Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$26.05
Gorilla Heavy Duty Mounting Tape is a double-sided tape that mounts in an instant, for a long-lasting, weatherproof bond. The industrial strength double-sided tape delivers a heavy-duty bond that holds up to 30 pounds. Gorilla Heavy Duty Mounting Tape is perfect for indoor and outdoor projects and sticks to smooth and rough surfaces. Completing DIY projects is easy with this tough, double-sided tape. Mount, build, and repair! Features: DOUBLE SIDED TAPE – coated with adhesive on both sides for easy hanging. 30lb STRONG HOLD – Sticks to smooth and rough surfaces.* INSTANT HOLD – Delivers a fast & easy permanent bond. WEATHERPROOF – For indoor and outdoor use. BOND: Plastic**, Metal, Wood, Glass, Brick, Ceramic, Stone & More! Directions: Apply tape to back of object vertically, allowing for even distribution of weight. Avoid touching surface of tape. Note: Apply 2” of tape per 1lb of weight Cut tape and press to secure the tape to object. Remove clear liner and align the object to desired placement. Press firmly, as Gorilla Mounting Tape conforms to the surface and creates a strong, PERMANENT bond. Specs: APPLICATION TEMPERATURE – above 50° F SERVICE TEMPERATURE – continuous- up to 194° F intermittent- up to 302° F OUTDOOR – Yes MOISTURE RESISTANT – Yes STORAGE TIPS – Store in a cool, dry location. 64° to 72° F, 30 to 70% RH. FAQs Is Gorilla Mounting Tape food safe? Gorilla Mounting Tape is not recommended for direct or indirect food contact and should not be considered food safe. How do I remove Gorilla Mounting Tape from my surface? Gorilla Mounting Tape is a permanent tape and may cause surface damage. If the object must be removed, the mounted object must be removed first. This may best be achieved by prying from one corner. Next, the mounting tape can be removed by slowly stretching the tape parallel to the surface. Will Gorilla Mounting Tape work on plastic/vinyl/rubber? Gorilla Mounting Tape works well on many plastics, however, it does not work on certain low surface energy plastics, such as polyethylene (PE) and polypropylene (PP), or certain types of rubber with high oil or plasticizer content. How do I remove the liner on Gorilla Mounting Tape? The liner should be removed once the tape is applied to object. Lift the liner from the corner by using your fingernail, edge of the product blister card, or a blade. The liner may also be removed by pinching and stretching the corner of the Mounting Tape at a 40-degree angle to the surface, until the liner lifts.
$14.03
Holds up to 13.6Kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$11.55
Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$28.21
![Sika Sikaflex Pro+ Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$24.84
UHU All Purpose Adhesives Super Strong & Safe, the super strong and super fast adhesive, which is adjustable - no instant finger bonding. Suitable for virtually all flexible, solid, porous and non-porous materials. Formula patented. Withstands vibrations and tremors. Moisture and heat resistant from -50°C to +100°C. Materials Universal - glues porcelain, ceramic, many plastic materials, metal, wood, glass, leather, rubber, Styrofoam®, paper, cardboard. Not suitable for leather clothing, textiles, PE and PP. Use and Handling Instructions Surfaces to be stuck together must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. Press parts together. Glue joint remains correctable for approx. 20 seconds. The thinner the film of adhesive, the stronger the bond.
$10.74
![Sika Sikaflex 252 High Strength Structural Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/7612895456188_c10ea96d-b0be-41ba-a0ee-9656fab35b16.jpg?v=1754711652&width=645)
Elastic adhesive for vehicle assembly bonding Sikaflex®-252 is an elastic 1-component polyurethane adhesive especially designed for bonding large components in vehicle assembly. It is suitable for bonding coated metal, GRP, ceramic materials and plastics. Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties PRODUCT BENEFITS Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties Can be painted Vibration-damping Electrically non-conductive Usage Sikaflex®-252 is suitable for assemblies that are subject to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminum (including anodized components), sheet steel (including phosphated, chromated and galvanized components), metal primers and paint coatings (2-component systems), ceramic materials and plastics. Seek manufacturer’s advice before using on plastics that are prone to stress cracking. This product is suitable for professional experienced users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
$53.62
Sikaflex®-291 Tube Black: Marine-Grade, Multipurpose Polyurethane Sealant Product Benefits IMO Certified Bonds to a wide variety of substrates Good ageing and weathering resistance Elastic and low odour Non-corrosive, Overpaintable and Sandable Usage Sikaflex®-291 is a multipurpose product suitable for marine constructions. It is ideal for making elastic, vibration-resistant joint seals and can also be used for interior sealing applications. Application Information Surface preparation is key. Surfaces must be clean, dry and free from grease, oil, and dust. Further application tips can be found in the Sika Pre-treatment Chart for Marine Applications. Additional Details Application Temperature: 5 ? 40 °C Skin Time: 60 minutes Shore A Hardness: 40 Shelf Life: 12 months when stored below 25°C
$17.76
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524002800_e901daee-d941-4c51-bb2c-fdfedd9a6316.jpg?v=1754711662&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$27.48
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$27.48
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$27.72
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$27.72
SikaTitan® 258 is a primerless to windscreen, one-component direct glazing adhesive. It is easy to apply and has a paste-like consistency. On exposure to atmospheric moisture it cures to a durable elastomer. SikaTitan® -258 provides a long tack-free time and ensures a safe application even under warm conditions. Note: Primerless application requires the glass to be prepared with a non-antistatic glass cleaner. Also the bonding surfaces must be free of contamination prior to the application of the adhesive. SikaTitan® -258 is manufactured in accordance with ISO 9001 / 14001 quality assurance system and with the responsible care program. Product Benefits - Primerless to glass - One-component formulation - Cold application - Good application properties such as bead stability / good non-sag properties - Short cut-off string - Tested according to FMVSS 212/208 (with double-side airbags, no seatbelts) Areas of Application SikaTitan® -258 is suitable for direct-glazing applications in the Automotive Glass Replacement business. With its good performance and application properties it is suitable for mobile as well as inhouse installations.This product is to be used by professional experienced fitters only. If this product is used for other applications than Automotive Glass Replacement, trials must be carried out prior to use. Technical Product Data Chemical base 1-C polyurethane Colour (CQP1) 001-1) Black Cure mechanism Moisture-curing Density (uncured) (CQP 006-4) 1.1 kg/l approx. Non-sag properties (CQP 061-1) Good Application temperature +5 to +40°C Skin time2) (CQP 019-1) 40min. approx. Open time2) (CQP 526-1) 30min. approx. Curing speed(CQP 049-1) Shore A hardness (CQP 023-1 / ISO 868) 51 approx. Tensile strength (CQP 036-1 / ISO 37) 5 MPa approx. Elongation at break (CQP 036-1 / ISO 37) 650% approx. Tensile lap-shear strength (CQP 046-1 / ISO 4587) 2.5 MPa approx. Safe Drive-Away Time2) (cars) with double side airbag according to FMVSS 212 / 208 (CQP 511-1) without airbag 6 hours 2 hours Chemical Resistance SikaTitan® -258 is resistant to fresh water, seawater, limewater, sewage effluent, diluted acids and caustic solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic acids and caustic solutions or solvents. Method of Application Removal of old glass Remove damaged glass in accordance with the vehicle manufacturer’s instructions. Surface preparation Surfaces must be clean, dry and free from dust and grease. The bond faces must be prepared with a non-antistatic glass cleaner. Bonding surface must be free of contaminants before application of the product. Windshields without ceramic coatings need additional UV protection. Application Cut off the tip of the nozzle in accordance with the vehicle manufacturer's recommendations and screw onto the cartridge. It is recommended to apply the adhesive with a piston-type application gun. To ensure a uniform thickness of adhesive bead, we recommend that the adhesive be applied in the form of a triangular bead (see fig. 1 below). The substrate temperature must be between 5°C and 35°C.
$43.58
![Sika Sikaflex 291 Marine Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb9d6399-3f9c-4c6e-aeb9-97604f6829a6.jpg?v=1754711703&width=645)
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck. Why Choose Sikaflex®-291 Excellent adhesion to common marine substrates Good ageing & weathering resistance for long service life Elastic to absorb vibration and movement Low odour and non-corrosive Overpaintable and sandable after cure* Available colours: White, Grey, Black *Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area. Typical Uses Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications. Suitable Substrates Wood Metals, metal primers and 2-component paint systems Ceramic materials Plastics such as GRP (fibreglass), etc. Do Not Use On Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate) Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility. Technical Data (Typical) Property Method / Note Value Chemical base — 1-component polyurethane Cure mechanism — Moisture-curing Colour CQP001-1 White, Grey, Black Density (uncured) — ~1.3 kg/L (colour-dependent) Non-sag properties — Good Application temperature Ambient 5 – 40 °C (optimum 15 – 25 °C) Skin time CQP019-1 (A) ~60 minutes Open time CQP526-1 (A) ~45 minutes Curing speed CQP049-1 Depends on temperature & humidity (see TDS) Shrinkage CQP014-1 ~5 % Shore A hardness CQP023-1 / ISO 48-4 ~40 Tensile strength CQP036-1 / ISO 527 ~1.8 MPa Elongation at break CQP036-1 / ISO 527 ~500 % Tear resistance CQP045-1 / ISO 34 ~6 N/mm Service temperature (continuous) CQP513-1 −50 to +90 °C Service temperature (short-term) CQP513-1 +160 °C (4 h), +180 °C (1 h) Shelf life (B) 12 months (store < 25 °C) CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C. Application Guidance Surface Preparation Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates. Application Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity. Optimum substrate and product temperature is 15 – 25 °C. Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment. Tooling & Finishing Tool within the skin time. Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability). Cleaning & Removal Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent. Cured material: remove mechanically (e.g. knife, wire, abrasion). Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin. Overpainting Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting. If the paint requires baking > 80 °C, allow the sealant to fully cure first. Always conduct preliminary trials under manufacturing conditions. Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area. Compliance & Approvals Meets requirements set out by the International Maritime Organization (IMO). Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable. FAQs Can Sikaflex®-291 be overpainted? Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area. What is a “marine grade” sealant/adhesive? Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline. When and why should a primer be used? Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing. What does the Wheelmark indicate? The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED). Which substrates does Sikaflex®-291 bond to? Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate). How do I remove Sikaflex®-291? Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material. Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
$28.97
![Sika Sikaflex 291 Marine Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb4dfb0d-a336-4739-9b91-9ca89764b874.jpg?v=1754711704&width=645)
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck. Why Choose Sikaflex®-291 Excellent adhesion to common marine substrates Good ageing & weathering resistance for long service life Elastic to absorb vibration and movement Low odour and non-corrosive Overpaintable and sandable after cure* Available colours: White, Grey, Black *Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area. Typical Uses Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications. Suitable Substrates Wood Metals, metal primers and 2-component paint systems Ceramic materials Plastics such as GRP (fibreglass), etc. Do Not Use On Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate) Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility. Technical Data (Typical) Property Method / Note Value Chemical base — 1-component polyurethane Cure mechanism — Moisture-curing Colour CQP001-1 White, Grey, Black Density (uncured) — ~1.3 kg/L (colour-dependent) Non-sag properties — Good Application temperature Ambient 5 – 40 °C (optimum 15 – 25 °C) Skin time CQP019-1 (A) ~60 minutes Open time CQP526-1 (A) ~45 minutes Curing speed CQP049-1 Depends on temperature & humidity (see TDS) Shrinkage CQP014-1 ~5 % Shore A hardness CQP023-1 / ISO 48-4 ~40 Tensile strength CQP036-1 / ISO 527 ~1.8 MPa Elongation at break CQP036-1 / ISO 527 ~500 % Tear resistance CQP045-1 / ISO 34 ~6 N/mm Service temperature (continuous) CQP513-1 −50 to +90 °C Service temperature (short-term) CQP513-1 +160 °C (4 h), +180 °C (1 h) Shelf life (B) 12 months (store < 25 °C) CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C. Application Guidance Surface Preparation Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates. Application Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity. Optimum substrate and product temperature is 15 – 25 °C. Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment. Tooling & Finishing Tool within the skin time. Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability). Cleaning & Removal Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent. Cured material: remove mechanically (e.g. knife, wire, abrasion). Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin. Overpainting Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting. If the paint requires baking > 80 °C, allow the sealant to fully cure first. Always conduct preliminary trials under manufacturing conditions. Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area. Compliance & Approvals Meets requirements set out by the International Maritime Organization (IMO). Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable. FAQs Can Sikaflex®-291 be overpainted? Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area. What is a “marine grade” sealant/adhesive? Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline. When and why should a primer be used? Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing. What does the Wheelmark indicate? The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED). Which substrates does Sikaflex®-291 bond to? Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate). How do I remove Sikaflex®-291? Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material. Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
$28.97
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895456164_5c293f0a-df90-415e-875b-0ed963018cfa.jpg?v=1754711706&width=645)
High strength, structural grade polyurethane adhesive sealant High strength elastic adhesive, suitable for structural joints subjected to high dynamic stress Suitable for use on trucks, trailers and caravans with excellent adhesion to timber, metals, primers and paint coatings Vibration dampening USE Sikaflex® 252 is suitable for structural joints that will be subjected to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminium (incl. anodized components), sheet steel (incl. phosphated, chromated and zinc-plated components), metal primers and paint coatings (2-c systems), ceramic materials and plastics. CHARACTERISTICS AND ADVANTAGES 1-C formulation Elastic Can be overpainted Good gap-filling properties Capable of withstanding high dynamic stresses Vibration Damping Non-corrosive Electrically non-conductive Bonds well to a wide variety of substrates
$53.62
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524003593_20527af7-fe08-426c-ab91-1e7cb16de683.png?v=1754711708&width=645)
Multi-purpose adhesive sealant with a wide adhesion range Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals. Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted PRODUCT BENEFITS Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted Passes EN45545-2 R1/R7 HL3 Non-corrosive Low odour NSF-approved for incidental food contact Potable water approved (meets AS4020 requirements) Usage Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Surface preparation Surfaces must be clean, dry and free from grease, oil and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry. Tooling and finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use. Removal Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin. Overpainting Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
$38.04
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003395_211a040d-fd65-46e4-b320-62196c5157c2.png?v=1754711709&width=645)
Multi-purpose adhesive sealant with a wide adhesion range Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals. Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted PRODUCT BENEFITS Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted Passes EN45545-2 R1/R7 HL3 Non-corrosive Low odour NSF-approved for incidental food contact Potable water approved (meets AS4020 requirements) Usage Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Surface preparation Surfaces must be clean, dry and free from grease, oil and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry. Tooling and finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use. Removal Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin. Overpainting Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
$38.04
Sika AnchorFix®-1 is a high-performance, styrene-free chemical anchoring adhesive designed for fast and reliable installations in both construction and DIY projects. This two-component, solvent-free, polyester-based adhesive is ideal for securing rebars, threaded rods, bolts, and special fastening systems in concrete, hollow and solid masonry, hard natural stone, and solid rock. It cures rapidly, even in low temperatures, and can be applied using standard guns. Advantages: Fast curing Compatible with standard guns Usable in low temperatures High load capacity ETA approved Non-sag, even overhead Styrene-free Low odor and wastage Technical Information: Compressive Strength: ~60 N/mm² (7 days, +20°C) Modulus of Elasticity in Compression: ~3,500 N/mm² Tensile Strength in Flexure: ~28 N/mm² Tensile Strength: ~12 N/mm² Temperature Resistance: +50°C (long-term), +80°C (short-term) Glass Transition Temperature: +60°C Color: Component A: White Component B: Black Mixed: Light grey Usage: Ideal for various grades of rebars, threaded rods, bolts, and special fastening systems. Substrates may vary, so testing is recommended to ensure suitability, especially with natural stones. Always ensure the substrate is clean, dry, and free of contaminants. Perform pull-out tests if the substrate strength is unknown. Mixing and Application: Mix the components in a 10:1 ratio by volume. The material must be between +5°C and +40°C for application. Ensure the substrate temperature is between -10°C and +40°C. Shelf Life and Storage: Shelf life is 12 months from the date of production when stored properly. Store in unopened, sealed, and undamaged packaging in dry conditions between +5°C and +25°C. Curing Times: +30°C: Open time 4 minutes, Curing time 35 minutes +25°C: Open time 4 minutes, Curing time 40 minutes +20°C: Open time 5 minutes, Curing time 50 minutes +10°C: Open time 6 minutes, Curing time 85 minutes +5°C: Open time 10 minutes, Curing time 145 minutes -10°C: Open time 30 minutes, Curing time 24 hours Approvals and Certifications: Complies with NCC 2019 reference to AS 5216:2018 for post-installed and cast-in fastenings in concrete. ETA-approved for use in masonry and non-cracked concrete, with CE marking. Cleaning of Equipment: Clean tools with Sika® Colma Cleaner immediately after use. Hardened material can only be removed mechanically. For detailed design considerations, refer to "Technical Documentation Sika AnchorFix®-1" (Ref: 870 43 01).
$38.30
Selleys MarineFlex delivers a waterproof seal for joints & gaps, even under water*. Suitable for boats, pools & spas. MarineFlex high-performance adhesive sealant can be used on boats, pools & spas, where you need a waterproof seal or bond, even underwater* It can be applied & will cure under water – no need to drain your pool or spa. Compared to traditional polyurethanes it provides a more durable seal & bond with superior UV resistance. Features Salt, fresh & chlorinated water (pools/spas)^ Above and below the waterline No primer required Shock absorbing & vibration dampening Solvent & isocyanate free Sandable when fully cured Powered by Sil-X advanced polymer technology Limitations #Not suitable for PP, PE or PTFE *critical seals/repairs underwater should be regularly checked & repaired if required. Not for polycarbonate and Perspex underwater ^Gelcoat must be lightly sanded prior to product application Where can this product be used? Suitable for boats, pools & spas^ What materials is this product suitable for? Metals Glass Ceramic Tiles Sealed/painted timber & concrete Fibreglass Gelcoat* Most plastics# (pre-test before use)
$23.68
![Selleys Storm Sealant [Grey] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/9300697128881_05baffa7-20d9-4ff2-9039-79bd0c8a796b.png?v=1754711779&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$23.09
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/9300697126047_24fe6e74-fe07-4d10-9db0-38dc98c383c8.png?v=1754711781&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$23.09
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$23.09
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$10.84
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$7.40
A premium grade, high strength construction adhesive that delivers a weather resistant, strong, flexible and shock resistance bond that is useful in many landscaping projects. Uses Ideal for landscape jobs such as: Stabilise stone and interlocking masonry retaining walls Bonding pavers to concrete Bonding capstones to wall Repairing rockeries Seal between treated pine logs to reduce soil loss Stabilise loose stone steps Technical Features Strengthens and increases the life of dry stone and interlocking masonry walls High flexibility to withstand seasonal movement and temperature extremes Excellent adhesion to sound concrete and similar materials UV resistant and long lasting in all weather extremes Low odour during application Non corrosive Gap filling Application Tips Cannot be painted over Not recommended for permanent water immersion applications If re-positioning materials, fresh adhesive must be applied to achieve bonding Not suitable for adhering loose soft crumbly materials New concrete etc will not adhere to cured adhesive All surfaces must be sound, dry and free from oil, grease, loose powdery material. If necessary, use mineral turpentine to clean surface and allow to dry. Cut cartridge tip, fit nozzle and cut nozzle tip to a suitable size opening (approximately 5mm). Place cartridge into caulking gun. Apply ‘dobs’ or ‘beads’ of adhesive of appropriate thickness to ensure sufficient contact and spread between both surfaces. (To minimise ‘squeezed out’ apply at least 12mm in from edges) Immediately bring surfaces together before product skins (within 5 minutes) and apply sufficient pressure to spread between both surfaces Do not wipe ‘squeeze out’. Wait until product cures and remove by trimming with a sharp blade, but avoid cutting into the bond. Leave bond undisturbed until adhesive cures sufficiently. Do not allow traffic on stairs or use of walls for at least 24 hours after adhesive application. Do not apply to wet/damp surfaces Technical Details and Performance Liquid Nails Landscape will skin and begin curing within 5 minutes. Full cure will normally be achieved in 72 hours. Indicative information only, not to be used for setting specifications. Consistency (As applied) Non-slump, solvent free paste Curing Mechanism Very rapidly develops rubber consistency by reaction with moisture from the air Curing Rate 2mm depth per day Skin Forming Time 10-15 minutes (depending on weather conditions) Service Temperature –60°C to +150°C Lap Shear Bond Strength (Hoop Pine to Hoop Pine at 1.6mm thick adhesive, 500sq mm bond area) After 7 days: 570KPa Coverage 15 metres of a 5mm diameter bead Cleaning Clean all excess adhesive from equipment before it cures with a cloth dampened with mineral turpentine or acetone. Once cured adhesive is extremely difficult to remove and must be abraded or trimmed with a knife. Spilt of smeared adhesive is best left to cure and then removed by abrasion.
$19.15
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697127631_b26581e9-d1ac-46a3-9fab-c85c02a2717c.jpg?v=1754711902&width=645)
$15.72
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697127624_07bbc12d-036a-4edb-b049-761036f32c9b.jpg?v=1754711904&width=645)
$17.08
Flexiseal FC is a fast curing polyurethane Adhesive and Sealant with high flexibility and excellent adhesion. Waterproof+, suitable for indoor and outdoor applications^, paintable after it has cured. Best for : Common building materials such as concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics*. Product Details Where can this product be used? External wall and cladding joints Weatherproofing joints between brickwork, masonry, wood concrete or metal frames Joints in walls, balconies, around window or door frames Joints in bridge and balcony parapets Retaining walls Roofing Acoustic rated walls What materials is this product suitable for? Common building materials such as concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics*. *Will not adhere to PE, PP or PTFE–test other plastics and rubber first. How to Use AS AN ADHESIVE: Apply a bead or small blobs on surface. Assemble parts together and clamp firmly to hold until cured. Remove excess immediately. Initial bond achieved in 24 hours depending on temperature and humidity. Bond strength increases over a few days. AS A SEALANT: Extrude sealant into the joint ensuring full contact with the sides of joint. Avoid entrapment of air. Smooth sealant with spatula forcing it into the joint. For best performance, install joint backing rod (polyethylene or polyurethane foam rod) in the joint to control depth and ensure joint movement. Suitable for +/- 25% joint movement. Complies with ISO11600/F/25HM. Limitations: *Will not adhere to PE, PP or PTFE–test other plastics and rubber first. ^To maximise durability in outdoor applications paint with a suitable exterior paint. Some colours may discolour after exposure to UV radiation. +Not suitable for permanent water immersion or below water line use. Clean Up Mineral turps. Cured product can only be removed mechanically
$20.70
Selleys MarineFlex delivers a waterproof seal for joints & gaps, even under water*. Suitable for boats, pools & spas. MarineFlex high-performance adhesive sealant can be used on boats, pools & spas, where you need a waterproof seal or bond, even underwater* It can be applied & will cure under water – no need to drain your pool or spa. Compared to traditional polyurethanes it provides a more durable seal & bond with superior UV resistance. Features Salt, fresh & chlorinated water (pools/spas)^ Above and below the waterline No primer required Shock absorbing & vibration dampening Solvent & isocyanate free Sandable when fully cured Powered by Sil-X advanced polymer technology Limitations #Not suitable for PP, PE or PTFE *critical seals/repairs underwater should be regularly checked & repaired if required. Not for polycarbonate and Perspex underwater ^Gelcoat must be lightly sanded prior to product application Where can this product be used? Suitable for boats, pools & spas^ What materials is this product suitable for? Metals Glass Ceramic Tiles Sealed/painted timber & concrete Fibreglass Gelcoat* Most plastics# (pre-test before use)
$23.20
![Selleys Armour Flex High Performance Adhesive [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697125279_ca037dae-5a32-46a8-b3b3-d4b80d5f85fd.jpg?v=1754711933&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$32.27
Selleys 650FC: The Ultimate Adhesive Sealant Powered by Advanced Hybrid Technology Key Features +/- 20% Joint movement capability Excellent UV & Weather Resistance Superior Strength & Instant Grab Can be applied on damp surfaces Applications This product can be used in various applications such as trafficable joints, air conditioning ducting, caravan construction, perimeter seals around doors, windows, and general interior joint sealing. Compatibility Highly compatible with most building materials including timber, concrete, metals, and more. Not suitable for PVC, polyethylene, and temperatures above 80°C. How to Use Ensure surfaces are clean and dry. Apply using a sealant gun and spread evenly within 10 minutes. Storage and Cleanup Store in cool, dry conditions below 30°C. Uncured product can be removed with mineral turps. Precautions This product is not suitable for constantly submerged joints or temperatures beyond 80°C.
$22.79
![Selleys 401 Silicone Adhesive for Gaskets Resists 205 Degrees [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697606976_8b2f5b6d-5036-4991-bd89-df84ec600f6f.jpg?v=1754711964&width=645)
Silicone 401 RTV is a one part ready to use, acid cure, room temperature vulcanising (RTV), silicone adhesive sealant. It cures rapidly on exposure to atmospheric moisture to form a versatile, durable, resilient silicone rubber. It is available in clear. Uses Silicone 401 is suitable for form-in-place gaskets and for adhesive, sealing and electrical insulating applications in manufacturing and plant maintenance. Technical Features Wide Temperature Tolerance: Remains permanently flexible under operating temperatures from – 60oC to 205oC, and will tolerate short periods of 260oC Good Chemical Resistance: Good resistance to most organic and inorganic chemicals, solvents and oils Primerless Adhesion: Adheres without primer to many metal, glass, ceramic, rigid plastic, rubber painted and wood substrates Non-toxic: Suitable for incidental food contact in food handling equipment and food contact surfaces Excellent Weatherability: Excellent resistance to ozone, UV light and ageing Good Electrical Insulating Properties: Insulating properties are comparable to other insulating rubbers at room temperature, though performs better than many other rubbers at higher temperatures and water has little effect on these properties Application Tips Not recommended for use with petrol, distillate and some other hydrocarbon solvents. These can cause softening and swelling which is undesirable in some applications. Do not use in totally confined joints where sealant is not exposed to atmospheric moisture Chemical compatibility should be tested for each application under consideration Cannot be over-painted Technical Details and Performance Indicative information only, not to be used for setting specifications. Typical Application Properties Consistency Non – sag, gun grade Tack Free Time (25oC, 50% r.h.): 15 – 20 minutes Skin Forming Time 5 to 10 minutes (depending on weather conditions) Cure Time (3mm Section @ 25oC, 50% R.H.): 24 hours Shrinkage During Curing Approximately 3.5% by volume Specific Gravity 1.04 Storage Life (Below 30oC in original unopened container):12 months Typical Mechanical Performance Properties (3 day cure @ 25oC, 50% R.H.) Tensile Strength (MPa) 1.2 Ultimate Elongation % 400 Hardness (Shore A) 25 Tear Strength (N/mm) 5.0 Joint Movement Capability ± 25% Typical Electrical Properties (at Room Temperature) Dielectric Strength kv/mm 21 Dielectric Constant @50Hz to 5MHz 2.6-2.8 Dissipation Factor Tan @50Hz-5MHz 20×10-4 to 5×10-4 Volume Resistivity (ohm-cm) 1×1013 (wet 60oC) 1×1014 (dry 23oC) Typical Thermal Properties Brittle Point –60oC Maximum Continuous Operating Temperatures 205oC Maximum Intermittent Operating Temperatures 260oC
$30.59
The unique rubber-infused gel formula allows powerful bonds that are extremely precise even on flexible materials. Ideal for porous and vertical surfaces, and strong enough to withstand extreme conditions. The gel’s high strength non-drip formula then dries transparent to form invisible bonds that give a long lasting durability that is both weather and shock-resistant. For intricate, hard to reach spots, Loctite Power Flex Gel Control features an easy grip squeeze bottle and nozzle for precise applications. Recommended on: Rubber, Leather, Wood, Metal, Porcelain, Paper, Plastic. Properties: -Rubber infused gel formula for extra strong and flexible bonds -Ideal for porous and vertical surfaces -Water resistant -Bonds in seconds -Withstands heavy loads -Dries transparent -Easy to open, self-piercing and anti-clog cap -Choice of applicators: convenient tube or easy grip control with a longer nozzle -Suitable for use on most surfaces* -Solvent-free -* Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Step by Step Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$11.36
Loctite Extreme Glue No Drip Gel contains a revolutionary Flextec formulation that fuses multiple materials together for a long-lasting bond. When a project or repair requires an adhesive with a higher viscosity and advanced resistance to extreme conditions, this liquid gel is your new go-to. This versatile, gap-filling glue seals and repairs nearly any surface, and it’s perfect for harsh conditions where constant flexing is a problem. Loctite Extreme Glue No Drip Gel dries clear and minimizes dripping for a clean, professional finish on any household project. It’s even dishwasher safe! Plus, our glue is durable enough to use outdoors because it cures quickly and is resistant to vibration, impact, moisture, UV exposure, and extreme temperatures. No Drip Gel is great for vertical applications Withstands vibration, impact, moisture, and UV light Strong and durable for long-lasting results Use as an indoor or outdoor glue Crystal-clear formula for a clean, professional look Water-resistant and temperature-resistant from -58° to 248° F Gap-filling gel for imperfect-fitting surfaces Flexible bond and precise grip
$12.13
Retaining Compound - medium strength. If disassembly is required. Ideal for parts that need subsequent dismantling. LOCTITE® 641 is designed for the bonding of cylindrical fitting parts, particularly where disassembly is required for servicing operations. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings Technical Information Colour Yellow Diametrical Clearance (Maximum) 0.1 mm Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.1 mm Shear Strength Unit, Steel psi Shear Strength, Steel 1700 Specific Gravity 1.07 g/l Specific Gravity Temperature 25 °C Substrates Metal: Steel Temperature -65 - 300 °F Viscosity 525 - 1950 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$22.40
LOCTITE 263 is designed for the permanent locking and sealing of threaded fasteners. The product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. It's particularly suited for heavy duty applications such as studs into motor housings, nuts onto studs in pump housings and other fasteners where high strength is required. LOCTITE 263 provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids. Recommended on High strength Locks studs against vibration loosening Controlled/torque tension Prevents thread corrosion Fast curing How to use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole. For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours. Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush. For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 4. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 5. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 6. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 7. Assemble and tighten as required For Disassembly 1. Apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush
$14.98
Threadlocking Adhesive - medium strength. General purpose. Suitable for all metal threaded assemblies. LOCTITE® 243 is a general purpose threadlocker of medium bond strength. This threadlocker secures and seal bolts, nuts and studs to prevent loosening due to vibration. The product works on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces. It is proven to be tolerant of minor contamination due to industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids. Prevents loosening on vibrating assemblies, e.g. pumps, gearboxes or presses. Works on all metals, including passive substrates (e.g. stainless steel, aluminium, plated surfaces). Proven to tolerate minor contamination by industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids Permits disassembly with hand tools for servicing Technology: Acrylic Chemical Type: Dimethacrylate ester Appearance (uncured) Blue liquidLMS Fluorescence Positive under UV lightLMS Components One component - requires no mixing Viscosity Medium, thixotropic Cure Anaerobic Secondary Cure Activator Application Threadlocking Strength Medium LOCTITE® 243™ is designed for the locking and sealing of threaded fasteners which require normal disassembly with standard hand toolsThe product cures when confined in the absence of air between close fitting metal surfaces and prevents loosening and leakage from shock and vibration. The thixotropic nature of LOCTITE® 243™ reduces the migration of liquid product after application to the substrateLOCTITE® 243™ provides robust curing performance. It not only works on active metals (e.g. brass, copper) but also on passive substrates such as stainless steel and plated surfaces. The product offers high-temperature performance and oil tolerance. It tolerates minor surface contaminations from various oils, such as cutting, lubrication, anti-corrosion and protection fluids GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as a sealant for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Safety Data Sheet (SDS). Where aqueous washing systems are used to clean the surfaces before bonding, it is important to check for compatibility of the washing solution with the adhesive. In some cases, these aqueous washes can affect the cure and performance of the adhesive. This product is not normally recommended for use on plastics (particularly thermoplastic materials where stress cracking of the plastic could result). Users are recommended to confirm the compatibility of the product with such substrates. Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry 2. If the cure speed is too slow, use appropriate activator. Please see the Cure Speed vs. Activator graph for reference. Allow the activator to dry when needed 3. Shake the product thoroughly before use 4. To prevent the product from clogging in the nozzle, do not allow the tip to touch metal surfaces during application 5. For Thru Holes, apply several drops of the product onto the bolt at the nut engagement area 6. For Blind Holes, apply several drops of the product to the lower third of the internal threads in the blind hole, or the bottom of the blind hole 7. For Sealing Applications, apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also 8. Assemble and tighten as required For Disassembly 1. Remove with standard hand tools 2. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250 °C. Disassemble while hot 3. Apply localized heat to the assembly to approximately 250 °C. Disassemble while hot For Cleanup 1. Cured product can be removed with a combination of soaking in a LOCTITE® solvent and mechanical abrasion such as a wire brush
$17.12
Loctite 222 Threadlocker prevents corrosion, loosening from shock or vibration, and seals to prevent leakage. It also allows for simple, hand tool disassembly without shearing the screw. Easy to remove, it is typically used with small screws up to 1/4 inch. Recommended on Low strength Stops vibration loosening of screws and seals against leakage Prevents thread corrosion Dismantle with normal hand tools How to Use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole. For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours. Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush. For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot.
$19.23
Hold It Australia T90 PENETRATOR Wicking Grade for Close Fitting Parts - 50ml Description: HOLDIT AUSTRALIA T90 Penetrant is a fast-curing, low viscosity anaerobic compound that seeks voids in assembled components to cure anaerobically on close-fitting metal parts. It's ideal for securing tightly fitted assemblies. Applications T90 is excellent for post-assembly application, effectively preventing loosening of metal threaded fasteners. It is suitable for securing parts with minimal clearance and repairing hairline cracks in metal castings. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. For porosity or hairline cracks in casting products, brush directly onto the parts. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Hold It Australia T77 STUDLOCK High Strength for Bolts 25mm and Above - 50ml Description: HOLDIT AUSTRALIA T77 Studlock large diameter high strength threadlocker is a red, general purpose adhesive for permanent threaded assemblies. It effectively locks fasteners 1 and larger in diameter, providing a seal against leakage and corrosion while resisting attacks from lubricants and industrial liquids and gases. Applications Ideal for eliminating double nutting/welding in critical assemblies. T77 allows for reduced casting thickness and prevents cracked castings from interference fit stresses. Suitable for larger diameter studs with coarse threads and can be used to reclaim worn stud holes. Primers are recommended for large gaps and poorly fitting parts. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
Hold It Australia T22 SCREWLOCK Low Strength for Easy Disassembly - 50ml Description: HOLDIT AUSTRALIA T22 Screwlock is a low strength, anaerobic thread locking compound, ideal for locking threaded fasteners that require disassembly with standard hand tools. It performs excellently on aluminium, steel, plated, stainless steel, and special alloy parts. T22 is characterized by its good temperature and solvent resistance. Applications T22 is specifically formulated to lock and seal small screws (less than ¼), including set screws with long engagement lengths. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry for optimal results. If the metal is inactive or the cure speed is too slow, apply HOLDIT AUSTRALIA AA471 Activator or HOLDIT AUSTRALIA AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow to fully cure before applying load. Properties of Uncured Material Chemical Type: Anaerobic Colour: Purple Toxicity: Low Solid Content: 100% Viscosity @ 25°C, cPs: 900-1,500 cps Specific Gravity: 1.05 Shelf Life: 24 months Performance of Cured Material Fixture Speed: 15-20 Min @ 22°C Full Cure: 24 Hours @ 22°C Temperature Range: -50°C to 150°C Product Conformity: MIL-S-46163A, ASTM D-5363, NSF Technical Datasheet The cure speed of HOLDIT AUSTRALIA T22 is dependent on temperature and substrate. The product shows a breakaway strength of 1Nm 9Nm on 3/8 plain steel nut & bolt after 1 hour and 5Nm 11Nm after 24 hours. On a 3/8 zinc nut & bolt, the strength is 1Nm 4Nm after 24 hours. Environmental and Fluid Resistance Heat Age: 100% retention in Engine oil @ 150°C Brake Fluid @ 150°C: 85% retention ATF @ 150°C: 85% retention 50/50 water/ethylene glycol @ 120°C: 80% retention Water @ 100°C: 80% retention Gasoline @ 25°C: 95% retention Diesel Fuel @ 25°C: 100% retention Ethyl Alcohol @ 25°C: 90% retention Active & Inactive Metal Table Category Cure Speed Metals Super Active Very Fast Cure Brass, Copper, Magnesium Active Fast Cure Iron, Steel, Nickel, Aluminium Inactive Slow Cure Stainless Steel, Titanium, Zinc Passive Primer Necessary Anodized Aluminium, Galvanised Steel, Ceramics, Glass, Plastics, Painted Finishes
$34.86
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. PRODUCT FEATURES CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More APPLICATION TEMPERATURE – 0°C to 37.8° C, best at room temperature SERVICE TEMPERATURE – -28.9° to 82.2° C OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – Minimal What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight fitting joints. It’s perfect for a fix you need done fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also minimally gap filling, which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant, and can withstand intermittent exposures, however is not meant for a constant soak. Original Gorilla Glue is 100% waterproof and can withstand soaking and longer term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$14.92
Davco SMP Evo Tile Adhesive is a high-performance, flexible cement-based adhesive ideal for the installation of natural stone, porcelain, and marble tiles. Specially designed with advanced low-dust technology, it provides a cleaner and safer working environment. Its superior non-slump properties make it perfect for wall and floor tiling, including large-format tiles. Surface Preparation: Ensure surfaces are structurally sound, dry, and free from contaminants like dust, oil, and wax. Smooth surfaces should be roughened slightly, and absorbent substrates should be primed. Existing tiles must be clean, dry, and securely bonded. Mixing: Mix 5kg of powder with approximately 1.4–1.5L of clean water using a mechanical mixer until a smooth, lump-free paste is formed. Allow it to stand for 5 minutes before remixing. Do not add more water after mixing. Application: Apply the adhesive with a notched trowel over an area no larger than can be tiled within the open time. Firmly press tiles into the adhesive bed with a twisting motion to ensure full contact. Back-buttering may be necessary for large tiles or uneven substrates. Coverage: Approximately 1.5–1.75m² per 5kg bag using a 10mm notch trowel. Drying Time: Tiles can generally be grouted after 24 hours. Allow 2 days before exposure to water in wet areas and 21 days for submerged areas like pools. Clean-up: Clean tools and excess adhesive with water before it sets. Once cured, adhesive must be removed mechanically. Technical Data: Classification: C2S1TE Pot life: 1.5 hours Open time: 30 minutes Adjustability time: 20 minutes VOC content: Low Appearance: White powder
$30.14
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/9310492265001_6fb5fccc-7784-41bb-9997-bbd917e3c834.png?v=1754712704&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$22.51
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9310492265025_0316718a-8147-4bdd-955a-19d6d8a0bc59.png?v=1754712705&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$23.45
A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$25.07
A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength after 3 days. Features: -Araldite is stronger than other glues due to the chemical reaction of the two parts -Bonds a variety of surfaces -Dries Clear -Very Strong, durable bonding -Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) -Forms a rigid, durable bond -Can be used for gap filling (surfaces need not mate closely) -Good chemical resistance -Heat Resistant -Clamping is recommended to achieve a stronger bond -Not suitable for bonding plastics such as Polypropylene and Polyethylene -Bond strength weakens above 80°C but strength is regained when temperature drops Appearance: Translucent Where can this product be used? -Load bearing repairs -Gluing the head back on your hammer -Fixing loose table or chair legs. -Bonding solid pieces of Aluminium sheeting -Bonding timber on your boat -Repairing splits and cracks in Cricket bats -Bonding fibreglass sheets -Repairing Ski’s -Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? -Glass -Metal -Wood -Fabric -Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics -Crystal -Leather How to use this product -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each -Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. Handy tips -For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. -To extend product life replace caps immediately after use. Ensure you wipe excess from the nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. -When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) -Wipe off any uncured Araldite with acetone or nail polish remover. -To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. -To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. -Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. -Clamping recommended for a stronger bond. -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. -Ensure the surface is dry before applying the product. Safety tips: -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Do not use solvents near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention -Non-toxic when set. -For further information refer to the Material Safety Data Sheet (MSDS). -Storage and re-use -Ensure caps are replaced and product stored in a cool dry place.
$20.05
You have seen 48 out of 52 products
Formulations that maintain bond integrity under vibration and shock, ideal for vehicles, machinery and equipment. Consider threadlockers for fasteners and toughened systems for bonded joints. Use filters to refine by chemistry and temperature rating. Always review the product page and TDS/SDS.
