Industrial grade PVA, especially developed for use by professional woodworkers and craftsmen, for large projects. Off-white in colour, drying to a light coloured clear film. Features Excellent performance properties for repairs or building projects No mixing required Suitable for exterior use in non-structural applications Heat resistant to 110°C (bonds will not weaken in exposure to direct summer sun) Can be chiselled, routed or turned Suitable for end grain gluing – won’t stain timber, cream in colour, but dries clear with a slight yellow tint Non-toxic Sandable – will not clog sandpaper like other PVA emulsion glues More water resistant than Aquadhere interior Has a higher heat resistance than Aquadhere interior Paintable Provides a stronger bond than Aquadhere interior for larger jobs Bonds MDF Weather resistant Cleans up with water Where can this product be used? Cabinet and furniture making Timber letterbox Making a bookshelf Restoring furniture Gluing cupboard shelves for additional support Repairing a door frame or window Repairing or building wooden outdoor furniture Indoor furniture Storage chest for tools Pot plant stand Dog kennel Bed heads Timber joinery Wooden toys Unsuitable for use on coated wallpaper overlaps eg vinyl Will not take common timber stains Not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue Not suitable for below waterline applications or continuous submersion. We recommend Selleys Knead It Aqua for these situations. What materials is this product suitable for? Softwoods Plywood Joinery Hardwoods MDF Laminating Particleboard Dowelling Veneering Chipboard How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Cure slows significantly in humid, cold conditions. Handy tips 1L covers approx. 5m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use 308 High Stress Wood Glue. Avoid contaminating Aquadhere Exterior with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. Painting or varnishing constructions made of porous softwoods will improve the resistance of bonds to water exposure. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of Selleys Hand Kleen Wipes nearby for a quick and effective cleanup.
$15.00
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding Features Super Durable High Strength 100% waterproof* – *(not for permanent water immersion) Bonds wood to almost anything Acid & chemical Resistant – PVA’s break down with acid/alkaline contact Versatile can be used to bond surfaces other than wood Heat resistant up to 140 deg Generous working time (10 minutes) Expands as it dries Sandable – easy, will not clog sandpaper like other PVA emulsion glues Paintable Stainable after sanding The product is a brown liquid and turns a light yellow when fully cured Can be used for gap filling Can Also be used to bond surfaces other than wood I.e metal to metal Bonds MDF Non-Toxic (once fully cured) Where can this product be used? Interior and exterior Sauna or cabinet repairs in high heat areas Bonding Timber to other surfaces (metal etc) Cubby House with metal roof & floor lining Planter boxes Steps leading off a verandah Timber letterbox to a metal support frame Window frame Decorative timber to a pergola Interior panels of a boat Repairing wooden boat oars Repairing wooden handles on tools Timber joinery Laminating chopping boards Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice) Cannot be used if application temperature is below 5°C For best results, one surface should be porous Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua Not recommended for structural applications Not recommended for vertical projects due to runny consistency While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming Surfaces should be clamped tightly or weighted What materials is this product suitable for? MDF Glass Metal Concrete Ceramic Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first). All timbers How to use this product Surfaces to be bonded must be close fitting, clean, dust and grease free. Wipe very dry porous surfaces with a damp cloth 1 minute before bonding. Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures. Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured. Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container). Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting. Clean tools with acetone or white turpetine immediatly after use (before adhesive dries). Handy tips 1L covers approx. 8m2 It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin). For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface. The tighter you clamp, the better bond you will obtain (as Durabond expands). Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.) Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive. In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin. If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off. Safety tips Contains organic isocyanate polymers. On contact, uncured adhesive can irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water. Avoid breathing vapours. Ensure use in a well-ventilated area. Product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. Warning: this product contains organic isocyanate polymers. This product has been classified as hazardous according to the criteria of NOHSC and HSNO. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Clean tools with acetone or white spirit immediately after use (before adhesive dried). Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
$28.00
Selleys All Fix Big Jobs is a convenient all-rounder adhesive that sticks just about anything to anything. It provides virtually instant grab on dry porous surfaces eliminating the need for nails and screws on many jobs. It is a heavy-duty adhesive that will bond a wide variety of materials, has low fumes, and conveniently cleans up with water. Features Fast - virtually instant grab on dry porous surfaces eliminates the need for nails and screws on many jobs Fast grab minimises the need for clamping Strong - Heavy-duty adhesive that will bond a wide variety of materials Safe - Low odour, low fumes and non-flammable Dries white and is able to be painted over once dry Lots of working time - bonds can be repositioned within 5-10 minutes Easy to use Fills minor gaps in uneven surfaces (bridges gaps up to 9mm) Strong bond on porous surfaces after 24 hours, cures to maximum strength over a few days Where can this product be used? Re-adhering carpet House numbers to brickwork Wooden furniture repairs Repairing damaged plasterboard Building a dog house Skirting boards Attaching architraves Attaching wall panelling Attaching chair (dado) rails Attaching or building a shelf Use for larger interior projects What materials is this product suitable for? Plasterboard Cabinet Plaster coving Carpet Wood Particleboard Metals (other surface must be porous) Glass (other surface must be porous) Ceramics (other surface must be porous) Brick (other surface must be porous) Concrete Cork Polystyrene foam (other surface must be porous) UPVC (other surface must be porous) Many rigid plastics* (other surface must be porous) Loose wall tiles (in non-wet areas) How to Use Surfaces to be bonded must be dry, sound and free from grease/oil and dust. Work tube between fingers for several seconds to loosen contents. Cut the tip of the nozzle and squeeze to apply adhesive onto one surface. Immediately press parts firmly together. Bonds can be repositioned for up to 5 minutes. If adhesive surfaces form a skin no bond will form. The bond will usually have good strength after 24 hours and will continue to strengthen for a few days. Application Tips For long narrow attachments (e.g. skirting boards) apply one or two continuous beads. For larger flat areas use beads approximately 30cm apart. For small items (e.g. tiles) spots of adhesive may be used. Wipe away excess adhesive with a damp cloth. Dried adhesive is best removed by scraping. Limitations: Not suitable for permanently wet or damp areas. Not suitable for fixing mirrors. Use Selleys Liquid Nails Mirror Metal & Glass. *Not suitable for polyethylene and polypropylene. Use Selleys All Plastic Fix. Bonds are not water-resistant. Protect bonds from water penetration if used in exterior applications. Not resistant to strong acids and strong organic solvents. Do not apply below 10°C. When used near brass or copper, the immediate area of contact will discolour to a blue tone. Handy Tips At least one surface must be porous for effective bonding. If both surfaces are non-porous, drying time is greatly increased. Clamping may be necessary until adhesive dries. Wet, damp and cold weather will increase drying time Wipe away excess with a damp rag. Use temporary supports when bonding a heavy load - support until adhesive dries. Particularly on uneven or smooth or non-porous surfaces. Good for gap filling - i.e. sticking two rough surfaces together. All Fix Big Jobs may stain slightly and colour can be paler than the surrounding area, squeeze out should be wiped off if intending to stain. Clean Up Uncured product may be removed with water. Cured product can be removed by scraping.
$24.32
You have seen 291 out of 291 products
Shop a wide range of bonding solutions for everyday fixes and demanding builds. From instant super glues to heavy‑duty construction adhesives and specialist formulas for plastic, metal, glass, and wood, find the right strength, set time, and finish for your job. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
