Gorilla Clear Grip® is a flexible, fast-setting, crystal clear contact adhesive that creates a strong, permanent bond. Gorilla Clear Grip® is paintable and waterproof making it great for projects both inside and out! Build, Repair, Craft™ PRODUCT FEATURES WATERPROOF – For indoor/outdoor use FAST GRAB – Holds in just seconds PERMANENT BOND FLEXIBLE CRYSTAL CLEAR HEAVY DUTY NO-RUN FORMULA PAINTABLE PHOTO SAFE WASHER & DRYER SAFE BONDS: Metal, Glass, Fabric, Wood, Ceramic, Leather, Paper, Plastic*, and More! *Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces. All surfaces should be clean and free of dirt, grease and oil. Best if used between 10°C and 32.2°C. Clear Grip® should only be used in a well ventilated area. Apply adhesive to each surface to be bonded. To maximize bond strength: Wait approximately two minutes for adhesive to partially dry before joining surfaces. Press surfaces firmly together. NOTE: Bond forms immediately and can be difficult to reposition. Cure Time Allow for a minimum of 24 hours for full cure. Cure time may increase with lower temperatures and when used on non-porous surfaces. Storage Tips After each use, wipe nozzle with a dry cloth and tightly replace cap. Store in a cool, dry location. Tip: For easier re-opening, apply a thin coat of petroleum jelly to the threads before replacing cap. Store away from children and animals. Clean-up Wipe uncured adhesive with a dry cloth and clean with acetone, isopropyl alcohol, or citrus based solvents according to manufacturer’s instructions. Cured adhesive may be removed by scraping from surface. Paintable When fully cured. *NOTE: Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces. TECHNICAL SPECS APPLICATION TEMPERATURE – 10° to 32.2° C, best at room temperature OUTDOOR – Yes MOISTURE RESISTANT – Waterproof PAINTABLE – Yes – Can be painted with water and oil based paints, spray paint SANDABLE – Yes STAINABLE – Yes CURED COLOR – Clear STORAGE TIPS – Flammable adhesive, do not use or store near heat, sparks, flames, or while smoking. Store in a cool, dry location. Wipe nozzle clean before replacing cap, for easy re-open apply a thin coat of petroleum jelly to threads. GAP FILLING – No PHOTO SAFE – Yes WASHER & DRYER SAFE – Yes How should Gorilla Clear Grip® be stored? After each use, wipe nozzle with a dry cloth and tightly replace cap. Store in a cool, dry location. Tip: for easier re-opening, apply a thin coat of petroleum jelly to the threads before replacing cap. What surfaces does Clear Grip® adhere to? Gorilla Clear Grip® can be adhered to many surfaces including: Wood, Metal, Stone, Ceramic, Glass, Plastic*, PVC, Brick, Concrete, Foam, Paper, Rubber, Fabric, and Laminate. *NOTE: Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces. Is Gorilla Clear Grip® food safe? Clear Grip® should not be used around food. How do you clean up Gorilla Clear Grip®? When using Clear Grip®, it is best to wear safety glasses and chemical resistant gloves. To clean uncured adhesive: wipe uncured adhesive with a dry cloth and clean with acetone, isopropyl alcohol, or citrus based solvents according to manufacturer’s instructions. Cured adhesive may be removed by scraping from surface. See first aid treatment for skin contact. Is Gorilla Clear Grip® gap filling? No Is Gorilla Clear Grip® UV Resistant? Yes Can Gorilla Clear Grip® be used both indoors and outdoors? Yes, Gorilla Clear Grip® can be used both indoors and outdoors. Is Gorilla Clear Grip® stainable? Yes, Gorilla Clear Grip® is stainable when fully cured. Is Gorilla Clear Grip® sandable? Yes, cured Gorilla Clear Grip® is sandable. Is Gorilla Clear Grip® paintable? Yes, when fully cured. Is Gorilla Clear Grip® Washer/Dryer safe? Yes Is Gorilla Clear Grip® photo safe? Gorilla Clear Grip® is safe to use with photos.
$15.72
APPLICATION 1. Pierce seal at end of tube by turning nozzle and cap clockwise. 2. Ensure the working surface is clean, dry, free of dust or any grease. 3. Apply adhesive sparingly to one surface only. 4. Place surfaces together and press firmly for 10 - 60 seconds. Adequate for practical purposes after 30 minutes STORAGE: 5. After use. clean nozzle immediately with a cloth, replace cap and store upright between 5- 25°C. Avoid strong light and heat sources LIMITATION: Not recommended for polyethylene, polyester plastic & glass. Not suitable for use on items which contain hot liquids eg. Cups, mugs. May cause leather to discolour or harden. Test on a hidden area before use if in doubt. For interior use only.
$6.50
Davco® Sanitized Tile & Grout Sealer is a solvent-based sealer that provides excellent protection against stains, soiling, discolouration, and efflorescence. It’s an easy-to-apply, clear solution that cures to form an invisible, water-repellent coating. Key Benefits: Clear solution that cures to an invisible, water-repellent coating Easy to apply Usage: Surfaces: Only suitable for cement-based grouts Can be applied over most unglazed porous ceramic tiles Areas: Suitable for both interior and exterior applications Ideal for commercial and domestic wall and floor grout joints Advantages: Protects against stains, soiling, and discolouration Provides an invisible protective layer that repels water Perfect for enhancing the durability of grout in high-traffic areas
$20.98
Selleys Auto Fix Windscreen Sealant 100 mL - Black Stop leaks fast around windscreens and windows with a durable, weather resistant silicone seal. Selleys Auto Fix Windscreen Sealant forms a waterproof barrier that resists vibration, UV and temperature extremes, keeping water, dust and drafts out. Why choose this sealant 100 percent neutral cure silicone for reliable sealing Forms a waterproof seal to stop leaks quickly UV and weather resistant for long term performance Skins in 5 minutes and is touch dry in about 30 minutes Handles joint movement up to 25 percent Suitable surfaces Glass and windscreens Rubber surrounds and trims Painted surfaces and most plastics Metal frames and channels Typical applications Sealing between windscreen glass and rubber Sealing between rubber and metal frames Stopping minor water ingress around vehicle windows General sealing where a flexible, black silicone finish is desired Key specifications Technology Neutral cure silicone Colour Black Movement capability Up to 25 percent Skin time About 5 minutes Set time About 30 minutes Full cure Approximately 24 hours Service temperature -40°C to 180°C Application temperature -20°C to 50°C VOC 26 g/L Pack size 100 mL tube Directions Remove any dirt or moisture between the rubber and glass, or rubber and metal. Clean with mineral turpentine and allow to dry. Remove cap, unscrew nozzle, pierce inner seal, refit nozzle, then cut the tip at a 45 degree angle. Insert the nozzle between the rubber and glass or rubber and metal where possible. Squeeze the tube with steady pressure to push sealant into the joint. Smooth off with a gloved finger. If additional smoothing is needed, do it before the sealant skins. Clean up uncured sealant with mineral turpentine. Cured material must be cut or scraped away. Replace the cap after use. Allow sealant in the nozzle to cure, then remove before next use. Handy tips For neat lines, mask both sides of the joint and remove tape before the sealant skins. Best results occur when the joint is clean, dry and free of loose material. Limitations Not recommended on natural rubber, NBR or chloroprene neoprene due to poor adhesion. Clean up and storage Clean uncured sealant with mineral turpentine. Remove cured sealant by cutting or scraping. Store in a cool, dry place below 30°C. Use within 24 months of production. What you get 1 x Selleys Auto Fix Windscreen Sealant 100 mL - Black
$23.08
Bostik Super Glue Gel is a fast setting, non drip adhesive that stays where you put it for precise, clean bonds. The thixotropic gel formula is ideal for vertical surfaces and small gap filling, delivering reliable results on everyday repairs and crafts. Key features Fast setting gel for controlled application Non drip formula for vertical and overhead surfaces Small gap filling for close fitting parts Strong bond on many common materials Clear finish for neat repairs Ideal for Metal, rubber, most hard plastics, wood, ceramics, porcelain Small household repairs, models, craft and DIY fixes Precision bonding where liquid super glue may run Not suitable for Polyethylene, polypropylene, PTFE Very flexible materials or items regularly exposed to water immersion Food contact surfaces or aquarium use Directions Ensure surfaces are clean, dry and close fitting. Lightly roughen smooth surfaces if possible. Remove cap and apply a small bead of gel to one surface. A little goes a long way. Join parts immediately and hold firmly until set. Avoid moving the bond during curing. Allow the repair to rest for several minutes before light handling and longer for full strength. Handy tips Test on an inconspicuous area first. Use sparingly. Excess adhesive can slow cure. For porous materials, a second application may improve the bond. Clean up Wipe fresh squeeze out immediately. Once cured, carefully remove excess with a sharp blade. Adhesive may whiten on some surfaces if excess is left to cure. Storage and safety Close cap tightly after use and store upright in a cool, dry place. Bonds skin in seconds. Wear care when handling. If skin bonding occurs, do not pull apart. Soak in warm soapy water and gently roll apart. Use in a well ventilated area and keep out of reach of children.
$6.47
Bostik Repair All is a clear, multi-purpose adhesive for quick, durable repairs around the home, garage, and workshop. It bonds strongly, remains slightly flexible, and is water resistant once cured, making it suitable for everyday fixes and craft projects. Why you will love it Strong, long lasting bond Dries clear for a neat finish Water resistant once fully cured Flexible bond helps absorb vibration Suitable for indoor and outdoor use Works on Metal, wood, ceramics, glass, most rigid plastics, rubber, leather, fabric, and more. Always test on delicate or unknown materials first. Ideal for Household repairs and DIY Craft, hobbies, and school projects Fixing ornaments, toys, trims, and fittings Directions Ensure surfaces are clean, dry, and free of dust or grease. Lightly roughen smooth surfaces. Apply a thin even layer to one surface. Join parts together and press firmly. Support or clamp if needed. Wipe away any squeeze out immediately with a cloth dampened with solvent suitable for the substrate. Allow to set undisturbed. Handling strength is typically reached within hours. Full cure is usually achieved after 24 hours depending on bead size, temperature, and humidity. Clean up Uncured adhesive can be removed with a suitable solvent. Cured adhesive is best removed mechanically by trimming or carefully scraping. Good to know Not recommended for polyethylene, polypropylene, PTFE, or surfaces that will be in constant water immersion. Avoid contact with food or drinking water surfaces. Store upright in a cool dry place with cap tightly closed. Key details Brand Bostik Product Repair All Appearance Clear when dry Finish Flexible Water Resistance Yes, once cured Pack Size 20ml Always read the label and follow safety instructions. Keep out of reach of children.
$14.50
Overview This high-quality general-purpose silicone sealant is a versatile solution for a wide range of sealing and bonding applications. Engineered with neutral cure technology, it is designed to provide a durable, flexible, and weather-resistant seal that remains reliable even in demanding environments. Once cured, the sealant forms a strong rubber-like finish that is permanently elastic, ensuring long-lasting performance both indoors and outdoors. Key Features Neutral Cure Technology: Low-odor curing system suitable for sensitive applications. Permanently Flexible: Retains elasticity over time without cracking or shrinking. Waterproof Protection: Provides a watertight seal, protecting against leaks and moisture ingress. Interior & Exterior Use: Unaffected by rain, snow, extreme temperatures, or prolonged UV exposure. Excellent Adhesion: Bonds strongly to most common building materials without primer. Easy Application: Smooth flow from the tube, easy to tool and clean before curing. Applications This sealant is designed for general-purpose use across a variety of materials and environments. Its flexibility and adhesion make it suitable for: Sealing around window and door frames. Lap joints in metal guttering and roofing sheets. Bonding panels such as wood, plasterboard, insulation board, and drywall. Fixing masonry joints including sills, brickwork, and decorative trims. Gap filling around pipes, conduits, and penetration surfaces. General sealing in kitchens, bathrooms, and living areas where flexibility is required. Limitations Not suitable for permanent water immersion (e.g., underwater joints or continuous water load). Not recommended for use on polyethylene (PE), polypropylene (PP), polycarbonate (PC), polymethyl methacrylate (PMMA), PTFE, neoprene, bituminous surfaces, or very soft plastics. Not intended for deep cavity filling without adequate moisture for curing. Surface Preparation To ensure maximum performance, surfaces must be clean, dry, and free from dust, grease, or loose particles. Non-porous surfaces should be wiped with solvent and dried with a clean cloth. Porous surfaces should be lightly abraded or brushed to remove contaminants and improve adhesion. Complete any painting work before applying the sealant. Application Instructions Remove the cap and pierce the nozzle seal. Apply steadily along the joint or surface, ensuring continuous contact. Smooth or tool the bead before skin formation occurs. If masking tape is used, remove immediately after tooling to avoid tearing the cured seal. Curing At room temperature (23°C), the sealant will skin over within 15 minutes and achieve full cure within 24 hours, depending on humidity and joint depth. Once cured, it provides a permanently flexible and weatherproof joint. Cleaning & Maintenance Excess uncured sealant can be cleaned using a cloth dampened with mineral turpentine. Fully cured material should be trimmed away carefully with a sharp blade. Store unused tubes in a cool, dry place below 25°C and away from direct sunlight. Shelf life is up to 12 months from the date of manufacture. Health & Safety Use in a well-ventilated area. Avoid contact with eyes and mucous membranes, as uncured sealant may cause irritation. In case of contact with eyes, flush thoroughly with water and seek medical advice. Keep out of reach of children. Always follow safety instructions and refer to the product’s safety data for detailed guidance. Why Choose This General Purpose Silicone Sealant? This sealant is a trusted choice for tradespeople, DIY enthusiasts, and homeowners seeking a reliable solution for everyday sealing needs. Its combination of flexibility, adhesion, and weather resistance ensures that once applied, it continues to protect and bond effectively for years to come. Whether you are fixing a leaking gutter, sealing around windows, or bonding decorative trims, this product provides professional results with minimal effort. Technical Specifications Technology Neutral Cure Silicone Appearance Clear Paste Working Time Up to 15 minutes Tack-Free Time Approximately 15 minutes Full Cure at 23°C 24 hours Flexibility Permanently elastic after curing Weather Resistance Unaffected by rain, snow, UV, and temperature variations Applications Windows, doors, guttering, masonry, panels, pipes, decorative elements Storage Below 25°C, out of direct sunlight Shelf Life 12 months from manufacturing date
$9.98
UHU All Purpose Adhesives Super Strong & Safe, the super strong and super fast adhesive, which is adjustable - no instant finger bonding. Suitable for virtually all flexible, solid, porous and non-porous materials. Formula patented. Withstands vibrations and tremors. Moisture and heat resistant from -50°C to +100°C. Materials Universal - glues porcelain, ceramic, many plastic materials, metal, wood, glass, leather, rubber, Styrofoam®, paper, cardboard. Not suitable for leather clothing, textiles, PE and PP. Use and Handling Instructions Surfaces to be stuck together must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. Press parts together. Glue joint remains correctable for approx. 20 seconds. The thinner the film of adhesive, the stronger the bond.
$10.74
3 x 1g originally sealed tubes ideal portion for one application. in a handy storage box reaches the smallest corners and joints Extra strong super glue in 3 x 1g tubes, packaged in a small storage box, ensuring optimal quality for every new application. The liquid adhesive reaches the smallest corners and joints. Materials Glues many plastics, porcelain, ceramic, metal, wood and rubber. Not suitable for leather clothing, PE, PP nor styrofoam. Use and Handling Instructions Surfaces to be stuck together must fit exactly and must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. The thinner the film of adhesive, the stronger the bond. Press the parts together immediately and hold in place for a short time. Breathing upon the surfaces to be stuck will speed up bonding. After use, wipe the applicator tip dry and close firmly. Will last longer if stored in a cool place.
$11.50
SikaSeal®-401 Aquarium Premium one-component aquatic life safe silicone sealant SikaSeal® 401 Aquarium is a premium one-component room temperature vulcanising (RTV) silicone rubber that is safe for aquatic life and designed for sealing applications in aquariums, ponds and water pumps. It adheres very well to glass and aluminium, is UV resistant and has excellent gap filling properties. Extreme temperature resistance (-50°c to +250°c) Excellent vibration, UV and weathering resistance Good gap filling properties Usage Fish tanks Water pumps Aluminium Glass Advantages Extreme temperature resistance (-50°c to +250°c) Excellent vibration, UV and weathering resistance Good gap filling properties Highly versatile Easy to apply Aquarium safe Composition 1-C Silicone (acetoxy) Shelf life 18 months from date of production if in undamaged and unopened original sealed containers and stored according to the storage conditions. Storage conditions Must be stored in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Density ~1.02 kg/l Application Application steps SUBSTRATE PREPARATION Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue free solvent and allow to completely dry. CLEANING OF EQUIPMENT Uncured, excess SikaSeal® 401 Aquarium may be removed with Sika® Remover- 208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife. PRODUCT INFORMATION Composition 1-C Silicone (acetoxy) Packaging 75g Tube, 12 Tube per box Colour Clear Shelf life 18 months from date of production if in undamaged and unopened original sealed containers and stored according to the storage conditions. Storage conditions Must be stored in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Density ~1.02 kg/l Shore A Hardness ~23 Tensile Strength 1.0 N/mm2 Secant Tensile Modulus 1.1 n/mm2 Elongation at Break ~500% Ambient Air Temperature +5°c to +45°c Curing Rate ~3mm per 24 hours Skinning time ~7-10 minutes
$14.88
SIKA® FILLER 107 | PLASTER FILLER Premium, wet area, fine surface filler Fine surface filler that will not rehydrate in humid conditions such as kitchens and bathrooms Application thickness up to 4mm per layer Suitable for use in exterior situations when overpainted USE Sika® Filler 107 is suitable for interior surface filling work on plaster, woven fabrics, old wallpapers, etc. in wet environments such as kitchens and bathrooms etc. CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying Not sensitive to moisture Appearance / Colours Grey / blue, grey paste Packaging 500 ml plastic tube 5 l and 10 l plastic pail Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion Density ~ 1.050 kg/l Solid Content ~ 62% Grading Dmax : 0.15 mm Layer Thickness 4 mm max. Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-107 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-107 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-107 can be applied with a spatula in layer thicknesses from 0 - 4 mm. When filling deep holes or cracks above 4 mm the filler should be applied in several layers and must be allowed to almost dry before each subsequent layer is applied. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: 2 to 4 hours (thicker applications might require longer time) Paintability: Approx. 12 hours
$21.53
SIKA® FILLER 107 | PLASTER FILLER Premium, wet area, fine surface filler Fine surface filler that will not rehydrate in humid conditions such as kitchens and bathrooms Application thickness up to 4mm per layer Suitable for use in exterior situations when overpainted USE Sika® Filler 107 is suitable for interior surface filling work on plaster, woven fabrics, old wallpapers, etc. in wet environments such as kitchens and bathrooms etc. CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying Not sensitive to moisture Appearance / Colours Grey / blue, grey paste Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion Density ~ 1.050 kg/l Solid Content ~ 62% Grading Dmax : 0.15 mm Layer Thickness 4 mm max. Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-107 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-107 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-107 can be applied with a spatula in layer thicknesses from 0 - 4 mm. When filling deep holes or cracks above 4 mm the filler should be applied in several layers and must be allowed to almost dry before each subsequent layer is applied. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: 2 to 4 hours (thicker applications might require longer time) Paintability: Approx. 12 hours
$16.43
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$20.57
Key Features UV and weather resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non corrosive neutral cure formula Has superior flexibility +/- 25% movement capability Temperature resistance - approximately -60°C +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25 year guarantee* against crumbling, cracking and peeling away Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters. Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND How to Use Use in a well ventilated area. Avoid contact with skin and eyes. Thoroughly clean and dry surface from oil, dirt and grease with mineral turps. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun. Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps. Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal. Limitation: • Not paintable. Complete painting 7 days prior to applying sealant. • Not recommended for use as a plug for burst pipes. • Do not use in below waterline applications. ^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy. *Warranty Information * Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010. Clean up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
$12.00
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$19.12
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$9.00
Liquid Nails Fast is a water-based high strength (*) construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. After drying it is beige (light tan) in colour. Uses Liquid Nails Fast has high initial (immediate) grab which reduces the need to support joins while the adhesive cures. The initial grab works best with porous surfaces. It will bond to many building materials including MDF, particle board, timber, plaster board, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results are achieved when at least one surface is porous. Liquid Nails Fast would typically be used for the following applications: Areas where nailing is not desirable Skirting boards, architraves, cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding minimises slippage when adhering on vertical surfaces Meets or exceeds AS 2329-1999 (Mastic adhesives for fixing wall boards) Does not drip, sag or string between panels Bridges gaps and will adhere materials with uneven surfaces Low mess – excess and squeeze out is easily cleaned up with wet cloth No solvent fumes – ideal for large indoor jobs High flexibility – will withstand thermal movement and vibration High heat resistance – will not lose bonds exposed to sun Paintable when dry Easy to extrude at all temperatures Application Tips Liquid Nails Fast should always be used in conjunction with permanent mechanical fasteners except in low stress applications such as wall panelling and fixing light weight objects. (Bonds may creep under constant heavy loads.) Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications. In cold or damp weather and between non-porous materials drying time is greatly extended Thick applications take longer to dry than thin applications Pre-test plastics to determine suitable bonding. Adheres well to UPVC. Not suitable for polyethylene and polypropylene. For wood flooring applications Liquid Nails (solvent based) is recommended. [Liquid Nails Fast is satisfactory for fixing sheet flooring (particleboard/ply) to joists in conjunction with the manufacturer’s minimum nailing specification but is not recommended for fixing sheet wood flooring to flat surfaces such as existing or concrete floors. Technical Details and Performance For porous substrates good bond strength is achieved after 24 hours and will continue to strengthen over 2-3 day period. Time for strong bond depends on nature and conditions of application. In cold or damp weather and between non-porous materials, drying time is greatly extended. Indicative information only, not to be used for setting specifications. Appearance Lump free, air-free smooth beige paste Specific Gravity Approx. 1.44g/mL @ 25oC Viscosity Typical 7000 – 9000 Poise Slump Typical: 0mm Shear Adhesion Strength (7 days) (AS2329) Greater than 1500kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure) Typical 40N/25mm (wire gauze off hoop pine.(Variant to AS2329)) Initial Bond Strength AS2329-1999D (Tested after 24 hrs) Over 200kPa Heat Resistance Bonds will resist temporary exposure to temperatures up to 140oC. Constant high temperatures will reduce constant load holding power (see below). Creep resistance (under constant load)*2 Fully cured *1 bonds of 625 sq. mm will hold up to 500g loads (7.8kPa) in shear at constant 80oC Fully cured *1 bonds of 625 sq.mm will hold up to 100kPa in shear at 25oC (equivalent to 6Kg load on 625 sq.mm bond area) Coverage 15 metres of a 5mm diameter bead 1mm thick bonds on porous substrates cured at least 7 days at temps above 25oC This data is provided as indicative only. Not to be used for design purposes. Thick bonds reduce constant load holding power and increase curing time. Larger bond areas increase curing time. Cleaning Liquid Nails Fast may be cleaned off with hot soapy water or a damp cloth while still wet. Dry adhesive is best removed by scraping or peeling.
$15.33
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints. For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting Properties Ready to use Sand & paint after 4 hours Super smooth white finish Easy to sand Maximum depth: 2 mm Particle size: Max 0.10 mm How to apply Substrate and crack must be clean, dry and free from loose material. New wood should be primed first. Rub down gloss surfaces for improved adhesion. Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer. Apply with a filling knife and spread over the surface, pressing in well. Remove any excess filler and leave to dry. For an even smoother finish rub down with fine sand paper. Use appropriate protection when sanding. Do not apply when the surface temperature is below + 5°C. Replace lid after use. Wash tools with warm water.
$13.90
Nordsjö Professional Light and Smooth Super Filler, fills without the need for sanding. Thanks to our unique lightweight technology, our Light and Smooth filler immediately gives you a smooth finish. It does not sag and is easy to model, making it ideal for ceilings and walls. High performance extra lightweight filler for all general interior and exterior repairs Fills deep cracks and holes up to 10cm in plasterboard, wood, fiber cement, concrete, brick and most other common building materials Ideal for over-head applications (non-slump formula) Properties Ready to use Will not shrink or sag Super smooth finish – no sanding required Paintable with all types of paint Maximum layer thickness: 5 cm Maximum depth: 10 cm Easy to apply and shape Quick drying: paint after approx. 2 hours (5 cm layer at 20°C) with water-based paints How to apply Substrate must be clean, dry, dust and grease free. Remove all loose materials. Before application, metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer. Stir into a smooth paste (if the filler is too dry, just add a few drops of water). Press filler into hole with a filling knife, smoothing off with a wet filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. No sanding is required. If sanding, wait for 24 hours. If painting over with an oil-based finish, wait 14 days. Must be painted over when used outside (minimum 2 coats). Colour: White. Not suitable for drilling. Clean tools and hands immediately after use with warm water. Do not store or use below 5 ° C.
$12.90
Nordsjö Professional Rapid Repair Filler quickly fills small cracks and holes, such as drill and nail holes. It adheres perfectly to stone, concrete, drywall, plaster and stucco. For filling and repairing small cracks and holes, such as drill holes and nails Excellent adhesion to plasterboard, wood, brick, concrete, fiber cement, drywall, plaster and render Not for use on metal, plastic, PVC and damp surfaces Suitable for interior & exterior use Tools Needed Sharp Knife Fine Sandpaper Properties Ready to use Rapid dry: sand and paint after 15 minutes (5 mm layer at 20°C) with all types of paint Easy to sand Will not shrink Accepts nails and screws Maximum layer thickness: 5 mm Maximum depth: 5 mm Must be painted over when used outside (minimum 2 coats) Colour: White How to apply Substrate must be clean, dry, dust and grease free. Remove all loose materials. Mix the product well before use. Press filler into crack with a filling knife, smoothing off with a wet filling knife. For deeper repairs, build up in layers of 5 mm, letting the product dry in between layers. Remove any excess filler and leave to dry. Once dry sand lightly if required. Clean tools and hands with warm water immediately after use. Do not store or use below 5°C.
$13.90
Nordsjö Professional Flexible Wood Filler repairs small cracks and holes in wood. As the name implies, it is a flexible filling for wood, great for interior and exterior use. Suitable for all types of interior & exterior wood Quick drying, easy to sand Water resistant finish will not shrink, crack or crumble Stainable and paintable Properties Ready for use Excellent adhesion to all types of wood Tough and durable fill that flexes with the natural movement of wood Accepts nails and screws Sandable and paintable after approx. 3 hours (1 cm layer at 20°C) Must be overcoated when used outside (minimum 2 coats) Paintable with all types of paint Maximum layer thickness: 1 cm Maximum depth: 2 cm Colour: natural/pine How to apply Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix the product well before use. Product can be applied directly from the pot. Apply filler firmly into the hole with a filling knife. For a smooth result, finish with a damp filling knife. For deeper repairs, build up in layers of 1cm, letting the product dry in between layers. Once dry, sand the filler so it is even with the surface and dust off. Finish with a stain, varnish or paint. The filler may stain or varnish differently to the surrounding wood. Clean tools with warm water. Do not store or use below 5°C.
$15.50
![Monarch Mini Gap Filler [White]](http://gluesaustralia.com.au/cdn/shop/files/9320090029080_1b178ddb-e3de-4ec1-83bb-8e320595bdb3.jpg?v=1754712311&width=645)
$2.84
![Monarch Mini Gap Filler [Cream]](http://gluesaustralia.com.au/cdn/shop/files/9320090030581_c5a95353-e7ee-4d92-8445-93066291f976.jpg?v=1754712313&width=645)
$6.02
![Monarch Mini Gap Filler [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090030567_dd3b7bac-a9e5-4986-9275-2bff35fb52de.jpg?v=1754712316&width=645)
$6.02
Monarch Mini Fill Sand Go™ MONARCH MINI® FILL SAND GO™ is an all in one solution to almost every DIY filling repair job. It’s a quick-dry, ready mixed, water-based formula that is suitable for small to medium cracks and holes in plasterboard & timber surfaces. The innovative MONARCH MINI® FILL SAND GO™ is a 3 in 1 product solution that includes a filling blade applicator as well as an ingenious sanding tool with a reversible sanding sponge. This allows you to complete the filling repair from start to finish without the hassle of requiring extra tools. FEATURES Innovative 3 in 1 Solution Filler, Applicator & Sanding Puck with Sponge All included Suitable for Interior repairs on Plasterboard & Timber BENEFITS Quick Dry Formula Ready to Use Multi-Purpose Filler Paintable Sandable Low Shrinkage UV Resistant Low Odour
$14.04
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
$10.86
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. PRODUCT FEATURES CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More APPLICATION TEMPERATURE – 0°C to 37.8° C, best at room temperature SERVICE TEMPERATURE – -28.9° to 82.2° C OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – Minimal What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight fitting joints. It’s perfect for a fix you need done fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also minimally gap filling, which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant, and can withstand intermittent exposures, however is not meant for a constant soak. Original Gorilla Glue is 100% waterproof and can withstand soaking and longer term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$14.92
APPLICATION 1. Pierce seal at end of tube by turning nozzle and cap clockwise. 2. Ensure the working surface is clean, dry, free of dust or any grease. 3. Apply adhesive sparingly to one surface only. 4. Place surfaces together and press firmly for 10 - 60 seconds. Adequate for practical purposes after 30 minutes STORAGE: 5. After use. clean nozzle immediately with a cloth, replace cap and store upright between 5- 25°C. Avoid strong light and heat sources LIMITATION: Not recommended for polyethylene, polyester plastic & glass. Not suitable for use on items which contain hot liquids eg. Cups, mugs. May cause leather to discolour or harden. Test on a hidden area before use if in doubt. For interior use only.
$4.50
A water-based protective sealer which penetrates and cures within the pores of the grout. The sealer is fast drying and the bottle contains a brush for easy application. A water-based protective sealer Deep penetrating into the grout Easy to use brush for perfect sealing over grout Fast drying formula Coverage Seals up to 25m2 per 250ml
$20.03
Davco® Sanitized Glue Grout A Pre-mixed, Ready-to-Use Wall Tile Adhesive and Grout Davco® Sanitized Glue Grout is a flexible, white, pre-mixed adhesive and grout for internal wall tile applications. Ideal for thin bed fixing of porous-backed ceramic tiles, it’s suitable for domestic areas like bathrooms, kitchens, and laundries. Key Features: White appearance Pre-mixed and ready for immediate use Dual-purpose: serves as both adhesive and grout Ideal for fixing lifted or popped tiles No wastage Usage: Surfaces: Cement renders Rendered brickwork and blockwork Plasterboard Fibre-cement wall sheets Tiles: Suitable for thin-bed fixing of most porous-backed ceramic tiles Areas: Interior applications, including domestic walls, bathrooms, kitchens, and laundries Advantages: Ready to use, no mixing required Suitable for adhesive and grout in one product Convenient for quick repairs or installations No product wastage Packaging & Colour: Packaging: 500g pail Colour: White paste Application Information: Adjustability Time: 20-30 minutes (depending on climate and substrate porosity) Ready for Use: 24 hours Note: Drying time may vary based on climate, substrate, and tile porosity. Coverage: A 500ml tub of Davco® Sanitized Glue Grout covers approximately 0.5m² when applied with a 6mm notched trowel as an adhesive. Application Steps: Surface Preparation: Ensure all surfaces are structurally sound, dry, clean, and free of contaminants like oil, grease, or loose material. Deeply contaminated surfaces should be abraded to expose at least 80% of the original substrate. Follow these preparation guidelines: Substrate Specific Requirement Primer Rendered brick/blockwork Cured minimum 7 days, sound Davco PrimeX or Ultraprime Fibre-cement sheet/plasterboard Correctly and firmly fixed Davco PrimeX or Ultraprime Previously painted surfaces Sand back to expose 80% of surface Davco PrimeX or Ultraprime Mixing: No mixing required. Davco® Sanitized Glue Grout is ready to use straight from the pail.
$24.79
You have seen 78 out of 78 products
Compact tubes for targeted application and small repairs—great in tight spaces and for on-the-go fixes. Typical formats include gel super glues, small sealant tubes and repair compounds. Apply a thin, even film; re-cap promptly to prevent curing in the tip. Use filters to refine by chemistry, cure speed and clean-up. Always check the product page and TDS/SDS for suitability and instructions.
