For: Plumbing

SikaSeal® Kitchen and Bathroom SikaSeal® Kitchen and Bathroom is a one-component, neutral-curing, low-odour silicone sealant with excellent adhesion and a long shelf life for DIY applications. It cures at room temperature under the action of atmospheric moisture to give a permanently flexible silicone rubber. Uses Glass and enamel Ceramics and tiles Aluminium, steel, zinc, copper Plastic laminates Rubber Stainless steel Concrete and grouts Characteristics / Advantages Excellent adhesion Great weatherability Non-sag Great tooling characteristics Long-term mould resistance Interior and exterior usage Fast curing Colours White Beige Black Charcoal Transparent Alabaster Almond Ivory Off White Stone Pewter Grey Mid Grey Stone Brown Packaging 300ml cartridges, 12 cartridges per box Shelf Life 12 months from the date of production if stored in undamaged and unopened original sealed containers, in dry conditions, and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base: Neutral curing Density: 0.98 g/cm³ @ 23ºC Skin/Forming Time: 10-15 minutes @ 23ºC/50% r.h. Curing Rate: 72 hours @ 23ºC/50% r.h. Consistency: Non-sag Mechanical/Physical Properties Tensile Strength: 0.4 N/mm² @ 23ºC/50% r.h. Shore A Hardness: 20 SHA E-Modulus: 0.30 N/mm² at 10% elongation @ 23ºC/50% r.h. Ultimate Elongation: 300% Anti-mildew Property: 0 level

Read more less

The Premium Wet Area Sealant Wet areas Baths, showers, toilets Easy to use Contains strong fungicides to fight mould Maxisil A Ceramic Silicone is an acetic cure silicone recommended for all ceramic tile areas, especially for expansion joints in bathrooms, kitchens, and flooring sectors. Built-in fungicides for mould resistance For both exterior and interior use Excellent weatherability, resistant to ageing and UV radiation Resistant to chemicals and temperature Primerless adhesion to clean, dry surfaces such as ceramics, glass, acrylics, aluminium, and painted wood Very good tooling and smoothing properties Time-saving with an easy cleanup system Please note that colour samples are not true to the actual colour. This is a guide only. Characteristics 1-component acetate-curing silicone sealant Excellent weathering, ageing, and UV resistance Enables a great finish, will not string during application Good tooling and smoothing properties Contains fungicides Medium skin formation time for easy handling Very good adhesion on ceramic substrates Primerless adhesion to many substrates Stress expansion modulus at 100% (DIN 53 504, S3A): 0.3 N/mm² Meets DIN 18545, part 2D (German industrial standard) Available in a variety of colours (custom colours available upon request) Fields of Application Sealing connection joints between ceramic tiles, showers, baths, and flooring sections Expansion/movement joints in bathrooms and wet areas Connection joints on door and window frames Sealing double-glazing joints Glass block glazing Sealing general building substrates Suitable for interior and exterior use Important Information Before application, ensure materials in the contact area are compatible with the sealant and with each other to prevent damage or discoloration. If in doubt, consult the manufacturers of surrounding substrates. While curing, small amounts of acetic acid are released — ensure good ventilation After curing, the product is odourless and harmless Thicker silicone layers require longer vulcanisation time Not for full-surface bonding unless construction prerequisites are met For layers over 15mm, contact our technical department Avoid contact with bitumen-containing materials or those releasing solvents (e.g. butyl, EPDM, neoprene, bituminous paints) When replacing mould-contaminated joints, remove all old sealant and treat areas with Maxisil Anti-Mildew Spray Technical Properties Skin-forming time (23°C / 50% RAH) ~ 15 min Curing in 24h (23°C / 50% RAH) ~ 2–3 mm Processing temperature +5°C to +35°C Viscosity (23°C) Pasty, stable Density (23°C, ISO 1183-1) ~ 1.0 g/cm³ Shore A hardness (ISO 868) ~ 20 Permissible movement capability —

Read more less

T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C.​, its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other. Features Waterproof backing enhanced with R-Flex Technology™ for greater durability Can be used underwater UV resistant All-weather: withstands temperatures from -56C to 93C. WATERPROOF ADHESION Extra thick butyl-based adhesive means durable repairs, even under water. T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other. FEATURES: Waterproof backing enhanced with R-Flex Technology™ for greater durability Can be used underwater UV resistant All-weather: withstands temperatures from -56C to 93C. WATERPROOF ADHESION Extra thick butyl-based adhesive means durable repairs, even under water. R-FLEX TECHNOLOGY Durable, flexible and UV resistant backing for long lasting repairs. ALL WEATHER Waterproof and built to withstand extreme temperatures from -56C to 93C. Durable, flexible and UV resistant backing for long lasting repairs. ALL WEATHER Waterproof and built to withstand extreme temperatures from -56C to 93C.

Read more less

T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C.​, its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other. Features Waterproof backing enhanced with R-Flex Technology™ for greater durability Can be used underwater UV resistant All-weather: withstands temperatures from -56C to 93C. WATERPROOF ADHESION Extra thick butyl-based adhesive means durable repairs, even under water. T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other. FEATURES: Waterproof backing enhanced with R-Flex Technology™ for greater durability Can be used underwater UV resistant All-weather: withstands temperatures from -56C to 93C. WATERPROOF ADHESION Extra thick butyl-based adhesive means durable repairs, even under water. R-FLEX TECHNOLOGY Durable, flexible and UV resistant backing for long lasting repairs. ALL WEATHER Waterproof and built to withstand extreme temperatures from -56C to 93C. Durable, flexible and UV resistant backing for long lasting repairs. ALL WEATHER Waterproof and built to withstand extreme temperatures from -56C to 93C.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.

Read more less

Showerbond is a solvent based, fast grab, gun grade adhesive. It has been specifically formulated for bonding plastic shower linings to gypsum plasterboard or fibre cement wall linings, as well as timber. Use Showerbond is used for bonding plastic shower linings to wall linings. Advantages  Fast curing.  Will not damage plastic shower liners.  Panels can be relocated for up to 30 minutes after positioning.  Excellent adhesion to most common building materials.  Easy to apply and clean up.  Recommended for use with Seratone Silverseal, Clearlite Showers, Duracryl® ,and Athena Showers Product Data Form: Smooth paste Colour: Green Storage & Shelf Life: Twelve (12) months when stored in original unopened containers in a cool, dry place away from naked flames. Packaging: Showerbond is supplied in 300 ml cartridges. Technical Data Solids content: 65% approx. by weight Cure type: Solvent release Cure rate: 24 hours @ 20C Application temperature: 5C to 35C Skinning time: 1 minute Relocation time: Up to 30 minutes, depending on temperature and ventilation Flammability: Flammable solvents are released during cure Toxicity: Non toxic when cured Movement accommodation: Slight, will accept normal building movement Coverage: On average, one cartridge of Showerbond will supply 20 metres of 5 mm bead. Application Conditions Surface Preparation Ensure both surfaces to be bonded are clean, dry and grease free. Cut nozzle on cartridge as shown below so that a 5-6 mm bead will be extruded. Application  Apply a 5-6 mm bead in vertical lines at 100 mm centres onto substrate, and apply continuous bead within 15 mm of the perimeter line of the shower lining.  Place shower lining onto wall within 10 minutes and firmly press the entire sheet with your hands so that full contact is made with all beads of adhesive.  Brace the lining as required in the shower manufacturer's installation instructions.  Bracing if required should remain in position for not less than 18 hours. The shower should not be used for at least 24 hours after the wall lining has been installed. Do not apply blobs of adhesive. These will cause unsightly undulations and buckles in the sheet.

Read more less

Selleys Wet Area Matt White: The Lasting Choice for Wet Areas Key Features Matt finish for elegant look 100% silicone sealant 25-year guarantee against cracking or peeling Waterproof seal with superior adhesion Mould-resistant formula Non-corrosive, neutral cure Best For Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures. Suitable Materials Ceramic, Glazed & Porcelain Fixtures Metal, Copper & Brass Fittings Plastic Laminates Rubber Glass Stainless Steel Concrete & Grouts Many Plastics including Polystyrene How to Use Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application. Limitations Not paintable Not suitable for certain materials and uses Handy Tips Mask sides for neater joints. Work in manageable sections for a smoother finish. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping. Additional Info Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.

Read more less

Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.

Read more less

Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.

Read more less

Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.

Read more less

Selleys N Mastic is a non-hardening, waterproof sealing putty designed for a wide range of applications where long-lasting flexibility is crucial. Ideal for sealing joints, gaps around windows, and roofing, it ensures that structures remain protected from water ingress. The unique formula remains pliable, making it perfect for environments where movement and expansion are expected. Whether you're sealing an outdoor roof gutter, securing window frames, or filling gaps in an air conditioning system, Selleys N Mastic provides a professional-grade finish with no cracking or crumbling. The product is also suitable for metal, glass, concrete, and brick, making it a versatile solution for residential, commercial, and industrial projects. N-Mastic is a non-skinning polybutene-based compound. It will remain permanently soft and paste-like. Uses N-Mastic is suitable for sealing concealed lap joints between plastics, metals, timber, glass, masonry, and expanded foam panels. It may be used in the installation of cool rooms, prefabricated construction and gasket sealed windscreens to exclude draughts and water penetration through joints in materials. Technical Features Non-hardening – remains permanently flexible to provide a lasting seal Good adhesion – adheres well to most substrates Moisture resistance – provides an excellent barrier to moisture vapour Microbe resistance – resists microbial attack Low shrinkage – avoids the risk of sealant pulling away from joint surfaces Wide service temperatures – withstands –40oC to +80oC service conditions Application Tips Due to the non-skinning, non-hardening nature of the sealant, N-Mastic should not be used in exposed joints where dirt pick-up or hand contact can be a problem. As N-Mastic is not elastomeric, it should not be used in areas subject to considerable dynamic stress. Although N-Mastic is resistant to static pressures, a curing sealant is recommended where this is a critical factor. N-Mastic is not recommended for sealing lap joints in mobile homes, truck bodies, etc., as significant vibration and flexing occur during travel. Technical Details and Performance Indicative information only, not to be used for setting specifications. Colour Off White Specific Gravity 1.4g/mL Consistency Non-sag Slump (MIL-S-8802, @ 32oC ) 2.5mm maximum Viscosity (Brookfield HAF 7/2 @ 25oC ) 10,000 – 14,000 Poise Flash Point 85oC Storage Life (25oC ) Indefinite Packaging Plastic cartridge (410g) Performance Properties Shrinkage (% maximum) 5 Service Temperature –40oC to +80oC Life Expectancy Up to 20 years Clean Up Sealant may be removed with a cloth dampened with kerosene or mineral spirits

Read more less

A versatile hand kneadable, fast setting, non-rusting co-extruded epoxy repair system that can be used for repairing ferrous and aluminium metal items. It comes in a handy roll form, with the black hardener encapsulated in the grey resin part. The product hardens in 5-10 minutes, after mixing, to a black metal-like material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under water (but dry surfaces for application are best and recommended). Rapid Set (less than 10 minutes). Can be used for fuel resistant repairs. Appearance Dries Dark Grey/Charcoal Where can this product be used? Rebuilding engine parts and rusted metal etc Repairing a hole in a fuel tank Repair of iron pipes, tools and equipment Repair stripped threads Forming of nuts and bolts in place Attaching fixtures and signs Fixing radiators Repairing holes in cars and boats Patching ducts and tanks Making prototypes Thread locking Repair of down pipes and gutters Anchoring of bolts Repairing your metal outdoor furniture Set time increases at temperatures below 20°C Not recommended for plastic fuel tanks Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Not tested for drinking water contact to AS/NZ 4020:2005 What materials is this product suitable for? Steel Wide range of terrous metal and aluminium items Most plastics (pre-test required) Glass How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning Cut off required amount. Replace disc on remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to uniform colour. If mixing is difficult, warm to room temperature. Apply with pressure to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Steel will harden and begin to form a strong bond. After 60 minutes Knead-It Steel may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour, and feel a mild heat radiating from thre knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Store in a cool place for maximum shelf life Use Knead-It Multi Purpous for applications in contact with drinking water. Use Knead-It Aqua for applications in wet/submerged areas. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Steel. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.

Read more less

A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.

Read more less

A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.

Read more less

A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.

Read more less

Features Resists intense heat Sets hard Water clean up Where can this product be used? Repairing bricks in fireplaces and chimneys Sealing flues in pot-belly stoves Filling cracks in ironworks and bricks  What materials is this product suitable for? Brick Metal Concrete How to Use: Remove all dust, grease and loose debris before applying material. Dampen the cavities on porous surfaces for better adhesion. Apply Fireproof Cement firmly into holes and cracks with a damp knife or spatula. Allow Fireproof Cement to dry a minimum of 48 hours before exposure to heat. If Fireproof Cement is stiff slacken with a little water. Limitations: Fireproof Cement is not an adhesive - it is a filling compound. Not recommended for external use e.g. BBQ's, incinerators etc. Fireproof Cement is not suitable for use in kilns. Fireproof Cement is not recommended for moving joints such as expansion joints as it sets rigidly Hardened material cannot be resoftened with water.

Read more less

Selleys All Clear Crystal: The Ultimate Multipurpose Sealant Key Features Works on wet, oily, and dirty surfaces Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Best For Metal, Timber, Glass, Glazed tiles, Brick, Stone, and many plastics (may damage polystyrene and polycarbonate). Applications Sky lights Window frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' entries Shower screens Sinks and basins Caravans and recreational vehicles How to Use Use only in a well-ventilated area. Ensure surface is clean and dry. Apply with a caulking gun and smooth with a tool dipped in turps. Limitations May damage some plastics Not for permanent water immersion Not suitable for use over silicones or polystyrene foam Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by cutting and scraping. Technology & Cure Time Solvent-based, with a full cure time of 48-72 hours. For both interior and exterior use.

Read more less

Silicone 401 RTV is a one part ready to use, acid cure, room temperature vulcanising (RTV), silicone adhesive sealant. It cures rapidly on exposure to atmospheric moisture to form a versatile, durable, resilient silicone rubber. It is available in clear. Uses Silicone 401 is suitable for form-in-place gaskets and for adhesive, sealing and electrical insulating applications in manufacturing and plant maintenance. Technical Features Wide Temperature Tolerance: Remains permanently flexible under operating temperatures from – 60oC to 205oC, and will tolerate short periods of 260oC Good Chemical Resistance: Good resistance to most organic and inorganic chemicals, solvents and oils Primerless Adhesion: Adheres without primer to many metal, glass, ceramic, rigid plastic, rubber painted and wood substrates Non-toxic: Suitable for incidental food contact in food handling equipment and food contact surfaces Excellent Weatherability: Excellent resistance to ozone, UV light and ageing Good Electrical Insulating Properties: Insulating properties are comparable to other insulating rubbers at room temperature, though performs better than many other rubbers at higher temperatures and water has little effect on these properties Application Tips Not recommended for use with petrol, distillate and some other hydrocarbon solvents. These can cause softening and swelling which is undesirable in some applications. Do not use in totally confined joints where sealant is not exposed to atmospheric moisture Chemical compatibility should be tested for each application under consideration Cannot be over-painted Technical Details and Performance Indicative information only, not to be used for setting specifications. Typical Application Properties Consistency Non – sag, gun grade Tack Free Time (25oC, 50% r.h.): 15 – 20 minutes Skin Forming Time 5 to 10 minutes (depending on weather conditions) Cure Time (3mm Section @ 25oC, 50% R.H.): 24 hours Shrinkage During Curing Approximately 3.5% by volume Specific Gravity 1.04 Storage Life (Below 30oC in original unopened container):12 months Typical Mechanical Performance Properties (3 day cure @ 25oC, 50% R.H.) Tensile Strength (MPa) 1.2 Ultimate Elongation % 400 Hardness (Shore A) 25 Tear Strength (N/mm) 5.0 Joint Movement Capability ± 25% Typical Electrical Properties (at Room Temperature) Dielectric Strength kv/mm 21 Dielectric Constant @50Hz to 5MHz 2.6-2.8 Dissipation Factor Tan @50Hz-5MHz 20×10-4 to 5×10-4 Volume Resistivity (ohm-cm) 1×1013 (wet 60oC) 1×1014 (dry 23oC) Typical Thermal Properties Brittle Point –60oC Maximum Continuous Operating Temperatures 205oC Maximum Intermittent Operating Temperatures 260oC

Read more less

Prep marathon is the ultimate metal big-wig in crevices and corners. A scrub that trims down, it gets into the nooks to clean while also protecting with a silicone shield. It’s tough on calcium, rust and scale deposits which makes it ideal for use on tiles, porcelain sinks bathrooms and showers or baths. Get Prep Marathon today!

Read more less

Marathon Scale and Rust Remover CONCENTRATED 2L Bottle Tough on calcium, rust and scale deposits.  Ideal to use on tiles, porcelain, sinks, showers and baths

Read more less

PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.

Read more less

PC-11® thrives in wet environments. It is resistant to water whether it is fresh or salt. Thick consistency like PC-7® and long open time (30 min). Work horizontal or vertical, indoor or outdoor. Wet, dry or under water. Whether you are working on an area where you just can’t remove water and moisture or you want the white colour for your repair, PC-11® is your choice. Choose PC-11® for ceramic repairs, pools and spas, fibreglass boats, tubs and sinks, stock tanks and thousands of other repairs. It has excellent adhesive properties bonding metals, fibreglass, wood, tile and some plastics such as ABS and rigid PVC. Ample open time allows tooling or positioning in order to tackle larger and challenging jobs. When mixed, the epoxy, part A (white) and the hardener part B (lt. blue) react to form a bond of tremendous strength and flexibility. The PC-11® formulation is slow curing, but slow can be a good thing especially for large tasks. WORKING TIME: 30 MINUTES CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE) PC-11® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Not quite as thick as peanut butter. Here are just a few specific uses (there are hundreds of other uses): Reattach missing swimming pool tiles. Patch a hole in a fibreglass canoe or the fibreglass keel of a fishing boat. Repair cracked or damage swimming pool or hot tub skimmer. Waterproof and Seal cracked fibreglass. Seal screw holes to hatch lids or seating. Attach fish locators to transom. Repair stock tanks. Repair broken refrigerator door shelf fixtures. Repair broken pottery. Repair shower basin or antique bath tub. Seal leaking air conditioner drip pan. Seal underground conduit. How to prepare a surface for bonding with PC-11® Epoxy Paste Remove contaminants such as dust, dirt, oil, barnacles and grime with a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. For a wet or underwater surface; clean contaminants as best as you can. Solvents will not help you in this situation. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-11® Epoxy Paste application Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-11® cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. Can PC-11® be used in Aquariums? There is the potential for PC-11® part A and part B to harm sea life but properly measured and mixed PC-11® has been used safely in fresh and saltwater aquariums. It is important that part A and B are thoroughly and completely mixed. What plastics does PC-11® stick to? PC-11® has good adhesion to Rigid PVC and CPVC, polyester and fiberglass, polyurethane, ABS and Bakelite. What plastics does PC-11® not stick to? PC-11® does not stick to polyethylene, polypropylene, HDPE, polystyrene, nylon, acrylic, Teflon, and polycarbonate. What rubbers does PC-11® stick to? PC-11® sticks to SBR, Buna, and polyurethane rubbers and does not stick to EPDM, vinyl and neoprene rubbers. What temperatures can PC-11® be applied? PC-11® cures very slowly at temperatures below 50°F (10°C). At or below freezing temperatures the PC-11® will stop curing. In hot conditions, above 95°F (35°C), PC-11® will cure rapidly reducing the working or application time. Can gel coat be applied to PC-11®? Gel coat will not cure properly in direct contact with PC-11®. It is important that repairs made with PC-11® be sealed with a suitable primer/sealer before applying a gel coat. Can PC-11® be painted? Yes. It is good practice to apply a premium stain sealing primer to repairs made with PC-11® prior to the finish coat. Will PC-11® yellow in direct sunlight? Yes, PC-11® yellows in direct sunlight. PC-11® resists ultraviolet light but will still gradually change colour. Prime and paint if the colour is important. Can PC-11® be thinned with solvent? PC-11® does not contain solvents. Acetone and denatured alcohol (ethanol) are compatible but will extend the cure time and decrease the hardness. Other solvents such as mineral spirits, paint thinner and turpentine are not compatible. PC-11® is a simple one to one mix, but how accurately does the measurement need to be? The volume of part A to part B should be close to equal. A slight excess of part A is preferable to an excess of part B. Excess of part B will not accelerate the curing and it may make it softer.

Read more less

PC-Plumbing™ Epoxy Putty is for pipes. Use PC-Plumbing™ to stop leaks in less than 60 minutes. Pre-measured and easy to use and 2 part epoxy putty does not require tools. Hand mix and apply. NSF® approved for plumbing repairs and for contact with potable water supply pipes.  Here are just a few specific uses (there are hundreds of other uses): Seal leaks in copper pipes resulting from hard water Fix freeze damaged PVC and copper pipes Stop leaking copper elbow and tees Fill abandoned drill holes in ductwork Insulate electrical connections from water

Read more less

PC-Marine™ Epoxy Putty Stick is a specially formulated epoxy putty suitable for wet or underwater applications. Incredibly it has an extended open time (20 – 30 minutes) but cures hard within 60 minutes for a fast return to service and emergency repairs. It sticks great to metals, fibreglass, tile, wood and some plastics such as ABS and rigid PVC. Here are just a few specific uses (there are hundreds of other uses): Seal holes and waterproof fittings Shape and form missing corners or holes in ceramic or fibreglass fixtures Re-attach and secure loose hardware Fill cracks and dings in fibreglass Seal leaks in water tanks How to prepare a surface for bonding with PC-Marine™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol, acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use mineral spirits or paint thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-Marine™ application Wear disposable gloves to minimize contact with the skin. Use denatured alcohol, acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner to cleanup before PC-Marine cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying paint remover or paint stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. Can PC-Marine™ be applied underwater? Yes, application underwater is possible. PC-Marine™ will adhere and cure underwater. However, it is preferable to apply it in dry conditions. Is PC-Marine™ suitable for repairing canoes? PC-Marine™ is excellent for repairs to aluminium and fibreglass canoes but not when they are made with Hypalon. How much time does it take for PC-Marine™ to cure? PC-Marine™ has an extended application or open time of 20 minutes. Most repairs made with PC-Marine™ can be returned to service after 60 minutes. Some applications may require a full 24-hour cure. Is PC-Marine™ green? PC-Marine™ Epoxy Putty stick is white on the inside and green on the outside. The green colour disappears when mixed with the white. The result is an off-white colour when it cures. What is the maximum thickness that PC-Marine™ Epoxy Putty can be applied? PC-Marine™ can be applied thick or thin. There isn’t a thickness limit. It cures from the within via a chemical reaction. It does not need to dry or be exposed to air. How much PC-Marine™ can be mixed at a single time? PC-Marine™ is slower curing than other epoxy putties allowing larger portions to be mixed at one time. Small quantities can be mixed more thoroughly and with less effort. Can PC-Marine™ cure in a freezer? PC-Marine™ is not recommended for sub-freezing temperatures. We recommend an application temperature of 2°C or higher. Does PC-Marine shrink? PC-Marine™ does not shrink.

Read more less

PC-Crete™ Epoxy is a hand-mixable, fast-setting epoxy putty that quickly repairs concrete and masonry. After mixing, it forms a concrete repair polymer that cures to a concrete-like color and texture. The mixture readily sticks to concrete and masonry surfaces and is easily shaped. It will stick to ceramics, glass, metals and some plastics. It cures within 60 minutes. Each stick contains pre-measured portions of activator and base — no measuring or mixing tools are necessary. Here are just a few specific uses (there are hundreds of other uses): Quickly rebuild small missing pieces of concrete Fill holes in concrete and masonry Rebuild missing pieces of statues and birdbaths Seal hole for wire or conduit thru cinder block Fill chip or spall in concrete furniture Reattach loose or popped decorative stone Fill crack in stone fireplace Fill holes in brick or concrete walls; Apartment complexes, schools, government buildings etc. Fill cracks in concrete or stucco wall before painting Attach address numbers to brick or stone Attach hardware to brick or stone Fill abandoned screw holes and mounting holes in brick or cinderblock Replace missing mortar Seal rodent hole in cinderblock or concrete How to prepare a surface for bonding with PC-Crete™ Old concrete must be clean and profiled or textured. Surface must be clean and sound. It may be dry or damp, but free of standing water. Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use mineral spirits or paint thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-Crete™ application Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be removed with paint stripper or remover. Can PC-Crete™ be used to repair a crack in a fountain? PC-Crete™ looks like concrete and is excellent for repairing concrete fountains, statues and lawn decorations. Will PC-Crete™ adhere to a concrete step? Can it be shaped to match a corner? PC- Crete™ is excellent to repairs on concrete surfaces such as steps. It shapes easily and can be sanded to match the look and texture of the concrete surface. Is PC-Crete™ suitable for filling a small crack or spall in a sidewalk or deck? Small crack repairs in concrete are easily made with or without the use of tools using PC-Crete™. PC-Crete™ is excellent for replacing missing or loose mortar between bricks and stones. Can PC-Crete™ be used in a fish tank or pond? PC-Crete™ is not recommended for aquatic use. Do not use this product in aquariums or ponds. The PC-Crete™ is not easily grabbing or sticking to the concrete surface. It pulls away lifting loose stones The putty wants to stick to the fingers more than the concrete surface. Wet the fingers with alcohol and then press, shape and smooth the applied putty. Also, loose stones can be wire brushed away to provide a sound surface. PC-Crete™ does not have a smooth texture. It has particles throughout The particles in PC-Crete™ are used to simulate the appearance of concrete.

Read more less

Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.

Read more less

Sanitary grade silicone Acetic cure Excellent adhesion Watertight seal Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.

Read more less

Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on! Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours. FEATURES Premium quality 100% silicone Ideal for wet areas Indoor and outdoor use Maximum flexibility BENEFITS Proven to last in all weather Mould resistant Tack free in 10 minutes Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.

Read more less

Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on! Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours. FEATURES Premium quality 100% silicone Ideal for wet areas Indoor and outdoor use Maximum flexibility BENEFITS Proven to last in all weather Mould resistant Tack free in 10 minutes Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.

Read more less

Monarch Mini Roof & Gutter Silicone is a neutral cure silicone sealant that is ideal for repairing or installing gutters, roofs, downpipes, skylights and more. It can also be used to install metal sheets in the roofing industry and various other building services.  With such versatility on offer it's no wonder this product's demand has soared so rapidly! What else would you want from your sealant? Well there are added features like its flexibility and resilience that make it perfect for all applications. You can count on Monarch Mini Roof & Gutter Silicone to stick around because of its long-lasting durability - don't wait until disaster strikes again when you could have had the protection you needed beforehand. FEATURES Premium quality 100% silicone Non-corrosive Neutral cure AS 4020 approved BENEFITS Quick exposure to light running water Suitable for use in all weather UV resistant Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.  

Read more less

CLR Calcium, Lime & Rust Remover Need to tackle tough calcium and lime deposits as well as rust stains? CLR Calcium, Lime & Rust Remover is a powerful formula that quickly and easily dissolves and removes tough calcium and lime deposits as well as surface rust stains from bathtubs, toilet bowls, sinks, glass, chrome, fiberglass, stainless steel, kettles, humidifiers, dishwashers, washing machines and showerheads. The formula also is ideal for use on caravans and boats. CLR Calcium, Lime & Rust Remover is part of the EPA’s Safer Choice Program recognising the product as a safer alternative to chemicals. The fast-acting, powerful CLR formula is septic-safe and contains no phosphates. Always spot test in an inconspicuous area before beginning to clean. What can you clean with CLR ? CLR cleans what many household products can’t. It dissolves and removes tough stains from the build-up of calcium, limescale and surface rust from hard water. You may not know what these are but chances are you’re living with them. Some examples where CLR can be used are; poor performing showerheads dishwashers washing machines shower screens inside your kettle on your taps inside and outside toilet bowls sinks on cloudy glass inside and outside chrome fiberglass stainless steel humidifiers surface rust stains on tools taps Plus many more. If you have a specific surface that you would like to know can be cleaned with CLR, search the material on our Frequently Asked Questions to find the answer. If it is not there – contact us. When you say diluted, how much water to CLR do I use? Use equal parts CLR to water i.e. 1 cup CLR mixed with 1 cup water. Is it septic safe? Yes, CLR is septic safe How do I use on a stain in my toilet? Wear household gloves. Mix equal parts CLR and warm water. Apply directly to stain with a brush, cloth or sponge. Rinse promptly with cold water. If the stain does not disappear use CLR full strength, wipe and rinse properly. How long should I leave CLR on the stain for? We recommend you do not leave on the stain for longer than a few minutes. Do not leave CLR on the stain and walk away from it. Always rinse thoroughly. Can I use CLR on my car (radiator, window etc)? No. Not recommended for use on cars as it may damage paintwork and/or interiors. Can I use on my chlorinated swimming pool tiles? No. CLR can react with pool chlorine leading to potentially dangerous reactions which must be avoided. What is the main ingredient in CLR? Calcium Lime Rust, more commonly known as CLR, is a household cleaning product used for dissolving stains, such as calcium, lime, and iron oxide deposits. Its ingredients include water, lactic acid, gluconic acid, lauramine oxide,Propylene Glycol, n-Butyl Ether, and solvents that dissolve cobalt gel coats and paint. How do you use CLR? Test the solution on a hidden area before applying to the entire surface. Apply directly to the calcium, lime or rust stain with a brush, cloth or sponge and rinse promptly with cold, clean water. Never leave CLR on an area for longer than two minutes. Safer Choice Finding cleaning and other products that are safer for you, your family, and the environment should be easy — that's why the U.S. EPA developed a Safer Choice label. We all play a role in protecting our families’ health and the environment. Products with the Safer Choice label help consumers and commercial buyers identify products with safer chemical ingredients, without sacrificing quality or performance. CLR, CLR Bathroom and Kitchen, CLR Outdoor Furniture Cleaner all wear the Safer Choice label to communicate that the product’s formula contain ingredients with more positive human health and environmental characteristics than conventional products of the same type. They are also biodegradable.

Read more less