![Parfix Roof Gutter Concrete Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115744_c50eb875-361a-40d9-9352-04fade1d8d60.jpg?v=1754712244&width=645)
Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
$11.49
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$14.76
A transparent polyurethane paste adhesive. SuperGrip 30 Minute is a versatile, ready to use, fast curing, general purpose construction adhesive. Uses Bonding of: • Edge bonding of particle board flooring • Timber & MDF • Marble & Stone • Concrete • Block/blocks • Glass • Fibre cement • Tiles • Rubber • Metals • Aluminium Advantages • 100% waterproof (BS-EN204) • Incredibly strong • Bonds almost anything, including LOSP treated timber • Non drip • No shrinkage • Cures in 30 minutes* • Interior and exterior use • High temperature resistance (minus 30ºC to 100ºC) • Cures transparent • Does not stain Technical Data (Typical) Density: 1.12 g/cm³ Solids content: 100% approximately Cure type: Humidity curing Application temperature: 5ºC to 35ºC Service temperature: -30ºC to +100ºC Relocation time: Approximately 5-10 minutes depending on temperature and ventilation. Cure time: Approximately 30 minutes, depending on temperature, moisture content of surfaces and adhesive thickness. Strength will increase over 24 hours. Flammability: Non flammable
$19.00
![Monarch Mini Silicone Mould Resistant [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9320090029073_9b2a79dd-e58b-4fb6-a3b1-d6525871d967.png?v=1754712303&width=645)
Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on! Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours. FEATURES Premium quality 100% silicone Ideal for wet areas Indoor and outdoor use Maximum flexibility BENEFITS Proven to last in all weather Mould resistant Tack free in 10 minutes Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$7.22
Monarch Mini Roof & Gutter Clear Silicone: The Compact Caulking Solution Product Overview Designed for roofing and outdoor applications, the Monarch Mini is perfect for a variety of materials like metal, brick, galvanized iron, tiles, and aluminium. Key Features & Benefits Quick exposure to light running water UV resistant for lasting outdoor use Neutral cure, making it versatile and safe for different materials Non-corrosive and AS 4020 approved Compatible with Monarch Mini Compact Caulking Gun Perfect For Great for small projects where a full-size cartridge is not needed. Ideal for: Repairing gutters Fixing roofs Mending downpipes Tight spaces that traditional cartridges can't reach Colors Available Available in black and translucent versions for versatility in your projects. How To Use Best when used with a Monarch Mini Compact Caulking Gun to reach tight spaces. Always follow the safety guidelines as provided on the product label.
$7.35
Multi-use liquid super glue Water-resistant, dishwasher, shock and temperature resistant Bonds in seconds Strength to withstand heavy loads Dries transparent Product Marketing Has the handle of your favourite mug broken off? Are you looking for a strong glue to mend precious china? Look no further than Loctite Universal Super Glue! This multi-purpose glue helps you to easily handle any kind of small daily repair job around the house! Providing instant strength, transparent drying technology, and an anti-clog cap, Loctite Universal ensures durable, long-lasting, and invisible repairs. This practical, transparent glue works on a variety of materials - from wood, rubber, plastic, and more - it even works as a leather glue. Thanks to its self-piercing anti-clog cap, the repair glue is super easy to use and does not dry out, ensuring long-term reusability. This instant glue not only withstands heavy loads but is also shock-resistant and serves as a waterproof and heatproof glue, proving reliable for a huge range of requirements and uses. When ready to use ensure surfaces to be joined are clean, completely dry, and close-fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$9.95
Loctite Super Glue Longneck Bottle features a precision tip which allows controlled application without dripping, thus less mess. It has an easy-open cap with a metal pin that cleans and seals the nozzle for a clog-free performance. The long nozzle is ideal for gluing hard to reach surfaces. The ''finger friendly'' bottle keeps fingers glue free, as well as allows for a continuous flow or a precise drop of glue. It bonds a variety of materials including leather, ceramic, rubber, paper, metal, china, wood and most plastics. Loctite Super Glue Longneck Bottle dries clear and sets without clamping. Loctite Super Glue Longneck Bottle is resistant to moisture, most chemicals and freezing temperatures. Recommended For Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass™, polycarbonate, polystyrene and PVC Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings Not Recommended For Use in dishwasher, oven or microwave Use on repairs needing high flexibility Glazed surfaces Exterior Applications Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene Safety Precautions Apply in a well-ventilated area. Wear gloves and wash hands after use. Preparation Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup Cured adhesive may be cut away with caution using a sharp blade, acetone or with boiling water.
$8.44
Pressure-sensitive system for easy dosage Non-dripping system to prevent accidental glue run-on Soft, rubber grip for easier handling Bonds in seconds Withstands heavy loads Dries transparent Suitable for use on nearly all materials* Easy to open, self-piercing and anti-clog cap Solvent-free *Except for polyethylene (PE), polypropylene (PP), car glass, Polystyrene foam and synthetic fibres. FEATURES AND BENEFITS Do your repairs with precision and cleanliness with Super Glue Perfect Pen! The new pen-shape device allows a drop by drop application with no mess. It is as easy as writing! Recommended on: Wood, Leather, Rubber, China, Metal, Plastic (except PE/PP). STEP BY STEP Make sure that the surfaces you want to bond are clean, dry and close-fitting To activate pack on first use, screw down the cap clockwise until it stops. Unscrew and remove the cap to apply adhesive. Gently press the rubber panels to apply a small amount of adhesive to one surface only. Press the surfaces together and hold until set Replace the cap immediately and store in a cool, dry place.
$10.50
Loctite® Super Glue Gel has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. The gel formula works on a variety of porous and non-porous surfaces and is ideal for vertical surfaces and small gaps. Loctite® Super Glue Gel comes in a self-piercing tube; it dries clear and sets without clamping. It is also resistant to moisture, most chemicals and freezing temperatures. Recommended For -Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass™, polycarbonate, polystyrene and PVC -Repairing figurines, costume jewelry, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings -Ideal for vertical surfaces Not Recommended For -Exterior applications -Use on repairs needing high flexibility or for gap filling applications -Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene -Glazed surfaces -Use in dishwasher, oven or microwave Safety Precautions: -Apply in a well-ventilated area. Wear gloves. Preparation: -Surfaces must be close fitting with no gaps, clean, dry and free of oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application: In a clockwise direction, screw the cap and nozzle assembly down all the way to the tube shoulder, puncturing the tube. Remove the cap counterclockwise from the nozzle. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 60 seconds until bond sets. Do not reposition parts. Clean tip with a tissue and replace the cap. Clean-up: After cleaning, wet any tissue used for wiping off the glue with water and dispose of. When cleaning up larger quantities of uncured adhesive, apply water and allow to cure and then scrape up. Note this may result in damage to the surfaces. Cured adhesive may be cut away with caution using a sharp blade, removed with acetone or with boiling water. Note: Acetone is highly flammable and may not be suitable for use on all materials, test surface first. Follow manufacturer’s instructions.
$9.27
Specially formulated to allow more time to align surfaces before setting with less risk of finger bonding and low odour. Non-drip gel formula. Recommended on: Leather, Rubber, Wood, Metal, Porcelain, Paper, Plastic. Properties: No immediate finger sticking. More time to align and reposition* Non-drip formula ideal for vertical application Odourless & non-irritating to skin Water resistant Withstands heavy loads Dries transparent Easy to open, self-piercing and anti-clog cap Choice of applicators: convenient tube or easy grip control with longer nozzle Suitable for use on most surfaces** Solvent free * Loctite Power Easy offers an initial curing time of at least double the standard Loctite Super Glue. **Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$15.50
Specially formulated to allow more time to align surfaces before setting with less risk of finger bonding and low odour. Non-drip gel formula. Recommended on: Leather, Rubber, Wood, Metal, Porcelain, Paper, Plastic. Properties: No immediate finger sticking. More time to align and reposition* Non-drip formula ideal for vertical application Odourless & non-irritating to skin Water resistant Withstands heavy loads Dries transparent Easy to open, self-piercing and anti-clog cap Choice of applicators: convenient tube or easy grip control with a longer nozzle Suitable for use on most surfaces** Solvent-free * Loctite Power Easy offers an initial curing time of at least double the standard Loctite Super Glue. **Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$14.00
Loctite's versatile and reliable Super Glue Liquid is fast and strong and has a range of applicators that will get the job done quickly in every situation. It dries transparent to form a long-lasting invisible bond in seconds. Now with a NEW formula, resisting to all conditions: *Water and dishwashing *Shock *Temperatures from -50°C up to 120°C Recommended on: China, Porcelain, Metal, Rubber, Leather, Wood, Plastic (except PE/PP), Paper. Properties: Multi-use liquid superglue, ideal on non-porous surfaces Water and dishwasher resistant Shock resistant Temperature resistant (from -50°C up to 120°C) Bonds in seconds Withstands heavy loads Dries transparent Easy to open, self-piercing and anti-clog cap Choice of applicators - anti-spill / easy grip / long nozzle / brush-on Suitable for use on most surfaces* Solvent-free *Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$16.00
Clear, 1-part, thixotropic, room temperature-cure, acetoxy silicone vulcanizing compound paste sealant with an acetic acid odor. LOCTITE® SI 595 is a clear, 1-part, thixotropic, room temperature vulcanizing, acetoxy silicone vulcanizing compound paste sealant with an acetic acid odor. It is designed as an excellent adhesive sealant for mechanical assemblies. Typical applications include electrical insulation, protection of leads from mechanical shock, trim bonding, and sealing of ductwork, vents, flues, doors, and windows. Certified to ANSI/NSF Standard 51 for use with plastic materials and components used in food equipment not exceeding +204°C. Formulated to withstand extreme temperature cycling, UV light and ozone Designed for superior bonding and sealing properties to most surfaces (not recommended for concrete) Cures on exposure to moisture in the air to form a tough, flexible, silicone rubber seal Classified by Underwriters Laboratories Inc.® E257711 - Plastics & Components Non-slumping Superior adhesion and flexibility Seals out moisture and contaminants Fills large cracks and seams Non-flammable Non-toxic Resists aging, weathering and thermal cycling without hardening, shrinking or cracking Technical Information Chemical Basis / Base Acetoxy Silicone Colour Black, Clear, White Cure Through Volume 6 mm Fixture Time 30 min. Fixture Time Temperature 30 °C Gap Fill 6 mm Key Characteristics Thixotropic Physical Form Paste Skin Formation Time 120 min. Substrates Ceramic, Composite, Glass, Metal: Aluminum, Metal: Steel, Plastic
$9.82
Adhesive permanently remounts mirrors to windshields LOCTITE® Rearview Mirror Adhesive is approved and used by GM, Ford and Daimler-Chrysler. Permanently remounts mirrors to windshields. Achieves handling strength in seconds; mirror-mounting strength in 15 minutes. Mounting rearview mirrors to windshields.
$25.00
Loctite Go2 Gel contains a revolutionary FLEXTEC® formulation that bonds multi-materials when projects or repairs require higher viscosity, tremendous bond strength, and resistance to extreme conditions. It is a versatile, gap-filling adhesive that bonds, seals and repairs almost all materials. It is ideal for bonds subject to harsh or extreme conditions or for situations where constant flexing is a problem. It can be used indoors and outdoors, has excellent adhesion and high initial grab that cures quickly. Loctite Go2 Gel dries clear and creates a flexible and durable bond which is dishwasher safe and has excellent resistance to vibration, impact, moisture, UV and extreme temperatures, offering long reliability anywhere it is used. Recommended For NOTE: 1See limitations below in the 'not recommended for' section. Compatible with many porous and non-porous materials such as metals1 (aluminum, stainless steel, steel, copper, brass, bronze, zinc, etc.), glass, concrete, ceramic, tiles, natural stones, wood, cork, paper, cardboard, textiles, leather, varnished surfaces1, chipboard, MDF, fiberglass reinforced polyester, rigid PVC, polycarbonate, sanded ABS, and polystyrene foam/Styrofoam™. DIY repairs and modelling work in and around the house. Not Recommended For Before application, carry out tests to ensure the compatibility with non-ferrous metals such as aluminium, copper, bronze and brass as well as with different coatings such as paints, varnishes and powder coatings. Variations in the composition may affect adhesion. Aquariums or potable water systems Archival applications Applications requiring service temperatures below -58°F (-50°C) and above 248°F (120°C) Polyethylene (PE), polypropylene (PP) and polytetrafluoroethylene (PTFE) plastics, metal-to-metal (one surface should be porous) or rubber Applications requiring solvent resistance Applications with prolonged water immersion Safety Precautions Well-ventilated area, gloves. Preparation Use between 41°F (5°C) and 104°F (40°C). Protect work area. Surfaces must be clean and free of grease, dust and other contaminants. For improved adhesion, abrade very smooth surfaces (such as metal) prior to cleaning. Remove cap. Application Apply a thin layer of adhesive to one surface. Immediately position and press parts firmly together within 5 minutes. For difficult bonds, clamp parts or use tape to hold pieces together. Do not move or use parts for at least 2 hours. Full bond strength is achieved in 24 hours. Cure times will increase with lower temperatures and humidity and if bonding two non-porous surfaces. For Gap-Filling: Apply in a thick layer to fill gaps up to 5mm max. Fix or clamp the items together for 1-3 hours and do not touch or move them. In 24 hours, 70% of full adhesion and bond strength is achieved. Cure time is 24 hours for every 2mm of adhesive. To Get High Initial Grip: Apply on both surfaces in thin and even layers. Leave for 3-5 minutes. Use as a contact cement. After, GO2 gel has become tacky, bring the items together immediately and press firmly. Fixation is not necessary in many cases. Note that final strengths decrease when used as a contact glue. Two Non-Porous Surfaces: Bonding two non-porous surfaces can result in a slower cure time and is generally not recommended. If bonding two non-porous surfaces, surfaces can be wetted using a damp cloth, taking care to avoid wetness, pooling water or drop formation, to optimize cure time. Cleanup Clean tools and adhesive residue immediately with mineral spirits. Cured adhesive may be carefully cut away using a sharp-edged tool.
$11.70
Loctite Pre Mixed Epoxy 60 seconds is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 60 seconds and reaches handling strength in 5 to 10 minutes. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. octite Pre Mixed Epoxy 60 seconds does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on Great for crafting projects Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fiberglass, concrete and stone Can be combined with fiberglass cloth for a durable patch Properties High impact resistance: won’t crack when drilled Can be tinted to match surrounding materials Water resistant and can be used outdoors Does not shrink Convenient instant mix syringe Consistently dispenses equal, uniformly mixed amounts of each component Sets in 40 to 60 seconds Quick completion of project HOW TO USE: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from center of plunger. Turn nozzle end up and pull plunger back slightly allowing air bubbles to rise to top. Snap off and discard end of syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$7.91
Part N° 546018 (MA3) LOCTITE AUTOMOTIVE REARVIEW MIRROR ADHESIVE • Special Loctite bonding system for attaching metal rear-view mirror buttons to windscreens. Ideal for larger mounting brackets • Absorbs difference in thermal expansion - also recommended for metal locks and hinges on side windows and glass to metal applications on furniture. Contents: 1 piece of nylon mesh 40mm x 40mm - Diagram 1 Part B. 1 tube of Loctite adhesive - Diagram 1 Part A. Contents are sufficient for one rear-view mirror application. Note: the adhesive must be used with the special nylon mesh Directions for use: - Where convenient, remove the metal bracket from the mirror bracket. Do not damage the metal bracket Place the car in shade for at least one hour before commencing the repair. The ideal temperature for this 2 repair is between 15°C and 25°C Diagram 3: Mark an outline of the bracket on the outside of the windscreen with a marking pen Ensure the position of the bracket will result in the mirror hanging in the correct way. - Remove all old adhesive from the bracket with fine sandpaper, and from the screen with a sharp blade or razor blade. Wipe clean the inside of the screen with an ammonia-based detergent or LOCTITE SF 3 7850 Orange hand cleaner, then wipe again with a clean cloth dampened in Methylated Spirit. Allow drying. Cut the nylon mesh to the exact shape of the metal bracket that will fit onto the windscreen. Hands must be clean and oil-free while doing this. - Cut the tip from the adhesive tube (Dia. 1, Part A), apply the adhesive from the tube and spread over the entire area of the metal bracket - Place the cut to size nylon mesh onto the adhesive on the metal bracket. Important. The adhesive will begin curing within 30 seconds of contact with the nylon mesh. Diagram 7: Note Ensure the bracket is in the correct position (top and bottom front and back) With the nylon mesh and adhesive assembled, press the bracket and mesh against the inside of the windscreen aligned with the marked location and hold firm for a minimum of 30 seconds Wipe off any excess adhesive, Allow adhesive to cure for at least 15 minutes before mounting the mirror to the bracket. Warning: Adhesive may attack some painted surfaces.
$19.95
When you have a minute - tackle even big repairs with the new Loctite 60 seconds All-Purpose Glue. It is fast, strong and repositionable. Perfect results in only 60 seconds. Recommended on: Leather, Rubber, Wood, Metal, Porcelain, Paper, Plastic*. Properties: -Fast: it bonds materials within ca. 60 seconds -Extra strong: it builds up a strength of 100+ kg/cm² within a short time -Repositionable: it gives time to reposition the parts that you want to glue -Ideal for all home repairs, even mid-size and large surfaces -Non-drip gel formula, suitable for vertical applications -It dries transparent -Suitable for use on most surfaces* -Solvent-free -Perfectly bonds non-porous to non-porous materials *Except polyethylene (PE), polypropylene (PP), PTFE, glass, Styropor® and synthetic fibres Step by Step: 1.Ensure surfaces to be bonded are clean, completely dry and close-fitting. 2.Twist the cap/nozzle clockwise onto the tube and remove the cap. 3.Carefully apply the glue on one surface. Press the surfaces together, reposition it as you wish, then press with strong and even pressure for few seconds and leave it undisturbed for 60 seconds. 4.Clean the nozzle, replace the cap and store upright in a cool dry place.
$20.45
LOCTITE 454 is a general-purpose, non-drip gel, instant adhesive that is ideal for vertical surfaces and overhead applications. LOCTITE® 454 is an instant adhesive designed for the assembly of difficult-to-bond materials that require uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. The gel consistency enables overhead and vertical applications. LOCTITE 454 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repair jobs. Universal instant adhesive gel Will not drip or run Non-wicking, especially suited to porous materials Perfect for all quick repairs Ideal for overhead application and vertical faces Bonds similar or dissimilar substrate combinations of wood, metals, ceramics, most plastics Technical Information Colour Clear: Ultra Clear Fixture Time 5 - 10 sec. Full Cure Temperature 77 °F Gap Fill 0.15 mm Key Characteristics General Purpose Physical Form Gel Shear Strength Unit, Grit Blasted Steel psi Shear Strength, Grit Blasted Steel 3200 Specific Gravity 1.05 g/l Specific Gravity Temperature 25 °C Temperature -65 - 250 °F
$7.50
LOCTITE 454 is a general-purpose, non-drip gel, instant adhesive that is ideal for vertical surfaces and overhead applications. LOCTITE® 454 is an instant adhesive designed for the assembly of difficult-to-bond materials that require uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. The gel consistency enables overhead and vertical applications. LOCTITE 454 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repair jobs. Universal instant adhesive gel Will not drip or run Non-wicking, especially suited to porous materials Perfect for all quick repairs Ideal for overhead application and vertical faces Bonds similar or dissimilar substrate combinations of wood, metals, ceramics, most plastics Technical Information Colour Clear: Ultra Clear Fixture Time 5 - 10 sec. Full Cure Temperature 77 °F Gap Fill 0.15 mm Key Characteristics General Purpose Physical Form Gel Shear Strength Unit, Grit Blasted Steel psi Shear Strength, Grit Blasted Steel 3200 Specific Gravity 1.05 g/l Specific Gravity Temperature 25 °C Temperature -65 - 250 °F
$24.59
LOCTITE 406 is a low viscosity, fast curing instant adhesive that is ideal for bonding plastics and elastomeric materials where very fast fixturing is required. LOCTITE® 406 is an instant adhesive designed especially for the fast bonding of plastics and rubbers. This product offers exceptionally low viscosity. When combined with LOCTITE primers for cyanoacrylates, it can also be used on difficult-to-bond plastics. Rapid bonding of plastic & rubber, including EPDM LOCTITE 770 or LOCTITE 7239 primer improves adhesion of difficult-to-bond substrates Technology Cyanoacrylate Chemical Type Ethyl cyanoacrylate Appearance (uncured) Transparent, colorless to straw colored liquid LMS Components One part - requires no mixing Viscosity Low Cure Humidity Application Bonding Key Substrates Plastics and Rubbers TYPICAL CURING PERFORMANCE Under normal conditions, atmospheric moisture initiates the curing process. Although full functional strength is developed in a relatively short time, curing continues for at least 24 hours before full chemical/solvent resistance is developed. Technical Information Colour Clear: Ultra Clear Fixture Time 2.0 - 10.0 sec. Gap Fill 0.05 mm Key Characteristics Viscosity: Low Viscosity Substrates Plastic, Rubber
$18.32
LOCTITE 401 is a general purpose, fast curing, instant adhesive that is ideal for use on porous substrates. LOCTITE® 401 is a fast curing instant adhesive designed for the assembly of difficult-to-bond materials requiring uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. LOCTITE 401 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repairs and all types of small emergency repairs. Universal instant adhesive Very high strength on close-fitting parts Perfect for all quick repairs and all types of small emergency repairs. Bonds a wide range of similar or dissimilar substrates (metals, rubber, wood, cardboard, ceramics as well as most plastics) Technical Information Colour Clear: Ultra Clear Fixture Time 3 - 10 sec. Full Cure Temperature 77 °F Gap Fill 0.15 mm Key Characteristics General Purpose, Viscosity: Low Viscosity Shear Strength Unit, Grit Blasted Steel psi Shear Strength, Grit Blasted Steel 3200 Specific Gravity 1.05 g/l Specific Gravity Temperature 25 °C Temperature -65 - 250 °F Viscosity 110 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$5.87
LOCTITE 401 is a general purpose, fast curing, instant adhesive that is ideal for use on porous substrates. LOCTITE® 401 is a fast curing instant adhesive designed for the assembly of difficult-to-bond materials requiring uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. LOCTITE 401 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repairs and all types of small emergency repairs. Universal instant adhesive Very high strength on close-fitting parts Perfect for all quick repairs and all types of small emergency repairs. Bonds a wide range of similar or dissimilar substrates (metals, rubber, wood, cardboard, ceramics as well as most plastics) Technical Information Colour Clear: Ultra Clear Fixture Time 3 - 10 sec. Full Cure Temperature 77 °F Gap Fill 0.15 mm Key Characteristics General Purpose, Viscosity: Low Viscosity Shear Strength Unit, Grit Blasted Steel psi Shear Strength, Grit Blasted Steel 3200 Specific Gravity 1.05 g/l Specific Gravity Temperature 25 °C Temperature -65 - 250 °F Viscosity 110 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$18.32
Bonds metals, ceramics, concrete, fibreglass, marble and wood. Syringe dispenser accurately measures equal amounts of resin and hardener to prevent wastage. Fast curing, cure commences in five minutes and reaches full cure in one hour. When cured, the bond is transparent and virtually colourless. Loctite 5 Minute Epoxy Adhesive's premium formulation is solvent-free and 100% solids providing a non-shrink, environmentally friendly bond. High viscosity provides a good gap-filling ability. DIRECTIONS FOR USE: 1. Surfaces must be clean and dry. If possible, roughen surface with sandpaper to improve keying and bonding. 2. Cut tips of twin nozzle with a sharp knife and remove nozzle cap from syringe plunger. 3. Push the twin plunger to squeeze out equal amounts of resin and hardener in the amounts required. 4. Mix the resin and hardener for one or two minutes until the colour is completely uniform. 5. Apply immediately to both surfaces and press together. Pressure clamping is not necessary, but allow the adhesive to set for at least 5 minutes before moving. Remove any excess adhesive immediately. 6. Important. After dispensing product be certain to insert plug supplied in the nozzle of the syringe to prevent waste. Preferably store in an upright position as packaged. Structural Bonding - Fast Cure. Sets in 5 minutes. Sets in 5 minutes. Good chemical resistance. Fixture time: 4-6 min Temperature Resistance: Up to 180°F (82°C)
$15.11
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
$13.11
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
$40.93
PlasticWeld is a specially formulated two-part adhesive and epoxy filler system that provides for strong, lasting repairs. PlasticWeld will bond a variety of surfaces, such as metal, composites, fiberglass and others. PlasticWeld sets in 5 minutes at room temperature and is fully cured in 1 hour. Using a 1:1 mixing ratio, PlasticWeld combines to a tensile strength of 3200 PSI and cures to an off-white color. GREAT FOR Most Hard Plastics ABS Fibreglass PVC Glass Vinyl STRENGTH 3200 PSI SET TIME 5 Minutes CURE TIME 1 Hour CURE COLOR Off White USE ON Automotive Ceramic Epoxy & Adhesives Fibreglass Plastic/Composite/PVC And More
$14.95
Gorilla® Super Glue Precise Gel is an easy-to-use, thicker formula* combined with a precision tip and large tube, so it’s easy to apply with control and precision. Great for multiple surfaces and vertical applications. Directions 1. Protect work area from spills. 2. Clean and dry surfaces to be bonded. 3. To puncture, place cap and nozzle on the tube and tighten down. 4. Apply a small amount of Gorilla® Super Glue Precise Gel to one surface. Only one drop per sq. inch recommended. Set time can vary based on the amount of glue and type of surface glued. Excess glue can cause delayed or failed bond. 5. Press the two surfaces together for about 10-45 seconds. Wait 24 hours for full cure. 6. After using, clean nozzle with a dry cloth and replace the outer cap. Store in a cool, dry place.
$14.76
Glues Australia presents the Gorilla Super Glue Micro Precise Gel, an innovative adhesive solution tailored for a broad spectrum of applications. This product stands out as a versatile and powerful tool for creating enduring bonds in seconds. Product Features: Fast-Acting, Strong Formula: This glue sets in 10-45 seconds, providing a robust and lasting bond quickly. Controlled, No-Run Gel Formula: Its gel consistency ensures precise application, perfect for vertical surfaces and detailed projects. Versatile Bonding: Suitable for a variety of materials including plastic*, wood, metal, ceramic, rubber, and more. Directions for Use: Surfaces should be dry, clean, and free of dust. To open, turn the cap clockwise to puncture the seal. Open the nozzle by turning the green cap counter-clockwise. Dispense by squeezing, applying a small amount to one surface. Press surfaces together for 10-45 seconds. After use, clean the nozzle and store in a cool, dry place. Technical Specifications: Application Temperature: Room temperature Service Temperature Range: -65° to 220° F Cured Color: Clear Sandable: Yes Storage Tips: Store in a cool, dry location away from children and animals. Frequently Asked Questions: How does it differ from other Gorilla Glue products? It's a cyanoacrylate adhesive that bonds quickly without moisture or clamp time, unlike polyurethane-based Gorilla Glue. What is Impact Tough™? A formula designed to withstand bumps and drops, ensuring a strong and resilient bond. Can it bond all plastics? It is effective on most plastics, but certain types like polyethylene may need special preparation. How to remove from skin? For spills, immediately wash with soapy water. For cured glue, soak in warm soapy water, then gently wiggle the area. Is it food safe? It is not intended for any application involving food contact. Safety Information: For bonded skin or medical emergencies, contact Australian Poisons Information. The Gorilla Super Glue Micro Precise Gel is an essential addition to any toolkit. Its combination of strength, versatility, and ease of use makes it an ideal choice for various household and professional tasks. Available now at Glues Australia, it's the perfect solution for your adhesive needs."
$17.00
Gorilla Super Glue Brush & Nozzle offers 2 easy ways to dispense for control and accuracy. Brush & Nozzle features a precision tip nozzle and fine bristle brush that allow the user to control their super glue application, making it perfect for any project. Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–45 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear, unlike any other super glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. Super glue, also referred to as cyanoacrylate glue, or CA glue works on a variety of materials, including plastic, metal, fabric, stone, ceramic, paper, rubber and more. It’s Gorilla tough, every time. Product Features -Two ways to dispense for greater control and versatility! -Fine bristle brush for controlled coverage with less mess -Precision tip nozzle for quick, easy dispensing -Impact Tough: Unique rubber particles increase impact resistance and strength -Fast-setting: Dries in 10-45 seconds, no clamping required. Directions -Protect Work Area From Spills -Clean and Dry Surfaces to Be Bonded -Apply Gorilla Super Glue -Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch. -To use the nozzle, unscrew the upper cap and remove. To use the brush, unscrew the full cap and wipe the brush on the inner rim of the bottle to remove excess glue. Secure Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
$15.00
Its high strength and quick set time make Gorilla Super Glue the go-to for a variety of household projects. Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–30 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear unlike any other instant glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. Clamp Time: 10-30 Seconds // Open Time: Not Repositionable Dry Time: Light Handling after 1-5 Minutes // Dry Color: Translucent Full Cure: 24 Hours DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Apply Gorilla Super Glue Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch. Secure Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
$14.99
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. PRODUCT FEATURES CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More APPLICATION TEMPERATURE – 0°C to 37.8° C, best at room temperature SERVICE TEMPERATURE – -28.9° to 82.2° C OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – Minimal What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight fitting joints. It’s perfect for a fix you need done fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also minimally gap filling, which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant, and can withstand intermittent exposures, however is not meant for a constant soak. Original Gorilla Glue is 100% waterproof and can withstand soaking and longer term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$14.92
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. Features: CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More Directions All surfaces must be clean and tight fitting. Clear Gorilla Glue will stain clothes. 1. Damp It For non-porous surfaces only (i.e. metal, glass, plastics), lightly dampen one surface with water. Do not add water to the bottle. 2. Glue It Apply Clear Gorilla Glue to surfaces. Best at room temperature. 3. Clamp-It Clamp objects together for 2 hours. Full cure in 24 hrs. You can use heavy objects to achieve clamping pressure. *Not recommended for use on polyethylene or polypropylene plastics. Storage Tips After each use, wipe nozzle clean with a dry cloth and tightly replace lid. Store in a cool, dry place with exposure to light. Lack of light and heat can cause the product to yellow. Cured glue can be removed from work surface with chisel, scraper or sandpaper. Store away from children and animals. Specs: APPLICATION TEMPERATURE – 32° to 100° F, best at room temperature SERVICE TEMPERATURE – -20° to 180° F OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – No FAQS What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight-fitting joints. It’s perfect for a fix you need doing fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also gap filling which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant and can withstand intermittent exposures, however, is not meant for a constant soak. Original or White Gorilla Glue is 100% waterproof and can withstand soaking and longer-term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$12.90
APPLICATION 1. Pierce seal at end of tube by turning nozzle and cap clockwise. 2. Ensure the working surface is clean, dry, free of dust or any grease. 3. Apply adhesive sparingly to one surface only. 4. Place surfaces together and press firmly for 10 - 60 seconds. Adequate for practical purposes after 30 minutes STORAGE: 5. After use. clean nozzle immediately with a cloth, replace cap and store upright between 5- 25°C. Avoid strong light and heat sources LIMITATION: Not recommended for polyethylene, polyester plastic & glass. Not suitable for use on items which contain hot liquids eg. Cups, mugs. May cause leather to discolour or harden. Test on a hidden area before use if in doubt. For interior use only.
$4.50
Glue Dots® Repositionable Double-Sided Sheets can be custom cut to any size or shape to provide adhesive coverage for projects both big and small. Ideal for hanging lightweight items, securing rugs to hardwood and tile floors, and can be easily removed. Not recommended for heavy or bulky materials that require a permanent bond. Glue Strength - Temporary Features/Benefits: Resealable Bag | Easy to Store Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$8.73
Repositionable Dots™ Dot N Go® dispenser fits in the palm of your hand and can be used as a 'second set of hands' to hold small, lightweight items in place temporarily. It's perfect for quick fixes and repairs around the home. Not recommended for heavy or bulky materials that require a permanent bond. Glue Strength - Temporary Features/Benefits: Hand-held Dispenser | Easy to Use Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$9.70
Advanced Strength Dots™ Dot N Go® fits in the palm of your hand and is perfect for quick fixes and repairs. With a small footprint, the Advanced Strength Dot N Go stores easily in a toolbox or drawer for easy access. Ideal for tough jobs and DIY projects that require exceptional holding power. Not recommended for temporary applications or delicate items. Glue Strength - Super-Strength (Holds up to 8 lbs.) Features/Benefits: Hand-held Dispenser | Easy to Use Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free Adhesive Size: 3/8 in. diameter Adhesive Color: Amber Quantity: 125 Adhesives
$8.95
Glue Dots® Advanced Strength Double-Sided Sheets can be custom cut to any size or shape to provide adhesive coverage for projects both big and small. Ideal for tough jobs and DIY projects that require exceptional holding power. Not recommended for temporary applications or delicate items. Glue Strength - Super-Strength (Holds up to 8 lbs.) Features/Benefits: Resealable Bag | Easy to Store Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$7.98
Craft Glue Dots® are versatile, permanent adhesives ideal for heavier materials like wood or metal, large embellishments or thick cardstock. Glue Strength - Super-Strength Features/Benefits: Hand-held Dispenser | Easy to Use Acid Free| Photo Safe Non Toxic | Kid Friendly Specifications Adhesive Size: 3/8 in. diameter Adhesive Color: Clear Quantity: 200 Adhesives
$12.74
Elmer’s School Glue is a washable, no-run glue that is easy to use and stays where you put it. - It is safe, non-toxic and washable, so accidental messes mean easy clean-up! - Perfect for making slime - Colour: White How can I un-clog my glue cap and what’s the proper way to clean it? The glue caps can actually be taken apart to help remove any blockage. Simply open the cap as far as it will go and then pull the orange part straight up and it should "pop" off. This should allow you to easily access any blockage. The blockage can be cleared with something like a toothpick or paper clip. You can also soak these separated parts in room temperature water which should help to more easily free up any blockage. Once clear, the orange part can simply be pressed/snapped back into position. Watch the how-to un-clog a glue cap video for visual instructions. Is glue made from horses or other animals? No, Elmer's does not make glue from horses or use animals or animal parts. Elmer's products are made from synthetic materials and are not derived from processing horses, cows or any other animals. Why doesn't glue stick to inside of the bottle? As long as the glue remains inside the bottle away from air it will remain fluid. Glue hardens when there is a loss of water from the formula. Exposure to the atmosphere will cause the water to evaporate and make the glue harden. That's why it is important to keep the cap on the glue bottle closed to prevent hardening or drying out. I have a milk allergy. Are your products safe for me to use? Elmer's products are derived from synthetic materials, not any type of animal or milk protein. Of course, if you experience any kind of allergic reaction, be sure to check with your doctor regardless of the type of product you are using. How long can I keep glue? If stored properly and capped tightly, Elmer's school glues and wood glues have an average shelf life of 2 years. Krazy Glue, also known as a cyanoacrylate, has a shelf life of approximately 12 - 18 months. Is Elmer's glue gluten free? All of Elmer's products are gluten free except for the Elmer's Finger Paints. The finger paints contain wheat and oat products. Is Elmer's glue acid free? No. Most of Elmer's glues that are acid-free are labelled as such. Some of Elmer's most popular acid-free products include all of Elmer's glue stick, rubber cement and spray adhesive products.
$24.20
Elmer’s School Glue is a washable, no-run glue that is easy to use and stays where you put it. - It is safe, non-toxic and washable, so accidental messes mean easy clean-up! - Perfect for making slime - Colour: White - Pack size: 225ml How can I un-clog my glue cap and what’s the proper way to clean it? The glue caps can actually be taken apart to help remove any blockage. Simply open the cap as far as it will go and then pull the orange part straight up and it should "pop" off. This should allow you to easily access any blockage. The blockage can be cleared with something like a toothpick or paper clip. You can also soak these separated parts in room temperature water which should help to more easily free up any blockage. Once clear, the orange part can simply be pressed/snapped back into position. Watch the how-to un-clog a glue cap video for visual instructions. Is glue made from horses or other animals? No, Elmer's does not make glue from horses or use animals or animal parts. Elmer's products are made from synthetic materials and are not derived from processing horses, cows or any other animals. Why doesn't glue stick to inside of the bottle? As long as the glue remains inside the bottle away from air it will remain fluid. Glue hardens when there is a loss of water from the formula. Exposure to the atmosphere will cause the water to evaporate and make the glue harden. That's why it is important to keep the cap on the glue bottle closed to prevent hardening or drying out. I have a milk allergy. Are your products safe for me to use? Elmer's products are derived from synthetic materials, not any type of animal or milk protein. Of course, if you experience any kind of allergic reaction, be sure to check with your doctor regardless of the type of product you are using. How long can I keep glue? If stored properly and capped tightly, Elmer's school glues and wood glues have an average shelf life of 2 years. Krazy Glue, also known as a cyanoacrylate, has a shelf life of approximately 12 - 18 months. Is Elmer's glue gluten free? All of Elmer's products are gluten free except for the Elmer's Finger Paints. The finger paints contain wheat and oat products. Is Elmer's glue acid free? No. Most of Elmer's glues that are acid-free are labelled as such. Some of Elmer's most popular acid-free products include all of Elmer's glue stick, rubber cement and spray adhesive products.
$6.50
A water-based protective sealer which penetrates and cures within the pores of the grout. The sealer is fast drying and the bottle contains a brush for easy application. A water-based protective sealer Deep penetrating into the grout Easy to use brush for perfect sealing over grout Fast drying formula Coverage Seals up to 25m2 per 250ml
$20.03
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$8.33
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$8.83
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$7.91
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$6.82
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$9.06
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$8.83
You have seen 240 out of 272 products
Clear-drying adhesives, sealants and fillers for invisible bonds and neat edges on glass, plastics and décor. Ideal where appearance matters. Use filters to refine by chemistry, set speed and temperature rating. Always check the product page and TDS/SDS for prep and cure.
