Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$8.57
Earl’s MiracleWipes – Innovative, Professional-Grade Cleaning Wipes Meet the jobsite and workshop essential that takes on the messes others can’t. MiracleWipes® are purpose-built to remove tough contaminants like oil-based paint, latex paint, epoxy, spray paint, stain, grease, oils, adhesives, ink, and grime from hands, tools, and surfaces. The unique absorbent-lock design grabs and traps residue so it doesn’t smear, while the low-solvent formula is surface and skin safe when used as directed. Dual-texture wipes (scrub on one side, smooth on the other) give you the control to lift heavy build-up then finish clean. Seeing is believing! Why You’ll Love It Removes paint & epoxy fast: Cuts through wet and semi-cured paints, epoxies, stains, grease and more. Absorb & lock technology: Traps mess in the wipe to reduce smearing and re-depositing. Dual-texture performance: Textured side agitates; smooth side finishes clean. Low solvent, professional grade: Powerful on mess, considerate on common jobsite materials. Surface & skin safe: Designed for hands, tools, and non-porous surfaces when used as directed. Large wipe size: 12" × 6" sheets give you more cleaning area per pull. Clean, no-rinse finish: Leaves no heavy, oily residue; dries quickly. Smart canister: One-at-a-time dispense with a tight snap-seal lid to keep wipes fresh. Where It Works Ideal for use on: Hands & skin: Great for cleanup after painting or epoxy work (avoid eyes, mouth, and broken skin). Tools & equipment: Brushes, rollers, spray guns, trowels, mixers, blades, scrapers. Common surfaces: Metals, coated plastics, laminates, sealed wood, glass, tiles, stone benchtops (sealed), vinyl & PVC. Prep before painting: Wipe down to remove dust, light oils, fingerprints and shop grime prior to coating. Always test on an inconspicuous area first. Not recommended for unfinished leather, delicate textiles, or uncured high-gloss finishes. How To Use Open the snap-seal lid and pull one wipe through the dispenser. Use the textured side first to loosen paint, epoxy, grease, or grime. Flip to the smooth side to lift away residue and finish clean. For stubborn spots, hold the wipe against the area briefly, then wipe again. Repeat with a fresh wipe if needed. Close the lid firmly after each use to prevent drying out. Dispose of wipes in the bin—do not flush. Pro Tips Epoxy cleanup: Tackle while epoxy is wet or green for fastest results. Surface prep: After wiping, allow to air dry, then apply coatings per product directions. Electronics & sensitive parts: Power down first; use a lightly damp section of the wipe and avoid pooling liquid. Frequently Asked Questions Will MiracleWipes remove fully cured epoxy?They excel on wet and semi-cured residues. Fully cured epoxy typically requires mechanical removal; wipes help with final cleanup. Are they safe on skin?Yes when used as directed on hands. Avoid contact with eyes and broken skin. Rinse with water after heavy use if desired. Do they leave residue before painting?The low-residue formula dries quickly. For best coating adhesion, allow the surface to dry or give a quick final wipe with a clean, dry cloth. Can I use them on automotive paint or delicate finishes?Test first in a hidden spot, especially on fresh or uncured coatings. Are the wipes flushable?No. Dispose of used wipes in general waste. What’s In The Pack Count: 90 pre-moistened, dual-texture wipes Wipe size: 12" × 6" (approx. 30.5 × 15.2 cm) Dispenser: Resealable snap-seal canister Storage & Handling Keep lid closed to prevent drying. Store upright in a cool, dry place. Keep out of reach of children. Use in a well-ventilated area. Do not ingest. Do not flush. Specifications Brand Earl’s Product MiracleWipes® – Innovative Cleaning Wipes Primary Use Removal of paint (oil & latex), epoxy, spray paint, stain, grease, oils, adhesives, inks, and grime Wipe Construction Dual-texture (scrub + smooth), high-absorbency lock design Wipe Size 12" × 6" (approx. 30.5 × 15.2 cm) Pack Size 90 wipes per canister Solvent Level Low solvent Skin/Surface Safety Surface & skin safe when used as directed Residue Low-residue, fast-dry Country of Manufacture Made in the USA Dispensing One-at-a-time pull through snap-seal lid Disposal General waste only; do not flush Suggested Applications Trade & DIY paint cleanup (rollers, brushes, sprayers, trays) Epoxy projects (boats, composites, woodwork, crafts) Auto & equipment maintenance (oils, grease, grime) Site prep and tidy between coats Workshops, garages, construction, facilities maintenance
$29.00
Glue Dots Flexible Hang Tabs Brand: GlueDots Make decorating effortless and worry free. Glue Dots Flexible Hang Tabs give you a fast, clean and removable way to hang balloons, banners, streamers, paper lanterns, lightweight garlands, bunting, ornaments and more. The crystal clear tabs apply in seconds, hold firmly to most smooth household and event surfaces, and remove cleanly when the party is over. Damage free: removes cleanly from most properly painted, sealed and smooth surfaces when used as directed. Instant bond: pressure sensitive adhesive grips on contact for quick setup. Crystal clear: low visual impact for a neat, professional look in photos and in person. Flexible design: engineered slot holds standard latex balloons without helium, plus tabs act as anchor points for string, ribbon or fine wire. No tools, no mess: no nails, pins, tacks or putty required. Indoor friendly: ideal for homes, venues, classrooms, offices and display windows. Why choose Flexible Hang Tabs From last minute birthday setups to polished corporate events, these tabs are your decorating shortcut. The flexible slot lets you slide in a balloon neck or thread ribbon, while the clear base keeps the focus on your décor. When it is time to pack down, the removable adhesive lets you lift and peel without gouging walls or leaving sticky residue. Versatile surfaces: painted walls, sealed plaster, varnished timber, tile, glass, metal, laminate and most smooth plastics. Looks better: clear tabs virtually disappear against most backgrounds. Saves time: decorate large areas quickly with repeatable placement. Reliable hold: grips evenly across the tab to help prevent droop. Great for Balloon walls and garlands without helium Banners, bunting and streamers across hallways or backdrops Paper lanterns, pom poms and lightweight ornaments from ceilings Classroom displays and noticeboards where pins are not allowed Retail window dressing and temporary point-of-sale displays Wedding, engagement, baby shower and seasonal décor How to use Prepare the surface: ensure it is clean, dry, smooth and free of dust, oils and cleaning sprays. Fresh paint should be fully cured. Peel and place: remove a tab from the liner, align and press firmly for several seconds to ensure full contact. Hang décor: slide a balloon neck into the slot or thread ribbon, cord or lightweight line through the tab opening. Adjust if needed: for best results, reposition immediately after placement before full bond develops. Removal and clean up To remove, gently lift a corner of the tab and peel it back slowly over itself at a low angle. If resistance is felt, pause and continue slowly. On delicate finishes, test in an inconspicuous area first. Dispose of tabs with household waste. No solvents or scraping required when used as directed. Pro tips Use multiple tabs to distribute weight across wider banners or garlands. Avoid textured, dusty, damp or porous surfaces which reduce adhesion. For ceiling applications, ensure the surface is smooth and dust free. Allow items that were stored cold to reach room temperature before use. Indoor use recommended. Prolonged exposure to moisture, heat or direct sunlight may reduce performance. Safety and care Keep out of reach of small children. Not a toy. Do not use to hang valuable, fragile or irreplaceable items. Always test on a small area of the surface if uncertain. Specifications Brand GlueDots Product name Flexible Hang Tabs Colour Clear Adhesive type Pressure sensitive, removable Finish Crystal clear, low profile Recommended use Indoor, temporary decorating and light display mounting Suitable surfaces Painted and sealed walls, sealed plaster, varnished wood, tile, glass, metal, laminate, most smooth plastics Unsuitable surfaces Textured, dusty, damp, porous, unsealed or flaking finishes Residue on removal Removes cleanly when used as directed on suitable surfaces Repositionable Yes, during initial placement Operating conditions Room temperature, dry environment Applications Balloons, streamers, banners, paper lanterns, pom poms, lightweight ornaments Tools required None Country of use Suitable for Australian homes, venues and classrooms Performance can vary with substrate, surface preparation and environmental conditions. Always follow the directions and test before full application. What you get Flexible, clear hang tabs on an easy peel liner. Pack quantities vary by selection. Choose the pack size that suits your event or display plan. Storage Store in a cool, dry place away from dust and direct sunlight. Keep in original packaging until use to protect adhesive surfaces. Plan your next event From birthdays to window displays, build cleaner backdrops and crisper lines with Glue Dots Flexible Hang Tabs. Add to cart and get decorating in minutes.
$13.00
![Waxstix Timber repair wax touch-up crayons [Baltic Pine]](http://gluesaustralia.com.au/cdn/shop/files/9315284510000.png?v=1754724098&width=645)
![Waxstix Timber repair wax touch-up crayons [Cedar]](http://gluesaustralia.com.au/cdn/shop/files/9315284510017.png?v=1754724098&width=645)
Colours to suit almost any timberWaxstix are so easy to use and so handy for quick repairs to scratched or damaged timber. Waxstix can be coated and stained. Plus, Waxstix contain no beeswax so they will not leave any white ring marking otherwise known as the "halo effect". For most small scratches, simply rub the stick over the damaged area. For larger, deeper indentations (where TIMBERMATE water-based Woodfiller cannot be used), heat a knife blade with a flame or a soldering iron or stove lighter and fill the damaged area with hot wax. Remove excess wax by rubbing with the smooth side of sandpaper, a piece of cardboard or an old credit card. Use a cotton cloth to buff and remove excess wax.
$6.51
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$24.43
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$12.75
Contact Cement is a flexible acrylic contact adhesive used to bond tile, rubber, wood, metal, formica, most plastics and much more. Pacer Technology Super Glue Contact Cement (T-CC) is a single component flexible acrylic contact adhesive that remains flexible after cure and is best used for: • Tile • Rubber • Wood • Metal • Masonite • Particle Board • Plywood • Leather • Formica • Plastic • Laminates PROPERTIES: Initial Color: Amber Dry Time: 30 minutes Final Color: Amber Full Strength: 24 hours Open Time: 10 minutes Operating Temperature Range: 15° to 150°F -9° to 66°C Instructions: Use in a well-ventilated area. 1. Surfaces should be clean and dry. For best results, use fine sandpaper to roughen the surface. 2. Apply Contact Cement to both surfaces and wait 10 minutes. 3. Press parts together. Clamp heavier parts together. Allow 30 minutes for drying time. 4. For optimum strength in all applications, wait 24 hours before using the repaired object. 5. Clean off tube or bottle top and tightly cap adhesive. Store upright and away from heat sources. Note: Solvents may evaporate from bottle or tube if left open for prolonged periods. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains methyl ethyl ketone, hexane and ethyl acetate. Warning – liquid adhesive is extremely flammable. Harmful or fatal if swallowed. Injurious to eyes with direct contact. Avoid prolonged breathing of vapours and prolonged skin contact. Wear suitable protective clothing and gloves. Use and store in a well-ventilated area away from heat, sparks or flame. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN.
$7.95
Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance. Incredible bond strength Waterproof Superior strength Adheres to even visibly damp surfaces Fast curing - less than 30 minutes Materials: wood, ceramic, stone, concrete, metal, glass, fibreglass, leather, laminate, masonry, plasterboard and some plastics.
$25.98
Tarzans Grip Mega Bond Glue is suitable for bonding large variety of surfacees in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resitance. Incredible bond strength Waterproof Adheres to even visibly damp surfaces Fast curing - less than 30 minutes
$10.50
Overview: Selleys White For Life Wet Area Waterproof Silicone Sealant is a premium, 100% silicone sealant designed to provide a long-lasting, waterproof, and mould-resistant seal in high-moisture areas such as bathrooms, kitchens, and laundries. Its advanced formulation ensures the sealant remains brilliant white over time, resisting yellowing, staining, and blackening. Surface Preparation: Ensure all surfaces are clean, dry, and free from dirt, dust, oil, and loose materials. Clean the area with mineral turpentine and wipe dry with a clean cloth before application. Application Instructions: Cut the nozzle at a 45° angle to the desired bead size. Cut the cartridge tip and fit the nozzle. Place the cartridge into a caulking gun and apply steady pressure to ensure the sealant is pushed into the joint. Tool the sealant with a spatula dipped in detergent water within 5-10 minutes of application for a smooth finish. Clean up any excess sealant with mineral turpentine before it skins. Allow the sealant to cure fully, which typically takes 72 hours. Coverage: The coverage depends on the joint size; for example, a 5mm x 5mm joint will yield approximately 12 linear meters per 300g cartridge. Drying Time: The sealant skins in about 10 minutes and cures fully in 72 hours. Clean-Up: Uncured sealant can be removed with mineral turpentine. Once cured, the sealant is extremely difficult to remove and must be abraded or trimmed with a knife. Technical Data: Technology: Acetic cure silicone Colour: White Density: 1.05 g/cm³ Shore A Hardness: Approximately 20 Tensile Strength: 1.5 MPa Elongation at Break: 400% Service Temperature Range: -60°C to +150°C
$17.00
![Selleys Wet Area Sealant EZI Press [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125415_d295dbcb-92c9-46a5-87c2-399a71ec73f3.png?v=1754711757&width=645)
Selleys Wet Area Ezi Press is ready to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and resistance to unsightly mould. Ideal for wet areas like bathrooms and kitchens. Best for : Ceramic, glazed and porcelain fixtures, Metal, copper and brass fittings, Powder coated aluminium, Aluminium, Plastic laminates, Rubber, Glass, Stainless steel, Concrete Features No caulking gun required Easy to hold and use Superior waterproof seal 100% silicone - resists cracking, crumbling or peeling away Mould resistant Precision application for the best finish Where can this product be used? Showers Baths Spas Sinks Metal, copper and brass plumbing Fixtures What materials is this product suitable for? Ceramic, glazed and porcelain fixtures Metal, copper and brass fittings Powder coated aluminium Aluminium Plastic laminates Rubber Glass Stainless steel Concrete Size 100g Aerosol can Technology Neutral Cure Silicone Use Interior How to Use Use in a well ventilated area. Avoid contact with skin and eyes. 1. Throughly clean and dry surface from oil, dirt and grease with mineral turps. 2. Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense. 3. Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap 4. Sealant will fully cure in 72 hours Limitations: • Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. • Sealant is not paintable.Complete painting 7days prior to applying sealant. • Not for aquariums or contact with food, eating utensils or drinking water.
$14.77
![Selleys Wet Area Sealant EZI Press [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125750_81b22ff4-49f4-4011-b6d5-6ee33f923b0f.jpg?v=1754711759&width=645)
Selleys Wet Area Ezi Press is ready to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and resistance to unsightly mould. Ideal for wet areas like bathrooms and kitchens. Best for : Ceramic, glazed and porcelain fixtures, Metal, copper and brass fittings, Powder coated aluminium, Aluminium, Plastic laminates, Rubber, Glass, Stainless steel, Concrete Features No caulking gun required Easy to hold and use Superior waterproof seal 100% silicone - resists cracking, crumbling or peeling away Mould resistant Precision application for the best finish Where can this product be used? Showers Baths Spas Sinks Metal, copper and brass plumbing Fixtures What materials is this product suitable for? Ceramic, glazed and porcelain fixtures Metal, copper and brass fittings Powder coated aluminium Aluminium Plastic laminates Rubber Glass Stainless steel Concrete Size 100g Aerosol can Technology Neutral Cure Silicone Use Interior How to Use Use in a well ventilated area. Avoid contact with skin and eyes. 1. Throughly clean and dry surface from oil, dirt and grease with mineral turps. 2. Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense. 3. Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap 4. Sealant will fully cure in 72 hours Limitations: • Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. • Sealant is not paintable.Complete painting 7days prior to applying sealant. • Not for aquariums or contact with food, eating utensils or drinking water.
$21.37
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$19.12
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$9.00
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$5.00
![Selleys No More Gaps Timber Floors x 380g [Walnut]](http://gluesaustralia.com.au/cdn/shop/files/169e8e96732544d89fdb6ec6deaba129.jpg?v=1757753052&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
![Selleys No More Gaps Timber Floors x 380g [Jarrah]](http://gluesaustralia.com.au/cdn/shop/files/42b566f39b234ffeab320faed408b86e.jpg?v=1757753057&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
![Selleys No More Gaps Timber Floors x 380g [Hardwood]](http://gluesaustralia.com.au/cdn/shop/files/5160e944b5d3493cbac2a999232381fa.jpg?v=1757753063&width=645)
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required. Features Superior flexibility and stretch capability to cope with movement Truly sandable to give a smooth clean finish. Contains real wood fibre allowing the filler to receive stains better than standard gap fillers Filler provides an airtight seal, keeping out draughts, dust and pests. Easy water clean up Where can this product be used? For filling and sealing gaps around and between tongue and groove timber floors. Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves. What materials is this product suitable for? Timber floors Timber match: Jarrah - Jarrah, River Red Gum, Karri Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech Walnut - Ironbark, Teak, Dark stained timbers and engineered floors Baltic - Pine, Myrtle, Alpine Ash Size 380g Cartridge Technology Water-Based Use Interior How to Use: The surface to be filled must be clean, dry and free from dust. Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun. Apply with a caulking gun, forcing product into the gap. Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary. Clean up with a damp cloth immediately. Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive. Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary. Limitations: Not for exterior use. Not for gaps greater than 3mm wide in trafficable joints. Tips: Ensure sufficient product is applied into the gap if filling tongue and groove overlaps Coverage: 18 m / 3mm bead Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
$15.00
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$11.00
Selleys Liquid Nails Exterior: The Builder's Choice for Durable Outdoor Bonds Key Features Adheres up to 3 tonnes per m² after just 4 hours on timber Water, heat, and UV-resistant Long-lasting bond that won't crack or go brittle Fast and easy water clean-up Compliant with Australian Standard AS 2329(1999) and Green Building Council VOC limits Suitable Materials This adhesive is ideal for the following materials: Timber Plasterboard MDF LOSP Treated Timber Concrete Masonry Plastics (pre-test for compatibility) Tiles Glass Ceramics Directions for Use Follow these simple steps for optimal performance: Ensure surfaces are clean and free from grease or loose particles. Cut cartridge tip, fit nozzle, and cut to 5mm opening. Apply adhesive along the material's length or in beads on flat surfaces. Press pieces firmly together, securing with fasteners or clamps. Allow to set for a minimum of 4 hours before removing any temporary fasteners. Limitations Not suitable for use on PFTE, PE, or PP. Cleaning & Safety Clean up is easy with warm soapy water or a damp cloth for wet adhesive, and a scraper or sandpaper for dried adhesive. Product Specifications Available in 350g cartridges, in white color, and uses Self-crosslinking acrylic technology.
$12.00
Selleys KwikGrip Spray 350g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces Adhesive Mastery: Quick, Clear & Heat Resistant Discover the power of Selleys KwikGrip Spray 350g, a versatile adhesive spray that bonds instantly on contact. Ideal for both absorbent and non-absorbent surfaces, it offers a quick-drying and heat-resistant solution for a multitude of projects. Key Features: Versatile adhesive spray Durable bond Fast drying and dries clear Heat resistance up to 70°C Common Applications: Car upholstery repairs Fixing laminate on tables and bench tops Patching vinyl flooring Art and craft projects And many more... Compatible Materials: Laminated plastics Timber Craft foam Aluminium Leather Canvas Rubber Most plastics* How to Use: USE ONLY IN A WELL VENTILATED AREA. Shake the can well. Ensure surfaces are clean and dry. Hold the can 20cm away and spray surfaces evenly. For a permanent bond, spray both surfaces and wait until touch dry before pressing together. Clamp overnight for a firm bond. For a temporary bond, spray one surface and press together while still tacky. Limitations: Not suitable for bonding rough, ill-fitting surfaces or certain plastics like polyethylene or polypropylene. Refer to the guidelines for alternative solutions. Handy Tips: After use, clean the nozzle by inverting the can and spraying until clear
$21.00
Selleys KwikGrip Spray 150g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces Adhesive Mastery: Quick, Clear & Heat Resistant Discover the power of Selleys KwikGrip Spray 150g, a versatile adhesive spray that bonds instantly on contact. Ideal for both absorbent and non-absorbent surfaces, it offers a quick-drying and heat-resistant solution for a multitude of projects. Key Features: Versatile adhesive spray Durable bond Fast drying and dries clear Heat resistance up to 70°C Common Applications: Car upholstery repairs Fixing laminate on tables and bench tops Patching vinyl flooring Art and craft projects And many more... Compatible Materials: Laminated plastics Timber Craft foam Aluminium Leather Canvas Rubber Most plastics* How to Use: USE ONLY IN A WELL VENTILATED AREA. Shake the can well. Ensure surfaces are clean and dry. Hold the can 20cm away and spray surfaces evenly. For a permanent bond, spray both surfaces and wait until touch dry before pressing together. Clamp overnight for a firm bond. For a temporary bond, spray one surface and press together while still tacky. Limitations: Not suitable for bonding rough, ill-fitting surfaces or certain plastics like polyethylene or polypropylene. Refer to the guidelines for alternative solutions. Handy Tips: After use, clean the nozzle by inverting the can and spraying until clear
$11.00
Selleys Kwik Grip High Temp Spray: Heat & Water Resistant Adhesive for Extreme Conditions Bond Like a Pro: From Marine Carpets to Car Interiors Presenting Selleys Kwik Grip High Temp Spray, a premium adhesive formulated to withstand extreme heat up to 90 degrees and resist salt water. Ideal for tasks requiring high-grade adhesion, from car headlining repairs to marine carpet installations. Key Features: Heat resistant up to 90 degrees Water and salt water resistant Fast drying High grab Applications Include: Repairing headlining in cars Adhering marine carpets in boats Suitable Materials: Wood Metal Aluminium Fabric Polyurethane foam Laminate Leather Felt Cork How to Use: Clean and dry the surface before application. Shake the can well and hold it 20cm away from the surface. Spray both surfaces liberally. Wait for up to 5-10 minutes for the adhesive to become touch dry. Align and press the surfaces together, applying
$25.00
A solvent-based, heat resistant, flexible contact adhesive suitable for bonding both absorbent and non-absorbent surfaces. It forms an instant bond on contact of two surfaces. The gel form allows application without dripping or ‘stringing’. Great for vertical surfaces. Features Heat resistance up to 130C No clamping required Suitable for interior and exterior jobs Cured adhesive is resistant to dilute acids and alkalis Immediate set on contact. Maximum strength after 24 hours Gel Grip has a thicker consistency than Kwik Grip and so is ideal for vertical applications as it won’t run Gel form prevents running or stringing Easy to spread by brush and ideal for use on vertical surfaces Where can this product be used? Vertical surfaces where dripping and running is a concern Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench or table tops Areas where clamping or pressing facilities are either not available or difficult to use Patching vinyl Flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Fixing laminate to tables, benchtops etc Repairing canvas tents and outdoor equipment Bonding metal or laminate sheeting Replacing trim, rubbers and weather seals in cars Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers etc Some plastics such as vinyl sheeting and polystyrene are attacked by Gel Grip. Test in an inconspicuous area prior to application. Can cause discolouration and bubbling when used for vinyl flooring materials, seek the advice of flooring material manufacturer before using Gel Grip. We recommend Kwik Grip Advanced for these applications Contains highly flammable solvent and care should be taken to ensure all fire precautions are observed. Cannot be used for application in temperatures below 10oC. Suitable for porous materials but not for rough, ill-fitting surfaces. (Consider the suitability of alternative products such as Liquid Nails for rough ill-fitting surfaces). What materials is this product suitable for? Cork Rubber Felt Canvas Leather Metals Timber Laminated plastics (laminex, formica) Hardboard Compressed board How to use this product Ensure that surfaces to be bonded are clean, dry and free from grease or paint. Cut laminated plastic sheet slightly oversize all round. Completely cover both surfaces with adhesive and keep apart until touch dry – no more than 40 minutes. Position the items carefully, still keeping surfaces apart with dowels or heavy craft paper and working from one edge press surfaces firmly together. Secure bond by running a roller over the bonded surfaces or else by hammering the surface from the centre outwards using a padded block. For bonding other materials, apply as for laminated plastics above. When small surface areas are to be joined a wet bond may be used. Simply apply Gel Grip to one surface then bring the surfaces together and clamp until dry. Handy tips Care should be taken to test plastics prior to use as solvents present will attack some grades such as polystyrene and sheet vinyl. Use Kwik Grip Advanced for these applications. Keep container sealed when not in use. Coverage – up to 5 square metres/litre (bonded area 2.5 square metres/litre) depending on porosity of surfaces and thickness of applications For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Clean Up While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Gel Grip has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent. Safety tips Ensure thorough ventilation when using. Avoid using in a confined space for prolonged periods. Use Kwik Grip Advanced as a low fume alternative. Avoid skin contact as solvents in Gel Grip have a degreasing effect and may result in irritation. If in eyes flush with plenty of water for 15 minutes. Seek medical advice. If poisoning occurs, contact a doctor or Poisons Information Centre. Phone Australia 131 126 or New Zealand 0800 764 766. If swallowed, do not induce vomiting. Give a glass of water. Highly flammable. Do not use in the same area as flame, fire or spark producing apparatus or machinery. This product should NOT be accessible to juveniles, because of its solvent content. For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use Clean Up While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Gel Grip has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent. Store in a cool area away from ignition sources and out of direct sunlight.
$8.00
![Scotch 3M Mount Double Sided Squares Indoor 15lb x 48 [2.54cm x 2.54cm]](http://gluesaustralia.com.au/cdn/shop/files/051131769960N_f18dde17-9448-4437-aace-df5695c465e8.jpg?v=1754711993&width=645)
Scotch Indoor Double-Sided Mounting Squares are ideal for painted surfaces and allow you to quickly and easily beautify and organize your space. Whether you’re creating a gallery wall or affixing the family chore chart, these permanent double-sided foam squares hold up to 15 pounds and deliver a strong bond every time because of their 3M™ industrial strength adhesive. Your work is up and ready to admire in 30 seconds flat – no nails or hammer needed. Never let how you’re going to hang it get in the way of your creativity with the powerful adhesion of Scotch Indoor Double- Sided Mounting Squares. Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 3 squares To hold 15 lb use 45 squares Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in the USA with Globally Sourced Materials Color: White Specifications Size (Imperial) 0.5 in x 0.5 in, 1 in x 1 in
$8.89
Prep Marathon Sugar Soap for Walls and Floors cleans dirt, grease, and grime from all types of flooring. Remove soap scum from showers with ease on mirror shower doors. The multi-use formula means one product can do more than just one job!
$4.28
Heavy-duty liquid cleaner removes dirt, grease and general grime. Leaving floor and wall surfaces in optimum condition.
$9.00
Parfix Maxi Nails 300g: The Ultimate Multi-Surface Construction Adhesive Key Features High-strength bond suitable for a variety of applications Paintable for aesthetic versatility Effective both indoors and outdoors Specifications Colour: Beige Model Name: Parfix 300g Maxi Nails Construction Adhesive Material: Polymer Dissolved in Hydrocarbon Solvent Outdoor: Yes Indoor: Yes Why Choose Parfix Maxi Nails 300g? Designed to handle a multitude of construction challenges, Parfix Maxi Nails 300g provides a robust bond that lasts. Whether you're working indoors or taking on external projects, this adhesive is formulated to give you the results you need.
$4.19
Parfix Fast Grip is a solvent-based contact adhesive that is heat and water-resistant, making it suitable for use in kitchens and bathrooms. Immediate strong bond Heat and water resistant Brush application
$18.00
This product is a quality PVA glue suitable for general woodworking. It is non-toxic, will not stain timber and dries clear. Suitable for Wood, Particle Board, Unglazed Pottery, Laminating, veneers, paper, cardboard, leather, foam and cloth Directions: Ensure all surfaces are clean, dry and free of oil, grease and wax Shake well before use Only apply to one surface Press surfaces together while the adhesive is still wet and clamp lightly (approx 2 to 4 hours in normal conditions) Remove excess glue with a damp cloth Great strength is achieved when dried overnight Cleaning: Clean up with water. Wash hands after use
$44.11
Neoprene solvent-based contact cement gel used for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding. LOCTITE® MR 5412 is a yellow, neoprene solvent-based contact cement gel used for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding. Typical applications include bonding weather stripping, insulation, rubber and trim to wood and metal. Suitable for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding Technical Information % Solids 10 Agency Approvals / Specifications CFIA Listed Colour Yellow Fixture Time 15 min. Key Characteristics Waterproof Physical Form Liquid Specific Gravity 0.88 g/l Specific Gravity Temperature 25 °C Substrates Metal, Wood Directions for use: 1. Clean surfaces thoroughly. Use abrasives to remove any powdery mold release from new weatherstripping. 2. Apply a thin, even film to both surfaces. 3. Allow to dry tacky (3 to 4 minutes). 4. Bond the two surfaces together and apply enough pressure to produce uniform contact. 5. NOTE: The early strength of LOCTITE® MR 5412 is enough to hold most parts together. However, maximum strength is obtained after the adhesive is completely dry. Aging of the bond and exposure to moderate heat increases strength.
$16.45
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
$13.11
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
$40.93
A heat resistant, solvent-based, flexible contact adhesive suitable for bonding both absorbent and non-absorbent surfaces. It forms an instant bond on contact of two surfaces. Features; Heat resistance up to 130C No clamping required Suitable for interior and exterior jobs Cured adhesive is resistant to dilute acids and alkalis Grabs immediately on contact Easy to spread Appearance: Yellowish to beige coloured opaque liquid with strong solvent odour. Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench or table tops Areas where clamping or pressing facilities are either not available or difficult to use Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Fixing shoes Fixing laminate to tables, benchtops etc Leather shoe and leather repairs, leather work eg handbags Repairing tents and outdoor equipment Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Attaching rubbers to your fridge door Repairing your wetsuit Some plastics such as vinyl sheeting and polystyrene are attacked by Kwik Grip Solvent. Test in an inconspicuous area prior to application. Seek the advice of vinyl flooring manufacturers prior to use with their products as discolouration and bubbling can occur with some types. If in doubt, Kwik Grip Advanced is safe to use for all these applications and will provide excellent bonding. Contains highly flammable solvents and care should be taken to ensure all fire precautions are observed. As an alternative, Kwik Grip Advanced is non-flammable. Not suitable for bonding rough, ill-fitting surfaces. (Consider the suitability of alternative products such as Liquid Nails for these applications). What materials is this product suitable for? Cork Rubber Felt Canvas Leather Metals Timber Laminated plastics (laminex, formica) Hardboard Compressed board How to use this product: When bonding laminated plastics, ensure that surfaces to be bonded are clean, dry and free from grease or paint. Surfaces to be bonded should be relatively smooth and/or close fitting. Both surfaces should be completely covered with adhesive and kept apart till “touch dry” – no more than 40 minutes. Position the items carefully, still keeping surfaces apart. Remember once joined they cannot be repositioned. When edges are perfectly aligned, press surfaces firmly together. Secure bond by running a roller over the bonded surfaces or else by hammering the surface from the centre outwards using a padded block. For bonding other materials, apply as for laminated plastics above. When small surface areas are to be joined a wet bond may be used. Simply apply Kwik Grip Solvent to one surface then bring the surfaces together and clamp until dry. Handy tips: -Care should be taken to test plastics prior to use as solvents present will attack some polystyrene and sheet vinyls. -Up to 5sq.m/litre (bonded area 2.5sq.m/litre) depending on the porosity of surfaces. -For vertical surfaces, we recommend using SELLEYS Kwik Grip Gel Vertical. -For applications in confined or low ventilation areas eg car interior, we recommend using SELLEYS Kwik Grip Waterbased, as it is non-toxic and free of fumes. -Use a brush, knife or serrated scraper for application. -When using the contact method REMEMBER bonding is immediate once the two surfaces are joined. -Keep container sealed when not in use. -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. -While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Kwik Grip Horizontal has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent. -Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips: -Ensure thorough ventilation when using. Avoid using in a confined space for prolonged periods. We recommend you use Kwik Grip Waterbased in these circumstances. -Highly flammable. Do NOT use in the same area as flame, fire or spark producing apparatus or machinery. -This product should not be accessible to juveniles, because of its solvent content. Intentional misuse by deliberately inhaling vapours from this product can be harmful or fatal. -Contact with skin and eyes should be avoided and avoid breathing vapour. -If in eyes flush with plenty of water for 15 minutes and seek medical advice. -If poisoning occurs, contact a doctor or Poisons Information Centre. Phone Australia 131 126 or New Zealand 0800 764 766. If swallowed, do NOT induce vomiting. Give a glass of water and seek medical advice. -For further information refer to the Safety Data Sheet (MSDS). Storage and re-use Store in a cool area away from ignition sources and out of direct sunlight.
$7.00
Selleys Kwik Grip Crystal Clear applies clear and dries crystal clear for less mess and invisible bond lines. Excellent for achieving a neat, clear finish when bonding large, flat close-fitting surfaces eg veneers and laminates for bench or table tops. Forms a durable, heat and water-resistant bond. Features: Solvent based contact adhesive Applies clear and dries crystal clear Strong, durable bond on broad surfaces Easy to spread Heat resistant – up to 80°C Water resistant Where can this product be used? Applications where invisible bond lines are needed such as adhering decorative strips to a mirror Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench or table tops Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Fixing shoes Fixing laminate to tables, benchtops etc Leather shoe and leather repairs, leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Seek advice of vinyl flooring manufacturers prior to use with their products as discolouration and bubbling can occur with some types. If in doubt, Kwik Grip Waterbased is safe to use for all these applications and will provide excellent bonding. Not suitable for bonding rough, ill-fitting surfaces. (Consider the suitability of alternative products such as Liquid Nails for these applications). What materials is this product suitable for? Veneers Rubber Cork Felt Leather Canvas Metals Timber How to use this product USE ONLY IN A WELL VENTILATED AREA Contact Bonding Hold down lid, whilst opening can. Ensure surfaces are clean and dry. If cutting laminate sheets, cut slightly oversize. For porous surfaces apply a thin coat to seal surface and allow to dry for approx. 40mins. Using applicator, completely cover both surfaces with adhesive and keep surfaces apart until ‘touch dry’ – approx 15 minutes, no more than 30 minutes. Position items carefully, still keeping surfaces apart with dowels. When edges are perfectly aligned, remove dowels, and working from one edge, press surfaces firmly together. Grabs IMMEDIATELY on contact. Secure the bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum bond strength is reached after 24 hours. Clamping of warped or curled surfaces may be necessary. Wet Bonding (For small areas or for bonding where one surface is porous) Ensure surfaces are clean and dry. Apply KWIK GRIP to one surface, then bring the surfaces together and clamp until dry. Handy tips Care should be taken to test plastics prior to use as solvents present will attack some polystyrene and sheet vinyls. Cover: 500mL covers up to 2.5m2 of one surface, depending on porosity of surfaces. For vertical surfaces we recommend using SELLEYS Kwik Grip Vertical Gel. For applications in confined or low ventilation areas eg car interior, we recommend using SELLEYS Kwik Grip Waterbased, as it is non-toxic and free of fumes. Use a brush, knife or serrated scraper for application. When using the contact method REMEMBER bonding is immediate once the two surfaces are joined. Keep container sealed when not in use. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Kwik Grip Crystal Clear has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Contains highly flammable solvents and care should be taken to ensure all fire precautions are observed. As an alternative, Kwik Grip Waterbased is non-flammable.
$11.00
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$21.72
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.90
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.00
Introducing Gorilla Clear Grip® - Your Ultimate Adhesive Solution! Are you tired of struggling with weak bonds that don't stand the test of time? Say goodbye to ordinary adhesives and embrace the power of Gorilla Clear Grip® - the flexible, fast-setting, and crystal clear contact adhesive that creates an unbreakable bond! Unleash your creativity with Gorilla Clear Grip®! Whether you're building, repairing, or crafting, this heavy-duty adhesive is your go-to companion. Its no-run formula ensures a clean and easy application, while the fast grab feature holds your project in place within seconds, saving you precious time and effort. Worried about the unpredictable weather? Fear not! Gorilla Clear Grip® is fully waterproof, making it ideal for both indoor and outdoor projects. Rain or shine, your creations will stay intact and look flawless for years to come. What sets Gorilla Clear Grip® apart is its remarkable versatility. It forms a permanent bond on a wide range of materials, including metal, glass, fabric, wood, ceramic, leather, paper, plastic, and more. With Gorilla Clear Grip®, you can confidently tackle any project, big or small. Concerned about safety? Worry not! Gorilla Clear Grip® is photo-safe and washer/dryer safe, ensuring that your precious memories and fabrics remain unharmed during the bonding process. Using Gorilla Clear Grip® is a breeze! Just ensure that the surfaces are clean and apply the adhesive to each surface to be bonded. For maximum bond strength, wait a couple of minutes for the adhesive to partially dry before joining the surfaces. The bond forms immediately, ensuring a strong connection. Store your Gorilla Clear Grip® in a cool, dry location after each use, away from children and animals. The flammable adhesive requires extra care, so keep it away from heat, sparks, flames, or smoking. For easy re-opening, apply a thin coat of petroleum jelly to the threads before replacing the cap. Frequently Asked Questions: Q: What surfaces does Gorilla Clear Grip® adhere to? A: Gorilla Clear Grip® adheres to a wide variety of surfaces, including wood, metal, stone, ceramic, glass, plastic, PVC, brick, concrete, foam, paper, rubber, fabric, and laminate. However, it is not recommended for use on polystyrene, polypropylene, or polyethylene products, and it should not be used around food. Q: How do you clean up Gorilla Clear Grip®? A: To clean uncured adhesive, wipe it with a dry cloth and then use acetone, isopropyl alcohol, or citrus-based solvents according to the manufacturer's instructions. Cured adhesive can be removed by scraping it from the surface. Q: Is Gorilla Clear Grip® UV resistant? A: Yes, it is UV resistant, making it ideal for outdoor applications. Experience the Gorilla Clear Grip® difference today! Unleash your creativity, achieve impeccable results, and make your projects stand the test of time. Join the countless satisfied customers who have discovered the power of Gorilla Clear Grip®. Build, Repair, Craft™ with confidence!
$15.97
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. Features: CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More Directions All surfaces must be clean and tight fitting. Clear Gorilla Glue will stain clothes. 1. Damp It For non-porous surfaces only (i.e. metal, glass, plastics), lightly dampen one surface with water. Do not add water to the bottle. 2. Glue It Apply Clear Gorilla Glue to surfaces. Best at room temperature. 3. Clamp-It Clamp objects together for 2 hours. Full cure in 24 hrs. You can use heavy objects to achieve clamping pressure. *Not recommended for use on polyethylene or polypropylene plastics. Storage Tips After each use, wipe nozzle clean with a dry cloth and tightly replace lid. Store in a cool, dry place with exposure to light. Lack of light and heat can cause the product to yellow. Cured glue can be removed from work surface with chisel, scraper or sandpaper. Store away from children and animals. Specs: APPLICATION TEMPERATURE – 32° to 100° F, best at room temperature SERVICE TEMPERATURE – -20° to 180° F OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – No FAQS What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight-fitting joints. It’s perfect for a fix you need doing fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also gap filling which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant and can withstand intermittent exposures, however, is not meant for a constant soak. Original or White Gorilla Glue is 100% waterproof and can withstand soaking and longer-term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$22.51
Advanced Strength Dots™ Dot N Go® fits in the palm of your hand and is perfect for quick fixes and repairs. With a small footprint, the Advanced Strength Dot N Go stores easily in a toolbox or drawer for easy access. Ideal for tough jobs and DIY projects that require exceptional holding power. Not recommended for temporary applications or delicate items. Glue Strength - Super-Strength (Holds up to 8 lbs.) Features/Benefits: Hand-held Dispenser | Easy to Use Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free Adhesive Size: 3/8 in. diameter Adhesive Color: Amber Quantity: 125 Adhesives
$8.95
Glue Dots® Advanced Strength Double-Sided Sheets can be custom cut to any size or shape to provide adhesive coverage for projects both big and small. Ideal for tough jobs and DIY projects that require exceptional holding power. Not recommended for temporary applications or delicate items. Glue Strength - Super-Strength (Holds up to 8 lbs.) Features/Benefits: Resealable Bag | Easy to Store Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$7.98
Craft Glue Dots® are versatile, permanent adhesives ideal for heavier materials like wood or metal, large embellishments or thick cardstock. Glue Strength - Super-Strength Features/Benefits: Hand-held Dispenser | Easy to Use Acid Free| Photo Safe Non Toxic | Kid Friendly Specifications Adhesive Size: 3/8 in. diameter Adhesive Color: Clear Quantity: 200 Adhesives
$12.74
*NEW* Fix-A-Floor Polyurethane Wood Floor Repair Adhesive is an Extra Strength, Super Blend Formula! Created specifically for Re-Bonding those Loose & Hollow, Squeaky, Popping, Bouncy Wood Floors. No need to remove or replace, Just Drill & Fill! The narrow tip allows for the smallest holes to be drilled leaving an undetectable permanent repair. Works on all Hardwoods, Engineered Wood & Bamboo Floors. Good for Indoors & Outdoors, Small or Large problem areas. Odorless, Very Low VOC’s. Coverage: One 10.1 oz. Fix-A-Floor Repair Adhesive Tube covers approximately 2 ft. x 2 ft. (4 sq. ft.). Just Drill & Fill Flooring Professionals prefer a polyurethane when fixing wood floors. The super blend polyurethane properties of the Fix-A-Floor adhesive will not foam or expand when applied and dries in 24 hrs. The adhesive when dry will move with the natural expansion and contraction of the sub floor below ensuring it will never dry and crack and lose its bond. Finally fix those loose, squeaky, bouncy wood floors forever. The Original Fix-A-Floor is good for wood flooring repair for smaller spot fixing, we recommend the Fix-A-Floor Polyurethane for small and larger wood flooring applications. Not recommended for use in moist or wet areas. The Fix-A-Floor Large Application Syringe is another fantastic way to apply Fix-A-Floor if you wish to drill an even smaller hole than 9/64" to fix those loose, squeaky, bouncy wood floors. Always test in a small area first to ensure desired results. Keep from freezing before use. Directions for Fixing Wood Floors: 1.Locate problem areas by tapping with wooden dowel, broom handle or similar, mark perimeter with chalk or painters’ tape. 2.Inside the marked area use a 9/64" drill bit and drill at least 1 hole on each end of problem floorboard(s), larger areas may require additional holes. Vacuum over each hole to clear debris. 3.Pull cap off tip and unscrew the tip to pierce a large hole using an awl or similar into the top of the threaded tube. If needed poke hole with awl through tip to clear, screw tip back on tube. 4.Using a quality caulk gun begin filling Fix-A-Floor into each drilled hole. Once adhesive spills up and out of nearby hole(s) this ensures complete coverage. Place finger over tip to avoid spillage when moving between holes. 5.Once filled, wipe clean with damp rag/sponge, and allow to cure for 24 hours before filling holes. Visit your local flooring/home improvement store to locate matching wood putty/filler and fill holes. For any excess residue please use mineral spirits to wipe clean. Your Floor is FIXED!
$44.95
Dunlop Revive & Shine Dunlop Revive & Shine is a neutral, multipurpose cleaner and maintainer that enhances the appearance of sealed floors. Designed for use on timber, vinyl, and laminate floors, this product reduces the appearance of scuffing, increases durability, and improves gloss levels. For best results, use monthly to keep your floors looking their best. Key Benefits: Cleans and maintains timber, vinyl, and laminate flooring Provides extra durability, wear resistance, and shine Increases slip resistance Reduces the appearance of scuffing Ideal for monthly maintenance Suitable For Use On: Timber, vinyl, and laminate flooring Surface Type: Floors Location: Indoor Colour & Sizes: Colour: Milky (Dries Clear) Size: 500ml Item Code: 19882 Directions for Use: Dilution: Mix 20mL of Dunlop Revive & Shine per 1L of warm water in a bucket. Cleaning: Mop the floor with the solution. Spills: For spills, hose down the area and wash with large amounts of water. Note: The use of Personal Protective Equipment is recommended during application. Dunlop Revive & Shine is perfect for keeping your timber, vinyl, and laminate floors looking like new, providing enhanced shine, durability, and slip resistance.
$21.46
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$12.44
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$8.70
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$7.72
You have seen 48 out of 97 products
Bonds and sealants suited to laminate sheets, benchtops and panels. Contact adhesives remain the go-to for large surface areas; select high-heat grades for kitchens and verify open time for proper tack. For trims or repairs, consider fast-set options and tapes where clamping is difficult. Surface must be clean, dry and de-greased. Use the filters to narrow by chemistry, cure speed, temperature rating and clean-up. Always check the product page and TDS/SDS for suitability and instructions.
