Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$26.05
Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$28.21
3 x 1g originally sealed tubes ideal portion for one application. in a handy storage box reaches the smallest corners and joints Extra strong super glue in 3 x 1g tubes, packaged in a small storage box, ensuring optimal quality for every new application. The liquid adhesive reaches the smallest corners and joints. Materials Glues many plastics, porcelain, ceramic, metal, wood and rubber. Not suitable for leather clothing, PE, PP nor styrofoam. Use and Handling Instructions Surfaces to be stuck together must fit exactly and must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. The thinner the film of adhesive, the stronger the bond. Press the parts together immediately and hold in place for a short time. Breathing upon the surfaces to be stuck will speed up bonding. After use, wipe the applicator tip dry and close firmly. Will last longer if stored in a cool place.
$11.50
PROPERTIES Extra strong Fast but temporarily adjustable Does not drip Ideal for porous materials and vertical surfaces Dishwasher proof and water resistant APPLICATION SUITABLE FOR: Ideal for small-area bonds. Glues almost all solid and flexible materials like ceramics, leather, rubber, many plastics (such as rigid PVC, ABS, PS, Plexiglas®, polycarbonate (Makrolon®), and phenolic resins (Bakelite®)), porcelain, metal, wood, cork, felt, and cloth (check suitability first). Only partly suitable for glass (over a certain period of time the bond becomes brittle, causing it to weaken). Ideal for porous materials. NOT SUITABLE FOR: Not suitable for PE, PP, silicone resins, PTFE, Styrofoam®, fabrics and leather clothing. BEFORE USE: Working conditions Do not use at temperatures below +10 °C. The glue responds best to an air humidity level of 50-70 %. Surface requirements Surfaces to be glued must be clean, dry, and free of dust and grease, and must fit exactly. Preliminary surface treatment Any dust, oil, grease, wax or separating agent should be thoroughly removed from the surfaces to be stuck together. The best way to achieve this is to rub the parts a number of times with appropriate solvents, such as acetone (if suitable for the material – check first!). For metals and metal alloys it is usually sufficient to roughen the surface using emery paper or by grinding or brushing. DURING USE: Directions for use 1. To pierce the membrane, turn the cap clockwise firmly onto the tube. Tip: do not press the tube while piercing. 2. Unscrew the cap to reveal the applicator. Apply the adhesive directly from the tube, using the nozzle, as thinly as possible onto one side (too much glue slows down the curing process significantly). Press parts together immediately. After use, clean nozzle with a dry tissue and replace cap. Advice When glueing at low humidity, curing time can be shortened by briefly breathing onto one of the parts to be assembled. The best glueing results are reached at room temperature. Points of attention Contains cyanoacrylate. Bonds skin and eyelids together in seconds. If product comes into contact with the eyes, rinse immediately with plenty of water and seek medical advice. In case of contact with skin, glue can be dissolved by soaking in warm soapy water. Then apply a skin cream. May cause respiratory irritation. Avoid breathing vapours. Keep out of the reach of children. AFTER USE: Stains/residue Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue but very slowly (check suitability first). Storage conditions Store in a dry, cool, frost-free place. Storage below +5 °C (in refrigerator) ensures maximum shelf life.
$7.00
Tarzan's Grip 5min Epoxy is a two-part all purpose adhesive. When mixed equally together it provides a tough, rigid, high strength bond to tackle the toughest DIY projects. Its also fast - sets in 5 minutes and reaches initial handling strength in 30 minutes. Easy mix Durable bond Dries clear Water resistant
$12.29
Why Choose Selleys Super Glue Adjustable Gel? Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes. Key Benefits: Adjustable Setting Time: Allows precise alignment before setting. Rapid Bonding: Bonds in 30 seconds for fast repairs. Versatile: Adheres to ceramics, china, metal, wood, and most plastics. Easy to Use: No mixing required, with a convenient gel formulation for clean application. Where Can This Product Be Used? Everyday household repairs on: Ceramic and China Metal and Wood Most Plastics* What Materials Is It Suitable For? Bonds a variety of porous and non-porous surfaces. Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers. How to Use Selleys Super Glue Adjustable Gel Prepare: Pierce the seal by attaching the nozzle with the cap and turning clockwise. Ensure surfaces are clean, dry, and free from dust, dirt, and grease. Apply: Apply a small amount of adhesive to the surfaces to be bonded. Press surfaces together gently and hold for several minutes to ensure sufficient bond strength. After Use: Wipe the nozzle clean with a cloth or paper. Replace the cap securely. Limitations Not suitable for use on leather, polyethylene, polypropylene, or PTFE. Will not permanently bond vessels exposed to water or dishwashers. Handy Tips for Best Results Ideal for vertical applications and slightly porous materials. Use 1 drop per cm² for optimal bonding. Sets in 30 seconds, achieving maximum bond strength in 24 hours. Clean-Up Instructions Wipe the tip of the tube with a cloth or paper after use. Replace the cap tightly to avoid drying out the product. Product Details Size: 3g Tube Colour: Clear Technology: Cyanoacrylate Recommended Use: Interior Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
$5.64
Why Choose Selleys Super Glue Adjustable Gel? Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes. Key Benefits: Adjustable Setting Time: Allows precise alignment before setting. Rapid Bonding: Bonds in 30 seconds for fast repairs. Versatile: Adheres to ceramics, china, metal, wood, and most plastics. Easy to Use: No mixing required, with a convenient gel formulation for clean application. Where Can This Product Be Used? Everyday household repairs on: Ceramic and China Metal and Wood Most Plastics* What Materials Is It Suitable For? Bonds a variety of porous and non-porous surfaces. Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers. How to Use Selleys Super Glue Adjustable Gel Prepare: Pierce the seal by attaching the nozzle with the cap and turning clockwise. Ensure surfaces are clean, dry, and free from dust, dirt, and grease. Apply: Apply a small amount of adhesive to the surfaces to be bonded. Press surfaces together gently and hold for several minutes to ensure sufficient bond strength. After Use: Wipe the nozzle clean with a cloth or paper. Replace the cap securely. Limitations Not suitable for use on leather, polyethylene, polypropylene, or PTFE. Will not permanently bond vessels exposed to water or dishwashers. Handy Tips for Best Results Ideal for vertical applications and slightly porous materials. Use 1 drop per cm² for optimal bonding. Sets in 30 seconds, achieving maximum bond strength in 24 hours. Clean-Up Instructions Wipe the tip of the tube with a cloth or paper after use. Replace the cap tightly to avoid drying out the product. Product Details Size: 1g Tube Colour: Clear Technology: Cyanoacrylate Recommended Use: Interior Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
$9.59
A strong, weather and impact resistant adhesive that is ideal for most shoe repairs. Features Easy to use Strong Flexible Bond Weather resistant Impact resistant Appearance Dries yellowish/beige Where can this product be used? Sole Tongue Strap Inner sole Attach beads, jewels, decorative items Will not bond Polyethylene or Polypropylene plastics. For these we recommend Selleys Plastics Glue. May not adhere to some plastic / rubber soles. What materials is this product suitable for? Leather Canvas Fabric Rubber Cork Most Plastics EVA foam (e.g Desert boots sole) How to use this product Ensure surfaces are clean, dry and free from dirt or grease. Remove cap and carefully pierce seal. For larger area repairs such as shoe soles, we recommend you use the contact bond method: For quick and even bonding, apply to one surface only, press together and pull apart. Keep apart until the adhesive film is almost dry (approx. 10 – 20 minutes). Carefully line up surfaces to be joined and press surfaces firmly together. Bonds immediately on contact. Clamping may be necessary in some applications. For smaller areas, either use the contact method as above, or join with a wet bond: Apply Shoe Glue to one surface only and immediately press together. Lightly clamp or hold until dry. Allow adhesive to achieve maximum bond strength (24 hours) before wearing your repaired shoe/s. Wipe nozzle clean and replace cap immediately after use. Clean up application tools and excess adhesive with turps before it dries. Handy tips A piece of plastic from a takeaway container makes a good applicator for shoe soles. Bulldog clips are handy to use for clamping straps and other small areas. Pack includes a removable nozzle for easy application.
$10.40
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$10.84
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$7.40
A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around the pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Appearance Translucent Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing a loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bonding sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from the nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured Araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquefy slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non-toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$70.21
Bonds most materials within 30 seconds The level of liquidity and lack of viscosity work best for applications where flexibility and seeping is required 25ml container Integrated nozzle for easy application Ritetite Turbo is a one-component liquid super glue that bonds extremely quickly. When it comes into contact with surface moisture, it hardens instantly. Its extremely fast curing qualities make it an excellent choice for high-speed industrial production, where an ultra-rapid-acting adhesive with low consistency and viscosity is required. Surface Preparation prior to bonding with RITETITE TURBO Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE TURBO Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$23.54
Bonds most materials within 30 seconds High-viscosity allows for greater accuracy and detail Large 100ml container Integrated nozzle for easy application Ritetite Control is a one-component gel super glue that bonds extremely quickly. It’s made with a specially designed thixotropic formula that instantly polymerises (hardens) by absorbing surface moisture. Its fast-curing properties make it an excellent choice for high-speed industrial applications that require a gel-like, viscous adhesive that does not spread or leak like traditional super glue. Ritetite Control works exceptionally well in poor-fitting applications such as rough metal or ceramic repairs, unfinished metal-to-metal bonding, and metal-to-rubber bonding due to its thick gel consistency. Surface Preparation prior to bonding with RITETITE CONTROL Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE CONTROL Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$54.39
Fast setting supa glue in a convenient bottle that allows easy, controlled and precise application. Features Easy, controlled application Non-drip glue saver nozzle, reduces waste and mess. Long fine nozzle for precise application Bonds a variety of surfaces Extremely fast setting Dries Clear for clean, neat results Water resistant No clamping necessary No mixing required Maximum strength achieved in 12 hours Only takes 45 seconds to achieve initial bond Non-clog cap Forms a rigid bond Upright self-standing bottle Comfortable to hold Where can this product be used? Ideal for small repair jobs or when immediate results are required. Water resistant not water proof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene. Leather may become hardened or discoloured For interior use only Not suitable for repairing items that are in direct contact with hot liquids Will not permanently bond glass or materials containing alkaline elements. Has no gap filling properties therefore surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Bonds a variety of porous and non-porous surfaces Metals China Rubber Leather Some plastics Wood How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Hold bottle in an upright position. Pierce seal by attaching nozzle and cap and turning clockwise. Remove cap and squeeze gently to apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. (30 seconds). The product grabs within 5-30 seconds, depending on environmental conditions and substrates to be bonded. Allow 30 minutes for sufficient bond strength for practical use. Maximum bond strength reached after 12 hours. Handy tips Cyanoacrylate adhesives can create a white residue on the surface of a substrate if the area is not well ventilated. Clean the affected area with acetone to remove residue. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. Excellent when used with other adhesives, as the temporary tack For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. Acetone (nail polish remover) or Olive oil can also be used to remove Quick Fix from skin. While superglue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Super glues cure more slowly when large amounts are used. For faster cure use sparingly. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Reseal cap in a clockwise direction. Tap bottle lightly on a flat surface to clear excess product from nozzle. To remove excess from substrates, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using thias method. Ensure cap is replaced and store in a cool dry place. Cyanoacrylate based adhesives polymerise in the presence of moisture. Store Upright. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$7.69
Single Shot, no mess just throw away Self piercing tube Bonds in 10 seconds Where can this product be used? Ideal for small repair jobs or when immediate results are required For interior projects and repairs Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or materials containing alkaline elements Has no gap filling properties, therefore, surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Metals China Rubber Leather Some plastics
$7.28
PC-SuperEpoxy® is a non-drip translucent paste epoxy suitable for conventional or static mixing. It has unlimited uses in bonding, assembling, filling and sealing most materials. Unlike conventional liquid epoxies, PC-SuperEpoxy® can be applied via a static mix nozzle vertically and overhead. It cures quickly at room temperature to form a resilient, non-conductive bond or seal that resists most chemicals, fresh and saltwater, gasoline and fuel oil. Works great bonding steel to wood, fibreglass, aluminium, concrete, brick, glass, block, ceramics, hard plastics and much more. PC-SuperEpoxy® is the toughest, highest strength epoxy we manufacture. WORK TIME: 15 MINUTES AND TACK-FREE IN 60 MINUTES CURE TIME: 4 HOURS (12 – 24 HOURS FOR FULL CURE) Here is a product that can take on the most challenging of projects with ease. Adhesion strength in excess of 2500 psi (up to 4000 psi). PC-SuperEpoxy® is a gel with a consistency like Vaseline. Here are just a few specific uses (there are hundreds of other uses): Anchoring or securing railings to wood or fibreglass decking. Seal cracks and holes in decking. Attach chocks, cleats, handles and pulls. Anchor or secure iron balusters to step and handrail. Fill cracked wood beam. Fix broken latch in the car glove box. Attach axe head.
$16.12
Imagine a liquid epoxy that is clear – A liquid epoxy with strength rivalling that of heavy duty paste epoxies – A liquid epoxy that has flexibility and is shatter resistant – A work time of 4 minutes and 1 hour cure time. Imagine NO LONGER! PC-Clear ™ Epoxy is a medium viscosity liquid epoxy system with greater clarity than other epoxies. This product is excellent for repairs and projects that must be less visible such as art objects or collectibles. PC-Clear™ epoxy is fast curing but allows ample time to apply and position the repair. After curing the epoxy does not become brittle, instead cured PC- Clear™ forms a tough resilient bond. PC-Clear™ can be used on more than just cosmetically critical repairs and in addition, it can be used for automotive, construction and facility repairs. Use PC-Clear™ when you are concerned about the appearance of your repair and a liquid epoxy is what you are looking for. Work time is about 4 minutes and cures in 1 hour. Here are just a few specific uses (there are hundreds of other uses): Fasten galvanized steel to a concrete floor. Bond sheet metal to wood or masonry. Seal and insulate electrical connections and electronic boards. Protect electronic components from vibration and moisture. Repair porcelain or sculptures. Reattach multiple broken pieces in a vase. How to prepare a surface for bonding with PC-Clear™ Epoxy Remove contaminants such as dust, dirt, oil and grime with a solvent such as Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good for removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-Clear™ Epoxy application Clean up mixed epoxy before it cures with paper towels and solvent. Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be removed with paint stripper or remover. FAQ Is PC-Clear™ Epoxy different from other clear epoxies? Some epoxies claim to be clear but they have a strong yellow tint that develops after it cures. PC-Clear™ Epoxy has a very slight hint of yellow that does not increase after curing. How does PC-Clear™ Epoxy’s strength compare to other epoxies? PC-Clear Epoxy™ is a strong adhesive with Lap Shear Adhesion strength on steel of 2500 psi. Is PC-Clear™ Epoxy brittle? PC-Clear™ Epoxy is slightly flexible and more resilient than other liquid epoxies. How does outdoor exposure affect cured PC-Clear™? Ultraviolet light will cause cured PC-Clear’s™ appearance to change and may cause yellowing. What is the best way to mix PC-Clear™? How you mix PC-Clear™ Epoxy will affect the length of working time. Flat surface mixing spreads the epoxy over an area minimizing the exotherm’s effect on the curing reaction and maximizing the length of work life. Mixing in a container concentrates the exotherm contributing to an increased rate of reaction and decreasing the work life. Why does PC-Clear™ Epoxy have a strong odor? The epoxy resin is nearly odorless. The hardener is the smelly part. It has an odor described as smelling like sewer gas or hair treatments. This odor comes from the polymercaptan but goes away upon curing. Does PC-Clear™ Epoxy self-level? PC-Clear Epoxy™ is a liquid and is self-levelling. How many feet of does the PC-Superepoxy® 50 ml cartridge nozzle dispense? PC-Superepoxy® can dispense approximately 20 feet of 1/8 inch bead. Can PC-Clear™ Epoxy be colored or tinted? PC-Clear™ Epoxy can be tinted.
$14.34
Parfix super glue is a fast setting cyanoacrylate-based adhesive that dries clear with a strong bond Instant strong bond Sets in 10 seconds Dries clear
$2.59
A rapid dual-action adhesive system is specially designed to work on plastic to form resilient, invisible bonds in seconds. Recommended on: Plastic, Porcelain, Metal, Rubber, Leather, Wood, Paper. Properties: Bonds even difficult to bond plastics such as polyethylene (PE) and polypropylene (PP) Bonds in seconds Dries transparent Easy to open, self-piercing and anti-clog cap Suitable for use on most surfaces* Solvent-free * Except Styropor®, car glass and synthetic fibres. Use: Ensure surfaces to be joined are clean, completely dry and close fitting. Using the Surface Activator like a pen apply it to both surfaces and wait 60 seconds to dry. Twist the glue cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$10.67
Loctite Epoxy Instant Mix 5 Minute is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 5 minutes and reaches handling strength in 1 hour. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. Loctite Epoxy Instant Mix 5 Minute does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on: Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fibreglass, concrete and stone Can be combined with fibreglass cloth for a durable patch Great for crafting projects Properties Will not crack when drilled Can be tinted to match surrounding materials Water resistant: can be used outdoors Does not shrink One-time application Convenient instant mix syringe Consistently dispenses equal, uniformly mixed amounts of each component Sets in 5 minutes Quick completion of the project How to Use: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from the centre of the plunger. Turn nozzle end up and pull the plunger back slightly allowing air bubbles to rise to the top. Snap off and discard end of the syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto the surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$9.23
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. Features: CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More Directions All surfaces must be clean and tight fitting. Clear Gorilla Glue will stain clothes. 1. Damp It For non-porous surfaces only (i.e. metal, glass, plastics), lightly dampen one surface with water. Do not add water to the bottle. 2. Glue It Apply Clear Gorilla Glue to surfaces. Best at room temperature. 3. Clamp-It Clamp objects together for 2 hours. Full cure in 24 hrs. You can use heavy objects to achieve clamping pressure. *Not recommended for use on polyethylene or polypropylene plastics. Storage Tips After each use, wipe nozzle clean with a dry cloth and tightly replace lid. Store in a cool, dry place with exposure to light. Lack of light and heat can cause the product to yellow. Cured glue can be removed from work surface with chisel, scraper or sandpaper. Store away from children and animals. Specs: APPLICATION TEMPERATURE – 32° to 100° F, best at room temperature SERVICE TEMPERATURE – -20° to 180° F OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – No FAQS What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight-fitting joints. It’s perfect for a fix you need doing fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also gap filling which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant and can withstand intermittent exposures, however, is not meant for a constant soak. Original or White Gorilla Glue is 100% waterproof and can withstand soaking and longer-term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$22.51
APPLICATION 1. Pierce seal at end of tube by turning nozzle and cap clockwise. 2. Ensure the working surface is clean, dry, free of dust or any grease. 3. Apply adhesive sparingly to one surface only. 4. Place surfaces together and press firmly for 10 - 60 seconds. Adequate for practical purposes after 30 minutes STORAGE: 5. After use. clean nozzle immediately with a cloth, replace cap and store upright between 5- 25°C. Avoid strong light and heat sources LIMITATION: Not recommended for polyethylene, polyester plastic & glass. Not suitable for use on items which contain hot liquids eg. Cups, mugs. May cause leather to discolour or harden. Test on a hidden area before use if in doubt. For interior use only.
$1.99
APPLICATION 1. Pierce seal at end of tube by turning nozzle and cap clockwise. 2. Ensure the working surface is clean, dry, free of dust or any grease. 3. Apply adhesive sparingly to one surface only. 4. Place surfaces together and press firmly for 10 - 60 seconds. Adequate for practical purposes after 30 minutes STORAGE: 5. After use. clean nozzle immediately with a cloth, replace cap and store upright between 5- 25°C. Avoid strong light and heat sources LIMITATION: Not recommended for polyethylene, polyester plastic & glass. Not suitable for use on items which contain hot liquids eg. Cups, mugs. May cause leather to discolour or harden. Test on a hidden area before use if in doubt. For interior use only.
$1.50
Overview Tired of unreliable glues that fall apart? Meet our game-changing Epoxy Adhesive, a powerhouse in bonding technology. In just a single 25mL package, this epoxy adhesive promises unparalleled durability and convenience. It dispenses effortlessly, ensuring a precise ratio for maximum strength. With a fast-acting formula that's perfect for bonding a variety of materials, your DIY or repair projects just became hassle-free! Features Automatic Self-Mixing Nozzle No more guesswork! Our self-mixing nozzle automatically dispenses epoxy and hardener in the exact ratio for optimal performance. Fast Setting & Long-Lasting Sets in just 5 minutes. Can be safely handled within 30 minutes. Attains full strength after 16 hours. Versatile Usage Ideal for bonding ceramics, glass, leather, wood, plastic, and metal. Your go-to solution for a myriad of projects. Superior Formulation 50% Epoxy Resin 50% Modified Amine Produces a high-strength bond resistant to temperature fluctuations between -40°C and 80°C. How to Use Preparation Safety First: Always wear protective gloves and safety glasses. Surface Preparation: Ensure the surface is clean, dry, and free from dust, oil, and grease. Application Air Removal: Hold the dispenser, nozzle end up, for 30 seconds to release entrapped air. Cut the tip carefully. Dispensing: Press the plunger slowly to dispense equal parts of resin and hardener. Mixing: Mix thoroughly before applying. Bonding: Apply adhesive to the surface and hold until set. Use tape or clamps if necessary. Post-Application Cleanup: Use acetone for cleaning. Storage: Store in a cool, dry place with the nozzle end up.
$9.95
For very narrow or no grout line applications - Syringe is not pre-filled.
$18.00
A strong and durable, fast setting two part epoxy adhesive that dries crystal clear making it ideal for areas where an invisible bond is required. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Weather and yellowing resistant. Shock resistant. Features: -Araldite is stronger than other glues due to the chemical reaction of the two parts. -Bonds a variety of surfaces -Dries Crystal Clear so there’s no visible evidence of repair -Quick setting in 5 minutes -No clamping necessary -High water resistance -Forms a rigid, durable bond -Can be used for gap filling (Surfaces need not mate closely) -Good chemical resistance -Heat Resistant -Doesn’t yellow over time so is ideal for use on glassware Appearance: Crystal Clear Where can this product be used? -Fixing a broken glass vase -Repairing jewellery -Toy repairs -Fixing ornaments or crockery -Fixing your handbag strap -Not suitable for bonding plastics such as Polypropylene and Polyethylene or for use on polystyrene What materials is this product suitable for? -Glass -Metal -Wood -Fabric -Rigid Plastic -Crystal -Leather How to use this product: -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each -Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow the bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. -When using tube kit, ensure correct caps are replaced on each tube or they will adhere. Handy tips: -A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol). -Clamping is recommended for a stronger bond. -For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. -To extend product life replace caps immediately after use. -When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) -Wipe off any uncured Araldite with acetone or nail polish remover. -To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. -To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. -Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. -Keep a box of Selleys Sugar Soap Wipes around for quick & effective cleanup -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Safety tips: -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Do not use solvents near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. -Non-toxic when set. Storage and re-use: Ensure caps or lids are replaced and product stored in a cool dry place.
$20.22
A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$25.07
A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength after 3 days. Features: -Araldite is stronger than other glues due to the chemical reaction of the two parts -Bonds a variety of surfaces -Dries Clear -Very Strong, durable bonding -Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) -Forms a rigid, durable bond -Can be used for gap filling (surfaces need not mate closely) -Good chemical resistance -Heat Resistant -Clamping is recommended to achieve a stronger bond -Not suitable for bonding plastics such as Polypropylene and Polyethylene -Bond strength weakens above 80°C but strength is regained when temperature drops Appearance: Translucent Where can this product be used? -Load bearing repairs -Gluing the head back on your hammer -Fixing loose table or chair legs. -Bonding solid pieces of Aluminium sheeting -Bonding timber on your boat -Repairing splits and cracks in Cricket bats -Bonding fibreglass sheets -Repairing Ski’s -Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? -Glass -Metal -Wood -Fabric -Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics -Crystal -Leather How to use this product -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each -Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. Handy tips -For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. -To extend product life replace caps immediately after use. Ensure you wipe excess from the nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. -When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) -Wipe off any uncured Araldite with acetone or nail polish remover. -To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. -To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. -Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. -Clamping recommended for a stronger bond. -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. -Ensure the surface is dry before applying the product. Safety tips: -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Do not use solvents near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention -Non-toxic when set. -For further information refer to the Material Safety Data Sheet (MSDS). -Storage and re-use -Ensure caps are replaced and product stored in a cool dry place.
$20.05
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very quick setting in 90 seconds No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling Good chemical resistance Where can this product be used? General small household repairs Fixing gemstones to mounts Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Most Plastics How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately. Ensure correct caps are replaced on each tube or they will adhere. Handy tips Note: For information on how to identify plastics refer to the Selleys plastics guide. For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured Araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep a couple at home just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$17.84
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance: Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product: General Use -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$9.58
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance: Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product: General Use -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$14.20
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$19.37
Adhesives and repair systems for cracked housings, toys, trims and more. See options for general plastics plus harder‑to‑bond PP/PT where indicated. Prep is key, clean thoroughly and follow cure times. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
