![Timbermate Woodfiller putty crack filler Interior 2Kg [Jarrah]](http://gluesaustralia.com.au/cdn/shop/files/9315284002000.jpg?v=1754811488&width=645)
Timbermate Wood filler is an Interior grade 4 in 1 Wood Putty, Grain Filler, Edge Filler and Crack Filler. When thinned slightly with water can also be used as a sanding sealer. Timbermate does not shrink, sink, crack or fall out and has an indefinite shelf life. It is non-flammable, non-toxic and can be used to the last gram. The secret ingredient of Timbermate is tap water, therefore, containing no Acrylic, Latex or Solvents. Timbermate comes in 13 premixed colours plus Natural Tint Base. Timbermate takes all types of known stains, varnishes and coatings. The Timbermate formula is over 85 years old and is the only genuine water-based formula in the world proving that the formulation has stood the test of time. Features & Benefits of Timbermate No Waste, Usable to the last drop. If tub dries out just add water to soften. Won't Shrink, Sink, Crack or Fall Out. Suitable for use in all Timbers including Particle Board M.D.F. (Custom Wood) *Plaster Board, Flooring, Panelling etc. Can be used as Wood Putty, Sanding Sealer, Prime Coat, Grainfiller, Crackfiller, Undercoat & Edge Filler all in one. Available in 13 Timber Tones plus Natural. Use White for top coats only. Can be tinted in wet state or overstained when dry. Use any type of Colorant i.e. Water Based Spirit based ochers etc. Easy sanding, will not clog paper when DRY Sanded dust can be mixed with water for re-use. Fast drying approx. 20-30 min, but can be heat dried with a heat gun or lamp for faster drying. Temperature can affect drying time. Clean hands or tools with water. Non-Flammable, Non-Toxic, Non-Yellowing. Solvent, Latex and Acrylic Free. Heat Proof and Freezeproof. Provides a strong foundation for all top coats inc. Single & two pack products polyurethane's, oils, acrylics, french polish wax etc. Takes nails, screws, planing, sawing, drilling and routing Can be used on Metal, Plastic, Fibreglass and in Foundries. 100% Australian Made and Owned. Available in pack sizes of 250g, 500g, 2Kg, 8Kg, 20Kg and 200Kg. Interior Grade. Edgefiller Apply TIMBERMATE with a spatula or knife using hand pressure to force into the Edge or End of the grain. For spray gun use stir 10%-15% water into TIMBERMATE fit a 2mm mozzle and set pressure to 60psi. Boards can be stacked for easy spraying. Allow to dry and sand with a fine grit paper and apply topcoat. Woodfiller/Wood Putty Fills cracks, knots, pin and screw holes, splits, blemishes, etc. Fill deep holes in layers allowing time for each layer to dry. Will not blind natural wood grain. Drying time is about 30 minutes. TIMBERMATE dries hard and smooth without shrinking or sinking and can be belt or drum sanded as it is not affected by heat, the hotter it gets the harder and faster it sets and that means less "Down Time." You can speed dry TIMBERMATE by adjusting the surrounding air temperature. This can be done by using either hot air, heat lamps, or kiln ovens.TIMBERMATE can be mixed with any stains before or after the filler is dry. To match medium and darker shades mix with Natural, Pine or other light shades. Use white TIMBERMATE only for white top coats. Grainfiller Mix 10% to 15% water into TIMBERMATE to make a perfect Grainfiller, Sanding Sealer and Prime Coat all in one application. First sand surface and with fine grit sandpaper, then apply Grainfiller to surface with a spray gun, paint roller, hessian or a cloth rolled into a ball, rub across the grain in a circular motion finishing with the grain. Sand, once filler is dry, to perfection with either sandpaper or power sander, using a fine grit paper. Grain filer can be used in a Roller or Curtain Coater or Spray Gun using a 2mm nozzle and 60psi pressure. Can be further thinned down with water if required. MDF Due to the finishing system used to manufacture MDF, it is essential to seal the job with a water-based non-acrylic product before applying top coats. Therefore TIMBERMATE meets your needs. Flooring Preparing old floors: Scrape all dust and waste between boards and surface as well as from knot holes and nail heads, vacuum well and carry out first sanding to prepare for filling and coating. Ensure that floor is stabilised, dry and free of movement. Application new floors and prepared old floors: Fill cracks, knot and nail holes and all blemished with a putty knife. Fill deeper holes in layers of about 6mm allowing each fill to dry. Apply TIMBERMATE to the entire floor, as a sealant, using a squeegee, trowel or paint roller. Allow to dry and sand off with a fine paper - 120 to 150 grit is recommended for best results. The floor can now be stained or varnished. Frequently Asked Questions Question: Is TIMBERMATE toxic, flammable or harmful? Answer: It is advisable to carry out safe work practices, as you would when working with dust. (Use an approved dust mask and safety goggles). TIMBERMATE contains no harmful ingredients and is non-flammable. Question: Can TIMBERMATE be used externally? Answer: No, as TIMBERMATE® is resoluble in water it is not advisable to use it outdoors. TIMBERMATE IS RECOMMENDED FOR INTERIOR USE. For external use, we recommend Earls MulTFill, Powder Putty or Porion Flexible Filler. Question: Can TIMBERMATE be used with stains and other finishes? Answer: Yes, TIMBERMATE® will take all types of known stains, coatings and colourants which can be Water based, Oil based, Solvent or Spirit based and even Acid Catalysed Lacquers. Question: Can TIMBERMATE be grainfilled? Answer: Yes, TIMBERMATE is a non-solvent based filler and is ideal for grainfilling. Mix 10-15% hot water to thin the Timbermate, then rub over the grain or spread thinly (see below for more detailed instructions). TIMBERMATE will: *Not raise the grain *Not damage the grain TIMBERMATE is: *Easy to sand when dry *Easy to stain when dry *Heat proof so you can speed the drying time by heating with a hair dryer, heat gun, lights etc. Question: How is the grainfiller applied? Answer: Take some TIMBERMATE out of the tub and place it in a separate container. Add approximately 10-15% water, (1gm=1ml) and mix into a slurry like paste (like toothpaste). Use a LINT FREE CLOTH AND RUB ACROSS THE GRAIN. When grainfiller goes "whitish" and sands off easily like talc powder, it is dry. TIMBERMATE will not blind the sandpaper (ie. clog up). If sandpaper gets clogged the grainfiller is not dry. Sand off in the same direction as the grain. Stain or coat when dry. Question: When is the stain applied? Answer: You can stain before or after applying TIMBERMATE (see "How do I match colours"). Question: How are the colours matched? Answer: Colour matching is easy. You can do it either of the following ways: Add your colourant to the putty and match the exact colour whilst wet. TIMBERMATE will dry lighter, but coat back to its original wet colour once coated with clear finishes. The final result is what you see (wet) is what you get. You can stain TIMBERMATE once it is dry. To test if dry, just rub sandpaper over putty. If putty clogs the sandpaper the filler is still wet. Wait for TIMBERMATE to dry and then stain. Question: How long does TIMBERMATE take to dry? Answer: Depending on the weather and depth of fill, TIMBERMATE will dry as follows: In hot weather, TIMBERMATE dries quicker. In cold weather, the depth of fill will determine the drying time. You can speed up the drying time by using a heat gun, hair dryer or light. Question: What depth or width can be filled? Answer: Do not fill holes deeper than 6-8mm at a time. TIMBERMATE dries quicker when filled in layers. Allow TIMBERMATE to dry between layers. Question: Why is the tub hard some days and feels dry and soft on other days? Answer: TIMBERMATE is waterbased. It contains no harmful solvents or acrylics and is, therefore, temperature sensitive. The warmer the weather or environment the softer the putty. On hot days it will start to dry in the tub if not properly sealed. Add a few drops of water to re moisten. Question: How is TIMBERMATE softened? Answer: Add a few drops of warm water to the top of the tub. It will soften quite quickly. If tub is frozen, thaw out by standing tub in a tub of hot water or place in a microwave for 20 seconds. TIMBERMATE is freeze thaw stable. Question: Can TIMBERMATE be used for any other purpose other than wood repair? Answer: TIMBERMATE does not shrink, sink, crack or fallout and can, therefore, be used on Plasterboard, Masonry, Fibreglass, Plastic and any other surface. Bearing in mind that steel must be coated with a primer to avoid rusting. Question: Can TIMBERMATE go off or does it have a shelf life? Answer: TIMBERMATE has an unlimited shelf life and will last indefinitely. If contents become dry merely add a few drops of water to reconstitute. DO NOT add more water than is necessary or leave excess water in the tub for a long period of time. The trapped excess water in the tub will cause the putty to become contaminated and will start to degenerate. Question: Why are so many colours available? Answer: We manufacture 13 colours to match almost all shades and types of timber. If you are using a clear coat you must match your putty colour. If staining, use Natural (tinting base). Question: What is Tint Base (Natural) putty and why? Answer: Tint Base (Natural putty) is putty in its natural state uncoloured. You may add the lightest shade of tint to change its colour. Question: Can TIMBERMATE be used on floors? Answer: TIMBERMATE is ideal for filling cracks, gaps, and nail holes in floors. TIMBERMATE will enhance the grain on the floor. As it does not shrink, sink, crack or fall out it is highly recommended for all floors. Question: Can TIMBERMATE be used with French Polish and Waxes? Answer: You can use all types of Waxes, Shellac and Oils on TIMBERMATE. Question: How is an incorrect match or badly filled hole fixed? Answer: Errors can be fixed with ease. If TIMBERMATE is not coated then wash out. If already coated, then break the top coat and then wash out. Refill or rematch if necessary. Question: Is TIMBERMATE Australian owned and manufactured? Answer: Yes. TIMBERMATE is 100% Australian owned and manufactured. An all Australian dedicated workforce does all manufacturing in our Melbourne factory.
$0.00 - $89.00
Earl’s MulTfill is a premium, ready-to-use multi-purpose filler designed for fast, clean, and durable repairs across interior and exterior projects. The heavy-bodied formula spreads smoothly, levels cleanly, and dries hard without shrinking, sinking, cracking, or falling out. With zero VOCs and no acrylics, latex, or solvents, it’s a low-odour choice for homes, workshops, and job sites. Clean-up is simple with water, and once dry MulTfill sands easily to a fine, paint-ready surface. Why you’ll love it Ready from the tub: no mixing, no mess, no wastage — just open, apply, and close. Zero VOCs: stable, low odour and user-friendly. Non-sinking, non-shrinking: fills stay flush and true. Won’t fall out: dries hard for lasting repairs. Paintable finish: accepts most coatings for a seamless result. Sands like a dream: refined finish without clogging when sanded dry. Long shelf life: keep the lid sealed and it’s ready when you are. Where it works Use MulTfill on common building materials including wood (including weathered and damaged sections once sound), masonry, plasterboard, cement sheet, concrete, and primed metal. It’s ideal for nail holes, dents, shallow voids, corner repairs, skim touch-ups, and general surface preparation before painting. Colour options White, Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut. How to use Prep: Ensure the area is clean, dry, and sound. Remove loose material and dust. For best glide, lightly wet your putty knife. Apply: Press firmly to fill the defect and smooth off. For deep voids, apply in layers up to 6 mm per pass, allowing each layer to dry before the next. Sand: Once fully dry, sand with 120 grit or finer to achieve a smooth, level surface. Coat: Prime if required, then paint. For clear finishes, tint the filler with suitable colorants or oxides before application to harmonise with surrounding material. Cleanup & care: Clean tools with water. If product thickens in the tub, add a few drops of clean water and stir until smooth. Always reseal promptly. Pro tips Feather edges wide when blending across boards or wall patches. On exterior jobs, protect from rain during cure and overcoat appropriately for exposure. Tinting before clear coats helps the repair visually disappear on timber substrates. Specifications Brand Earl’s Product Type Multi-purpose paintable putty / filler (water-based) Use Interior and exterior VOC Zero VOC Contains No acrylic, latex, or solvents Substrates Wood, masonry, plasterboard, cement sheet, concrete, primed metal Application Thickness Up to 6 mm per layer; allow to dry between layers Sanding Dry sand; 120 grit or finer Overcoating Accepts most paints; for clear coats, tint filler first for best colour match Clean-up Water Colours White; Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut Pack Sizes 140 g, 600 g, 1 kg, 2 kg, 3 kg (varies by colour) Shelf Life Up to 5 years if sealed and stored correctly Country of Origin Australia Storage Keep container tightly closed when not in use. Store in a cool, dry place out of direct sun. Avoid prolonged freezing. If product thickens, add a few drops of water and mix to restore spreadability. What’s in the tub A smooth-spreading, heavy-bodied filler that levels cleanly, sands easily, and delivers a paint-ready finish across interior and exterior surfaces — with no mixing, no fuss, and no strong odour.
$6.00 - $52.00
Agnews Water Putty - Hard-Setting Filler for Wood, Plasterboard, Concrete & More Agnews Water Putty is a professional, powder-based repair and levelling compound for durable, long-lasting results. Mix only what you need with clean water, then patch, level or rebuild surfaces with confidence. Once cured, it sets rock hard, bonds permanently, and can be sawn, drilled and sanded to a smooth, paint-ready finish. Key features Brand: Agnews Unlimited shelf life when stored dry Non cracking, non shrinking, non sinking Won't fall out – adheres firmly and fills to any depth Interior & exterior grade (seal exterior applications after full dry) Non flammable and no VOCs Mix what you need for minimal waste Suitable substrates Plasterboard, concrete, wood/timber, cement sheet, masonry. Also suitable for minor floor levelling and feathering on concrete, timber and ceramic tile substrates. Typical applications Fill holes in wood: knotholes, nail and screw holes, dents, edge build-ups Wall patching: cracks and cavities in plasterboard and cement sheet Furniture repair: tighten loose joints, reset fasteners, rebuild profiles Floor levelling: ramp or smooth minor level variations before floor coverings Trim and fixtures: refit loose door bumpers and trims with reliable hold Architectural & hobby moulding: casting and shaping durable components Why choose Agnews Agnews Water Putty cures to a dense, stone-hard finish that resists shrinkage and cracking even in deep fills. It bonds securely, stays put, and finishes cleanly, delivering a stable base for sanding, priming and painting. From small touch-ups to larger restorations, it provides consistent, professional results. Directions (general guide) Surface prep: Ensure the area is clean, dry, sound and free of dust, oil or loose material. For very porous substrates, lightly dampen to reduce rapid suction. Mix: Add powder to clean water and blend to a smooth, lump-free paste. Adjust water to suit application (thicker for filling, looser for fairing/skim). Apply: Press firmly into cracks or voids with a putty knife or trowel. Overfill slightly so you can sand back flush. Cure: Allow to dry thoroughly. Dry time varies with thickness, temperature and humidity. Finish: Sand to profile. Prime and paint or seal. For exterior applications, always seal after full dry. Exterior use guidance This is a hard-setting, non-flexible compound. For exterior use, only apply over stable substrates with minimal expansion and contraction from temperature changes. Ensure the putty is fully dry before sealing with a suitable exterior-grade coating. Finishing & compatibility Paintable and sealable after full dry; prime as required for best results. Can be cut, carved, drilled and sanded after cure without crumbling. For stained timber finishes, test a small area first for colour and absorption. Pro tips Mix small batches and use promptly. For deep voids, apply in layers if needed, allowing each layer to firm before the next. Store powder in a cool, dry place to maintain its unlimited shelf life. Clean tools with water before material cures. At a glance Substrates: plasterboard, concrete, wood/timber, cement sheet, masonry Uses: patching, levelling, rebuilding, moulding Properties: non cracking, non shrinking, non sinking, non flammable, no VOCs Finish: hard, dense, smooth and paint-ready after sanding/priming
$7.00 - $40.00
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.98
![Selleys Marine Flex For Boats Pools and Spas Water Proof [White]](http://gluesaustralia.com.au/cdn/shop/files/091876a6025d44ea89c711822b3ea3d8.jpg?v=1757752868&width=645)
Selleys Marine Flex is a high-performance adhesive and sealant designed for marine and water-exposed applications. Using Sil-X advanced polymer technology, it provides a permanent watertight seal above and below the waterline, even in salt, fresh, or chlorinated water. Key Features Cures and bonds underwater No primer required for most surfaces Strong and flexible bond absorbs vibration and movement Solvent-free and isocyanate-free formulation Sandable once cured 10-year watertight seal guarantee (above waterline) Where to Use Ideal for marine, pool, spa, and construction projects where water exposure or movement is expected. Suitable for bonding and sealing: Boat hulls, fittings, and deck seams Pool tiles, coping, and skimmer boxes Concrete, fibreglass, sealed timber, and metal surfaces Glass, ceramics, and most rigid plastics Technical Details Technology Sil-X advanced polymer Colour White or Black Size 410g cartridge Finish Smooth, paintable once cured How to Apply Ensure surfaces are clean and free from grease, oil, or dust. Can be applied to damp or wet surfaces. Cut the nozzle to the desired bead size and apply using a standard caulking gun. Tool the sealant immediately with a soapy water solution before it begins to skin. Allow to cure fully before sanding or painting if required. Limitations Not suitable for polyethylene (PE), polypropylene (PP), or PTFE materials Gelcoat surfaces should be lightly sanded before application The watertight guarantee applies to applications above the waterline Why Choose Selleys Marine Flex When you need a sealant that can withstand constant water exposure, movement, and vibration, Selleys Marine Flex delivers unmatched reliability. It bonds powerfully, stays flexible, and ensures a lasting waterproof finish for marine, pool, or construction applications.
$26.75
Selleys All Clear Crystal: The Ultimate Multipurpose Sealant Key Features Works on wet, oily, and dirty surfaces Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Best For Metal, Timber, Glass, Glazed tiles, Brick, Stone, and many plastics (may damage polystyrene and polycarbonate). Applications Sky lights Window frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' entries Shower screens Sinks and basins Caravans and recreational vehicles How to Use Use only in a well-ventilated area. Ensure surface is clean and dry. Apply with a caulking gun and smooth with a tool dipped in turps. Limitations May damage some plastics Not for permanent water immersion Not suitable for use over silicones or polystyrene foam Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by cutting and scraping. Technology & Cure Time Solvent-based, with a full cure time of 48-72 hours. For both interior and exterior use.
$16.00
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$11.52
BostiBostik Glu Stik is a clear, mess free adhesive designed for quick everyday sticking at home, school, and the office. It glides on smoothly, dries clear, and is perfect for paper projects that need a clean finish without wrinkling. Why you will love it Dries clear for a neat finish Solvent free and non toxic Low mess, easy to control twist up stick Washable from most fabrics Photo safe and acid free Ideal size for pencil cases, craft kits, and desk drawers Best for Paper and cardboard Scrapbooks, school projects, craft, and gift wrapping Office tasks like mounting notes and labels How to use Ensure surfaces are clean, dry, and free of dust. Twist the base to expose a small amount of glue. Apply a thin, even layer to one surface and press parts together. Adjust positioning within a short open time, then hold or smooth down to bond. Good to know Not suitable for heavy or structural bonding. For best results on photos or coloured paper, apply lightly to prevent over wetting. Replace cap after use to prevent drying out. Clean up and safety Fresh residue wipes away with a damp cloth. Wash from most fabrics in a standard warm wash. Non toxic, however supervision is recommended for young children. Specifications Brand Bostik Product Glu Stik Clear Glue Stick Size 8 g Color when dry Clear Solvent content Solvent free pH and acid content Acid free, photo safe Primary materials Paper, cardboard Clean up Water wipe while wet, machine washable from most fabrics Frequently asked questions Can I use it on photos? Yes. The formula is acid free and photo safe, making it suitable for photo mounting and scrapbooking. Does it dry clear? Yes. It applies smoothly and dries clear for a tidy finish. What materials does it bond? It is designed for porous, lightweight materials such as paper and cardboard. It is not intended for plastics, metal, glass, or heavy items. What is in the pack 1 x Bostik Glu Stik Clear Glue Stick 8g
$2.20
Dunlop Ready-to-Go Coloured Grout is a premium, pre-mixed grout for fast, clean results on walls and floors. No mixing, no mess, just open, apply, and buff for a smooth, long-lasting finish. The formula includes Grout Shield for anti-mould and anti-bacterial protection to help surfaces stay cleaner for longer. Suitable for interior and exterior applications, and available in a wide colour range to match or contrast your tiles. Ready-mixed convenience, apply straight from the tub Contains Grout Shield for mould and bacteria resistance Use on walls & floors, indoors & outdoors* Ideal for joint widths from 1–5 mm Great for rejuvenating old grout (min. removal depth: 1 mm walls, 2 mm floors) *Always follow the data sheet guidance for your specific area and exposure. Where to Use Ceramic, porcelain and most glazed tiles Bathrooms, kitchens, splashbacks, laundries, living areas Light-duty exterior tiled areas (check exposure & substrate) This grout is designed for typical domestic and light commercial tiling where a smooth, uniform finish is desired. Colours & Finish Available in a contemporary colour palette (e.g. whites and greys) to complement most tile styles. Use Dunlop’s colour selector to visualise combinations before you start. Coverage Coverage varies by tile size, joint width and depth. As a guide (per kg) of grout: Tile size (L×W×Thickness) Joint width 1.5 mm Joint width 3 mm Joint width 5 mm 25×25×4 mm mosaics ≈1.04 m²/kg ≈0.52 m²/kg ≈0.31 m²/kg 100×100×8 mm ≈2.08 m²/kg ≈1.04 m²/kg ≈0.63 m²/kg 200×200×8 mm ≈4.17 m²/kg ≈2.08 m²/kg ≈1.25 m²/kg Tip: Allow an extra 10–15% for wastage due to technique, tile type and site conditions. Directions (Summary) Prep: Ensure joints are clean, dry, and free from dust, adhesive residue and contaminants. For rejuvenation, remove at least 1 mm (walls) or 2 mm (floors) of old grout. Apply: Using a rubber grout float, force grout firmly into joints at a 45° angle. Strike & shape: Allow grout to firm in the joint (~15 mins). Shape joints as required. Clean: Wipe diagonally with a dense, damp sponge, rinsing frequently. Use minimal water to reduce shade variation and shrinkage. Buff: When touch-dry (typically 6–24 hrs), buff tile faces with a clean, dry cloth. Drying & Use Initial set at ~24 hrs at 23 °C / 50% RH Shower walls can be exposed to water after ~24 hrs Clean-Up & Storage Clean tools and residue with water while the grout is still wet. Reseal the tub between uses to prevent skinning. Store upright in a cool, dry place. Safety Read the Safety Data Sheet before use and follow PPE guidance. Avoid contact with eyes and prolonged skin contact. Keep out of reach of children.
$16.30 $0.02/g
Glue Dots Flexible Hang Tabs Brand: GlueDots Make decorating effortless and worry free. Glue Dots Flexible Hang Tabs give you a fast, clean and removable way to hang balloons, banners, streamers, paper lanterns, lightweight garlands, bunting, ornaments and more. The crystal clear tabs apply in seconds, hold firmly to most smooth household and event surfaces, and remove cleanly when the party is over. Damage free: removes cleanly from most properly painted, sealed and smooth surfaces when used as directed. Instant bond: pressure sensitive adhesive grips on contact for quick setup. Crystal clear: low visual impact for a neat, professional look in photos and in person. Flexible design: engineered slot holds standard latex balloons without helium, plus tabs act as anchor points for string, ribbon or fine wire. No tools, no mess: no nails, pins, tacks or putty required. Indoor friendly: ideal for homes, venues, classrooms, offices and display windows. Why choose Flexible Hang Tabs From last minute birthday setups to polished corporate events, these tabs are your decorating shortcut. The flexible slot lets you slide in a balloon neck or thread ribbon, while the clear base keeps the focus on your décor. When it is time to pack down, the removable adhesive lets you lift and peel without gouging walls or leaving sticky residue. Versatile surfaces: painted walls, sealed plaster, varnished timber, tile, glass, metal, laminate and most smooth plastics. Looks better: clear tabs virtually disappear against most backgrounds. Saves time: decorate large areas quickly with repeatable placement. Reliable hold: grips evenly across the tab to help prevent droop. Great for Balloon walls and garlands without helium Banners, bunting and streamers across hallways or backdrops Paper lanterns, pom poms and lightweight ornaments from ceilings Classroom displays and noticeboards where pins are not allowed Retail window dressing and temporary point-of-sale displays Wedding, engagement, baby shower and seasonal décor How to use Prepare the surface: ensure it is clean, dry, smooth and free of dust, oils and cleaning sprays. Fresh paint should be fully cured. Peel and place: remove a tab from the liner, align and press firmly for several seconds to ensure full contact. Hang décor: slide a balloon neck into the slot or thread ribbon, cord or lightweight line through the tab opening. Adjust if needed: for best results, reposition immediately after placement before full bond develops. Removal and clean up To remove, gently lift a corner of the tab and peel it back slowly over itself at a low angle. If resistance is felt, pause and continue slowly. On delicate finishes, test in an inconspicuous area first. Dispose of tabs with household waste. No solvents or scraping required when used as directed. Pro tips Use multiple tabs to distribute weight across wider banners or garlands. Avoid textured, dusty, damp or porous surfaces which reduce adhesion. For ceiling applications, ensure the surface is smooth and dust free. Allow items that were stored cold to reach room temperature before use. Indoor use recommended. Prolonged exposure to moisture, heat or direct sunlight may reduce performance. Safety and care Keep out of reach of small children. Not a toy. Do not use to hang valuable, fragile or irreplaceable items. Always test on a small area of the surface if uncertain. Specifications Brand GlueDots Product name Flexible Hang Tabs Colour Clear Adhesive type Pressure sensitive, removable Finish Crystal clear, low profile Recommended use Indoor, temporary decorating and light display mounting Suitable surfaces Painted and sealed walls, sealed plaster, varnished wood, tile, glass, metal, laminate, most smooth plastics Unsuitable surfaces Textured, dusty, damp, porous, unsealed or flaking finishes Residue on removal Removes cleanly when used as directed on suitable surfaces Repositionable Yes, during initial placement Operating conditions Room temperature, dry environment Applications Balloons, streamers, banners, paper lanterns, pom poms, lightweight ornaments Tools required None Country of use Suitable for Australian homes, venues and classrooms Performance can vary with substrate, surface preparation and environmental conditions. Always follow the directions and test before full application. What you get Flexible, clear hang tabs on an easy peel liner. Pack quantities vary by selection. Choose the pack size that suits your event or display plan. Storage Store in a cool, dry place away from dust and direct sunlight. Keep in original packaging until use to protect adhesive surfaces. Plan your next event From birthdays to window displays, build cleaner backdrops and crisper lines with Glue Dots Flexible Hang Tabs. Add to cart and get decorating in minutes.
$13.00
One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces 100% crystal clear / transparent Good workability Very good adhesion on many typical building materials Use: Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including: Plasterboard Wood surfaces Painted enamel Polyester Plastic Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions. CHARACTERISTICS AND ADVANTAGES 100% crystal clear / transparent Good workability Low shrinkage during cure Flexible and elastic Can be used on damp concrete Very good adhesion on many typical building materials COLOUR: Transparent Product Data Appearance / Colours Transparent Packaging 300 g cartridge (290 ml), 12 cartridges per box Storage Conditions / Shelf-Life Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met. Technical Data Chemical Base Silane terminated polymer Density 1.05 kg/l approx. (ISO 1183-1) Tensile Strength 2.0 N/mm2 approx. (ISO 37) Shore A Hardness 30 approx. (after 28 days) (ISO 868) Elongation at Break 400% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Service Temperature −40 °C to +70 °C SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department. Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly. Bonding After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again. Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear. Sealing After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.
$23.63
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$22.98
Loctite Epoxy Instant Mix 5 Minute is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 5 minutes and reaches handling strength in 1 hour. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. Loctite Epoxy Instant Mix 5 Minute does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on: Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fibreglass, concrete and stone Can be combined with fibreglass cloth for a durable patch Great for crafting projects Properties Will not crack when drilled Can be tinted to match surrounding materials Water resistant: can be used outdoors Does not shrink One-time application Convenient instant mix syringe Consistently dispenses equal, uniformly mixed amounts of each component Sets in 5 minutes Quick completion of the project How to Use: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from the centre of the plunger. Turn nozzle end up and pull the plunger back slightly allowing air bubbles to rise to the top. Snap off and discard end of the syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto the surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$9.23
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.90
Give everyday cleaning a simple, natural boost with Glitz Bi-Carb Cleaner. This all purpose powder uses the gentle abrasive action and deodorising properties of sodium bicarbonate to lift grime, cut through kitchen film, and freshen household surfaces without added fragrances or dyes. Why you will love it Versatile cleaner for kitchens, bathrooms, laundry, and outdoor touch ups Deodorises fridges, bins, shoes, and pet areas Gentle abrasive action helps remove tea stains, soap scum, and cooked on residue Eco minded choice with a simple, trusted mineral based formula Food area friendly when used as directed, then rinsed well Value size 1kg pack is ideal for regular household cleaning Where to use Benchtops, sinks, stovetops, splashbacks Microwaves, fridges, lunch boxes, drinkware Showers, tiles, grout, basins Bins, pet bowls, outdoor furniture Laundry pre soak for odours in sportswear and towels Car interiors and coolers How to use General cleaning: Sprinkle a small amount onto a damp cloth or sponge. Wipe the surface, then rinse and dry. Stubborn marks: Make a paste with a little water. Apply to the stain, leave for 5 to 10 minutes, then scrub lightly and rinse. Deodorising: Sprinkle directly onto the source of odour, leave for 15 minutes, then vacuum or rinse away. Drains and sinks: Add half a cup followed by hot water to help freshen and reduce build up. Good to know Non scratch on most hard surfaces when used with a soft cloth No added fragrance or dyes Septic safe when used as directed Ingredients Sodium Bicarbonate. Care and safety Test on an inconspicuous area first, especially on delicate finishes and natural stone. Do not use on aluminium, lacquered or highly polished surfaces. Avoid contact with eyes. Keep out of reach of children and pets. Store tightly closed in a cool, dry place. Pack information Brand Glitz Product Bi-Carb Cleaner Natural Eco All Purpose Powder Net weight 1kg Format Fine cleaning powder Country of use Australia Simple tips Refresh chopping boards by applying a paste, scrubbing lightly, then rinsing with warm water. Neutralise fridge odours by placing an open dish in the fridge and replacing monthly. Lift tea and coffee stains in mugs by soaking with a warm water paste for 20 minutes before washing. What customers ask Is it safe on stainless steelYes, use a soft cloth, rub with the grain, then rinse and dry. Can it be used on natural stoneTest first. Rinse thoroughly and dry to protect sealed finishes.
$12.40 $10.11
Glitz Citrus Dishwashing Liquid Fresh Lemon Clean 5L Make light work of dishes with a refreshing lemon clean. Glitz Citrus Dishwashing Liquid delivers rich suds that lift grease and food residues fast, leaving plates, glasses, and cookware spotless with a fresh citrus finish. The generous 5L bulk pack is ideal for busy family homes, offices, cafes, and community kitchens that want reliable performance and great value. Why you will love it Powerful everyday clean that breaks down oils and baked on residues Fresh lemon fragrance for a just cleaned scent Stable foam for longer sink time and fewer top ups Rinses easily to help reduce spotting and streaks Cost effective 5L format for regular high volume washing Versatile for hand washing dishes, cutlery, glassware, and cookware Best for Daily sink loads at home or in shared kitchens Cafes, lunchrooms, clubs, and community events Rental properties and short stay turnovers How to use Fill sink with warm water. Add dishwashing liquid. Start with 1 to 2 teaspoons per 5L of water for light to normal soils. Increase for heavy grease. Wash using a sponge or brush. Soak stubborn items for a few minutes. Rinse thoroughly with clean water and allow to air dry or towel dry. Tips For glassware, use hot water and a soft sponge to help prevent water spots. Change solution when suds begin to collapse or water appears cloudy. Do not use in automatic dishwashers. This formula is for manual washing. Product details Brand Glitz Product Citrus Dishwashing Liquid Fragrance Fresh Lemon Format Liquid Size 5L Use Manual dishwashing and general sink cleaning Suitable surfaces Dishes, cutlery, glassware, ceramics, stainless steel cookware Country of use Australia What is in the box 1 x Glitz Citrus Dishwashing Liquid Fresh Lemon Clean 5L Storage and safety Store upright in a cool, dry place away from direct sunlight. Keep out of reach of children and pets. Avoid contact with eyes. If product gets in eyes rinse with water. If irritation occurs discontinue use. Sustainability note Use the recommended dose to minimise waste and water use. Recycle the container where local facilities allow. Frequently asked Can I use it on non stick cookware Yes, use a soft sponge and follow the cookware care instructions. Is it safe for septic systems This hand dishwashing liquid is designed for general household use. As with any cleaner, use as directed and follow local guidance for septic systems.
$25.86 $20.56
Glitz Citrus Dishwashing Liquid Fresh Lemon Clean 2L, Make light work of dishes with a refreshing lemon clean. Glitz Citrus Dishwashing Liquid delivers rich suds that lift grease and food residues fast, leaving plates, glasses, and cookware spotless with a fresh citrus finish. The generous 2L, bulk pack is ideal for busy family homes, offices, cafes, and community kitchens that want reliable performance and great value. Why you will love it Powerful everyday clean that breaks down oils and baked on residues Fresh lemon fragrance for a just cleaned scent Stable foam for longer sink time and fewer top ups Rinses easily to help reduce spotting and streaks Cost effective 2L, format for regular high volume washing Versatile for hand washing dishes, cutlery, glassware, and cookware Best for Daily sink loads at home or in shared kitchens Cafes, lunchrooms, clubs, and community events Rental properties and short stay turnovers How to use Fill sink with warm water. Add dishwashing liquid. Start with 1 to 2 teaspoons per 2L, of water for light to normal soils. Increase for heavy grease. Wash using a sponge or brush. Soak stubborn items for a few minutes. Rinse thoroughly with clean water and allow to air dry or towel dry. Tips For glassware, use hot water and a soft sponge to help prevent water spots. Change solution when suds begin to collapse or water appears cloudy. Do not use in automatic dishwashers. This formula is for manual washing. Product details Brand Glitz Product Citrus Dishwashing Liquid Fragrance Fresh Lemon Format Liquid Size 2L, Use Manual dishwashing and general sink cleaning Suitable surfaces Dishes, cutlery, glassware, ceramics, stainless steel cookware Country of use Australia What is in the box 1 x Glitz Citrus Dishwashing Liquid Fresh Lemon Clean 2L, Storage and safety Store upright in a cool, dry place away from direct sunlight. Keep out of reach of children and pets. Avoid contact with eyes. If product gets in eyes rinse with water. If irritation occurs discontinue use. Sustainability note Use the recommended dose to minimise waste and water use. Recycle the container where local facilities allow. Frequently asked Can I use it on non stick cookware Yes, use a soft sponge and follow the cookware care instructions. Is it safe for septic systems This hand dishwashing liquid is designed for general household use. As with any cleaner, use as directed and follow local guidance for septic systems.
$13.69 $10.99
Glitz Degreaser Heavy Duty Kitchen Cleaner 500ml Cut through baked-on grease and everyday kitchen grime fast. Glitz Degreaser Heavy Duty Kitchen Cleaner is a ready to use spray designed for cooktops, rangehoods, splashbacks, benches, and more. It lifts fats, oils, and food residue so you get a clean, streak free finish with less scrubbing. Why you will love it Heavy duty action - breaks down stubborn grease, oils, and burnt on residue Ready to use - no mixing required, just spray, wait, and wipe Streak free finish - leaves hard kitchen surfaces looking fresh Versatile - ideal for stainless steel rangehood exteriors, ceramic and glass cooktops, tiled splashbacks, benches, cupboard doors, and BBQ exteriors Fast results - reduces scrubbing time on tough build up Best for these jobs Cutting grease on cooktops and around burners De gunking rangehood filters and exteriors Cleaning oven doors and surrounding panels Removing oily fingerprints on cupboard doors and fridges Wiping down tiled splashbacks and benchtops Directions Switch off appliances and allow surfaces to cool. Shake bottle gently. Turn nozzle to spray. Spray directly onto the soiled area from 15 to 20 cm. Allow 2 to 3 minutes contact time on heavy build up. Do not let dry on the surface. Wipe with a damp cloth or non scratch sponge. Rinse food contact surfaces with clean water and dry with a lint free cloth. Good to know Always test on an inconspicuous area first. Not recommended for unsealed or porous stone such as marble and limestone, unsealed timber, raw aluminium, brass, copper, or varnished surfaces. For painted surfaces, dilute on a cloth first and test. Do not use on hot surfaces. Avoid prolonged contact with stainless steel. Rinse and dry after cleaning. Do not mix with other cleaners or chemicals. Specifications Brand Glitz Product type Heavy duty kitchen degreaser Format Ready to use spray Size 500 ml Suitable surfaces Stainless steel exteriors, ceramic and glass cooktops, tiles, laminates, enamel, sealed stone, and most non porous hard surfaces Safety Wear gloves if you have sensitive skin. Use in a well ventilated area. Avoid breathing spray. Keep out of reach of children and pets. If product gets in eyes rinse with water for several minutes. If irritation persists seek medical advice. Frequently asked questions Can I use this on a hot plate or warm oven No. Always allow surfaces to cool before cleaning. Is it safe on food contact areas Yes, but after cleaning you must rinse the surface with clean water and dry. Will it remove baked on carbon inside an oven It helps on light to moderate build up. For heavy carbon you may need a dedicated oven cleaner. What is in the box 1 x Glitz Degreaser Heavy Duty Kitchen Cleaner 500ml spray bottle Glues Australia ships fast Australia wide. Questions about surface compatibility or bulk orders Contact our team and we will help you choose the right cleaner for the job.
$7.93 $6.33
Glitz Cleaning Vinegar Natural Eco Multi Purpose Cleaner 2L Make everyday cleaning simple with this powerful plant based vinegar cleaner. It cuts through grease, soap scum, water marks and light mineral deposits while leaving hard surfaces streak free. Ideal for kitchens, bathrooms, windows and floors, all in one generous 2L value pack. Why you will love it Natural cleaning power that tackles grime without harsh chlorine or ammonia. Streak free finish on glass, stainless steel and glossy tiles. Deodorises bins, laundry and pet areas with a fresh, clean scent. Concentrated value that you can use neat for tough spots or dilute for everyday mopping. Family friendly fragrance free formula suitable for regular cleaning. Eco mindful choice in a recyclable bottle. Where to use Kitchen benches, splashbacks and sinks Cooktops and stainless steel appliances Showers, taps, tiles and grout Windows, mirrors and glass doors Floors including sealed vinyl, sealed timber and tiles Laundry deodorising and general wipe downs Not recommended on Natural stone such as marble, limestone, travertine or unsealed granite. Avoid use on waxed or oiled timber, unfinished metals, electronics and any surface that is not water safe. Always spot test in a hidden area first. How to use General spray and wipe: Add to a trigger bottle. Light soils 1 part vinegar to 3 parts water. Spray, wipe clean, then dry with a lint free cloth. Glass and mirrors: Dilute 1 part vinegar to 4 parts water. Spray lightly and polish dry. Bathrooms: Use neat on soap scum and tapware. Apply, leave 2 to 3 minutes, scrub if needed and rinse well. Dry metal surfaces after rinsing. Floors: Add 1 cup to a 5L bucket of warm water. Mop and allow to air dry. Deodorise: Lightly mist bins or laundry tubs, then rinse or wipe after a few minutes. Tips for best results Do not mix with bleach or products containing bleach. Rinse natural rubber and metals after contact. Use microfiber cloths for a streak free finish. Product details Brand Glitz Product Cleaning Vinegar Natural Eco Multi Purpose Cleaner Size 2L Format Ready to use or dilute as directed Fragrance Fragrance free with mild vinegar scent Surface compatibility Glass, stainless steel, ceramic, enamel, chrome, sealed tiles, sealed timber, vinyl Bottle HDPE recyclable Safety Keep out of reach of children and pets. Avoid contact with eyes and prolonged skin contact. If in eyes, rinse with water. Do not ingest. Do not mix with other chemicals. Store upright in a cool, dry place with cap closed. Frequently asked questions Can I use it on stone benchtops? No. Acids can etch natural stone. Use a stone safe neutral cleaner for marble, limestone, travertine or unsealed granite. Is it safe for stainless steel? Yes for quick wipe downs. Spray onto a cloth, wipe, then buff dry. Always rinse and dry taps and fittings. Can I use it in a steam mop? Check the appliance instructions. If additives are not recommended, use the floor dilution in a regular bucket and mop instead. What is included 1 x Glitz Cleaning Vinegar Natural Eco Multi Purpose Cleaner 2L Shipping and pickup Fast dispatch Australia wide from our Melbourne warehouse. Click and Collect available on request. Contact us to arrange a pickup time.
$3.89 $3.29
Keep your surfaces clean with PREP Hospital Grade Lemon Disinfectant. This concentrated, hospital grade formula destroys germs fast and is ideal for general purpose cleaning at home, in offices, and in workplaces. Hospital grade disinfectant with fresh lemon fragrance Concentrated formula for effective sanitising and everyday cleaning Suitable for kitchens, bathrooms, floors, walls, and high touch points Economical, easy to dilute, and simple to use How to Use For hospital grade disinfecting: Dilute 1 part concentrate with 3 parts water (1:3). Apply to pre-cleaned hard, non-porous surfaces. Allow adequate contact time, then rinse if required. For light cleaning: Dilute 250 mL concentrate in 2.5 L water (approximately 1:10). Mop, wipe, or spray, then allow to dry. Rinse food contact surfaces with potable water after use. Where to Use Benchtops, sinks, taps, splashbacks Floors, walls, tiles, grout Toilets, bathrooms, showers Desks, door handles, handrails, shared touch points Good to Know Concentrate makes multiple ready to use bottles from one pack Lemon scent leaves areas smelling fresh after cleaning Versatile for both sanitising and routine maintenance cleans Dilution Guide Application Ratio Example Mix Hospital grade disinfecting 1:3 (concentrate:water) 250 mL + 750 mL water Light cleaning 1:10 (approx.) 250 mL + 2.5 L water Safety Use on hard, non-porous surfaces only Wear gloves for prolonged use and ensure good ventilation Avoid contact with eyes and skin. Do not ingest Keep out of reach of children and pets Specifications Brand Prep Productions Product Type Hospital grade disinfectant concentrate Size 1 Litre Fragrance Lemon Item Weight 1.2 kg Package Dimensions 19 cm x 13 cm x 7 cm Always follow label directions. Test on a small inconspicuous area before first use.
$12.50
Selleys Liquid Nails Direct Stick Liquid Nails Direct Stick is a high strength polyurethane flooring adhesive designed for timber strip flooring and parquetry. Its semi rigid formula delivers a strong bond that helps reduce cupping and rafting. A controlled foaming action fills minor gaps. Fast cure means most floors can be sanded the next day to keep your project moving. Key Features High strength bond for timber flooring Semi rigid formula to help reduce cupping and rafting Foaming action fills small gaps and irregularities Fast cure so you can sand the next day Easy application with a strip flooring or parquetry trowel Where It Works Timber strip flooring Parquetry installations Interior floors on suitable, dry substrates Technical Details Technology Polyurethane adhesive Cure time Overnight under normal conditions. Sand and finish the next day. Application temperature 10°C to 30°C Coverage 2 m² per 1 L using the correct trowel 20 m² per 10 L using the correct trowel Clean up Protect adjacent finishes. Wipe fresh adhesive from surfaces before cure. Important Information Apply with a strip flooring or parquetry trowel to achieve stated coverage. Floors can usually be sanded the next day after proper cure. Protect surrounding finishes from expansion during foaming. Limitations Not suitable for wet or damp substrates. Avoid application below 10°C. Directions for Use Prepare the surface. Ensure substrates are clean, dry, sound, and free from dust, oil, and contaminants. Apply adhesive. Use the correct strip flooring or parquetry trowel. Spread adhesive evenly within the working time. Lay flooring. Place boards or parquetry into the wet adhesive. Press firmly to ensure full contact and adhesive transfer. Allow to cure. Leave to cure overnight under recommended conditions. Finish. Sand and finish the floor as required once the adhesive has cured. Good to Know Semi rigid bond helps manage seasonal timber movement. Foaming action assists with minor surface irregularities and gap filling. For best results, follow timber flooring manufacturer guidelines and site preparation standards. Available sizes: typically 1 L and 10 L tubs. Check current availability on this page before ordering.
$13.34
Boyle Gloss All in One Glue Sealer and Finish 236 ml Seal, glue and finish your craft projects with a single water based formula that dries clear and glossy. Boyle Gloss All in One is ideal for decoupage, paper craft, school projects and home decor. It brushes on smoothly, holds strongly and leaves a protective shine. Key benefits Three in one formula for gluing, sealing and top coating Gloss finish that dries clear and enhances colours Water based and low odour for indoor use Brushes on easily and levels well Great for beginners and experienced makers Best for Decoupage and collage Paper, card and photos Wood, MDF and craft boards Canvas and fabric accents Lightweight embellishments and mixed media Surface compatibility Use on clean, dry and dust free surfaces. Test on a small area first, especially on delicate papers, prints or dyed fabrics. How to use Prepare: Ensure the surface is clean and smooth. Cut and position your paper or embellishments. Glue: Apply a thin even coat to the surface with a soft brush. Press the item in place and smooth out any bubbles. Seal: After the glue layer sets to tack free, brush a light coat over the top. Allow to dry fully. Finish: Add 1 to 3 additional thin coats for a stronger, glossier finish. Lightly sand between coats if a super smooth result is desired. Dry time and coverage Touch dry in about 15 to 30 minutes depending on coat thickness and conditions Recoat after 30 to 60 minutes Allow 24 hours before light handling. Full cure develops over several days Coverage varies with technique. Thin coats give the best clarity and bond Clean up Wash brushes and tools with warm soapy water while wet Wipe any fresh drips with a damp cloth Tips for a glossy result Apply multiple thin coats rather than one heavy coat Work in one direction for the first coat, then cross coat for the second Use a soft synthetic brush or foam applicator to minimise brush marks Important information For indoor craft use Keep out of reach of children Avoid freezing. Store upright with the cap closed tightly Specifications Type: All in one glue, sealer and finish Finish: Gloss clear Base: Water based Size: 236 ml
$11.00
The Buzz Indoor Pest Glue Traps 4 Pack Keep your home clean and comfortable with easy to use, non toxic glue traps that catch crawling pests fast. Each trap folds into a low profile tunnel that protects the sticky surface from dust and keeps pets and little hands away. No sprays, no odour, no mess. Key benefits Ready to use traps for ants, cockroaches, spiders, earwigs, silverfish and other crawling insects Pesticide free adhesive with long lasting tack Foldable tunnel design for discreet placement Works in kitchens, laundries, pantries, wardrobes, garages and under sinks Disposable after use to maintain hygiene What's included 4 x foldable indoor pest glue traps Where to place Along skirting boards and wall edges where insects travel Near rubbish bins, pet feeding areas and under appliances Inside cupboards, pantries and storage rooms Entry points such as doorways and around plumbing penetrations How to use Remove a trap from the pack and peel back the protective release paper to expose the glue surface. Fold along the marked lines to form a tunnel or leave flat if preferred. Place with the openings along walls or in corners. For best results use multiple traps in larger rooms. Check weekly. Replace when the surface is covered with dust or insects, or after 4 to 6 weeks. Pro tips Reduce competing food sources by wiping crumbs and storing food in sealed containers. Use additional traps near known pest hotspots for faster control. Combine with sealing of gaps and cracks for long term prevention. Disposal and safety To dispose, fold the trap closed so the adhesive is covered and place in household rubbish. Keep out of reach of children and pets. If glue contacts skin, remove with cooking oil then wash with soap and water. Good to know Indoor use only. Replace regularly for continuous monitoring and control. Scent free design suits food preparation and storage areas.
$7.32
![Bostik Blu Stik Glue Sticks 35g [10 Pack]](http://gluesaustralia.com.au/cdn/shop/files/3247a52b-3527-4297-825a-a050176be4e8_d6fe2015-9cbc-4930-b3d1-683224070b7d.png?v=1760577211&width=645)
Key features Goes on blue, dries clear for easy, mess free gluing Non toxic, acid free and solvent free Fast drying with a strong hold on porous materials Allows brief repositioning before it sets Twist up stick with tight sealing cap to prevent drying out Low mess and easy to use for kids and adults Great value multi pack for classrooms and home offices Ideal for Paper and cardboard Photos and craft paper Lightweight fabric embellishments School assignments, posters and scrapbooks Directions Surfaces should be clean, dry and free of dust. Uncap and twist the base to raise the glue. Apply a thin, even layer to one surface. Join parts and press firmly for several seconds. Allow to dry. Full strength is reached after the glue has set clear. Clean up and safety Wipe fresh residue with a damp cloth. Wash hands and tools with warm soapy water. Keep capped when not in use. Keep out of reach of young children. Good to know Not recommended for non porous surfaces like metal or glass. For best results, store in a cool, dry place. Pack contents 10 glue sticks x 35 g each.
$33.50
Bostik Green Stik is an easy to use glue stick for everyday crafting, school projects, and office tasks. It applies smoothly, goes on clear, and dries clear for a neat finish. Why you will love it Non toxic and acid free Smooth application with strong initial tack Ideal for paper crafting, cut and paste, and classroom use Low mess and easy to control for kids and adults Surfaces Paper Cardboard Light fabric and similar porous materials How to use Ensure surfaces are clean, dry, and free from dust. Twist the base to raise the glue. Apply a thin, even layer to one surface. Press surfaces together firmly for several seconds. Allow to dry. For best results on heavier paper, apply to both surfaces. Clean up Wipe away excess with a damp cloth while still wet. Allow to dry fully before handling. Environment and packaging Formulated with a high percentage of natural ingredients Packaged in a recycled plastic container with soy ink label Packaging is curbside recyclable in many areas when the lid is attached Good to know Colour when applied: clear Dries: clear Size: 35 g
$4.95
Bostik Pink Stik is a neat, no-mess glue stick that goes on pink so coverage is easy to see, and dries pink to add fun colour to your creations. Perfect for school projects, craft, scrapbooking and everyday office use. Why you will love it Goes on pink and dries pink Smooth application with quick grab Non toxic and acid free Low mess twist up tube Washable from hands and most fabrics Best for Paper, card and photos School assignments and scrapbooks Office presentations and collages How to use Ensure surfaces are clean, dry and free from dust. Twist up a small amount of glue and apply a thin, even coat to one surface. Join surfaces and press firmly. For heavier card, apply to both surfaces. Replace cap after use to prevent drying out. Clean up and safety Fresh glue washes off skin with soap and water. Wipe excess from surfaces with a damp cloth before it dries. Keep out of reach of young children when not in use. Specifications Brand Bostik Product Pink Stik Glue Stick Size 35 g Colour (wet) Pink Colour (dry) Pink Suitable materials Paper, card, photos, light fabrics Not recommended for glossy plastics, foam, or other non porous surfaces where a stronger adhesive is required.
$4.95
![Bostik Blu Tack Reusable Adhesive 75g [Pink]](http://gluesaustralia.com.au/cdn/shop/files/BOBLUTACGN_05.jpg?v=1760306853&width=645)
Why you will love it Reusable and repositionable No pins or tape required Low mess with easy clean up Holds posters, photos, notes, and lightweight items Malleable for custom shapes and small gap fixes Ideal uses Posters and signs on painted walls, tiles, glass, and metal Securing items on desks and shelves Keeping cables tidy and in place Crafts, school projects, and model making How to use Ensure surfaces are clean, dry, and free from dust or grease. Pinch off a small piece and knead until soft and warm. Form into a ball and place on the item to be mounted. Press firmly to create a good bond. Use more for heavier items. Removal tips Peel off slowly by rolling the adhesive away from the surface. If residue remains, dab with a fresh piece to lift it. Test on delicate or matte paints in an inconspicuous area first. Good to know Not suitable for highly absorbent, recently painted, or dusty surfaces. Avoid use on silk screens, flocked or delicate wallpapers, and porous finishes. Store in a cool place inside the pack for best performance. Specifications Type Reusable adhesive putty Colour Pink Pack size 75 g
$6.50
![Bostik Blu Tack Reusable Adhesive 75g [Yellow]](http://gluesaustralia.com.au/cdn/shop/files/BOBLUTACGN_06.jpg?v=1760306777&width=645)
Why you will love it Reusable and repositionable No pins or tape required Low mess with easy clean up Holds posters, photos, notes, and lightweight items Malleable for custom shapes and small gap fixes Ideal uses Posters and signs on painted walls, tiles, glass, and metal Securing items on desks and shelves Keeping cables tidy and in place Crafts, school projects, and model making How to use Ensure surfaces are clean, dry, and free from dust or grease. Pinch off a small piece and knead until soft and warm. Form into a ball and place on the item to be mounted. Press firmly to create a good bond. Use more for heavier items. Removal tips Peel off slowly by rolling the adhesive away from the surface. If residue remains, dab with a fresh piece to lift it. Test on delicate or matte paints in an inconspicuous area first. Good to know Not suitable for highly absorbent, recently painted, or dusty surfaces. Avoid use on silk screens, flocked or delicate wallpapers, and porous finishes. Store in a cool place inside the pack for best performance. Specifications Type Reusable adhesive putty Colour Yellow Pack size 75 g
$6.50
![Bostik Blu Tack Reusable Adhesive 75g [Green]](http://gluesaustralia.com.au/cdn/shop/files/BOBLUTACGN_03.jpg?v=1760306665&width=645)
Why you will love it Reusable and repositionable No pins or tape required Low mess with easy clean up Holds posters, photos, notes, and lightweight items Malleable for custom shapes and small gap fixes Ideal uses Posters and signs on painted walls, tiles, glass, and metal Securing items on desks and shelves Keeping cables tidy and in place Crafts, school projects, and model making How to use Ensure surfaces are clean, dry, and free from dust or grease. Pinch off a small piece and knead until soft and warm. Form into a ball and place on the item to be mounted. Press firmly to create a good bond. Use more for heavier items. Removal tips Peel off slowly by rolling the adhesive away from the surface. If residue remains, dab with a fresh piece to lift it. Test on delicate or matte paints in an inconspicuous area first. Good to know Not suitable for highly absorbent, recently painted, or dusty surfaces. Avoid use on silk screens, flocked or delicate wallpapers, and porous finishes. Store in a cool place inside the pack for best performance. Specifications Type Reusable adhesive putty Colour Green Pack size 75 g
$6.50
![Bostik Blu Tack Reusable Adhesive 75g [Orange]](http://gluesaustralia.com.au/cdn/shop/files/BOBLUTACGN_04.jpg?v=1760306533&width=645)
Why you will love it Reusable and repositionable No pins or tape required Low mess with easy clean up Holds posters, photos, notes, and lightweight items Malleable for custom shapes and small gap fixes Ideal uses Posters and signs on painted walls, tiles, glass, and metal Securing items on desks and shelves Keeping cables tidy and in place Crafts, school projects, and model making How to use Ensure surfaces are clean, dry, and free from dust or grease. Pinch off a small piece and knead until soft and warm. Form into a ball and place on the item to be mounted. Press firmly to create a good bond. Use more for heavier items. Removal tips Peel off slowly by rolling the adhesive away from the surface. If residue remains, dab with a fresh piece to lift it. Test on delicate or matte paints in an inconspicuous area first. Good to know Not suitable for highly absorbent, recently painted, or dusty surfaces. Avoid use on silk screens, flocked or delicate wallpapers, and porous finishes. Store in a cool place inside the pack for best performance. Specifications Type Reusable adhesive putty Colour Orange Pack size 75 g
$6.50
Make quick, mess free stick ups with Bostik Removable Glu Dots. These clear, pressure sensitive dots are perfect for posters, photos, cards, decorations and classroom or office displays. They bond instantly, then peel away cleanly from most non porous surfaces when it is time to change things up. Why you will love them Clear and discreet for a neat finish Instant grab with no drying time Removable from most non porous surfaces No liquid spills or smears Great for home, school, office and events Best for Mounting photos, posters and signage Craft projects and scrapbooking Party decorations and displays Temporary fixes on glass, metal, plastic and sealed wood How to use Ensure surfaces are clean, dry and free of dust or grease. Peel a dot from the liner and place it on the item to be mounted. Press firmly, then position the item and press again for a secure hold. To remove, slowly peel the item away. Roll any remaining dot off the surface with your thumb. Good to know Test on a small hidden area first, especially on delicate or recently painted surfaces. Not recommended on flocked or fibrous wallpapers, unfinished timber or porous paint. Heat, UV and surface condition can affect removability. Product details Brand Bostik Product Removable Glu Dots Colour Clear Pieces 64 dots Bond type Removable, pressure sensitive Clean up Peel off and roll away residue
$7.00
Key features Dries clear for a neat, invisible finish Non toxic and low odour Water based for easy clean up before curing Suitable for brush or nozzle application Paintable when dry Strong bond on porous surfaces Ideal for Paper, cardboard, photos, and scrapbooking Craft foam, felt, and fabric edge bonding Balsa wood and other light timbers School and hobby projects Directions Ensure surfaces are clean, dry, and free of dust or oil. Apply a thin, even coat to one surface. For very porous materials, coat both surfaces. Join pieces while the glue is wet and press firmly. Clamp or weight if needed. Wipe away excess with a damp cloth. Allow to set. Light handling is typically possible after 30 to 60 minutes. Full strength develops after 24 hours. Clean up Clean tools and fresh spills with a damp cloth. Once cured, scraping or sanding may be required. Handy tips For stronger joints on timber, lightly sand and dry fit pieces before gluing. Avoid excessive glue, which can lead to slow drying and warping on thin paper. Not suitable for continuous water immersion or load bearing joins. Storage Replace cap after use. Store upright in a cool, dry place away from frost and direct heat. Safety Non toxic formula. If irritation occurs, discontinue use. Technical details Base PVA emulsion Appearance White, dries clear Viscosity Medium, smooth flow Open time Up to 10 minutes depending on surface and coat weight Set time Approx. 30 to 60 minutes Full cure 24 hours Water resistance Not recommended for prolonged moisture exposure Paintable Yes, once fully dry
$11.30
Bostik Hobby Craft Dual Tip Liquid Glue 30ml is the perfect choice for creative projects, crafts, and schoolwork. Designed for precision and versatility, this liquid glue features two applicator tips, a fine tip for detailed work and a broad tip for larger surfaces. The smooth, clear formula ensures a clean, professional finish without clumping or streaks. Dual applicator design: Fine and broad tips for all craft needs Clear drying: Leaves no visible residue Ideal for: Paper, cardboard, photos, and light craft materials Easy to use: Non-toxic, washable, and child-friendly Perfect for school and home projects This handy 30ml bottle is compact and easy to store, making it a must-have for hobbyists, students, and anyone who loves crafting. Its dual-tip applicator provides control and convenience whether you're gluing delicate details or covering larger areas. Applications: Arts and crafts, card making, scrapbooking, paper modeling, and DIY projects. Brand: Bostik
$5.88
Bring colour to craft time with Bostik Glu Stik Rainbow. These smooth-gliding, non toxic glue sticks make school projects, scrapbooks, posters and office tasks quick and tidy. They go on smoothly, dry clear and are washable from hands and most fabrics, making them ideal for kids and classrooms. Key features Vibrant rainbow set for fun, easy-to-see application Non toxic and solvent free for peace of mind Dries clear for a neat, professional finish Low mess stick format with twist up design Washable from hands and most washable fabrics Acid free formula suitable for photos and paper crafts Best for Paper, cardboard and lightweight craft foams School homework, posters and collages Scrapbooking and photo mounting Office and home stationery tasks How to use Ensure surfaces are clean, dry and free of dust. Twist base to expose glue and apply a thin, even coat to one surface. Press surfaces together and smooth from the center outward. Allow to dry. For heavier paper, hold or weight for a stronger bond. Clean up Wipe away excess with a damp cloth while wet. Wash hands with warm soapy water. On washable fabrics, pre treat with stain remover and launder according to garment instructions. Helpful tips Replace cap firmly after use to prevent drying out. Use on porous, lightweight materials only. Not suitable for metal, glass or heavy plastics. Test on a small area of delicate papers or photos first. Specifications Format Glue sticks Pack size 5 sticks Stick weight 35 g each Colour Rainbow set. Dries clear Solvent Solvent free pH Acid free Safety: Keep out of reach of young children when not in use. Do not ingest. If irritation occurs, discontinue use.
$18.00
Key features Goes on blue, dries clear for easy, mess free gluing Non toxic, acid free and solvent free Fast drying with a strong hold on porous materials Allows brief repositioning before it sets Twist up stick with tight sealing cap to prevent drying out Low mess and easy to use for kids and adults Great value multi pack for classrooms and home offices Ideal for Paper and cardboard Photos and craft paper Lightweight fabric embellishments School assignments, posters and scrapbooks Directions Surfaces should be clean, dry and free of dust. Uncap and twist the base to raise the glue. Apply a thin, even layer to one surface. Join parts and press firmly for several seconds. Allow to dry. Full strength is reached after the glue has set clear. Clean up and safety Wipe fresh residue with a damp cloth. Wash hands and tools with warm soapy water. Keep capped when not in use. Keep out of reach of young children. Good to know Not recommended for non porous surfaces like metal or glass. For best results, store in a cool, dry place. Pack contents 5 glue sticks x 35 g each.
$23.00
Bostik Glu Tape is a clean, quick and mess free double sided adhesive for everyday sticking and craft projects. At 6 mm wide and 12 m long, it gives precise control for cards, scrapbooks, posters, school projects and office tasks. Why you will love it Instant stick with no drying time Clean finish with no liquid glue spills Thin 6 mm width for neat, accurate placement Strong hold on most paper and lightweight materials Great for home, school and office use Great for Card making and scrapbooking Mounting photos, prints and posters Sealing envelopes and gift wrapping School assignments and craft projects Suitable surfaces Paper and cardboard Lightweight foam and foamboard Most coated papers and photo papers How to use Ensure surfaces are clean, dry and free of dust or oils. Apply the tape along the area to be bonded, pressing down firmly. Peel away the release liner if present, then align and press surfaces together. Rub over the bond area to secure a strong hold. Tips Test on delicate or coated papers before full application. For best results, apply at room temperature and avoid stretching the tape. Store in a cool, dry place out of direct sunlight. Specifications Type: Double sided adhesive tape Width: 6 mm Length: 12 m Color: Clear adhesive Pack contents: 1 roll
$10.60
Key features Instant stick for quick, clean application Refill cartridge designed for the Bostik Glu Tape dispenser Neat roller action helps prevent lumps and smears Great for scrapbooking, school projects, cards, labels, and gift wrapping Transparent adhesive for a tidy finish Long length for multiple projects Best for Paper, card, photos, and lightweight craft materials Mounting, edging, and everyday office sticking jobs How to use Ensure surfaces are clean, dry, and free of dust. Open the dispenser, remove the empty cartridge, and click in the refill. Hold the roller at a slight angle and glide along the surface to apply adhesive. Press items together firmly for a secure hold. Good to know If you misplace a strip, gently lift before pressing down firmly. Store upright in a cool, dry place out of direct sunlight. Specifications Product type: Adhesive roller refill Length: 12 m Compatibility: Bostik Glu Tape dispenser Finish: Clear
$7.07
Keep your glue gun ready for any project with the Bostik HG3 Glue Gun Refills. These high quality hot melt sticks provide a smooth, even flow for clean and reliable bonding. Pack of 10 clear adhesive sticks Compatible with Bostik HG3 Glue Gun Creates a strong, flexible and transparent bond Suitable for wood, plastic, fabric, leather, ceramics and more Perfect for craft work, household repairs and DIY projects. The hot melt formula ensures quick adhesion with minimal mess, giving you professional results every time. How to use: Insert a glue stick into the back of your glue gun. Allow the gun to heat for a few minutes before use. Apply steady pressure on the trigger to release glue. Join surfaces immediately for best results. Let the glue cool completely before handling. Safety Information: Hot glue can cause burns. Avoid contact with skin and eyes. Keep out of reach of children. The Bostik HG3 Glue Gun Refills are ideal for quick fixes, decorative projects and reliable everyday bonding.
$15.21
Key benefits Goes on purple, dries clear for easy, accurate application Low mess, quick grab on paper and card Washable formula that cleans up with water Solvent free and non toxic, suitable for school use Twist up stick for smooth, even coverage Great value multi pack for home, school, and office Best for Paper and cardboard Photos and scrapbooking Homework and classroom crafts Gift wrapping and arts projects How to use Ensure surfaces are clean, dry, and free from dust. Twist the base to raise the stick a few millimetres. Apply an even coat to one surface using light pressure. Join within 30 seconds and press firmly along the bond line. Allow to dry. Handling strength is reached in minutes, full bond develops as it cures. Clean up and storage Fresh residue wipes away with a damp cloth. Wash hands and tools with water. Replace cap after use to prevent drying out. Store upright in a cool, dry place. Typical details Format Solid glue stick Colour when applied Colours Colour when dry Clear Set time Minutes, depending on coat weight and ambient conditions Clean up Water while wet Suitable materials Paper, card, photos, light crafts Not recommended for Non porous surfaces, heavy materials, or outdoor use Pack contents 4 x 8 g glue sticks
$7.77
Power Through Soap Scum & Kill 99.9% of Germs Selleys Complete Clean Bathroom & Shower Spray is a household-grade disinfectant cleaner that cuts through tough soap scum, dirt and grime while killing 99.9% of common bathroom germs (S. aureus and E. coli). Ideal for showers, bathtubs and toilets for a sparkling clean finish. Disinfects effectively: Kills 99.9% of germs (S. aureus & E. coli). Fast soap scum removal: Powers through built-up residue on bathroom surfaces. Household-grade disinfectant: Designed for hard, non-porous bathroom surfaces. Where to Use Suitable for hard, non-porous surfaces such as: showers, bathtubs, toilets and similar bathroom fixtures. Not Suitable For Marble, natural stone, porous tiles or aluminium surfaces Polished, varnished or lacquered surfaces Skin (hard surface disinfectant only) Directions Turn nozzle to ON while directing trigger away from face. Spray directly onto the surface until fully covered. For cleaning: wipe with a clean damp cloth or rinse. For disinfecting: allow 10 minutes contact time, then wipe with a clean damp cloth. On food-contact areas: rinse or wipe with a clean damp cloth after 10 minutes. Good to Know Always test on an inconspicuous area first. Avoid prolonged contact with sensitive surfaces listed above. Keep out of reach of children. Read label before use. Product Details Brand: Selleys Range: Complete Clean Type: Bathroom & shower disinfectant spray Size: 750mL trigger spray
$5.79
Earl’s MulTflex® Exterior Flexible Filler is a unique, single-pack, ready-to-use flexible filler and adhesive formulated for lasting repairs on timber and masonry. It delivers a durable, non-shrinking, non-sinking finish that won’t crack with vibration and won’t fall out, making it ideal for exterior maintenance where movement and weather can defeat ordinary fillers. Paintable when dry and formulated with no volatile organic compounds (No VOCs), it’s a dependable, low-odour solution for professional results at home or on site. Proudly 100% Australian made and owned. Why you’ll love it Exterior-grade flexibility: absorbs movement and vibration without cracking. Non-shrink & non-sink: holds profile and edge detail after cure. Won’t fall out: engineered adhesion for long-term durability. Ready to use: straight from the tub — no mixing, no mess, no waste. Paintable: achieves a seamless, colour-matched finish once dry. No VOCs: low odour, solvent-free formula. Interior / Exterior: versatile enough for both. Proudly Australian: made and owned in Australia. Where it works Use Earl’s MulTflex® to repair and rebuild on a wide range of common building substrates: Timber: decks, window frames, trims, fascia, general carpentry repairs. Masonry: brick, block, render and patching mortar-like defects. Plasterboard: exterior-exposed linings under cover and general patching. Metals & gutters: non-structural filling and profiling (clean, sound, free of rust). Around pipes & penetrations: neat, gap-free finishing before painting. Glass & surrounds: edge repairs and feathering prior to topcoating. Ideal projects Rebuilding weathered or rotten timber edges before repainting. Filling cracks and surface imperfections in rendered walls. Profiling and feathering joints and transitions for a paint-ready finish. General exterior maintenance where a flexible, paintable filler is essential. Directions Surface Preparation Remove loose or flaking material, dirt, dust, oil, grease and chalky paint. Substrates must be sound. Ensure surfaces are dry and free from visible moisture. Treat rust and stabilize friable areas as required. For best mechanical key, lightly abrade glossy surfaces and remove dust. Application Open the tub and use directly. If the surface of the product begins to dry, add a few drops of water and re-mix gently. Keep the container tightly sealed when not in use. Apply with a filling knife or trowel, pressing firmly to ensure full contact with the substrate. Build up in thin layers for deep repairs, allowing each layer to firm before adding the next. For a satin-smooth finish, tool the final pass with a wet knife or brush to reduce post-work finishing. Finishing & Painting Allow to dry fully. Dry time varies with film thickness, temperature and humidity. Once dry, apply a suitable primer/undercoat if required by your paint system, then topcoat. Use quality exterior paints for weather-exposed areas. Clean-Up & Storage Clean tools and splashes with water while wet. Reseal immediately after use to minimise skinning and reduce waste. Store upright with lid sealed. Do not allow contents to dry out. Good to know Formulation is unaffected by normal temperature swings and resists cracking with vibration. Designed for exterior flexibility yet also suitable for interior touch-ups. For best results on deep voids, fill in multiple light applications rather than one heavy pass. Specifications Brand Earl’s Product MulTflex® Exterior Flexible Filler Type Single-pack, ready-to-use flexible filler & adhesive Use Interior / Exterior Paintable Yes, once fully dry VOC Content No VOCs (as supplied) Shrink / Sink Non-shrinking, non-sinking Flexibility Resists cracking with vibration and movement Clean-Up Water (while wet) Substrates Timber, masonry, render, plasterboard, metals, gutters, around pipes, glass Finish Satin-smooth when tooled with a wet knife or brush Packaging Ready-to-use tub Country of Origin 100% Australian made & owned Limitations Do not apply to unsound, dusty or actively corroding surfaces without proper preparation. Dry and cure times depend on depth and conditions; confirm dryness before painting. Not intended for structural repairs. Pro Tips Feather edges wide for invisible paint blending on weathered timber and render. Keep a small cup of clean water nearby to maintain a smooth final pass. Deep cavities: bridge with successive thin layers for the most stable result.
$19.00 - $28.00
Earl’s Powder Putty – Mix-to-Use Interior & Exterior Filler Earl’s Powder Putty is a multi-purpose powder filler for professional and DIY repairs. Just add water, mix only what you need, and achieve a tough, easy-sand finish with no waste and no shrinking. Brand: Earl’s Interior and exterior use* Mix-on-demand convenience Non-shrinking, smooth finish Easy sanding and shaping Indefinite shelf life in dry powder form Proudly made in Australia *Exterior applications must be sealed/painted and used on stable substrates. About Earl’s Powder Putty Earl’s Powder Putty delivers reliable, high-quality filling for timber, walls, masonry and metal. Because it’s supplied as a dry powder, you can tailor the mix to your task—stiffer for knife-grade filling and sculpting, or looser for fine skim work. The result is a hardwearing repair that sands easily and accepts coatings beautifully. Where Earl’s Powder Putty Works Timber & woodwork: doors, frames, skirting, architraves, furniture, cabinetry Walls & panels: plasterboard and cement sheeting patching and feathering Masonry & concrete: chips, small holes and surface imperfections Metals: minor dents and irregularities prior to priming and painting Floor preparation: quick patching of distressed boards prior to covering Craft & hobby: architectural details, mouldings and small sculpting tasks Why Choose Earl’s No shrink: Formulated to dry without shrinking for flush, invisible repairs. Mix what you need: Reduce waste and always work with a fresh batch. Shapes perfectly: Once dry, Earl’s Powder Putty can be cut, carved, sanded or sawn. Paint-ready: Accepts primers and topcoats after proper dry and prep. Economical & dependable: Indefinite shelf life in powder form when stored dry. Directions for Earl’s Powder Putty Surface prep: Ensure the area is clean, dry and sound. Remove loose material, dust, grease and contaminants. Key glossy surfaces for better adhesion. Mix: In a clean container, add Earl’s Powder Putty and slowly incorporate clean water. Stir to a smooth, lump-free paste. Adjust water to suit the task. Apply: Press the mix firmly into the repair with a putty knife or trowel. Slightly overfill to allow for sanding back flush. Build: For deep repairs, apply in layers, allowing each to firm before adding the next. Finish: Once dry, sand smooth. The cured filler can be carved or sawn to refine edges and profiles. Coat: Prime/seal and paint after full dry. For exterior use, always seal with suitable coatings. Clean-up: Clean tools with water while the product is still wet. Dry and recoat times vary with temperature, humidity and film thickness. Allow extra time in cool or damp conditions and for deep fills. Good to Know About Earl’s Not waterproof by itself: Water and weather resistance requires sealing/painting. Not flexible: Avoid use where movement, vibration or structural flexing is expected. Stable substrates only: Ensure exterior bases are sound and well prepared. Storage: Keep Earl’s Powder Putty dry and tightly closed. Moisture exposure can reduce performance after opening. Safety: Avoid dust during mixing and sanding. Use PPE and adequate ventilation. Typical Earl’s Applications Filling nail and screw holes, chips and minor cracks Skim patching and feathering edges prior to painting Rebuilding small decorative profiles and mouldings Levelling minor surface imperfections before finishing Specifications Brand Earl’s Product Name Earl’s Powder Putty Product Type Multi-purpose powder filler Format Dry powder; mix with clean water Colour (dry) Off-white to white; paintable Use Areas Interior and exterior* (exterior must be sealed/painted; stable substrates only) Substrate Compatibility Wood, plasterboard, cement sheeting, concrete, masonry, properly prepared metal Shrinkage Non-shrinking when used as directed Sandability Easy sanding once fully dry Paintability Prime/seal and paint after full dry Water Resistance Requires sealing; product itself is not waterproof Shelf Life (powder) Indefinite when stored cool, dry and sealed Clean-up Water while wet Tools Putty knife, trowel, mixing stick or paddle, sanding block Country of Origin Australia Limitations of Earl’s Powder Putty Do not use as a flexible gap filler or where structural movement is expected. Always prime/seal before exposure to moisture or exterior weather. Deep repairs may require multiple layers with adequate drying between coats. Not for permanently wet, submerged or high-movement joints. FAQs – Earl’s Powder Putty Can I mix a large batch and store it?Mix only what you can use within the working time. Discard any mix that begins to stiffen or set. Can I screw or nail into it?For non-structural tasks, light fixings may be possible in sufficiently thick, fully cured areas. Pre-drill as needed and test first. Is it paintable?Yes. Once dry and sanded, prime or seal the repair and finish with your chosen coating system. Always follow label directions. Test on a small, inconspicuous area to confirm compatibility and finish.
$10.50 - $81.00
Bostik Ultra-Strong Clear Super Glue (Liquid, Odourless, Fast-Setting) Ultra-Strong Clear Super Glue is a professional-grade, medium-viscosity liquid adhesive designed for quick, reliable repairs on most non-porous materials. It forms an instant high-strength bond that sets in seconds and reaches full cure in 24 hours. The clear, solvent-free formulation is virtually odourless for a cleaner, more comfortable user experience, and its slightly flexible bond helps resist knocks and everyday drops once cured. Why You’ll Love It Fast setting: bonds in seconds to get you back to work quickly. Ultra strong: high strength once fully cured for durable, long-lasting repairs. Water & heat resistant: engineered to stand up to common household moisture and temperature swings. Odourless & solvent-free: cleaner application with a safer, low-irritation formula. Slightly flexible bond: helps absorb minor shocks and everyday handling. Ideal Materials Best results on clean, dry, non-porous surfaces including: China, ceramics and porcelain (non-permanent on items subject to frequent washing) Rubber and elastomers Metals and metal components Jewellery repair (non-food contact) Many rigid plastics* *Not suitable for polyethylene (PE), polypropylene (PP) or PTFE (Teflon®). Not recommended for permanently bonding glass, high-alkaline materials, or items that are regularly washed. Avoid paper and other highly porous substrates. Where It Excels Quick household fixes (knobs, clips, figurines, trim) Hobby & craft assembly (non-porous parts) Workshop touch-ups and small component repair Office and general repair kits How It Works This liquid cyanoacrylate reacts with trace moisture on surfaces to polymerise rapidly, forming a high-strength thermoplastic bond. The medium viscosity helps wet out tight-fitting parts while minimising run-off when applied sparingly. Before You Start Surface prep: Ensure both surfaces are clean, dry, and free from dust, oil, rust, release agents or old adhesive. Lightly abrade glossy plastics/metal where appropriate and wipe clean. Dry fit first: Check alignment, clamping and support so parts come together quickly and accurately. Protect work area: Use disposable backing and keep caps, tissues and a small amount of acetone or nail-polish remover handy for cleanup. Application (Liquid) Open: For first use, attach/screw the nozzle and remove the cap. Apply a tiny amount: Place a small drop on one surface only. More glue can slow cure and weaken the joint. Assemble: Bring parts together immediately and hold with firm, even pressure for ~20 seconds. Avoid movement during initial set. Let it cure: Handling strength develops quickly; allow 24 hours for full cure and maximum performance. Clean-Up & Rework Fresh squeeze-out: Wipe carefully. Small residues may be treated with acetone/nail-polish remover and gently scraped once softened. On skin: Do not pull apart. Soak in warm, soapy water and gently roll/peel. Use a blunt tool (e.g., spoon handle) to separate bonded skin slowly. Pro Tips for Best Results Use the smallest effective drop—thin bondlines are stronger. Maintain close-fitting joints; gaps reduce cure speed and strength. Avoid bonding on PE, PP, PTFE and materials with heavy plasticisers or strong alkalinity. Allow the full 24-hour cure before exposing to stress, moisture or heat. Storage & Shelf Life Store tightly closed in a cool, dry place below 25 °C, away from direct sunlight. Typical shelf life: 12 months from manufacture when stored as directed. Safety Cyanoacrylate adhesive: bonds skin and eyes in seconds. Keep out of reach of children. Wear protective gloves and eye protection. In eyes: rinse immediately with water and seek medical attention. Specifications Technology Modified Ethyl Cyanoacrylate (liquid, medium viscosity) Appearance / Colour Clear Typical Working / Set Time Up to ~20 seconds (conditions and substrates affect speed) Full Cure 24 hours Water & Heat Resistance Resistant after full cure (not for continual immersion or high-temperature structural loads) Odour / Solvents Virtually odourless; solvent-free formulation Bond Character Slightly flexible; resists minor knocks and drops when fully cured Suitable Substrates China, ceramics, rubber, metal, jewellery, many rigid plastics (non-porous, clean, dry) Not Recommended PE, PP, PTFE; permanent glass bonds; high-alkaline materials; frequently washed items; paper/very porous substrates Cleanup (Uncured) Acetone or nail-polish remover; scrape gently once softened Storage Cool, dry, below 25 °C; protect from sunlight Shelf Life 12 months from manufacture (stored as directed) FAQs Can I use it on flexible rubbers? Yes, many rubbers bond well; ensure surfaces are clean and oil-free. Is it dishwasher-safe? Not recommended for items that are regularly washed, soaked or immersed. Why shouldn’t I flood the joint? Excess adhesive slows cure and weakens the bond—thin layers perform best. Disposal Allow small residues to cure fully (exposed to air) before disposal in accordance with local regulations.
$7.89
Clear Flexible Fabric Glue A versatile, water-based fabric adhesive designed for clothing repairs, craft projects, and soft furnishings. It forms a strong, long-lasting, flexible bond on most porous fabrics and dries clear in thin films for a neat, professional finish. Once fully cured, the bond is machine washable, can be tumble dried, and is safe to iron. Key Features Permanent, flexible bond for clothing and crafts Water-based, low odour formula Dries clear in thin applications Machine washable and tumble-dry compatible after full cure Heat resistant—safe to iron over the bonded area Easy squeeze application; cleans up with warm soapy water while wet Ideal Uses Hems, trouser turn-ups, and pocket repairs Attaching cloth labels, badges, and patches Securing frayed lace ends and trims Curtain hems and decorative soft furnishing accents General fabric repairs on cotton, denim, linen, felt, leather and similar porous textiles Directions Preparation: Ensure surfaces are clean, dry, and free from dust or grease. At least one surface must be porous. Test first: Trial on an off-cut or hidden area, especially with light or open-weave fabrics. Apply: Spread a thin, even layer to the non-visible side or back of the fabric. Join parts and press for several seconds. Initial handling: Light handling is typically possible after about 1 minute; avoid stressing the bond. Optional set boost: For improved bonding, gently iron-press ~5 minutes after gluing (use a pressing cloth). Full cure: Reaches full effective strength after 24 hours. After curing, the item may be machine washed, tumble dried, and ironed. Clean-Up While wet: Wipe away with warm, soapy water; repeat if needed, rinse and dry. When dry on smooth, non-porous surfaces: Gently rub off or use warm, soapy water. When dry on fabrics: Difficult to remove—prevent excess and work carefully. Compatibility & Notes Best on porous textiles: cotton, denim, linen, felt, leather, and similar materials. Not suitable for non-porous materials or 100% nylon/polyester fabrics. Avoid heavy application or excessive pressure on light or open-weave fabrics to minimise show-through or darkening. Specifications Chemistry Acrylic copolymer (water-based) Appearance Milky white liquid; dries clear in thin films Density 1.07 ± 0.02 g/cm³ Solids Content 61–63% Viscosity Up to ~1,000 cps pH 4–6 Initial Handling Time ~1 minute (varies with material, temperature, humidity) Full Cure / Maximum Strength ~24 hours Washability & Heat Machine washable; tumble dry and iron once fully cured Clean-Up (Wet) Warm soapy water Pack Size 20 mL (blister) Storage Cool, dry place around 20 °C; keep container tightly closed; protect from moisture Shelf Life Up to 18 months from manufacturing date (unopened, stored as directed) Not Suitable For 100% nylon, 100% polyester, non-porous materials, very fine/delicate fabrics (e.g., some silks, wools, linens)
$13.98
Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications. Same formula & product you trust, just better looking! Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable. Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age. It is non-toxic, non-flammable & Solvent free 3-4 times stronger than standard P.V. High Solid content (51-53%) means more glue and it goes a lot further Does everything a P.V.A does, plus more Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.
$8.13
Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications. Same formula & product you trust, just better looking! Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable. Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age. It is non-toxic, non-flammable & Solvent free 3-4 times stronger than standard P.V. High Solid content (51-53%) means more glue and it goes a lot further Does everything a P.V.A does, plus more Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.
$103.00
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$12.75
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.00
You have seen 48 out of 81 products
Low-hazard, solvent-free choices that minimise fumes and emissions while delivering reliable bonds and seals. Ideal for occupied spaces and sensitive environments. Use filters to refine by chemistry, cure profile and finish. Always check the product page and TDS/SDS for application and safety details.
