Davco PrimeX Multipurpose Acrylic Primer 5L is a professional-grade, water-based primer specially formulated to improve the adhesion of tile adhesives and waterproofing membranes to porous surfaces. Ideal for interior and exterior walls and floors in domestic and commercial applications, this primer ensures strong bonding performance while reducing porosity and dusting of substrates. Surface Preparation: Surfaces must be clean, dry, and free from dust, oil, grease, wax, paint, curing compounds, and other contaminants. Remove any laitance, loose materials, or previous coatings that may interfere with adhesion. On hot or windy days, dampen porous substrates lightly to avoid flash drying—but do not leave standing water. Application Instructions: Stir the primer thoroughly before use. Apply evenly using a roller, brush, broom, or squeegee in a thin, consistent layer. Allow the primer to dry fully before proceeding—drying is complete when the white, milky appearance turns clear. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Typically dries within 30–60 minutes under standard conditions. Cooler temperatures or high humidity may extend drying time. Clean Up: Clean tools and equipment with water immediately after use. Do not allow the product to dry on tools. Technical Data: Type: Acrylic-based Colour: Milky white (dries clear) Suitable for: Cement render, concrete, fibre cement sheets VOC Content: Low Packaging: 5 Litre plastic container
$88.36
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$5.75
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$6.59
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$6.11
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$15.00
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$12.11
Bostik HG3 Hot Melt Glue Gun is an electric hot melt gun that uses Bostik HG3 Hot Melt Glue Sticks to provide an instant, fast, clean and versatile adhesion to a myriad of household and craft materials. It is rated 110-240 volts, 50/60Hz, 55 watts with a working temperature of 193°C. Recommended Uses Ideal for: Craft projects Home décor projects Minor household repairs DIY projects Most craft and household materials Fabric Wood Leather Most plastics Polystyrene Ceramics Key Features: Easy to use trigger action Designed to fit neatly in the hand Designed for use with Bostik HG3 Glue Sticks Uses: Bostik HG3 Glue Gun, using Bostik HG3 Glue glue sticks provide an instant fast, clean and versatile adhesion to a myriad of household and craft materials. - Bostik HG3 Glue Gun is designed for DIY Tasks and household repairs, hobby, craft-work, and home décor projects. Instantly bonds most craft and household materials including, fabric, wood, leather, most plastics, ceramics and metal Application: 1. Clip metal stand on the glue gun. Always use the stand. Never lie gun down on the side when in use or whilst cooling down this will cause gun failure. 2. Insert Bostik HG3 glue stick gently through the tunnel at the back of the gun. Never use excessive force as the glue stick will clog the channel. 3. Plug the cord into an electrical outlet and wait 5 minutes to heat up the glue. Ensure glue is hot or glue will not extrude through the gun. 4. Apply adhesive by gentle continuous pressure and to the more difficult surface to bond (usually smooth surfaces are more difficult to adhere than rough, porous surfaces). 5. Release trigger to stop the flow of glue. 6. Glue does not need to be spread. Do not touch 7. Molten adhesive, as temperatures around 200°C will cause serious burns. 8. Join surfaces as quickly as possible for optimum bond strength. 9. To bond foam products (polystyrene foam etc) to another surface, apply adhesive in an “S” pattern to the surface to which the foam will be bonded, rather than directly to the foam. 10. To bond fabrics, use a smaller “S” pattern for additional strength. 11. Small drops of glue can be easily removed when cold. 12. Residual glue can be remelted and removed from most bonded surfaces with a warm knife. 13. When you have finished using the gun, switch off and unplug it. 14. Allow the glue stick to remain in the gun – do not remove the stick from the rear of the gun at any time
$23.14
Betta TileCare Tile & Grout Cleaner is a powerful, ready-to-use solution designed to effectively remove ingrained dirt, grease, grime, and oil deposits from tiled surfaces without causing damage. Its fast-acting, biodegradable, and non-caustic formula makes it both user-friendly and environmentally responsible. Surface Preparation: Ensure the surface is free from dust and loose materials before cleaning. Application Instructions: Spray Betta TileCare Tile & Grout Cleaner directly onto the affected area. Vigorously scrub the area with a stiff brush to lift dirt and grime. For heavily soiled surfaces, repeat the application as necessary until the stain is removed. Coverage: Approximately 3 to 4 square meters per liter. Drying Time: Allow the cleaned area to dry completely before use. Cleanup: After scrubbing, leave the solution on the surface for 5 to 10 minutes, then rinse thoroughly with water. Do not allow the cleaner to fully dry before rinsing. Technical Data: Appearance: Clear liquid pH Level: Neutral Solubility: Fully water-soluble
$29.75
Product Overview: Bastion Multipurpose Primer is a professional-grade waterproofing primer designed for wet areas and tiled surfaces. It enhances adhesion for waterproofing membranes, adhesives, and coatings, making it ideal for use in bathrooms, kitchens, balconies, and other areas exposed to moisture. It is compatible with most construction adhesives and offers rapid drying for faster project completion. Features & Benefits: ✔️ Multipurpose Use – Suitable for internal & external applications on walls and floors ✔️ Enhances Adhesion – Ensures strong bonding for tiles and waterproof membranes ✔️ Rapid Drying – Reduces wait times and speeds up installation ✔️ Low VOC Formula – Environmentally friendly with minimal odour ✔️ High Coverage – Approx. 5m² per litre for cost-effective application Surface Preparation: Ensure surfaces are clean, dry, and free from dust, grease, and other contaminants. Remove loose particles and repair any cracks before application. Porous surfaces may require multiple coats for optimal adhesion. Application Instructions: Shake well before use. Apply using a brush, roller, or spray for even coverage. Allow to dry for approximately 30 minutes before applying waterproofing membranes or adhesives. For highly absorbent surfaces, apply a second coat after the first has dried. Coverage: 1L covers approx. 5m² (depending on surface porosity and application method). Drying Time: Touch dry: 15-30 minutes Ready for membrane or adhesive application: 30-60 minutes Clean-Up: Clean tools immediately with warm, soapy water before the primer dries. Dispose of residue according to local waste disposal regulations. Technical Data: Type: Acrylic-based primer Colour: Milky white (dries clear) VOC Content: Low Application Temperature: +10°C to +35°C Storage: Store in a cool, dry place away from direct sunlight Safety Warnings: Avoid contact with skin and eyes; wear protective gloves and eyewear. Use in a well-ventilated area to prevent inhalation of fumes. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for detailed handling information.
$55.00
You have seen 105 out of 105 products
Primers, activators, mixing nozzles, applicators and kits that complete your bonding or sealing system. Improve adhesion, speed and accuracy for pro‑quality results. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
