology: Low-odor curing system suitable for sensitive applications. Permanently Flexible: Retains elasticity over time without cracking or shrinking. Waterproof Protection: Provides a watertight seal, protecting against leaks and moisture ingress. Interior & Exterior Use: Unaffected by rain, snow, extreme temperatures, or prolonged UV exposure. Excellent Adhesion: Bonds strongly to most common building materials without primer. Easy Application: Smooth flow from the tube, easy to tool and clean before curing. Applications This sealant is designed for general-purpose use across a variety of materials and environments. Its flexibility and adhesion make it suitable for: Sealing around window and door frames. Lap joints in metal guttering and roofing sheets. Bonding panels such as wood, plasterboard, insulation board, and drywall. Fixing masonry joints including sills, brickwork, and decorative trims. Gap filling around pipes, conduits, and penetration surfaces. General sealing in kitchens, bathrooms, and living areas where flexibility is required. Limitations Not suitable for permanent water immersion (e.g., underwater joints or continuous water load). Not recommended for use on polyethylene (PE), polypropylene (PP), polycarbonate (PC), polymethyl methacrylate (PMMA), PTFE, neoprene, bituminous surfaces, or very soft plastics. Not intended for deep cavity filling without adequate moisture for curing. Surface Preparation To ensure maximum performance, surfaces must be clean, dry, and free from dust, grease, or loose particles. Non-porous surfaces should be wiped with solvent and dried with a clean cloth. Porous surfaces should be lightly abraded or brushed to remove contaminants and improve adhesion. Complete any painting work before applying the sealant. Application Instructions Remove the cap and pierce the nozzle seal. Apply steadily along the joint or surface, ensuring continuous contact. Smooth or tool the bead before skin formation occurs. If masking tape is used, remove immediately after tooling to avoid tearing the cured seal. Curing At room temperature (23°C), the sealant will skin over within 15 minutes and achieve full cure within 24 hours, depending on humidity and joint depth. Once cured, it provides a permanently flexible and weatherproof joint. Cleaning & Maintenance Excess uncured sealant can be cleaned using a cloth dampened with mineral turpentine. Fully cured material should be trimmed away carefully with a sharp blade. Store unused tubes in a cool, dry place below 25°C and away from direct sunlight. Shelf life is up to 12 months from the date of manufacture. Health & Safety Use in a well-ventilated area. Avoid contact with eyes and mucous membranes, as uncured sealant may cause irritation. In case of contact with eyes, flush thoroughly with water and seek medical advice. Keep out of reach of children. Always follow safety instructions and refer to the product’s safety data for detailed guidance. Why Choose This General Purpose Silicone Sealant? This sealant is a trusted choice for tradespeople, DIY enthusiasts, and homeowners seeking a reliable solution for everyday sealing needs. Its combination of flexibility, adhesion, and weather resistance ensures that once applied, it continues to protect and bond effectively for years to come. Whether you are fixing a leaking gutter, sealing around windows, or bonding decorative trims, this product provides professional results with minimal effort. Technical Specifications Technology Neutral Cure Silicone Appearance Clear Paste Working Time Up to 15 minutes Tack-Free Time Approximately 15 minutes Full Cure at 23°C 24 hours Flexibility Permanently elastic after curing Weather Resistance Unaffected by rain, snow, UV, and temperature variations Applications Windows, doors, guttering, masonry, panels, pipes, decorative elements Storage Below 25°C, out of direct sunlight Shelf Life 12 months from manufacturing date
$9.98
UHU All Purpose Adhesives Super Strong & Safe, the super strong and super fast adhesive, which is adjustable - no instant finger bonding. Suitable for virtually all flexible, solid, porous and non-porous materials. Formula patented. Withstands vibrations and tremors. Moisture and heat resistant from -50°C to +100°C. Materials Universal - glues porcelain, ceramic, many plastic materials, metal, wood, glass, leather, rubber, Styrofoam®, paper, cardboard. Not suitable for leather clothing, textiles, PE and PP. Use and Handling Instructions Surfaces to be stuck together must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. Press parts together. Glue joint remains correctable for approx. 20 seconds. The thinner the film of adhesive, the stronger the bond.
$10.74
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$27.48
SikaBond® SprayFix: The Ultimate Aerosol Spray Adhesive for Multipurpose Use High-Performance, Fast-Drying, & Repositionable Adhesive SikaBond® SprayFix is your go-to aerosol spray adhesive for both temporary and permanent bonding. With its high performance, low odour, and fast-drying time, it's designed for your convenience. Key Advantages: Easy to use Low odour Dries clear Fast drying time (approximately 2-4 minutes) High initial strength Contains no chlorinated solvents - suitable for indoor use Repositionable for 1-2 minutes Applications Include: Upholstery Floor Repairs Furniture Lamination Art and Crafts (e.g., mounting prints) Suitable Substrates: Felts and Fabrics Metals Foams Cork Most Plastics Rubber Gaskets Fibreglass Wood (e.g., plywood, particle board) How to Use: Ensure the surface is clean, dry, and free of dust and grease. Shake the can well before use. Hold the can approximately 80-100 mm from the surface and spray lightly. Allow a few minutes for drying. Packaging: Available in 150g and 350g aerosol cans. Color: White when applied, clear when dry. Cleaning of Equipment: After use, invert the can and press the tip until clear propellant comes out for cleaning. Uncured overspray can be removed with Sika® Colma Cleaner or another suitable solvent.
$34.00
![Sika SikaSeal 300 Glass & Weather Seal [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/9318324011314_17b1b8c7-fa52-428b-bf6f-872b3b964d3b.png?v=1754711699&width=645)
Usage Aluminium Composite materials Panels(ACP) Glass Metals Coated and painted metals Plastics Wood Advantages Excellent adhesion High movement capability Weather resistant Outstanding UV resistance High strength Interior & Exterior Permanent flexibility Colour Transparent
$18.18
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$20.57
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/e477ca37aa8d409fa7f84e307b56d97a.jpg?v=1757752932&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$19.00
![Selleys No More Gaps Timber Floors x 380g [Walnut]](http://gluesaustralia.com.au/cdn/shop/files/169e8e96732544d89fdb6ec6deaba129.jpg?v=1757753052&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
![Selleys No More Gaps Timber Floors x 380g [Jarrah]](http://gluesaustralia.com.au/cdn/shop/files/42b566f39b234ffeab320faed408b86e.jpg?v=1757753057&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
![Selleys No More Gaps Timber Floors x 380g [Hardwood]](http://gluesaustralia.com.au/cdn/shop/files/5160e944b5d3493cbac2a999232381fa.jpg?v=1757753063&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$11.00
Liquid Nails Fast is a water-based high strength (*) construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. After drying it is beige (light tan) in colour. Uses Liquid Nails Fast has high initial (immediate) grab which reduces the need to support joins while the adhesive cures. The initial grab works best with porous surfaces. It will bond to many building materials including MDF, particle board, timber, plaster board, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results are achieved when at least one surface is porous. Liquid Nails Fast would typically be used for the following applications: Areas where nailing is not desirable Skirting boards, architraves, cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding minimises slippage when adhering on vertical surfaces Meets or exceeds AS 2329-1999 (Mastic adhesives for fixing wall boards) Does not drip, sag or string between panels Bridges gaps and will adhere materials with uneven surfaces Low mess – excess and squeeze out is easily cleaned up with wet cloth No solvent fumes – ideal for large indoor jobs High flexibility – will withstand thermal movement and vibration High heat resistance – will not lose bonds exposed to sun Paintable when dry Easy to extrude at all temperatures Application Tips Liquid Nails Fast should always be used in conjunction with permanent mechanical fasteners except in low stress applications such as wall panelling and fixing light weight objects. (Bonds may creep under constant heavy loads.) Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications. In cold or damp weather and between non-porous materials drying time is greatly extended Thick applications take longer to dry than thin applications Pre-test plastics to determine suitable bonding. Adheres well to UPVC. Not suitable for polyethylene and polypropylene. For wood flooring applications Liquid Nails (solvent based) is recommended. [Liquid Nails Fast is satisfactory for fixing sheet flooring (particleboard/ply) to joists in conjunction with the manufacturer’s minimum nailing specification but is not recommended for fixing sheet wood flooring to flat surfaces such as existing or concrete floors. Technical Details and Performance For porous substrates good bond strength is achieved after 24 hours and will continue to strengthen over 2-3 day period. Time for strong bond depends on nature and conditions of application. In cold or damp weather and between non-porous materials, drying time is greatly extended. Indicative information only, not to be used for setting specifications. Appearance Lump free, air-free smooth beige paste Specific Gravity Approx. 1.44g/mL @ 25oC Viscosity Typical 7000 – 9000 Poise Slump Typical: 0mm Shear Adhesion Strength (7 days) (AS2329) Greater than 1500kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure) Typical 40N/25mm (wire gauze off hoop pine.(Variant to AS2329)) Initial Bond Strength AS2329-1999D (Tested after 24 hrs) Over 200kPa Heat Resistance Bonds will resist temporary exposure to temperatures up to 140oC. Constant high temperatures will reduce constant load holding power (see below). Creep resistance (under constant load)*2 Fully cured *1 bonds of 625 sq. mm will hold up to 500g loads (7.8kPa) in shear at constant 80oC Fully cured *1 bonds of 625 sq.mm will hold up to 100kPa in shear at 25oC (equivalent to 6Kg load on 625 sq.mm bond area) Coverage 15 metres of a 5mm diameter bead 1mm thick bonds on porous substrates cured at least 7 days at temps above 25oC This data is provided as indicative only. Not to be used for design purposes. Thick bonds reduce constant load holding power and increase curing time. Larger bond areas increase curing time. Cleaning Liquid Nails Fast may be cleaned off with hot soapy water or a damp cloth while still wet. Dry adhesive is best removed by scraping or peeling.
$15.33
![Selleys Marine Flex For Boats Pools and Spas Water Proof [Black]](http://gluesaustralia.com.au/cdn/shop/files/f795ca009d10470fb346ebed4b3dc2a3.png?v=1757753303&width=645)
Selleys Marine Flex is a high-performance adhesive and sealant designed for marine and water-exposed applications. Using Sil-X advanced polymer technology, it provides a permanent watertight seal above and below the waterline, even in salt, fresh, or chlorinated water. Key Features Cures and bonds underwater No primer required for most surfaces Strong and flexible bond absorbs vibration and movement Solvent-free and isocyanate-free formulation Sandable once cured 10-year watertight seal guarantee (above waterline) Where to Use Ideal for marine, pool, spa, and construction projects where water exposure or movement is expected. Suitable for bonding and sealing: Boat hulls, fittings, and deck seams Pool tiles, coping, and skimmer boxes Concrete, fibreglass, sealed timber, and metal surfaces Glass, ceramics, and most rigid plastics Technical Details Technology Sil-X advanced polymer Colour White or Black Size 410g cartridge Finish Smooth, paintable once cured How to Apply Ensure surfaces are clean and free from grease, oil, or dust. Can be applied to damp or wet surfaces. Cut the nozzle to the desired bead size and apply using a standard caulking gun. Tool the sealant immediately with a soapy water solution before it begins to skin. Allow to cure fully before sanding or painting if required. Limitations Not suitable for polyethylene (PE), polypropylene (PP), or PTFE materials Gelcoat surfaces should be lightly sanded before application The watertight guarantee applies to applications above the waterline Why Choose Selleys Marine Flex When you need a sealant that can withstand constant water exposure, movement, and vibration, Selleys Marine Flex delivers unmatched reliability. It bonds powerfully, stays flexible, and ensures a lasting waterproof finish for marine, pool, or construction applications.
$28.00
Selleys Aquadhere Quick Set is a quick setting PVA wood glue that is suitable for all types of wood, sets twice as fast compared to normal PVAs and requires no clamping in many situations*. It will bond almost anything your craft work calls for! Features Fast bonding No clamping* Convenient and easy to use Non-toxic, water clean-up Dries clear *No need for clamping where joints are not under stress and timber is not bowed, warped etc Where can this product be used? School projects Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window frame Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Decorating What materials is this product suitable for? Interior wood Carboard Paper Fabric Felt Leather How to Use Surfaces to be bonded must be close fitting, dry and clean. Shake bottle and apply thinly to one surface. Press surfaces together firmly for 1-2 minutes. Wipe off excess adhesive with a damp cloth whilst still wet If joint is under stress or timber is bowed or warped, clamp until adhesive sets. Adhesive strength will be sufficient for object to be handled after 5-10 minutes for softwoods and 15-20 minutes for hardwoods. Allow 30-60 minutes before working with object. Maximum strength is attained in 4-8 hours. Allow longer setting/bonding time in cold or humid conditions. Limitations: Not for exterior use. Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere Quick Set is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Selleys Aquadhere exterior or Selleys Aquadhere Durabond). Will not take timber stains. Aquadhere Quick Set is not recommended for joints that are subjected to constant high stress. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Selleys Aquadhere Exterior.
$24.60
Selleys 655 FC Crystal Clear Flexible Adhesive and Sealant 290 mL Premium 100 percent crystal clear hybrid adhesive and sealant that delivers superior strength, instant grab, and long lasting flexibility. Bonds and seals on most common building materials, works indoors and outdoors, and can be applied to wet or damp surfaces. Low VOC, non yellowing, paintable, and non slumping for neat vertical and overhead joints up to 20 mm. Why you will love it Superior strength with instant grab Primerless adhesion on most surfaces Applies to wet or damp substrates Fast curing with non slumping finish Crystal clear appearance that stays clear Low VOC and isocyanate free Paintable with water based paints Suitable for interior and exterior use Where it works Ideal for sealing, bonding, and filling on concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles, fiberglass, and most plastics. Not recommended for polyethylene, polypropylene, or PTFE. Typical applications Clear sealing of kitchen and laundry splashbacks Bonding trims, panels, and skirtings Sealing gaps in windows, door frames, and cladding General construction and maintenance sealing where a clear finish is desired How to use Prepare the surface so it is clean and free from dust, grease, and loose material. Cut cartridge tip, attach nozzle, and load into a caulking gun. Cut nozzle to the required bead size. Apply a continuous bead, pressing firmly so the product contacts both sides of the joint. Tool with a soapy solution before skinning. For neat edges, mask before applying and remove tape before skin forms. Clean up Uncured product cleans off with mineral turps. Once cured, remove by scraping or sanding. A dedicated silicone and adhesive remover can assist. Good to know Do not paint with solvent based paints. If painting, first coat with a water based paint. Not suitable for permanent water immersion or below water line use. Store below 30°C. Use within 6 months after opening for best results. Specifications Technology Moisture curing silyl modified polymer Colour Clear Pack size 290 mL cartridge Density Approx. 1.06 g/mL Application temperature 5 to 35°C Tooling time at 23°C and 50 percent RH About 25 minutes Skin time at 23°C and 50 percent RH About 45 to 55 minutes Cure rate at 23°C and 50 percent RH Approx. 3 mm per 24 hours Slump 0 mm Tensile strength About 1 MPa Shore A hardness 30 ± 5 Elongation at break Approx. 130 percent Modulus at 100 percent elongation About 1.0 MPa Service temperature 0 to 70°C VOC content Approx. 35 g/L Safety Follow good ventilation and hygiene practices. Refer to the product safety data sheet for detailed advice.
$20.00
Selleys 650FC: The Ultimate Adhesive Sealant Powered by Advanced Hybrid Technology Key Features +/- 20% Joint movement capability Excellent UV & Weather Resistance Superior Strength & Instant Grab Can be applied on damp surfaces Applications This product can be used in various applications such as trafficable joints, air conditioning ducting, caravan construction, perimeter seals around doors, windows, and general interior joint sealing. Compatibility Highly compatible with most building materials including timber, concrete, metals, and more. Not suitable for PVC, polyethylene, and temperatures above 80°C. How to Use Ensure surfaces are clean and dry. Apply using a sealant gun and spread evenly within 10 minutes. Storage and Cleanup Store in cool, dry conditions below 30°C. Uncured product can be removed with mineral turps. Precautions This product is not suitable for constantly submerged joints or temperatures beyond 80°C.
$20.00
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$13.50
Polyfilla P10 Gap Filler Rapid: The Ultra-Fast Solution for Perfect Fills Features Flexible Smooth Finish Rapid Drying Paintable in 10 minutes* Low Shrinkage Crack-Resistant* Applications Ideal for filling gaps around cornices, wall joints, skirting boards, as well as inside windows and door frames. Usage Instructions *To avoid paint cracking, apply to gaps no larger than 5mm deep and 10mm wide at temperatures above 20°C. Allow the sealant to dry before painting. Avoid applying paint too thickly. When to Use Paintable in just 10 minutes, allowing for fast project completion.
$7.35
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Light Grey]](http://gluesaustralia.com.au/cdn/shop/files/9311531002762_be7a4237-355f-47f3-ae09-dabb40913652.png?v=1754712211&width=645)
$11.94
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Cedar]](http://gluesaustralia.com.au/cdn/shop/files/9311531002731_8a23516e-dc7a-4a74-9fda-5436c7c62091.jpg?v=1754712214&width=645)
$11.94
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Black]](http://gluesaustralia.com.au/cdn/shop/files/9311531002724_6b56cb9d-718d-4289-8566-b1965f6372f4.webp?v=1754712217&width=645)
$11.94
PC-Concrete ™ Anchoring and Crack Filling Epoxy— is the epoxy chosen to repair cracks in a warehouse and factory floors. Dispense and apply using a standard size caulking gun. Cures hard enough to drive over within 3 hours at standard temperature. Nothing stronger for your anchoring applications. PC-Concrete™ is a two-component (1:1 ratio), 100% solids, high modulus, and structural epoxy paste. PC-Concrete™ is a solvent-free, no odour, high strength, moisture insensitive epoxy system. The resin and hardener are uniformly dispensed from a 9-ounce cartridge system and mixed through a mixing nozzle using a standard size caulking gun. (We recommend at least an 18:1 thrust ratio). PC-Concrete™ is also provided in a 22-ounce dual cartridge system for Contractors and Professionals. This size requires a 600ml high thrust dual cartridge dispensing gun. For filling larger cracks and cavities use the 102-ounce bulk kit. PC- Concrete™ will NOT SHRINK. Suitable for Interior and Exterior applications. Can be applied to WET & UNDERWATER surfaces. Here are just a few specific uses (there are many other uses): Anchor into marine docks above or below waterline Anchor equipment to floors Bond to pre-stressed floors Anchor into stone and rock. Install anchor bolts for sill plates Anchor into foundations and block Fill cracks in concrete allowing equipment traffic In 4 hours Anchor into concrete railroad ties Anchor HVAC equipment to concrete pads and roofs Waterproof floor to wall cracks Re-anchor railing at convention center or apartment building Anchor seats in lecture hall or theaters Repair broken concrete in shopping mall parking garage Fill spalled concrete in car wash Fix fork truck damaged concrete in warehouse Seal crack in sanitation and chemical storage facility containment area Repair floor in fire station garage Anchor safe to floor prison and security pickproof epoxy Anchor machinery
$14.46
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$14.76
Sandable Paintable Ready mixed Weather resistant Parfix multipurpose filler is a versatile, ready mixed filler ideal for filling cracks, holes and gaps inside and outside the home. Sandable and paintable, it enables a smooth finish.
$24.94
![Monarch Mini Gap Filler [White]](http://gluesaustralia.com.au/cdn/shop/files/9320090029080_1b178ddb-e3de-4ec1-83bb-8e320595bdb3.jpg?v=1754712311&width=645)
$2.84
![Monarch Mini Gap Filler [Cream]](http://gluesaustralia.com.au/cdn/shop/files/9320090030581_c5a95353-e7ee-4d92-8445-93066291f976.jpg?v=1754712313&width=645)
$6.02
![Monarch Mini Gap Filler [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090030567_dd3b7bac-a9e5-4986-9275-2bff35fb52de.jpg?v=1754712316&width=645)
$6.02
Monarch Mini Fill Sand Go™ MONARCH MINI® FILL SAND GO™ is an all in one solution to almost every DIY filling repair job. It’s a quick-dry, ready mixed, water-based formula that is suitable for small to medium cracks and holes in plasterboard & timber surfaces. The innovative MONARCH MINI® FILL SAND GO™ is a 3 in 1 product solution that includes a filling blade applicator as well as an ingenious sanding tool with a reversible sanding sponge. This allows you to complete the filling repair from start to finish without the hassle of requiring extra tools. FEATURES Innovative 3 in 1 Solution Filler, Applicator & Sanding Puck with Sponge All included Suitable for Interior repairs on Plasterboard & Timber BENEFITS Quick Dry Formula Ready to Use Multi-Purpose Filler Paintable Sandable Low Shrinkage UV Resistant Low Odour
$14.04
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$21.72
You have seen 144 out of 159 products
Products formulated to reduce smell during application and cure, perfect for indoor projects and tight spaces. Ventilation is still recommended. Use filters to refine by chemistry, set speed and temperature rating. Always review the product page and TDS/SDS for handling and cure guidance.
